kep dirjen migas no-84-k 38 djm 1998

21
DEPARTEMEN PERTAMBANGAN DAN ENERGI REPUBLIK INDONESIA DIREKTORAT JENDERAL MINYAK DAN GAS BUMI KEPUTUSAN DIREKTUR JENDERAL MINYAK DAN GAS BUMI Nomor 84.K/38/DJM/1998 TENTANG PEDOMAN DAN TATACARA PEMERIKSAAN KESELAMATAN KERJA ATAS INSTALASI, PERALATAN DAN TEKNIK YANG DIPERGUNAKAN DALAM USAHA PERTAMBANGAN MINYAK DAN GAS BUMI DAN PENGUSAHAAN SUMBERDAYA PANASBUMI DIREKTUR JENDERAL MINYAK DAN GAS BUMI Memimbang : bahwa dalam rangka kelancaran pelaksanaan pemeriksaaan keselamatan kerja atas instalasi, peralatan dan teknik yang dipergunakan dalam usaha pertambangan minyak dan gas bumi dan pengusahaan sumberdaya panasbumi dan sebagai pelaksanaan lebih lanjut Peraturan Menteri Pertambangan dan Energi Nomor 06 P/ 0746/ M.PE/1991 tanggal 19 Nopember 1991, dianggap perlu menerapkan Pedoman dan Tatacara Pemeriksaan Keselamatan Kerja atas Instalasi, Peralatan dan Teknik Yang Dipergunakan Dalam Usaha Pertambangan Minyak dan Gas Bumi Dan Pengusahaan Sumberdaya Panasbumi dalam suatu Keputusan Direktur Jenderal Minyak dan Gas Bumi ; Mengingat : 1. Undang-undang Nomor 44 Prp Tahun 1960 (L.N. Tahun 1960 Nomor 33, TLN Nomor 2070) ; 2. Undang-undang Nomor 8 Tahun 1971 (L.N. Tahun 1971 Nomor 76, TLN Nomor 2971) ; 3. Mijn Politie Reglement 1930 Sb. 1930 Nomor 341) ; 4. Peraturan Pemerintah Nomor 11 Tahun 1979 MINISTRY OF MINES AND ENERGY OF THE REPUBLIC OF INDONESIA DIRECTORATE GENERAL OF OIL AND GAS DECREE OF THE DIRECTOR GENERAL OF OIL AND GAS Number 84.K/38/DJM/1998 REGARDING INSPECTION GUIDELINES AND PROCEDURES FOR OCCUPATIONAL SAFETY OF THE PLANT, EQUIPMENT AND ENGINEERING EMPLOYED IN THE MINING OPERATIONS OF OIL AND GAS AS WELL AS EXPLOITATION OF GEOTHERMAL RESOURCES THE DIRECTOR GENERAL OF OIL AND GAS Considering : that in the framework of smooth implementation of the inspection for occupational safety of the plant, equipment and engineering employed in the mining operations of Oil and Gas as well as exploitation of geothermal resources and as further implementation of the Regulation of the Minister of Mines and Energy Number 06 P/ 0746/ M.PE/1991 dated 19 th November 1991, it is deemed necessary to stipulate Inspection Guidelines and Procedures for Occupational Safety of the Plant, Equipment and Engineering employed in the Mining Operations of Oil and Gas as well as Exploitation of Geothermal Resources in a Decree of the Director General of Oil and Gas; Taking into Account : 1. Law Number 44 Prp of 1960 (Official Gazette of 1960 Number 33, Supplement to the Official Gazette Number 2070); 2. Law Number 8 of 1971 (Official Gazette of 1971 Number 76, Supplement to the Official Gazette Number 2971); 3. Mijn Politie Reglement of 1930 (Sb. Of 1930 Number 341); 4. Government Regulation Number 11 of 1979; WTCJ-02116 1 Decicion of the Director General of Petroleum and Gas No.84.K/38/DJM/1998

Upload: krisnandar74

Post on 26-Oct-2014

1.287 views

Category:

Documents


26 download

TRANSCRIPT

Page 1: Kep Dirjen Migas No-84-K 38 DJM 1998

DEPARTEMEN PERTAMBANGAN DAN ENERGI REPUBLIK INDONESIA

DIREKTORAT JENDERAL MINYAK DAN GAS BUMI

KEPUTUSAN DIREKTUR JENDERAL MINYAK DAN GAS BUMI

Nomor 84.K/38/DJM/1998

TENTANG

PEDOMAN DAN TATACARA PEMERIKSAAN KESELAMATAN KERJA ATAS INSTALASI,

PERALATAN DAN TEKNIK YANG DIPERGUNAKAN DALAM USAHA

PERTAMBANGAN MINYAK DAN GAS BUMI DAN PENGUSAHAAN SUMBERDAYA

PANASBUMI

DIREKTUR JENDERAL MINYAK DAN GAS BUMI

Memimbang : bahwa dalam rangka kelancaran pelaksanaan pemeriksaaan keselamatan kerja atas instalasi, peralatan dan teknik yang dipergunakan dalam usaha pertambangan minyak dan gas bumi dan pengusahaan sumberdaya panasbumi dan sebagai pelaksanaan lebih lanjut Peraturan Menteri Pertambangan dan Energi Nomor 06 P/ 0746/ M.PE/1991 tanggal 19 Nopember 1991, dianggap perlu menerapkan Pedoman dan Tatacara Pemeriksaan Keselamatan Kerja atas Instalasi, Peralatan dan Teknik Yang Dipergunakan Dalam Usaha Pertambangan Minyak dan Gas Bumi Dan Pengusahaan Sumberdaya Panasbumi dalam suatu Keputusan Direktur Jenderal Minyak dan Gas Bumi ; Mengingat : 1. Undang-undang Nomor 44 Prp Tahun 1960 (L.N. Tahun 1960 Nomor 33, TLN Nomor 2070) ; 2. Undang-undang Nomor 8 Tahun 1971

(L.N. Tahun 1971 Nomor 76, TLN Nomor 2971) ;

3. Mijn Politie Reglement 1930 Sb. 1930 Nomor 341) ;

4. Peraturan Pemerintah Nomor 11 Tahun 1979

MINISTRY OF MINES AND ENERGY OF THE REPUBLIC OF INDONESIA

DIRECTORATE GENERAL OF OIL AND GAS

DECREE OF THE DIRECTOR GENERAL OF OIL AND GAS

Number 84.K/38/DJM/1998

REGARDING

INSPECTION GUIDELINES AND PROCEDURES FOR OCCUPATIONAL SAFETY

OF THE PLANT, EQUIPMENT AND ENGINEERING EMPLOYED IN THE MINING OPERATIONS OF OIL AND GAS AS WELL AS

EXPLOITATION OF GEOTHERMAL RESOURCES

THE DIRECTOR GENERAL OF

OIL AND GAS

Considering : that in the framework of smooth implementation of the inspection for occupational safety of the plant, equipment and engineering employed in the mining operations of Oil and Gas as well as exploitation of geothermal resources and as further implementation of the Regulation of the Minister of Mines and Energy Number 06 P/ 0746/ M.PE/1991 dated 19th November 1991, it is deemed necessary to stipulate Inspection Guidelines and Procedures for Occupational Safety of the Plant, Equipment and Engineering employed in the Mining Operations of Oil and Gas as well as Exploitation of Geothermal Resources in a Decree of the Director General of Oil and Gas;

Taking into Account : 1. Law Number 44 Prp of 1960 (Official Gazette of

1960 Number 33, Supplement to the Official Gazette Number 2070);

2. Law Number 8 of 1971 (Official Gazette of 1971

Number 76, Supplement to the Official Gazette Number 2971);

3. Mijn Politie Reglement of 1930 (Sb. Of 1930

Number 341); 4. Government Regulation Number 11 of 1979;

WTCJ-02116 1 Decicion of the Director General of Petroleum and Gas No.84.K/38/DJM/1998

Page 2: Kep Dirjen Migas No-84-K 38 DJM 1998

5. Keputusan Presiden Nomor 22 Tahun 1981 tanggal

1 Juni 1981 Jo. Keputusan Presiden Nomor 45 Tahun 1991 tanggal 1 Oktober 1991 ;

6. Keputusan Presiden Nomor 374/M Tahun 1995

tanggal 23 Nopember 1995 ; 7. Peraturan Menteri Pertambangan dan Energi

Nomor 02/P/M/Pertamb/1975 tanggal 10 Maret 1975 ;

8. Keputusan Menteri Pertambangan dan Energi

Nomor 02/P/M/Pertamb/1979 tanggal 30 Juni 1979 9. Keputusan Menteri Pertambangan dan Energi

Nomor 521/Kpts/1979 tanggal 20 Juni 1979 ; 10. Peraturan Menteri Pertambangan dan Energi

Nomor 06 P/0746/M.PE/1991 tanggal 19 Nopember 1991 ;

11. Keputusan Menteri Pertambangan dan Energi

Nomor 300.K/38/M.PE/1997 tanggal 28 April 1997 ;

12. Peraturan Direktur Jenderal Minyak dan Gas Bumi

Nomor 43P/382/DDJM/1992 tanggal 19 September 1992 ;

MEMUTUSKAN :

Menetapkan : KEPUTUSAN DIREKTUR JENDERAL MINYAK DAN GAS BUMI TENTANG PEDOMAN DAN TATACARA PEMERIKSAAN KESELAMATAN KERJA ATAS INSTALASI, PERALATAN DAN TEKNIK YANG DIPERGUNAKAN DALAM USAHA PERTAMBANGAN MINYAK DAN GAS BUMI DAN PENGUSAHAAN SUMBERDAYA PANASBUMI.

Pasal 1 (1) Segala definisi atau pengertian yang dipergunakan

dalam Keputusan ini adalah definisi atau pengertian sebagaimana dimaksud dalam Pasal 1 Keputusan Menteri Pertambangan dan Energi Nomor 06P/0746/M.PE/1991 tanggal 19 Nopembner 1991

(2) Selain sebagaimana telah ditetapkan pada ayat (1),

dalam Keputusan ini yang dimaksud dengan :

5. Presidential Decree Number 22 of 1981 dated 1st

June 1981 Jo. Presidential Decree Number 45 of 1991 dated 1st October 1991;

6. Presidential Decree Number 374/M of 1995 dated

23rd November 1995; 7. Regulation of the Minister of Mines and Energy

Number 02/P/M/Pertamb/1975 dated 10th March 1975;

8. Decree of the Minister of Mines and Energy

Number 02/P/M/Pertamb/1979 dated 30th June 1979;

9. Decree of the Minister of Mines and Energy

Number 521/Kpts/1979 dated 20th June 1979; 10. Regulation of the Minister of Mines and Energy

Number 06 P/0746/M.PE/1991 dated 19th November 1991;

11. Decree of the Minister of Mines and Energy

Number 300.K/38/M.PE/1997 dated 28th April 1997;

12. Regulation of the Director General of Petroleum

and Gas Number 43P/382/DDJM/1992 dated 19th September 1992;

DECIDED :

To draw up : DECREE OF THE DIRECTOR GENERAL OF OIL AND GAS REGARDING INSPECTION GUIDELINES AND PROCEDURES FOR OCCUPATIONAL SAFETY OF THE PLANT, EQUIPMENT AND ENGINEERING EMPLOYED IN THE MINING OPERATIONS OF OIL AND GAS AS WELL AS EXPLOITATION OF GEOTHERMAL RESOURCES.

Article 1

(1) Any definitions or terminologies used in this Decree shall be definitions or terminologies as referred to in Article 1 of the Decree of the Minister of Mines and Energy Number 6P/0746/M.PE/1991 dated 19th November 1991.

(2) In addition to those as already provided in

paragraph (1), in this Decree, meant by :

WTCJ-02116 2 Decicion of the Director General of Petroleum and Gas No.84.K/38/DJM/1998

Page 3: Kep Dirjen Migas No-84-K 38 DJM 1998

a. Sertifikat Kelayakan Penggunaan, adalah persetujuan yang diberikan Direktur Jenderal atas operasi atau penggunaan Instalasi dan Peralatan setelah dilakukan pemeriksaan Keselamatan Kerja, yang berupa Sertifikat Kelayakan Penggunaan Instalasi (SKPI) dan Sertifikat Kelayakan Penggunaan Peralatan (SKPP);

b. Direktorat Jenderal, adalah Direktorat Jenderal Minyak dan Gas Bumi;

c. Direktur, adalah Direktur Teknik Pertambangan Minyak dan Gas Bumi;

d. Direktorat Teknik, adalah Direktorat Teknik Pertambangan Minyak dan Gas Bumi;

e. Kepala Pelaksana Inspeksi Tambang, adalah Kepala Inspeksi Tambang Minyak dan Gas Bumi;

f. Pelaksana Inspeksi Tambang, adalah pejabat Direktorat Jenderal yang diangkat oleh Direktur Jenderal

g. Perusahaan, adalah Pertamina, Kontraktor Kontrak Production Sharing, Technical Assistance, Joint Operating Body, dan mitra kerja Pertamina lainnya dalam operasi Minyak dan Gas Bumi dan Kontraktor Kontrak Operasi Bersama Pengusahaan Sumberdaya Panasbumi;

h. Perusahaan Jasa adalah Perusahaan Jasa Inspeksi Teknik dalam bidang pertambangan minyak dan gas bumi dan pengusahaan sumberdaya panasbumi yang telah mendapatkan penunjukan Direktur Jenderal.

Pasal 2 (1) Terhadap Instalasi dan Peralatan dalam operasi

pertambangan minyak dan gas bumi wajib dilaksanakan pemeriksaan Keselamatan Kerja.

(2) Pemeriksaan Keselamatan Kerja sebagaimana dimaksud pada ayat (1) dilakukan terhadap Instalasi dan Peralatan yang : a. akan dipasang atau didirikan; b. sedang dipasang atau didirikan; c. telah dipasang atau didirikan.

a. Worthiness Operation Certificate shall be approval given by the Director General of the operation or use of the Plant and Equipment after being carried out an Inspection for Occupational Safety in the form of a Worthiness of Plant Installation Certificate (SKPI) and Worthiness of Equipment Operation Certificate (SKPP);

b. Directorate General shall be the Directorate

General of Oil and Gas; c. Director shall be the Director of Oil and Gas

Mining Engineering;

d. Engineering Directorate shall be the Directorate of Oil and Gas Mining Engineering;

e. Mine Head Inspector shall be the Oil and Gas

Mine Inspection Head; f. Mine Inspector shall be an officer of the

Directorate General appointed by the Director General;

g. Company shall be Pertamina, Production

Sharing Contractor. Technical Assistance, Joint Operating Body and another work partner of Pertamina in the Oil and Gas operations and Joint Operation Contract Contractor in the Exploitation of Geothermal Resources;

h. Service Company shall be an Technical

Inspection Service Company in the fields of Oil and Gas mining and exploitation of geothermal resources already having an appointment from the Director General.

Article 2

(1) Of the Plant and Equipment in the mining operations of Oil and Gas, shall be carried out an inspection for Occupational Safety.

(2) The Inspection for Occupational Safety as referred

to in paragraph (1) shall be carried out of the Plant and Equipment which : a. will be installed or erected; b. is being installed or erected; c. has been installed or erected.

WTCJ-02116 3 Decicion of the Director General of Petroleum and Gas No.84.K/38/DJM/1998

Page 4: Kep Dirjen Migas No-84-K 38 DJM 1998

(3) Terhadap peralatan yang dibuat berdasarkan

pesanan dan bukan merupakan produksi masal, pemeriksaan Keselamatan Kerja dapat dilakukan ditempat pembuatan peralatan.

Pasal 3 Instalasi dan Peralatan yang wajib dilaksanakan pemeriksaan Keselamatan Kerja adalah sebagaimana termasksud dalam Lampiran I Keputusan ini.

Pasal 4 (1) Pemeriksaan Keselamatan Kerja atas Instalasi dan

Peralatan sebagaiman dimaksud dalam Pasal 2 dilaksanakan oleh Pelaksana Inspeksi Tambang dan atau oleh Perusahaan Jasa.

(2) Tatacara Pemeriksaan Keselamatan Kerja atas Instalasi dan Peralatan adalah sebagaimana termaksud dalam Lampiran II Keputusan ini.

Pasal 5 (1) Terhadap Instalasi dan Peralatan yang telah

dilaksanakan pemeriksaan Keselamatan Kerja diberikan Sertifikat Kelayakan Penggunaan Instalasi (SKPI) dan Sertifikat Kelayakan Penggunaan Peralatan (SKPP) oleh Direktur Jenderal

(2) Sertifikat Kelayakan Penggunaan Instalasi (SKPI) dan Sertifikat Kelayakan Penggunaan Peralatan (SKPP) sebagaimana dimaksud pada ayat (1) berlaku selama jangka waktu 5 (lima) tahun untuk SKPI dan 3 (tiga) tahun untuk SKPP, atau kurang dari jangka waktu tersebut di atas apabila Instalasi dan Peralatan tersebut mengalami perubahan atau diragukan kemampuannya.

(3) Setalah selesainya jangka waktu sebagaimana dimaksud pada ayat (2), terhadap Instalasi dan Peralatan wajib dilakukan pemeriksaan Keselamatan Kerja sebagaimana dimaksud dalam Pasal 2.

Pasal 6

Setelah dilaksanakan evaluasi terhadap teknik yang akan dipergunakan sebagaimana termaksud dalam Lampiran I huruf C, Direktur Jenderal Cq. Direktur memberikan pengesahan.

(3) Of the equipment manufactured based on an order

and not mass production, the inspection for Occupational Safety can be carried out in the place where the equipment is manufactured.

Article 3 The Plant and Equipment of which the inspection for Occupational Safety shall be carried out shall be as referred to in Attachment 1 to this Decree.

Article 4

(1) The Inspection for Occupational Safety of the Plant and Equipment as referred to in Article 2 shall be carried out by the Mine Inspector and / or by the Service Company.

(2) The Inspection procedures for Occupational Safety

of the Plant and Equipment shall be as referred to in Attachment II to this Decree.

Article 5

(1) For the Plant and Equipment of which the

inspection for Occupational Safety has been carried out shall be issued a Worthiness of Plant Installation Certificate (SKPI) and Worthiness of Equipment Operation Certificate (SKPP) by the Director General.

(2) The Worthiness of Plant Installation Certificate

(SKPI) and Worthiness of Equipment Operation Certificate (SKPP) as referred to in paragraph (1) shall be valid for a period of 5 (five) years for SKPI and 3 (three) years for SKPP, or less than the periods as mentioned above if the Plant and Equipment has a modification or its ability is doubted.

(3) After the periods as referred to in paragraph (2)

have ended, of the Plant and Equipment shall be carried out an inspection for Occupational Safety as referred to in Article 2.

Article 6

After a technical evaluation which will be employed as referred to in Attachment I letter C has been carried out, the Director General Cq. Director shall issue ratification.

WTCJ-02116 4 Decicion of the Director General of Petroleum and Gas No.84.K/38/DJM/1998

Page 5: Kep Dirjen Migas No-84-K 38 DJM 1998

Pasal 7

Besarnya biaya pemeriksaan Keselamatan Kerja atas Instalasi dan Peralatan yang dilaksanakan oleh Perusahaan Jasa ditetapkan berdasarkan mekanisme pasar tenaga kerja bidang minyak dan gas bumi.

Pasal 8 Dalam jangka waktu 6 (enam) bulan sejak berlakunya Keputusan ini, Perusaan yang telah beroperasi atau telah menggunakan Instalasi dan Peralatan dan belum melakukan ketentuan dan Keputusan ini wajib mengajukan permohonan pemeriksaan Keselamatan Kerja atas Instalasi, Peralatan dan Teknik yang dipergunakan kepada Direktorat Jenderal cq. Direktorat Teknik.

Pasal 9 Apabila terdapat kekurangan-kekurangan pada Instalasi atau Peralatan setelah diadakan pemeriksaan Keselamatan Kerja, maka dalam waktu yang ditetapkan oleh Direktur, Perusahaan wajib mengadakan perbaikan atau perubahan sehingga Instalasi dan Peralatan tersebut memenuhi hal-hal yang disyaratkan oleh peraturan perundang-undangan yang berlaku.

Pasal 10 Keputusan ini berlaku pada tanggal ditetapkan.

Ditetapkan di Jakarta Pada tanggal, 19 Agustus 1998 Direktur Jenderal Minyak dan Gas Bumi Soepraptono Soeleiman

Article 7

The amount of the inspection cost for Occupational Safety of the Plant and Equipment carried out by the Service Company shall be fixed based on the mechanism of the labour (manpower) market in the fields of petroleum and Gas.

Article 8

In a period of 6 (six) months since the effectiveness of this Decree, the Company which has been operating or employing the Plant and Equipment and has not yet implemented the provisions of this Decree shall be under an obligation to submit an application for an inspection for Occupational Safety of the Plant, Equipment and Engineering employed to the Directorate General cq. Engineering Directorate.

Article 9

In case of shortcomings in the Plant or Equipment after being carried out an inspection for Occupational Safety, then in a period as stipulated by the Director, the Company shall be under an obligation to make repairs or modifications so that the Plant and Equipment will satisfy the matters required by the prevailing legislative regulations.

Article 10 This Decree shall come into effect as of its stipulation date.

Stipulated in Jakarta On 19th August 1998

The Directorate General of Oil and Gas

Soepraptono Soeleiman

WTCJ-02116 5 Decicion of the Director General of Petroleum and Gas No.84.K/38/DJM/1998

Page 6: Kep Dirjen Migas No-84-K 38 DJM 1998

Lampiran I Keputusan Direktur Jenderal Minyak dan Gas Bumi Nomor : 84.K/38/DJM/1998 Tanggal : 19 Agustus 1998 -------------------------------------

INSTALASI DAN PERALATAN YANG WAJIB DILAKSANAKAN PEMERIKSAAN

KESELAMATAN KERJA A. Instalasi

1. Instalasi Ekplorasi dan Eksploitasi : a. Instalasi pemboran; b. Instalasi produksi; c. Instalasi pengumpulan d. Instalasi lainnya yang terkait dengan

kegiatan Eskplorasi dan Eksploitasi

2. Instalasi Pemurnian dan Pengolahan : a. Instalasi Pemurnian dan Pengolahan; b. Pembongkaran dan Pemuatan; c. Instalasi lainnya yang terkait dengan

kegiatan Pemurnian dan Pengolahan baik langsung maupun tidak langsung berhubungan dengan kegiatan termaksud.

3. Instalasi Penimbunan dan Pemasaran yang

dimaksud adalah : a. Instalasi Seafed Depot; b. Instalasi Inland Depot; c. Instalasi Depot Pengisian Pesawat Udara

(DPPU); d. Instalasi Transit Terminal; e. Instalasi Stasiun Pengisian Bahan Bakar

Umum (SPBU) dan Stasiun Pengisian Bahan Bakar Gas (SPBG);

f. Instalasi lainnya yang terkait dengan kegiatan penimbunan dan pemasaran

B. Peralatan

1. Katup Pengaman yaitu peralatan yang berguna untuk melindungi peralatan dan fasilitas yang terkait meliputi :

a. Safety Vale; b. Relief Valve; c. Safety Relief Valve; d. Thermal Relief Valve; e. Pilot Operated Safety Valve; f. Vacuum Relief Valve.

Attachment I to the Decree of the Director General of Oil and Gas Number : 84.K/38/DJM/1998 Dated : 19th August 1998 --------------------------------------

PLANT AND EQUIPMENT SUBJECT TO THE INSPECTION FOR OCCUPATIONAL SAFETY

A. Plant 1. Exploration and Exploitation Plant : a. Drilling plant; b. Production plant; c. Gathering plant

d. Other plant related to the Exploration and Exploitation activities

2. Refinement and Treatment Plant : a. Refinement and Treatment Plant; b. Unloading and Loading; c. Other plant related to the Refinement and

Treatment activities, either directly or indirectly related to the activities in question.

3. Storage and Marketing Plant, that is :

a. Seafed Depot Plant; b. Inland Depot Plant; c. Aircraft Fuelling Depot (DPPU) Plant; d. Transit Terminal Plant; e. Public Fuelling Station (SPBU) and Gas

Fuelling Station (SPBG) Plant; f. Other plant related to the storage and

marketing activities

B. Equipment

1. Safety Valves, that is equipment useful to protect the related equipment and facilities comprising :

a. Safety Valve; b. Relief Valve; c. Safety Relief Valve; d. Thermal Relief Valve; e. Pilot Operated Safety Valve; f. Vacuum Relief Valve.

WTCJ-02116 6 Decicion of the Director General of Petroleum and Gas No.84.K/38/DJM/1998

Page 7: Kep Dirjen Migas No-84-K 38 DJM 1998

2. Bejana Tekan dan sejenisnya yaitu peralatan

yang bekerja dengan tekanan kerja didalam peralatan melebihi ½ Atm tekanan lebih (gauge), atau bejana vakum dengan tekanan kerja didalam peralatan kurang dari 1 Atm absolut.

3. Pesawat Angkat yaitu peralatan untuk

memindahkan, mengangkat barang secara vertikal dan atau horizontal dalam jarak, antara lain meliputi : a. Pesawat Angkat Bergerak; b. Pesawat Angkat Tetap; c. Pesawat Angkat di atas kepala.

4. Peralatan Listrik yaitu peralatan yang

membangkit, mendistribusi dan mengendalikan sistem tenaga listrik meliputi : a. Unit Power Generator; b. Unit Power Transformer; c. Unit Switcher; d. Unit Motor Control Center.

5. Peralatan Putar yaitu peralatan yang berfungsi

memindahkan atau memampatkan minyak, gas serta panasbumi meliputi : a. Unit Kompresor; b. Unit Pompa.

6. Pipa Penyalur yaitu bentang pipa berikut

fasilitas-fasilitas terkait yang digunakan untuk mengalirkan dan menyalurkan minyak dan gas bumi serta panasbumi.

C. Teknik Yang Dipergunakan

Teknik yang dipergunakan yaitu tata cara atau prosedur yang akan dipergunakan dalam operasi pertambangan minyak dan gas bumi antara lain meliputi : 1. Spesifikasi Prosedur Las (WPS) dan Rekaman

Kualifikasi Prosedur (PQR); 2. Catatan Unjuk Kerja (Sertifikat) Juru Las /

Operator Las; 3. Prosedur Uji Tekan Pipa Penyalur; 4. Prosedur Uji Beban Pesawat Angkat; 5. Prosedur Reparasi, Modifikasi dan Alterasi.

2. Pressure Vessel and the like, that is equipment

working with a work pressure within the equipment of more than ½ more pressure Atm (gauge), or vacuum vessel with a work pressure within the equipment of less than 1 absolute Atm.

3. Lifting Equipment / Crane, that is equipment

to remove, lift up goods vertically and / or horizontally at a distance, among others including : a. Mobile Cranes; b. Stationary Cranes; c. Overhead Cranes.

4. Electrical equipment, that is equipment

generating, distributing and controlling the electrical power system comprising :

a. Power Generator Unit; b. Power Transformer Unit;

c. Switcher Unit; d. Motor Control Center Unit.

5. Rotary Equipment, that is equipment

functioning to remove or compress petroleum, Gas and geothermal comprising :

a. Compressor Unit; b. Pump Unit.

6. Pipeline, that is a range of pipe together with

related facilities used to transmit and distribute Oil and Gas as well as geothermal.

C. Engineering Employed

The engineering employed, that is procedures which will be employed in the mining operations of Oil and Gas, among others includes : 1. Welding Procedures Specifications (WPS) and

Procedure Qualification Record (PQR); 2. Performance Record (Certificate) of the

Welder / Welding Operator; 3. Pressure Test Procedures for Pipeline; 4. Load Test Procedures; 5. Procedures for Repairs, Modification and

Alteration.

WTCJ-02116 7 Decicion of the Director General of Petroleum and Gas No.84.K/38/DJM/1998

Page 8: Kep Dirjen Migas No-84-K 38 DJM 1998

Ditetapkan di Jakarta Pada tanggal, 19 Agustus 1998 Direktur Jenderal Minyak dan Gas Bumi Soepraptono Soeleiman

Stipulated in Jakarta On 19th August 1998

The Director General of Oil and Gas

Soepraptono Soeleiman

WTCJ-02116 8 Decicion of the Director General of Petroleum and Gas No.84.K/38/DJM/1998

Page 9: Kep Dirjen Migas No-84-K 38 DJM 1998

Lampiran II Keputusan Direktur Jenderal Minyak dan Gas Bumi Nomor : 84.K/38/DJM/1998 Tanggal : 19 Agustus 1998 -------------------------------------- TATACARA PEMERIKSAAN KESELAMATAN

KERJA ATAS INSTALASI DAN PERALATAN

I. PEMERIKSAAN KESELAMATAN KERJA

INSTALASI A. Pemeriksaan Keselamatan Kerja Instalasi

meliputi penilaian perencanaan dengan melaksanakan penelaahan terhadap data :

a. Peralatan proses, utilitas dan pengolahan

limbah; b. Alat ukur dan metering; c. Sistem perpipaan; d. Sistem intrumentasi; e. Piranti pengaman; f. Tangki timbun; g. Sistem pencegahan dan penanggulangan

kebakaran; h. Sistem pencegahan dan pemantauan

pencemaran lingkungan; i. Peralatan lain; j. Diagram alir proses dan diagram pipa &

instrumen; k. Gambar tata letak peralatan; l. Pekerjaan sipil; m. Klasifikasi daerah berbahaya (hazardous area

classification); n. Electrical one line diagram; o. Gambar tata letak pentanahan (grounding lay-

out); p. Diagram cause & effect / SAFE Chart; q. Prosedur kerja pengoperasian peralatan; r. Prosedur evakuasi darurat; s. Surat persetujuan atau rekomendasi dari

instansi yang berwenang untuk program Pengolahan dan Pemantauan Lindungan Lingkungan.

B. Pemeriksaan fisik.

Pemeriksaan fisik meliputi : 1. Pemeriksaan Instalasi untuk memastikan

sesuai tidaknya Instalasi dengan perencanaan, spesifikasi, prosedur pembuatan dan pemasangan.

Attachment II to the Decree of the Director General of Oil and Gas Number : 84.K/38/DJM/1998 Dated : 19th August 1998 ------------------------------------

INSPECTION PROCEDURES FOR OCCUPATIONAL SAFETY OF THE PLANT

AND EQUIPMENT

1. INSPECTION FOR OCCUPATIONAL SAFETY OF THE PLANT

A. The Inspection for Occupational Safety of the

Plant includes an evaluation of the designs by reviewing of the data on :

a. Process, utilities and waste treatment

equipment; b. Measuring and metering devices; c. Piping system; d. Instrumentation system; e. Safety appliances; f. Storage tank; g. Fire prevention and control system; h. Environmental pollution monitoring and

prevention system; i. Other equipment; j. Process flow diagram and pipe & instrument

diagram; k. Equipment Layout drawing; l. Civil works; m. Hazardous area classification; n. Electrical one line diagram; o. Grounding layout; p. Cause & effect diagram / SAFE Chart; q. Operation Procedures of the equipment; r. Emergency evacuation procedures; s. Approval letter or recommendation from the

competent authorities for the Environmental Protection Monitoring and Processing program.

B. Physical Inspection The physical inspection includes :

1. Inspection of the Plant to ensure whether or not the Plant complies with the designs, specifications, manufacturing and installation procedures.

WTCJ-02116 9 Decicion of the Director General of Petroleum and Gas No.84.K/38/DJM/1998

Page 10: Kep Dirjen Migas No-84-K 38 DJM 1998

2. Memeriksa Kelengkapan Mutu Peralatan, Teknik Keselamatan Kerja dan Lindungan Lingkungan meliputi :

a. Alat Pemadam kebakaran; b. Alat deteksi api, panas, asap dan gas

berbahaya; c. Alat perlengkapan penyelamatan dan

pelindung perorangan; d. Sistem komunikasi; e. Sistem kontrol dan penghentian darurat

(emergency shutdown system); f. Pemeriksaan tangga, lampu, bordes dan

handrail; g. Flaring; h. Rock muffler i. Peralatan pencegahan dan penanggulangan

pencemaran lingkungan; j. Sistem untuk meniadakan bahaya listrik

statis dan arus listrik lainnya; k. Tanda-tanda keselamatan kerja, antara

lain; tanda peringatan, larangan, kode merah dan tanda lainnya.

3. Memeriksa Kelengkapan Sertifikat Kelayakan

Penggunaan Peralatan, Sertifikat Kelayakan Konstruksi Platform serta Ijin Penggunaan dari Instansi teknis terkait antara lain :

a. Katup pengaman; b. Bejana Tekan dan peralatan lain

sejenisnya; c. Peralatan Berputar (unit pompa dan unit

kompresor); d. Peralatan Listrik; e. Pesawat Angkat f. Pipa Penyalur g. Struktur Anjungan Lepas Pantai; h. Ketel Uap, Bejana Uap, Alat bantu

Navigasi, Alat Ukur & Metering, Alat Timbang, Helideck, Zat Radio Aktif, Bahan Peledak, dan lain-lain;

i. Peralatan penyelamatan dan perlindungan perorangan

4. Khusus Instalasi pemboran wajib dilakukan

pemeriksaan berkala sesuai dengan Pedoman Pelaksanaan Operasi Pemboran Darat dan Lepas Pantai Yang Aman di Indonesia (KK-01-DMJ).

5. Pemeriksaan Pre–Commissioning,

Commissioning dan Pengujian.

2. Inspection for the completeness of Quality of the Equipment, Occupational Safety Techniques and Environmental Protection including :

a. Fire Fighting Equipment; b. Fire, heat, smoke and hazardous gas

detectors; c. Personal protection and safety equipment; d. Communication system; e. Emergency shutdown and control system; f. Inspection of stairs, lights, flight of steps

and handrails; g. Flaring;

h. Rock muffler; i. Environmental pollution prevention and

control equipment; j. System to eliminate the hazards of static

electricity and other electric currents; k. Signs of occupational safety i.e : sign of

warning, prohibition, red code and other signs.

3. Inspection for the Completeness of the Worthiness of Equipment Operation Certificate, Worthiness of Platform Construction Certificate as well as Operation License from the related technical agencies, i.e : a. Safety Valve; b. Pressure Vessel and other similar

equipment; c. Rotary Equipment (pump unit and

compressor unit); d. Electrical equipment; e. Lifting Equipment; f. Pipeline; g. Offshore Platform Structure; h. Steam Boiler, Steam Vessel, Navigation

Aids, Measuring & Metering Devices, Weighing Equipment, Helideck, Radioactive Substance, Explosives, etc;

i. Individual protection and safety equipment.

4. The drilling plant shall specially be subject to a

periodic inspection pursuant to the Implementation Guidelines of Safe Onshore and Offshore Drilling Operations in Indonesia (KK-01-DMJ).

5. Pre-Commissioning, Commissioning and

Testing.

WTCJ-02116 10 Decicion of the Director General of Petroleum and Gas No.84.K/38/DJM/1998

Page 11: Kep Dirjen Migas No-84-K 38 DJM 1998

C. Pelaporan Menyusun seluruh hasil pemeriksaan teknis berbentuk dokumen untuk diserahkan ke Direktur Direktorat Teknik Pertambangan Minyak dan Gas Bumi sebagai bahan evaluasi untuk penerbitan Sertifikat Kelayakan Penggunaan Instalasi.

II. PEMERIKSAAN KESELAMATAN KERJA

ATAS PERALATAN : A. PEMERIKSAAN KESELAMATAN KERJA

KATUP PENGAMAN

Pemeriksaan teknis katup pengaman meliputi :

a. Penelaahan Dokumen - P & ID (Piping & Instrument Diagram) - Dokumen katup pengaman - Plat nama - Tipe katup pengaman :

* Konvensional * Pilot * Balance

- Sertifikat kelayakan Penggunaan test bench;

- Rekaman Kalibrasi pressure gauge / indicator;

- Perhitungan rekanan uji cold diff untuk menentukan tekanan buka nyata.

b. Pelaksanaan Pengujian - Uji tekanan buka - Uji bocor

c. Rekaman Hasil Uji

Rekaman hasil uji diisi berdasarkan dokumen katup pengaman, data plat nama serta data pengujian sebagai bahan evaluasi penerbitan Sertifikat Kelayakan Penggunaan Peralatan.

d. Penyegelan Penyegelan katup pengaman dilakukan oleh Pelaksana Inspeksi Tambang pada pengatur katup pengaman yang telah diuji dengan hasil baik dengan menggunakan Segel Migas.

C. Reporting

To prepare all the technical inspection results in the form of documents to be submitted to the Director of the Directorate of Petroleum and Gas Mining Engineering as evaluation material for the issue of the Worthiness of Plant Operation Certificate.

II. INSPECTION FOR OCCUPATIONAL

SAFETY OF THE EQUIPMENT : A. INSPECTION FOR OCCUPATIONAL

SAFETY OF THE SAFETY VALVE The technical inspection of the safety valve includes : a. Review of Documents

- P & ID (Piping & Instrument Diagram) - Safety valve document - Name plate - Types of safety valve : * Conventional * Pilot * Balance - Worthiness Certificate of Test Bench; - Indicator / pressure gauge calibration

record; - Cold diff test record calculation to stipulate

the real open pressure.

b. Test Implementation - Open pressure test - Leak test

c. Test Result Record

The test result record (form) should be completed based on the documents of safety valve, name plate data as well as test data as evaluation material of the issue of the Worthiness of Equipment Operation Certificate.

d. Sealing The safety valve sealing should be carried out by the Mine Inspector on the safety valve regulator already tested with good results by using the Migas (Directorate General of Oil and Gas) Seal.

WTCJ-02116 11 Decicion of the Director General of Petroleum and Gas No.84.K/38/DJM/1998

Page 12: Kep Dirjen Migas No-84-K 38 DJM 1998

B. PEMERIKSAAN KESELAMATAN KERJA BEJANA TEKAN DAN SEJENISNYA Pemeriksaan Teknis bejana tekan dan sejenisnya dibedakan menjadi 3 (tiga) bagian :

1. Bejana tekan dan sejenisnya yang baru

dan atau akan dipasang. 2. Bejana tekan dan sejenisnya yang lama

dan atau telah dipasang. 3. Bejana tekan dan sejenisnya yang

mengalami reparasi / alterasi / modifikasi..

B.1. Pemeriksaan teknis bejana dan sejenisnya

yang baru dan atau akan dipasang.

a. Penelaahan data yang meliputi : - Gambar konstruksi dan perhitungan

bejana tekan; - Spesifikasi material yang digunakan; - Spesifikasi prosedur las dan rekaman

kualifikasi prosedur serta catatan kualifikasi (sertifikat) unjuk kerja juru / operator las;

- Prosedur uji tidak merusak dan

kualifikasi personilnya; - Prosedur reparasi - Prosedur perlakuan panas pasca las (bila

disyaratkan); - Prosedur uji tekan;

b. Pemeriksaan fisik yang meliputi :

- Verifikasi sistem pengendalian mutu pemanufaktur;

- Identifikasi material yang akan digunakan;

- Verifikasi pembentukan bejana; - Verifikasi pemasangan sambungan; - Verfifikasi persiapan pengelasan; - Pemeriksaan hasil las serta verifikasi

hasil uji tanpa merusak; - Pengukuran dimensi bejana dan

pemeriksaan internal; - Uji bocor dan uji tekan; - Verifikasi formulir pemanufaktur dan

plat nama nejana.

B. INSPECTION FOR OCCUPATIONAL SAFETY OF THE PRESSURE VESSEL AND THE LIKE

The Technical Inspection of the pressure vessel and the like is distinguished into 3 (three) parts :

1. Pressure vessel and the like which are new

and / or will be installed. 2. Pressure vessel and the like which are

existing and / or have been installed. 3. Pressure vessel and the like which have

been repaired / altered / modified

B.1. Technical inspection of the pressure vessel and the like which are new and / or will be installed.

a. Review of data comprising :

- Pressure vessel calculation and construction drawing;

- Specifications of the materials which will be used;

- Specifications on welding procedures and procedure qualification record (form) as well as performance qualification record (certificate) of the welder / welding operator;

- Procedures for non destruction test and qualifications of its personnel;

- Procedures for repairs; - Post weld heat treatment procedures (if

required); - Pressure test procedures.

b. Physical inspection comprising :

- Verification of the manufacturer’s quality control system;

- Identification of the materials which will be used;

- Vessel forming verification; - Joint installation verification; - Welding preparation verification; - Inspection of the welding results as

well as verification of the non destruction test results;

- Vessel’s dimension measurement and internal inspection;

- Leak test and pressure test; - Verification of the manufacturer’s form

and vessel’s name plate.

WTCJ-02116 12 Decicion of the Director General of Petroleum and Gas No.84.K/38/DJM/1998

Page 13: Kep Dirjen Migas No-84-K 38 DJM 1998

c. Uji tekan - Pemeriksaan rekaman kalibrasi alat

pengukur dan alat pencatat tekanan, termasuk daerah jangkau yang diijinkan untuk tekanan uji yang bersangkutan, dimana skala penunjukan maksimum peralatan termaksud 1,5 – 4 kali tekanan uji.

- Uji tekan dilaksanakan dengan menaikkan tekanan secara bertahap dan dicatat dengan alat pencatat tekanan sampai tekanan uji yang telah ditentukan kemudian tekanan ditahan minimum 2 (dua) jam dan setelah itu tekanan dikeluarkan secara bertahap.

d. Pelaporan Menyusun seluruh hasil pemeriksaan teknis berbentuk dokumen untuk diserahkan ke Direktur Direktorat Teknik Pertambangan Minyak dan Gas Bumi sebagai bahan evaluasi untuk penerbitan Sertifikat Penggunaan Peralatan.

B.2. Pemeriksaan teknis bejana tekan dan sejenisnya yang lama dan atau telah dipasang.

a. Penelaahan data yang meliputi :

- Sertifikat kelayakan penggunaan peralatan yang akan diperpanjang masa berlakunya;

- Catatan riwayat penggunaan bejana; - Gambar bangunan bejana (as built

drawing) - Salinan plat nama atau marka keras

lainnya; - Prosedur kerja aman melakukan

pemeriksaan

b. Pemeriksaan fisik meliputui : - Pemeriksaan visual kondisi bejana; - Verifikasi hasil pengukuran terakhir

tebal bejana yang dilakukan oleh Perusahaan;

- Melakukan pengukuran tebal bejana; - Uji tidak merusak (bila diperlukan); - Verifikasi hasil perhitungn sisa umur

bejana.

c. Pressure test - Calibration record inspection of the

pressure gauge and pressure recorder including the allowed range area for the relevant pressure test where the maximum reading scale of the relevant equipment is 1.5 - 4 times test pressure.

- The pressure test is carried out by increasing the pressure step by step and is recorded by the pressure recording device until reaching the test pressure already stipulated, and then the pressure is retained for minimum 2 (two) hours and after that, the pressure is released out step by step

d. Reporting

To prepare all the technical inspection results in the form of documents to be submitted to the Director of the Directorate of Petroleum and Gas Mining Engineering as evaluation material for the issue of the Worthiness of Equipment Operation Certificate.

B.2. Technical inspection of the pressure vessel and the like which are existing and / or have been installed. a. Review of data comprising :

- Worthiness of equipment operation certificate of which the validity period will be extended;

- History record of the vessel operation;

- As built drawing of the vessel; - Copy of the name plate or other hard

marks; - Safe work procedures to carry out

the inspection.

b. Physical inspection comprising : - Visual inspection of the vessel’s

condition; - Verification of the last measurement

results of the vessel’s thickness carried out by the Company;

- To measure the vessel’s thickness; - Non-destruction Test (if required); - Verification of the calculation results

of the remaining vessel’s life.

WTCJ-02116 13 Decicion of the Director General of Petroleum and Gas No.84.K/38/DJM/1998

Page 14: Kep Dirjen Migas No-84-K 38 DJM 1998

c. Pelaporan Menyusun seluruh hasil pemeriksaan teknis berbentuk dokumen untuk diserahkan ke Direktur Direktorat Teknik Pertambangan Minyak dan Gas Bumi sebagai bahan evaluasi untuk menerbitkan Sertifikat Kelayakan Penggunaan Peralatan.

B.3. Pemeriksaan teknis bejana tekan dan

sejenisnya yang mengalami reparasi / alterasi / modifikasi.

a. Penelaahan data yang meliputi :

- Sertifikasi Kelayakan Penggunaan Peralatan yang akan diterbitkan dan atau diperpanjang masa berlakunya;

- Catatan riwayat penggunaan bejana - Gambar bangunan dan konstruksi

bejana; - Salinan plat nama atau marka keras

lainnya; - Prosedur kerja aman melakukan

pemeriksaan; - Prosedur reparasi / alterasi / modifikasi; - perhitungan reparasi / alterasi /

modifikasi; - Spesifikasi material bahan pengganti; - Spesifikasi prosedur las dan rekaman

kualifikasi prosedur serta catatan kualifikasi (sertifikat) unjuk kerja juru / operator las;

- Prosedur uji tidak merusak dan

kualifikasi personilnya; - Prosedur perlakuan panas pasca las (bila

dsyaratkan).

b. Pemeriksaan fisik meliputui : - Verifikasi sistem pengendalian mutu

pemanufaktir; - Identifikasi material yang akan

digunakan; - Verifikasi pembentukan bejana; - Verifikasi pemasangan sambungan; - Verifikasi persiapan pengelasan; - Pemeriksaan hasil las serta verifikasi uji

tanpa merusak; - Pengukuran dimensi bejana; - Uji bocor dan uji tekan (bila diperlukan)

c. Reporting To prepare all the technical inspection results in the form of documents to be submitted to the Director of the Directorate of Oil and Gas Mining Engineering as evaluation material for the issue of the Worthiness of Equipment Operation Certificate.

B.3. Technical inspection of the pressure vessel and the like which have been repaired / altered / modified.

a. Analysis of data comprising :

- Worthiness of equipment operation certificate which will be issued, or of which the validity period will be extended;

- History record of the vessel operation; - As built drawing and construction of

the vessel; - Copy of the name plate or other hard

marks; - Safe work procedures to carry out the

inspection. - Procedures for repaird / alteration /

modification; - Calculation of repairs / alteration /

modification; - Specifications of the substitute

materials; - Specifications on welding procedures

and procedure qualification record as well as performance qualification record (certificate) of the welder / welding operator;

- Procedures for non destructive test and qualifications of its personnel;

- Post weld heat treatment procedures (if required).

b. Physical inspection comprising :

- Verification of the manufacturer’s quality control system;

- Identification of the materials which will be used;

- Vessel forming verification; - Joint installation verification; - Welding preparation verification; - Inspection of the welding results as

well as verification of the non destructive test;

- Vessel’s dimension measurement; - Leak test and pressure test (if required);

WTCJ-02116 14 Decicion of the Director General of Petroleum and Gas No.84.K/38/DJM/1998

Page 15: Kep Dirjen Migas No-84-K 38 DJM 1998

- Verifikasi formulir pemanufaktur dan plat nama bejana;

- Verifikasi hasil pengukuran tebal bejana yang dilakukan oleh Perusahaan;

- Melakukan pengukuran tebal bejana - Verifikasi hasil perhitungan sisa umur

bejana

c. Pelaporan Menyusun seluruh hasil teknis berbentuk dokumen untuk diserahkan ke Direktur Direktorat Teknik Pertambangan Minyak dan Gas Bumi sebagai bahan evaluasi untuk penerbitkan Sertifikat Kelayakan Penggunaan Peralatan.

C. PEMERIKSAAN KESELAMATAN KERJA

PESAWAT ANGKAT

Pemeriksaan teknis pesawat angkat meliputi :

a. Penelaahan Dokumen • Spesifikasi perencanaan dan tabel beban • Perhitungan perencanaan • Gambar perencanaan • Material yang digunakan • Spesifikasi sambungan • Sumber tenaga yang digunakan • Petunjuk operasi (Operasi Manual)

b. Pemeriksaan fisik • Pemeriksaan sambungan-sambungan • Pemeriksaan kait pemegang beban • Pemeriksaan bagian yang bergerak serta

berputar • Pemeriksaan sistem hidrolik / pneumatik • Pemeriksaan kondisi tali baja (wire rope)

termasuk ikatan simpul dan jumlah lilitan

• Verifikasi fungsi indikator-indikator • Verifikasi dimensi boom • Verifikasi counter weight • Pemeriksaan persiapan pengujian

- Persiapan tempat pengujian - Prosedur pengujian - Persiapan alat uji antara lain :

- Alat ukur beban (load cell) - Beban uji - Alat-alat ukur lainnya

• Operator yang sudah berkualifikasi

- Verification of the manufacturer’s form and vessel’s name plate;

- Verification of the measurement results of the vessel’s thickness carried out by the Company;

- To measure the vessel’s thickness; - Verification of the calculation results of

the remaining vessel’s life.

c. Reporting To prepare all the technical inspection results in the form of documents to be submitted to the Director of the Directorate of Oil and Gas Mining Engineering as evaluation material for the issue of the Worthiness of Equipment Operation Certificate.

C. INSPECTION FOR OCCUPATIONAL SAFETY OF THE LIFTING EQUIPMENT /CRANE The technical inspection of the lifting equipment consists of : a. Review of Documents

• Design specifications and load table • Design calculation • Design drawing • Materials used • Specifications of joint • Source of energy used • Operating Manual

b. Physical Inspection

• Inspection of joints • Inspection of load holding hook • Inspection of moving as well as rotating

parts • Inspection of hydraulic / pneumatic system • Inspection of the condition of wire rope

including knot band and number of windings

• Verification of functions of the indicators • Verification of the boom’s dimension • Verification of counter weight • Test preparation inspection

- Test location preparation - Test procedures - Preparation of Test equipment among

others : - Load cell / measuring device - Test load - Other measuring devices

• Operator already having qualifications WTCJ-02116 15 Decicion of the Director General of Petroleum and Gas No.84.K/38/DJM/1998

Page 16: Kep Dirjen Migas No-84-K 38 DJM 1998

c. Pelaksanaan pengujian • Uji fungsi tanpa beban • Uji beban dengan prosedur uji beban yang

telah mendapat pengesahan Direktur

d. Pemeriksaan setelah pengujian Pemeriksaan atas seluruh bagian-baigan yang terbebani dan bergerak ataupun yang diam untuk mengetahui kemungkinan adanya deformasi, retak, longgar pada baut dan atau cacat-cacat lainnya.

e. Pemeriksaan khusus

- Apabila pesawat angkat mengalami kerusakan atau diragukan kemampuannya.

- Apabila diadakan perbaikan atau perubahan prinsipil pada pesawat angkat.

f. Rekaman hasil uji Rekaman hasil uji diisi berdasarkan atas data pesawat angkat dan hasil uji.

g. Pelaporan Menyusun seluruh hasil pemeriksaan teknis berbentuk dokumen untuk diserahkan ke Direktur Direktorat Teknik Pertambangan Minyak dan Gas Bumi sebagai bahan evaluasi untuk penerbitkan Sertifikat Kelayakan Penggunaan Peralatan.

D. PEMERIKSAAN KESELAMATAN KERJA UNIT POMPA, UNIT KOMPRESOR DAN PENGGERAKNYA.

Pemeriksaan teknis unit pompa, unit kompresor dan penggeraknya meliputi :

a. Penilaian terhadap rancang bangun unit

Pompa, unit Kompresor dan penggeraknya dengan melaksanakan penelaahan data : - Spesifikasi perencanaan; - Gambar dan perhitungan perencanaan; - Spesifikasi material yang digunakan; - Spesifikasi sambungan yang digunakan; - Spesifikasi komponen utama dan

pendukung serta piranti pengaman yang digunakan;

- Pedoman pengoperasian dan pemeliharaannya.

b. Penilaian fabrikasi dengan melaksanakan penelaahan laporan inspeksi yang dilakukan oleh Pihak Ketiga yang independen di pabrik pembuat yang terdiri dari antara lain :

c. Test implementation • Functional test with no load • Load test under load test procedures already

ratified by the Director

d. Inspection after test Inspection of all loaded and rotating or stationary parts to find out the possibility of any deformation, crack, lessen in bolts and / or other defects.

e. Special inspection - If the lifting equipment is damaged or its

ability is doubted. - If principal repairs or alterations are made

on the lifting equipment.

f. Test result form The test result form should be completed based on the lifting equipment data and test results.

g. Reporting

To prepare all the technical inspection results in the form of documents to be submitted to the Director of the Directorate of Oil and Gas Mining Engineering as evaluation material for the issue of the Worthiness of Equipment Operation Certificate.

D. INSPECTION FOR OCCUPATIONAL

SAFETY OF THE PUMP UNIT, COMPRESSOR UNIT AND THEIR DRIVE

The technical inspection of the pump unit, compressor unit and their drive includes :

a. Evaluation of the design of the Pump Unit,

Compressor Unit and their drive by performing a data analysis of : - Design specifications; - Design calculation and drawing; - Specifications of the materials used; - Specifications of the joints used; - Specifications of the main and supporting

components as well as safety appliances used;

- Their operating and maintenance Manuals.

b. Evaluation of fabrication by making an analysis of the report on inspection carried out by the independent third party in the manufacturer’s factory consisting among others of :

WTCJ-02116 16 Decicion of the Director General of Petroleum and Gas No.84.K/38/DJM/1998

Page 17: Kep Dirjen Migas No-84-K 38 DJM 1998

- Identifikasi material - Verifikasi pipa-pipa instrumen - Verifikasi pengujian komponen-komponen

utama; - Hasil uji balans - Hasil pemeriksaan kelurusan (alignment)

kopling dan poros pompa/kompresor dengan penggeraknya;

- Hasil “factory acceptance test” yang telah dilakukan dipabrik pembuat;

- Pemeriksaan terhadap sistem

penggeraknya.

c. Pemeriksaan fisik, yaitu pemeriksaan mengikuti proes pemasangan unit Pompa / unit Kompresor dengan penggeraknya dilokasi pemasangan dengan melakukan : - Identifikasi peralatan dan komponen; - Pemeriksaan kondisi struktur pondasi - Pemeriksaan kelengkapan alat ukur dan

piranti pengaman; - Pemeriksaan umum kondisi pemasangan

unit Pompa / unit Kompresor dan penggeraknya;

- Uji mekanikal, kelistrikan dan instrumen; - Uji coba piranti pengaman - Pemeriksaan pelaksanaan “start – up”; - Uji kemampuan.

d. Pelaporan

Menyusun seluruh hasil teknis berbentuk dokcumen untuk untuk diserahkan ke Direktur Direktorat Teknik Pertambangan Minyak dan Gas Bumi sebagai bahan evaluasi untuk penerbitan Sertifikat Kelayakan Penggunaan Peralatan.

E. PEMERIKSAAN KESELAMATAN KERJA PIPA PENYALUR

Pemeriksaan teknis pipa penyalur meliputi : a. Penelaahan Dokumen

- Umum • Lokasi • Jadwal penyelesaian pembangunan • Spesifikasi perencanaan • Spesifikasi prosedur las dan rekaman

kualifikasi prosedur serta catatan kualifikasi (sertifikat) unjuk kerja juru / operator las

- Identification of materials - Verification of instrument pipes - Verification of the test of main components - Balance test results - Alignment inspection results of the

coupling and shaft of the pump / compressor with their drive;

- Results of the factory acceptance test already carried out in the manufacturer’s factory;

- Inspection of the driving system.

c. Physical inspection, that is an inspection following the installation process of the Pump unit / Compressor unit with their drive in the installation location by performing : - Identification of equipment and

components; - Inspection of the foundation structure’s

condition - Inspection for completeness of the

measuring device and safety appliances - General inspection of the installation

condition of the Pump unit / Compressor unit with their drive;

- Mechanical, electrical and instrument test; - Safety device trial test - Inspection of the start up implementation - Performance test.

d. Reporting

To prepare (compile) all the technical inspection results in the form of documents to be submitted to the Director of the Directorate of Petroleum and Gas Mining Engineering as evaluation material for the issue of the Worthiness of Equipment Operation Certificate.

E. INSPECTION FOR OCCUPATIONAL

SAFETY OF THE PIPELINE.

The technical inspection of the pipeline includes : a. Review of Documents

- General • Location • Construction completion schedule • Design specifications • Specifications on welding procedures

and qualification record of procedures as well as performance qualification certificate of the welder / welding operator

WTCJ-02116 17 Decicion of the Director General of Petroleum and Gas No.84.K/38/DJM/1998

Page 18: Kep Dirjen Migas No-84-K 38 DJM 1998

• Prosedur reparasi • Spesifikasi material yang digunakan • Prosedur pengoperasian dan pemeliharaan • Prosedur pembersihan dan pengeringan • Data piranti pengaman.

- Rancang bangun • Penelaahan peta jalur bentang pipa

penyalur antara lain : * Kedalaman letak pipa penyalur

maksimum dan minimum (khusus pipa penyalur lepas pantai)

* Sudut kemiringan * Kedalaman perparitan * Jarak bentangan maksimum yang

tersangga * Right of Way (ROW).

• Penelaahan metode pelengkungan pipa di

lokasi meliputi : * Diameter pipa * Ketebalan pipa * Radius lengkung pipa

• Penelaahan beban pipa penyalur

* Beban operasi antara lain berat sendiri, tekanan internal dan eksternal, ekspansi panas, daya apung dan lain-lain.

*Beban lingkungan antara lain gelombang, arus, angin, gempa dan lain-lain.

* Beban pemasangan antara lain buckling, residual stress yang terjadi saat instalasi pipa.

• Penelaahan perhitungan kekuatan pipa

penyalur antara lain : * Tegangan yang terjadi pada pipa

penyalur, buckling on buttom stability (khusus pipa penyalur lepas pantai)

* Perhitungan penyangga pipa penyalur *Perhitungan tekanan uji yang akan

dilakukan

• Penelaahan perhitungan pengendalian korosi antara lain : * Karakteristik korosi * Metode pengendalian korosi * Spesifikasi dan dimensi coating * Kebutuhan pengendalian korosi yang

diperlukan

• Penelaahan pada spesifikasi terkait dan sitem intrumentasi antara lain :

• Procedures for repairs • Specifications of the materials used • Procedures for operation and

maintenance • Cleaning and drying procedures • Safety device data

- Design

• Review of the pipeline route map, i.e :

* Depth of the max. and min. pipeline location (especially offshore pipeline)

* Slope angle * Depth of ditches * Maximum range distance supported * Right of Way (ROW).

• Review of the pipe curving method in

the location consisting of : * Diameter of the pipe * Thickness of the pipe * Curving radius of the pipe

• Review of the pipeline’s load

* Operational load i.e own weight, internal and external pressure, heat expansion, floating capacity etc

* Surrounding load i.e wave, current, wind, earthquake, etc.

* Installation load i.e buckling, residual stress taking place at the time of the pipe installation

• Review of the pipeline’s strength calculation, i.e : *Tension taking place on the pipeline,

buckling on bottom stability (especially offshore pipeline)

* Calculation of the pipeline’s support * Calculation of the test pressure which

will be carried out

• Review of the corrosion control calculation, i.e : * Characteristics of corrosion * Corrosion control method *Coating specifications and dimensions * Corrosion control requirement

• Review of the related specifications and

instrumentation system, i.e :

WTCJ-02116 18 Decicion of the Director General of Petroleum and Gas No.84.K/38/DJM/1998

Page 19: Kep Dirjen Migas No-84-K 38 DJM 1998

* Sistem pipa terkait seperti riser, pig launcher, pig receiver, sistem metering dan lain-lain

* Stasiun penguat * Sistem instrumentasi seperti sistem

penghentian darurat, katup pengaman, dan lain-lain

* Jarak bentangan maksimum yang tersangga

• Penelaahan surat persetujuan atau

rekomendasi dari instansi yang berwenang untuk program pengolahan dan pemantauan lindungan lingkungan .

- Penelaahan data rencana operasi • Penggunaan (service) • Specific grafity • Tekanan normal masuk • Tekanan normal keluar • Tekanan operasi maksimum • Temperatur operasi • Laju aliran operasi

b. Pemeriksaan Fisik :

- Identifikasi material yang digunakan; - Pemeriksaan lokasi jalur pipa penyalur

untuk memastikan klasifikasi area, tipe konstruksi dan jarak aman yang tersedia;

- Pemeriksaan persiapan pengelasan dan kesamaan sumbu serta kelurusan sambungan pipa;

- Pemeriksaan sistem penyangga dan perparitan;

- Penelaahan hasil uji tidak merusak; - Kondisi dan rekaman hasil uji sistem

pengendalian korosi serta pemberat pipa (khusus pipa penyalur lepas pantai);

- Pemeriksaan pelaksanaan pembersihan dan pengeringan dalam pipa penyalur;

- Pemeriksaan kelengkapan piranti pengaman.

c. Pemeriksaan pelaksanaan uji tekan.

Kelengkapan peralatan uji yang terdiri dari :

- Dead weight tester (DWT) - Pengukur tekanan - Pengukur temperatur - Pencatat tekanan (pressure recorder) - Pencatata temperatur (temperatur recorder) - Pompa

* Related pipe systems such as riser, pig launcher, pig receiver, metering system etc

* Reinforcing station * Instrumentation system such as

emergency shut-down system, safety valve etc

* Maximum range distance supported

• Review of the approval letter or

recommendation from the competent authorities for the environmental protection monitoring and treatment program. - Review of the operational plan data

• Use (service) • Specific gravity • Normal pressure input • Normal pressure output • Maximum operation pressure • Operation temperature • Operation flow rate

b. Physical Inspection :

- Identification of the materials used; - Inspection of the pipeline route location to

ascertain the area classification, type of construction and safe distance available;

- Inspection of the welding arrangements and similarity of shafts as well as alignment of the pipe joints;

- Inspection of the support system and ditches;

- Review of the non destructive test results; - Condition and record of the test results of

corrosion control system and pipe weight (especially offshore pipeline);

- Inspection of the cleaning and drying implementation in the pipeline;

- Inspection for completeness of the safety devices.

c. Inspection of the pressure test implementation,

Inspection for completeness of the test equipment consisting of :

- Dead weight tester (DWT) - Pressure gauge - Temperature gauge - Pressure recorder - Temperature recorder - Pump

WTCJ-02116 19 Decicion of the Director General of Petroleum and Gas No.84.K/38/DJM/1998

Page 20: Kep Dirjen Migas No-84-K 38 DJM 1998

Alat pengukur dan pencatat tersebut harus dikalibrasi sebelum digunakan, dan skala penunjukkan maksimumnya adalah 1,5 – 4 kali tekanan uji.

d. Uji tekan Uji tekan dilaksanakan dengan menaikkan tekanan secara bertahap sampai dengan tekanan uji dan ditahan minimum selama 24 (dua puluh empat) jam untuk pipa penyalur di darat, minimum 8 (delapan) jam untuk pipa penyalur di lepas pantai dan minimum 2 (dua) jam untuk pipa penyalur uap panasbumi.

e. Pelaporan

Menyusun seluruh hasil teknis berbentuk dokcumen untuk untuk diserahkan ke Direktur Direktorat Teknik Pertambangan Minyak dan Gas Bumi sebagai bahan evaluasi untuk penerbitan Sertifikat Kelayakan Penggunaan Peralatan.

PEMERIKSAAN KESELAMATAN KERJA UNIT POWER GENERATOR, UNIT TRANSFORMER, UNIT SWITCHERGEAR DAN UNIT MOTOR CONTROL CENTER

Pemeriksaan teknis peralatan listrik meliputi :

a. Penelaahan Dokumen • Standar yang digunakan; • Spesifikasi unit peralatan listrik / data

sheet (Generator, Transformer, Switchgear dan Motor Control Center);

• Gambar perencanaan; • Spesifikasi perencanaan & konstruksi • Spesifikasi material; • Perhitungan perencanaan (bila

disyaratkan); • Prosedur pengoperasian & pemeliharaan; • Klasifikasi area; • Piranti pengaman; • Klas isolasi

b. Pemeriksaan fisik meliputi : • Pemeriksaan peralatan dan komponennya • Verifikasi plat nama • Pemeriksaan umum kondisi pemasangan di

lokasi • Pemeriksaan lay out peralatan dan area

klasifikasi

Those gauges and recorders shall be calibrated before being employed and the maximum reading scale shall be 1.5 - 4 times test pressure.

d. Pressure Test The pressure test is carried out by increasing the pressure in phases until reaching the test pressure, and is retained for minimum 24 (twenty four) hours for the onshore pipeline, minimum 8 (eight) hours for the offshore pipeline and minimum 2 (two) hours for the geothermal pipeline.

e. Reporting

To prepare (compile) all the technical inspection results in the form of documents to be submitted to the Director of the Directorate of Petroleum and Gas Mining Engineering as evaluation material for the issue of the Worthiness of Equipment Operation Certificate.

F. INSPECTION FOR OCCUPATIONAL

SAFETY OF THE POWER GENERATOR UNIT, TRANSFORMER UNIT, SWITCH GEAR UNIT AND MOTOR CONTROL CENTER UNIT

The technical inspection of the electrical

equipment consists of : a. Review of Documents • Standard applied; • Specifications of the electrical equipment

unit / data sheet (Generator, Transformer, Switch Gear and Motor Control Center);

• Design drawing; • Construction & design specifications; • Specifications of materials; • Design calculation (if required); • Procedures for operation & maintenance; • Area classification; • Safety applieances; • Insulation grade.

b. The physical inspection comprises :

• Inspection of equipment and its components

• Name plate verification • General inspection of the installation

condition in the location • Inspection of the equipment layout and area

classification

WTCJ-02116 20 Decicion of the Director General of Petroleum and Gas No.84.K/38/DJM/1998

Page 21: Kep Dirjen Migas No-84-K 38 DJM 1998

WTCJ-02116 21 Decicion of the Director General of Petroleum and Gas No.84.K/38/DJM/1998

• Pemeriksaan panel kendali • Pemeriksaaan terminal kabel utama dan

penetralan

c. Pengujian meliputi : • Pengujian ketahanan isolasi • Pengujian panel kendali • Pengujian Hi-pot kabel • Setting relay pengaman • Pengujian sinkronisasi • Pengujian automatic start unit emergency • Pengujian tanpa beban dan dengan beban • Penilaian penerimaan (test value) • Pre-commissioning dan commissioning

d. Pelaporan

Menyusun seluruh hasil teknis berbentuk dokcumen untuk untuk diserahkan ke Direktur Direktorat Teknik Pertambangan Minyak dan Gas Bumi sebagai bahan evaluasi untuk penerbitan Sertifikat Kelayakan Penggunaan Peralatan.

Ditetapkan di Jakarta Pada tanggal, 19 Agustus 1998 Direktur Jenderal Minyak dan Gas Bumi Soepraptono Soeleiman

• Inspection of control panel • Inspection of main wire terminal and

neutralization

c. The tests consist of : • Insulation resistance test • Control panel test • Wire Hi-pot test • Safety relay setting • Synchronization test • Automatic start test of the emergency unit • Test with no load and with load • Acceptance evaluation (test value) • Pre-commissioning and commissioning

d. Reporting

To prepare all the technical inspection results in the form of documents to be submitted to the Director of the Directorate of Oil and Gas Mining Engineering as evaluation material for the issue of the Worthiness of Equipment Operation Certificate.

Stipulated in Jakarta On 19th August 1998 The Director General of Oil and Gas

Soepraptono Soeleiman

Translated from Bahasa Indonesia into English by Catharina Chiandra Sworn & Authorized Translator by Decree No. 1715 Th. 2000 of the Governor of DKI Jakarta

Jakarta, 12 April 2002