lab report
TRANSCRIPT
UNIVERSITI TEKNOLOGI MARA
FACULTY OF ELECTRICAL ENGINEERING
INTERNET PROTOCOLECE734
PREPARED BY:
MAHATHIR BIN JOHAR
ID NUMBER:
2009241034
PREPARED FOR
DR MAT IKRAM YUSOF
Chapter 3 Lab 3-7, OSPF Case Study Topology
Objectives • Plan, design, and implement the International Travel Agency network shown in the diagram and described below. • Verify that all configurations are operational and functioning according to the guidelines.
Note: This lab uses Cisco 1841 routers with Cisco IOS Release 12.4(24)T1 and the Advanced IP Services image c1841-advipservicesk9-mz.124-24.T1.bin. You can use other routers (such as a 2801 or 2811) and Cisco IOS Software versions if they have comparable capabilities and features. Depending on the router model and Cisco IOS Software version, the commands available and output produced might vary from what is shown in this lab.
Required Resources • 4 routers (Cisco 1841 with Cisco IOS Release 12.4(24)T1 Advanced IP Service or comparable) • Serial and console cables
Requirements The International Travel Agency needs its core network set up for OSPF with the specifications indicated in the diagram and listed below. Design, configure, and test a network that meets all the following requirements:
1. Use the addressing scheme shown in the diagram. 2. Configure OSPF with the networks shown in the diagram. 3. Configure the OSPF backbone area to be on Loopback0 on HQ. 4. Configure the Frame Relay subnets as point-to-point subinterfaces, with the link between HQ and East in area 100, and the link between HQ and West in area 300. 5. Configure area 300 as an NSSA. 6. Configure the router East loopback interfaces to be in area 200. Summarize this area with the most efficient summary. 7. Redistribute the loopback network on router West into OSPF. 8. Create virtual links as necessary for full connectivity.
9. Make sure that all loopback interfaces are advertised with the correct subnet mask. # Lab 3-7 OSPF Case Study# By :Dr Mat IkramYusof CCNP,CCSP,CCNA,CCAI,SCNA,SCSA,SCJP,ITILF################################################################## To get available chassis and NM, run "dynamips -H 7200 &dynamips -H 7201 &" from# the command line in the dynamipsdirectory.And " dynagen Lab1-0"## Available C3600 chassis drivers:# * 3620# * 3640# * 3660################################################################## Available C3600 Network Module drivers:# * NM-1E# * NM-4E# * NM-1FE-TX# * NM-4T# * Leopard-2FE# * NM-16ESW#################################################################
mmap = trueghostios = Truesparsemem = Trueautostart = False
[localhost:7200]
#workingdir = C:\Program Files\Dynamips\sample_labs\internetworkexpert\workingworkingdir = C:\Program Files (x86)\Dynamips\sample_labs\ccnp1Labs\OSPF\Lab3-8\working
[[3640]] # # Specify 3640 IOS image on Windows here: #image = C:\Program Files\Dynamips\images\c3640-jk9o3s-mz.123-14.T7.extracted.bin # # Specify 3640 IOS image on Linux here: # image = /ios/c3640-jk9o3s-mz.123-14.T7.extracted.binimage = C:\Program Files (x86)\Dynamips\images\c3640-jk9o3s-mz.124-5a.bin #ram = 128 disk0 = 0 disk1 = 0 # Choose an idlepc value from the belowidlepc = 0x60610428
########################### # # Define router instances # ###########################
[[ROUTER FRS]]model = 3640console = 2009 slot1 = NM-4Ts1/0 = HQ s1/0s1/1 = East s1/0s1/2 = West s1/0
[[ROUTER West]]model = 3640console = 2012 slot1 = NM-4Ts1/0 = FRS s1/2
[[ROUTER HQ]]model = 3640console = 2011 slot1 = NM-4Ts1/0 = FRS s1/0
[[ROUTER East]]model = 3640console = 2010 slot1 = NM-4Ts1/0 = FRS s1/1
ROUTER 3(FRS) CONFIGURATION
FRS#sh run
Building configuration...
Current configuration : 1226 bytes
version 12.4
service timestamps debug datetimemsec
service timestamps log datetimemsec
no service password-encryption
hostname FRS
boot-start-marker
boot-end-marker
noaaa new-model
resource policy
memory-sizeiomem 5
ipcef
frame-relay switching
interface Serial1/0
noip address
encapsulation frame-relay
serial restart-delay 0
clock rate 64000
nodce-terminal-timing-enable
frame-relayintf-type dce
frame-relay route 102 interface Serial1/1 201
frame-relay route 103 interface Serial1/2 301
!
interface Serial1/1
noip address
encapsulation frame-relay
serial restart-delay 0
clock rate 64000
nodce-terminal-timing-enable
frame-relayintf-type dce
frame-relay route 201 interface Serial1/0 102
!
interface Serial1/2
noip address
encapsulation frame-relay
serial restart-delay 0
clock rate 64000
nodce-terminal-timing-enable
frame-relayintf-type dce
frame-relay route 301 interface Serial1/0 103
!
interface Serial1/3
noip address
shutdown
serial restart-delay 0
nodce-terminal-timing-enable
!
ip http server
noip http secure-server
control-plane
line con 0
line aux 0
linevty 0 4
!
End
ROUTER 1(HQ) CONFIGURATION
HQ#sh run
Building configuration...
Current configuration : 1354 bytes
version 12.4
service timestamps debug datetimemsec
service timestamps log datetimemsec
no service password-encryption
hostname HQ
boot-start-marker
boot-end-marker
no aaa new-model
resource policy
memory-sizeiomem 5
ipcef
!
interface Loopback1
ip address 10.1.1.9 255.255.255.252
ipospf network point-to-point
!
interface Serial1/0
noip address
encapsulation frame-relay
serial restart-delay 0
nodce-terminal-timing-enable
!
interface Serial1/0.102 point-to-point
ip address 10.1.1.1 255.255.255.252
frame-relay interface-dlci 102
!
interface Serial1/0.103 point-to-point
ip address 10.1.1.5 255.255.255.252
frame-relay interface-dlci 103
!
interface Serial1/1
noip address
shutdown
serial restart-delay 0
nodce-terminal-timing-enable
!
interface Serial1/2
noip address
shutdown
serial restart-delay 0
nodce-terminal-timing-enable
!
interface Serial1/3
noip address
shutdown
serial restart-delay 0
nodce-terminal-timing-enable
!
routerospf 1
log-adjacency-changes
area 100 virtual-link 10.1.1.113
area 300 nssa
network 10.1.1.0 0.0.0.3 area 100
network 10.1.1.4 0.0.0.3 area 300
network 10.1.1.8 0.0.0.3 area 0
!
ip http server
noip http secure-server
control-plane
line con 0
line aux 0
linevty 0 4
!
end
ROUTER 2(EAST) CONFIGURATION
EAST#sh run
Building configuration...
Current configuration : 1637 bytes
version 12.4
service timestamps debug datetimemsec
service timestamps log datetimemsec
no service password-encryption
hostname EAST
boot-start-marker
boot-end-marker
noaaa new-model
resource policy
memory-sizeiomem 5
ipcef
interface Loopback101
ip address 10.1.1.101 255.255.255.252
ipospf network point-to-point
!
interface Loopback105
ip address 10.1.1.105 255.255.255.252
ipospf network point-to-point
!
interface Loopback109
ip address 10.1.1.109 255.255.255.252
ipospf network point-to-point
!
interface Loopback113
ip address 10.1.1.113 255.255.255.252
ipospf network point-to-point
!
interface Serial1/0
noip address
encapsulation frame-relay
serial restart-delay 0
nodce-terminal-timing-enable
!
interface Serial1/0.201 point-to-point
ip address 10.1.1.2 255.255.255.252
frame-relay interface-dlci 201
!
interface Serial1/1
no ip address
shutdown
serial restart-delay 0
no dce-terminal-timing-enable
!
interface Serial1/2
no ip address
shutdown
serial restart-delay 0
no dce-terminal-timing-enable
!
interface Serial1/3
no ip address
shutdown
serial restart-delay 0
no dce-terminal-timing-enable
!
Router ospf 1
log-adjacency-changes
area 100 virtual-link 10.1.1.9
area 200 range 10.1.1.96 255.255.255.224
network 10.1.1.0 0.0.0.3 area 100
network 10.1.1.100 0.0.0.3 area 200
network 10.1.1.104 0.0.0.3 area 200
network 10.1.1.108 0.0.0.3 area 200
network 10.1.1.112 0.0.0.3 area 200
!
ip http server
no ip http secure-server
control-plane
!
line con 0
line aux 0
line vty 0 4
!
!
End
ROUTER 4(WEST) CONFIGURATION
WEST#sh run
Building configuration...
Current configuration : 1174 bytes
version 12.4
service timestamps debug date time msec
service timestamps log date time msec
no service password-encryption
hostname WEST
boot-start-marker
boot-end-marker
no aaa new-model
resource policy
memory-size iomem 5
ip cef
interface Loopback3
ip address 10.1.1.13 255.255.255.252
ip ospf network point-to-point
!
interface Serial1/0
no ip address
encapsulation frame-relay
serial restart-delay 0
no dce-terminal-timing-enable
!
interface Serial1/0.301 point-to-point
ip address 10.1.1.6 255.255.255.252
frame-relay interface-dlci 301
!
interface Serial1/1
no ip address
shutdown
serial restart-delay 0
no dce-terminal-timing-enable
!
interface Serial1/2
no ip address
shutdown
serial restart-delay 0
no dce-terminal-timing-enable
!
interface Serial1/3
no ip address
shutdown
serial restart-delay 0
no dce-terminal-timing-enable
!
Router ospf 1
log-adjacency-changes
area 300 nssa
redistribute connected subnets
network 10.1.1.4 0.0.0.3 area 300
ip http server
no ip http secure-server
control-plane
line con 0
line aux 0
line vty 0 4
end
RESULT
WEST(tcl)#foreach address {
+>10.1.1.9
+>10.1.1.1
+>10.1.1.5
+>10.1.1.2
+>10.1.1.101
+>10.1.1.105
+>10.1.1.109
+>10.1.1.113
+>} {
+>ping $address }
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.1.1.9, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 56/110/224 ms
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.1.1.1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 80/96/120 ms
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.1.1.5, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 52/73/124 ms
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.1.1.2, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 140/161/188 ms
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.1.1.101, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 120/154/216 ms
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.1.1.105, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 120/160/200 ms
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.1.1.109, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 120/135/168 ms
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.1.1.113, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 120/157/184 ms
WEST#sh ip ospf neighbor
Neighbor ID Pri State Dead Time Address Interface
10.1.1.9 0 FULL/ - 00:00:35 10.1.1.5 Serial1/0.301
EAST#sh ip ospf neighbor
Neighbor ID Pri State Dead Time Address Interface
10.1.1.9 0 FULL/ - - 10.1.1.1 OSPF_VL0
10.1.1.9 0 FULL/ - 00:00:34 10.1.1.1 Serial1/0.201
HQ#sh ip ospf neighbor
Neighbor ID Pri State Dead Time Address Interface
10.1.1.113 0 FULL/ - - 10.1.1.2 OSPF_VL0
10.1.1.113 0 FULL/ - 00:00:37 10.1.1.2 Serial1/0.102
10.1.1.13 0 FULL/ - 00:00:32 10.1.1.6 Serial1/0.103
HQ#sh ip route
Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
E1 - OSPF external type 1, E2 - OSPF external type 2
i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2
ia - IS-IS inter area, * - candidate default, U - per-user static route
o - ODR, P - periodic downloaded static route
Gateway of last resort is not set
10.0.0.0/8 is variably subnetted, 5 subnets, 2 masks
C 10.1.1.8/30 is directly connected, Loopback1
O N2 10.1.1.12/30 [110/20] via 10.1.1.6, 00:47:56, Serial1/0.103
C 10.1.1.0/30 is directly connected, Serial1/0.102
C 10.1.1.4/30 is directly connected, Serial1/0.103
O IA 10.1.1.96/27 [110/65] via 10.1.1.2, 00:47:56, Serial1/0.102
EAST#sh ip route
Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
E1 - OSPF external type 1, E2 - OSPF external type 2
i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2
ia - IS-IS inter area, * - candidate default, U - per-user static route
o - ODR, P - periodic downloaded static route
Gateway of last resort is not set
10.0.0.0/8 is variably subnetted, 9 subnets, 2 masks
O 10.1.1.8/30 [110/65] via 10.1.1.1, 00:48:37, Serial1/0.201
O E2 10.1.1.12/30 [110/20] via 10.1.1.1, 00:48:35, Serial1/0.201
C 10.1.1.0/30 is directly connected, Serial1/0.201
O IA 10.1.1.4/30 [110/128] via 10.1.1.1, 00:48:37, Serial1/0.201
C 10.1.1.104/30 is directly connected, Loopback105
C 10.1.1.108/30 is directly connected, Loopback109
O 10.1.1.96/27 is a summary, 00:48:57, Null0
C 10.1.1.100/30 is directly connected, Loopback101
C 10.1.1.112/30 is directly connected, Loopback113
WEST#sh ip route
Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
E1 - OSPF external type 1, E2 - OSPF external type 2
i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2
ia - IS-IS inter area, * - candidate default, U - per-user static route
o - ODR, P - periodic downloaded static route
Gateway of last resort is not set
10.0.0.0/8 is variably subnetted, 5 subnets, 2 masks
O IA 10.1.1.8/30 [110/65] via 10.1.1.5, 00:49:10, Serial1/0.301
C 10.1.1.12/30 is directly connected, Loopback3
O IA 10.1.1.0/30 [110/128] via 10.1.1.5, 00:49:10, Serial1/0.301
C 10.1.1.4/30 is directly connected, Serial1/0.301
O IA 10.1.1.96/27 [110/129] via 10.1.1.5, 00:49:10, Serial1/0.301
LAB 8-4 : IPV6 CHALLENGE LAB
3
Objectives • Implement the topology diagram using the instructions in the Requirements section. • Change the IPv6 IGP from OSPFv3 to RIPng.
Background In the first part of this lab (Steps 1 through 7), you configure IPv4 with EIGRP on routers R1, R2 and R3. You also configure IPv6 with OSPFv3 on routers R1, R3 and R4, create an IPv6 tunnel between R1 and R3 and then test network connectivity. In the second part of the lab (Step 8), you replace the OSPFv3 routing protocol with RIPng and re-test connectivity.
Required Resources Note: This lab uses Cisco 1841 routers with Cisco IOS Release 12.4(24)T1 and the Advanced IP Services image c1841-advipservicesk9-mz.124-24.T1.bin. You can use other routers (such as a 2801 or 2811) and Cisco IOS Software versions if they have comparable capabilities and features. Depending on the router model and Cisco IOS Software version, the commands available and output produced might vary from what is shown in this lab. • 4 routers (Cisco 1841 with Cisco IOS Release 12.4(24)T1 Advanced IP Services or comparable) • Serial and console cables
Requirements 1. Configure all interfaces in the topology diagram with the IPv4 or IPv6 addresses shown.
2. Use EUI-64 addresses on the link between R3 and R4.
3. Configure EIGRP AS 1 on R1, R2, and R3 to route all IPv4 networks.
4. Disable EIGRP automatic summarization.
5. Configure a manual IPv6 tunnel between R1 and R3.
6. Include all IPv6 networks in OSPF area 0 on R1, R3, and R4.
7. Manually configure a router ID of 172.16.4.1 on R4 (this address does not need to be reachable).
8. Remove the OSPFv3 configuration commands from R1, R3, and R4 and configure RIPng to run on these routers using RIP1 as the process name.
# Lab 8-4 IPv6 Challenge Lab# By :Dr Mat IkramYusof CCNP,CCSP,CCNA,CCAI,SCNA,SCSA,SCJP,ITILF################################################################## To get available chassis and NM, run "dynamips -H 7200 &dynamips -H 7201 &" from# the command line in the dynamipsdirectory.And " dynagen Lab1-0"## Available C3600 chassis drivers:# * 3620# * 3640# * 3660################################################################## Available C3600 Network Module drivers:# * NM-1E# * NM-4E# * NM-1FE-TX# * NM-4T# * Leopard-2FE# * NM-16ESW#################################################################
mmap = trueghostios = Truesparsemem = Trueautostart = False
[localhost:7200]
#workingdir = C:\Program Files (x86)\Dynamips\sample_labs\internetworkexpert\workingworkingdir = C:\Program Files (x86)\Dynamips\sample_labs\ccnp1Labs\IPV6\working
[[3640]] # # Specify 3640 IOS image on Windows here: #image = C:\Program Files\Dynamips\images\c3640-jk9o3s-mz.123-14.T7.extracted.bin # # Specify 3640 IOS image on Linux here: # image = /ios/c3640-jk9o3s-mz.123-14.T7.extracted.binimage = C:\Program Files (x86)\Dynamips\images\c3640-jk9o3s-mz.124-5a.bin #ram = 128
disk0 = 0 disk1 = 0 # Choose an idlepc value from the belowidlepc = 0x60610428
########################### # # Define router instances # ###########################
[[ROUTER R1]]model = 3640console = 2001 slot0 = NM-4T
s0/0 = R2 s0/0
[[ROUTER R2]]model = 3640console = 2002 slot0 = NM-4T slot1 = NM-1FE-TX
s0/1 = R3 s0/1
[[ROUTER R3]]model = 3640console = 2003 slot0 = NM-4T slot1 = NM-1FE-TX
s0/0 = R4 s0/0
[[ROUTER R4]]model = 3640console = 2004 slot0 = NM-4T slot1 = NM-1FE-TX
R1 CONFIGURATION
R1#sh runBuilding configuration...
Current configuration : 1325 bytes!version 12.4service timestamps debug date time msecservice timestamps log date time msecno service password-encryption!hostname R1!boot-start-markerboot-end-marker!!No aaa new-model!resource policy!memory-size iomem 5!!Ip cef!
ipv6 unicast-routingipv6cef!
interface Tunnel0no ip addressipv6 address FEC::13:1/112ipv6 address FEC0::13:1/112ipv6 rip RIP1 enabletunnel source Serial0/0tunnel destination 172.16.23.3tunnel mode ipv6ip!interface Loopback0no ip addressipv6 address FEC0::1:1/112ipv6 rip RIP1 enable!interface Serial0/0bandwidth 64ip address 172.16.12.1 255.255.255.0serial restart-delay 0clock rate 64000
no dce-terminal-timing-enableno fair-queue!interface Serial0/1no ip addressshutdownserial restart-delay 0no dce-terminal-timing-enable!interface Serial0/2no ip addressshutdownserial restart-delay 0no dce-terminal-timing-enable!interface Serial0/3no ip addressshutdownserial restart-delay 0no dce-terminal-timing-enable!Route reigrp 1network 172.16.0.0no auto-summary!ip http serverno ip http secure-server!ipv6 router ospf 1log-adjacency-changes!ipv6 router rip RIP1!control-plane!line con 0line aux 0line vty 0 4login!!End
R2 CONFIGURATION
R2#sh runBuilding configuration...
Current configuration : 1055 bytes!version 12.4
service timestamps debug date time msecservice timestamps log date time msecno service password-encryption!hostname R2!boot-start-markerboot-end-marker!
No aaa new-model!resource policy!memory-size iomem 5!Ip cef!
interface Serial0/0bandwidth 64ip address 172.16.12.2 255.255.255.0serial restart-delay 0no dce-terminal-timing-enableno fair-queue!interface Serial0/1bandwidth 64ip address 172.16.23.2 255.255.255.0serial restart-delay 0clock rate 64000no dce-terminal-timing-enable!interface Serial0/2noip addressshutdownserial restart-delay 0no dce-terminal-timing-enable!interface Serial0/3no ip addressshutdownserial restart-delay 0no dce-terminal-timing-enable!interface FastEthernet1/0no ip addressshutdownduplex autospeed auto!
Route reigrp 1network 172.16.0.0no auto-summary!ip http serverno ip http secure-server!control-plane!line con 0line aux 0line vty 0 4login
endR3 CONFIGURATION
R3#sh run
Building configuration...
Current configuration : 1435 bytes
version 12.4
service timestamps debug date time msec
service timestamps log date time msec
no service password-encryption
!
hostname R3
!
boot-start-marker
boot-end-marker
no aaa new-model
resource policy
memory-size iomem 5
ip cef
ipv6 unicast-routing
ipv6cef
!
interface Tunnel0
no ip address
ipv6 address FEC0::13:3/112
ipv6 rip RIP1 enable
tunnel source Serial0/1
tunnel destination 172.16.12.1
tunnel mode ipv6ip
!
interface Loopback0
no ip address
ipv6 address FEC0::3:1/112
ipv6 rip RIP1 enable
!
interface Serial0/0
bandwidth 64
no ip address
ipv6 address FEC0:34::/64 eui-64
ipv6 rip RIP1 enable
serial restart-delay 0
clock rate 64000
no dce-terminal-timing-enable
no fair-queue
!
interface Serial0/1
bandwidth 64
ip address 172.16.23.3 255.255.255.0
serial restart-delay 0
no dce-terminal-timing-enable
!
interface Serial0/2
no ip address
shutdown
serial restart-delay 0
no dce-terminal-timing-enable
!
interface Serial0/3
no ip address
shutdown
serial restart-delay 0
no dce-terminal-timing-enable
!
interface FastEthernet1/0
no ip address
shutdown
duplex auto
speed auto
!
Router eigrp 1
network 172.16.0.0
no auto-summary
!
ip http server
no ip http secure-server
!
ipv6 router ospf 1
log-adjacency-changes
!
ipv6 router rip RIP1
!
control-plane
!
line con 0
line aux 0
line vty 0 4
login
!
!
end
R4 CONFIGURATION
R4#sh run
Building configuration...
Current configuration : 1195 bytes
version 12.4
service timestamps debug date time msec
service timestamps log date time msec
no service password-encryption
hostname R4
boot-start-marker
boot-end-marker
no aaa new-model
resource policy
memory-size iomem 5
ip cef
ipv6 unicast-routing
ipv6cef
!
interface Loopback0
no ip address
ipv6 address FEC0::4:1/112
ipv6 rip RIP1 enable
!
interface Serial0/0
bandwidth 64
no ip address
ipv6 address FEC0:34::/64 eui-64
ipv6 rip RIP1 enable
serial restart-delay 0
no dce-terminal-timing-enable
no fair-queue
!
interface Serial0/1
no ip address
shutdown
serial restart-delay 0
no dce-terminal-timing-enable
!
interface Serial0/2
no ip address
shutdown
serial restart-delay 0
no dce-terminal-timing-enable
!
interface Serial0/3
no ip address
shutdown
serial restart-delay 0
no dce-terminal-timing-enable
!
interface FastEthernet1/0
no ip address
shutdown
duplex auto
speed auto
!
ip http server
no ip http secure-server
!
ipv6 router ospf 1
router-id 172.16.4.1
log-adjacency-changes
!
ipv6 router rip RIP1
!
control-plane
!
line con 0
line aux 0
line vty 0 4
login
!
!
End
--------------------------------------------------------------------------------------------------------------------------------------
RESULT
R1#tclsh
R1(tcl)#foreach address {
+>(tcl)#172.16.12.2
+>(tcl)#172.16.23.2
+>(tcl)#172.16.23.3
+>(tcl)#FEC0::3:1
+>(tcl)#FEC0::4:1
+>(tcl)#} {
+>(tcl)#ping $address }
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 172.16.12.2, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 24/48/64 ms
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 172.16.23.2, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 24/51/76 ms
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 172.16.23.3, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 84/104/128 ms
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to FEC0::3:1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 80/120/160 ms
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to FEC0::4:1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 76/136/200 ms
R1#sh ipv6 route
IPv6 Routing Table - 11 entries
Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP
U - Per-user Static route
I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary
O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2
ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2
C FEC::13:0/112 [0/0]
via ::, Tunnel0
L FEC::13:1/128 [0/0]
via ::, Tunnel0
L FE80::/10 [0/0]
via ::, Null0
C FEC0::1:0/112 [0/0]
via ::, Loopback0
L FEC0::1:1/128 [0/0]
via ::, Loopback0
R FEC0::3:0/112 [120/2]
via FE80::AC10:1703, Tunnel0
R FEC0::4:0/112 [120/3]
via FE80::AC10:1703, Tunnel0
C FEC0::13:0/112 [0/0]
via ::, Tunnel0
L FEC0::13:1/128 [0/0]
via ::, Tunnel0
R FEC0:34::/64 [120/2]
via FE80::AC10:1703, Tunnel0
L FF00::/8 [0/0]
via ::, Null0
R4#sh ipv6 int brief
Serial0/0 [up/up]
FE80::CE03:1AFF:FE24:10
FEC0:34::CE03:1AFF:FE24:10
Serial0/1 [administratively down/down]
unassigned
Serial0/2 [administratively down/down]
unassigned
Serial0/3 [administratively down/down]
unassigned
FastEthernet1/0 [administratively down/down]
unassigned
Loopback0 [up/up]
FE80::CE03:1AFF:FE24:10
FEC0::4:1
R1#ping FEC0:34::CE03:1AFF:FE24:10
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to FEC0:34::CE03:1AFF:FE24:10, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 88/108/128 ms
R3#sh ipv6 route
IPv6 Routing Table - 11 entries
Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP
U - Per-user Static route
I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary
O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2
ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2
R FEC::13:0/112 [120/2]
via FE80::AC10:C01, Tunnel0
L FE80::/10 [0/0]
via ::, Null0
R FEC0::1:0/112 [120/2]
via FE80::AC10:C01, Tunnel0
C FEC0::3:0/112 [0/0]
via ::, Loopback0
L FEC0::3:1/128 [0/0]
via ::, Loopback0
R FEC0::4:0/112 [120/2]
via FE80::CE03:1AFF:FE24:10, Serial0/0
C FEC0::13:0/112 [0/0]
via ::, Tunnel0
L FEC0::13:3/128 [0/0]
via ::, Tunnel0
C FEC0:34::/64 [0/0]
via ::, Serial0/0
L FEC0:34::CE02:1AFF:FE24:10/128 [0/0]
via ::, Serial0/0
L FF00::/8 [0/0]
via ::, Null0