lbnl ccd packaging “yale mount” mechanical analysis dan cheng lbnl

LBNL CCD Packaging“Yale Mount” Mechanical Analysis

Dan Cheng

LBNL

4/19/2003 Dan Cheng 2

First Guess for SNAP

1.4mm thick AlN substrate with 200m via’s, not under bumps or CCD

CCD, 200m thickGold bump (flattened wire bond bump)applied in house

Underfill with Epotek301-2 glue at 60oC

Gold platedInvar

Connector mounted to Invarwith spring loaded pins against AlN

AlN circuits from COORS

Bumps on AlN appliedat 4” wafer size levelthen diced

No success yet in wafer scale bump bonds with AlN…dicing leaves large chips on edges

4/19/2003 Dan Cheng 3

Yale CCD Mount

4/19/2003 Dan Cheng 4

Solid Model Geometry (Pro/E)

Rear View

Front View

4/19/2003 Dan Cheng 5

Quarter-Symmetry Solid Model

CCD(200 microns thick) Substrate

(1.5-mm thick AlNOr 2-mm thick Si)

EA9361 Epoxy(250 microns thick)

Molybdenum Base(~5-mm thick)

EPO-TEK 301-2(50 microns thick)

4/19/2003 Dan Cheng 6

Finite Element Mesh

4/19/2003 Dan Cheng 7

FEA Notes

• Quarter-symmetry model

— Approximately 80,000 elements

• Symmetric boundary constraints

— X- and Y- symmetry planes fixed, allowed to “slide”

— Z-symmetry plane about square hole fixed in Z-direction

• Most material properties are temperature-dependent

— With the exception of some Young’s Modulus numbers

4/19/2003 Dan Cheng 8

FEA Assumptions

• Mounting holes

— Assumed constraints—see previous slide

• Did not model Gold/Indium bump bonds

4/19/2003 Dan Cheng 9

FEA Notes

• Ran four cases

— Case 1: AlN Substrate, Square hole

— Case 2: Si Substrate, Square hole

— Case 3: AlN Substrate, Square hole w/Fillets

— Case 4: Si Substrate, Square hole w/Fillets

4/19/2003 Dan Cheng 10

FEA Epo-Tek Stress Contour Plot

4/19/2003 Dan Cheng 11

FEA AlN Substrate Results

Case 1, ALN Substrate, Square Hole

Max Z Displacement 24 microns At corner edge

Max VM Stress 347 MPa

~50 ksi

Corner of square hole in Moly

CCD Max Stress 26 MPa

3.7 ksi

Max. Substrate Stress

51 MPa

7.4 ksi

EA9361 Joint 37 MPa

5.4 ksi

Closer to 18-20 Mpa average (2.7 ksi)

Epo-Tek 301-2 Joint 7.5 MPa

1.1 ksi

Bending shear*

4/19/2003 Dan Cheng 12

FEA Si Substrate Results

Case 2, ALN Substrate, Square Hole



~47 ksi



2.5 ksi


64 MPa

9.3 ksi

EA9361 Joint 36 MPa

5.4 ksi



.9 ksi

Bending shear

4/19/2003 Dan Cheng 13

FEA AlN Substrate Results #2

Case 3, ALN Substrate, Square Hole with Fillets



~43 ksi



3.5 ksi


50 MPa

7.4 ksi

EA9361 Joint 34 MPa

4.9 ksi



1 ksi

Bending shear*

4/19/2003 Dan Cheng 14

FEA Si Substrate Results #2

Case 4, ALN Substrate, Square Hole with Fillets



~40 ksi



2.2 ksi


64 MPa

9.3 ksi

EA9361 Joint 35 MPa

5.4 ksi



.9 ksi

Bending shear

4/19/2003 Dan Cheng 15

FEA Summary

• Some material properties need to be defined at operating temperature (140 K)

• Current design shows critical Epo-Tek joint at above Yield Stress of 926 psi (may change with model)