laser barcode scanner - icintracom...terminal . 9. run hyper terminal and make the right setting:...

Laser Barcode Scanner

Model no. LS6007 FS5027

User’s Manual

FCC Compliance

This equipment has been tested and found to comply with the limits for a Class A digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio frequency energy and, if

not installed and used in accordance with the instructions manual, may cause harmful

interference to radio communications. Operation of this equipment in a residential area is

likely to cause harmful interference in which case the user will be required to correct the

interference at his own expense.

Changes or modifications not expressly approved by the party responsible for compliance

could void the user‘s authority to operate the equipment.

Limited Warranty

No warranty of any kind is made in regard to this material, including, but not limited to,

implied warranties of merchantability or fitness for any particular purpose. We are not liable

for any errors contained herein or for incidental or consequential damages in connection with

furnishing, performance or use of this material. We shall be under no liability in respect of

any defect arising from fair wear and tear, willful damage, negligence, abnormal working

conditions, failure to follow the instructions and warnings, or misuse or alteration or repair of

the products without written approval.

1

Table of Contents

1. INTRODUCTION……………………………………………………………………………… ..…2~3

2. INSTALLATION………………………………………………………………………………..…...4~7

3. SET UP FROM BAR CODE LABEL………………………………………………………….……..8

Multi-interface Functions……….………………………………………………………9~11

Interface-Serial……..……………………………………………………………………12~13

1D Symbologies On/Off……………………………………………………………….14~15

2D Symbologies On/Off…………………………………………………………………….16

Symbologies Set Up…………………………………………………………………….17~21

Termination String Setup Bar Codes…………………………………………………..22

2

Introduction

3

RIOTEC LS6007 FS5027 2D Laser barcode scanner, using Intermec engine, combines the

best scanning performance and value. The device provides an accurate, easy, and fast method

of data entry and data storage for computerized information systems. It is easy to install

drivers to operate.

RIOTEC LS6007 FS5027 2D laser barcode scanner can compatible several interfaces

(RS232-USB, RS-232,) and numerous configurations, is a powerful and reliable handheld

scanner without compromise.

All the operating parameters are programmed by bar code programming menu and stored in

non-volatile RAM which can retain the settings after power is turned off.

When a barcode is successful decoded, the blue LED light of the scanner will turn on and off.

The scanner will beep once.

LED (blue/red)

Exit Window

Trigger

Buzzer

Handle

Buzzer

Exit Window

LED

4

Installation Insert the plug on the free end of the Communications Cable into the appropriate connector on

the host as below described:

1. USB cable Connection:

Reset Configuration to Defaults

If you are unsure of the scanner configuration or have scanned the incorrect codes,

please scan the “Reset Configuration to Defaults” barcode below . This will reset the

scanner to its factory defaults settings in USB interface.

2. RS232 cable Connection:

Connect with host

connect with host

Require 5V adapter for power supply

5

NOTE: for Serial port (RS232 cable), please plug the power connector of 5V power

adapter to RS232 cable.

1. Be sure that Host computer is turned OFF

2. Connect scanner cable to the USB port(COM port) on the host system.

3. .Ensure that all connections are secure. Turn on your host.

4. And please operate the scanner under the right software application.

5. Install the software “PL-2303 Driver Installer.exe” to the host system..

6. Go to My Computer � One click right button of mouse � Administrate �

Device Administrator � Connect Port (COM and LPT).

7. Choose Prolific USB-to-Serial Com Port, and see identify COM number, ex.

COM 5.

8. Go to START � Programs � Accessories � Communications �� Hyper

Terminal .

9. Run Hyper Terminal and make the right setting: 9600, 8-data bits, NONE-parity,

1-stop bit, NONE-flow control.

10. Aim the scanner at a barcode, ensure that the scanner is in trigger mode (default),

and press the trigger.

11. On successful decode, the blue LED light will turn on and off. The scanner will

beep once. And will show the bar code data on the screen.

Detail set up on the Hyper Terminal, please see at the Figure 1 to Figure 3.

6

Reset Configuration to Defaults

If you are unsure of the scanner configuration or have scanned the incorrect codes,

please scan the “Reset Configuration to Defaults” barcode. This will reset the scanner to

its factory defaults settings.

Please read following 2 barcode to reset to defaults.

Load All Factory Default

【【【【Pro CMD：：：：0001000】】】】

Save as User Default

【【【【Pro CMD：：：：0001150】】】】

Load User Default

【【【【Pro CMD：：：：0001160】】】】

7

If USB(HID) VERSION,PLEASE SET THE OUT PUT MODE AS USB(HID)

Operation

12. Be sure that Host computer is turned OFF.

13. Ensure that all connections are secure.

14. Turn on your host. And please operate the scanner under the right software

application, such as Notepad or Word(RS232 interface should be under

Hyper Terminal” and make the right setting).

15. Aim the scanner at a barcode, ensure that the scanner is in trigger mode (default),

and press the trigger.

16. On successful decode, the blue LED light will turn on and off. The scanner will

beep once.

Tip

Do not hold the scanner directly over a barcode at 90˚. Scanning light bounces directly back into the scanner from the barcode label is known as specular reflection which will create a "dead zone" where decoding is difficult. Practice a few times to find what range of angles works best.

Maintenance

Cleaning the scan window is the only maintenance required. A dirty window may affect scanning accuracy. Wipe the scanner window gently with a lens tissue or other material suitable for cleaning optical material. Do not spray water or other cleaning liquids directly onto the window.

8

Setup from Bar Code Label

9

Multi-Interface Functions

Please read following 2 barcode to reset to defaults.

RESET CONFIGURATION TO DEFAULTS

Save as User Default

【【【【Pro CMD：：：：0001150】】】】

Load User Default

【【【【Pro CMD：：：：0001160】】】】

Operating settings

** Hand-held Mode

Sensor Mode

Pro CMD：0302000 Pro CMD：0302010

Continuous Mode

Pro CMD：0302020

** Code Programming OFF

【Pro CMD：0006000】

** Code Programming ON 【Pro CMD：0006010】

10

** Code Programming ON

【【【【Pro CMD：：：：0006010】】】】 ** Code Programming OFF

【【【【Pro CMD：：：：0006000】】】】

Sensor Mode Timeout

Sensor Mode

** High Sensitivity (= 4)

Pro CMD：0313000 Pro CMD：0312020

Normal Sensitivity (= 7)

Low Sensitivity (= 10)

Pro CMD：0312010

Pro CMD：0312000

Enhanced Sensitivity (= 1)

Program Sensitivity

Pro CMD：0312030

Pro CMD：0312040

11

Allow Reading All = enable to read all symbologies and programming codes

ProhibitProhibitProhibitProhibit Reading All = allow reading programming codes only.

Pro CMD：0001020 Pro CMD：0001010

Allow Reading All 1D

Prohibit Reading All 1D

Pro CMD：0001040 Pro CMD：0001030

Allow Reading All 2D

Prohibit Reading All 2222D

Pro CMD：0001060 Pro CMD：0001050


【Pro CMD：0006000】


12

Interface – Serial - 1

SERIAL BAUD RATE - 2400

BAUD RATE


Pro CMD：0100010 Pro CMD：0100020



Pro CMD：0100030 Pro CMD：0100040

SERIAL BAUD RATE -19200


Pro CMD：0100050 Pro CMD：0100060



Pro CMD：0100070 Pro CMD：0100080


【Pro CMD：0006000】


13

Interface – Serial - 2

SERIAL DATA BITS - 8

PARA- METERS

SERIAL DATA BITS - 6

Pro CMD：0103030 Pro CMD：0103010

SERIAL DATA BITS - 7 SERIAL DATA BITS - 5

Pro CMD：0103020 Pro CMD：0103000

SERIAL STOP BITS - 1

SERIAL STOP BITS - 2

Pro CMD：0102000 Pro CMD：0102010

SERIAL PARITY - NONE

SERIAL PARITY - ODD

Pro CMD：0101000 Pro CMD：0101020

SERIAL PARITY - EVEN

Pro CMD：0101010


【Pro CMD：0006000】


14

1D Symbologies On/Off - 1

CODE 39 ENABLE CODE 39

CODE 39 DISABLE

Pro CMD：0408020 Pro CMD：0408010

CODE 93 - ENABLE

CODE 93

CODE 93 - DISABLE

Pro CMD：0410020 Pro CMD：0410010

CODE 128 - ENABLE CODE 128

CODE 128 - DISABLE

Pro CMD：0400020 Pro CMD：0400010

CODABAR - ENABLE CODABAR

CODABAR - DISABLE

Pro CMD：0409020 Pro CMD：0409010

I 2OF5 - ENABLE INTERLEAVED

2 OF 5

I 2OF5 - DISABLE


【Pro CMD：0006000】


15

Pro CMD：0405020 Pro CMD：0405010

CHINA POST 25 - ENABLE China post 2 5

CHINA POST 25 - DISABLE

Pro CMD：0406020 Pro CMD：0406010

16

1D Symbologies On/Off – 2

UPC-A ENABLE UPC/EAN

UPC-A DISABLE

Pro CMD：0404020 Pro CMD：0404010

UPC-E ENABLE

UPC-E DISABLE

Pro CMD：0403020 Pro CMD：0403010

EAN-8 ENABLE

EAN-8 DISABLE

Pro CMD：0401020 Pro CMD：0401010

EAN-13 ENABLE

EAN-13 DISABLE

Pro CMD：0402020 Pro CMD：0402010

EAN-128 ENABLE UUC/EAN

EAN-128 DISABLE

Pro CMD：0412020 Pro CMD：0412010


【Pro CMD：0006000】


17



【【【【Pro CMD：：：：0006000】】】】

2D Symbologies On/Off - 1

Data Matrix -ENABLE Data Matrix

Data Matrix -DISABLE

Pro CMD：0504020 Pro CMD：0504010

**Forward Direction Barcode Only Both

Pro CMD: 0504320 Pro CMD:0504322

Backward Direction Barcode Only

Pro CMD：0504321

QR Code -ENABLE

QR Code QR Code -DISABLE

Pro CMD：0502020 Pro CMD：0502010

Enable Chinese-Sensible Code Chinese-Sensible

Code

Disable Chinese-Sensible Code

Pro CMD：0508020 Pro CMD：0508010

Aztec -ENABLE Aztec

Aztec -DISABLE

18

Pro CMD：0503020 Pro CMD：0503010

PDF 417ENABLE PDF 417

PDF 417 DISABLE

Pro CMD：0501020 Pro CMD：0501010 **Forward Direction Barcode Only Both

Pro CMD:0501320 Pro CMD:0501322

Backward Direction Barcode Only

Pro CMD:0501321

Symbologies Set Up - 1

CODE 128 CHECK DIGIT –ENABLE

CODE 128 CHECK DIGIT

CODE 128 CHECK DIGIT -DISABLE

Pro CMD：0400150 Pro CMD：0400160

TRANSMIT UCC/EAN-8

CHECK –ENABLE

UCC/EAN -8 CHECK BYTE

TRANSMIT UCC/EAN-8

CHECK –DISABLE

Pro CMD：0401040 Pro CMD：0401030

19

TRANSMIT UCC/EAN-13

CHECK –ENABLE

UCC/EAN -13 CHECK BYTE

TRANSMIT UCC/EAN-13

CHECK –DISABLE

Pro CMD：0402040 Pro CMD：0402030

TRANSMIT UPC-E

CHECK –ENABLE

UPC-E CHECK BYTE

TRANSMIT UPC-E

CHECK –DISABLE

Pro CMD：0403040 Pro CMD：0403030

TRANSMIT UPC-A

CHECK –ENABLE

UPC-A CHECK BYTE

TRANSMIT UPC-A

CHECK –DISABLE

Pro CMD：0404040 Pro CMD：0404030



【【【【Pro CMD：：：：0006000】】】】

NO Check, Transmit All Interleaved 2 of 5 CHECK BYTE

Check, Transmit No Check

Pro CMD：0405050 Pro CMD：0405060

Check, Transmit All

Pro CMD：0405070

NO Check, Transmit All CHINA POST 25 CHECK BYTE


20

Pro CMD：0406050 Pro CMD：0406060

Check, Transmit All

Pro CMD：0406070

NO Check, Transmit All CODE 39

CHECK BYTE


Pro CMD：0408050 Pro CMD：0408060

Check, Transmit All

Pro CMD：0408070



【【【【Pro CMD：：：：0006000】】】】

NO Check, Transmit All CODEBAR

CHECK BYTE


Pro CMD：0409050 Pro CMD：0409060

Check, Transmit All

Pro CMD：0409070

21

NO Check, Transmit All

CODE 93 CHECK BYTE


Pro CMD：0410050 Pro CMD：0410060

Check, Transmit All

Pro CMD：0409070

22

Symbologies Set Up – 2

EXPAND UPC-E TO UPC-A ENABLE

UPC/EAN

FORMATING

EXPAND UPC-E TO UPC-A DISABLE

Pro CMD：0401100 Pro CMD：0401090

Expand to UPC-A ENABLE

Expand to UPC-A DISABLE

Pro CMD：0403120 Pro CMD：0403110

2 Digits Addenda ENABLE UCC/EAN-8

Addenda Code

2 Digits Addenda DISABLE

Pro CMD：0401060 Pro CMD：0401050

5 Digits Addenda ENABLE


Pro CMD：0401070 Pro CMD：0401080

2 Digits Addenda ENABLE UCC/EAN-13 Addenda Code


Pro CMD：0402060 Pro CMD：0402050




【Pro CMD：0006000】


23

Pro CMD：0402080 Pro CMD：0402070

24

Symbologies Set Up – 3


UPC-E Addenda Code


Pro CMD：0403060 Pro CMD：0403050



Pro CMD：0403080 Pro CMD：0403070

2 Digits Addenda ENABLE UPC-A

Addenda Code


Pro CMD：0404060 Pro CMD：0404050



Pro CMD：0404080 Pro CMD：0404070


【Pro CMD：0006000】


25

TERMINATION STRING SETUP BAR CODES

Step 1 STRING# 1

TERMINATION CHAR - CR

Step 2

Pro CMD：0310000 Pro CMD：0309010

Step3

Pro CMD：0000160

STRING# 1

TERMINATION CHAR - LF

Step 1

Step 2

Pro CMD：0310000 Pro CMD：0309000

Step 3


【Pro CMD：0006000】


26

Pro CMD：0000160

27

Version: 1.0 Date: MAY 27, 2009 P/N: 79.60301.011

laser barcode scanner - icintracom...terminal . 9. run hyper terminal and make the right setting:...

Documents