- 1 -

KNÜRR MOBILE CABINET Knürr Mobile Equipment Carriers

- 2 -

Content

Please read

1.1 General Information 3

1.2 Markings and Symbols 4

1.3 Safe Operation 4

1.4 Warranty 5

1.5 Service 5

1.6 Standards and Regulations 5

2.1 Delivery 5

2.2 Assembly 6

2.3 Assembly Instructions 6

3.1 Fitting the slide rails to the drawer shelf 7

3.2 Fitting side panels and bottom cover to the wheel base 8

3.3 Fitting the fixed shelf to side panels 9

3.4 Fitting the top cover 9

3.5 Fitting the slide rails to side panels 10

3.6 Fitting the rear panel 10

3.7 Fitting the cable winder 11

3.8 Inserting the drawer 11

3.9 Fitting the front door 12

3.10 Fitting the VCM and VMM holders 12

3.11 Fitting the cable pole 13

4.1 Fitting the docking station CF-VEB531 to the top cover 14

4.2 Fitting the docking station CF-WEB194 to the top cover 15

4.3 Fitting the docking station CF-VEBD11 to the top cover 16

4.4 Safety 17

5.1 Drawings 18

- 3 -

Please read

The Knürr Mobile Cabinet Thank you for choosing Snap-on’s Knürr Mobile Cabinet. This trolley is prepared for self-installation. Required tools are not part of the delivery.

Validity of this manual

This manual applies to the Knürr Mobile Cabinet:

Snap-on item number KNUMABCAB

Proper usage

The components of the Snap-on Trolley are designed for workshop, garage and industrial use in a dry professional environment. The use in other areas, for example in a wet room, outdoors or for applications other than mentioned, shall be deemed improper.

The manufacturer will refuse all warranty and liability claims caused by improper usage, or if components are added or modified without authorization.

1.1 General Information

Copyright

All rights to this manual are owned by Knürr. Reproduction and reprinting of this manual, in whole or in part are permitted only if the source of the information is specified.

Technical status

Technical status of the manual is 09/2013. Knürr reserves the right to

- modify the design or the components of the trolley, or

- use equivalent components other than those shown where this serves technical progress

- modify the information contained in this manual without prior notice.

Liability

Knürr can not accept responsibility for the completeness and correctness of the information. In particular, we accept no liability for damages which result from incorrect use or operation of the product.

- 4 -

1.2 Markings and symbols Important passages are emphasized in the text and it is essential to take note of them

as follows:

1.3 Safe operation The Knürr Mobile Cabinet is delivered in perfectly safe working conditions.

Knürr Technical Furniture GmbH can only guarantee the safety, reliability and function of the Knürr Mobile Cabinet if it is assembled, used, extended and modified as described in this manual.

• Keep this manual for future use.

• Check for external damages before putting into operation! If damage or some kind of defect is determined, the Snap-on Trolley may not be operated.

• In case of damage and defects please contact your distributor.

• Do not use the Knürr Mobile Cabinet in damp rooms.

• Assembly, installation and start-up operation only by trained personnel. Only carry out the work described in this manual.

• If a fault occurs (while setting up the system) please contact the customer service (see 1.5).

• Refer also to the documentation (from other manufacturers) supplied for connected devices and accessories.

Danger Requires safety measures to be taken to protect the health of personnel concerned.

Warning Emphasizes what has to be done or refrained from being done in order to avoid damaging valuable property.

Information Recommends ways of dealing with certain elements and gives instructions for smooth and quick assembly.

- 5 -

1.4 Warranty Knürr provides a warranty for 12 months, starting on the date of delivery, on all mechanical and electrical components. Further details can be found in the enclosed General Business Conditions of Knürr.

1.5 Service Knürr Technical Support will be glad to assist you with any queries. Please contact:

Knürr GmbH

Mariakirchener Straße 38

D-94424 Arnstorf

Phone: +49 (0) 87 23/28-0

Fax: +49 (0) 87 23/28-138

e-mail: furniture@knuerr.com

1.6 Standards and Regulations Snap-on’s Knürr Mobile Cabinet, made by Knürr Technical Furniture GmbH has been designed and tested in accordance with the relevant standards and regulations.

- DIN 4554:1986 Office furniture – requirement and testing

- DIN EN 527-2:2003 Office furniture - Work tables and desks

- DIN EN 12527 Castors and wheels - Test methods and apparatus

- DIN 31000/A1:2007 General guide for designing of technical equipments to satisfy safety requirements

2.1 Delivery

Shipping damage

Items supplied

The elements of the Knürr Mobile Cabinet are partly assembled by the manufacturer before delivery. Read before transporting to the installation site.

• Note the accident prevention regulations when working with a lift truck or fork lift truck.

Danger If the components have clearly suffered shipping damage, we cannot guarantee that they are safe. • Report shipping damage to the forwarder or manufacturer immediately after delivery.

- 6 -

2.2 Assembly Remove the packaging

Waste disposal

All the materials used in the packaging can be recycled. • Dispose of all waste in an environmentally friendly manner using local facilities. • Comply with current regulations relating to environmental protection and waste disposal.

Lifting heavy loads

2.3 Assembly instructions

Tools required (not supplied)

–– Spanner 7mm, 8mm, 10mm

––Torx wrench T25 security version

–– Allen key 5mm

–– Philipshead screwdriver

Mounting material (supplied)

–– Allen screw M6x12 (6x)

–– Allen screw M6x10 (8x)

–– Phillips head screw M4x8 (10x)

–– Phillips head screw M4x5 (4x)

–– Phillips head screw M6x10 (2x)

–– Tensilock Nut M6 (4x)

–– Tensilock Nut M5 (6x)

–– Nut M4 (12x)

–– M5x10 Torx T25 security screw (8x)

–– Countersunk screw M4x6 (2x)

Warning Danger of damaging the paintwork. • Cut the cardboard carefully.

Danger Danger of accidents and damage to health when you carry heavy, awkward items. • At least two persons should always lift and carry heavy, awkward items. • Always use your knees to lift heavy items, not your back.

- 7 -

3.1 Fitting the slide rails to the drawer shelf

Pull apart slide rails

Prepare drawer shelf, inner side of rails and 4x screws Phillips head M4x5

Mount inner part of slide rails to the sides of the drawer shelf

- 8 -

3.2 Fitting side panels and bottom cover to the wheel base

Prepare 6x Allen screw M6x12

Prepare wheel base with pre-assembled casters, bottom cover and left and right side panel.

Place them sideways for easy installation or have a helper secure the side panels.

Mount bottom cover together with side panels to the wheel base.

Be aware of the orientation: Castors with brake to be at the front.

Bottom cover

Side panel

- 9 -

3.3 Fitting the fixed shelf to the side panels

Prepare fixed shelf and 4x Tensilock Nut M6

Hang shelf into the threaded press-studs in the middle of the cabinet sides and bolt down with the Tensilock nuts.

3.4 Fitting the top cover

Prepare top cover and 6x Nut M4

Align top cover’s threaded press-studs with both side panels and bolt down with nuts M4.

- 10 -

3.5 Fitting the slide rails to the side panels

Prepare outer parts of slide rails and 4x Phillips head screw M4x8

Mount outer parts of the slide rails to mounting bracket on each side panel.

3.6 Fitting the rear panel Prepare rear panel and 6x Screw M5x10 Torx T25 secure

Secure the rear panel to 3 positions on each side panel.

- 11 -

3.7 Fitting the cable winder Connect the cable winder with its extension,

then mount them to the treaded press-studs of the rear panel.

3.8 Insert the drawer shelf Align the slide rails and insert the drawer shelf carefully.

- 12 -

3.9 Fitting the front door

Prepare door, 6x Nut M4 and 6x Phillips head screw M4x8

Hinges are pre-mounted to the door. Align the door with hinges to the mounting positions of the right side panel. Secure with Phillips-head screws and nuts (nuts inside side panel).

3.10 Fitting the VCM and VMM holders Prepare 6x Allen screw M6x10 Prepare 2x Phillips head screw M6x10

- 13 -

3.11 Fitting the cable pole Prepare cable pole, holder with thumb screw and 2x Allen screw M6x10

Mount cable pole holder to left side of cabinet with 2x Allen screw M6x10

Insert cable pole into holder and secure with thumb screw.

- 14 -

4.1 Fitting the docking station CF-VEB531 to the top cover Prepare bracket, Counter Sunk Screw M4 (2x) and Tensilock Nut M5 (2x)

First, mount retaining bracket to underside of docking station CF-VEB531 with 2x Counter Sunk Screws M4.

Then, remove plastic plugs from top cover and secure the docking station unit to top cover of cabinet with 2x Tensilock Nut M5 from inside the cabinet.

- 15 -

4.2 Fitting the docking station CF-WEB194 to the top cover Prepare bracket, Tensilock Nut M5 (2x) and Screw DIN7985 M5x10 Torx T25 secure (2x)

First, connect the docking station unit with the bracket left and right, using Secure Torx Wrench T25. Bracket inside of docking station sides.

Then, remove plastic plugs from top cover and secure the docking station unit to top cover of cabinet with 2x Tensilock Nut M5 from inside the cabinet. You can choose two mounting positions as desired.

Position 1

Position 2

- 16 -

4.3 Fitting the docking station CF-VEBD11 to the top cover Prepare 2x brackets (left and right) and Tensilock Nut M5 (4x)

Hook the brackets into the docking station as shown.

Remove the plastic plugs from the top cover and position the docking station and both brackets with the threaded press-studs on the top cover through the four mounting holes.

Secure the docking station unit to thetop cover of the cabinet with 4x Tensilock Nut M5 from inside the cabinet.

- 17 -

4.4 Safety Locking the door:

Door remains closed through the retaining magnets in the left side panel.

Overnight safety: Store all equipment inside the cabinet and lock the front door with a padlock (not supplied) through the hasps as indicated.

Use the front wheel brakes to

ensure a secure stand of the cabinet

Locking the complete cabinet:

.

Lock the complete cabinet, e.g. with a chain and padlock, or a bicycle lock through the hole, provided in the wheel base of the cabinet.

- 18 -

5.1 Drawings

- 19 -