laminex® wall panel

LAMINEX® WALL PANELSOLUTIONS

FABRICATION AND INSTALLATION GUIDE

IMPORTANT NOTES

1. Suitable for internal use only

2. Failure to install or maintain this product in accordance with applicable building codes, regulations, standards and

Laminex’s instructions may lead to personal injury, affect system performance, violate building codes and void the

product warranty.

3. Laminex will only warrant the system when used with tested and approved Laminex decorative panels. For Laminex

panels not featured in the matrix, refer to your Laminex Representative for more information.

4. The strength of the system is dependant on the installer ensuring that all fasteners are firmly screwed to framework.

5. All panels should be pre-conditioned on-site for 48 hours before hanging.

RESPONSIBILITY

The specifier or person responsible for the project must ensure that the details in this instruction are appropriate for the

intended application and that additional detailing is performed for details that are not specified in these instructions.

FRAMING

Framing tolerances must be within 3mm over any 3000mm length of the frame. Frame must be square, straight and true.

Timber

All frames must be constructed in accordance with AS/NZS 1684 and be 35mm or wider. Ensure that all fasteners used

penetrate framing by at least 30mm.

Steel

All frames must be constructed in accordance with NASH standard Part 1.

Using Button-Fix over existing internal linings

Ensure that all fasteners used penetrate existing linings and are firmly screwed into studwork by at least 30mm. Laminex

recommends that wooden battens of 35mm x 45mm pine or 16mm MDF are used over existing plaster or masonary wall

linings.

Bracing

Laminex Button-Fix is not suitable for the provision of any bracing load resistance.

HOW IT WORKS

ATTACHING THE BUTTON

Choose an appropriate 5mm counter sunk screw to

provide >30mm engagement into the supporting structure.

NOTE: Plasterboard is not strong enough to support a

Laminex Decorative panel with Button-Fix. Secure Buttons

into studwork or battens only.

IMPORTANT: The integrity of the Laminex Wall Panel Solutions system is dependant on the installer providing a sound

support to the system such as stud work, framing or battens.

TYPE 2 FIX

The Type 2 Fix connects panels at

90° with a simple push/pull fit. It

is ideal for applications where the

emphasis is more on ease of fit

and less on strength. Unlike Type 1,

the Type 2 Fix does not require a

15mm dropdown engagement.

TYPE 1 FIX

The Type 1 Fix connects parallel

panels and is ideal for applications

where strength and security are

paramount.

Engage the Buttons in the Fixes and

slide the panel down by 15mm until

Button-fix goes ‘click’. The Type 1 Fix

can also be configured for sideways

assembly.

When surface-mounted, the Type

1 Fix creates an 8mm gap between

the two attaching panels.

Alternatively, you can rebate the Type

1 Fix, to reduce the gap between the

two attaching panels to only 3mm.

Do not use the REBATE method with Compact Laminate – as this reduces the systems tolerance to changes in panel dimensions as humidity changes.

Ø5mm pan head wood screws for surface-mounted Fix

15mm fall to engage panel

Panel drilling

Ø4.5mm countersunk wood screws for rebated Fix

Lime green Button for use with Ø5mm countersunk wood screw

Orange Button for use with Ø6.2mm Varianta Euro screw

Ø4.5mm pan head wood screws for Fix



Panel drilling







Panel drilling







Panel drilling







Panel drilling







Panel drilling







Panel drilling







Panel drilling





THE SECRET FIXING FOR PANELS

The Button-fix range of fasteners

and accessories is:

BUTTONS

1. Lime green Button for

countersunk (5mm) wood

screws.

2. Orange buttons for Euro

screws/varianta. (Diameter

6.2mm countersunk).

FIXES

3. Type 1 Fix for connecting parallel

panels. (Diameter 5mm pan head

for face fixing. Diameter 4.5mm

countersunk for rebated fixing.)

4. Type 2 Fix for connecting 90°

panels. (Diameter 4.5mm pan

head.)

MARKER ACCESSORIES

5. Button marker accessory for

use with Type 1 Fixes.

6. Fix marker accessory for use

with Type 2 Fixes (and can also

be used with Type 1).

Marker accessories need to be

ordered separately from the

Button-fixes.

OTHER ACCESSORIES

7. Security cord accessory for use

with Type 2 Fixes.

8. Router jig for use when

recessing Type 1 Fixes.

These accessories need to be

ordered separately from the

Button-fixes.

1. 2.

5. 6.

3. 4.

7. 8.

ACCESSORIES

BUTTON MARKER

This re-usable accessory helps to

accurately align the Buttons with

Type 1 Fixes. Snap a marker into

each Fix, then position the second

panel and press firmly. The markers

will leave indents in the panel

surface, which can be used as pilot

guides for the Buttons.

SECURITY CORD ACCESSORY

This accessory should be installed with the Type 2 Fix in situations where safety

is an issue. On a vertical panel install two Security Cords, one to each Fix in the

top corners.

An additional Button is used to capture the loop on the Security Cord, installed

adjacent to the fixing Button. To remove the panel completely, ease the loop on

the Security Cord off the Button.

Please note that accessories must be ordered separately from the Button-fixes.

FIX MARKER

This re-usable accessory helps to

accurately align Type 2 Fixes. The

marker is assembled onto the Fix

and used to position the Button

from the panel edge. After fixing

the Button, position the second

panel and press firmly. The marker

will leave indents in the panel

surface, which can be used as

guides when drilling pilot holes for

the Fix.

The marker can be used for

internally mounted panels, but

must be assembled in the opposite

orientation, as shown on the right.

Tip: use some adhesive tape to

stop the marker and Fix assembly

rotating on the Button.

INSTRUCTIONS FOR USE – TYPE 1 FIX SETS

Button-fix is designed for furniture construction and interior fittings.

Provided that the screws and substrate are properly matched, a vertical panel fixed with four Type 1 Fixes can safely weigh

200kg. For critical applications it is essential to perform your own tests.

Avoid any contact with aggressive solvents and cleaning products.

SUGGESTED LAYOUT– MDF, PB & PLYWOOD

As an approximate guide, we suggest

that Button-fix centres are no greater

than 1000mm apart and no closer

than 35mm to the edge of the panel.

Always remember to allow at least

15mm clearance for the removable

panel to disengage.

Allow 3mm space minimum

between panels.

SUGGESTED LAYOUT– COMPACT LAMINATE

As an approximate guide, we suggest

that Button-fix centres are no greater

than 450mm apart and no closer

than 35mm to the edge of the panel.

Always remember to allow at least

15mm clearance for the removable

panel to disengage.

Allow 5mm space minimum

between panels.



MAX 1000

MAX 1000

MAX 1000



MAX 450

MAX 450

MAX 450

2700

600

2400

1200

Max1000

Max1000

Max300

Max300

2700

600

2400

1200

Max450

Max450

Max200

Max200

2700

600

2400

1200

Max1000

Max1000

Max300

Max300

2700

600

2400

1200

Max450

Max450

Max200

Max200


BUTTON MARKER ACCESSORY

The Button marker accessory helps to mark out where to install the Buttons.

Once you have attached the Fix mouldings (see following pages), snap a marker into each one. Then position the second panel

and press firmly. The markers will leave indents in the panel surface, which can be used as guides for drilling pilot holes for the

Buttons.

Remove the markers, which can be re-used to mark out the next panel.



MAX 1000

MAX 1000

MAX 1000



MAX 1000

MAX 1000

MAX 1000

SURFACE-MOUNTED FIX

Surface mounting creates an 8mm gap between the two panels. The Fix can be configured in three options:

1. BUTTON ON REMOVABLE PANEL

The Fix is attached to the background structure, pointing upwards as shown in the diagrams on the right.

In this configuration, the panels engage vertically and 15mm clearance is required above the removable panel.

2 x Ø5mm pan head wood screws




15mm slide to engage panel

Panel drilling

Panel drilling


Panel drilling






Panel drilling

Panel drilling


Panel drilling






Panel drilling

Panel drilling


Panel drilling


2. FIX ON REMOVABLE PANEL

The Fix is attached to the removable panel, pointing downwards as shown in the diagrams on the right.


3. SIDEWAYS ARRANGEMENT

The Fix is attached to either the background structure or the removable panel, pointing sideways as shown in the diagrams on

the right.

In this configuration, the panels engage horizontally and 15mm clearance is required to the side of the removable panel.

NOTE: Sideways arrangements are NOT suitable for Compact Laminate panels orientated vertically and over 1.2m wide.

Compact Laminate needs to be able to change dimensions as ambient humidity changes.

4. OVERHEAD & CEILING ARRANGEMENTS

Laminex does NOT consider Button-Fix suitable for ceiling or overhead installation of decorative panels.






Panel drilling

Panel drilling


Panel drilling






Panel drilling

Panel drilling


Panel drilling






Panel drilling

Panel drilling


Panel drilling






Panel drilling

Panel drilling


Panel drilling






Panel drilling

Panel drilling


Panel drilling






Panel drilling

Panel drilling


Panel drilling


REBATED FIX

Rebating the Fix creates a 3mm gap between the two panels. The Fix can be configured in three options:

1. BUTTON ON REMOVABLE PANEL

The Fix is attached to the background structure, pointing upwards as shown in the diagrams on the right.


2 x Ø4.5mm countersunk wood screws




Panel drilling



Panel

drilling

Panel

drilling





Panel drilling



Panel

drilling

Panel

drilling





Panel drilling



Panel

drilling

Panel

drilling





Panel drilling



Panel

drilling

Panel

drilling





Panel drilling



Panel

drilling

Panel

drilling





Panel drilling



Panel

drilling

Panel

drilling

2. FIX ON REMOVABLE PANEL

The Fix is attached to the removable panel, pointing downwards as shown in the diagrams on the right.


NOTE: REBATED FIX method is NOT suitable for Compact Laminate mounting. Compact laminate needs air flow on both

sides of the panel and room to change dimensions by ~2.5% as ambient humidity changes.

All battens behind compact laminate must be orientated vertically to allow for ventilation.


A USEFUL TIP

When several Button-fixes are used on a panel or if you require the panel to

be easily removable, you can reduce the strength of the click-fit.

To achieve this adapt some (but not all) the Fix mouldings by popping out

the ears with a flat screw driver, as shown in the diagram on the right. Wear

eye protection and gloves.

BUTTON DIMENSIONS FIX DIMENSIONS

3. SIDEWAYS ARRANGEMENT

The Fix is attached to either the background structure or the removable panel, pointing sideways as shown in the diagrams on

the right.

In this configuration, the panels engage horizontally and 15mm clearance is required to the side of the removable panel.





Panel drilling



Panel

drilling

Panel

drilling





Panel drilling



Panel

drilling

Panel

drilling





Panel drilling



Panel

drilling

Panel

drilling

SUGGESTED JOIN DETAILS

LAP JOIN

LAP JOIN

The following diagrams offer suggestions for panel joins.

SEALED TONGUE AND GROOVE JOIN

Decorative panel

MDF, metal or HPL tongue

Flexible Sealant

Decorative panel

MDF, Metal or HPL tongue

Screw fixing

Decorative panel

HPL or Metal reveal

TONGUE AND GROOVE JOIN

Decorative panel

Paint for MDF & Plywood

CORNER DETAIL

Decorative panel

Screw fixing

HPL or Metal reveal

NOTE: Compact Laminate requires airflow on both sides of the panel and an allowance of 5mm between panels for

expansion and contraction. MDF PB requires 3mm gap between panels. All boards should be pre-conditioned on-site for

48 hours before hanging.

For more information visit laminex.com.au or call 132 136.

Laminex Wall Panel Solutions Button-Fix is marketed and distributed by Laminex ABN 98 004 093 092. The colours of the products featured within the imagery in this brochure are as close to the Laminex Wall Panel Solutions Button-Fix range as photographic lighting and modern printing processes allow. Laminex®, Button-Fix™

2/1

4 T

LG13

01

1. Subject to the conditions and limitations set out in this warranty below, Laminex Group Pty Limited ABN 98 004 093 092 trading as Laminex warrants to the original purchaser of any Laminex® Wall Panel Solutions Button-Fix™ for interior residential or commercial use who is a “consumer” as defined in section 3 of the Australian Consumer Law that Laminex will at its option, repair or replace any Laminex Wall Panel Solutions Button-Fix without charge if it is defective directly as a result of its manufacture by Laminex or it’s suppliers, or the materials used in its manufacture by Laminex or it’s suppliers, during the first seven years after the initial purchase (proof of purchase will be required). Subject to paragraph 7, this obligation terminates at the expiration of 7 years from the date of purchase of the product concerned from Laminex.

2. This warranty does not cover any defect caused by: a) any natural occurrence or any other circumstance beyond Laminex’s control; or b) failure to follow any procedures recommended by Laminex, at the time of

fabrication and installation, for the fabrication and installation of Laminex Wall Panel Solutions Button-Fix; or

c) physical abuse, misuse, accidents, exposure to excessive heat, exposure to excessive moisture, the use of solvents or inappropriate cleaning products/materials, improper maintenance, normal ‘wear and tear’, burns, exposure to chemical products; or

d) general fading and discolouration (exposure to sunlight should be avoided); or e) the product being used in applications that are not recommended by Laminex in the

product literature published; or f) where the defect has been caused by faulty workmanship by any person other

than Laminex; or g) variation in colour, pattern, shade of the material against the sample material, displays

and/or printed illustrations The warranty also does not cover: h) where the defect is trivial or insubstantial; or i) where, as at the date of notification of the defect to Laminex, the defective

product no longer forms part of Laminex’s standard stock range and the person complaining of the defect does not agree to the supply of a replacement which is as close a type as is possible from Laminex’s then prevailing stock range; or

j) anything that has been disclosed as a feature or limitation of Laminex Wall Panel Solutions Button-Fix in any literature published by Laminex; or

k) use of Laminex Wall Panel Solutions Button-Fix with panels other than the recommended Laminex Decorative Panels, as the Laminex Wall Lining system has been tested as a system incorporating appropriate Laminex Decorative Panels;

3. This warranty applies only to Laminex Wall Panel Solutions Button-Fix: a) Purchased from Laminex after 1 July 1994 for interior residential or commercial

use in Australia; b) That has remained installed at the location at which it was first installed after its

sale by Laminex; c) Which has been installed, maintained, used and protected in the manner

recommended by Laminex, as at the relevant time of such installation, maintenance, use or protection, in its literature published from time to time concerning Laminex Wall Panel Solutions Button-Fix, a copy of which may be obtained, free of charge, at the point of purchase or by writing directly to Laminex at the address given below; and

d) where Laminex has been notified of the defect within seven days of the first person to become aware of it.

4. Costs of claiming:a) Laminex will bear the expense of the reasonable labour charges which are necessary

for the repair or replacement of the Laminex Wall Panel Solutions Button-Fix Product covered by this warranty. When submitting a claim, please provide details of the quantum of the labour charges necessary for the repair or replacement of the Laminex Wall Panel Solutions Button-Fix (including any quotes you have obtained verifying the labour charges).

b) If Laminex considers that you have incurred or will incur reasonable labour charges which are necessary for the repair or replacement of the Laminex Wall Panel Solutions Button-Fix covered by this warranty, it will pay you the amount of those charges or pay those charges directly to a third party to undertake the necessary repair or replacement works.

c) Subject to a), the person claiming the warranty will bear all other expenses of claiming the warranty.

5. A replacement product may not be reasonably available from Laminex in the same shape, type or colour as the original Laminex Wall Panel Solutions Button-Fix product covered by this warranty. If a replacement product of the same shape, type or colour is not reasonably available, Laminex reserves the right to provide a replacement product of as close a shape, type and colour match as is reasonably possible from Laminex’s then prevailing product range in satisfaction of its obligations under this warranty.

6. Except as expressly provided in paragraphs 8 and 9, all terms, conditions, warranties, undertakings, inducements and representations, whether express or implied, statutory or otherwise relating in any way to Laminex Wall Panel Solutions Button-Fix are excluded. Without limiting the generality of the preceding sentence, Laminex will not be under any other liability in respect of any loss or damage (including consequential loss or damage) however caused (whether by negligence or otherwise) which may be suffered or incurred or which may arise directly or indirectly in respect of Laminex Wall Panel Solutions Button-Fix.

7. Where any applicable legislation implies any term, condition or warranty into the contract of sale between Laminex and a person, or Laminex’s relationship with a person, which has acquired Laminex Wall Panel Solutions Button-Fix, or otherwise gives that person a particular remedy against Laminex, and that legislation or any legislation voids or prohibits any provision excluding, or modifying the application of, or exercise of, any liability under such term, condition, warranty or remedy, then that term, condition warranty or remedy shall be deemed to be included in or, as the case may be, apply to that contract or relationship. However, Laminex’s liability for any breach of such term, condition or warranty or under such remedy, shall be limited, at Laminex’s option, in any one or more of the ways permitted by that legislation including, where so permitted:

a) If the breach related to Laminex Wall Panel Solutions Button-Fix:i. The replacement of Laminex Wall Panel Solutions Button-Fix or the supply of

equivalent product;ii. The repair of Laminex Wall Panel Solutions Button-Fix;iii. The payment of the cost of replacing Laminex Wall Panel Solutions Button-Fix or

acquiring equivalent product; oriv. The payment of the cost of having Laminex Wall Panel Solutions Button-Fix

repaired; and b) If the breach relates to services: i. The supplying of the services again; or ii. The payment of the cost of having the services supplied again.8. Please note that the benefits given by this warranty are in addition to other rights and

remedies of the person under a law in relation to the goods or services to which this warranty relates. This warranty should not therefore be read as an exclusive statement of the rights of the original purchaser or any other person.

9. Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.

10. This warranty does not cover any other product used or installed in connection with Laminex Wall Panel Solutions Button-Fix.

11. This warranty is not transferable or assignable.12. Any inquiries regarding this warranty should be sent to Laminex Wall Panel Solutions

Button-Fix Warranties, Laminex, P.O. Box 407, Doncaster, VIC 3108. Inquiries can also be made by calling 132 136 or emailing [email protected].

13. To claim this warranty, please send the following written details to the address set out above:• Your name, address and telephone number• Place where the Laminex Wall Panel Solutions Button-Fix Product was purchased

and amount you paid for it. Please also provide a copy of your proof of purchase• If the Laminex Wall Panel Solutions Button-Fix Product has been installed - the

address at which it was installed, the date of installation, the name of the person and company that installed it, the quantum of the labour charges necessary for the repair or replacement of the Laminex Wall Panel Solutions Button-Fix Product (including any quotes you have obtained verifying the labour charges)

• Description of how the Laminex Wall Panel Solutions Button-Fix Product is defective and when you found out that it was defective. Please also provide any photographs taken of the defect(s)

After we receive your written claim, we will contact you to discuss. In some circumstances Laminex may need to remove a sample of the installed Laminex Wall Panel Solutions Button-Fix Product for testing.

7 YEAR WARRANTY

laminex® wall panel

Documents