larnitech catalogue · 5 dw-hc08 8-channel heating controller the device is designed for...
TRANSCRIPT
1
Contents
DIN rail modules Gateways DE-MG - Main gateway
DE-GW - Gateway
actuators DW-LC18 - 18-channel actuator
DW-LC10 - 10-channel actuator
DW-LC07 - 7-channel actuator
DW-DM04 - 4-channel dimmer
DW-DM02 - 2-channel dimmer
DW-HC10 - 10-channel heating controller
DW-HC08 - 8-channel heating controller
DW-RGB03 - 9-channel LED controller
DW-BC03 - 3-channel module for blinds motor control
DW-WL02 - Water leakage protection module
I/o unIts, Interface adapters DW-SW16 - 16-channel adapter for buttons
DW-RS485 - RS485 interface adapter
DW-RS232 - RS232 interface adapter
DW-UART - Serial interface adapter
DW-010 - 4-channel module for 0-10V input devices
DW-DALI - DALI interface controller
DW-DISPATCH - AMR (automatic meter reading) module
Equipment for installation in the pattress box space actuators BW-LC02 - 2-channel actuator
BW-DM - Dimmer
BW-BC-PW - Blinds control module (power)
BW-BC-LC - Blinds control module (low-current)
BW-RGB - 3-channel LED controller
I/o modules and Interface adapters BW-SW06 - 6-channel input module
BW-LSA - Leakage sensor adapter
BW-IO - 6-channel I/O module
BW-NA - NEST adapter
BW-RS485 - RS485 interface adapter
BW-RS232 - RS232 interface adapter
BW-UART - Serial port adapter.
BW-010 - 4-channel module for 0-10V input devices
..3..3..3
..3
..3..3
..4
..4
..4
..4
..4
..5
..5
..5
..5
..6..6
..6
..6
..6
..7
..7
..7
..8..8..8
..8
..8
..8
..9
..9..9
..9
..9
..10
..10
..10
..10
..10
2
sensors CW-HTMLI - 4 in 1 sensor
CW-MLI.A / CW-M.A - Micro-sized 3 in 1 sensor
WW-HTL - Wall 3 in 1 sensor
WW-TS - Wall temperature sensor
FW-TS - Temperature sensor
FW-FT - Underfloor heating temperature sensor
EW-WL - Built-in floor leakage sensor
FW-WL - On-the-floor leakage sensor
Multiroom FE-MP - Media point
FE-IC - Video intercom
METAFORSA series Metaforsa MF-10 - Base unit
DW-HT07 - 7-channel extension module
DW-HT05 - 5-channel extension module
FW-LS - Lighting sensor
..11..11
..11
..11
..11
..12
..12
..12
..12
..13..13
..13
..14..14
..14
..14
..14
3
GatewaysdIn rail modules
De-MG MAIN GATEWAYUsed for accumulation and storage of system data. The device determines the logical scheme of the system, allows authorized access to the system via the Internet. It also converts Ethernet into CAN bus and vice versa. Built-in IR receiver.
Interfacesmax can devicespower supplydimensions
2xCAN, Ethernet40 (20 per CAN)24 VDC6U 104x90x58 mm
aCtuators
De-Gw GATEWAYUsed to connect two additional CAN networks to the system.
Interfacesmax can devicespower supplydimensions
2xCAN, Ethernet40 (20 per CAN)24 VDC2U 35x90x58 mm
Dw-LC18 18-chANNEl AcTuATorDesigned for high power AC/DC circuits commutation. Applicable for non-dimmable light, power sockets, for control of fan coil units, locks, blinds/gates.
output channels quantitymax load per channelconnection typepower supplydimensions
18 (0-250 V AC/DC)8 ACAN24 VDC from CAN9U 156x90x58 mm
4
Dw-LC10 10-chANNEl AcTuATorDesigned for high power AC/DC circuits commutation. Applicable for non-dimmable light, power sockets, control of fan coil units, locks, blinds/gates.
output channels quantitymax load per channelconnection typepower supplydimensions
108 ACAN24 VDC from CAN6U 104x90x58 mm
Dw-LC07 7-chANNEl AcTuATorDesigned for high power AC/DC circuits commutation. Used for non-dimmable light, power sockets and other electrical devices.
output channels quantitymax load per channelconnection typepower supplydimensions
78 A CAN24 VDC from CAN4U 69x90x58 mm
Dw-DM04 4-chANNEl dIMMErDesigned for smooth adjustment of brightness of lighting devices (non reactive load). MOSFET type.
output channels quantityInputmax load per channelconnection typepower supplydimensions
4100 - 250 VAC (50-60 Hz)2 ACAN24 VDC from CAN4U 69x85x58 mm
Dw-DM02 2-chANNEl dIMMErDesigned for smooth adjustment of brightness of lighting devices (non reactive load). MOSFET type.
output channels quantityInputmax load per channelconnection typepower supplydimensions
2100 - 250 VAC (50-60 Hz)4 ACAN24 VDC from CAN4U 69x85x58 mm
10-chANNEl hEATING coNTrollErThe device is designed for controlling heating devices (radiators, floor heating, fan coil units, etc.). The device is equipped with 10 input channels for connection of temperature sensors.
Dw-HC10
output channels quantityInput channels quantitymax load per channelconnection typepower supplydimensions
10 (0-250 V AC/DC)100.5 A (110W at 220V)CAN24 VDC from CAN4U 69x85x58 mm
5
Dw-HC08 8-chANNEl hEATING coNTrollErThe device is designed for controlling heating devices (radiators, floor heating, fan coil units, etc.). The device is equipped with 8 inputs for connection of temperature sensors.
output channels quantityInput channels quantitymax load per channelconnection typepower supplydimensions
8 (0-250V AC/DC)80.5 A (110W at 220V) CAN24 VDC from CAN4U 69x85x58 mm
Dw-rGB03 9-chANNEl lEd coNTrollErAllows connecting RGB and monochrome LED strips.
output channels quantity adjustment typeInputmax load per channelpower supplydimensions
9PWM10-24 VDC1.67 A (20W at 12V)24 VDC from CAN2U 35x90x58 mm
Dw-BC03 3-chANNEl ModulE for blINds MoTor coNTrolProvides control of curtains, projector screens, valves or other electrical motors with force control.
output channels quantitymax load per channelconnection typepower supplydimensions
3 (100-250 VAC)2 ACAN24 VDC from CAN2U 35x90x58 mm
Dw-wL02 WATEr lEAkAGE proTEcTIoN ModulEThe module supports the connection of 2 valves of water supply shutoff and 4 leakage sensors.
output channels quantitynumber of sensor inputsmax load per channelconnection typepower supplydimensions
2 (100-250 VAC)42 ACAN24 VDC from CAN2U 35x90x58 mm
6
I/o unIts, InterfaCe aDapters
Dw-sw16 16-chANNEl AdApTEr for buTToNsCan support up to 15 buttons/reed switches or 8 LED buttons.
Input channels quantityButtons/reed switches led buttonsconnection typepower supplydimensions
1615 8CAN24 VDC from CAN2U 36x90x58 mm
Dw-rs485 rs485 INTErfAcE AdApTErDesigned for interface adjustment between the devices which have the RS485 interface and the Smart Home system.
rs485 ports quantityconnection typepower supplydimensions
1CAN24 VDC from CAN2U 36x90x58 mm
Dw-rs232 rs232 INTErfAcE AdApTErDesigned for interface adjustment between the devices which have the RS232 interface and the Smart Home system.
rs232 ports quantityconnection typepower supplydimensions
1CAN24 VDC from CAN2U 36x90x58 mm
Dw-uart sErIAl INTErfAcE AdApTErDesigned for interface adjustment between the devices which have the UART interface (TTL levels) and the Smart Home system.
uart ports quantityconnection typepower supplydimensions
1CAN24 VDC from CAN2U 36x90x58 mm
7
Dw-010 4-chANNEl ModulE of 0-10V INpuT dEVIcEsAllows connecting devices with 0-10V input interface to the Smart Home system.
output channels quantityconnection typepower supplydimensions
4CAN24 VDC from CAN2U 36x90x58 mm
Dw-DaLI dAlI INTErfAcE coNTrollErAllows controlling DALI devices from the Smart Home system.
dalI ports quantity max output currentconnection typepower supplydimensionsmax dalI devices
2300 mACAN11.5 … 27.5 V DC from CAN2U 35x90x58 mm64 (32 per port)
Dw-DIspatCH AMr (AuToMATIc METEr rEAdING) ModulEThe device for monitoring electricity meters via RS485-bus, heating meters via M-BUS and the pulse water meters.
m-Bus ports quantity rs485 ports quantitypulse inputs quantityconnection typepower supplydimensions
1120CAN11.5 … 27.5 V DC from CAN4U 69x85x58 mm
8
equipment for installation in the pattress box spaceaCtuators
Bw-LC02 2-chANNEl AcTuATorDesigned for AC/DC circuits commutation. Applicable for lighting and other electrical devices. Has 6 input channels for connecting buttons and reed switches.
output channels quantityInput channels quantitymax load per channelconnection typepower supplydimensions
2 (100-250 VAC)62 ACAN24 VDC from CAN45x42x14 mm
Bw-DM dIMMErThis single channel dimmer is designed for smooth control of electrical load (non reactive load). Has 3 input channels for connecting buttons and reed switches. MOSFET type.
output channels quantityInput channels quantitymax load per channelconnection typepower supplydimensions
1 (100-250 VAC, 50-60 Hz)32 ACAN24 VDC from CAN45x42x14 mm
Bw-BC-pw blINds coNTrol ModulE (power)Provides control of curtains, projector screens, valves, or other electrical motors with force control. Has 6 inputs for connecting buttons/reed switches.
output channels quantityInput channels quantitymax load per channelconnection typepower supplydimensions
2 (100-250 VAC)62 ACAN24 VDC from CAN45x42x14 mm
Bw-BC-LC blINds coNTrol ModulE (low-current)Provides control of curtains, projector screens, valves with low-current control. Has 6 inputs for connecting buttons/reed switches.
output channels quantityInput channels quantitymax load per channelconnection typepower supplydimensions
2 (0-50 V AC/DC)60.5 ACAN24 VDC from CAN45x42x14 mm
9
Bw-rGB 3-chANNEl lEd coNTrollErAllows controlling RGB strip or three monochrome LED strips.
output channels quantity adjustment typeInputmax load per channelpower supplydimensions
3PWM10-24 VDC1 A24 VDC from CAN45x42x14 mm
I/o MoDuLes anD InterfaCe aDapters
Bw-sw06 6-chANNEl INpuT ModulEUsed to connect buttons/reed switches.
Input channels quantityconnection typepower supplydimensions
6CAN24 VDC from CAN45x42x14 mm
Bw-Lsa lEAkAGE sENsor AdApTErAllows connecting two leakage sensors, has the function of detecting the presence of the sensor.
Input channels quantityconnection typepower supplydimensions
2CAN24 VDC from CAN45x42x14 mm
Bw-Io 6-chANNEl I/o ModulEThe module is designed for connection of other digital devices which do not have standard interfaces.
Input channels quantityoutput channels quantity connection typepower supplydimensions
33CAN24 VDC from CAN45x42x14 mm
10
Bw-na NEsT AdApTErAdapter for connecting NEST thermostat to the Smart Home system.
Input channels quantityoutputconnection typepower supplydimensions
524 VACCAN24 VDC from CAN45x42x14 mm
Bw-rs485 rs485 INTErfAcE AdApTErDesigned for interface adjustment between the devices which have the RS485 interface and the Smart Home system.
rs485 ports quantityconnection typepower supplydimensions
1CAN24 VDC from CAN45x42x14 mm
Bw-rs232 rs232 INTErfAcE AdApTErDesigned for interface adjustment between the devices which have the RS232 interface and the Smart Home system.
rs232 ports quantityconnection typepower supplydimensions
1CAN24 VDC from CAN45x42x14 mm
Bw-uart sErIAl porT AdApTEr.Designed for interface adjustment between the devices which have the UART interface (TTL levels) and the Smart Home system.
uart ports quantityconnection typepower supplydimensions
1CAN24 VDC from CAN45x42x14 mm
Bw-010 4-chANNEl ModulE for 0-10V INpuT dEVIcEsAllows connecting devices with 0-10V input interface to the Smart Home system.
output channels quantityconnection typepower supplydimensions
4CAN24 VDC from CAN45x42x14 mm
11
sensors
Cw-HtMLI 4 IN 1 sENsorContains motion, lighting, humidity, temperature sensors and an IR transmitter.
connection typepower supplydimensions
CAN24 VDC from CAN80x70x25 mm
Cw-MLI.a / Cw-M.a MIcro-sIzEd 3 IN 1 sENsor Contains motion, lighting (CW-MLI only) sensors and an IR transmitter (CW-MLI only).
connection typepower supply
CAN24 VDC from CAN
ww-HtL WAll 3 IN 1 sENsorContains temperature, lighting, and humidity sensors.
connection typepower supplydimensions
CAN24 VDC from CAN40x40x12 mm
ww-ts WAll TEMpErATurE sENsorWall temperature sensor for DW-HCxx module.
connection typepower supplydimensions
1-wire5 VDC40x40x12 mm
12
fw-ts TEMpErATurE sENsorOpen-frame temperature sensor for DW-HCxx module.
connection typepower supplydimensions
CAN5 VDC5x4x8 mm
fw-ft uNdErfloor hEATING TEMpErATurE sENsor.Underfloor heating temperature sensor for DW-HCxx, can also be used to measure the outdoor temperature.
connection typepower supplycable lengthdimensions
1-wire5 VDC3 m8x8x50 mm
ew-wL buIlT-IN floor lEAkAGE sENsorWater leakage sensor with an alarm light, mountable in the floor surface. Used together with DW-WL or BW-LSA modules.
connection typepower supplydimensions
1-wire9-12 VDC18x18x20 mm
fw-wL oN-ThE-floor lEAkAGE sENsor The sensor is placed on the floor surface. It has an alarm light, which changes from green to red if the sensor detects water on the floor. Used together with DW-WL or BW-LSA modules.
connection typepower supplydimensions
1-wire9-12 VDC50x47x22 mm
13
multiroom
fe-Mp MEdIA poINTMultiroom system media point with a built-in amplifier. Used to play music, the Internet radio, system notifications. Supports DLNA protocol. Can be used either within the Smart Home system or separately.
I/ospeakersoutput powerconnection typepower supplydimensions
2xSpeakers, USB, Ethernet, Line-in4-8 ohm2 x 20WEthernet24 VDC, 4 A140x64x30 mm
fe-IC VIdEo INTErcoMVideo intercom calling panel. Has a built-in 1.3MP camera with IR illumination, a proximity card reader, a relay for connecting the electric lock. Has a built-in 2Gb memory to record photos/video. Supports SIP protocols, DLNA.
protocolsconnection typepower supplydimensions
SIP, DLNAEthernet24 VDC, 1 A153x85x45 mm
14
metaforsa series
Metaforsa Mf-10 bAsE uNITIt is a completely ready-to-install kit of the Smart Home system. The kit includes the main MF-10 unit, 3 motion sensors, 2 FW-WL leakage sensors, 4 FW-TS temperature sensors, 4 reed switches, and a 12V 1,25A PSU.
output channels quantityInput channels quantitymax load per channelconnection typepower supplydimensions
10 (0-250V AC/DC)168 AEthernet12 VDC9U 156x90x58 mm
Dw-Ht07 7-chANNEl ExTENsIoN ModulEHas 7 outputs for connecting loads and 12 inputs for connecting various sensors/buttons.
output channels quantityInput channels quantitymax load per channelconnection typepower supplydimensions
7 (0-250V AC/DC)128 ACAN12-24 VDC from CAN6U 104x85x58 mm
Dw-Ht05 5-chANNEl T ModulEHas 5 outputs for connecting loads and 8 inputs for connecting various sensors/buttons.
output channels quantityInput channels quantitymax load per channelconnection typepower supplydimensions
5 (0-250V AC/DC)88 ACAN12-24 VDC from CAN4U 69x85x58 mm
fw-Ls