lambda light s - asia.conergy.comasia.conergy.com/wp-content/themes/conergy-child/pdf/lambda...

2
Lambda Light S + Flexible modular system With the Lambda Light S + modules can be installed in South orientation without a penetration of the roof. The Lambda Light S + is available in 10 or 15 degree to allow a layout optimization either in regards to maximum output or maximum number of modules. Through the flexible arrangement of the modules in landscape orientation the load is optimal distributed on the roof. In order to get the minimum possible load on the roof the Lambda Light S + was wind tunnel tested and accordingly optimized. Thanks to the flexible design of the Lambda Light S + it is possible to use the same components for 10 and 15 degree by simply twisting the foot point at the front and the upper part of the rear leg. The proven Clickstone technology for the mod- ule clamping allows a fast and easy installation. Maximum service life All components are made of extruded aluminum and stainless steel. This choice of material guarantees both full recyclability and a maximum service life due to high resistance to corrosion. Orientation landscape South orientation Warranty years Optimized Design! Flat roof Framed module Lambda Light S + Product data sheet

Upload: nguyencong

Post on 30-Aug-2018

235 views

Category:

Documents


0 download

TRANSCRIPT

Page 1: Lambda Light S - asia.conergy.comasia.conergy.com/wp-content/themes/conergy-child/pdf/Lambda Light... · Lambda Light S + Flexible modular system With the Lambda Light S+ modules

Lambda Light S + Flexible modular systemWith the Lambda Light S+ modules can be installed in South orientationwithout a penetration of the roof. The Lambda Light S+ is available in 10 or 15 degree to allow a layout optimization either in regards to maximum output or maximum number of modules.

Through the flexible arrangement of the modules in landscape orientation the load is optimal distributed on the roof. In order to get the minimum possible load on the roof the Lambda Light S+ was wind tunnel tested and accordingly optimized.

Thanks to the flexible design of the Lambda Light S+ it is possible to use the same components for 10 and 15 degree by simply twisting the foot point at the front and the upper part of the rear leg. The proven Clickstone technology for the mod-ule clamping allows a fast and easy installation.

Maximum service lifeAll components are made of extruded aluminum and stainless steel. This choice of material guarantees both full recyclability and a maximum service life due to high resistance to corrosion.

Flat roof

Framed module Orientation

landscape

South orientation

Warrantyyears

Optimized Design!

Flat roof

Framed module

Lam

bd

a L

igh

t S

+ P

rod

uct

dat

a sh

eet

Page 2: Lambda Light S - asia.conergy.comasia.conergy.com/wp-content/themes/conergy-child/pdf/Lambda Light... · Lambda Light S + Flexible modular system With the Lambda Light S+ modules

Lam

bd

a L

igh

t S

+ P

rod

uct

dat

a sh

eet

For further information: www.mounting-systems.com

Subject to technical changes.

2014 © Mounting Systems GmbH

Lam

bd

a-Li

ght-

S+

-TD

-EN

-14

05

Application Flat roofs 1, up to 5 roof slope

Bulding height Depending on wind loads on site

PV modules Framed

Module width 785-1050mm

Module layout Composite (min. 10 m²)

Module orientation Landscape

Pitch 10° or 15°

Size of module array Any size possible, min. 10 m²

Position of the module array No special requirements

Standards Eurocode 1 – Action on structures

Eurocode 9 – Design of aluminium structures 2

Supporting profiles Aluminium (EN AW 6063 T66), (EN AW 6060 T6)

Sheet metal components Galvanised steel (S235 JR)

Small parts Stainless steel (V2A)

Warranty 10 years 3

1 Attention: For any project, please check the static suitability of the building!

2 Official assesible static calculation available on request, at extra cost.

3 Please find the exact terms in the Mounting Systems GmbH warranty document.

Detail front support

Detail back support