lastec articulatorgateway.lastec.com/manuals/parts/325e97mas.pdf · 2009. 1. 8. · chapter 8:...
TRANSCRIPT
-
Chapter 8: Parts Manual Parts Manual
8-1
Chapter Eight
LasTec ArticulatorModel 325E-97
Master Parts Manual
LasTec8180 West 10th Street
Indianapolis, Indiana 46214Phone (317) 273-1122 Fax (317) 271-4223
Toll-Free (800) 515-6798 http://www.lastec.com
LasTecA Division of Wood-Mizer Products, Inc.
7865 N County Rd 100ELizton, Indiana 46149
Phone (317) 892-4444 Fax (317) 892-4188www.lastec.com
-
This Page
Has Been
Intentionally
Left Blank
1 LASTEC
-
Chapter 8: Parts Manual How To Use This Parts Manual
8-3
How To Use This Parts Manual
Fig. 2.01 Assembly IllustrationSerial Number
From 1010392 1080492 2651292 7570694 8160894 8781194To 1070392 2641292 7560694 8150894 8771194 Present
Ref No. Part No. Part No. Part No. Part No. Part No. Part No. Part Description1 F120 F120 F120 F120 F120 F120 1"-8 Nylock Nut2 F168 (*1) F168 (*1) F168 (*1) F168 F168 F168 1" SAE Flat Washer3 P109 P109 P109 P109 P109 P109 Bronze Bushing, 1" ID4 Not Used Not Used Not Used P247 Not Used Not Used 90 Degree Street Elbow, 1/2" NPT5 W134 W134 W134 W134 Gearbox Channel Weldment, HCM66/SGCM500
W206 W206 Gearbox Channel Weldment , CM413A6 F121 F121 F121 F121 F121 F121 Bolt, 1/2-13 x 1 1/4"7 F122 F122 F122 F122 F122 F122 1/2" Split Lock Washer8 P196-M (*2) P196-M (*2) P196-M P196-M (*3) P196-M (*4) Gearbox, HCM66SCR12, StBv, Splined
P300 Gearbox, SGCM500SAR21, SpBv, Splined9 L128-M (*5) L128-M (*5) L128-M (*5) L128-M (*5) L128-M (*5) L128-M Gearbox Swivel Cover, Universal10 P171 Drive Pulley, Single Groove, BK140H
P130 P130 P130 P130 P130 Drive Pulley, Double Groove, 2BK140H11 P131 (*6) P131 (*6) P131 (*6) P131 (*6) P131 (*6) Split Taper Bushing, 1 1/4" ID x H
P281 (*6) Split Taper Bushing, 1 3/8" ID x H12 F187 F187 F187 F187 F187 F187 Bolt, HH, 1/4-20 x 3/4", G813 P208 (*7) P208 (*7) P208 (*8) P208 (*8) P208 (*8) Pillow Block Bearing, 1 1/4" ID, SSC
P282 (*8) Pillow Block Bearing, 1 3/8" ID, SSC14 F178 F178 F178 F178 F178 F178 Set Screw, 5/16-24 x 5/16", Nylock15 P108 (*9) P108 (*9) Grease Zerk, 1/8" NPT, Straight
P107 P107 P107 P107 Grease Zerk, 1/4-28, Straight16 W135 W135 W135 W135 Slide Bar Weldment - HCM66SCR12
W205 W205 Slide Bar Weldment - CM413A17 P107 P107 P107 P107 P107 P107 Grease Zerk, 1/4-28, Straight18 P146 P146 P146 P146 P146 P146 Drive Belt, B-49 Insta-Power
(*1) Originally P115 & P116 Brass & Zinc Wear Washers, have been replaced with F168 1" SAE Flat Washers. P115 & P116 are nolonger available.
NOTE: The location of these washers may vary depending on model.
(*2) Originally P129-M Gearbox, which utilized the P148 PTO Shaft, which are both no longer available. If converting from a P129-M toa P196-M, you will also need to order either a P225 PTO Shaft or a P207 Splined Yoke to upfit your existing PTO shaft.
(*3) Originally P220 Gearbox, has been replaced with the P196-M Gearbox. The P220 is no longer available. If converting from a P220to a P196-M, you will also need to order (1) W134 Gearbox Channel Weldment and (1) W135 Slide Bar Weldment.
(*4) Originally P250 Gearbox, has been replaced with the P196-M The P250 is no longer available. If converting from a P250 to aP196-M you will also need to order (1) W134 Gearbox Channel Weldment and (1) W135 Slide Bar Weldment.
(*5) Originally L109-M Swivel Cover, has been replaced with the P128-M Universal Swivel Cover. The L109-M is no longer available.
(*6) P131 & P281 each include (2) F187 1/4-20 x 3/4" G8 Bolts.
(*7) Originally P132 Pillow Block with Eccentric Lock Collar. If converting to P208, new mounting hardware will also be needed. (SeeFig. 2.03 for listing.) Also, P208 includes (1) F178 5/16-24 x 5/16" Nylock Set Screw and (1) P107 1/4-28 Straight Grease Zerk.
(*8) P208 Includes (1) F178 5/16-24 x 5/16" Nylock Set Screw and (1) P107 1/4-28 Straight Grease Zerk.
(*9) Used only with P132 Pillow Block Bearing.
Part NumbersThis is the part number you should
use when ordering the part.
Not UsedIf, due to an engineering change, an
illustrated part is discontinued orreplaced, the term “Not Used”
appears in the column under theappropriate serial numbers.
FootnotesChanges which may include important information have
footnotes (*1) listed next to the corresponding part number.Please be sure to read and understand these notes, as they willaid you in identifying and ordering the correct parts for the serial
number series of your Articulator.
Part DescriptionThis is the part description you
should use when ordering the part.
Reference NumbersParts shown in the corresponding
Illustration will each post a referencenumber. Find this reference number
on the spreadsheet for properinformation about that part.
Serial NumbersEngineering changes made to the Articulator aretracked by serial number. If a change affects a
part in the illustration, serial number breakdownsindicating when the change was implemented are
listed at the top of the spreadsheet. Assembly IllustrationThis references the proper
illustration which corresponds withthe spreadsheet
-
Chapter 8: Parts Manual How To Use This Parts Manual
8-4
For your convenience, we have compiled two indexes of all illustrated Articulator parts and the illustration(s) inwhich they appear. These indexes are contained in the following section of this manual. The first index of parts islisted in order by part number, followed by an index of parts listed in order by part description. Simply locate thepart number or description in either index, and turn to the corresponding illustration number(s) to view the part forphysical verification and/or actual application(s).
-
Chapter 8: Parts Manual Index Of Parts Listed By Part
8-6
Index Of Parts Listed By Part Number
Part No. Part Description Illustration Number(s)
019241 Grass Chute Mount Plate, Bottom E-1.08019252 Trap Door, Universal E-1.07019303 Spring, Extension, 1” x 7” E-1.05019303 Spring, Extension, 1” x 7” E-1.06019520 Emergency Brake Front Tie Strap E-3.09019538 Kick Stand Strap, Long E-7.03A149 Wheel/Rim Assembly, 9” x 3.5”, UF E-2.05A150 Wheel Assembly, 9” x 3.5”, UF E-2.04 E-2.05A617 Wheel Yoke Assembly, Fixed Rear, Left E-2.04A618 Wheel Yoke Assembly, Fixed Rear, Right E-2.04A619 Wheel Yoke Assembly, Left E-2.04A620 Wheel Yoke Assembly, Right E-2.04A639 Wheel Yoke Assembly, 13", Right E-2.02A640 Wheel Yoke Assembly, 13", Left E-2.02A685 Control Arm Assembly, Main, Left E-3.01A686 Control Arm Assembly, Main, Right E-3.01A687 Control Arm Assembly, Rear, Right E-3.02A688 Control Arm Assembly, Rear, Left E-3.02A689 Control Assembly, Foot, Right E-3.03A690 Control Assembly, Foot, Left E-3.03A691 Hydraulic Pivot/Centering Arm Assy, RT E-3.04A692 Hydraulic Pivot/Centering Arm Assy, LF E-3.04A693 Hydraulic Centering Arm Assembly, RT E-3.04A694 Hydraulic Centering Arm Assembly. LF E-3.04A695 Hydraulic Pivot Arm Assembly, Right E-3.04A696 Hydraulic Pivot Arm Assembly, Left E-3.04A697 Tie Rod Assembly, Rear E-3.05A698 Tie Rod Assembly, Front E-3.05A699 Tie Rod Assembly, Hydraulic, Left E-3.05A700 Tie Rod Assembly, Hydraulic, Right E-3.05A701 Throttle/Choke Cable Assembly, 26” E-3.06A702 Control Rod Assembly, Throttle E-3.06A703 Control Rod Assembly, Choke E-3.06A704 Deck Lift Handle Assembly, Left E-3.07A705 Deck Left Handle Assembly, Right E-3.07C602 Rubber Clamp Strip E-1.07C613 Fuel Line, 1/4” x 12” E-4.03C614 Fuel Line, 1/4” x 3 1/2” E-4.03C646 Hydraulic Hose, 3/8” x 12” E-5.03C676 Hydraulic Hose, 3/8” x 30” E-5.03C678 Fuel Line, 1/4” x 30” E-4.03C689 Hydraulic Hose, 3/8” x 26” E-5.03
019236 Operator Present Switch Block E-6.03019245 Hydraulic Hose, 3/8” x 9” E-5.03C768 Emergency Brake Tie Rod E-3.09C771 Fuel Line, 1/4” x 18” E-4.03C791 Chain, Deck Lift, Right, 7 1/2" E-3.07C871 Chain Mount Extension Plate E-3.07C873 Chain, Deck Lift, Left, 5 3/4" E-3.07
F05004-112 Stud, 5/16-24 x 3/4”, Press-In E-2.05F05004-133 Bolt, Allen Head, 10-32 x 5/8” E-4.01F05004-134 Bolt, 6mm x 1.0 x 22mm E-4.01F05004-135 Bolt, HHW, 10-32 x 5/8” E-4.01F05004-136 Screw, SFH, 6-32 x 3/4” E-6.07F05004-137 Screw, SFH, 8-32 x 3/4” E-6.07F05004-138 Screw, SFH, 10-32 x 3/8” E-6.07F05004-139 Screw, Phillips Pan Head, 5/32” x 1/2” E-6.07F05004-141 Screw, Shield E-4.01F05004-35 Screw, Button Head, 10-24 x 1/2” E-3.06F05005-101 Bolt, 1/4-20 x 1” E-1.07 E-1.08 E-2.04F05005-116 Bolt, 1/4-20 x 1 1/4” E-5.01F05005-129 Bolt, 1/4-20 x 3/4” E-5.02 E-6.01 E-7.01
-
Chapter 8: Parts Manual Index Of Parts Listed By Part
8-7
Part No. Part Description Illustration Number(s)F05005-47 Screw, Set, 1/4-20 x 3/8” E-6.03F05005-79 Bolt, 1/4-20 x 1/2” E-5.04F05006-1 Bolt, 5/16-18 x 1” E-7.02
F05006-40 Screw, Set, 5/16-18 x 3/8” E-5.01F05006-5 Bolt, 5/16-18 x 3/4” E-6.04
F05006-76 Bolt, 5/16-18 x 1 1/2” E-5.03F05006-78 Bolt, 5/16-18 x 7 1/4” E-5.01F05006-79 Bolt, 5/16-18 x 2” E-5.01F05006-80 Bolt, 5/16-18 x 2 1/2” E-5.03F05006-86 Bolt, Carriage, 5/16-18 x 3/4” E-6.08F05006-89 Bolt, Button Head, 5/16-18 x 1 1/2” E-4.01F05006-92 Bolt, Allen Head, 5/16-18 x 1/2” E-6.05F05006-97 Bolt, Wing, 5/16-18 x 3/4” E-7.01F05007-1 Bolt, 3/8-16 x 3” FT E-2.03
F05007-122 Bolt, 7/16-20 x 2 1/4” E-4.01F05007-126 Bolt, 3/8-16 x 4” E-5.01F05007-143 Bolt, 3/8-24 x 1 1/2” E-1.03F05007-147 Bolt, 3/8-16 x 3/4” E-7.03F05007-47 Bolt, 3/8-16 x 2 1/2” E-3.07F05007-78 Bolt, 3/8-16 x 1 1/2” E-3.04 E-3.07 E-3.07F05007-87 Bolt, 3/8-16 x 1” E-5.02F05008-10 Bolt, 1/2-13 x 2 1/4”, G8 E-1.05 E-1.06F05009-62 Bolt, 5/16-18 x 1 1/4” E-3.07F05009-80 Bolt, 5/8-18 x 2 1/4” E-1.02 E-1.03F05009-81 Bolt, 3/4 -10 x 2 1/8” E-1.01F05010-1 Nut, Hex, 3/8-16 E-3.04 E-3.06 E-5.01
F05010-10 Nut, Nylock, 3/8-16 E-3.04 E-3.07 E-5.02F05010-103 Nut, Nylock, 3/4-10 E-2.04F05010-122 Nut, Half Nylock, 3/4-10 E-1.01 E-1.05 E-1.06F05010-123 Nut, Hex, 3/8-24 E-3.05 E-6.04F05010-124 Nut, Half Nylock, 3/8-16 E-3.04 E-3.07 E-3.09F05010-127 Nut, Half Nylock, 1/2-13 E-5.04F05010-133 Nut, Hex, 8-32 E-6.07F05010-139 Nut, Hex, 7/8-14 E-1.02F05010-142 Nut, Lug, 1/2-20 x 13/16” E-2.05F05010-144 Nut, Flanged, 6mm x 1.25 E-4.01F05010-145 Nut, Jam, 9/16-18 E-6.05F05010-17 Nut, Hex, 5/16-18 E-4.01 E-6.08 E-7.02F05010-18 Washer, Flat, #10 SAE E-6.07F05010-24 Nut, Wing, 3/8-16 E-1.04F05010-35 Nut, Hex, 1/2-13 E-3.01F05010-44 Nut, Hex, 6-32 E-6.07F05010-50 Nut, Half Nylock, 5/16-18 E-6.05F05010-58 Nut, Nylock, 5/16-18 E-3.07 E-5.01 E-5.03F05010-63 Nut, Hex, 1/4-20 E-2.05F05010-69 Nut, Nylock, 1/4-20 E-1.08 E-3.06 E-3.09F05010-72 Nut, Hex, 1/2-20 E-6.04 E-3.06F05010-8 Nut, Nylock, 1/2-13 E-1.05 E-1.06 E-3.08
F05011-11 Washer, Flat, 1/4” SAE E-3.09 E-5.01 E-6.01F05011-13 Washer, Split Lock, 5/16” E-4.01 E-5.01 E-6.04F05011-14 Washer, Split Lock, 1/4” E-1.07 E-2.05 E-5.01F05011-16 Washer, Flat, 5/16” E-3.07 E-5.03F05011-17 Washer, Flat, 5/16” SAE E-4.01 E-5.01 E-7.02F05011-18 Washer, Flat, #10 E-4.01F05011-2 Washer, Flat, 1/2” SAE E-1.05 E-1.06 E-6.04
F05011-27 Washer, Split Lock, 5/8” E-1.02 E-1.03F05011-29 Washer, Flat, 3/4” E-7.04F05011-3 Washer, Flat, 3/8” E-1.03 E-2.03 E-3.04 E-7.03
F05011-35 Washer, Flat, 7/16” E-6.03F05011-4 Washer, Split Lock, 3/8” E-1.03 E-2.03 E-3.04 E-3.05 E-3.06 E-5.01
F05011-44 Washer, Fender, 3/8” E-1.04F05011-46 Washer, Split Lock, 7/8” E-1.02F05011-48 Washer, Split Lock, 7/16” E-4.01F05011-6 Washer, Split Lock, 3/4” E-7.04
F05011-60 Washer, Flat, 1/4” E-1.07 E-1.08F05011-61 Washer, Flat, 3/8” SAE E-3.07 E-5.01 E-5.02F05011-62 Washer, Flat, 3/4” SAE E-1.01 E-2.04 E-3.01 E-3.03 E-3.07 E-3.08F05011-68 Washer, Flat, 1/2” E-1.03 E-2.01 E-3.08 E-5.04
-
Chapter 8: Parts Manual Index Of Parts Listed By Part
8-8
Part No. Part Description Illustration Number(s)F05011-72 Washer, Flat, 1/4” SAE E-7.01F05011-73 Washer, Flat, 7/8” SAE E-1.02F05011-80 Washer, Rubber, 1/2” E-6.04F05011-9 Washer, Split Lock, 1/2” E-2.01 E-6.04F05012-1 Cotter Pin, 1/8” x 1” E-1.08 E-3.09
F05012-23 Cotter Pin, 3/16” x 2 1/2” E-3.07F05012-63 Hitch Pin, #216 E-1.08F05013-70 Bolt, 3/4-10 x 6 1/2” E-2.04F05013-71 Bolt, 3/4-10 x 2” E-3.08F05013-72 Bolt, 3/4-16 x 1 1/2” E-7.04
F412 Screw, Operator Present E-6.06L316 Seat Spacer Plate E-7.02L377 Neutral Start Switch Mounting Plate E-6.05M205 Oil Cooler Cover E-5.03M210 Fender, Outer E-7.01M215 Deck Lift Link Arm E-3.07M218 Screw, Hydraulic Pivot Arm Locking E-3.04M220 Turnbuckle Guard E-3.08M221 Fan Spacer E-5.01M225 Pivot Guard, E1 E-1.07M226 Pivot Guard, E3 E-1.07M230 Grass Chute E-1.08M235 Delrin Pad, 1 3/4” x 2” E-5.04P105 O-Ring, 2 1/2” ID x 2 3/4” OD E-1.02 E-1.03P107 Grease Zerk, 1/4-28, Straight E-2.02 E-3.03 E-3.08 E-7.04 E-5.04P108 Grease Zerk, 1/8” NPT, Straight E-1.02 E-1.03P109 Bushing, Bronze, 1" ID x 1 1/4" E-2.02 E-2.03 E-2.04 E-3.08 E-7.04
P110-M Clevis Pin, 3/8” x 1 5/16” E-2.04P111 Kick-Out Ring, 1" E-2.04 E-3.03 E-3.07P113 Lynch Pin, 1/4" E-2.02 E-3.01 E-3.02 E-3.08 E-5.04 E-7.04P114 Lynch Pin, 3/16” E-2.03P118 Decal, Die-Cut, “LasTec” E-7.06P119 Decal, Die-Cut, “Articulator” E-7.06P123 Grease Zerk, 1/4-28, 90° E-1.05 E-1.06 E-2.03 E-3.07P151 Snapper Pin, 3/8” x 2 3/4” E-3.08P183 Clevis Pin, 1” x 4 1/2” E-3.08P184 Clevis Pin, 1” x 5 1/4” E-7.04P190 Bearing, 1” Tapered Roller E-2.02P191 Bearing Seal E-2.02P194 Nut, Lug, 1/2-20 x 13/16” Tapered E-2.01P195 Hub Cap E-2.02P289 Bearing Race Insert E-2.02P290 Wheel/Rim Assembly, DM E-2.05P291 Wheel Hub/Bearing Assy, 3/4” TRB, DM E-2.05P292 Bearing, 3/4” Tapered Roller E-2.05P293 Bearing Seal, 3/4” TRB E-2.05P294 Grease Zerk, 1/4-28, 45° E-2.05P296 Bearing Spacer, 3/4” x 1/2” E-2.04P297 Wheel Hub Assembly, DM E-2.05P402 Bearing Race Insert, 3/4” TRB E-2.05P403 Bushing, bronze, 3/4” ID x 5/8” E-1.01 E-1.05 E-1.06 E-3.01 E-3.02 E-3.03 E-3.07 E-5.04P407 Key, 3/16” SQ x 5/8” E-1.02 E-1.03P433 Bearing Washer, 3/4” E-2.02P434 Nut, Castle, 3/4-16 E-2.02P436 Bushing, bronze, 3/8" x 1" E-1.08 E-3.04P447 Cotter Pin, 1/8” x 1 1/2” E-2.02P460 Spring, Torsion, 180°, LH E-1.08P464 Spring, Extension, 1 1/8” x 7 1/2” E-5.04P465 Tire, 13", Pneumatic E-2.02P475 Decal, Warning, “Avoid Injury”, Front E-7.06P476 Decal, Warning, “Avoid Injury”, Rear E-7.06P477 Decal, Warning, “Thrown Objects” E-7.06P478 Decal, Warning, “Rotating Blades” E-7.06P479 Decal, Choke E-7.06P480 Decal, Throttle E-7.06P481 Decal, Hydraulic Oil E-7.06P482 Decal, Deck Release E-7.06P484 Decal, Control, Forward/Back E-7.06
-
Chapter 8: Parts Manual Index Of Parts Listed By Part
8-9
Part No. Part Description Illustration Number(s)P485 Decal, Fuel E-7.06P486 Decal, Main Control E-7.06P487 Decal, Rear Control E-7.06P491 Decal, Emergency Brake E-7.06P493 Decal, Warning, “Clear Area” E-7.06P601 Idler Pulley, 7" E-5.04P602 Switch, Ignition E-6.01P603 Pulley, 7” E-4.01P604 Clutch, electric E-4.01P606 Hydraulic Cooling Fan E-5.01P607 Belt, Insta-Power 851030 E-4.01P608 Idler Pulley, Flat E-1.05 E-1.06P609 Idler Pulley, V-Groove E-1.05 E-1.06P610 Pulley, 7” x 15mm E-5.01P611 Cup Holder E-7.01P612 Bushing, bronze, 1 1/2” ID x 1 1/2” E-7.04P613 Hydrostatic Transmission Unit, Right E-5.01P614 Hydrostatic Transmission Unit, Left E-5.01P615 Axle, ZT, Left E-5.01P616 Axle, ZT, Right E-5.01P619 Oil Filter Manifold E-5.02 E-5.03P620 Oil Filter E-5.02 E-5.03P621 Oil Cooler E-5.03P622 Deck Lift Handle E-3.07P623 Handle, Tapered, Black E-3.01 E-3.06P624 Hose Clamp E-5.03P625 Battery, 12V E-6.08P626 Light, Flasher E-6.04P627 Spring, 9/16” x 5” E-3.04P628 Spring, Weight Transfer, 24” E-7.05P629 Grip, Black E-3.03 E-3.08 E-3.09P630 Seat E-7.02P631 Hydraulic Oil Tank, 2 Quart E-5.02 E-5.03P632 Battery Terminal Cover, Red E-6.08P634 Bushing, Plastic, 1/2” Split E-3.06 E-3.09P635 Grip, Hand, Black E-3.02P636 Headlight E-6.04P638 Oil Filter E-4.01P641 Cable Clamp E-3.06P645 Hydraulic Fitting, 90°, 3/8” HB x 7/16-20 E-5.01P646 Hydraulic Fitting, 90°, 3/8” E-5.03P648 Hydraulic Fitting, 3/8” HB x 7/8-14 ORB E-5.01P649 Hose Clamp, 7/16” - 5/8” E-4.02 E-4.03P650 Spring Pin, 3/8" E-3.05P651 Rod End, 3/8-24, Female E-3.05P652 Switch, Momentary ON/Momentary OFF E-6.02P653 Flasher E-6.07P654 Switch, OFF/Momentary ON E-6.01P656 Switch, ON/OFF E-6.01 E-6.02P657 Relay E-6.07P662 Circuit Board E-6.07P665 Fuse, 3 Amp E-6.07P666 Fuse, 10 Amp E-6.07P677 Cable, Battery, 52”, Red E-6.08P682 Grommet, 5/8" E-6.07P683 Light, Warning E-6.01P684 Meter E-6.01P685 Pulley, Drive, 8” Deep Groove E-1.03P686 Yoke, 3/8-24 E-3.05P687 Tire, Pneumatic, 20/10X8BTL E-2.01P688 Tie Rod, Rear E-3.05P690 Tie Rod, Front E-3.05P691 Tie Rod, Hydraulic, Right E-3.05P692 Tie Rod, Hydraulic, Left E-3.05P698 Switch, Operator Present E-6.03P699 Rubber Deck Seal E-1.07P701 Blade, 25”, High-Lift E-1.02 E-1.03P703 T-Fitting, 1/4” E-4.03
-
Chapter 8: Parts Manual Index Of Parts Listed By Part
8-10
Part No. Part Description Illustration Number(s)P705 Operator Present Switch Bar E-6.03P706 Belt, Insta-Power, 85890 E-1.04 E-5.04P707 Belt, Insta-Power, 85870 E-1.04P708 Spacer Hub E-2.01P709 Clevis Pin, 5/16” x 1 1/2” E-3.07P723 Key, 3/16” SQ x 1 1/2” E-1.03P724 Key, 1/4” SQ x 1” E-4.01P725 Key, 5MM SQ x 3/4” E-5.01P726 Fuse Box E-6.07P103 Bearing, Spindle, Top E-1.02 E-1.03 E-1.02 E-1.03P736 Kohler Engine, 25HP E-4.01P741 Spacer E-6.07P742 Knob, Plastic, 10-32 x 3/8” E-6.07P743 Cable, Battery, 42”, Black E-6.08P747 Hydraulic Oil Tank Cap E-5.02P748 Seat Slide Track E-7.02P766 Hydraulic Pump Mount Spacer, E-5.01P767 Bearing Spacer E-5.01P768 Bearing, Ball, 15mm x 35mm x 11mm E-3.04 E-5.01P769 Retainer Ring E-5.01P770 Input Gear E-5.01P771 O-Ring E-5.01P772 Switch, Neutral Start E-6.05P773 Bushing, Rubber, 3/8” Flanged E-4.02P774 Air Filter E-4.01P775 Spark Plug, Champion 12-132-02 E-4.01P780 Rod End, 3/8-24, Female, Shielded E-3.05P805 Fuel Tank, 5 Gallon E-4.02 E-4.03P808 Washer, Shim, 1 1/8” x 1 5/8” x 1/8” E-4.01P809 Dip Stick E-4.01P810 O-Ring E-4.01P811 Fan Guard E-4.01P812 Air Filter Sleeve E-4.01P813 Air Filter Retainer Cap E-4.01P814 Air Filter Nut, 6mm x 1.0 E-4.01P815 Air Filter Cover E-4.01P816 Muffler E-4.01P817 Muffler Guard E-4.01P818 Cable Clamp E-4.01P820 Gas Cap E-4.02P821 Fuel Valve, 3/8” x 1/4” E-4.02P822 Fuel Filter E-4.03P826 Switch, Operator Present E-6.06P828 Coupler, Hex, 10-32 x 2” E-6.07P833 Gasket, Exhaust E-4.01T104 Wheel Spacer, 1/4” E-2.04T107 Wheel Spacer, 1” E-2.04T126 Bearing Spacer, 3/4” x 11/16” E-2.04T153 Turnbuckle, 3/4-16 E-3.08T154 Turnbuckle Shoulder Bolt E-3.08T156 Pulley, Double, XS/ES E-1.02 E-1.03T157 Spindle, Keyed, XS/ES E-1.02T180 Spindle Spacer, 1” E-1.02 E-1.03T212 Spindle, E2, Keyed E-1.03T215 Spacer, 3/8” ID x 3/4” E-3.07W353 Turnbuckle End Weldment, 1" Right E-3.08W354 Turnbuckle End Weldment, 1/2" Left E-3.08W610 Side Leg Weldment, E1 E-2.03W611 Side Leg Weldment, E3 E-2.03W612 Pull Bar Weldment E-7.04W613 Axle Weldment, Front E-7.04W614 Wheel Yoke Weldment, Fixed Rear, LF E-2.04W615 Wheel Yoke Weldment, Fixed Rear, RTt E-2.04W619 Control Arm Weldment, Main, Right E-3.01W620 Control Arm Weldment, Main, Left E-3.01W621 Pedal Weldment, Foot, Right E-3.03W622 Pedal Weldment, Foot, Left E-3.03W623 Throttle/Choke Mount Weldment, Front E-3.06
-
Chapter 8: Parts Manual Index Of Parts Listed By Part
8-11
Part No. Part Description Illustration Number(s)W625 Throttle Mount Weldment, Rear E-3.06W626 Choke Mount Weldment, Rear E-3.06W627 Weight Transfer Pivot Arm Wldmnt, RT E-3.07W628 Weight Transfer Pivot Arm Wldmnt, LF E-3.07W629 Control Rod Weldment, Throttle/Choke E-3.06W631 Idler Arm Weldment, Low E-1.05W632 Idler Arm Weldment, High E-1.06W633 Grass Chute Mount Weldment E-1.08W634 Deck Lift Foot Pedal Weldment E-3.08W635 Wheel Yoke Weldment, 13", Left E-2.02W636 Wheel Yoke Weldment, 13", Right E-2.02W637 Hydraulic Pivot Arm Weldment, Left E-3.04W638 Hydraulic Pivot Arm Weldment, Right E-3.04W640 Hydraulic Centering Arm Weldment, RT E-3.04W641 Hydraulic Centering Arm Weldment, LF E-3.04W645 Light Box Weldment, Left E-6.04W646 Light Box Weldment, Right E-6.04W647 Seat Pan Weldment E-7.02 E-7.03W648 Pull Pin Weldment E-7.04W649 Emergency Brake Handle Weldment E-3.09W653 Hydraulic Centering Arm Mount Wldmnt, LF E-3.04W654 Hydraulic Centering Arm Mount Wldmnt, RT E-3.04W659 Emergency Brake Pivot Rod Weldment E-3.09W660 Fender, Inside, Left E-7.01W661 Fender, Inside, Right E-7.01W662 Control Panel Weldment, Main E-6.01W663 Oil Cooler Mount Weldment E-5.03W664 Wheel Yoke Weldment, Right E-2.04W665 Wheel Yoke Weldment, Left E-2.04W666 Side Leg Pivot Pin Weldment E-2.03W667 Weight Transfer Pivot Rod Weldment E-3.07W669 Control Arm Weldment, Rear, Right E-3.02W670 Control Arm Weldment, Rear, Left E-3.02W671 Pulley Cover Weldment, E1 E-1.04W672 Pulley Cover Weldment, E3 E-1.04W678 Kick Stand Weldment, Short E-7.03W684 Idler Arm Weldment, Mule Drive E-5.04W691 Mulching Plate Weldment E-1.08
-
Chapter 8: Parts Manual Index Of Parts Listed By Part Description
8-12
Index Of Parts Listed By Part Description
Part No. Part Description Illustration Number(s)
P774 Air Filter E-4.01P815 Air Filter Cover E-4.01P814 Air Filter Nut, 6mm x 1.0 E-4.01P813 Air Filter Retainer Cap E-4.01P812 Air Filter Sleeve E-4.01W613 Axle Weldment, Front E-7.04P615 Axle, ZT, Left E-5.01P616 Axle, ZT, Right E-5.01P632 Battery Terminal Cover, Red E-6.08P625 Battery, 12V E-6.08P289 Bearing Race Insert E-2.02P402 Bearing Race Insert, 3/4” TRB E-2.05P191 Bearing Seal E-2.02P293 Bearing Seal, 3/4” TRB E-2.05P767 Bearing Spacer E-5.01P296 Bearing Spacer, 3/4” x 1/2” E-2.04T126 Bearing Spacer, 3/4” x 11/16” E-2.04P433 Bearing Washer, 3/4” E-2.02P190 Bearing, 1” Tapered Roller E-2.02P292 Bearing, 3/4” Tapered Roller E-2.05P768 Bearing, Ball, 15mm x 35mm x 11mm E-3.04 E-5.01P103 Bearing, Spindle, Top E-1.02 E-1.03 E-1.02 E-1.03P607 Belt, Insta-Power 851030 E-4.01P707 Belt, Insta-Power, 85870 E-1.04P706 Belt, Insta-Power, 85890 E-1.04 E-5.04P701 Blade, 25”, High-Lift E-1.02 E-1.03
F05008-10 Bolt, 1/2-13 x 2 1/4”, G8 E-1.05 E-1.06F05005-116 Bolt, 1/4-20 x 1 1/4” E-5.01F05005-79 Bolt, 1/4-20 x 1/2” E-5.04F05005-101 Bolt, 1/4-20 x 1” E-1.07 E-1.08 E-2.04F05005-129 Bolt, 1/4-20 x 3/4” E-5.02 E-6.01 E-7.01F05009-81 Bolt, 3/4 -10 x 2 1/8” E-1.01F05013-71 Bolt, 3/4-10 x 2” E-3.08F05013-70 Bolt, 3/4-10 x 6 1/2” E-2.04F05013-72 Bolt, 3/4-16 x 1 1/2” E-7.04F05007-78 Bolt, 3/8-16 x 1 1/2” E-3.04 E-3.07 E-3.07F05007-87 Bolt, 3/8-16 x 1” E-5.02F05007-47 Bolt, 3/8-16 x 2 1/2” E-3.07F05007-147 Bolt, 3/8-16 x 3/4” E-7.03F05007-1 Bolt, 3/8-16 x 3” FT E-2.03
F05007-126 Bolt, 3/8-16 x 4” E-5.01F05007-143 Bolt, 3/8-24 x 1 1/2” E-1.03F05006-76 Bolt, 5/16-18 x 1 1/2” E-5.03F05009-62 Bolt, 5/16-18 x 1 1/4” E-3.07F05006-1 Bolt, 5/16-18 x 1” E-7.02
F05006-80 Bolt, 5/16-18 x 2 1/2” E-5.03F05006-79 Bolt, 5/16-18 x 2” E-5.01F05006-5 Bolt, 5/16-18 x 3/4” E-6.04
F05006-78 Bolt, 5/16-18 x 7 1/4” E-5.01F05009-80 Bolt, 5/8-18 x 2 1/4” E-1.02 E-1.03F05004-134 Bolt, 6mm x 1.0 x 22mm E-4.01F05007-122 Bolt, 7/16-20 x 2 1/4” E-4.01F05004-133 Bolt, Allen Head, 10-32 x 5/8” E-4.01F05006-92 Bolt, Allen Head, 5/16-18 x 1/2” E-6.05F05006-89 Bolt, Button Head, 5/16-18 x 1 1/2” E-4.01F05006-86 Bolt, Carriage, 5/16-18 x 3/4” E-6.08F05004-135 Bolt, HHW, 10-32 x 5/8” E-4.01F05006-97 Bolt, Wing, 5/16-18 x 3/4” E-7.01
P612 Bushing, bronze, 1 1/2” ID x 1 1/2” E-7.04P109 Bushing, Bronze, 1" ID x 1 1/4" E-2.02 E-2.03 E-2.04 E-3.08 E-7.04P403 Bushing, bronze, 3/4” ID x 5/8” E-1.01 E-1.05 E-1.06 E-3.01 E-3.02 E-3.03 E-3.07 E-5.04P436 Bushing, bronze, 3/8" x 1" E-1.08 E-3.04
-
Chapter 8: Parts Manual Index Of Parts Listed By Part Description
8-13
Part No. Part Description Illustration Number(s)P634 Bushing, Plastic, 1/2” Split E-3.06 E-3.09P773 Bushing, Rubber, 3/8” Flanged E-4.02P641 Cable Clamp E-3.06P818 Cable Clamp E-4.01P743 Cable, Battery, 42”, Black E-6.08P677 Cable, Battery, 52”, Red E-6.08C873 Chain, Deck Lift, Left, 5 3/4" E-3.07C791 Chain, Deck Lift, Right, 7 1/2" E-3.07C871 Chain Mount Extension Plate E-3.07W626 Choke Mount Weldment, Rear E-3.06P662 Circuit Board E-6.07P183 Clevis Pin, 1” x 4 1/2” E-3.08P184 Clevis Pin, 1” x 5 1/4” E-7.04
P110-M Clevis Pin, 3/8” x 1 5/16” E-2.04P709 Clevis Pin, 5/16” x 1 1/2” E-3.07P604 Clutch, electric E-4.01A685 Control Arm Assembly, Main, Left E-3.01A686 Control Arm Assembly, Main, Right E-3.01A688 Control Arm Assembly, Rear, Left E-3.02A687 Control Arm Assembly, Rear, Right E-3.02W620 Control Arm Weldment, Main, Left E-3.01W619 Control Arm Weldment, Main, Right E-3.01W670 Control Arm Weldment, Rear, Left E-3.02W669 Control Arm Weldment, Rear, Right E-3.02A690 Control Assembly, Foot, Left E-3.03A689 Control Assembly, Foot, Right E-3.03W662 Control Panel Weldment, Main E-6.01A703 Control Rod Assembly, Choke E-3.06A702 Control Rod Assembly, Throttle E-3.06W629 Control Rod Weldment, Throttle/Choke E-3.06P447 Cotter Pin, 1/8” x 1 1/2” E-2.02
F05012-1 Cotter Pin, 1/8” x 1” E-1.08 E-3.09F05012-23 Cotter Pin, 3/16” x 2 1/2” E-3.07
P828 Coupler, Hex, 10-32 x 2” E-6.07P611 Cup Holder E-7.01P479 Decal, Choke E-7.06P484 Decal, Control, Forward/Back E-7.06P482 Decal, Deck Release E-7.06P119 Decal, Die-Cut, “Articulator” E-7.06P118 Decal, Die-Cut, “LasTec” E-7.06P491 Decal, Emergency Brake E-7.06P485 Decal, Fuel E-7.06P481 Decal, Hydraulic Oil E-7.06P486 Decal, Main Control E-7.06P487 Decal, Rear Control E-7.06P480 Decal, Throttle E-7.06P475 Decal, Warning, “Avoid Injury”, Front E-7.06P476 Decal, Warning, “Avoid Injury”, Rear E-7.06P493 Decal, Warning, “Clear Area” E-7.06P478 Decal, Warning, “Rotating Blades” E-7.06P477 Decal, Warning, “Thrown Objects” E-7.06A705 Deck Left Handle Assembly, Right E-3.07W634 Deck Lift Foot Pedal Weldment E-3.08P622 Deck Lift Handle E-3.07A704 Deck Lift Handle Assembly, Left E-3.07M215 Deck Lift Link Arm E-3.07M235 Delrin Pad, 1 3/4” x 2” E-5.04P809 Dip Stick E-4.01
019520 Emergency Brake Front Tie Strap E-3.09W649 Emergency Brake Handle Weldment E-3.09W659 Emergency Brake Pivot Rod Weldment E-3.09C768 Emergency Brake Tie Rod E-3.09P811 Fan Guard E-4.01M221 Fan Spacer E-5.01W660 Fender, Inside, Left E-7.01W661 Fender, Inside, Right E-7.01M210 Fender, Outer E-7.01P653 Flasher E-6.07
-
Chapter 8: Parts Manual Index Of Parts Listed By Part Description
8-14
Part No. Part Description Illustration Number(s)P822 Fuel Filter E-4.03C613 Fuel Line, 1/4” x 12” E-4.03C771 Fuel Line, 1/4” x 18” E-4.03C614 Fuel Line, 1/4” x 3 1/2” E-4.03C678 Fuel Line, 1/4” x 30” E-4.03P805 Fuel Tank, 5 Gallon E-4.02 E-4.03P821 Fuel Valve, 3/8” x 1/4” E-4.02P726 Fuse Box E-6.07P666 Fuse, 10 Amp E-6.07P665 Fuse, 3 Amp E-6.07P820 Gas Cap E-4.02P833 Gasket, Exhaust E-4.01M230 Grass Chute E-1.08
019241 Grass Chute Mount Plate, Bottom E-1.08W633 Grass Chute Mount Weldment E-1.08P294 Grease Zerk, 1/4-28, 45° E-2.05P123 Grease Zerk, 1/4-28, 90° E-1.05 E-1.06 E-2.03 E-3.07P107 Grease Zerk, 1/4-28, Straight E-2.02 E-3.03 E-3.08 E-7.04 E-5.04P108 Grease Zerk, 1/8” NPT, Straight E-1.02 E-1.03P629 Grip, Black E-3.03 E-3.08 E-3.09P635 Grip, Hand, Black E-3.02P682 Grommet, 5/8" E-6.07P623 Handle, Tapered, Black E-3.01 E-3.06P636 Headlight E-6.04
F05012-63 Hitch Pin, #216 E-1.08P624 Hose Clamp E-5.03P649 Hose Clamp, 7/16” - 5/8” E-4.02 E-4.03P195 Hub Cap E-2.02A693 Hydraulic Centering Arm Assembly, RT E-3.04A694 Hydraulic Centering Arm Assembly. LF E-3.04W653 Hydraulic Centering Arm Mount Wldmnt, LF E-3.04W654 Hydraulic Centering Arm Mount Wldmnt, RT E-3.04W641 Hydraulic Centering Arm Weldment, LF E-3.04W640 Hydraulic Centering Arm Weldment, RT E-3.04P606 Hydraulic Cooling Fan E-5.01P648 Hydraulic Fitting, 3/8” HB x 7/8-14 ORB E-5.01P646 Hydraulic Fitting, 90°, 3/8” E-5.03P645 Hydraulic Fitting, 90°, 3/8” HB x 7/16-20 E-5.01C646 Hydraulic Hose, 3/8” x 12” E-5.03C689 Hydraulic Hose, 3/8” x 26” E-5.03C676 Hydraulic Hose, 3/8” x 30” E-5.03
019245 Hydraulic Hose, 3/8” x 9” E-5.03P747 Hydraulic Oil Tank Cap E-5.02P631 Hydraulic Oil Tank, 2 Quart E-5.02 E-5.03A696 Hydraulic Pivot Arm Assembly, Left E-3.04A695 Hydraulic Pivot Arm Assembly, Right E-3.04W637 Hydraulic Pivot Arm Weldment, Left E-3.04W638 Hydraulic Pivot Arm Weldment, Right E-3.04A692 Hydraulic Pivot/Centering Arm Assy, LF E-3.04A691 Hydraulic Pivot/Centering Arm Assy, RT E-3.04P766 Hydraulic Pump Mount Spacer, E-5.01P614 Hydrostatic Transmission Unit, Left E-5.01P613 Hydrostatic Transmission Unit, Right E-5.01W632 Idler Arm Weldment, High E-1.06W631 Idler Arm Weldment, Low E-1.05W684 Idler Arm Weldment, Mule Drive E-5.04P601 Idler Pulley, 7" E-5.04P608 Idler Pulley, Flat E-1.05 E-1.06P609 Idler Pulley, V-Groove E-1.05 E-1.06P770 Input Gear E-5.01P724 Key, 1/4” SQ x 1” E-4.01P723 Key, 3/16” SQ x 1 1/2” E-1.03P407 Key, 3/16” SQ x 5/8” E-1.02 E-1.03P725 Key, 5MM SQ x 3/4” E-5.01
019538 Kick Stand Strap, Long E-7.03W678 Kick Stand Weldment, Short E-7.03P111 Kick-Out Ring, 1" E-2.04 E-3.03 E-3.07P742 Knob, Plastic, 10-32 x 3/8” E-6.07
-
Chapter 8: Parts Manual Index Of Parts Listed By Part Description
8-15
Part No. Part Description Illustration Number(s)P736 Kohler Engine, 25HP E-4.01W645 Light Box Weldment, Left E-6.04W646 Light Box Weldment, Right E-6.04P626 Light, Flasher E-6.04P683 Light, Warning E-6.01P113 Lynch Pin, 1/4" E-2.02 E-3.01 E-3.02 E-3.08 E-5.04 E-7.04P114 Lynch Pin, 3/16” E-2.03P684 Meter E-6.01P816 Muffler E-4.01P817 Muffler Guard E-4.01W691 Mulching Plate Weldment E-1.08L377 Neutral Start Switch Mounting Plate E-6.05P434 Nut, Castle, 3/4-16 E-2.02
F05010-144 Nut, Flanged, 6mm x 1.25 E-4.01F05010-127 Nut, Half Nylock, 1/2-13 E-5.04F05010-122 Nut, Half Nylock, 3/4-10 E-1.01 E-1.05 E-1.06F05010-124 Nut, Half Nylock, 3/8-16 E-3.04 E-3.07 E-3.09F05010-50 Nut, Half Nylock, 5/16-18 E-6.05F05010-35 Nut, Hex, 1/2-13 E-3.01F05010-72 Nut, Hex, 1/2-20 E-6.04 E-3.06F05010-63 Nut, Hex, 1/4-20 E-2.05F05010-1 Nut, Hex, 3/8-16 E-3.04 E-3.06 E-5.01
F05010-123 Nut, Hex, 3/8-24 E-3.05 E-6.04F05010-17 Nut, Hex, 5/16-18 E-4.01 E-6.08 E-7.02F05010-44 Nut, Hex, 6-32 E-6.07F05010-139 Nut, Hex, 7/8-14 E-1.02F05010-133 Nut, Hex, 8-32 E-6.07F05010-145 Nut, Jam, 9/16-18 E-6.05F05010-142 Nut, Lug, 1/2-20 x 13/16” E-2.05
P194 Nut, Lug, 1/2-20 x 13/16” Tapered E-2.01F05010-8 Nut, Nylock, 1/2-13 E-1.05 E-1.06 E-3.08
F05010-69 Nut, Nylock, 1/4-20 E-1.08 E-3.06 E-3.09F05010-103 Nut, Nylock, 3/4-10 E-2.04F05010-10 Nut, Nylock, 3/8-16 E-3.04 E-3.07 E-5.02F05010-58 Nut, Nylock, 5/16-18 E-3.07 E-5.01 E-5.03F05010-24 Nut, Wing, 3/8-16 E-1.04
P621 Oil Cooler E-5.03M205 Oil Cooler Cover E-5.03W663 Oil Cooler Mount Weldment E-5.03P620 Oil Filter E-5.02 E-5.03P638 Oil Filter E-4.01P619 Oil Filter Manifold E-5.02 E-5.03P705 Operator Present Switch Bar E-6.03
019236 Operator Present Switch Block E-6.03P771 O-Ring E-5.01P810 O-Ring E-4.01P105 O-Ring, 2 1/2” ID x 2 3/4” OD E-1.02 E-1.03W622 Pedal Weldment, Foot, Left E-3.03W621 Pedal Weldment, Foot, Right E-3.03M225 Pivot Guard, E1 E-1.07M226 Pivot Guard, E3 E-1.07W612 Pull Bar Weldment E-7.04W648 Pull Pin Weldment E-7.04W671 Pulley Cover Weldment, E1 E-1.04W672 Pulley Cover Weldment, E3 E-1.04P603 Pulley, 7” E-4.01P610 Pulley, 7” x 15mm E-5.01T156 Pulley, Double, XS/ES E-1.02 E-1.03P685 Pulley, Drive, 8” Deep Groove E-1.03P657 Relay E-6.07P769 Retainer Ring E-5.01P651 Rod End, 3/8-24, Female E-3.05P780 Rod End, 3/8-24, Female, Shielded E-3.05C602 Rubber Clamp Strip E-1.07P699 Rubber Deck Seal E-1.07
F05004-35 Screw, Button Head, 10-24 x 1/2” E-3.06M218 Screw, Hydraulic Pivot Arm Locking E-3.04F412 Screw, Operator Present E-6.06
-
Chapter 8: Parts Manual Index Of Parts Listed By Part Description
8-16
Part No. Part Description Illustration Number(s)F05004-139 Screw, Phillips Pan Head, 5/32” x 1/2” E-6.07F05005-47 Screw, Set, 1/4-20 x 3/8” E-6.03F05006-40 Screw, Set, 5/16-18 x 3/8” E-5.01F05004-138 Screw, SFH, 10-32 x 3/8” E-6.07F05004-136 Screw, SFH, 6-32 x 3/4” E-6.07F05004-137 Screw, SFH, 8-32 x 3/4” E-6.07F05004-141 Screw, Shield E-4.01
P630 Seat E-7.02W647 Seat Pan Weldment E-7.02 E-7.03P748 Seat Slide Track E-7.02L316 Seat Spacer Plate E-7.02W666 Side Leg Pivot Pin Weldment E-2.03W610 Side Leg Weldment, E1 E-2.03W611 Side Leg Weldment, E3 E-2.03P151 Snapper Pin, 3/8” x 2 3/4” E-3.08P741 Spacer E-6.07P708 Spacer Hub E-2.01T215 Spacer, 3/8” ID x 3/4” E-3.07P775 Spark Plug, Champion 12-132-02 E-4.01T180 Spindle Spacer, 1” E-1.02 E-1.03T212 Spindle, E2, Keyed E-1.03T157 Spindle, Keyed, XS/ES E-1.02P650 Spring Pin, 3/8" E-3.05P627 Spring, 9/16” x 5” E-3.04P464 Spring, Extension, 1 1/8” x 7 1/2” E-5.04
019303 Spring, Extension, 1” x 7” E-1.05019303 Spring, Extension, 1” x 7” E-1.06P460 Spring, Torsion, 180°, LH E-1.08P628 Spring, Weight Transfer, 24” E-7.05
F05004-112 Stud, 5/16-24 x 3/4”, Press-In E-2.05P602 Switch, Ignition E-6.01P652 Switch, Momentary ON/Momentary OFF E-6.02P772 Switch, Neutral Start E-6.05P654 Switch, OFF/Momentary ON E-6.01P656 Switch, ON/OFF E-6.01 E-6.02P698 Switch, Operator Present E-6.03P826 Switch, Operator Present E-6.06P703 T-Fitting, 1/4” E-4.03W625 Throttle Mount Weldment, Rear E-3.06A701 Throttle/Choke Cable Assembly, 26” E-3.06W623 Throttle/Choke Mount Weldment, Front E-3.06A698 Tie Rod Assembly, Front E-3.05A699 Tie Rod Assembly, Hydraulic, Left E-3.05A700 Tie Rod Assembly, Hydraulic, Right E-3.05A697 Tie Rod Assembly, Rear E-3.05P690 Tie Rod, Front E-3.05P692 Tie Rod, Hydraulic, Left E-3.05P691 Tie Rod, Hydraulic, Right E-3.05P688 Tie Rod, Rear E-3.05P465 Tire, 13", Pneumatic E-2.02P687 Tire, Pneumatic, 20/10X8BTL E-2.01
019252 Trap Door, Universal E-1.07W353 Turnbuckle End Weldment, 1" Right E-3.08W354 Turnbuckle End Weldment, 1/2" Left E-3.08M220 Turnbuckle Guard E-3.08T154 Turnbuckle Shoulder Bolt E-3.08T153 Turnbuckle, 3/4-16 E-3.08
F05011-44 Washer, Fender, 3/8” E-1.04F05011-18 Washer, Flat, #10 E-4.01F05010-18 Washer, Flat, #10 SAE E-6.07F05011-68 Washer, Flat, 1/2” E-1.03 E-2.01 E-3.08 E-5.04F05011-2 Washer, Flat, 1/2” SAE E-1.05 E-1.06 E-6.04
F05011-60 Washer, Flat, 1/4” E-1.07 E-1.08F05011-11 Washer, Flat, 1/4” SAE E-3.09 E-5.01 E-6.01F05011-72 Washer, Flat, 1/4” SAE E-7.01F05011-29 Washer, Flat, 3/4” E-7.04F05011-62 Washer, Flat, 3/4” SAE E-1.01 E-2.04 E-3.01 E-3.03 E-3.07 E-3.08F05011-3 Washer, Flat, 3/8” E-1.03 E-2.03 E-3.04 E-7.03
-
Chapter 8: Parts Manual Index Of Parts Listed By Part Description
8-17
Part No. Part Description Illustration Number(s)F05011-61 Washer, Flat, 3/8” SAE E-3.07 E-5.01 E-5.02F05011-16 Washer, Flat, 5/16” E-3.07 E-5.03F05011-17 Washer, Flat, 5/16” SAE E-4.01 E-5.01 E-7.02F05011-35 Washer, Flat, 7/16” E-6.03F05011-73 Washer, Flat, 7/8” SAE E-1.02F05011-80 Washer, Rubber, 1/2” E-6.04
P808 Washer, Shim, 1 1/8” x 1 5/8” x 1/8” E-4.01F05011-9 Washer, Split Lock, 1/2” E-2.01 E-6.04
F05011-14 Washer, Split Lock, 1/4” E-1.07 E-2.05 E-5.01F05011-6 Washer, Split Lock, 3/4” E-7.04F05011-4 Washer, Split Lock, 3/8” E-1.03 E-2.03 E-3.04 E-3.05 E-3.06 E-5.01
F05011-13 Washer, Split Lock, 5/16” E-4.01 E-5.01 E-6.04F05011-27 Washer, Split Lock, 5/8” E-1.02 E-1.03F05011-48 Washer, Split Lock, 7/16” E-4.01F05011-46 Washer, Split Lock, 7/8” E-1.02
W628 Weight Transfer Pivot Arm Wldmnt, LF E-3.07W627 Weight Transfer Pivot Arm Wldmnt, RT E-3.07W667 Weight Transfer Pivot Rod Weldment E-3.07A150 Wheel Assembly, 9” x 3.5”, UF E-2.04 E-2.05P297 Wheel Hub Assembly, DM E-2.05P291 Wheel Hub/Bearing Assy, 3/4” TRB, DM E-2.05T104 Wheel Spacer, 1/4” E-2.04T107 Wheel Spacer, 1” E-2.04A640 Wheel Yoke Assembly, 13", Left E-2.02A639 Wheel Yoke Assembly, 13", Right E-2.02A617 Wheel Yoke Assembly, Fixed Rear, Left E-2.04A618 Wheel Yoke Assembly, Fixed Rear, Right E-2.04A619 Wheel Yoke Assembly, Left E-2.04A620 Wheel Yoke Assembly, Right E-2.04W635 Wheel Yoke Weldment, 13", Left E-2.02W636 Wheel Yoke Weldment, 13", Right E-2.02W614 Wheel Yoke Weldment, Fixed Rear, LF E-2.04W615 Wheel Yoke Weldment, Fixed Rear, RTt E-2.04W665 Wheel Yoke Weldment, Left E-2.04W664 Wheel Yoke Weldment, Right E-2.04A149 Wheel/Rim Assembly, 9” x 3.5”, UF E-2.05P290 Wheel/Rim Assembly, DM E-2.05P686 Yoke, 3/8-24 E-3.05
Go to www.lastec.com for latest changes in this manual.
-
Chapter 8: Parts Manual Section 1: Decks
8-18
LasTec Articulator Model 325EParts & Illustrations
Section 1: Decks
-
Chapter 8: Parts Manual Section 1: Decks
8-19
Figure E-1.01: Deck Pivot AssemblyRef. No. Part No. Part Description
1 F05009-81 Bolt, 3/4 -10 x 2 1/8”2 P403 Bushing, bronze, 3/4” ID x 5/8”3 F05011-62 Washer, Flat, 3/4” SAE4 F05010-122 Nut, Half Nylock, 3/4-10
-
Chapter 8: Parts Manual Section 1: Decks
8-20Figure E-1.01: Deck Pivot Assembly
1
4
3
2 1
2
3
4
1
2
3
4
1
2
3
4
Deck E2
Deck E1
Deck E3
-
Chapter 8: Parts Manual Section 1: Decks
8-21
Figure E-1.02: Deck E1 & E3 Spindle AssemblyRef. No. Part No. Part Description
1 T156 Pulley, Double, XS/ES2 P103 Bearing, Spindle, Top 3 P104 Bearing, Spindle, Bottom 4 P105 O-Ring, 2 1/2” ID x 2 3/4” OD5 T157 Spindle, Keyed, XS/ES6 P407 Key, 3/16” SQ x 5/8”7 P701 Blade, 25”, High-Lift8 T180 Spindle Spacer, 1”9 F05009-80 Bolt, 5/8-18 x 2 1/4”10 F05011-27 Washer, Split Lock, 5/8”11 F05011-73 Washer, Flat, 7/8” SAE12 F05011-46 Washer, Split Lock, 7/8”13 F05010-139 Nut, Hex, 7/8-1414 P108 Grease Zerk, 1/8” NPT, Straight
-
Chapter 8: Parts Manual Section 1: Decks
8-22Figure E-1.02: Deck E1 & E3 Spindle Assembly
14
12
13
2
11
1
3
4
4
5
6
8
7
10
9
Section View Of Deck
-
Chapter 8: Parts Manual Section 1: Decks
8-23
Figure E-1.03: Deck E1 & E3 Spindle AssemblyRef. No. Part No. Part Description
1 T156 Pulley, Double, XS/ES2 P685 Pulley, Drive, 8” Deep Groove3 P103 Bearing, Spindle, Top4 P104 Bearing, Spindle, Bottom5 P105 O-Ring, 2 1/2” ID x 2 3/4” OD6 T212 Spindle, E2, Keyed7 P407 Key, 3/16” SQ x 5/8”8 P723 Key, 3/16” SQ x 1 1/2”9 P701 Blade, 25”, High-Lift10 T180 Spindle Spacer, 1”11 F05009-80 Bolt, 5/8-18 x 2 1/4”12 F05011-27 Washer, Split Lock, 5/8”13 F05007-143 Bolt, 3/8-24 x 1 1/2”14 F05011-4 Washer, Split Lock, 3/8”15 F05011-3 Washer, Flat, 3/8”16 F05011-68 Washer, Flat, 1/2”17 P108 Grease Zerk, 1/8” NPT, Straight
-
Chapter 8: Parts Manual Section 1: Decks
8-24Figure E-1.03: Deck E2 Spindle Assembly
13
1514
16
2
1
8
3
5
5
4
7
9
10
6
12
11
17Section View Of Deck
-
Chapter 8: Parts Manual Section 1: Decks
8-25
Figure E-1.04: Deck Belts & CoversRef. No. Part No. Part Description
1 P707 Belt, Insta-Power, 858702 P706 Belt, Insta-Power, 858903 W671 Pulley Cover Weldment, E13 W672 Pulley Cover Weldment, E34 F05010-24 Nut, Wing, 3/8-165 F05011-3 Washer, Fender, 3/8”
-
Chapter 8: Parts Manual Section 1: Decks
8-26
Figure E-1.04: Deck Belts & Covers
4
3
5
6
1
2
5
6
Deck E1
Deck E2
Deck E3
-
Chapter 8: Parts Manual Section 1: Decks
8-27
Figure E-1.05: Deck E1 Belt Idler AssemblyRef. No. Part No. Part Description
1 W631 Idler Arm Weldment, Low2 P403 Bushing, bronze, 3/4” ID x 5/8”3 F05010-122 Nut, Half Nylock, 3/4-104 P608 Idler Pulley, Flat5 P609 Idler Pulley, V-Groove6 F05008-10 Bolt, 1/2-13 x 2 1/4”, G87 F05011-2 Washer, Flat, 1/2” SAE8 F05010-8 Nut, Nylock, 1/2-139 019303 Spring, Extension, 1” x 7”10 P123 Grease Zerk, 1/4-28, 90°
-
Chapter 8: Parts Manual Section 1: Decks
8-28Figure E-1.05: Deck E1 Belt Idler Assembly
Deck E1
6
7
6
3
4
298
10
2
5
7
8
1
-
Chapter 8: Parts Manual Section 1: Decks
8-29
Figure E-1.06: Deck E3 Belt Idler AssemblyRef. No. Part No. Part Description
1 W632 Idler Arm Weldment, High2 P403 Bushing, bronze, 3/4” ID x 5/8”3 F05010-122 Nut, Half Nylock, 3/4-104 P608 Idler Pulley, Flat5 P609 Idler Pulley, V-Groove6 F05008-10 Bolt, 1/2-13 x 2 1/4”, G87 F05009-76 Washer, Flat, 1/2” SAE8 F05010-8 Nut, Nylock, 1/2-139 019303 Spring, Extension, 1” x 7”10 P123 Grease Zerk, 1/4-28, 90°
-
Chapter 8: Parts Manual Section 1: Decks
8-30Figure E-1.06: Deck E3 Belt Idler Assembly
Deck E3
7
3
5
2
9
8
10
2
4
7
1
6
7
8
8
-
Chapter 8: Parts Manual Section 1: Decks
8-31
Figure E-1.07: Trap Door AssembliesRef. No. Part No. Part Description
1 019252 Trap Door, Universal2 P699 Rubber Deck Seal3 C602 Rubber Clamp Strip4 F05005-101 Bolt, 1/4-20 x 1”5 F05011-14 Washer, Split Lock, 1/4”6 F05011-60 Washer, Flat, 1/4”7 M225 Pivot Guard, E18 M226 Pivot Guard, E3
-
Chapter 8: Parts Manual Section 1: Decks
8-32Figure E-1.07: Trap Door Assemblies
Deck E1
7
4
8
Deck E2
5
6
4
5
6
1
23
1 2
3
-
Chapter 8: Parts Manual Section 1: Decks
8-32
Figure E-1.08: Grass Chute & Mulching Plate AssembliesRef. No. Part No. Part Description
1 M230 Grass Chute2 F05005-101 Bolt, 1/4-20 x 1”3 F05011-60 Washer, Flat, 1/4”4 F05010-69 Nut, Nylock, 1/4-205 W633 Grass Chute Mount Weldment6 P436 Bushing, bronze, 3/8" x 1"7 P460 Spring, Torsion, 180°, LH8 F05012-1 Cotter Pin, 1/8” x 1”9 W691 Mulching Plate Weldment10 P05059 Hitch Pin, #21611 019241 Grass Chute Mount Plate, Bottom
-
Chapter 8: Parts Manual Section 1: Decks
8-34Figure E-1.08: Grass Chute & Mulching Plate Assemblies
1
8
3
2
3
4 8
7
64
6
5
10
10
9
11
-
This Page
Has Been
Intentionally
Left Blank
1 LASTEC
-
Chapter 8: Parts Manual Section 2: Wheels
8-36
LasTec Articulator Model 325EParts & Illustrations
Section 2: Wheels
-
Chapter 8: Parts Manual Section 2: Wheels
8-37
Figure E-2.01: 20” Drive Tire AssemblyRef. No. Part No. Part Description
1 P687 Tire, Pneumatic, 20/10X8BTL2 P708 Spacer Hub3 F05011-68 Washer, Flat, 1/2”4 F05011-9 Washer, Split Lock, 1/2”5 P194 Nut, Lug, 1/2-20 x 13/16” Tapered
-
Chapter 8: Parts Manual Section 2: Wheels
8-38Figure E-2.01: 20” Drive Tire Assembly
5
1
3
54
2
3
-
Chapter 8: Parts Manual Section 2: Wheels
8-39
Figure E-2.02: 13” Wheel Yoke AssembliesRef. No. Part No. Part Description
1 A639 Wheel Yoke Assembly, 13", Right2 A640 Wheel Yoke Assembly, 13", Left3 W636 Wheel Yoke Weldment, 13", Right4 W635 Wheel Yoke Weldment, 13", Left5 P465 Tire, 13", Pneumatic6 P190 Bearing, 1” Tapered Roller7 P289 Bearing Race Insert8 P191 Bearing Seal9 P433 Bearing Washer, 3/4”10 P434 Nut, Castle, 3/4-1611 P195 Hub Cap12 P447 Cotter Pin, 1/8” x 1 1/2”13 P109 Bushing, bronze, 1" ID x 1 1/4"14 P113 Lynch Pin, 1/4"15 P107 Grease Zerk, 1/4-28, Straight
Go to www.lastec.com for latest changes in this manual.
-
Chapter 8: Parts Manual Section 2: Wheels
8-40Figure E-2.02: 13” Wheel Yoke Assemblies
1
11
10
8
5
1314
3
912 7
66
7
2
10
13
13
6
13
11 6
8
12
4
14
7
79
5
15
15
Go to www.lastec.com for latest changes in this manual.
-
Chapter 8: Parts Manual Section 2: Wheels
8-41
Figure E-2.03: Side Leg AssembliesRef. No. Part No. Part Description
1 W610 Side Leg Weldment, E12 W611 Side Leg Weldment, E33 W666 Side Leg Pivot Pin Weldment4 P109 Bushing, bronze, 1"5 F05007-1 Bolt, 3/8-16 x 3” FT6 F05011-4 Washer, Split Lock, 3/8”7 F05011-3 Washer, Flat, 3/8”8 P114 Lynch Pin, 3/16”9 P123 Grease Zerk, 1/4-28, 90°
Go to www.lastec.com for latest changes in this manual.
-
Chapter 8: Parts Manual Section 2: Wheels
8-42
Figure E-2.03 Side Leg Assemblies
76
7
5
9 9
4 4
8
4 43
8
3
9 9
1 2
Go to www.lastec.com for latest changes in this manual.
-
Chapter 8: Parts Manual Section 2: Wheels
8-43
Figure E-2.04: 9” Wheel Yoke AssembliesRef. No. Part No. Part Description
1 A617 Wheel Yoke Assembly, Fixed Rear, Left2 A618 Wheel Yoke Assembly, Fixed Rear, Right3 A620 Wheel Yoke Assembly, Right4 A619 Wheel Yoke Assembly, Left5 W614 Wheel Yoke Weldment, Fixed Rear, Left6 W615 Wheel Yoke Weldment, Fixed Rear, Right7 W664 Wheel Yoke Weldment, Right8 W665 Wheel Yoke Weldment, Left9 A150 Wheel Assembly, 9” x 3.5”, UF10 P296 Bearing Spacer, 3/4” x 1/2”11 T126 Bearing Spacer, 3/4” x 11/16”12 F05010-122 Nut, Half Nylock, 3/4-1013 P109 Bushing, Bronze, 1" ID x 1 1/4"14 T107 Wheel Spacer, 1”15 T104 Wheel Spacer, 1/4”16 P110-M Clevis Pin, 3/8” x 1 5/16”17 P111 Kick-Out Ring, 1"18 F05013-70 Bolt, 3/4-10 x 6 1/2”19 F05011-62 Washer, Flat, 3/4” SAE20 F05010-103 Nut, Nylock, 3/4-10
Go to www.lastec.com for latest changes in this manual.
-
Chapter 8: Parts Manual Section 2: Wheels
8-44Figure E-2.04 9” Wheel Yoke Assemblies
1
214
13
1514
14
13
1716
1716
10
12
11 10
12
11
65
9 9
3 24
16
15
14213
15
14
13
161717
7
8
20
19
18 18
10 10 10
10
19
20
9 9
Go to www.lastec.com for latest changes in this manual.
-
Chapter 8: Parts Manual Section 2: Wheels
8-45
Wheels are shipped unlubricated from the factory. Insure proper lubrication, bear-ing preloading, and torque specifications are met. Use Loctite on all bolts. (SeeTechnical Bulletin SB-0149)
For item 1, it is possible to have a 5/16-18 nut. Please check the hub studs beforeordering new nuts. If the studs are 18 pitch, order nuts F05010-17 and lock wash-ers F05011-13.
REF PART # DESCRIPTION QTY.
A150 Wheel/Hub Assembly, 9” x 3.5” Foam-Filled
1 F05010-142 Nut, 5/16-24 Taper Lug 4
2 Deleted
3 A149 Wheel Assy, Rim and Tire (Includes items 4, 5, and 6) 1
4 F05010-63 Nut, 1/4-20 Free Hex 4
5 F05011-14 Washer, 1/4 Split Lock 4
6 F05005-123 Bolt, 1/4-20x3/4 HH Gr5 4
7 041684 Wheel Hub and Bearing Assembly, (Includes items 8, 9, 10 and 14) 1
8 P293 Bearing Seal, Trb, 1 1/8” ID 2
9 P292 Bearing, Tapered Roller, 3/4” ID 2
10 P297 Wheel Hub Assembly, Demountable (Includes items 11, 12, 13, and 15) 1
11 P402 Bearing Race Insert, 3/4" Trb 2
12 1
1 Not sold seperately.
Wheel Hub Assembly, Demountable 1
13 P294 Fitting, 1/4-28 45º Grease 1
14 048455 Spacer, 3/4 Wheel Bearing 1
15 F05004-112 Stud, 5/16-24x3/4 Press In Zinc 4
Go to www.lastec.com for latest changes in this manual.
-
Chapter 8: Parts Manual Section 2: Wheels
8-46Figure E-2.05 9” Wheel Assembly
Rim
Ass
embl
y A
149
Hub
Ass
embl
y 04
1684
Torq
ue L
ug N
ut
to 1
60 in
-lbs
Torq
ue H
ub N
ut
to 1
35 in
-lbs
Go to www.lastec.com for latest changes in this manual.
-
This Page
Has Been
Intentionally
Left Blank
1 LASTEC
Go to www.lastec.com for latest changes in this manual.
-
Chapter 8: Parts Manual Section 3: Controls
8-48
LasTec Articulator Model 325EParts & Illustrations
Section 3: Controls
Go to www.lastec.com for latest changes in this manual.
-
Chapter 8: Parts Manual Section 3: Controls
8-49
Figure E-3.01: Main Control Arm AssembliesRef. No. Part No. Part Description
1 A686 Control Arm Assembly, Main, Right2 A685 Control Arm Assembly, Main, Left3 W619 Control Arm Weldment, Main, Right4 W620 Control Arm Weldment, Main, Left5 P623 Handle, Tapered, Black6 F05010-35 Nut, Hex, 1/2-137 P403 Bushing, bronze, 3/4”8 P113 Lynch Pin, 1/4”9 F05011-62 Washer, Flat, 3/4” SAE
Go to www.lastec.com for latest changes in this manual.
-
Chapter 8: Parts Manual Section 3: Controls
8-50Figure E-3.01 Main Control Assemblies
1 2 1 2
5 5
6
3
88
9
7 7
9
7 7
4
6
Go to www.lastec.com for latest changes in this manual.
-
Chapter 8: Parts Manual Section 3: Controls
8-51
Figure E-3.02: Rear Control Arm AssembliesRef. No. Part No. Part Description
1 A687 Control Arm Assembly, Rear, Right2 A688 Control Arm Assembly, Rear, Left3 W669 Control Arm Weldment, Rear, Right4 W670 Control Arm Weldment, Rear, Left5 P635 Grip, Hand, Black6 P403 Bushing, bronze, 3/4"7 P113 Lynch Pin, 1/4"
Go to www.lastec.com for latest changes in this manual.
-
Chapter 8: Parts Manual Section 3: Controls
8-52
Figure E-3.02 Rear Control Assemblies
1 2
1
2
3 45 5
77
6
6
6
6
Go to www.lastec.com for latest changes in this manual.
-
Chapter 8: Parts Manual Section 3: Controls
8-53
Figure E-3.03: Foot Control Pedal AssembliesRef. No. Part No. Part Description
1 A689 Control Assembly, Foot, Right2 A690 Control Assembly, Foot, Left3 W621 Pedal Weldment, Foot, Right4 W622 Pedal Weldment, Foot, Left5 P629 Grip, Black6 P403 Bushing, bronze, 3/4"7 F05011-62 Washer, Flat, 3/4” SAE8 P111 Kick-Out Ring, 1"9 P107 Grease Zerk, 1/4-28, Straight
Go to www.lastec.com for latest changes in this manual.
-
Chapter 8: Parts Manual Section 3: Controls
8-54
Figure E-3.03 Foot Control Pedal Assemblies
3
1
2
1
2
4
9
67
86 6
9
67
8
5 5
Go to www.lastec.com for latest changes in this manual.
-
Chapter 8: Parts Manual Section 3: Controls
8-55
Figure E-3.04: Hydro Pivot Arm AssembliesRef. No. Part No. Part Description
1 A691 Hydraulic Pivot/Centering Arm Assembly, Right2 A692 Hydraulic Pivot/Centering Arm Assembly, Left3 A693 Hydraulic Centering Arm Assembly, Right4 A694 Hydraulic Centering Arm Assembly. Left5 W654 Hydraulic Centering Arm Mount Weldment, Right6 W653 Hydraulic Centering Arm Mount Weldment, Left7 W640 Hydraulic Centering Arm Weldment, Right8 W641 Hydraulic Centering Arm Weldment, Left9 P627 Spring, 9/16” x 5”10 P436 Bushing, bronze, 3/8"11 F05011-3 Washer, Flat, 3/8"12 F05010-124 Nut, Half Nylock, 3/8-1613 F05010-1 Nut, Hex, 3/8-1614 F05011-4 Washer, Split Lock, 3/8”15 A695 Hydraulic Pivot Arm Assembly, Right16 A696 Hydraulic Pivot Arm Assembly, Left17 W638 Hydraulic Pivot Arm Weldment, Right18 W637 Hydraulic Pivot Arm Weldment, Left19 F05007-78 Bolt, 3/8-16 x 1 1/2”20 P768 Bearing, Ball, 15mm x 35mm x 11mm21 F05010-10 Nut, Nylock, 3/8-1622 M218 Screw, Hydraulic Pivot Arm Locking
Go to www.lastec.com for latest changes in this manual.
-
Chapter 8: Parts Manual Section 3: Controls
8-56Figure E-3.04 Hydro Pivot Arm Assemblies
1 2
2
7
10
8
4
11
13
14
13
12
5
1110
3
13
13
14
12
19
22
15
23 11
11
199
2021
17
22
16
23 11
11
6
2021
18
1
11 11
9 9
Go to www.lastec.com for latest changes in this manual.
-
Chapter 8: Parts Manual Section 3: Controls
8-57
Figure E-3.05: Hydro Control Tie Rod AssembliesRef. No. Part No. Part Description
1 A697 Tie Rod Assembly, Rear2 A698 Tie Rod Assembly, Front3 A699 Tie Rod Assembly, Hydraulic, Left4 A700 Tie Rod Assembly, Hydraulic, Right5 P688 Tie Rod, Rear6 P690 Tie Rod, Front7 P692 Tie Rod, Hydraulic, Left8 P691 Tie Rod, Hydraulic, Right9 P686 Yoke, 3/8-2410 P650 Spring Pin, 3/8"11 F05010-123 Nut, Hex, 3/8-2412 F05011-4 Washer, Split Lock, 3/8”13 P651 Rod End, 3/8-24, Female14 P780 Rod End, 3/8-24, Female, Shielded
Go to www.lastec.com for latest changes in this manual.
-
Chapter 8: Parts Manual Section 3: Controls
8-58Figure E-3.05 Hydro Control Tie Rod Assemblies
1 2
21
3
4
Right SideControls
Left SideControls
5 6
5
7
6
8
10 10 1010
9
1111
9
11
9 911
13
1114
11
129
10
91111
1010
9
9
13
1111
13
12
11
1110
9
1112
11
Go to www.lastec.com for latest changes in this manual.
-
Chapter 8: Parts Manual Section 3: Controls
8-59
Figure E-3.06: Throttle & Choke Control Rod AssembliesRef. No. Part No. Part Description
1 A702 Control Rod Assembly, Throttle2 A703 Control Rod Assembly, Choke3 W629 Control Rod Weldment, Throttle/Choke4 W625 Throttle Mount Weldment, Rear5 W623 Throttle/Choke Mount Weldment, Front6 W626 Choke Mount Weldment, Rear7 P623 Handle, Tapered, Black8 F05010-72 Nut, Hex, 1/2-209 P634 Bushing, Plastic, 1/2” Split10 F05010-1 Nut, Hex, 3/8-1611 F05011-4 Washer, Split Lock, 3/8”12 F05010-69 Nut, Nylock, 1/4-2013 F05004-35 Screw, Button Head, 10-24 x 1/2”14 P641 Cable Clamp15 A701 Throttle/Choke Cable Assembly, 26”
Go to www.lastec.com for latest changes in this manual.
-
Chapter 8: Parts Manual Section 3: Controls
8-60Figure E-3.06 Throttle & Choke Control Rod Assemblies
1
2
15
3
4
11
5
9
87
12
134
1410
9
8
7
15
8
7
13
6
914
12
78 59
11
10
3
Go to www.lastec.com for latest changes in this manual.
-
Chapter 8: Parts Manual Section 3: Controls
8-61
Figure E-3.07: Deck Lift Handle AssembliesRef. No. Part No. Part Description
1 A704 Deck Lift Handle Assembly, Left2 A705 Deck Left Handle Assembly, Right3 P622 Deck Lift Handle4 W628 Weight Transfer Pivot Arm Weldment, Left5 W667 Weight Transfer Pivot Rod Weldment6 M215 Deck Lift Link Arm7 T215 Spacer, 3/8” ID x 3/4”8 F05011-3 Washer, Flat, 3/8” SAE9 F05007-47 Bolt, 3/8-16 x 2 1/2”10 F05007-78 Bolt, 3/8-16 x 1 1/2”11 P123 Grease Zerk, 1/4-28, 90°12 F05007-78 Bolt, 3/8-16 x 1 1/2”13 F05010-10 Nut, Nylock, 3/8-1614 F05010-124 Nut, Half Nylock, 3/8-1615 P403 Bushing, Bronze, 3/4”16 F05011-62 Washer, Flat, 3/4” SAE17 F05012-23 Cotter Pin, 3/16” x 2 1/2”18 F05009-62 Bolt, 5/16-18 x 1 1/4”19 F05011-16 Washer, Flat, 5/16”20 F05010-58 Nut, Nylock, 5/16-1821 C791 Chain, Deck Lift, Right, 7 1/2"22 P709 Clevis Pin, 5/16” x 1 1/2”23 P111 Kick-Out Ring, 1"24 W627 Weight Transfer Pivot Arm Weldment, Right25 C873 Chain, Deck Lift, Left, 5 3/4"26 C871 Chain Mount Extension Plate
Go to www.lastec.com for latest changes in this manual.
-
Chapter 8: Parts Manual Section 3: Controls
8-62Figure E-3.07 Deck Lift Handle Assemblies
21
6
8
33
19
23
13
18
8
16
14
10
9
6
78
13
8 8
10 12
8
158
11
13
15
17
5
22
19
18
20
19
4
4
24
10
24
10
10
88
13
88
13
145
11
5
17
1515 16
12
8 8
8
13
18
192019
2122
1923
19
25
19
8
26
Go to www.lastec.com for latest changes in this manual.
-
Chapter 8: Parts Manual Section 3: Controls
8-63
Figure E-3.08: Deck Lift Foot Pedal AssembliesRef. No. Part No. Part Description
1 W634 Deck Lift Foot Pedal Weldment2 P629 Grip, Black3 P183 Clevis Pin, 1” x 4 1/2”4 P109 Bushing, Bronze, 1" ID x 1 1/4"5 P113 Lynch Pin, 1/4"6 P151 Snapper Pin, 3/8” x 2 3/4”7 T153 Turnbuckle, 3/4-168 W353 Turnbuckle End Weldment, 1" Right9 W354 Turnbuckle End Weldment, 1/2" Left10 T154 Turnbuckle Shoulder Bolt11 F05011-2 Washer, Flat, 1/2” SAE12 F05010-8 Nut, Nylock, 1/2-1313 F05013-71 Bolt, 3/4-10 x 2”14 F05011-62 Washer, Flat, 3/4” SAE15 F05010-122 Nut, Half Nylock, 3/4-1016 M220 Turnbuckle Guard17 P107 Grease Zerk, 1/4-28, Straight
Go to www.lastec.com for latest changes in this manual.
-
Chapter 8: Parts Manual Section 3: Controls
8-64Figure E-3.08 Deck Lift Foot Pedal Assembly
12
5
3
4 4
2
6
17
1
16
15
9
11
14
13
12
7 8
10
Go to www.lastec.com for latest changes in this manual.
-
Chapter 8: Parts Manual Section 3: Controls
8-65
Figure E-3.09: Emergency Brake Handle AssemblyRef. No. Part No. Part Description
1 W649 Emergency Brake Handle Weldment2 F05010-124 Nut, Half Nylock, 3/8-163 F05010-69 Nut, Nylock, 1/4-204 F05011-11 Washer, Flat, 1/4” SAE5 P629 Grip, Black6 W659 Emergency Brake Pivot Rod Weldment7 P634 Bushing, Plastic, 1/2” Split8 F05012-1 Cotter Pin, 1/8” x 1”9 C768 Emergency Brake Tie Rod10 F05005-101 Bolt, 1/4-20 x 1”11 019520 Emergency Brake Front Tie Strap
Go to www.lastec.com for latest changes in this manual.
-
Chapter 8: Parts Manual Section 3: Controls
8-66Figure E-3.09 Emergency Brake Handle Assembly
1
22
99
6
8 8
8
87
7
10
4
8
3
4 8
3
4 4
3
5
11
Go to www.lastec.com for latest changes in this manual.
-
This Page
Has Been
Intentionally
Left Blank
1 LASTEC
Go to www.lastec.com for latest changes in this manual.
-
Chapter 8: Parts Manual Section 4: Engine/Fuel System
8-68
LasTec Articulator Model 325EParts & Illustrations
Section 4: Engine/Fuel System
Go to www.lastec.com for latest changes in this manual.
-
Chapter 8: Parts Manual Section 4: Engine/Fuel System
8-69
Figure E-4.01: Engine AssemblyRef. No. Part No. Part Description
1 P736 Kohler Engine, 25HP2 P809 Dip Stick3 P810 O-Ring4 P638 Oil Filter5 P811 Fan Guard6 F05012-1 Bolt, Allen Head, 10-32 x 5/8”7 F05004-135 Washer, Flat, #108 P774 Air Filter9 P812 Air Filter Sleeve10 P813 Air Filter Retainer Cap11 P814 Air Filter Nut, 6mm x 1.012 P815 Air Filter Cover13 P816 Muffler14 P817 Muffler Guard15 F05004-141 Screw, Shield17 F05004-134 Bolt, 6mm x 1.0 x 22mm18 F05010-144 Nut, Flanged, 6mm x 1.2519 P603 Pulley, 7”20 P724 Key, 1/4” SQ x 1”21 P604 Clutch, electric22 P808 Washer, Shim, 1 1/8” x 1 5/8” x 1/8”23 F05007-122 Bolt, 7/16-20 x 2 1/4”24 F05011-48 Washer, Split Lock, 7/16”25 P607 Belt, Insta-Power 85103026 F05006-89 (*1) Bolt, Button Head, 5/16-18 x 1 1/2”27 F05011-17 Washer, Flat, 5/16” SAE28 F05011-13 Washer, Split Lock, 5/16”29 F05010-17 Nut, Hex, 5/16-1830 P818 Cable Clamp31 F05004-135 Bolt, HHW, 10-32 x 5/8”32 P775 Spark Plug, Champion 12-132-0233 P833 Gasket, Exhaust34 P107 Fitting 1/4 -28 Straight Grease35 P403 Bushing Bronze ¾” ID x 5/8” Lg.36 F05010-122 Nut 3/4 -10 Half Nyloc37 P410 Spring 1” x 7”38 F05011-68 Washer 1/2” Standard Flat39 F05010-8 Nut ½” - 13 Nylon Hex Lock40 P608 Pulley Idler Flat41 P609 Pulley Idler V42 W630 Idler Arm Weldment43 F05008-10 Bolt 1/2” - 13 x 2 1/4”
Notes(*1) The longer engine mount bolt which is utilized as an electrical ground is an
F05008-90 5/16-18 x 2” Button Head Bolt.
43Not SHownNot shown 057525 Starter, Kohler 28 HP
Go to www.lastec.com for latest changes in this manual.
-
Chapter 8: Parts Manual Section 4: Engine/Fuel System
8-70
Figure E-4.01 Engine Assembly
1
11
9
8
7 5
6
2
31
30
4
29
28
27
26
20
22
21
19
25
23
24
17
13
14
3
10
32
33
18
15
15
3435
4243
38
39
36
4041
37
12
Go to www.lastec.com for latest changes in this manual.
-
Chapter 8: Parts Manual Section 4: Engine/Fuel System
8-71
Figure E-4.02: Fuel Tank AssemblyRef. No. Part No. Part Description
1 P605 Fuel Tank, 5 Gallon2 P820 Gas Cap3 P821 Fuel Valve, 3/8” x 1/4”4 P773 Bushing, Rubber, 3/8” Flanged5 P649 Hose Clamp, 7/16” - 5/8”
Go to www.lastec.com for latest changes in this manual.
-
Chapter 8: Parts Manual Section 4: Engine/Fuel System
8-72
Figure E-4.02 Fuel Tank Assembly
1
3
4
2
5
Go to www.lastec.com for latest changes in this manual.
-
Chapter 8: Parts Manual Section 4: Engine/Fuel System
8-73
Figure E-4.03: Fuel Line AssemblyRef. No. Part No. Part Description
1 P805 Fuel Tank, 5 Gallon2 P703 T-Fitting, 1/4”3 P822 Fuel Filter4 C678 Fuel Line, 1/4” x 30”5 C771 Fuel Line, 1/4” x 18”6 C613 Fuel Line, 1/4” x 12”7 C614 Fuel Line, 1/4” x 3 1/2”8 P649 Hose Clamp, 7/16” x 5/8”
Go to www.lastec.com for latest changes in this manual.
-
Chapter 8: Parts Manual Section 4: Engine/Fuel System
8-74
Figure E-4.03 Fuel Line Assembly
1 1
4 5
6
3
8
7
8
8
8
8 82
88
Go to www.lastec.com for latest changes in this manual.
-
This Page
Has Been
Intentionally
Left Blank
1 LASTEC
Go to www.lastec.com for latest changes in this manual.
-
Chapter 8: Parts Manual Section 5: Hydraulic System
8-76
LasTec Articulator Model 325EParts & Illustrations
Section 5: Hydraulic System
Go to www.lastec.com for latest changes in this manual.
-
Go to www.lastec.com for latest changes in this manual.
-
Go to www.lastec.com for latest changes in this manual.
-
Go to www.lastec.com for latest changes in this manual.
-
Go to www.lastec.com for latest changes in this manual.
-
Go to www.lastec.com for latest changes in this manual.
-
Go to www.lastec.com for latest changes in this manual.
-
Go to www.lastec.com for latest changes in this manual.
-
Chapter 8: Parts Manual Section 5: Hydraulic System
8-77
Figure E-5.01: Hydrostatic Drive AssembliesRef. No. Part No. Part Description
1 P615 Axle, ZT, Left2 P614 Hydrostatic Transmission Unit, Left3 P616 Axle, ZT, Right4 P613 Hydrostatic Transmission Unit, Right5 P648 Hydraulic Fitting, 3/8” HB x 7/8-14 ORB6 P645 Hydraulic Fitting, 90°, 3/8” HB x 7/16-207 P610 Pulley, 7” x 15mm8 F05006-40 Screw, Set, 5/16-18 x 3/8”9 P725 Key, 5MM SQ x 3/4”10 F05005-116 Bolt, 1/4-20 x 1 1/4”11 M221 Fan Spacer12 P606 Hydraulic Cooling Fan13 F05011-14 Washer, Split Lock, 1/4”14 F05011-11 Washer, Flat, 1/4” SAE15 F05006-78 Bolt, 5/16-18 x 7 1/4”16 P766 Hydraulic Pump Mount Spacer,17 F05011-17 Washer, Flat, 5/16” SAE18 F05010-58 Nut, Nylock, 5/16-1819 P771 O-Ring20 P767 Bearing Spacer21 P768 Bearing, Ball, 15mm x 35mm x 11mm22 P770 Input Gear23 P769 Retainer Ring24 F05006-79 Bolt, 5/16-18 x 2”25 F05011-13 Washer, Split Lock, 5/16”26 F05007-126 Bolt, 3/8-16 x 4”27 F05011-3 Washer, Flat, 3/8” SAE28 F05011-4 Washer, Split Lock, 3/8”29 F05010-1 Nut, Hex, 3/8-16
Go to www.lastec.com for latest changes in this manual.
-
Chapter 8: Parts Manual Section 5: Hydraulic System
8-78Figure E-5.01 Hydrostatic Drive Assemblies
1
227
2829
26
17
18
27
16
23 2425
21
22
20
175
15
8
9
7
10
13
6
1114
12
26
19
27
29
HydroMountPlate
HydroMountPlate
3
4
2827
23
21
22
20 16
6
17
18
5
24 25
17
15
10
13
14
10
11
7 89 19
17
17
Go to www.lastec.com for latest changes in this manual.
-
Chapter 8: Parts Manual Section 5: Hydraulic System
8-79
Figure E-5.02: Hydraulic Tank & Filter AssembliesRef. No. Part No. Part Description
1 P631 Hydraulic Oil Tank, 2 Quart2 P747 Hydraulic Oil Tank Cap3 F05007-87 Bolt, 3/8-16 x 1”4 F05011-3 Washer, Flat, 3/8” SAE5 F05010-10 Nut, Nylock, 3/8-166 P620 Oil Filter7 P619 Oil Filter Manifold8 F05011-14 Washer, Split Lock, 1/4”9 F05005-129 Bolt, 1/4-20 x 3/4”
Go to www.lastec.com for latest changes in this manual.
-
Chapter 8: Parts Manual Section 5: Hydraulic System
8-80Figure E-5.02 Hydraulic Tank & Filter Assemblies
2543
1
6
7
9
8
4
TankMountPlate
FilterMountPlate
Go to www.lastec.com for latest changes in this manual.
-
Chapter 8: Parts Manual Section 5: Hydraulic System
8-81
Figure E-5.03: Hydraulic Line AssembliesRef. No. Part No. Part Description
1 M205 Oil Cooler Cover2 P621 Oil Cooler3 W663 Oil Cooler Mount Weldment4 P631 Hydraulic Oil Tank, 2 Quart5 P620 Oil Filter6 P619 Oil Filter Manifold7 P646 Hydraulic Fitting, 90°, 3/8”8 P624 Hose Clamp9 C676 Hydraulic Hose, 3/8” x 30”10 C689 Hydraulic Hose, 3/8” x 26”11 C646 Hydraulic Hose, 3/8” x 12”12 019245 Hydraulic Hose, 3/8” x 9”13 F05006-80 Bolt, 5/16-18 x 2 1/2”14 F05011-16 Washer, Flat, 5/16”15 F05010-58 Nut, Nylock, 5/16-1816 F05006-76 Bolt, 5/16-18 x 1 1/2”
Go to www.lastec.com for latest changes in this manual.
-
Chapter 8: Parts Manual Section 5: Hydraulic System
8-82Figure E-5.02 Hydraulic Line Assemblies
1
727
8
97
8
9
10
4
83
4
11 11
8
1515
16 16 8
8
8
712128
7
778 8
7
8
13 14 1314
15 15
556 6
Rear Controls
8
10
Go to www.lastec.com for latest changes in this manual.
-
Chapter 8: Parts Manual Section 5: Hydraulic System
8-83
Figure E-5.04: Hydrostatic Mule Drive Belt Idler AssemblyRef. No. Part No. Part Description
1 W684 Idler Arm Weldment, Mule Drive2 P601 Idler Pulley, 7"3 P464 Spring, Extension, 1 1/8” x 7 1/2”4 P706 Belt, Insta-Power 858905 P403 Bushing, bronze, 3/4” ID x 5/8”6 F05011-68 Washer, Flat, 1/2”7 F05010-127 Nut, Half Nylock, 1/2-138 M235 Delrin Pad, 1 3/4” x 2”9 F05005-79 Bolt, 1/4-20 x 1/2”10 P113 Lynch Pin, 1/4"11 P107 Grease Zerk, 1/4-28, Straight
Go to www.lastec.com for latest changes in this manual.
-
Chapter 8: Parts Manual Section 5: Hydraulic System
8-84Figure E-5.04: Hydrostatic Mule Drive Belt Idler Assembly
1
2
6
6
7
9
8
10
5
5
11
3
4
Go to www.lastec.com for latest changes in this manual.
-
Chapter 8: Parts Manual Section 6: Electrical System
8-86
LasTec Articulator Model 325EParts & Illustrations
Section 6: Electrical System
Go to www.lastec.com for latest changes in this manual.
-
Chapter 8: Parts Manual Section 6: Electrical System
8-87
Figure E-6.01: Main Control Panel AssemblyRef. No. Part No. Part Description
1 W662 Control Panel Weldment, Main2 F05005-129 Bolt, 1/4-20 x 3/4”3 F05011-11 Washer, Flat, 1/4” SAE4 P602 Switch, Ignition (Replacement Keys, 028507 5 P684 Meter6 P654 Switch, OFF/Momentary ON7 P656 Switch, ON/OFF8 P683 Light, Warning
Go to www.lastec.com for latest changes in this manual.
-
Chapter 8: Parts Manual Section 6: Electrical System
8-88Figure E-6.01: Main Control Panel Assembly
6
2
7
7
5
4
2
3 3
8
2
3
1
Go to www.lastec.com for latest changes in this manual.
-
Chapter 8: Parts Manual Section 6: Electrical System
8-89
Figure E-6.02: Rear Control Panel AssemblyRef. No. Part No. Part Description
1 P656 Switch, ON/OFF2 P652 Switch, Momentary ON/Momentary OFF
Go to www.lastec.com for latest changes in this manual.
-
Chapter 8: Parts Manual Section 6: Electrical System
8-90
O N S t a r t
R u n
Figure E-6.02: Rear Control Panel Assembly
1 2
Go to www.lastec.com for latest changes in this manual.
-
Chapter 8: Parts Manual Section 6: Electrical System
8-91
Figure E-6.03: Operator Present Switch Bar AssemblyRef. No. Part No. Part Description
1 P705 Operator Present Switch Bar2 019236 Operator Present Switch Block3 F05005-47 Screw, Set, 1/4-20 x 3/8”4 P698 Switch, Operator Present5 F05011-35 Washer, Flat, 7/16”6 N/A Nut, Mounting (Included With P698 Operator Present Switch)
Go to www.lastec.com for latest changes in this manual.
-
Chapter 8: Parts Manual Section 6: Electrical System
8-92Figure E-6.03: Operator Present Switch Bar Assembly
1
2 3
6
5
4
Rear ViewRear
Controls
Go to www.lastec.com for latest changes in this manual.
-
Chapter 8: Parts Manual Section 6: Electrical System
8-93
Figure E-6.04: Light Box AssembliesRef. No. Part No. Part Description
1 W646 Light Box Weldment, Right2 W645 Light Box Weldment, Left3 P636 Headlight4 F05011-4 (*1) Washer, Split Lock, 3/8”5 F05010-123 (*1) Nut, Hex, 3/8-246 P626 Light, Flasher7 F05011-2 (*2) Washer, Flat, 1/2” SAE8 F05011-80 (*2) Washer, Rubber, 1/2”9 F05011-9 (*2) Washer, Split Lock, 1/2”10 F05010-72 (*2) Nut, Hex, 1/2-2011 F05006-5 Bolt, 5/16-18 x 3/4”12 F05011-13 Washer, Split Lock, 5/16”
Notes(*1) The F05011-4 3/8” Split Lock Washer and F05010-123 3/8-24 Hex Nut are
included in the P636 Headlight.(*2) The F05011-2 1/2” Washer, F05011-80 1/2” Rubber Washer, F05011-9 1/2”
Split Lock Washer, and F05010-72 1/2-20 Hex Nut are all included in theP626 Flasher Light.
Go to www.lastec.com for latest changes in this manual.
-
Chapter 8: Parts Manual Section 6: Electrical System
8-94Figure E-6.04: Light Box Assemblies
1 2
3
6
8
6
7
4
5
11
10
9
12
3
11
8
12
7
4
5
10
9
Front ViewRear
Controls
Go to www.lastec.com for latest changes in this manual.
-
Chapter 8: Parts Manual Section 6: Electrical System
8-95
Figure E-6.05: Neutral Start Switch AssemblyRef. No. Part No. Part Description
1 P772 Switch, Neutral Start2 L377 Neutral Start Switch Mounting Plate3 F05010-145 Nut, Jam, 9/16-184 F05006-92 Bolt, Allen Head, 5/16-18 x 1/2”5 F05010-50 Nut, Half Nylock, 5/16-18
Go to www.lastec.com for latest changes in this manual.
-
Chapter 8: Parts Manual Section 6: Electrical System
8-96Figure E-6.05: Neutral Start Switch Assembly
1
2
43
5
Section ViewOf Frame
Go to www.lastec.com for latest changes in this manual.
-
Chapter 8: Parts Manual Section 6: Electrical System
8-97
Figure E-6.06: Operator Present Switch AssemblyRef. No. Part No. Part Description
1 P826 Switch, Operator Present2 F412 Screw, Operator Present
Go to www.lastec.com for latest changes in this manual.
-
Chapter 8: Parts Manual Section 6: Electrical System
8-98Figure E-6.06: Operator Present Switch Assembly
1
2
Bottom OfSeat
Go to www.lastec.com for latest changes in this manual.
-
Chapter 8: Parts Manual Section 6: Electrical System
8-99
Figure E-6.07: Fuse Box AssemblyRef. No. Part No. Part Description
1 P662 Circuit Board2 P657 Relay3 P653 Flasher4 P666 Fuse, 10 Amp5 P665 Fuse, 3 Amp6 P828 Coupler, Hex, 10-32 x 2”7 P726 Fuse Box8 P742 Knob, Plastic, 10-32 x 3/8”9 F05004-136 Screw, SFH, 6-32 x 3/4”10 P741 Spacer11 F05010-44 Nut, Hex, 6-3212 F05004-137 Screw, SFH, 8-32 x 3/4”13 F05010-133 Nut, Hex, 8-3214 F05004-138 Screw, SFH, 10-32 x 3/8”15 F05004-139 Screw, Phillips Pan Head, 5/32” x 1/2”16 F05010-18 Washer, Flat, #10 SAE17 P682 Grommet, 5/8"
Go to www.lastec.com for latest changes in this manual.
-
Chapter 8: Parts Manual Section 6: Electrical System
8-100Figure E-6.07: Fuse Box Assembly
Fuse BoxMount Plate
1
22
3
6
8
7
9 9
10 10
11 11
13
14 12
17
Red
Yellow
Lt Green
Dk Green
Dk Brown
Purple
Orange
Lt Brown
Purple/Blacke
Lt Blue
Pink
Black(Ground)
Pink
15
1316
2
3
54
7
Go to www.lastec.com for latest changes in this manual.
-
Chapter 8: Parts Manual Section 6: Electrical System
8-101
Figure E-6.08: Battery AssemblyRef. No. Part No. Part Description
1 P625 Battery, 12V2 F05006-86 Bolt, Carriage, 5/16-18 x 3/4”3 F05010-17 Nut, Hex, 5/16-184 P743 Cable, Battery, 42”, Black5 P677 Cable, Battery, 52”, Red6 P632 Battery Terminal Cover, Red
Go to www.lastec.com for latest changes in this manual.
-
Chapter 8: Parts Manual Section 6: Electrical System
8-102
Figure E-6.08: Battery Assembly
1
4
3
25
2
3
6
Go to www.lastec.com for latest changes in this manual.
-
This Page
Has Been
Intentionally
Left Blank
1 LASTEC
Go to www.lastec.com for latest changes in this manual.
-
Chapter 8: Parts Manual Section 7: General
8-104
LasTec Articulator Model 325EParts & Illustrations
Section 7: General
Go to www.lastec.com for latest changes in this manual.
-
Chapter 8: Parts Manual Section 7: General
8-105
Figure E-7.01: Fender AssembliesRef. No. Part No. Part Description
1 M210 Fender, Outer2 W661 Fender, Inside, Right3 W660 Fender, Inside, Left4 P611 Cup Holder5 F05006-5 Bolt, Wing, 5/16-18 x 3/4”6 F05011-72 Washer, Flat, 1/4” SAE7 F05005-129 Bolt, 1/4-20 x 3/4”
Go to www.lastec.com for latest changes in this manual.
-
Chapter 8: Parts Manual Section 7: General
8-106Figure E-7.01: Fender Assemblies
1 1
2
4
3
4
5 5
6
7
6
7
Go to www.lastec.com for latest changes in this manual.
-
Chapter 8: Parts Manual Section 7: General
8-107
Figure E-7.02: Seat & Seat Pan AssemblyRef. No. Part No. Part Description
1 P630 Seat2 L316 Seat Spacer Plate3 W647 Seat Pan Weldment4 P748 (*1) Seat Slide Track5 F05006-1 Bolt, 5/16-18 x 1”6 F05011-17 Washer, Flat, 5/16” SAE7 F05010-58 Nut, Nylock, 5/16-188 F05010-17 Nut, Hex, 5/16-189 F05011-13 Washer, Split Lock, 5/16
Notes(*1) The P748 Seat Slide Tracks are included in the P630 Seat Assembly.
Go to www.lastec.com for latest changes in this manual.
-
Chapter 8: Parts Manual Section 7: General
8-108Figure E-7.02: Seat & Seat Pan Assembly
1
3
24
7
67
7
6
8
65
6
9 98 8
5
5
6
Go to www.lastec.com for latest changes in this manual.
-
Chapter 8: Parts Manual Section 7: General
8-109
Figure E-7.03: Seat & Seat Pan AssemblyRef. No. Part No. Part Description
1 W647 Seat Pan Weldment2 019538 Kick Stand Strap, Long3 W678 Kick Stand Weldment, Short4 F05007-147 Bolt, 3/8-16 x 3/4”5 F05011-3 Washer, Flat, 3/8”6 F05010-124 Nut, Half Nylock, 3/8-167 F05010-10 Nylock, 3/8-16
Go to www.lastec.com for latest changes in this manual.
-
Chapter 8: Parts Manual Section 7: General
8-110Figure E-7.03: Seat Pan & Kick Stand Assembly
1
4
3
2
4
6
46
5
5
5
55
5
77
6
Bottom ViewOf Seat Pan
Section ViewOf Frame
Go to www.lastec.com for latest changes in this manual.
-
Chapter 8: Parts Manual Section 7: General
8-111
Figure E-7.04: Front Axle & Pull Bar AssemblyRef. No. Part No. Part Description
1 W613 Axle Weldment, Front2 W612 Pull Bar Weldment3 W648 Pull Pin Weldment4 P184 Clevis Pin, 1” x 5 1/4”5 P612 Bushing, bronze, 1 1/2” ID x 1 1/2”6 F05013-72 Bolt, 3/4-16 x 1 1/2”7 F05011-6 Washer, Split Lock, 3/4”8 F05011-29 Washer, Flat, 3/4”9 P109 Bushing, bronze, 1” ID x 1 1/4”10 P107 Grease Zerk, 1/4-28, Straight11 P113 Lynch Pin, 1/4"
Go to www.lastec.com for latest changes in this manual.
-
Chapter 8: Parts Manual Section 7: General
8-112Figure E-7.04: Front Axle & Pull Bar Assembly
1
239
10
11
6
44
5
5
78
9
9 9
10
10 1011
11
1010
Go to www.lastec.com for latest changes in this manual.
-
Chapter 8: Parts Manual Section 7: General
8-113
Figure E-7.05: Weight Transfer SpringsRef. No. Part No. Part Description
1 P628 Spring, Weight Transfer, 24”
Go to www.lastec.com for latest changes in this manual.
-
Chapter 8: Parts Manual Section 7: General
8-114Figure E-7.05: Weight Transfer Springs
1 1
Go to www.lastec.com for latest changes in this manual.
-
Chapter 8: Parts Manual Section 7: General
8-115
Figure E-7.06: DecalsRef. No. Part No. Part Description
1 P487 Decal, Rear Control2 P476 Decal, Warning, “Avoid Injury”, Rear3 P480 Decal, Throttle4 P479 Decal, Choke5 P481 Decal, Hydraulic Oil6 P485 Decal, Fuel7 P484 Decal, Control, Forward/Back8 P478 Decal, Warning, “Rotating Blades”9 P477 Decal, Warning, “Thrown Objects”10 P486 Decal, Main Control11 P491 Decal, Emergency Brake12 P475 Decal, Warning, “Avoid Injury”, Front13 P482 Decal, Deck Release14 P493 Decal, Warning, “Clear Area”15 P118 Decal, Die-Cut, “LasTec”16 P119 Decal, Die-Cut, “Articulator”
Go to www.lastec.com for latest changes in this manual.
-
Chapter 8: Parts Manual Section 7: General
8-116
Read operator's manual before operatingKnow function and location of all controls
Maintain all safety devicesRemove objects that could be thrown by the bladeLook down and behind before and while backing
Avoid slippery, wet, or steep areasAvoid sudden turns
If machine stops going uphill, stop blade & back down slowly
Avoid blade unless blade and engine are stoppedNever carry children
Do not mow when children or others are aroundNever remove or raise grass chute while mowing
Keep safety devices (guard s, shields, and switches) in place and working
Never bypass safety switches
The Articulator Model 325EManufactured By LasTec Inc.
7865 NCR 100E, Lizton, IN 46149Phone (317) 892-4444 Fax (317) 892-4188
FU
EL
-
G
AS
OL
IN
E
ON
LY
Tu
rn
O
ff
E
ng
in
e
Be
fo
re
R
ef
ue
li
ng
Ne
ve
r
Fi
ll
T
an
k
In
do
or
s
or
Wh
en
E
ng
in
e
is
H
ot
Wi
pe
O
ff
A
ll
S
pi
ll
ed
G
as
ol
in
e
Be
fo
re
S
ta
rt
in
g
En
gi
ne
Do
N
ot
S
mo
ke
W
he
n
Re
fu
el
in
g
FU
EL
-
G
AS
OL
IN
E
ON
LY
Tu
rn
O
ff
E
ng
in
e
Be
fo
re
R
ef
ue
li
ng
Ne
ve
r
Fi
ll
T
an
k
In
do
or
s
or
Wh
en
E
ng
in
e
is
H
ot
Wi
pe
O
ff
A
ll
S
pi
ll
ed
G
as
ol
in
e
Be
fo
re
S
ta
rt
in
g
En
gi
ne
Do
N
ot
S
mo
ke
W
he
n
Re
fu
el
in
g
Close Open
ChokeSlow Fast
Throttle
Pa
rk
in
g
Br
ak
e
BLADES OILLIGHTSBeam Hazard
ENGINE
The ArticulatorModel 325E
Sta
rt
Start
Run
Hours/Service/RPM
Operate Main Controls From Operator Seat ONLY
ONStart
Run
Figure E-7.06: Decals
1 2
8
7
6
5
3
8
9
1012
14
7
11
8
7
6
5
4
8
7
7 7
13
15
16
Go to www.lastec.com for latest changes in this manual.
-
This Page
Has Been
Intentionally
Left Blank
1 LASTEC
Go to www.lastec.com for latest changes in this manual.
Parts ManualSection 1 DecksDeck Pivot AssemblyDeck E1 and E3 Spindle AssemblyDeck E1 and E3 Spindle AssemblyDeck Belts and CoversDeck E1 Belt Idler AssemblyDeck E3 Belt Idler AssemblyTrapDoor AssembliesGrass Chute and Mulching Plate Assemblies
Section 2 Wheels20" Drive Tire Assembly13" Wheel Yoke AssembliesSide Leg Assemblies9" Wheel Yoke Assemblies9" Wheel Assembly
Section 3 ControlsMain Control Arm AssembliesRear Control Arm AssembliesFoot Control Pedal AssembliesHydro Pivot Arm AssembliesHydro Control Tie Rod AssembliesThrottle and Choke Control Rod AssembliesDeck Lift Handle AssembliesDeck Lift Foot Pedal AssembliesEmergency Brake Handle Assembly
Section 4 Engine/Fuel SystemEngine AssemblyFuel Tank AssemblyFuel Line Assembly
Section 5 Hydraulic SystemHydrostatic Drive AssembliesHydraulic Tank and Filter AssembliesHydraulic Line AssembliesHydrostatic Mule Drive Belt Idler Assembly
Section 6 Electrical SystemMain Control Panel AssemblyRear Control Panel AssemblyOperator Present Switch Bar AssemblyLight box AssembliesNeutral Start Switch AssemblyOperator Present Switch AssemblyFuse Box AssemblyBattery Assembly
Section 7 GeneralFender AssembliesSeat and Seat Pan AssemblySeat and Seat Pan AssemblyFront Axle and Pull Bar AssemblyWeight Transfer SpringsDecals