www.klinger.co.at

KLINGERSIL® C-4106KLINGERSIL® C-4106 is a special gasket for a wide range of industrial applications. It is also suitable for the use with low bolt loads.

Synthetic fibres and cork, bonded with NBR.This sealing material shows an excellent conformity at low sur-face pressure.

referring to KLINGERSIL® product range

» High compressibility » Use of the natural properties of cork » Dimensionally stable

Key features:

» Provides excellent adaptability to any sealing surface » Conforms easily » Excellent sealing at low stress

Benefits:

Properties:

Industries:

SUPERIOR

EXCELLENT

VERY GOOD

GOOD

MODERATE

MECHANICALRESISTANCE

THERMALRESISTANCE

SEALABILITY CHEMICALRESISTANCE

TRANSPORTOIL & GAS INFRASTRUCTUREENERGYINDUSTRY CHEMICAL PULP & PAPER FOOD & BEVERAGES

PHARMA

Not available

Certificates and approvals:

www.klinger.co.at

Compressibility ASTM F 36 J % 30

Recovery ASTM F 36 J % 50

Stress relaxation DIN 52913 25 MPa, 16 h/100°C MPa 15

KLINGER cold/hot compression thickness decrease at 23°C % 16

25 MPa thickness decrease at 200°C % 28

Tightness DIN 28090-2 mg/s x m 0.01

Thickness increase after fluid oil IRM 903: 5 h/150°C % 5

immersion ASTM F 146 fuel B: 5 h/23°C % 7

Density g/cm3 1.0

pT diagram for thickness 2.0 mm:

Typical technical data for thickness 2.0 mm:

Certified acc. to DIN EN ISO 9001:2008 Subject to technical alterations. Status: March 2016

Rich. Klinger Dichtungstechnik GmbH & Co KG » Am Kanal 8-10 » A-2352 Gumpoldskirchen, AustriaTel +43 (0) 2252/62599-137 » Fax +43 (0) 2252/62599-296 » e-mail: marketing@klinger.co.at

1000 x 1500 mm, 2000 x 1500 mm

0.5 mm, 1.0 mm, 1.5 mm, 2.0 mm, 3.0 mm

Thicknesses:

Thickness acc. DIN 28091-1Length 50 mm, width 50 mm

Other thicknesses, sizes and tolerances on request.

Tolerances:

Dimensions of the standard sheets:

Sizes:

In area one, the gasket material is normally sui-table subject to chemical compatibility.

In area two, the gasket material may be suitable but a technical evaluation is recommended.

In area three, do not in- stall the gasket without a technical evaluation.

Always refer to the che-mical resistance of the gasket to the media.

2 31

-2000

20

30

40

50

60

70

80

90

100

0°C 100 200 300 400-100

pib

ar

-2000

20

30

40

50

60

70

80

90

100

0°C 100 200 300 400-100

pib

ar

-2000

20

30

40

50

60

70

80

90

100

0°C 100 200 300 400-100

pib

ar

3

2 1

3

2 1

3

2 1

www.klinger.co.at

KLINGERSIL® C4265KLINGERSIL® C-4265 is a gasket for liquids and gase-ous media at lower pressures, temperatures and low bolt loads. It offers a good resistance to oils, hydrocarbons, refrigerants and other chemicals and shows an excellent conformity with the flanges at low surface loads.

Mineral fibres bonded with NBR. Suitable for a wide range of applications including oils, sol-vents, steam and gases. Excellent conformity with the flanges at low surface loads.

» High compressibility » Excellent spring back behavior » Resistant to creep and cold flow » Dimensionally stable » Consistent material composition

Key features:

» Provides superior adaptability to any sealing surface » Seals irregular flanges » Conforms easily » Excellent sealing at low stress » Increased resistance against refrigerants

Benefits:

Properties:

Industries:

SUPERIOR

EXCELLENT

VERY GOOD

GOOD

MODERATE

MECHANICALRESISTANCE

THERMALRESISTANCE

SEALABILITY CHEMICALRESISTANCE

TRANSPORTPULP & PAPEROIL & GASCHEMICAL INFRASTRUCTUREENERGYINDUSTRY FOOD & BEVERAGES

referring to KLINGERSIL® product range

PHARMA

» TA-Luft (Clean Air)

Certificates and approvals:

www.klinger.co.at

Compressibility ASTM F 36 J % 26

Recovery ASTM F 36 J % 50

KLINGER cold/hot compression thickness decrease at 23°C % 18

50 MPa thickness decrease at 200°C % 22

Tightness DIN 28090-2 mg/s x m 0.01

Specific leakrate λ VDI 2440 mbar x l/s x m 5.3E-09

Thickness increase after fluid oil IRM 903: 5 h/150°C % 10

immersion ASTM F 146 fuel B: 5 h/23°C % 15

Density g/cm3 1.6

ASME-Code sealing factors

for gasket thickness 1.0 mm tightness class 0.1mg/s x m MPa y 10

m 1.0

for gasket thickness 2.0 mm tightness class 0.1mg/s x m MPa y 10

m 2.9

for gasket thickness 3.0 mm tightness class 0.1mg/s x m MPa y 10

m 3.3

pT diagram for thickness 2.0 mm:

Typical technical data for thickness 2.0 mm:

Certified acc. to DIN EN ISO 9001:2008 Subject to technical alterations. Status: March 2016

Rich. Klinger Dichtungstechnik GmbH & Co KG » Am Kanal 8-10 » A-2352 Gumpoldskirchen, AustriaTel +43 (0) 2252/62599-137 » Fax +43 (0) 2252/62599-296 » e-mail: marketing@klinger.co.at

1500 x 2000 mm

0.5 mm, 0.8 mm, 1.0 mm, 1.5 mm

Thicknesses:

Thickness acc. DIN 28091-1Length 50 mm, width 50 mm

Other thicknesses, sizes and tolerances on request.

Tolerances:

Dimensions of the standard sheets:

Sizes:

In area one, the gasket material is normally sui-table subject to chemical compatibility.

In area two, the gasket material may be suitable but a technical evaluation is recommended.

In area three, do not in-stall the gasket without a technical evaluation.

Always refer to the che-mical resistance of the gasket to the media.

2 31

-2000

20

30

40

50

60

70

80

90

100

0°C 100 200 300 400-100

pib

ar

-2000

20

30

40

50

60

70

80

90

100

0°C 100 200 300 400-100

pib

ar

-2000

20

30

40

50

60

70

80

90

100

0°C 100 200 300 400-100

pib

ar

3

2

1

3

2

1

3

2

1

www.klinger.co.at

KLINGERSIL® C-4300KLINGERSIL® C-4300 is a universal high-pressure gasket and offers more safety for a wide range of suitable appli-cations.

Aramid fibres bonded with NBR.Resistant to hot water, steam, oils, hydrocarbons and many other chemicals.

» General purpose gasket material » Dimensionally stable » Consistent material composition

Key features:

» Excellent price/performance ratio » Suitable for many different media

Benefits:

Properties:

Industries:

SUPERIOR

EXCELLENT

VERY GOOD

GOOD

MODERATE

MECHANICALRESISTANCE

THERMALRESISTANCE

SEALABILITY CHEMICALRESISTANCE

TRANSPORTPULP & PAPEROIL & GASCHEMICAL INFRASTRUCTUREENERGYINDUSTRY FOOD & BEVERAGES

referring to KLINGERSIL® product range

PHARMA

» DIN-DVGW » DIN-DVGW W 270 » Elastomer-Guideline » German Lloyd » SVGW approval

Certificates and approvals:

www.klinger.co.at

Compressibility ASTM F 36 J % 14

Recovery ASTM F 36 J % 50

Stress relaxation DIN 52913 50 MPa,16 h/175°C MPa 32

50 MPa,16 h/300°C MPa 20

Stress relaxation BS 7531 40 MPa, 16 h/300°C MPa 23

KLINGER cold/hot compression thickness decrease at 23°C % 10

50 MPa thickness decrease at 300°C % 22

Tightness DIN 28090-2 mg/s x m 0.03

Thickness increase after fluid oil IRM 903: 5 h/150°C % 5

immersion ASTM F 146 fuel B: 5 h/23°C % 10

Density g/cm3 1.6

Average surface resistance ρO Ω 2.2x10E12

Average specific volume resistance ρD Ω cm 1.2x10E12

Average dielectric strength Ed kV/mm 10

Average power factor 50 Hz tan δ 0.082

Average dielectric coefficient 50 Hz εr 7.4

Thermal conductivity λ W/mK 0.39

Classification acc. to BS 7531:2006 Grade Y

ASME-Code sealing factors

for gasket thickness 1.0 mm tightness class 0.1 mg/s x m MPa y 15

m 1.3

for gasket thickness 2.0 mm tightness class 0.1 mg/s x m MPa y 15

m 3.0

for gasket thickness 3.0 mm tightness class 0.1 mg/s x m MPa y 15

m 4.0

pT diagram for thickness 2.0 mm:

Typical technical data for thickness 2.0 mm:

Certified acc. to DIN EN ISO 9001:2008 Subject to technical alterations. Status: March 2016

Rich. Klinger Dichtungstechnik GmbH & Co KG » Am Kanal 8-10 » A-2352 Gumpoldskirchen, AustriaTel +43 (0) 2252/62599-137 » Fax +43 (0) 2252/62599-296 » e-mail: marketing@klinger.co.at

1000 x 1500 mm, 2000 x 1500 mm

0.5 mm, 1.0 mm, 1.5 mm, 2.0 mm, 3.0 mm

Thicknesses:

Thickness acc. DIN 28091-1Length 50 mm, width 50 mm

Other thicknesses, sizes and tolerances on request.

Tolerances:

Dimensions of the standard sheets:

Sizes:

In area one, the gasket material is normally sui-table subject to chemical compatibility.

In area two, the gasket material may be suitable but a technical evaluation is recommended.

In area three, do not in-stall the gasket without a technical evaluation.

Always refer to the che-mical resistance of the gasket to the media.

2 31

KLINGERSIL® C-4300 / 3mmKLINGERSIL® C-4300 / 2mmKLINGERSIL® C-4300 / 1mm

-2000

20

30

40

50

60

70

80

90

100

0°C 100 200 300 400-100

pib

ar

-2000

20

30

40

50

60

70

80

90

100

0°C 100 200 300 400-100

pib

ar

-2000

20

30

40

50

60

70

80

90

100

0°C 100 200 300 400-100

pib

ar

32

1

3

2

1

3

2

1

www.klinger.co.at

KLINGERSIL® C-4324KLINGERSIL® C-4324 is a universal high-pressure gasket, suitable for a wide range of applications.

Combination of synthetic high performance fibres, bonded with NBR.This gasket material is suitable for the use in liquids and steam at lower pressure and temperature. Resistant to water, oils, hydrocarbons and many other chemicals.

» General purpose gasket material » Dimensionally stable » Consistent material composition

» DIN-DVGW » Elastomer-Guideline » WRAS approval » German Lloyd » SVGW approval

Key features:

» Excellent price/performance ratio » Suitable for many different media

Benefits:

Properties:

Industries:

SUPERIOR

EXCELLENT

VERY GOOD

GOOD

MODERATE

MECHANICALRESISTANCE

THERMALRESISTANCE

SEALABILITY CHEMICALRESISTANCE

Certificates and approvals:

TRANSPORTPULP & PAPEROIL & GASCHEMICAL INFRASTRUCTUREENERGYINDUSTRY FOOD & BEVERAGES

referring to KLINGERSIL® product range

PHARMA

www.klinger.co.at

pT diagram for thickness 2.0 mm:

Typical technical data for thickness 2.0 mm:

Certified acc. to DIN EN ISO 9001:2008 Subject to technical alterations. Status: March 2016

Rich. Klinger Dichtungstechnik GmbH & Co KG » Am Kanal 8-10 » A-2352 Gumpoldskirchen, AustriaTel +43 (0) 2252/62599-137 » Fax +43 (0) 2252/62599-296 » e-mail: marketing@klinger.co.at

1000 x 1500 mm, 2000 x 1500 mm

0.5 mm, 1.0 mm, 1.5 mm, 2.0 mm

Thicknesses:

Thickness acc. DIN 28091-1Length 50 mm, width 50 mm

Other thicknesses, sizes and tolerances on request.

Tolerances:

Dimensions of the standard sheets:

Sizes:

2 31

In area one, the gasket material is normally sui-table subject to chemical compatibility.

In area two, the gasket material may be suitable but a technical evaluation is recommended.

In area three, do not in-stall the gasket without a technical evaluation.

Always refer to the che-mical resistance of the gasket to the media.

Compressibility ASTM F 36 J % 10

Recovery ASTM F 36 J % 55

Stress relaxation DIN 52913 50 MPa,16 h/175°C MPa 31

50 MPa, 16 h/300°C MPa 20

Stress relaxation BS 7531 40 MPa, 16 h/300°C MPa 23

KLINGER cold/hot compression thickness decrease at 23°C % 10

50 MPa thickness decrease at 300°C % 25

Tightness DIN 28090-2 mg/s x m 0.03

Thickness increase after fluid oil IRM 903: 5 h/150°C % 5

immersion ASTM F 146 fuel B: 5 h/23°C % 10

Density g/cm3 1.85

Average surface resistance ρO Ω 1.04x10E13

Average specific volume resistance ρD Ω cm 4.3x10E11

Average dielectric strength Ed kV/mm 12

Average power factor 50 Hz tan δ 0.109

Average dielectric coefficient 50 Hz εr 9

Thermal conductivity λ W/mK 0.50

Classification acc. to BS 7531:2006 Grade Y

ASME-Code sealing factors

for gasket thickness 1.0 mm tightness class 0.1 mg/s x m MPa y 15

m 2.2

for gasket thickness 2.0 mm tightness class 0.1 mg/s x m MPa y 15

m 2.6

for gasket thickness 3.0 mm tightness class 0.1 mg/s x m MPa y 15

m 4.1

-2000

20

30

40

50

60

70

80

90

100

0°C 100 200 300 400-100

pib

ar

-2000

20

30

40

50

60

70

80

90

100

0°C 100 200 300 400-100

pib

ar

-2000

20

30

40

50

60

70

80

90

100

0°C 100 200 300 400-100

pib

ar

32

1

3

2

1

3

2 1

www.klinger.co.at

KLINGERSIL® C-4400KLINGERSIL® C-4400 is a universal material for safe and reliable sealing. It consists of a unique matrix, which of-fers an excellent combination of different properties.

Aramid fibres bonded with NBR.Resistant to oils, water, steam, gases, salt solutions, fuels, alcohols, moderate organic and inorganic acids, hydrocar-bons, lubricants and refrigerants.

» Universal high pressure gasket material » Dimensionally stable » Consistent material composition

Key features:

» Excellent price/performance ratio » Suitable for many different media » Very good resistance to refrigerants

Benefits:

Properties:

Industries:

SUPERIOR

EXCELLENT

VERY GOOD

GOOD

MODERATE

MECHANICALRESISTANCE

THERMALRESISTANCE

SEALABILITY CHEMICALRESISTANCE

TRANSPORTPULP & PAPEROIL & GASCHEMICAL INFRASTRUCTUREENERGYINDUSTRY FOOD & BEVERAGES

referring to KLINGERSIL® product range

PHARMA

» BAM-tested » DIN-DVGW » DIN-DVGW W 270 » DVGW VP 401 » Elastomer-Guideline » ÖVGW » German Lloyd » TA-Luft (Clean air) » Fire-Safe acc. DIN EN ISO 10497

Certificates and approvals:

www.klinger.co.at

pT diagram for thickness 2.0 mm:

Typical technical data for thickness 2.0 mm:

Certified acc. to DIN EN ISO 9001:2008 Subject to technical alterations. Status: March 2016

Rich. Klinger Dichtungstechnik GmbH & Co KG » Am Kanal 8-10 » A-2352 Gumpoldskirchen, AustriaTel +43 (0) 2252/62599-137 » Fax +43 (0) 2252/62599-296 » e-mail: marketing@klinger.co.at

1000 x 1500 mm, 2000 x 1500 mm

0.5 mm, 1.0 mm, 1.5 mm, 2.0 mm, 3.0 mm

Thicknesses:

Thickness acc. DIN 28091-1Length 50 mm, width 50 mm

Other thicknesses, sizes and tolerances on request.

Tolerances:

Dimensions of the standard sheets:

Sizes:

2 31

-2000

20

30

40

50

60

70

80

90

100

0°C 100 200 300 400-100

pib

ar

-2000

20

30

40

50

60

70

80

90

100

0°C 100 200 300 400-100

pib

ar

-2000

20

30

40

50

60

70

80

90

100

0°C 100 200 300 400-100

pib

ar

3

2

1

3

2

1

3

2

1

-2000

20

30

40

50

60

70

80

90

100

0°C 100 200 300 400-100

pib

ar

-2000

20

30

40

50

60

70

80

90

100

0°C 100 200 300 400-100

pib

ar

-2000

20

30

40

50

60

70

80

90

100

0°C 100 200 300 400-100

pib

ar

3

2

1

3

2

1

3

2

1

In area one, the gasket material is normally sui-table subject to chemical compatibility.

In area two, the gasket material may be suitable but a technical evaluation is recommended.

In area three, do not in-stall the gasket without a technical evaluation.

Always refer to the che-mical resistance of the gasket to the media.

Compressibility ASTM F 36 J % 11

Recovery ASTM F 36 J % 55

Stress relaxation DIN 52913 50 MPa, 16 h/175°C MPa 37

50 MPa, 16 h/300°C MPa 25

Stress relaxation BS 7531 40 MPa, 16 h/300°C MPa 25

KLINGER cold/hot compression thickness decrease at 23°C % 10

50 MPa thickness decrease at 300°C % 20

Tightness DIN 28090-2 mg/s x m 0.02

Specific leakrate λ VDI 2440 mbar x l/s x m 1.64E-08

Thickness increase after fluid oil IRM 903: 5 h/150°C % 3

immersion ASTM F 146 fuel B: 5 h/23°C % 5

Density g/cm3 1.6

Average surface resistance ρO Ω 1.4x10E12

Average specific volume resistance ρD Ω cm 1.2x10E12

Average dielectric strength Ed kV/mm 21.6

Average power factor 50 Hz tan δ 0.131

Average dielectric coefficient 50 Hz εr 9.2

Thermal conductivity λ W/mK 0.42

Classification acc. to BS 7531:2006 Grade AY

ASME-Code sealing factors

for gasket thickness 1.0 mm tightness class 0.1mg/s x m MPa y 15

m 1.2

for gasket thickness 2.0 mm tightness class 0.1mg/s x m MPa y 15

m 1.6

for gasket thickness 3.0 mm tightness class 0.1mg/s x m MPa y 15

m 4.0

www.klinger.co.at

KLINGERSIL® C-4408KLINGERSIL® C-4408 is suitable for high stress due to wire reinforcement. It is a universal high-pressure gasket for the use in a wide range of industrial applications.

Aramid fibres bonded with NBR.Resistant to oils, water, steam, gases, fuels, alcohols, hy-drocarbons, lubricants and refrigerants.

» Wire reinforcement » Improved stress relaxation

» German Lloyd

Key features:

» Suitable for higher pressures » Higher resistance against blow-outs » More safety at high internal pressures

Benefits:

Properties:

Industries:

SUPERIOR

EXCELLENT

VERY GOOD

GOOD

MODERATE

MECHANICALRESISTANCE

THERMALRESISTANCE

SEALABILITY CHEMICALRESISTANCE

Certificates and approvals:

TRANSPORTPULP & PAPEROIL & GASCHEMICAL ENERGYINDUSTRY

referring to KLINGERSIL® product range

INFRASTRUCTURE FOOD & BEVERAGES

PHARMA

www.klinger.co.at

Compressibility ASTM F 36 J % 8

Recovery ASTM F 36 J % 50

Stress relaxation DIN 52913 50 MPa, 16 h/300°C MPa 28

Stress relaxation BS 7531 40 MPa, 16 h/300°C MPa 28

KLINGER cold/hot compression thickness decrease at 23°C % 10

50 MPa thickness decrease at 300°C % 18

Thickness increase after fluid oil IRM 903: 5 h/150°C % 5

immersion ASTM F 146 fuel B: 5 h/23°C % 5

Density g/cm3 1.9

Classification acc. to BS 7531:2006 Grade Y

pT diagram for thickness 2.0 mm:

Typical technical data for thickness 2.0 mm:

Certified acc. to DIN EN ISO 9001:2008 Subject to technical alterations. Status: March 2016

Rich. Klinger Dichtungstechnik GmbH & Co KG » Am Kanal 8-10 » A-2352 Gumpoldskirchen, AustriaTel +43 (0) 2252/62599-137 » Fax +43 (0) 2252/62599-296 » e-mail: marketing@klinger.co.at

1000 x 1500 mm, 2000 x 1500 mm

0.5 mm, 1.0 mm, 1.5 mm, 2.0 mm, 3.0 mm

Thicknesses:

Thickness acc. DIN 28091-1Length 50 mm, width 50 mm

Other thicknesses, sizes and tolerances on request.

Tolerances:

Dimensions of the standard sheets:

Sizes:

2 31

In area one, the gasket material is normally sui-table subject to chemical compatibility.

In area two, the gasket material may be suitable but a technical evaluation is recommended.

In area three, do not in-stall the gasket without a technical evaluation.

Always refer to the che-mical resistance of the gasket to the media.

KLINGERSIL® C-4408 / 1mm KLINGERSIL® C-4408 / 2mm KLINGERSIL® C-4408 / 3mm

-2000

20

30

40

50

60

70

80

90

100

0°C 100 200 300 400-100

pib

ar

-2000

20

30

40

50

60

70

80

90

100

0°C 100 200 300 400-100

pib

ar

-2000

20

30

40

50

60

70

80

90

100

0°C 100 200 300 400-100

pib

ar

3

2

1

3

2

1

3

2 1

www.klinger.co.at

KLINGERSIL® C-4409KLINGERSIL® C-4409 offers more safety at high thermal and mechanical stress. Due to the expanded metal, this special high-pressure gasket is suitable for high loads.

Synthetic fibres bonded with NBR.Chemical resistance to oils, water, steam, hydrocarbons as well as to liquid and gaseous chemicals.

» Expanded metal reinforcement » Improved stress relaxation

» German Lloyd » TA-Luft (Clean air)

Key features:

» Suitable for higher pressures » Higher resistance against blow-outs » More safety at high internal pressures

Benefits:

Properties:

Industries:

SUPERIOR

EXCELLENT

VERY GOOD

GOOD

MODERATE

MECHANICALRESISTANCE

THERMALRESISTANCE

SEALABILITY CHEMICALRESISTANCE

Certificates and approvals:

TRANSPORTPULP & PAPEROIL & GASCHEMICAL ENERGYINDUSTRY

referring to KLINGERSIL® product range

INFRASTRUCTURE FOOD & BEVERAGES

PHARMA

www.klinger.co.at

pT diagram for thickness 1.5 mm:

Typical technical data for thickness 1.5 mm:

Certified acc. to DIN EN ISO 9001:2008 Subject to technical alterations. Status: March 2016

Rich. Klinger Dichtungstechnik GmbH & Co KG » Am Kanal 8-10 » A-2352 Gumpoldskirchen, AustriaTel +43 (0) 2252/62599-137 » Fax +43 (0) 2252/62599-296 » e-mail: marketing@klinger.co.at

Dimensions of the standard sheets:

2 31

-2000

20

30

40

50

60

70

80

90

100

0°C 100 200 300 400-100

pib

ar

3

2

1

-2000

20

30

40

50

60

70

80

90

100

0°C 100 200 300 400-100

pib

ar

3

2

1

-2000

20

30

40

50

60

70

80

90

100

0°C 100 200 300 400-100

pib

ar

3

2

1

In area one, the gasket material is normally sui-table subject to chemical compatibility.

In area two, the gasket material may be suitable but a technical evaluation is recommended.

In area three, do not in-stall the gasket without a technical evaluation.

Always refer to the che-mical resistance of the gasket to the media.

Compressibility ASTM F 36 J % 7

Recovery ASTM F 36 J % 50

Stress relaxation DIN 52913 50 MPa, 16 h/300°C MPa 35

Stress relaxation BS 7531 40 MPa, 16 h/300°C MPa 32

KLINGER cold/hot compression thickness decrease at 23°C % 10

50 MPa thickness decrease at 300°C % 10

Specific leakrate λ VDI 2440 mbar x l/s x m 5.2E-05

Thickness increase after fluid oil IRM 903: 5 h/150°C % 5

immersion ASTM F 146 fuel B: 5 h/23°C % 10

Density g/cm3 2.0

Classification acc. to BS 7531:2006 Grade Y

ASME-Code sealing factors

for gasket thickness 1.0 mm tightness class 0.1 mg/s x m MPa y 30

m 3.0

for gasket thickness 2.0 mm tightness class 0.1 mg/s x m MPa y 30

m 3.2

for gasket thickness 3.0 mm tightness class 0.1 mg/s x m MPa y 30

m 3.8

1000 x 1500 mm, 2000 x 1500 mm

1000 x 1230 mm, 2000 x 1230 mm

Sizes KLINGERSIL® C-4409 L:

Thickness acc. DIN 28091-1Length 50 mm, width 50 mm

Other thicknesses, sizes and tolerances on request.

Tolerances:Sizes KLINGERSIL® C-4409:

1.0 mm, 1.5 mm

Thicknesses:

www.klinger.co.at

KLINGERSIL® C-4430KLINGERSIL® C-4430 offers outstanding stress retention and resistance to hot water and steam.

Optimum combination of synthetic fibres, bonded with NBR.Resistant to water and steam at higher temperatures as well as to oils, gases, salt solutions, fuels, alcohols, moderate organic and inorganic acids, hydrocarbons, lubricants and refrigerants.

» Optimum combination of synthetic and glass fibres » Outstanding stress relaxation » Dimensionally stable

» BAM-tested » DIN-DVGW » DIN-DVGW W 270 » DVGW VP 401 » Elastomer-Guideline » WRAS approval » German Lloyd » TA-Luft (Clean air) » Fire-Safe acc. to DIN EN ISO 10497 » Fire-Safe acc. to ISO 19921

Key features:

» Suitable for high temperature steam and water » Better resistance against hydrocarbons » Suitable for many different media

Benefits:

Properties:

Industries:

SUPERIOR

EXCELLENT

VERY GOOD

GOOD

MODERATE

MECHANICALRESISTANCE

THERMALRESISTANCE

SEALABILITY CHEMICALRESISTANCE

Certificates and approvals:

TRANSPORTPULP & PAPEROIL & GASCHEMICAL INFRASTRUCTUREENERGYINDUSTRY FOOD & BEVERAGES

referring to KLINGERSIL® product range

PHARMA

www.klinger.co.at

pT diagram for thickness 2.0 mm:

Typical technical data for thickness 2.0 mm:

Certified acc. to DIN EN ISO 9001:2008 Subject to technical alterations. Status: March 2016

Rich. Klinger Dichtungstechnik GmbH & Co KG » Am Kanal 8-10 » A-2352 Gumpoldskirchen, AustriaTel +43 (0) 2252/62599-137 » Fax +43 (0) 2252/62599-296 » e-mail: marketing@klinger.co.at

1000 x 1500 mm, 2000 x 1500 mm

0.5 mm, 1.0 mm, 1.5 mm, 2.0 mm, 3.0 mm

Thicknesses:

Thickness acc. DIN 28091-1Length 50 mm, width 50 mm

Other thicknesses, sizes and tolerances on request.

Tolerances:

Dimensions of the standard sheets:

Sizes:

2 31

In area one, the gasket material is normally sui-table subject to chemical compatibility.

In area two, the gasket material may be suitable but a technical evaluation is recommended.

In area three, do not in-stall the gasket without a technical evaluation.

Always refer to the che-mical resistance of the gasket to the media.

Compressibility ASTM F 36 J % 9

Recovery ASTM F 36 J % 55

Stress relaxation DIN 52913 50 MPa, 16 h/175°C MPa 39

50 MPa, 16 h/300°C MPa 35

Stress relaxation BS 7531 40 MPa, 16 h/300°C MPa 31

KLINGER cold/hot compression thickness decrease at 23°C % 8

50 MPa thickness decrease at 300°C % 11

Tightness DIN 28090-2 mg/s x m 0.05

Specific leakrate λ VDI 2440 mbar x l/s x m 2.13E-05

Thickness increase after fluid oil IRM 903: 5 h/150°C % 3

immersion ASTM F 146 fuel B: 5 h/23°C % 5

Density g/cm3 1.8

Average surface resistance ρO Ω 4.1x10E13

Average specific volume resistance ρD Ω cm 4.5x10E12

Average dielectric strength Ed kV/mm 21.3

Average power factor 50 Hz tan δ 0.03

Average dielectric coefficient 50 Hz εr 6.7

Thermal conductivity λ W/mK 0.38

Classification acc. to BS 7531:2006 Grade AX

ASME-Code sealing factors

for gasket thickness 1.0 mm tightness class 0.1 mg/s x m MPa y 20

m 1.1

for gasket thickness 2.0 mm tightness class 0.1 mg/s x m MPa y 20

m 1.6

for gasket thickness 3.0 mm tightness class 0.1 mg/s x m MPa y 20

m 2.2

-2000

20

30

40

50

60

70

80

90

100

0°C 100 200 300 400-100

pib

ar

3

2

1

-2000

20

30

40

50

60

70

80

90

100

0°C 100 200 300 400-100

pib

ar

3

2

1

-2000

20

30

40

50

60

70

80

90

100

0°C 100 200 300 400-100

pib

ar

3

2

1

www.klinger.co.at

KLINGERSIL® C-4500KLINGERSIL® C-4500 is a premium quality high-pressure gasket especially suitable for use with high temperature alkaline media and superheated steam.It is a superior performance product designed for the use in the chemical industry.

Carbon fibres and special heat resistant additives, bonded with NBR.Suitable for use with alkaline media and steam at higher tem-peratures as well as to oils, gases, salt solutions, fuels, alco-hols, organic and inorganic acids, hydrocarbons, lubricants and refrigerants.

» Utilization of carbon fibres » Heat resistant additives » Resistant to creep and cold flow » Dimensionally stable

» BAM-tested » DIN-DVGW » DIN-DVGW W 270 » Elastomer-Guideline » ÖVGW » German Lloyd » TA-Luft (Clean air) » Fire-Safe acc. to DIN EN ISO 10497

Key features:

» Suitable for high temperature alkaline media » Suitable for superheated steam

Benefits:

Properties:

Industries:

SUPERIOR

EXCELLENT

VERY GOOD

GOOD

MODERATE

MECHANICALRESISTANCE

THERMALRESISTANCE

SEALABILITY CHEMICALRESISTANCE

Certificates and approvals:

TRANSPORTPULP & PAPEROIL & GASCHEMICAL INFRASTRUCTUREENERGYINDUSTRY FOOD & BEVERAGES

referring to KLINGERSIL® product range

PHARMA

www.klinger.co.at

pT diagram for thickness 2.0 mm:

Typical technical data for thickness 2.0 mm:

Certified acc. to DIN EN ISO 9001:2008 Subject to technical alterations. Status: March 2016

Rich. Klinger Dichtungstechnik GmbH & Co KG » Am Kanal 8-10 » A-2352 Gumpoldskirchen, AustriaTel +43 (0) 2252/62599-137 » Fax +43 (0) 2252/62599-296 » e-mail: marketing@klinger.co.at

1000 x 1500 mm, 2000 x 1500 mm

0.5 mm, 1.0 mm, 1.5 mm, 2.0 mm, 3.0 mm

Thicknesses:

Thickness acc. DIN 28091-1Length 50 mm, width 50 mm

Other thicknesses, sizes and tolerances on request.

Tolerances:

Dimensions of the standard sheets:

Sizes:

2 31

In area one, the gasket material is normally sui-table subject to chemical compatibility.

In area two, the gasket material may be suitable but a technical evaluation is recommended.

In area three, do not in-stall the gasket without a technical evaluation.

Always refer to the che-mical resistance of the gasket to the media.

Compressibility ASTM F 36 J % 11

Recovery ASTM F 36 J % 60

Stress relaxation DIN 52913 50 MPa, 16 h/175°C MPa 38

50 MPa, 16 h/300°C MPa 30

Stress relaxation BS 7531 40 MPa, 16 h/300°C MPa 30

KLINGER cold/hot compression thickness decrease at 23°C % 10

50 MPa thickness decrease at 300°C % 15

Tightness DIN 28090-2 mg/s x m 0.05

Specific leakrate λ VDI 2440 mbar x l/s x m 4.94E-06

Thickness increase after fluid oil IRM 903: 5 h/150°C % 3

immersion ASTM F 146 fuel B: 5 h/23°C % 5

Density g/cm3 1.6

Average surface resistance ρO Ω 8.0x10E04

Thermal conductivity λ W/mK 0.43

Classification acc. to BS 7531:2006 Grade AX

ASME-Code sealing factors

for gasket thickness 1.0 mm tightness class 0.1 mg/s x m MPa y 20

m 1.0

for gasket thickness 2.0 mm tightness class 0.1 mg/s x m MPa y 20

m 1.6

for gasket thickness 3.0 mm tightness class 0.1 mg/s x m MPa y 20

m 2.0

-2000

20

30

40

50

60

70

80

90

100

0°C 100 200 300 400-100

pib

ar

-2000

20

30

40

50

60

70

80

90

100

0°C 100 200 300 400-100

pib

ar

-2000

20

30

40

50

60

70

80

90

100

0°C 100 200 300 400-100

pib

ar

3

2

1

3

2

1

3

2

1

www.klinger.co.at

KLINGERSIL® C-4509KLINGERSIL® C-4509 is a special high-pressure gasket for highest thermal and mechanical stresses.Due to the expanded metal reinforcement it offers a high stress capability and is suitable for high bolt loads. The basic material KLINGERSIL® C-4500 is a Fire Safe grade.

Carbon fibres and special high temperature resistant additi-ves, bonded with NBR.Made from high-tech materials it offers excellent service in many sectors of the chemical industry. Main fields of applica-tion: alkaline media and steam.

» Utilization of carbon fibres » Expanded metal reinforcement » Improved stress relaxation

» German Lloyd

Key features:

» Suitable for high-pressure applications » Higher resistance against blow-outs » More safety at high internal pressures

Benefits:

Properties:

Industries:

SUPERIOR

EXCELLENT

VERY GOOD

GOOD

MODERATE

MECHANICALRESISTANCE

THERMALRESISTANCE

SEALABILITY CHEMICALRESISTANCE

Certificates and approvals:

TRANSPORTPULP & PAPEROIL & GASCHEMICAL ENERGYINDUSTRY

referring to KLINGERSIL® product range

INFRASTRUCTURE FOOD & BEVERAGES

PHARMA

www.klinger.co.at

pT diagram for thickness 1.5 mm:

Typical technical data for thickness 2.0 mm:

Certified acc. to DIN EN ISO 9001:2008 Subject to technical alterations. Status: March 2016

Rich. Klinger Dichtungstechnik GmbH & Co KG » Am Kanal 8-10 » A-2352 Gumpoldskirchen, AustriaTel +43 (0) 2252/62599-137 » Fax +43 (0) 2252/62599-296 » e-mail: marketing@klinger.co.at

1000 x 1500 mm, 2000 x 1500 mm

1000 x 1230 mm, 2000 x 1230 mm

Sizes KLINGERSIL® C-4509 L:

Thickness acc. DIN 28091-1Length 50 mm, width 50 mm

Other thicknesses, sizes and tolerances on request.

Tolerances:

Dimensions of the standard sheets:

Sizes KLINGERSIL® C-4509:

2 31

In area one, the gasket material is normally sui-table subject to chemical compatibility.

In area two, the gasket material may be suitable but a technical evaluation is recommended.

In area three, do not in-stall the gasket without a technical evaluation.

Always refer to the che-mical resistance of the gasket to the media.

Compressibility ASTM F 36 J % 12

Recovery ASTM F 36 J % 65

Stress relaxation DIN 52913 50 MPa, 16 h/300°C MPa 39

Stress relaxation BS 7531 40 MPa, 16 h/300°C MPa 38

KLINGER cold/hot compression thickness decrease at 23°C % 9

50 MPa thickness decrease at 300°C % 7

Thickness increase after fluid oil IRM 903: 5 h/150°C % 3

immersion ASTM F 146 fuel B: 5 h/23°C % 5

Density g/cm3 2.0

ASME-Code sealing factors

for gasket thickness 1.0 mm tightness class 0.1 mg/s x m MPa y 30

m 3.1

for gasket thickness 2.0 mm tightness class 0.1 mg/s x m MPa y 30

m 4.4

for gasket thickness 3.0 mm tightness class 0.1 mg/s x m MPa y 30

m 6.0

1.0 mm, 1.5 mm

Thicknesses:

-2000

20

30

40

50

60

70

80

90

100

0°C 100 200 300 400-100

pib

ar

3

2

1

-2000

20

30

40

50

60

70

80

90

100

0°C 100 200 300 400-100

pib

ar

3

2

1

www.klinger.co.at

KLINGERSIL® C-6327Swelling in oil and fuels KLINGERSIL® C-6327offers an excellent conformity with flanges at low surface loads.

Aramid fibres and inorganic fibres bonded with SBR.Fields of application: Body gaskets for liquids and steam at lower pressures and temperatures and low bolt loads, e.g. transformer gaskets.

» Use of SBR rubber as binder » High compressibility

» German Lloyd

Key features:

» Controlled swelling in oils and fuels » Provides very good adaptability to any sealing surface » Conforms easily » Excellent sealing at low stress » Improved radiation resistance

Benefits:

Properties:

Industries:

SUPERIOR

EXCELLENT

VERY GOOD

GOOD

MODERATE

MECHANICALRESISTANCE

THERMALRESISTANCE

SEALABILITY CHEMICALRESISTANCE

Certificates and approvals:

OIL & GAS TRANSPORTINFRASTRUCTUREENERGYINDUSTRY

referring to KLINGERSIL® product range

CHEMICAL FOOD & BEVERAGES

PHARMAPULP & PAPER

www.klinger.co.at

Compressibility ASTM F 36 J % 25

Recovery ASTM F 36 J % 45

Stress relaxation DIN 52913 50 MPa, 16 h/175°C MPa 25

KLINGER cold/hot compression thickness decrease at 23°C % 20

50 MPa thickness decrease at 300°C % 32

Tightness DIN 28090-2 mg/s x m 0.02

Thickness increase after fluid oil IRM 903: 5 h/150°C % 45

immersion ASTM F 146 fuel B: 5 h/23°C % 30

Density g/cm3 1.7

Average surface resistance ρO Ω 4.5x10E14

Average specific volume resistance ρD Ω cm 6.8x10E13

Average dielectric strength Ed kV/mm 13

Average power factor 50 Hz tan δ 0.049

Average dielectric coefficient 50 Hz εr 5.8

pT diagram for thickness 2.0 mm:

Typical technical data for thickness 2.0 mm:

Certified acc. to DIN EN ISO 9001:2008 Subject to technical alterations. Status: March 2016

Rich. Klinger Dichtungstechnik GmbH & Co KG » Am Kanal 8-10 » A-2352 Gumpoldskirchen, AustriaTel +43 (0) 2252/62599-137 » Fax +43 (0) 2252/62599-296 » e-mail: marketing@klinger.co.at

1000 x 1500 mm, 2000 x 1500 mm

0.5 mm, 1.0 mm, 1.5 mm

Thicknesses:

Thickness acc. DIN 28091-1Length 50 mm, width 50 mm

Other thicknesses, sizes and tolerances on request.

Tolerances:

Dimensions of the standard sheets:

Sizes:

2 31

In area one, the gasket material is normally sui-table subject to chemical compatibility.

In area two, the gasket material may be suitable but a technical evaluation is recommended.

In area three, do not in-stall the gasket without a technical evaluation.

Always refer to the che-mical resistance of the gasket to the media.

KLINGERSIL® C-6327 / 1mm KLINGERSIL® C-6327 / 2mm KLINGERSIL® C-6327 / 3mm

-2000

20

30

40

50

60

70

80

90

100

0°C 100 200 300 400-100

pib

ar

-2000

20

30

40

50

60

70

80

90

100

0°C 100 200 300 400-100

pib

ar

-2000

20

30

40

50

60

70

80

90

100

0°C 100 200 300 400-100

pib

ar

3

2 1

3

2 1

3

2 1

www.klinger.co.at

KLINGERSIL® C-8200KLINGERSIL® C-8200 is a premium high- pressure gasket which offers more safety for the use with high concentra-ted acids.

Glass fibres bonded with special acid resistant elastomers.This material is resistant to a wide variety of media and espe-cially to acids.

» Special acid-resistant elastomer as binder » Flame retardant binder

» German Lloyd » TA-Luft (Clean air)

Key features:

» Resistant to a variety of media especially acids » Improved ozone resistance

Benefits:

Properties:

Industries:

SUPERIOR

EXCELLENT

VERY GOOD

GOOD

MODERATE

MECHANICALRESISTANCE

THERMALRESISTANCE

SEALABILITY CHEMICALRESISTANCE

Certificates and approvals:

PULP & PAPEROIL & GASCHEMICAL ENERGYINDUSTRY

referring to KLINGERSIL® product range

INFRASTRUCTURE TRANSPORT FOOD & BEVERAGES

PHARMA

www.klinger.co.at

pT diagram for thickness 2.0 mm:

Typical technical data for thickness 2.0 mm:

Certified acc. to DIN EN ISO 9001:2008 Subject to technical alterations. Status: March 2016

Rich. Klinger Dichtungstechnik GmbH & Co KG » Am Kanal 8-10 » A-2352 Gumpoldskirchen, AustriaTel +43 (0) 2252/62599-137 » Fax +43 (0) 2252/62599-296 » e-mail: marketing@klinger.co.at

1000 x 1500 mm, 2000 x 1500 mm

0.5 mm, 1.0 mm, 1.5 mm, 2.0 mm, 3.0 mm

Thicknesses:

Thickness acc. DIN 28091-1Length 50 mm, width 50 mm

Other thicknesses, sizes and tolerances on request.

Tolerances:

Dimensions of the standard sheets:

Sizes:

2 31

In area one, the gasket material is normally sui-table subject to chemical compatibility.

In area two, the gasket material may be suitable but a technical evaluation is recommended.

In area three, do not in-stall the gasket without a technical evaluation.

Always refer to the che-mical resistance of the gasket to the media.

Compressibility ASTM F 36 J % 9

Recovery ASTM F 36 J % 55

KLINGER cold/hot compression thickness decrease at 23°C % 7

25 MPa thickness decrease at 200°C % 15

Specific leakrate λ VDI 2440 mbar x l/s x m 9.17E-09

Density g/cm3 1.7

Acid tests

Thickness increase after fluid HNO3, 96%, 18 h/23°C % unsuitable

immersion ASTM F 146 H2SO4, 96%, 18 h/23°C % 15

H2SO4, 65%, 48 h/23°C % 8

oil IRM 903: 5 h/150°C % 5

fuel B: 5 h/23°C % 10

Average surface resistance ρO Ω 5.8x10E11

Average specific volume resistance ρD Ω cm 4.1x10E12

Average dielectric strength Ed kV/mm 17.0

Average power factor 50 Hz tan δ 0.228

Average dielectric coefficient 50 Hz εr 9.4

ASME-Code sealing factors

for gasket thickness 1.0 mm tightness class 0.1 mg/s x m MPa y 20

m 2.1

for gasket thickness 2.0 mm tightness class 0.1 mg/s x m MPa y 20

m 3.0

for gasket thickness 3.0 mm tightness class 0.1 mg/s x m MPa y 20

m 6.2

KLINGERSIL® C-8200 / 1mm KLINGERSIL® C-8200 / 2mm KLINGERSIL® C-8200 / 3mm

-2000

20

30

40

50

60

70

80

90

100

0°C 100 200 300 400-100

pib

ar

-2000

20

30

40

50

60

70

80

90

100

0°C 100 200 300 400-100

pib

ar

-2000

20

30

40

50

60

70

80

90

100

0°C 100 200 300 400-100

pib

ar

3

2

1

3

2

1

3

2

1