latest trend in extrusion
TRANSCRIPT
![Page 1: Latest Trend in Extrusion](https://reader034.vdocuments.net/reader034/viewer/2022052522/551f5e124979592e5b8b4c75/html5/thumbnails/1.jpg)
![Page 2: Latest Trend in Extrusion](https://reader034.vdocuments.net/reader034/viewer/2022052522/551f5e124979592e5b8b4c75/html5/thumbnails/2.jpg)
PLASTICS - INDIAN SCENARIO
Ranked 8th in the world in Plastic Consumption.
Per Capita consumption of 6 Kg compare to 27 Kg of world.
Expected to be 3rd largest consumer of plastic after US & China by 2010.
Raw Material producers - 15 Nos.
Total No. of processing unit - 30,000 approx.
Total No. of Machines - 58,811 approx.
Total No. of Extrusion Machines - 19,000 approx.
![Page 3: Latest Trend in Extrusion](https://reader034.vdocuments.net/reader034/viewer/2022052522/551f5e124979592e5b8b4c75/html5/thumbnails/3.jpg)
PLASTIC PROCESSING TECHNOLOGY
EXTRUSION – Pipes, Profiles, Films, Wire Coating etc.
INJECTION MOLDING – Crates, Furniture, Electrical Comp., etc.
BLOW MOLDING – Bottles, Cans, Containers etc.
OTHERS – Thermoforming, Compression, Rotational etc.
SHARE BY PROCESSING SEGMENT
Extrusion - 66%
Injection Molding - 20%
Blow Molding - 06%
Others - 03%
Hand Operated - 05%
![Page 4: Latest Trend in Extrusion](https://reader034.vdocuments.net/reader034/viewer/2022052522/551f5e124979592e5b8b4c75/html5/thumbnails/4.jpg)
OVERVIEW ON EXTRUSION TECHNOLOGY OF
PIPE
• PVC
• CPVC
• 3 – LAYER FOAM CORE
• HDPE
• PPR
![Page 5: Latest Trend in Extrusion](https://reader034.vdocuments.net/reader034/viewer/2022052522/551f5e124979592e5b8b4c75/html5/thumbnails/5.jpg)
![Page 6: Latest Trend in Extrusion](https://reader034.vdocuments.net/reader034/viewer/2022052522/551f5e124979592e5b8b4c75/html5/thumbnails/6.jpg)
GENERAL ARRANGEMENT OF PVC PIPE PLANTGENERAL ARRANGEMENT OF PVC PIPE PLANT
EXTRUDER
DIE HEAD
VACUUM TANKSPRAY TANKHAUL-OFFCUTTERTRIPPING
EXTRUDER
DIE HEAD
(WITH TROLLEY)
VACUUM TANK
SPRAY TANK
HAUL-OFFCUTTER
![Page 7: Latest Trend in Extrusion](https://reader034.vdocuments.net/reader034/viewer/2022052522/551f5e124979592e5b8b4c75/html5/thumbnails/7.jpg)
![Page 8: Latest Trend in Extrusion](https://reader034.vdocuments.net/reader034/viewer/2022052522/551f5e124979592e5b8b4c75/html5/thumbnails/8.jpg)
COMPARISON BETWEEN SINGLE & TWIN SCREW EXTRUDERS
SINGLE SCREW TWIN SCREW
OUTPUT LOW HIGH
POWER CONSUMPTION HIGH LOW
FORMULATION COST HIGH LOW
SHEAR RATE HIGH LOW
MIXING POOR VERY GOOD
COST LOW HIGH
ECONOMIC VIABILITY VERY POOR VERY GOOD
![Page 9: Latest Trend in Extrusion](https://reader034.vdocuments.net/reader034/viewer/2022052522/551f5e124979592e5b8b4c75/html5/thumbnails/9.jpg)
TWIN SCREW EXTRUDER MODEL
Conventional Version V Model Push Button Type
Latest Version V4 Model Smart Touch Type
![Page 10: Latest Trend in Extrusion](https://reader034.vdocuments.net/reader034/viewer/2022052522/551f5e124979592e5b8b4c75/html5/thumbnails/10.jpg)
SCREW TEMPERATURE CONTROL SYSTEM SCREW TEMPERATURE CONTROL SYSTEM
• Works on the principle of the heat exchanger tube, improving heat exchange between the various zones of the screw. • Distilled water is used as the temperature control medium.• It evaporates in the high temperature section of the screw and releases the energy absorbed by condensing in the low temperature section.• Lower energy consumption & absolutely no maintenance.
![Page 11: Latest Trend in Extrusion](https://reader034.vdocuments.net/reader034/viewer/2022052522/551f5e124979592e5b8b4c75/html5/thumbnails/11.jpg)
Vertical Feeder - allows under-filling, complete filling or forced feeding of material into the screw.a whole range of marketable formulation can be processed having different
bulk densities with just one screw geometry. enables the extruder rate to be raised even with low bulk densities.lowers the screw speed while keeping output constant and thereby reducing
wear.
VERTICAL FEEDER VS. HORIZONTAL FEEDERVERTICAL FEEDER VS. HORIZONTAL FEEDER
VERTICAL(CRAMMER) HORIZONTAL
Barrel
Free fall of PVC compound
Feeder screw Drive
![Page 12: Latest Trend in Extrusion](https://reader034.vdocuments.net/reader034/viewer/2022052522/551f5e124979592e5b8b4c75/html5/thumbnails/12.jpg)
![Page 13: Latest Trend in Extrusion](https://reader034.vdocuments.net/reader034/viewer/2022052522/551f5e124979592e5b8b4c75/html5/thumbnails/13.jpg)
SINGLE SPIDER DIE
• Ideal dwell time profile over the whole flow cross-section.
• Homogeneous melt distribution with selective temperature control.
• Facilitates high output.
SINGLE SPIDER
![Page 14: Latest Trend in Extrusion](https://reader034.vdocuments.net/reader034/viewer/2022052522/551f5e124979592e5b8b4c75/html5/thumbnails/14.jpg)
DOUBLE SPIDER DIE HEAD - RD SERIES
DOUBLE SPIDER
• Elimination of spider lines due to staggered double Decker spider.
• Improved mechanical properties.
• Processing of thick wall pipes without spider lines.
• Excellent wall thickness control at higher throughput rate.
![Page 15: Latest Trend in Extrusion](https://reader034.vdocuments.net/reader034/viewer/2022052522/551f5e124979592e5b8b4c75/html5/thumbnails/15.jpg)
ACCOUNTANCY
WIDER PIPE DIAMETER RANGE
75 / 250 : 20D – 75D
110 / 250 : 63D – 110D
200 / 400 : 63D – 200D
250 / 600 : 90D – 250D
315 / 800 : 110D – 315D
400 / 800 : 110D – 400D
450 / 1000 : 160D – 450D
RD – 1 : 20D – 110D(725 Kg/Hr.)
RD – 2 : 63D – 280D(910 Kg/Hr.)
RD – 3 : 160D – 450D(1500 Kg/Hr.)
EXISTING DIE HEAD NEW RD SERIES DIE HEAD
![Page 16: Latest Trend in Extrusion](https://reader034.vdocuments.net/reader034/viewer/2022052522/551f5e124979592e5b8b4c75/html5/thumbnails/16.jpg)
![Page 17: Latest Trend in Extrusion](https://reader034.vdocuments.net/reader034/viewer/2022052522/551f5e124979592e5b8b4c75/html5/thumbnails/17.jpg)
CALIBRATION Calibration is required to form the pipe.
Pipe outside dia is sized in sizer unit.
Two methods for sizing calibration.
(Pressure calibration & Vacuum calibration)
PRESSURE CALIBRATION (Spray Tank K Type)
Floating bunk with help of chain is to be inserted in pipe after pressure
calibration sleeve.
Compressed air is supplied through die between floating bunk & die.
Pipe is formed by internal air pressure 0.5 bar air pressure is given.
Pipe is cooled by closed water spraying thr’u nozzle at 2.5 bar.
![Page 18: Latest Trend in Extrusion](https://reader034.vdocuments.net/reader034/viewer/2022052522/551f5e124979592e5b8b4c75/html5/thumbnails/18.jpg)
Vacuum regulator system
Water Sump
Spray Pump
Vacuum Pump
Double Filter Unit
VACUUM CALIBRATION (Vacuum Tank V Type)
Pipe is welded with lead pipe is pulled by haul off & vacuum is
applied in vacuum tank to form the pipe .
Pipe is sized in vacuum calibration sleeve.
200 to 400 mm of Hg vacuum is kept .
Pipe is cooled by close water spraying thr’u nozzle at 2.5 Bar
![Page 19: Latest Trend in Extrusion](https://reader034.vdocuments.net/reader034/viewer/2022052522/551f5e124979592e5b8b4c75/html5/thumbnails/19.jpg)
![Page 20: Latest Trend in Extrusion](https://reader034.vdocuments.net/reader034/viewer/2022052522/551f5e124979592e5b8b4c75/html5/thumbnails/20.jpg)
MULTIBELT HAUL-OFF
For higher dia pipe pulling force required is more, so multibelt haul-off is recommended. It also ensures roundness of the pipe.
4 Belts 50% force required than 2 belts.
6 Belts 30% force required than 2 belts
So in multibelt haul-off dimensional control is better.
HAUL-OFF
2-BELT HAUL-OFF
![Page 21: Latest Trend in Extrusion](https://reader034.vdocuments.net/reader034/viewer/2022052522/551f5e124979592e5b8b4c75/html5/thumbnails/21.jpg)
![Page 22: Latest Trend in Extrusion](https://reader034.vdocuments.net/reader034/viewer/2022052522/551f5e124979592e5b8b4c75/html5/thumbnails/22.jpg)
Two types of cutter:-
1. SPR type cutter (upstroke),(up to 200Ø, Upgraded to new model 225Ø,250Ø)
- Extended bed cutter for smaller diameter pipes with higher line speed.
2. SU type cutter (planetary), (up to 630Ø)
- Flush mounted saw is provided for smaller OD pipes.
- Planetary saw is provided for larger OD pipes.
- Thicker as well as thinner pipes can be cut without Burrs.
- Chamfering on one or both sides is possible with adjustable chamfer size.
SU-CUTTER SPR-CUTTER
![Page 23: Latest Trend in Extrusion](https://reader034.vdocuments.net/reader034/viewer/2022052522/551f5e124979592e5b8b4c75/html5/thumbnails/23.jpg)
![Page 24: Latest Trend in Extrusion](https://reader034.vdocuments.net/reader034/viewer/2022052522/551f5e124979592e5b8b4c75/html5/thumbnails/24.jpg)
DUAL STRAND EXTRUSIONDUAL STRAND EXTRUSION
Dual stand extrusion lines are advantageous when higher throughputs are to be achieved even with Smaller & thinner pipes.
Dual strand extrusion allows almost100% utilization of extruder capacity for small & thinner Pipes, which is otherwise not possible in single lines.
Different diameters can be produced simultaneously On dual strand lines.
Dual strand line offers an impressive Price/performance ratio.
![Page 25: Latest Trend in Extrusion](https://reader034.vdocuments.net/reader034/viewer/2022052522/551f5e124979592e5b8b4c75/html5/thumbnails/25.jpg)
CPVC PIPES
![Page 26: Latest Trend in Extrusion](https://reader034.vdocuments.net/reader034/viewer/2022052522/551f5e124979592e5b8b4c75/html5/thumbnails/26.jpg)
•Ideally suited for self supporting constructions as plumbing pipes.
•Ideally suited for transporting hot & cold water in residential complex, hotels, hospitals, etc.
•Also approved for potable water.
•Used in industrial piping too.
CPVC PIPES
![Page 27: Latest Trend in Extrusion](https://reader034.vdocuments.net/reader034/viewer/2022052522/551f5e124979592e5b8b4c75/html5/thumbnails/27.jpg)
SPECIAL FEATURES OF CPVC PLANT:
•HIGHER TORQUE GEAR BOX
•HIGH CAPACITY MOTOR
•TRIPLE PLATING SCREWS
•STAINLESS STEEL CONNECTING HEAD
•STAINLESS STEEL DIE HEAD
•STAINLESS STEEL DIES
•STAINLESS STEEL VACUUM TANK
![Page 28: Latest Trend in Extrusion](https://reader034.vdocuments.net/reader034/viewer/2022052522/551f5e124979592e5b8b4c75/html5/thumbnails/28.jpg)
PRODUCTION OF PVC-U FOAM CORE PIPESPRODUCTION OF PVC-U FOAM CORE PIPES3 LAYER PIPE3 LAYER PIPE
![Page 29: Latest Trend in Extrusion](https://reader034.vdocuments.net/reader034/viewer/2022052522/551f5e124979592e5b8b4c75/html5/thumbnails/29.jpg)
APPLICATIONSAPPLICATIONS : :
At present foam core pipes are used only for non-pressure applications such as drainage sewage and ventilation pipes. In addition, they are used for cable protection.
ADVANTAGES OF 3-LAYER FOAM CORE PIPE :
Lower thermal conductivity (insulating effect). Weight/ meter reduces. Lower costs per meter length.
ADVANTAGES OF 3-LAYER COMPACT PIPES :
Saving of material costs by using recycled material in the middle layer.
Possibility to use different PVC formulations (increased pipe quality).
3-layer increase the stress specification (sandwich). 3-layer can minimize the effects of inclusions.
![Page 30: Latest Trend in Extrusion](https://reader034.vdocuments.net/reader034/viewer/2022052522/551f5e124979592e5b8b4c75/html5/thumbnails/30.jpg)
LAYER THICKNESS DISTRIBUTION
The minimum thickness of the inner and outer layer depends on the pipe size. The tolerance for overall pipe dimension correspond to the specification of the din standards.
10-25INNER
60-80MIDDLE
10-15OUTER
% OF TOTAL WALLTHICKNESS
LAYER
![Page 31: Latest Trend in Extrusion](https://reader034.vdocuments.net/reader034/viewer/2022052522/551f5e124979592e5b8b4c75/html5/thumbnails/31.jpg)
HDPE PIPES
![Page 32: Latest Trend in Extrusion](https://reader034.vdocuments.net/reader034/viewer/2022052522/551f5e124979592e5b8b4c75/html5/thumbnails/32.jpg)
ADVANTAGES OVER PVC1. Very high impact strength
2. Light weight
3. Flexibility and Ductility
4. Chemical resistance
5. Weatherability
6. Smooth internal surfaceAPPLICATIONS:• Industries 11. Power generation• Agricultural irrigation 12. Pulp and paper• Optical fiber cable conduits 13. Sewage• Chemical 14. Potable water supply• Dredging 15. Submarine pipelines• Fertilizers 16. Corrosive wastage• Domestic gas distribution 17. Drainage lines• Landfill reclamation 18. Relining salt water intakes• Mining• Oil and gas production
7. Resistance to rodent attack
8. Corrosion-Resistant
9. Inert
10.Non Toxic
11. Long Lasting
12. Terrain Following
![Page 33: Latest Trend in Extrusion](https://reader034.vdocuments.net/reader034/viewer/2022052522/551f5e124979592e5b8b4c75/html5/thumbnails/33.jpg)
Single Screw Extruder
Automatic Hopper Loader
Hopper
Heating Panel
Plug Socket For Die Head
Barrel Cooling Blower
Single Screw
Smart Touch
![Page 34: Latest Trend in Extrusion](https://reader034.vdocuments.net/reader034/viewer/2022052522/551f5e124979592e5b8b4c75/html5/thumbnails/34.jpg)
GROOVED FEED BUSH:
For the extrusion of polyolefin pipes, single screw extruders are equipped with grooved feed bush.
In combination with barrier screw, these extruder achieve high plastification rates whilst delivering and excellent melt homogeneity.
![Page 35: Latest Trend in Extrusion](https://reader034.vdocuments.net/reader034/viewer/2022052522/551f5e124979592e5b8b4c75/html5/thumbnails/35.jpg)
Main flight
Discharge zone Barrier zone Feed zone
Trailing edgeSolid bed Melt reservoir
Leading edge
Cylinder
Solid channel Barrier flight
Melt flight
PRINCIPLE OF THE BARRIER SCREW
![Page 36: Latest Trend in Extrusion](https://reader034.vdocuments.net/reader034/viewer/2022052522/551f5e124979592e5b8b4c75/html5/thumbnails/36.jpg)
• Due to separate melt & solid channels, less heat is required to get good melt quality
• Due to this, processing at lesser melt temperature is possible
• Higher throughput rates without compromise on melt quality
• Improved melt homogeneity.
• Better physical properties
• Wide range of material can be processed in same screw
• Reduced power consumption on account of less melt temperature & less motor power
ADVANTAGES OF BARRIER SCREWADVANTAGES OF BARRIER SCREW
![Page 37: Latest Trend in Extrusion](https://reader034.vdocuments.net/reader034/viewer/2022052522/551f5e124979592e5b8b4c75/html5/thumbnails/37.jpg)
LATTICE BASKET DIE HEAD (SI)
Low pressure build-up and low melt temperature, even with high throughput.
Good homogenization due to double diversion of the melt.
Constant processing characteristics over the full range of materials.
Consistent product quality for all pipe sizes.
![Page 38: Latest Trend in Extrusion](https://reader034.vdocuments.net/reader034/viewer/2022052522/551f5e124979592e5b8b4c75/html5/thumbnails/38.jpg)
Faster assembly lesser maintenance due to lesser components.
Even distribution of material.
Ideal for thin walled pipes.
SPIRAL MANDREL DIE HEAD
![Page 39: Latest Trend in Extrusion](https://reader034.vdocuments.net/reader034/viewer/2022052522/551f5e124979592e5b8b4c75/html5/thumbnails/39.jpg)
SPIRAL LATTICE BASKET DIE HEAD (VSi)
Consists of spiral for coarse distribution and a compact lattice for fine distribution of melt.Large processing window.Low pressure requirement.Excellent wall thickness distribution.
![Page 40: Latest Trend in Extrusion](https://reader034.vdocuments.net/reader034/viewer/2022052522/551f5e124979592e5b8b4c75/html5/thumbnails/40.jpg)
![Page 41: Latest Trend in Extrusion](https://reader034.vdocuments.net/reader034/viewer/2022052522/551f5e124979592e5b8b4c75/html5/thumbnails/41.jpg)
JOCKEY EXTRUDER
19mm JOCKEY EXTD.
30mm JOCKEY EXTD.
![Page 42: Latest Trend in Extrusion](https://reader034.vdocuments.net/reader034/viewer/2022052522/551f5e124979592e5b8b4c75/html5/thumbnails/42.jpg)
![Page 43: Latest Trend in Extrusion](https://reader034.vdocuments.net/reader034/viewer/2022052522/551f5e124979592e5b8b4c75/html5/thumbnails/43.jpg)
• It endures to heat and high climatic temperatures.• It reserves its original form, flexibility and chemical properties at high
temperatures.• It is resistant to chemical reactions, acids salt and alkali, may safely
be used together.• It has resistance to corrosion, it does not rust or decay.• The friction calcification is very low, the surface is clean and smooth
and it will not hold other particles to fill in cavities.• There is no isolation against heat. It is resistance to extreme heat/cold
and will not deform or give in between –20 °C to +90°C environmental temperatures.
• It is extremely light, therefore easy to transport and install.• It is resistant to ultra violet rays. (Black color type)• The operational pressure resistance is 20 ATU at 20°C and 10 ATU at
65°C.• It is resistant to long term hot water transmission and under normal
environmental condition it endures operational heat 70°C – 90°C
FEATURES:-
![Page 44: Latest Trend in Extrusion](https://reader034.vdocuments.net/reader034/viewer/2022052522/551f5e124979592e5b8b4c75/html5/thumbnails/44.jpg)