l5 thyristor protection
TRANSCRIPT
![Page 1: L5 thyristor protection](https://reader038.vdocuments.net/reader038/viewer/2022110200/55c5c767bb61eb866a8b460a/html5/thumbnails/1.jpg)
EE-321 N
Lecture-5
Thyristor Protection Through Snubber Circuits
![Page 2: L5 thyristor protection](https://reader038.vdocuments.net/reader038/viewer/2022110200/55c5c767bb61eb866a8b460a/html5/thumbnails/2.jpg)
Introduction
• A thyristor needs protection against overvoltages, overcurrents, high dv/dt and high di/dt
• O/V and O/C protection can generally be achieved by zener diodes and fuses etc.
• However, device is protected against high dv/dt and high di/dt using snubber circuits
8-Sep-12 2 EE-321N, Lec-6
![Page 3: L5 thyristor protection](https://reader038.vdocuments.net/reader038/viewer/2022110200/55c5c767bb61eb866a8b460a/html5/thumbnails/3.jpg)
Types of Snubbers
1. Turn-ON snubbers to reduce sudden rise of current (di/dt)
2. Turn-OFF snubbers to reduce sudden rise of voltage (dv/dt)
3. Snubbers for reducing v & i stresses on the device during switching (for power transistors)
4. Energy recovery snubbers
8-Sep-12 3 EE-321N, Lec-6
![Page 4: L5 thyristor protection](https://reader038.vdocuments.net/reader038/viewer/2022110200/55c5c767bb61eb866a8b460a/html5/thumbnails/4.jpg)
di/dt snubber
8-Sep-12 EE-321N, Lec-6 4
![Page 5: L5 thyristor protection](https://reader038.vdocuments.net/reader038/viewer/2022110200/55c5c767bb61eb866a8b460a/html5/thumbnails/5.jpg)
di/dt snubber
• Under steady state operation, Dm will conduct when thyristor T1 is OFF
• If T1 is triggered when Dm is still conducting, di/dt can be very high
• In practice, the di/dt is limited by adding a series inductor Ls (also includes stray inductance)
8-Sep-12 EE-321N, Lec-6 5
s
sss
L
V
dt
di
dt
diLV
![Page 6: L5 thyristor protection](https://reader038.vdocuments.net/reader038/viewer/2022110200/55c5c767bb61eb866a8b460a/html5/thumbnails/6.jpg)
dv/dt Snubber
8-Sep-12 6 EE-321N, Lec-6
![Page 7: L5 thyristor protection](https://reader038.vdocuments.net/reader038/viewer/2022110200/55c5c767bb61eb866a8b460a/html5/thumbnails/7.jpg)
dv/dt Snubber
• Series combination of R & C shunted across the device
• C takes care of dv/dt while R limits the discharge current when thyristor is switched ON
• A more effective variation is the polarized snubber in which there is additional diode in parallel with R
• The diode bypasses the resistor to reduce the response time of RC for +ve spikes (which may turn ON the device)
8-Sep-12 EE-321N, Lec-6 7
![Page 8: L5 thyristor protection](https://reader038.vdocuments.net/reader038/viewer/2022110200/55c5c767bb61eb866a8b460a/html5/thumbnails/8.jpg)
Polarized Snubber
8-Sep-12 EE-321N, Lec-6 8
![Page 9: L5 thyristor protection](https://reader038.vdocuments.net/reader038/viewer/2022110200/55c5c767bb61eb866a8b460a/html5/thumbnails/9.jpg)
Analysis
• If switch S1 is closed at t = 0, a step voltage will be applied across the thyristor T1
• The dv/dt may be high enough to turn on the device
• The dv/dt can be limited by connecting a capacitor Cs across T1
• When the thyristor T1 is turned on, the discharge current of capacitor is limited by resistor Rs
8-Sep-12 EE-321N, Lec-6 9
![Page 10: L5 thyristor protection](https://reader038.vdocuments.net/reader038/viewer/2022110200/55c5c767bb61eb866a8b460a/html5/thumbnails/10.jpg)
Analysis
• The circuit dv/dt can be found approximately from:
• The snubber circuit can be designed based on the known value of the dv/dt for a device
• The value of Rs is found from the discharge current ITD
8-Sep-12 EE-321N, Lec-6 10
ss
ss
CR
VV
dt
dv 632.0632.0
TD
ss
I
VR
![Page 11: L5 thyristor protection](https://reader038.vdocuments.net/reader038/viewer/2022110200/55c5c767bb61eb866a8b460a/html5/thumbnails/11.jpg)
Design Example (Ex. 7.4 MHR)
For the circuit configuration shown, input voltage is Vs = 200 V with load resistance R = 5 Ω. The load and stray inductances are negligible and the thyristor is operated at a frequency of fs = 2 kHz. If the required dv/dt is 100 V/µs and the discharge current is to be limited to 100 A. Determine: (a) the values of Rs, Cs,
(b) snubber loss, and
(c) the power rating of snubber resistor.
8-Sep-12 EE-321N, Lec-6 11
![Page 12: L5 thyristor protection](https://reader038.vdocuments.net/reader038/viewer/2022110200/55c5c767bb61eb866a8b460a/html5/thumbnails/12.jpg)
Solution on Board
8-Sep-12 EE-321N, Lec-6 12
![Page 13: L5 thyristor protection](https://reader038.vdocuments.net/reader038/viewer/2022110200/55c5c767bb61eb866a8b460a/html5/thumbnails/13.jpg)
Try Yourself
For an RL load with R = 2.5 Ω, find the min. value of L so that the thyristor switch is not damaged due to high di/dt. The di/dt limit for the thyristor is 50 A/µs.
8-Sep-12 EE-321N, Lec-6 13
+ −
i 500 V