lcd projector np3200/np2200/np1200 - nec · pdf filelcd projector np3200/np2200/np1200 ......

LCD Projector

NP3200/NP2200/NP1200User’s Manual

The NP3200 is not distributed in North America.

1st edition, October 2009

• IBMisatrademarkorregisteredtrademarkofInternationalBusinessMachinesCorporation.

• Macintosh,MacOSXandPowerBookaretrademarksofAppleInc.,registeredintheU.S.andothercountries.

• Microsoft,Windows,WindowsVista, InternetExplorer, .NETFrameworkandPowerPointareeitheraregisteredtrademarkortrademarkofMicrosoftCorporationintheUnitedStatesand/orothercountries.

• MicroSaverisaregisteredtrademarkofKensingtonComputerProductsGroup,adivisionofACCOBrands.

• VirtualRemoteToolusesWinI2C/DDClibrary,©NicomsoftLtd.

• Otherproductandcompanynamesmentionedinthisuser’smanualmaybethetrademarksorregisteredtrade-marksoftheirrespectiveholders.

NOTES(1)Thecontentsofthisguidemaynotbereprintedinpartorwholewithoutpermission.

(2)Thecontentsofthisguidearesubjecttochangewithoutnotice.

(3)Great carehasbeen taken in thepreparationof thismanual; however, should younoticeanyquestionablepoints,errorsoromissions,pleasecontactus.

(4)Notwithstandingarticle(3),NECwillnotberesponsibleforanyclaimsonlossofprofitorothermattersdeemedtoresultfromusingtheProjector.

i

Important InformationSafety CautionsPrecautionsPlease read thismanualcarefullybeforeusingyourNECNP3200/NP2200/NP1200projectorandkeep themanualhandyforfuturereference.

CAUTIONToturnoffmainpower,besuretoremovetheplugfrompoweroutlet.Thepoweroutletsocketshouldbeinstalledasneartotheequipmentaspossible,andshouldbeeasilyaccessible.

CAUTIONTOPREVENTSHOCK,DONOTOPENTHECABINET.THEREAREHIGH-VOLTAGECOMPONENTSINSIDE.REFERSERVICINGTOQUALIFIEDSERVICEPERSONNEL.

Thissymbolwarnstheuserthatuninsulatedvoltagewithintheunitmaybesufficienttocauseelectricalshock.Therefore,itisdangeroustomakeanykindofcontactwithanypartinsideoftheunit.

Thissymbolalertstheuserthatimportantinformationconcerningtheoperationandmaintenanceofthisunithasbeenprovided.Theinformationshouldbereadcarefullytoavoidproblems.

WARNING: TOPREVENTFIREORSHOCK,DONOTEXPOSETHISUNITTORAINORMOISTURE.DONOTUSETHISUNIT’SPLUGWITHANEXTENSIONCORDOR INANOUTLETUNLESSALLTHEPRONGSCANBEFULLYINSERTED.

DOC Compliance Notice (for Canada only)ThisClassBdigitalapparatusmeetsallrequirementsoftheCanadianInterference-CausingEquipmentRegulations.

Acoustic Noise Information Ordinance-3. GSGV (for Germany only):Thesoundpressurelevelislessthan70dB(A)accordingtoISO3744orISO7779.

CAUTIONAvoiddisplayingstationaryimagesforaprolongedperiodoftime.DoingsocanresultintheseimagesbeingtemporarilysustainedonthesurfaceoftheLCDpanel.Ifthisshouldhappen,continuetouseyourprojector.Thestaticbackgroundfrompreviousimageswilldisappear.

ii

Important Information

RF Interference (for USA only)

WARNINGTheFederalCommunicationsCommissiondoesnot allowanymodifications or changes to theunitEXCEPTthosespecifiedbyNECDisplaySolutionsofAmerica,Inc.inthismanual.Failuretocomplywiththisgovernmentregulationcouldvoidyourrighttooperatethisequipment.ThisequipmenthasbeentestedandfoundtocomplywiththelimitsforaClassBdigitaldevice,pursuanttoPart15oftheFCCRules.Theselimitsaredesignedtoprovidereasonableprotectionagainstharmfulinterferenceinaresidentialinstallation.Thisequipmentgenerates,uses,andcanradiateradiofrequencyenergyand,ifnotinstalledandusedinaccordancewiththeinstructions,maycauseharmful interferencetoradiocommunications.However, there isnoguaranteethat interferencewillnotoccurinaparticularinstallation.Ifthisequipmentdoescauseharmfulinterferencetoradioortelevisionreception,whichcanbedeterminedbyturningtheequipmentoffandon,theuserisencouragedtotrytocorrecttheinterferencebyoneormoreofthefollowingmeasures:

•Reorientorrelocatethereceivingantenna.

•Increasetheseparationbetweentheequipmentandreceiver.

•Connecttheequipmentintoanoutletonacircuitdifferentfromthattowhichthereceiverisconnected.

•Consultthedealeroranexperiencedradio/TVtechnicianforhelp.

ForUKonly:InUK,aBSapprovedpowercablewithmoldedplughasaBlack(fiveAmps)fuseinstalledforusewiththisequipment.Ifapowercableisnotsuppliedwiththisequipmentpleasecontactyoursupplier.

Turkish RoHS information relevant for Turkish marketEEE Yönetmeliğine Uygundur.

EU-widelegislationasimplementedineachMemberStaterequiresthatusedelectricalandelectronicproductscarryingthemark(left)mustbedisposedofseparatelyfromnormalhouseholdwaste.Thisin-cludesprojectorsandtheirelectricalaccessoriesorlamps.Whenyoudisposeofsuchproducts,pleasefollowtheguidanceofyourlocalauthorityand/orasktheshopwhereyoupurchasedtheproduct.Aftercollectingtheusedproducts,theyarereusedandrecycledinaproperway.Thiseffortwillhelpusreducethewastesaswellasthenegativeimpactsuchasmercurycontainedinalamptothehumanhealthandtheenvironmentattheminimumlevel.ThemarkontheelectricalandelectronicproductsonlyappliestothecurrentEuropeanUnionMemberStates.

Disposing of your used product

WARNING TO CALIFORNIA RESIDENTS:Handlingthecablessuppliedwiththisproductwillexposeyoutolead,achemicalknowntotheStateofCalifor-niatocausebirthdefectsorotherreproductiveharm.WASH HANDS AFTER HANDLING.

iii


10°

Place the projector in a horizontal positionThetiltangleoftheprojectorshouldnotexceed10degrees,norshouldtheprojectorbeinstalledinanywayotherthanthedesktopandceilingmount,otherwiselamplifecoulddecreasedramatically.

Important SafeguardsThesesafety instructionsare toensure the long lifeofyourprojectorand topreventfireandshock.Pleasereadthemcarefullyandheedallwarnings.

Installation•Donotplacetheprojectorinthefollowingconditions:

-onanunstablecart,stand,ortable.

-nearwater,bathsordamprooms.

-indirectsunlight,nearheatersorheatradiatingappliances.

-inadusty,smokyorsteamyenvironment.

-onasheetofpaperorcloth,rugsorcarpets.

•Ifyouwishtohavetheprojectorinstalledontheceiling:

-Donotattempttoinstalltheprojectoryourself.

-Theprojectormustbe installedbyqualifiedtechnicians inorder toensureproperoperationandreducetheriskofbodilyinjury.

-Inaddition,theceilingmustbestrongenoughtosupporttheprojectorandtheinstallationmustbeinaccor-dancewithanylocalbuildingcodes.

-Pleaseconsultyourdealerformoreinformation.

WARNING•Donotcoverthelenswiththelenscaporequivalentwhiletheprojectorison.Doingsocanleadtomeltingofthecapduetotheheatemittedfromthelightoutput.

•Donotplaceanyobjects,whichareeasilyaffectedbyheat,infrontoftheprojectorlens.Doingsocouldleadtotheobjectmeltingfromtheheatthatisemittedfromthelightoutput.

iv


Fire and Shock Precautions• Ensure that there issufficientventilationandthatventsareunobstructed toprevent thebuild-upofheat insideyourprojector.Allowatleast4inches(10cm)ofspacebetweenyourprojectorandawall.• Donottrytotouchtheventilationoutletontheleftfront(whenseenfromthefront)asitcanbecomeheatedwhiletheprojectoristurnedon.

• Preventforeignobjectssuchaspaperclipsandbitsofpaperfromfallingintoyourprojector.Donotattempttore-trieveanyobjectsthatmightfallintoyourprojector.Donotinsertanymetalobjectssuchasawireorscrewdriverintoyourprojector.Ifsomethingshouldfallintoyourprojector,disconnectitimmediatelyandhavetheobjectre-movedbyaqualifiedservicepersonnel.• Donotplaceanyobjectsontopoftheprojector.• Donottouchthepowerplugduringathunderstorm.Doingsocancauseelectricalshockorfire.• Theprojectorisdesignedtooperateonapowersupplyof100-240VAC50/60Hz.Ensurethatyourpowersupplyfitsthisrequirementbeforeattemptingtouseyourprojector.• Donotlookintothelenswhiletheprojectorison.Seriousdamagetoyoureyescouldresult.

• Donotplaceanyobjects,whichareeasilyaffectedbyheat,infrontofaprojectorexhaustvent. Doingsocouldleadtotheobjectmeltingorgettingyourhandsburnedfromtheheatthatisemittedfromtheex-

haust.• Handlethepowercablecarefully.Adamagedorfrayedpowercablecancauseelectricshockorfire.- Donotuseanypowercablesthanthesuppliedone.- Donotbendortugthepowercableexcessively.- Donotplacethepowercableundertheprojector,oranyheavyobject.- Donotcoverthepowercablewithothersoftmaterialssuchasrugs.- Donotheatthepowercable.- Donothandlethepowerplugwithwethands.• Turnoff theprojector,unplugthepowercableandhavetheprojectorservicedbyaqualifiedservicepersonnelunderthefollowingconditions:- Whenthepowercableorplugisdamagedorfrayed.- Ifliquidhasbeenspilledintotheprojector,orifithasbeenexposedtorainorwater.- Iftheprojectordoesnotoperatenormallywhenyoufollowtheinstructionsdescribedinthisuser’smanual.- Iftheprojectorhasbeendroppedorthecabinethasbeendamaged.- Iftheprojectorexhibitsadistinctchangeinperformance,indicatinganeedforservice.• Disconnectthepowercableandanyothercablesbeforecarryingtheprojector• Turnofftheprojectorandunplugthepowercablebeforecleaningthecabinetorreplacingthelamp.• Turnofftheprojectorandunplugthepowercableiftheprojectorisnottobeusedforanextendedperiodoftime.• WhenusingaLANcable: Forsafety,donotconnecttotheconnectorforperipheraldevicewiringthatmighthaveexcessivevoltage.

v

Caution on Handling the Optional LensWhenshippingtheprojectorwiththeoptionallens,removetheoptionallensbeforeshippingtheprojector.Thelensandthelensshiftmechanismmayencounterdamagecausedbyimproperhandlingduringtransportation.Donotholdthelenspartwhencarryingtheprojector.Doingsocouldcausethefocusringtorotate,resultinginaccidentaldroppingoftheprojector.

Lamp Replacement• Toreplacethelamp,followallinstructionsprovidedonpage79.

• Besuretoreplacethelampwhenthemessage[THE LAMP HAS REACHED THE END OF ITS USABLE LIFE. PLEASE REPLACE THE LAMP.]appears.Ifyoucontinuetousethelampafterthelamphasreachedtheendofitsusablelife,thelampbulbmayshatter,andpiecesofglassmaybescatteredinthelampcase.Donottouchthemasthepiecesofglassmaycauseinjury.

Ifthishappens,contactyourdealerforlampreplacement.

A Lamp CharacteristicTheprojectorhasahigh-pressuremercurylampasalightsource.Alamphasacharacteristicthatitsbrightnessgraduallydecreaseswithage.Alsorepeatedlyturningthelamponandoffwillincreasethepossibilityofitslowerbrightness.

CAUTION:

Whenremovingthelampfromaceiling-mountedprojector,makesurethatnooneisundertheprojector.Glassfragmentscouldfallifthelamphasbeenburnedout.


Remote Control Precautions• Handletheremotecontrolcarefully.

• Iftheremotecontrolgetswet,wipeitdryimmediately.

• Avoidexcessiveheatandhumidity.

• Donotheat,takeapart,orthrowbatteriesintofire.

• Ifyouwillnotbeusingtheremotecontrolforalongtime,removethebatteries.

• Ensurethatyouhavethebatteries’polarity(+/−)alignedcorrectly.

• Donotusenewandoldbatteriestogether,orusedifferenttypesofbatteriestogether.

• Disposeofusedbatteriesaccordingtoyourlocalregulations.

Note for US ResidentsThelampinthisproductcontainsmercury.PleasedisposeaccordingtoLocal,StateorFederalLaws.

CAUTION• Always carryyourprojectorbythecarryinghandle.Beforedoingso,besuretolockthecarryinghandleinplace. Tolockthecarryinghandle,see“Tolockthecarryinghandle”onpage6.• Donotusethetilt-footforpurposesotherthanoriginallyintended.Misusessuchasusingthetiltfoottocarryorhang(fromthewallorceiling)theprojectorcancausedamagetotheprojector.• Donotsendtheprojectorinasoftcasebyparceldeliveryserviceorcargoshipment.Theprojectorinsidethesoftcasecouldbedamaged.• Select[HIGH]inFanmodeifyoucontinuetousetheprojectorforconsecutivedays.(Fromthemenu,select[SETUP]→[OPTIONS(1)]→[FANMODE]→[HIGH].)• BeforeusingDirectPowerOff,besuretoallowatleast20minutesimmediatelyafterturningontheprojectorandstartingtodisplayanimage.• Donotunplugthepowercablefromthewalloutletorprojectorwhentheprojectorispoweredon.DoingsocancausedamagetotheACINconnectoroftheprojectorand(or)theprongplugofthepowercable. ToturnofftheACpowersupplywhentheprojectorispoweredon,useapowerstripequippedwithaswitchandabreaker.• Donottrytotouchtheventilationoutletontheleftfront(whenseenfromthefront)asitcanbecomeheatedwhiletheprojectoristurnedonandimmediatelyaftertheprojectoristurnedoff.• Donot turnoff theACpower for60secondsafter the lamp is turnedonandwhile thePOWERindicator isblinkinggreen.Doingsocouldcauseprematurelampfailure.

vi


About High Altitude mode• Set[FANMODE]to[HIGHALTITUDE]whenusingtheprojectorataltitudesapproximately5500feet/1600me-tersorhigher.

Using theprojectorataltitudesapproximately5500feet/1600metersorhigherwithoutsetting to [HIGHALTI-TUDE]cancause theprojector tooverheatand theprotectorcouldshutdown. If thishappens,waitacoupleminutesandturnontheprojector.

• Usingtheprojectorataltitudeslessthanapproximately5500feet/1600metersandsettingto[HIGHALTITUDE]cancausethelamptoovercool,causingtheimagetoflicker.Switch[FANMODE]to[AUTO].

• Using theprojectorataltitudesapproximately5500 feet/1600metersorhighercanshorten the lifeofopticalcomponentssuchasthelamp.

About Copyright of original projected pictures:Pleasenotethatusingthisprojectorforthepurposeofcommercialgainortheattractionofpublicattentioninaven-uesuchasacoffeeshoporhotelandemployingcompressionorexpansionofthescreenimagewiththefollowingfunctionsmayraiseconcernabouttheinfringementofcopyrightswhichareprotectedbycopyrightlaw.[ASPECTRATIO],[KEYSTONE],Magnifyingfeatureandothersimilarfeatures.

vii

Table of Contents

Important Information ............................................................................................i

1. Introduction .......................................................................................................... 1What’sintheBox? ......................................................................................................... 1IntroductiontotheProjector .......................................................................................... 2

CongratulationsonYourPurchaseoftheProjector ................................................. 2Featuresyou’llenjoy: .............................................................................................. 2Aboutthisuser’smanual .......................................................................................... 3

PartNamesoftheProjector .......................................................................................... 4Front/Top .................................................................................................................. 4Rear ......................................................................................................................... 4Bottom...................................................................................................................... 5CarryingtheProjector .............................................................................................. 5TopFeatures ............................................................................................................ 7TerminalPanelFeatures .......................................................................................... 8

PartNamesoftheRemoteControl ............................................................................... 9BatteryInstallation ................................................................................................. 10OperatingRangeforWirelessRemoteControl ...................................................... 10RemoteControlPrecautions .................................................................................. 11

2. Installation and Connections ................................................................... 12SettingUptheScreenandtheProjector ..................................................................... 12

SelectingaLocation[NP3200/NP2200/NP1200]................................................... 12MakingConnections .................................................................................................... 13

ConnectingYourPCorMacintoshComputer ......................................................... 13ConnectinganExternalMonitor ............................................................................ 16ConnectingYourDVDPlayerwithComponentOutput ........................................... 17ConnectingYourVCR............................................................................................. 18ConnectingtoaNetwork........................................................................................ 19ConnectingtheSuppliedPowerCable .................................................................. 20

3. Projecting an Image (Basic Operation) .............................................. 21TurningontheProjector .............................................................................................. 21

NoteonStartupscreen(MenuLanguageSelectscreen) ...................................... 22SelectingaSource ...................................................................................................... 23

Selectingthecomputerorvideosource................................................................. 23AdjustingthePictureSizeandPosition ....................................................................... 24

Adjustingthepositionofaprojectedimage ........................................................... 25Adjustingthefocus(Focusring) ............................................................................ 26Finelyadjustingthesizeofanimage(Zoomlever) ................................................ 26AdjustingtheTiltFoot ............................................................................................ 27

CorrectingKeystoneDistortion .................................................................................... 28CorrectingKeystoneDistortion .............................................................................. 28Adjustingwiththeremotecontrol ........................................................................... 28Adjustingfromthemenu ........................................................................................ 29

OptimizinganRGBImageAutomatically .................................................................... 30AdjustingtheImageUsingAutoAdjust .................................................................. 30

AdjustingVolumeUp&Down ...................................................................................... 30

viii

Table of Contents

7TurningofftheProjector .............................................................................................. 318AfterUse...................................................................................................................... 31

4. Convenient Features ..................................................................................... 32TurningofftheImageandSound ................................................................................ 32FreezingaPicture ....................................................................................................... 32EnlargingaPicture ...................................................................................................... 32ChangingEcoMode .................................................................................................... 33CheckingEnergy-SavingEffect[CARBONMETER] ................................................... 34PreventingtheUnauthorizedUseoftheProjector[SECURITY] ................................. 357UsingtheOptionalRemoteMouseReceiver(NP01MR) ............................................ 388NetworkSettingbyUsinganHTTPBrowser ............................................................... 409UsingtheVGASignalCabletoOperatetheProjector(VirtualRemote) ..................... 43ControllingtheProjectoroveraLAN(PCControlUtilityPro4) ................................... 48

5. Using On-Screen Menu ................................................................................ 50UsingtheMenus .......................................................................................................... 50MenuElements ............................................................................................................ 51ListofMenuItems ....................................................................................................... 52MenuDescriptions&Functions[SOURCE] ................................................................ 54MenuDescriptions&Functions[ADJUST] .................................................................. 55MenuDescriptions&Functions[SETUP] .................................................................... 637MenuDescriptions&Functions[INFO.] ...................................................................... 748MenuDescriptions&Functions[RESET] .................................................................... 76

6. Maintenance ...................................................................................................... 77CleaningorReplacingtheFilter .................................................................................. 77CleaningtheCabinetandtheLens ............................................................................. 78ReplacingtheLamp..................................................................................................... 79

7. Using Optional Lenses ................................................................................. 82TableofThrowDistancesandScreenSizesforOptionalLenses .............................. 82LensShiftAdjustableRange ....................................................................................... 83ReplacingwithOptionalLens ...................................................................................... 84

8. Appendix ............................................................................................................... 86Troubleshooting ........................................................................................................... 86

IndicatorMessages ................................................................................................ 86Specifications .............................................................................................................. 89CabinetDimensions .................................................................................................... 91ScreenSizeandProjectionDistance .......................................................................... 92

[NP3200/NP2200/NP1200] .................................................................................... 92PinAssignmentsofD-SubCOMPUTER1InputConnector ....................................... 94

MiniD-Sub15PinConnector ................................................................................ 94CompatibleInputSignalList ........................................................................................ 95

ix

Table of Contents

7PCControlCodesandCableConnection ................................................................... 96PCControlCodes .................................................................................................. 96CableConnection .................................................................................................. 97PCControlConnector(D-SUB9P) ........................................................................ 97

8TroubleshootingCheckList .......................................................................................... 989TravelCareGuide ....................................................................................................... 100

1

1. Introduction What’s in the Box?Makesureyourboxcontainseverythinglisted.Ifanypiecesaremissing,contactyourdealer.PleasesavetheoriginalboxandpackingmaterialsifyoueverneedtoshipyourProjector.

Lens cap(24FT9741)

Batteries (AAA × 2)

VGA signal cable(7N520073)

NEC Projector CD-ROMUser’s Manual (7N951381)

For North America onlyRegistrationcardLimitedwarranty

For customers in Europe:YouwillfindourcurrentvalidGuaranteePolicyonourWebSite:www.nec-display-solutions.com

• Securitysticker (24L67991)

• Anti-theftscrewforlens×1(24V00841)

• ImportantInformation(ForNorthAmerica:7N8P9891)(ForOthercountriesthanNorthAmerica:7N8P9891and7N8P9901)

• QuickSetupGuide(7N8P9881)

Projector

Powercable(ForNorthAmerica:7N080236)(ForEuropeandothercountries:7N080022)

Remotecontrol(7N900881)

2

1. Introduction

Introduction to the ProjectorThissectionintroducesyoutotheNP3200/NP2200/NP1200projectoranddescribeskeyfeaturesandcontrols.

Congratulations on Your Purchase of the ProjectorTheNP3200/NP2200/NP1200 is a sophisticatedXGAprojector that producesanenhanceddisplay.With theNP3200/NP2200/NP1200youwill beable to project imagesup to 500" (measureddiagonally).Enjoy crispandsharplargescreendisplayfromyourPCorMacintoshcomputer,DVDplayer,VCR,satellitehookup,HDTVsource.TheNP3200/NP2200/NP1200providesforenhancedsecurityoptionstohelpdeterprojectortheftandprovidesforprojectorcontrolthroughthePCcontrolport(D-Sub9Pin)andLANsupport.Withinputandoutputflexibility,longlamplifeandafullfunctionremote,theNP3200/NP2200/NP1200letsyouenjoylargerthanlifeviewingfromacom-pactandeasytosetupanduseprojector.

Features you’ll enjoy :• LCDprojectorwithhighresolutionandhighbrightness

Highresolutiondisplay-uptoUXGAcompatible,XGAnativeresolution.

• Extensiveoptionallens

Onestandardlensandfivetypesofoptionallensesareavailable

• Lensshiftmechanismoffersinstallationflexibility

Manuallensshiftthatcanbeadjustedbyturningdialsonthetopoftheprojector

• Quickstart&QuickPowerOff

Fiveseconds*afterturningonthepower,theprojectorisreadytodisplayPCorvideoimages.

*Thequickstarttimeisonlywhen[STANDBYMODE]issetto[NORMAL]intheon-screenmessage.Thepro-jectorcanbeputawayimmediatelyaftertheprojectorispowereddown.

• DirectPowerOff

Theprojectorhasafeaturecalled“DirectPowerOff”.Thisfeatureallowstheprojectortobeturnedoff(evenwhenprojectinganimage)byusingtheMainPowerSwitchordisconnectingtheACpowersupply.

ToturnofftheACpowersupplywhentheprojectorispoweredon,useapowerstripequippedwithaswitchandabreaker.

NOTE: Before using Direct Power Off, be sure to allow at least 20 minutes immediately after turning on the projector and starting to display an image.

• AutoPowerOn,andAutoPowerOfffunctions

TheAUTOPOWERON(AC),AUTOPOWERON(COMP1/2),AUTOPOWEROFF,andOFFTIMER featureseliminatetheneedtoalwaysusethePOWERbuttonontheremotecontrolorprojectorcabinet.

• Lessthan1Winstandbyconditionwithenergysavingtechnology

Selecting[POWER-SAVING]for[STANDBYMODE]fromthemenucanputtheprojectorinpower-savingmodethatconsumesonly0.4W(100-130VAC)/0.5W(200-240VAC).

• CarbonMeter

Thisfeaturewillshowenergy-savingeffectintermsofCO2emissionreduction(kg)whentheprojector’s[ECOMODE]issetto[ON].

TheamountofCO2emissionreductionwillbedisplayedintheconfirmationmessageatthetimeofpower-offandintheINFOoftheon-screenmenu.

• IntegratedRJ-45connectorforwirednetworkingcapability

AnRJ-45connectorisequippedasstandardfeature.• TheprojectorcanbecontrolledfromacomputeroveraLAN

ConnectingtheprojectortoanetworkallowstheAlertMailsettingandtheprojectorcontrolfromacomputerviathenetwork.

Todoso,youmusthaveanexclusiveapplication“PCControlUtilityPro4”installedonyourcomputerfromthesuppliedNECProjectorCD-ROM.

3

• Avarietyofinputportsandacomprehensivearrayofsystemcontrolinterfaces

Thisprojectorsupportsinputsignalsonthefollowingports:BNC,DVI-D,15pinD-Sub,compositeandS-video.

• WallColorCorrection

Built-inWallColorCorrectionpresetsprovideforadaptivecolorcorrectionwhenprojectingontonon-whitescreenmaterial(orawall).

• Sixpicturepresetmodesforuseradjustablepictureandcolorsettings

Eachpicturepresetmodecanbecustomizedandmemorizedaccordingtoyourpreference.

• Preventingunauthorizeduseoftheprojector

Enhancedsmartsecuritysettingsforkeywordprotection,cabinetcontrolpanellocktohelppreventunauthorizedaccess,adjustmentsandtheftdeterrence.

• ThesuppliedremotecontrolallowsyoutoassignaCONTROLIDtotheprojector

Multipleprojectorscanbeoperatedseparatelyand independentlywith thesamesingleremotecontrolbyas-signinganIDnumbertoeachprojector.

About this user’s manualThefastestwaytogetstartedistotakeyourtimeanddoeverythingrightthefirsttime.Takeafewminutesnowtoreviewtheuser’smanual.Thismaysaveyoutimelateron.Atthebeginningofeachsectionofthemanualyou’llfindanoverview.Ifthesectiondoesn’tapply,youcanskipit.

1. Introduction

4

1. Introduction

Part Names of the Projector

Controls(→ page 7)

Built-inSecuritySlot( )*

ZoomLever(→ page 26)

Lens Cap

RemoteSensor(→ page 10)

Focus Ring(→ page 26)

LensShiftDial(Right/Left,Up/Down)(→ page 25)

AdjustableTiltFootLever(→ page 27)

* ThissecurityslotsupportstheMicroSaver®SecuritySystem.MicroSaver®isaregisteredtrademarkofKens-ingtonMicrowareInc.ThelogoistrademarkedandownedbyKensingtonMicrowareInc.

Ventilation(inlet)/Filter(→ page 77)

AdjustableTiltFoot(→ page 27)

Lens

Front/Top

Ventilation(inlet)/Filter(→ page 77)

StereoSpeaker(5W×2)

AC InputConnectthesuppliedpowercable’sthree-pinplughere,andplugtheotherendintoanactivewalloutlet.(→ page 20)

MainPowerSwitchWhenyouplugthesuppliedpowercableintoanactivewalloutletandturnontheMainPowerswitch,thePOW-ERindicatorturnsorangeandtheprojectorisinstandbymode.(→ page 21)

RemoteSensor(→ page 10)

Ventilation (outlet)Heatedairisexhaustedfromhere.

Rear

TerminalPanel(→ page 8)

LampCover(→ page 79)

LENS RELEASE Button(→ page 84)

5

1. Introduction

Bottom

CarryingHandle

Carrying the ProjectorAlwayscarryyourprojectorbythehandle.Ensurethatthepowercableandanyothercablesconnectingtovideosourcesaredisconnectedbeforemovingtheprojector.Whenmovingtheprojectororwhenitisnotinuse,coverthelenswiththelenscap.

NOTE: To stand the projector on its end, do so by holding the cabinet, not by holding the carrying handle.Doing so can cause damage to the carrying handle.

Anti-theftScrewforLens(→ page 85)

Lock

6

1. Introduction

Tolockthecarryinghandle

1. Carefully place the projector on its end.

2. Pull up the carrying handle with the catch pressed down.

3. Press down the left and right locks to set the carrying handle in place.

• Toplaceback the carryinghandle, pressup the left and rightlocksandpulldownthecarryinghandle.

7

1. Introduction

Top Features

1. POWER Button ( ) (ON / STAND BY) (→page21,31)

NOTE: To turn on the projector, press and hold this button for a minimum of 1 second. To turn off the projector, press this button twice.

2. POWER Indicator (→page21,31,86)

3. STATUS Indicator (→page21,31,86)

4. LAMPIndicator(→page79,86)

5. SOURCEButton(→page23)

6. AUTOADJUSTButton(→page30)

7. KEYSTONE Button (→page28)

8. MENU Button (→page50)

9. / Volume Buttons ( ) (→page30)

10. ENTER Button (→page50)

11. EXIT Button (→page50)

11

1 4

23

567

10

98

8

1. Introduction

Terminal Panel Features

1. COMPUTER1IN/ComponentConnector(MiniD-Sub15Pin)(→page13,16,17)

AUDIOIN(StereoMiniJack)(→page13,16,17)

2. COMPUTER2IN/Component(R/Cr,G/Y,B/Cb,H,V)Connectors(BNC×5)(→page13,18)

AUDIOIN(StereoMiniJack)(→page13)

3. COMPUTER 3 (DVI-D) INConnector (24 Pin)(HDCPcompatible)(→page15)

AUDIOIN(StereoMiniJack)(→page15)

4. S-VIDEOINConnector(MiniDIN4Pin)(→page18)

5. VIDEOINConnector(RCA)(→page18)

6. VIDEO/S-VIDEOAUDIOL/MONO,R (RCA) (→ page18)

7. MONITOR OUT Connector (Mini D-Sub 15 Pin) (→page16)

8. AUDIOOUT(StereoMiniJack)(→page16)

9. PCCONTROLPort(D-Sub9Pin)(→page96,97) Usethisport toconnectyourPCorcontrolsystemto control your projector via a serial cable.Thisenables you to control theprojector using serialcommunicationprotocol.A commercially availableRS232Ccrosscableisrequiredtousethisport.Youcanalso control theprojector byusingPCControlUtilityPro4containedonthesuppliedNECProjec-torCD-ROM.TodosoyoumustfirsthavePCCon-trolUtilityPro4installedonyourPC(→page48).Ifyouarewritingyourownprogram,typicalPCcontrolcodesareonpage96.

10.LANPort(RJ-45)(→page19)

Theactualappearanceoftheterminalpanelmaydifferslightlyfromthatshowninthedrawing,butthisdoesnotaf-fecttheprojector’sperformance.

6 7 9

10 2

154 8

3

9

1. Introduction

Part Names of the Remote Control

＋

3

756

1

2

1012

131114

9

48

26

2728

16172224

2521

15

20

1918

23

29

1. Infrared Transmitter (→page10)

2. POWER ON Button (→page21)

3. POWER OFF Button (→page31)

4,5,6.COMPUTER1/2/3Button (→page23)

7. AUTOADJ.Button (→page30)

8. VIDEO Button (→page23)

9. S-VIDEOButton (→page23)

10. VIEWER Button (notavailableonthisseriesofprojectors)

11. ID SET Button (→page68)

12. Numeric Keypad Button/CLEAR Button (→page68)

13. FREEZE Button (→page32)

14.AV-MUTEButton (→page32)

15.MENUButton (→page50)

16. EXIT Button (→page50)

17. Button (→page50)

18. ENTER Button (→page50)

19. MAGNIFY (+)(–) Button (→page32)

20.MOUSEL-CLICKButton* (→page38, 39)

21.MOUSER-CLICKButton* (→page38, 39)

22. PAGE /Button* (→page38, 39)

23. ECO MODE Button (→page33)

24.KEYSTONEButton (→page28)

25.PICTUREButton (→page55, 56)

26. VOL. (+)(–) Button (→page30)

27. ASPECT Button (→page60)

28. FOCUS/ZOOM Button (notavailableonthisseriesofprojectors)

29. HELP Button (→page74)

* ThePAGE/,MOUSEL-CLICKandMOUSER-CLICKbuttonsworkonlywhentheoptionalremotemousereceiver(NP01MR)isconnectedwithyourcomputer.

10

1. Introduction

Battery Installation

NOTE: Actual operating range may differ slightly from that shown in the drawing.

TIP: You can determine which remote sensor on the projector is enabled in wireless mode. The options are: [FRONT/BACK], [FRONT], or [BACK]. (→ page 68)

• Theinfraredsignaloperatesbyline-of-sightuptoadistanceofabout22feet/7mandwithina60-degreeangleoftheremotesensorontheprojectorcabinet.

• Theprojectorwillnotrespondifthereareobjectsbetweentheremotecontrolandthesensor,orifstronglightfallsonthesensor.

Weakbatterieswillalsopreventtheremotecontrolfromproperlyoperatingtheprojector.

Operating Range for Wireless Remote Control

30°

30°30°

30°

30°

30°30°

30°

Remotesensoronprojectorcabinet

Remotecontrol

Remotecontrol

7m/22feet 7m/22feet

7m/22feet7m/22feet

OPEN

1 Pressfirmlyandslidethebatterycoveroff.

2 Installnewbatteries(AAA).En-surethatyouhavethebatteries’polarity(+/−)alignedcorrectly.

OPEN

3 Slipthecoverbackoverthebat-teriesuntilitsnapsintoplace.Donotmixdifferenttypesofbatter-iesornewandoldbatteries.

11

1. Introduction

Remote Control Precautions• Handletheremotecontrolcarefully.• Iftheremotecontrolgetswet,wipeitdryimmediately.• Avoidexcessiveheatandhumidity.• Donotheat,takeapart,orthrowbatteriesintofire.• Ifyouwillnotbeusingtheremotecontrolforalongtime,removethebatteries.• Ensurethatyouhavethebatteries’polarity(+/−)alignedcorrectly.• Donotusenewandoldbatteriestogether,orusedifferenttypesofbatteriestogether.• Disposeofusedbatteriesaccordingtoyourlocalregulations.

12

1

3

2

ThissectiondescribeshowtosetupyourprojectorandhowtoconnectPCs,videoandaudiosources.

2. Installation and Connections

Setting Up the Screen and the ProjectorSelecting a Location [NP3200/NP2200/NP1200]Thefurtheryourprojectorisfromthescreenorwall,thelargertheimage.Theminimumsizetheimagecanbeisapproximately30 inches(0.76m)measureddiagonallywhentheprojector is roughly41 inches(1.0m) fromthewallorscreen.Thelargesttheimagecanbeis500inches(12.7m)whentheprojectorisabout718inches(18.2m)fromthewallorscreen.Usethedrawingbelowasaguide.

300"

240"

Distance(Unit:m/inch)

Lenscenter

ScreenSize

ScreenSize(unit:cm/inch)

609.6(W)X457.2(H)/240(W)X180(H)

487.7(W)X365.8(H)/192(W)X144(H)

406.4(W)X304.8(H)/160(W)X120(H)

304.8(W)X228.6(H)/120(W)X90(H)

243.8(W)X182.9(H)/96(W)X72(H)

203.2(W)X152.4(H)/80(W)X60(H)

162.6(W)X122.0(H)/64(W)X48(H)

121.9(W)X91.4(H)/48(W)X36(H)

81.3(W)X61.0(H)/32(W)X24(H)

200"

150"

120"100"

80"

10.9/429.1"

8.7/342.5"

7.3/287.4"

5.4/212.6"

4.3/169.3"

3.6/141.7"

2.9/114.2"

2.1/82.68"1.4/

55.12"

40"

60"

TIP: The screen sizes above are intermediate values between tele (minimum display area) and wide (maximum display area) when the standard lens is used. Image size can be adjusted with the zoom adjustment up to a maximum of 15%.For optional lenses, see page 82.

Yourprojectorissimpletosetupanduse.Butbeforeyougetstarted,youmustfirst:

z Setupascreenandtheprojector.

x Connectyourcomputerorvideoequip-ment to theprojector.Seepages13, 15, 16, 17, 18, 19.

c Connect the suppliedpower cable.Seepage20.

NOTE: Ensure that the power cable and any other cables are disconnected before moving the projector. When moving the projector or when it is not in use, cover the lens with the lens cap.

13

COMPUTER1IN

COMPUTER2IN

PHONE


Making ConnectionsConnecting Your PC or Macintosh Computer

NOTE: When using with a notebook PC, be sure to connect the projector and notebook PC while the projector is in standby mode and before turning on the power to the notebook PC.In most cases the output signal from the notebook PC is not turned on unless connected to the projector before being powered up.* If the screen goes blank while using your remote control, it may be the result of the computer’s screen-saver or power manage-

ment software.

Enablingthecomputer’sexternaldisplayDisplayinganimageonthenotebookPC’sscreendoesnotnecessarilymeanitoutputsasignaltotheprojector.WhenusingaPCcompatiblelaptop,acombinationoffunctionkeyswillenable/disabletheexternaldisplay.Usually,thecombinationofthe“Fn”keyalongwithoneofthe12functionkeysgetstheexternaldisplaytocomeonoroff.Forexample,NEClaptopsuseFn+F3,whileDelllaptopsuseFn+F8keycombinationstotogglethroughexternaldisplayselections.

IBMVGAorCompatibles(Notebooktype)orMacintosh(Notebooktype)

NOTE: For older Macintosh, use a commercially available pin adapter (not supplied) to connect to your Mac’s video port.

• Firstturnoffthecomputerandtheprojectorbeforemakingconnections.• Turndownthevolumeon thecomputerbeforeconnectinganaudiocable to theheadphone jackof thecom-puter.Afterconnectingthecomputertotheprojector,youcanadjustthesoundlevelonthecomputerandtheprojectortoyourpreference.

• Youarerecommendedtoconnectanaudiocabletoanaudiooutconnector(minijacktype)ifany.

NOTE: The NP3200/NP2200/NP1200 is not compatible with video decoded outputs of either the NEC ISS-6020 and ISS-6010 switchers.

NOTE: An image may not be displayed correctly when a Video or S-Video source is played back via a commercially available scan converter. This is because the projector will process a video signal as a computer signal at the default setting. In that case, do the following.* When an image is displayed with the lower and upper black portion of the screen or a dark image is not displayed correctly: Project an image to fill the screen and then press the AUTO ADJ button on the remote control or the AUTO ADJUST button on

the projector cabinet.

Stereomini-plugaudiocable(notsupplied)

VGAsignalcable(supplied)TominiD-Sub15-pinconnectorontheprojector.Itisrecommendedthatyouuseacommerciallyavailabledistributionamplifierifconnectingasignalcablelongerthantheonesupplied.

Stereo mini-plugaudiocable (not supplied)

BNC×5cable(notsupplied)

NOTE: Both COMPUTER 1 IN and COMPUTER 3 (DVI-D) IN connectors support Plug & Play (DDC2B).

14


• Selectthesourcenameforitsappropriateinputconnectorafterturningontheprojector.

InputconnectorSOURCEbuttonontheprojector

cabinetButtonontheremotecontrol

COMPUTER1IN COMPUTER1 (COMPUTER1)


COMPUTER3(DVI-D)IN COMPUTER3 (COMPUTER3)

15

COMPUTER3(DVI-D)IN

PHONE

AUDIOIN


WhenViewingaDVIDigitalSignalToprojectaDVIdigitalsignal,besuretoconnectthePCandtheprojectorusingaDVI-Dsignalcable(notsupplied)beforeturningonyourPCorprojector.TurnontheprojectorfirstandselectCOMPUTER3fromthesourcemenubeforeturningonyourPC.Failure to do somaynot activate thedigital output of thegraphics card resulting in nopicturebeingdisplayed.Shouldthishappen,restartyourPC.DonotdisconnecttheDVI-Dsignalcablewhiletheprojectorisrunning.Ifthesignalcablehasbeendisconnectedandthenre-connected,animagemaynotbecorrectlydisplayed.Shouldthishappen,restartyourPC.

NOTE: • UseaDVI-DcablecompliantwiththeDDWG(DigitalDisplayWorkingGroup)DVI(DigitalVisualInterface)revision1.0stan-

dard. The DVI-D cable should be within 5 m (197") long.• TheDVI(DIGITAL)connector(COMPUTER3(DVI-D)IN)acceptsVGA(640×480),SVGA(800×600),1152×864,XGA(1024×768),WXGA(1280×768,1280×800),SXGA(1280×1024@upto60Hz)andSXGA+(1400×1050@upto60Hz).

DVI-D cable(notsupplied)


IBMVGAorCompatiblesorMacintosh

(DVI-DconnectorwithHDCP)




COMPUTER3(DVI-D)IN COMPUTER3 (COMPUTER3)

WhatisHDCP/HDCPtechnology?HDCP is anacronym forHigh-bandwidthDigitalContentProtection.HighbandwidthDigitalContentProtection(HDCP)isasystemforpreventingillegalcopyingofvideodatasentoveraDigitalVisualInterface(DVI).IfyouareunabletoviewmaterialviatheDVIinput,thisdoesnotnecessarilymeantheprojectorisnotfunctioningproperly.Withthe implementationofHDCP,theremaybecases inwhichcertaincontent isprotectedwithHDCPandmightnotbedisplayedduetothedecision/intentionoftheHDCPcommunity(DigitalContentProtection,LLC).

16

AUDIOIN

AUDIOOUT

PHONE

MONITOROUT

COMPUTER1IN


Connecting an External Monitor

Youcanconnectaseparate,externalmonitortoyourprojectortosimultaneouslyviewonamonitortheRGBana-logorcomponentimageyou’reprojecting.

NOTE:• Daisychainconnectionisnotpossible.• TheMONITOROUTconnectorwilloutputnovideosignal(Digitalsignal)fromtheCOMPUTER3(DVI-D)INconnector.• Whenaudioequipmentisconnected,theprojectorspeakerisdisabled.• Whentheprojector is instandbycondition, theMONITOROUTconnectoroutputsthevideosignalandtheAUDIOOUTjackoutputstheaudiosignalaccordingtothesettingof[OUTTERMINAL]inthemenu.

Choicesare[LAST],[COMPUTER1],and[COMPUTER2]. (→ page 73)

VGAsignalcable(supplied)



VGAsignalcable(notsupplied)

(orCOMPUTER2IN/COMPONENTIN)

17


Connecting Your DVD Player with Component Output

TIP: A component signal will be automatically displayed. If not, from the menu, select [SETUP] → [OPTIONS(1)] → [SIGNALSE-LECT]→ [COMPUTER 1 (or 2)] → [COMPONENT]. (→ page 71)

• WhenconnectingtotheCOMPUTER2IN,useacommerciallyavailableRCA(female)-to-BNC(male)adapter.

NOTE:RefertoyourDVDplayer’sowner’smanualformoreinformationaboutyourDVDplayer’svideooutputrequirements.






AUDIO INL R

AUDIO OUT

L R

Component

Y Cb Cr

AUDIO INCOMPUTER 1 IN

Stereominiplug-to-RCAaudiocable(notsupplied)

15-pin-to-RCA(female)×3cableadapter(ADP-CV1E)

ComponentvideoRCA×3cable(notsupplied)

DVDplayer

AudioEquipment

18

AUDIOINL RAUDIOOUT

L R

VIDEOOUTS-VIDEO VIDEO

S-VIDEO IN VIDEO IN

AUDIO IN


Connecting Your VCR

S-Videocable(notsupplied)

Videocable(notsupplied)

VCR

Audioequipment

Audiocable(notsupplied)

TIP:Youcanconnectavideocabletothe“G/Y”connectoroftheCOMPUTER2IN(BNC)connectorstodisplayaVCRsource.Todo so, from the menu, select [SETUP] → [OPTIONS(1)] →[SIGNALSELECT]→ [COMPUTER 2] → [VIDEO]. (→ page 71)




VIDEOIN VIDEO (VIDEO)

S-VIDEOIN S-VIDEO (S-VIDEO)

NOTE:TheAUDIOINLandRjacks(RCA)aresharedbetweentheVideoandS-Videoinputs.

NOTE:RefertoyourVCRowner’smanualformoreinformationaboutyourequipment’svideooutputrequirements.

NOTE: An image may not be displayed correctly when a Video or S-Video source is played back in fast-forward or fast-rewind via a scan converter.

19

Connecting to a Network

Example of LAN connectionExampleofwiredLANconnection


LAN

Server

Hub

LANcable(notsupplied)

NOTE:UseaCategory5orhigherLANcable.

20


Connecting the Supplied Power CableConnectthesuppliedpowercabletotheprojector.Firstconnect thesuppliedpowercable’s three-pinplugto theACINof theprojector,andthenconnect theotherplugofthesuppliedpowercableinthewalloutlet.

NOTE:ToturnofftheACpowersupplywhentheprojectorispoweredon,usetheMainPowerSwitchorapowerstripequippedwith a switch and a breaker.

CAUTION:

Donot try to touch theventilationoutleton the left front (whenseen fromthe front)as itcanbecomeheatedwhiletheprojectoristurnedonandimmediatelyaftertheprojectoristurnedoff.

CAUTION:

Donotunplugthepowercablefromthewalloutletorprojectorwhentheprojectorispoweredon.DoingsocancausedamagetotheACINconnectoroftheprojectorand(or)theprongplugofthepowercable.

AboutDirectPowerOffTheprojectorhasafeaturecalled“DirectPowerOff”.Thisfeatureallowstheprojectortobeturnedoff(evenwhenprojectinganimage)usingtheMainPowerSwitchordisconnectingtheACpowersupply.

NOTE: Before using Direct Power Off, be sure to allow at least 20 minutes immediately after turning on the projector and starting to display an image.

MakesurethattheprongsarefullyinsertedintoboththeACINandthewalloutlet.

Towalloutlet←

21

3. Projecting an Image (Basic Operation)Thissectiondescribeshowtoturnontheprojectorandtoprojectapictureontothescreen.

Turning on the Projector

NOTE:• Theprojectorhastwopowerswitches:amainpowerswitchandaPOWER(ON/STANDBY)button(POWERONandOFFonthe

remote control).• Whenplugginginorunpluggingthesuppliedpowercable,makesurethatthemainpowerswitchispushedtotheoff() po-

sition. Failure to do so may cause damage to the projector.• Theprojectorhasafeaturetoprevent itselffrombeingusedbyunauthorizedindividuals.Tousethisfeature,registerakey-

word. (→ page 35)

1. Remove the lens cap.

• Donot try to remove the lens capbypullingon thestring.Doingsocancausedamage.

2. To turn on the main power to the projector, press the Main Power switch to the on position ( I ).

Theprojectorwillgointostandbymode.Wheninstand-bymode,thePOWERindicatorwilllightorangeandtheSTATUSindicatorwilllightgreenwhen[NORMAL]isse-lectedfor[STANDBYMODE].

SeethePOWERIndicatorsection.(→ page 86)

3. Press the ON/STAND BY button on the projector cab-inet or the POWER ON button on the remote control for 1 second.

ThePOWERindicatorwill turntogreenandtheprojec-torwillbecomereadytouse.

NOTE: When the projector is turned on, it may take some time before the lamp light becomes bright.

TIP: • WhentheSTATUS indicator lightsorange, itmeansthat the[CONTROLPANELLOCK]isturnedon.(→ page 67)

• When themessage “Projector is locked! Enter your pass-word.” isdisplayed, itmeansthatthe[SECURITY] isturnedon. (→ page 36)

After you turn on your projector, ensure that the com-puterorvideosourceisturnedonandthatyourlenscapisremoved.

NOTE: When no signal is available, the NEC logo, blue (default), or black screen will be displayed. When the projector displays the NEC logo, a blue or black screen, the projector will automatically switch to [ECO MODE].The projector will return ECO MODE to its previous setting once an active signal is connected.

Standby Blinking PowerOn

Steadygreen/orangelight

Blinkinggreenlight

Steadygreenlight

(→page86)

Pressthisbuttonforaminimumof1second.

22

3. Projecting an Image (Basic Operation)

Note on Startup screen (Menu Language Select screen)Whenyoufirstturnontheprojector,youwillgettheStartupmenu.Thismenugivesyoutheopportunitytoselectoneofthe21menulanguages.

Toselectamenulanguage,followthesesteps:

1. Use the , , or button to select one of the 21 languages from the menu.

2. Press the ENTER button to execute the selection.

After thishasbeendone,youcanproceed to themenuoperation.Ifyouwant,youcanselect themenu language later.(→ [LANGUAGE]onpage52, 65)

NOTE:• Theprojectorcannotbeturnedofffor60secondsafterthelampisturnedonandwhilethePOWERindicatorisblinkinggreen.• Ifyouturnontheprojectorimmediatelyafterthelampisturnedoff,thefansrunwithoutdisplayinganimageforsometime

and then the projector will display the image. • Immediatelyafterturningontheprojector,screenflickermayoccur.Thisisnormal.Wait3to5minutesuntilthelamplighting

is stabilized.

• Whenthe[ECOMODE]issetto[ON],theLAMPindicatorwilllightgreen.

• Ifoneofthefollowingthingshappens,theprojectorwillnotturnon.

- Iftheinternaltemperatureoftheprojectoristoohigh,theprojectordetectsabnormalhightemperature.Inthisconditiontheprojectorwillnotturnontoprotecttheinternalsystem.If thishappens,waitfortheprojector’sinternalcomponentstocooldown.

- Whenthelampreachesitsendofusablelife,theprojectorwillnotturnon.Ifthishappens,replacethelamp. (→page79)

- Ifthelampfailstolight,andiftheSTATUSindicatorflashesonandoffinacycleofsixtimes,waitafullminuteandthenturnonthepower.

NOTE: Turning the Main Power Switch Off then Back On Allow a minimum of one second between turning off the main power switch and turning it back on again.Thesamewillbeappliedwhenapowerstripequippedwithaswitchandabreakerisused.Failingtodosocouldresultinnopowertotheprojector.(Therewillbenostand-byLED)Should this happen, unplug the power cable and plug it in again. Turn on the main power switch.

23


Selecting a SourceSelecting the computer or video source

NOTE:Turnonthecomputerorvideosourceequipmentconnectedtotheprojector.

SelectingfromSourceListPressandquicklyreleasetheSOURCEbuttonontheprojectorcabinettodis-playtheSourcelist.EachtimetheSOURCEbuttonispressed,theinputsourcewillchangeasfollows:“COMPUTER1”,“COMPUTER2”,“COMPUTER3”,“VID-EO”,“S-VIDEO”.Todisplaytheselectedsource,allow1secondtoelapse.

DetectingtheSignalAutomaticallyPressandholdtheSOURCEbuttonforaminimumof2seconds,theprojectorwillsearchforthenextavailableinputsource.EachtimeyoupressandholdtheSOURCEbuttonforaminimumof2seconds, the inputsourcewillchangeasfollows:

COMPUTER1→COMPUTER2→COMPUTER3→VIDEO→S-VIDEO→ COMPUTER1→ ...

TIP: If no input signal is present, the input will be skipped.

UsingtheRemoteControlPressanyoneoftheCOMPUTER1/2/3,VIDEO,andS-VIDEObuttons.

SelectingDefaultSourceYoucansetasourceasthedefaultsourcesothatitwillbedisplayedeachtimetheprojectoristurnedon.

1. Press the MENU button.

Themenuwillbedisplayed.

2. Press the button twice to select [SETUP] and press the button or the ENTER button to select [GENERAL].

3. Press the button four times to select [OPTIONS(2)].

4. Press the button six times to select [DEFAULT SOURCE SELECT] and press the ENTER button.

The[DEFAULTSOURCESELECT]screenwillbedisplayed.

(→ page 73)

5. Select a source as the default source, and press the ENTER button.

6. Press the EXIT button a few times to close the menu.

7. Restart the projector.

Thesourceyouselectedinstep5willbeprojected.

TIP: When the projector is in Standby mode, applying a computer signal from a computer connected to the COMPUTER 1 IN or COMPUTER 2 IN input will power on the projector and simultaneously project the computer’s image.([AUTO POWER ON(COMP1/2)] → page 73)

24


Usethelensshiftdials,theadjustabletiltfootlevers,thezoomleverorthefocusringtoadjustthepicturesizeandposition.

Adjusting the Picture Size and Position

Intheabovedrawings,cablesareomittedforclarity.

NOTE*: Adjust the throw angle (the height of an image) when the image position is higher than the lens shift adjustable range.

Adjustingthefocus[Focusring]

Adjustingthethrowangle(theheightofanimage)[Tiltfoot]*

Finelyadjustingthesizeofanimage[Zoomlever]

Adjustingtheleftandrighttiltofanimage[Tiltfoot]

Adjustingthekeystonecorrection[Keystone]

Adjustingthepositionofaprojectedimage[Lensshift]

(→page25) (→page26)



25


Adjusting the position of a projected image• Rotate the lens shift dial.

Desktop front projection

Ceiling front projection

Vertical shift

Vertical shift

Max. 0.5V

Max. 0.5V

1V

0.5V

0.1H 0.1H 1H Width of projected image

Shift to left Shift to right

1V Normal projectionPosition

NOTE:ThelensshiftdialforLEFT-RIGHTcannotberotatedone-halfturnormore.Do not over rotate it or it may break.

NOTE: Shifting the lens to the maximum in two directions combined will cause the edges of the image to become dark or will cause some shadows.

TIP: The lens shift dial for UP-DOWN can be rotated one turn or more, but not beyond the adjustable range defined below.

NOTE:LensshiftisnotavailablewiththeNP01FLoptionallens.TheNP01FLshouldbeusedonlyfor“zerodegree”applica-tions.

26


Adjusting the focus (Focus ring)• Rotatethefocusringtomakefocusadjustment.

Finely adjusting the size of an image (Zoom lever)• Rotatethezoomlevertoadjusttheimagesizeonthescreen.

Zoomlever

Focus ring

27

2

2

1

Adjusting the Tilt Foot1. Lift the front edge of the projector.

CAUTION:DonottrytotouchtheventilationoutletduringTiltFootadjustmentasitcanbecomeheatedwhiletheprojectoristurnedonandafteritisturnedoff.

2. Push up the Adjustable Tilt Foot Levers on the right and left sides of the projector to extend the adjustable tilt feet (maximum height).

3. Lower the front of the projector to the desired height.

4. Release the Adjustable Tilt Foot lever to lock the Adjustable tilt foot.

There isapproximately10degrees(up)ofadjustment for the frontoftheprojector.

AdjustableTiltFootLever

AdjustableTiltFootLever

NOTE:Your“Keystone”correctiondatacanberesetbypressingandholdingthe KEYSTONE button for a minimum of 2 seconds.

CAUTION:Donotuse the tilt-foot forpurposesother thanoriginally intended.Misusessuchasusingthetiltfoottocarryorhang(fromthewallorceiling)theprojectorcancausedamagetotheprojector.

TIP: For operating the [KEYSTONE] screen, see “ Correcting Keystone Dis-tortion”onpage28.


4

3

4

AdjustableTiltFoot

28

Correcting Keystone DistortionCorrecting Keystone DistortionIfthescreenistiltedvertically,keystonedistortionbecomeslarge.Proceedwiththefollowingstepstocorrectkeystonedistortion

NOTE: • TheKeystonecorrectioncancauseanimagetobeslightlyblurredbecausethecorrectionismadeelectronically.• TheKeystonecorrectionrangecanbemadenarrower,dependingonasignaloritsaspectratioselection.

Adjusting with the remote control1. Press the KEYSTONE button.

TheKeystonebarwillbedisplayed.

2. Use the or button to correct the keystone distortion.

Adjustsothattherightandleftsidesareparallel.

3. Press the ENTER button.

NOTE:• TheKeystonecorrectioncancauseanimagetobeslightlyblurredbecausethecorrectionismadeelectronically.• Themaximumrangeofverticalkeystonecorrectionis+/−30degrees.Thismaximumrangecanbechangeddependingonthe

signal or aspect ratio setting.• ToresettheKEYSTONEcorrectionsettingvalues,pressandholdtheKEYSTONEbuttonforaminimumof2seconds.• Therangeofkeystonecorrectionisnotthemaximumtiltangleofprojector.• Theleftandright(horizontal)keystonecorrectionisnotavailable.

TIP: The changes can be saved with [KEYSTONE SAVE]. (→ page 63)


ON OFFAUTO ADJ.

COMPUTER

VIDEO S-VIDEO VIEWER

ID SET CLEAR

AV-MUTE FREEZE

ENTER

EXIT

ECO MODEKEYSTONEPICTURE

VOL.HELP FOCUS ASPECT

1 2 3

4 5 6

7 8 9

0

MENU

ZOOM

L-CLICK R-CLICK

MOUSE

PAGE

MAGNIFY

POWER

＋

ON OFFAUTO ADJ.

COMPUTER


ID SET CLEAR

AV-MUTE FREEZE

ENTER

EXIT



1 2 3

4 5 6

7 8 9

0

MENU

ZOOM

L-CLICK R-CLICK

MOUSE

PAGE

MAGNIFY

POWER

＋

ENTER

ON OFFAUTO ADJ.

COMPUTER


ID SET CLEAR

AV-MUTE FREEZE

EXIT



1 2 3

4 5 6

7 8 9

0

MENU

ZOOM

L-CLICK R-CLICK

MOUSE

PAGE

MAGNIFY

POWER

＋

29


Adjusting from the menu1. Press the MENU button.


2. Press the button to select [SETUP] and press the ENTER button.

The[GENERAL]screenwillbedisplayed.

3. Press the button to select [KEYSTONE].

4. Press the or button.

Adjustsothattheimageisrectangular.

5. After completing adjustment, press the EXIT button three times.

Themenuwillbeclosed.

NOTE: The Keystone correction can cause an image to be slightly blurred because the correction is made electronically.

TIP: The changes can be saved with [KEYSTONE SAVE]. (→ page 63)

30


Optimizing an RGB Image AutomaticallyAdjusting the Image Using Auto AdjustOptimizinganRGBimageautomatically.PresstheAUTOADJUST(AUTOADJ.)buttontooptimizeanRGBimageautomatically.Thisadjustmentmaybenecessarywhenyouconnectyourcomputerforthefirsttime.

[Poorpicture]

[Normalpicture]

SoundlevelfromthespeakerandtheAUDIOOUTjack(Stereomini)ontheprojectorcanbeadjusted.

Anotherwaytoadjustvolumeistousethemenu.Select [ADJUST]→ [AUDIO]→ [VOLUME] fromthe menu.

NOTE:• Volumecontrolisnotavailablewiththe or button whenanimageisenlargedbyusingtheMAGNIFY(+)button or when the menu is displayed.

NOTE:• Somesignalsmaytaketimetodisplayormaynotbedisplayedcorrectly.• TheAutoAdjustfunctiondoesnotworkforcomponent,video,S-video,andDVIdigitalsignals.• If theAutoAdjust operation cannot optimize the computer signal, try to adjust [HORIZONTAL], [VERTICAL], [CLOCK], and[PHASE]manually.(→ page 58, 59)

Adjusting Volume Up & Down

Increasevolume

Decreasevolume

31

7 Turning off the ProjectorToturnofftheprojector:


1. Press the POWER (ON/STAND BY) button on the projector cabi-net or the POWER OFF button on the remote control.

The[POWEROFF/AREYOUSURE?/CARBONSAVINGS-SES-SION0.000[g-CO2]]messagewillappear.

2. Press the ENTER button or press the POWER(ON/STAND BY) or the POWER OFF button again.

The lampwill turnoffand theprojectorwill go intostandbymode.Wheninstandbymode,thePOWERindicatorwill lightorangeandtheSTATUSindicatorwilllightgreenwhen[NORMAL]isselectedfor[STANDBYMODE]. Immediately after turningon theprojector anddisplaying an image, you cannot turnoff theprojector for 60 sec-onds.

3. Turn off the Main Power Switch.

Thepowerindicatorwillgoout.

AboutDirectPowerOffTheprojectorhasa featurecalled“DirectPowerOff”.This featureallows theprojector tobe turnedoff (evenwhenprojectingan im-age)using theMainPowerSwitchordisconnecting theACpowersupply.NOTE: Before using Direct Power Off, be sure to allow at least 20 minutes immediately after turning on the projector and starting to display an image.

CAUTION• Donotunplug thepower cable from thewall outlet orprojectorwhen theprojector ispoweredon.DoingsocancausedamagetotheACINconnectoroftheprojectorand(or)theprongplugofthepowercable.ToturnofftheACpowersupplywhentheprojec-torispoweredon,usetheMainPowerSwitch.

• DonotturnofftheACpowersupplywithin10secondsofmakingadjustmentorsettingchangesandclosingthemenu.

Doingsocancauselossofadjustmentsandsettingsandreturntodefault.

8 After UsePreparation: Makesurethatthemainpoweristurnedoff.

1. Unplug the power cable.

2. Disconnect any other cables.

3. Retract adjustable tilt feet if extended.

4. Cover the lens with the lens cap.

32

Turning off the Image and SoundPresstheAV-MUTEbuttontoturnofftheimageandsoundforashortperiodoftime.Pressagaintorestoretheimageandsound.

NOTE:• Eventhoughtheimageisturnedoff,themenustillremainsonthescreen.• SoundfromtheAUDIOOUTjack(Stereomini)canbeturnedoff.

Freezing a PicturePress theFREEZEbutton to freezeapicture.Pressagain to resumemotion.

NOTE: The image is frozen but the original video is still playing back.

Enlarging a PictureYoucanenlargethepictureuptofourtimes.

NOTE: The maximum magnification may be less than four times depending on the signal.

Todoso:

1. Press the MAGNIFY (+) button to magnify the picture.

Tomovethemagnifiedimage,usethe,, or button.

2. Press the button.

Theareaofthemagnifiedimagewillbemoved

3. Press the MAGNIFY (−) button.

EachtimetheMAGNIFY(−)buttonispressed,theimageisreduced.

NOTE: • Theimagewillbeenlargedorreducedatthecenterofthescreen.• Displayingthemenuwillcancelthecurrentmagnification.

4. Convenient Features

＋

＋

Changing Eco ModeThisfeatureenablesyoutoselecttwobrightnessmodesofthelamp:OFFandONmodes.Thelamplifecanbeextendedbyturningonthe[ECOMODE].

[ECOMODE] Description StatusofLAMPindicator

[OFF] Thisisthedefaultsetting(100%Brightness). Off

STATUS

LAMP

[ON] Selectthismodetoincreasethelamplife(approx.80%BrightnessonNP3200andapprox. 88%BrightnessonNP2200/NP1200).

SteadyGreenlight

STATUS

LAMPON OFFAUTO ADJ.

COMPUTER


ID SET CLEAR

AV-MUTE FREEZE

ENTER

EXIT



1 2 3

4 5 6

7 8 9

0

MENU

ZOOM

L-CLICK R-CLICK

MOUSE

PAGE

MAGNIFY

POWER

＋Toturnonthe[ECOMODE],dothefollowing:1. Press the ECO MODE button on the remote control to display

[ECO MODE] screen.

2. Use the or button to select [ON].

3. Press the ENTER button.

Tochangefrom[ON]to[OFF],GobacktoStep2andselect[OFF].Repeat Step 3.

NOTE: • The[ECOMODE]canbechangedbyusingthemenu. Select [SETUP] →[GENERAL]→ [ECO MODE].• The lamp life remaining and lamphoursused canbe checked in [USAGE

TIME]. Select [INFO.] →[USAGETIME].• [ECOMODE]isalwayssetto[OFF]for1minuteimmediatelyafterthelampis

turned on. The lamp condition will not be affected even when [ECO MODE] is changed.

• Aftera lapseof1minute fromwhen theprojectordisplaysablue,blackorlogo screen, [ECO MODE] will automatically switch to [ON].

• Iftheprojectorisoverheatedin[OFF]mode,theremaybeacasewherethe[ECO MODE] automatically changes to [ON] mode to protect the projector. When the projector is in [ON] mode, the picture brightness decreases. When the projector comes back to normal temperature, the [ECO MODE] returns to [OFF] mode.

Thermometer symbol [ ] indicates the [ECO MODE] is automatically set to [ON] mode because the internal temperature is too high.

33


Checking Energy-Saving Effect [CARBON METER]This featurewill showenergy-savingeffect in termsofCO2 emission reduction (kg)when theprojector’s [ECOMODE]issetto[ON].Thisfeatureiscalledas[CARBONMETER].(→page33)

Therearetwomessages:[TOTALCARBONSAVINGS]and[CARBONSAVINGS-SESSION].The[TOTALCARBONSAVINGS]messageshowsthetotalamountofCO2emissionreductionfromthetimeofshipmentuptonow.Youcanchecktheinformationon[USAGETIME]from[INFO.]ofthemenu.(→page74)

The[CARBONSAVINGS-SESSION]messageshowstheamountofCO2emissionreductionbetweenthetimeofchanging toECOMODE immediatelyafter the timeofpower-onand the timeofpower-off.The [CARBONSAV-INGS-SESSION]messagewillbedisplayedinthe[POWEROFF/AREYOUSURE?]messageatthetimeofpower-off.

TIP:• TheformulaasshownbelowisusedtocalculatetheamountofCO2 emission reduction. Amount of CO2 emission reduction = Power consumption in OFF for ECO MODE – Power consumption in ON for ECO MODE x

CO2 conversion factor.* * Calculation for amount of CO2 emission reduction is based on an OECD publication “CO2 Emissions from Fuel Combustion,

2008Edition”.• Thisformulawillnotapplytothepowerconsumptionwhichisnotaffectedbywhether[ECOMODE]isturnedonoroff.

34


Preventing the Unauthorized Use of the Projector [SECURITY]AkeywordcanbesetforyourprojectorusingtheMenutoavoidoperationbyanunauthorizeduser.Whenakey-wordisset,turningontheprojectorwilldisplaytheKeywordinputscreen.Unlessthecorrectkeywordisentered,theprojectorcannotprojectanimage.•The[SECURITY]settingcannotbecancelledbyusingthe[RESET]ofthemenu.

ToenabletheSecurityfunction:



2. Press the button twice to select [SETUP] and press the button or the ENTER button to select [GEN-ERAL].

3. Press the button twice to select [INSTALLATION].

4. Press the button three times to select [SECURITY] and press the ENTER button.

TheOFF/ONmenuwillbedisplayed.

5. Press the button to select [ON] and press the ENTER button.

The[SECURITYKEYWORD]screenwillbedisplayed.

6. Type in a combination of the four buttons and press the ENTER button.

NOTE:Akeywordmustbe4to10digitsinlength.

The[CONFIRMKEYWORD]screenwillbedisplayed.

35


7. Type in the same combination of buttons and press the ENTER button.

Theconfirmationscreenwillbedisplayed.

8. Select [YES] and press the ENTER button.

TheSECURITYfunctionhasbeenenabled.

Toturnontheprojectorwhen[SECURITY]isenabled:

1. Press and hold the POWER button for about 1 second.

Theprojectorwillbeturnedonanddisplayamessagetotheeffectthattheprojectorislocked.


3. Type in the correct keyword and press the ENTER button. The projector will display an image.

NOTE: The security disable mode is maintained until the main power is turned off or unplugging the power cable.

36


TodisabletheSECURITYfunction:



2. Select [SETUP] → [INSTALLATION] → [SECURITY] and press the ENTER button.

TheOFF/ONmenuwillbedisplayed.

3. Select [OFF] and press the ENTER button.

TheKEYWORDCONFIRMATIONscreenwillbedisplayed.

4. Type in your keyword and press the ENTER button.

Whenthecorrectkeywordisentered,theSECURITYfunctionwillbedisabled.

NOTE: If you forget your keyword, contact your dealer. Your dealer will provide you with your keyword in exchange for your re-questcode.YourrequestcodeisdisplayedintheKeywordConfirmationscreen.Inthisexample[K992-45L8-JNGJ-4XU9-1YAT-EEA2]isarequestcode.

37


30˚

30˚

7 Using the Optional Remote Mouse Receiver (NP01MR)Theoptionalremotemousereceiverenablesyoutooperateyourcomputer’smousefunctionsfromtheremotecon-trol.Itisagreatconvenienceforclickingthroughyourcomputer-generatedpresentations.

ConnectingtheremotemousereceivertoyourcomputerIfyouwishtousetheremotemousefunction,connectthemousereceiverandcomputer.Themousereceivercanbeconnecteddirectlytothecomputer’sUSBport(typeA).

NOTE: Depending on the type of connection or OS installed on your computer, you may have to restart your computer or change your computer settings.

Whenoperatingacomputerviatheremotemousereceiver

WhenconnectingusingtheUSBterminalForPC,themousereceivercanonlybeusedwithaWindowsXP*,Windows2000,WindowsVista,Windows7,orMacOSX10.0.0orlateroperatingsystem.

*NOTE:InSP1orolderversionofWindowsXP,ifthemousecursorwillnotmovecorrectly,dothefollowing:Clear the Enhance pointer precision check box underneath the mouse speed slider in the Mouse Properties dialog box [Pointer Options tab].

NOTE:ThePAGE and buttons do not work with PowerPoint for Macintosh.

NOTE: Wait at least 5 seconds after disconnecting the mouse receiver before reconnecting it and vice versa. The computer may not identify the mouse receiver if it is repeatedly connected and disconnected in rapid intervals.

Remotemousereceiver

Computer

ToUSBportofPCorMacintosh

Remotesensorontheremotemousereceiver

7m/22feet

38


Operatingyourcomputer’smousefromtheremotecontrolYoucanoperateyourcomputer’smousefromtheremotecontrol.

PAGE/Button: scrolls theviewingareaof thewindowor tomoveto thepreviousornextslide inPowerPointonyourcomputer.

Buttons: movesthemousecursoronyourcomputer.MOUSEL-CLICKButton: worksasthemouseleftbutton.MOUSER-CLICKButton: worksasthemouserightbutton.

NOTE:• Whenyouoperatethecomputerusingthe or button with the menu displayed, both the menu and the mouse pointer

will be affected. Close the menu and perform the mouse operation.• ThePAGE and buttons do not work with PowerPoint for Macintosh.

AboutDragMode:BypressingtheMOUSEL-CLICKorR-CLICKbuttonfor2or3secondsthenreleasing,thedragmodeissetandthedragoperationcanbeperformedsimplybypressingthebutton.Todroptheitem,presstheMOUSEL-CLICK(orR-CLICK)button.Tocancelit,presstheMOUSER-CLICK(orL-CLICK)button.

TIP: You can change the Pointer speed on the Mouse Properties dialog box on the Windows. For more information, see the user documentation or online help supplied with your computer.

39


8 Network Setting by Using an HTTP BrowserOverviewConnecting theprojector toanetworkallows theAlertMailsetting(→page42)and theprojectorcontrol fromacomputerviathenetwork.Toperformtheprojectorcontrolfromawebbrowser,youmusthaveanexclusiveapplication“PCControlUtilityPro4”installedonyourcomputerfromthesuppliedNECProjectorCD-ROM.TheIPaddressandsubnetmaskoftheprojectorcanbesetontheNetworkSettingscreenofthewebbrowserbyusinganHTTPserverfunction.Pleasebesuretouse“MicrosoftInternetExplorer6.0”orahigherversionforthewebbrowser.(Thisdeviceuses“JavaScript”and“Cookies”andthebrowsershouldbesettoacceptthesefunctions.Thesettingmethodwillvarydependingontheversionofbrowser.Pleaserefertothehelpfilesandtheotherinfor-mationprovidedinyoursoftware.)AccessisgainedtotheHTTPserverfunctionbystartingtheWebbrowseronthecomputerviathenetworkcon-nectedtotheprojectorandenterthefollowingURL.• NetworkSetting

http://<theprojector’sIPaddress>/index.html

• AlertMailSetting

http://<theprojector’sIPaddress>/lanconfig.html

TIP: • ThedefaultIPaddressis“192.168.0.10”.

NOTE: • IfthePROJECTORNETWORKSETTINGSscreendoesnotappearinthewebbrowser,presstheCtrl+F5keystorefreshyour

web browser (or clear the cache).• Thedisplay’sorbutton’sresponsecanbesloweddownoroperationmaynotbeaccepteddependingthesettingsofyournet-

work. Should this happen, consult your network administrator. The projector may not respond if its buttons are repeatedly pressed in rapid intervals. Should this happen, wait a moment and

repeat. If you still can’t get any response, turn off and back on the projector.

Preparation Before UseConnecttheprojectortoacommerciallyavailableLANcablebeforeengaginginbrowseroperations.(→page19)Operationwithabrowserthatusesaproxyservermaynotbepossibledependingonthetypeofproxyserverandthesettingmethod.Althoughthetypeofproxyserverwillbeafactor,itispossiblethatitemsthathaveactuallybeensetwillnotbedisplayeddependingontheeffectivenessofthecache,andthecontentssetfromthebrowsermaynotbereflectedinoperation.Itisrecommendedthataproxyservernotbeusedunlessitisunavoidable.

HandlingoftheAddressforOperationviaaBrowserRegardingtheactualaddressthatisenteredfortheaddressorenteredtotheURLcolumnwhenoperationoftheprojectorisviaabrowser,thehostnamecanbeusedasitiswhenthehostnamecorrespondingtotheIPaddressoftheprojectorhasbeenregisteredtothedomainnameserverbyanetworkadministrator,orthehostnamecor-respondingtotheIPaddressoftheprojectorhasbeensetinthe“HOSTS”fileofthecomputerbeingused.

Example1: Whenthehostnameoftheprojectorhasbeensetto“pj.nec.co.jp”,accessisgainedtothenetworksettingbyspecifying

http://pj.nec.co.jp/index.html fortheaddressortheentrycolumnoftheURL.Example2: WhentheIPaddressoftheprojectoris“192.168.73.1”,accessisgainedtothemailalertsettingsby

specifying http://192.168.73.1/index.html fortheaddressortheentrycolumnoftheURL.

40


NetworkSettingshttp://<theprojector’sIPaddress>/index.html

DHCP ��Enabling this option automatically assigns an IP address to the projector from your DHCP server� Dis-abling this option allows you to register the IP address or subnet mask number obtained from your network administrator�

TIP:YoucanchecktheIPaddressinthemenuwhen[ENABLE]isselectedfor[DHCP].Todoso,fromthe menu, select [INFO.] →[WIREDLAN].

IP ADDRESS ��Set your IP address of the network connected to the projector when [DISABLE] is selected for [DHCP]�

TIP: You can check your specified IP address in the menu. To do so, from the menu, select [INFO.] → [WIREDLAN].

SUBNET MASK ��Set your subnet mask number of the network connected to the projector when [DISABLE] is selected for [DHCP]�

DEFAULT GATEWAY ��Set your default gateway of the network connected to the projector when [DISABLE] is selected for [DHCP]�

DNS (PRIMARY) ��Set your primary DNS settings of the network connected to the projector�DNS (SECONDARY) ��Set your secondary DNS settings of the network connected to the projector�UPDATE ��Reflect your settings�

NOTE: Close the browser after clicking [UPDATE]. The projector will automatically update your set-tings.

TIP:Selecting[NETWORKSETTINGS]for[RESET]fromtheprojector’smenuallowsyoutoreturnthefollowingitemstothefac-tory default.[DHCP]:DISABLE[IP ADDRESS]: 192.168.0.10[SUBNET MASK]: 255.255.255.0[DEFAULTGATEWAY]:192.168.0.1* [DNS(PRIMARY)] and [DNS(SECONDARY)] will remain unchanged.

41


AlertMailSettinghttp://<theprojector’sIPaddress>/lanconfig.html

Thisoptionnotifiesyourcomputerofanerrormessageviae-mailwhenusingwiredLAN.Anerrormessagenotifi-cationwillbesentwhentheprojectorlamphasreachedtheendofitsusablelifeoranerroroccursintheprojector.

HOST NAME ��Type in the hostname of the network connected to the projector� Up to 60 alphanumeric characters can be used� If the host name is unknown, type in a string of characters repre-senting the projector� Example: Projector 1

DOMAIN NAME ��Type in the domain name of the network connected to the projector� Up to 60 alphanu-meric characters can be used� If the domain name is unknown, type in the right side of @ in the sender’s address� Example: nec� com

ALERT MAIL ��Checking [ENABLE] will turn on the Alert Mail feature� Checking [DISABLE] will turn off the Alert Mail feature�

SENDER’S ADDRESS ��Type in the senders address� Up to 60 alphanumeric and symbols characters can be used�SMTP SERVER NAME ��Type in the SMTP server name to be connected to the projector� Up to 60 alphanumeric

characters can be used�RECIPIENT’S ADDRESS 1 to 3 ��Type in your recipient’s address� Up to 60 alphanumeric and symbols characters can be

used�APPLY ��Click this button to reflect the above settingsEXECUTE ��Click this button to send a test mail to check if your settings are correct�STATUS ��A reply to a test mail will be displayed�

NOTE:• Ifyouexecuteatest,youmaynotreceiveanAlertmail.Shouldthishappen,checkifthenetworksettingsarecorrect.• Ifyouenteredanincorrectaddressinatest,youmaynotreceiveanAlertmail.Shouldthishappen,checkiftheRecipient’s

Address is correct

TIP: The Alert Mail settings will not be affected even when [RESET] is done from the menu.

42


9 Using the VGA Signal Cable to Operate the Projector (Virtual Remote)Usingtheutilitysoftware“VirtualRemoteTool”includedonthecompanionNECProjectorCD-ROM,VirtualRemotescreen(ortoolbar)canbedisplayedonyourcomputerscreen.Thiswillhelpyouperformoperationssuchasprojector’spoweronoroffandsignalselectionviatheVGAsignalcable.

VirtualRemotescreen Toolbar

ThissectionprovidesanoutlineofpreparationforuseofVirtualRemoteTool.ForinformationonhowtouseVirtualRemoteTool,seeHelpofVirtualRemoteTool.(→page47)

Step1:InstallVirtualRemoteToolonthecomputer.Step2:Connecttheprojectortothecomputer.(→page45)Step3:StartVirtualRemoteTool.(→page46)

NOTE:• When[COMPUTER1]isselectedfromyoursourceselection,theVirtualRemotescreenorthetoolbarwillbedisplayedaswell

as your computer screen.• UsethesuppliedVGAsignalcabletoconnecttheCOMPUTER1INconnectordirectlywiththemonitoroutputconnectorofthe

computer to use Virtual Remote Tool. UsingaswitcherorothercablesthanthesuppliedVGAsignalcablemaycausefailureinsignalcommunication. VGAcableconnector: PinNos.12and15arerequiredforDDC/CI.• VirtualRemoteToolmaynotworkdependingonyourcomputer’sspecificationsandversionofgraphicadaptersordrivers.

TIP:• Theprojector’sCOMPUTER1INconnectorsupportsDDC/CI(DisplayDataChannelCommandInterface).DDC/CIisastandard

interface for bidirectional communication between display/projector and computer.• ForupdateinformationonVirtualRemoteTool,visitourwebsite:http://www.nec-display.com/dl/en/index.html

Step 1: Install Virtual Remote Tool on the computer

Supported OSVirtualRemoteToolwillrunonthefollowingoperatingsystems.

Windows7HomeBasic*1,Windows7HomePremium*1,Windows7Professional*1,Windows7Enterprise*1, Windows7Ultimate*1

WindowsVistaHomeBasic*1,WindowsVistaHomePremium*1,WindowsVistaBusiness*1,WindowsVistaEnterprise*1,WindowsVistaUltimate*1

WindowsXPHomeEdition*2,WindowsXPProfessional*2,Windows2000Professional*2

*1:Supports32-bitversion.*2:TorunVirtualRemoteTool,“Microsoft.NETFrameworkVersion2.0orlater”isrequired.TheMicrosoft.NETFrameworkVersion2.0orlaterisavailablefromMicrosoft’swebpage.InstalltheMicrosoft.NETFrameworkVersion2.0orlateronyourcomputer.Windows2000ProfessionalsupportsMicrosoft.NETFrameworkVer-sion2.0only.

43


http://www.nec-display.com/dl/en/index.html

Install Virtual Remote ToolPreparation:ExitallrunningprogramsbeforeinstallingVirtualRemoteTool.Ifanotherprogramisrunning,theinstallationmaynot be completed.To installVirtualRemoteTool, theWindowsuser accountmust have [Administrator] privilege(Windows7,WindowsVistaandWindows2000)or[ComputerAdministrator]privilege(WindowsXP).

1 Insert the accompanying NEC Projector CD-ROM into your CD-ROM drive.

ThefoldersinNECProjectorCD-ROMwillbedisplayed.Ifthefoldersarenotdisplayed,right-clicktheCD/DVDdriveiconinWindows’“Computer”(or“MyComputer”)andselect“Open”.

2 Double-click “Software” and then “Virtual Remote Tool”.

The“setup.exe”iconwillbedisplayed.

3 Double-click the “setup.exe” icon.

TheInstallerwillstartandtheWizardscreenwillappear.

4 Click “Next”.

“ENDUSERLICENSEAGREEMENT”screenwillbedisplayed.

Read“ENDUSERLICENSEAGREEMENT”carefully.

5 If you agree, click “I accept the terms in the license agreement” and then click “Next”.

Followtheinstructionsontheinstallerscreenstocompletetheinstallation.

Aftertheinstallationiscompleted,theshortcuticon forVirtualRemoteToolwillbeplacedonthedesktop.

44


TIP:UninstallingVirtualRemoteToolPreparation:ExitVirtualRemoteToolbeforeuninstalling.TouninstallVirtualRemoteTool,theWindowsuseraccountmusthave“Administrator” privilege (Windows7,WindowsVista andWindows2000) or “ComputerAdministrator” privilege(WindowsXP).

•ForWindows7/WindowsVista1 Click “Start” and then “Control Panel”.

TheControlPanelwindowwillbedisplayed.

2 Click “Uninstall a program” under “Programs”

The“ProgramsandFeatures”windowwillbedisplayed.

3 Select Virtual Remote Tool and click it.

4 Click “Uninstall/Change” or “Uninstall”.

•Whenthe“UserAccountControl”windowsisdisplayed,click“Continue”.

Followtheinstructionsonthescreenstocompletetheuninstallation.

•ForWindowsXP/20001 Click “Start” and then “Control Panel”.

TheControlPanelwindowwillbedisplayed.

2 Double-click “Add / Remove Programs”.

TheAdd/RemoveProgramswindowwillbedisplayed.

•OnWindows2000,double-click“Uninstallaprogram”.

3 Click Virtual Remote Tool from the list and then click “Remove”.

Followtheinstructionsonthescreenstocompletetheuninstallation.

Step 2: Connect the projector to the computer1 Use the supplied VGA signal cable to connect the COMPUTER 1 IN connector of the projector directly

with the monitor output connector of the computer.

2 Connect the supplied power cable to the AC IN of the projector and the wall outlet, and then press the Main Power switch to turn on the main power.

Theprojectorisinthestandbycondition.

COMPUTER 1 IN

TIP:• WhenVirtualRemoteToolstartsforthefirsttime,“EasySetup”windowwillbedisplayedtonavigateyourconnections.

ACInputMainPowerSwitch

VGAsignalcable(supplied)

→Towalloutlet

Powercable(supplied)

45


Step 3: Start Virtual Remote Tool1 Double-click the shortcut icon on the Windows Desktop.

WhenVirtualRemoteToolstartsforthefirsttime,“EasySetup”windowwillbedisplayed.

Followtheinstructionsonthescreens

When“EasySetup”iscompleted,theVirtualRemoteToolscreenwillbedisplayed.

TIP:• TheVirtualRemoteToolscreen(orToolbar)canbedisplayedwithoutdisplaying“EasySetup”window. To do so, click to place a check mark for “ DonotuseEasySetupnexttime”onthescreenatStep6in“EasySetup”.

46


ExitingVirtualRemoteTool1 Click the Virtual Remote Tool icon on the Taskbar.

Thepop-upmenuwillbedisplayed.

2 Click “Exit”.

TheVirtualRemoteToolwillbeclosed.

ViewingthehelpfileofVirtualRemoteTool•Displayingthehelpfileusingthetaskbar1 Click the Virtual Remote Tool icon on the taskbar when Virtual Remote Tool is running.


2. Click “Help”.

TheHelpscreenwillbedisplayed.

•DisplayingthehelpfileusingtheStartMenu.1. Click “Start”. “All programs” or “Programs”. “NEC Projector User Supportware”. “Virtual Remote Tool”.

and then “Virtual Remote Tool Help” in this order.


47


Controlling the Projector over a LAN (PC Control Utility Pro 4)Usingtheutilitysoftware“PCControlUtilityPro4”includedonthecompanionNECProjectorCD-ROM,theprojec-torcanbecontrolledfromacomputeroveraLAN.

Control FunctionsPowerOn/Off, signal selection, picture freeze, picturemute, audiomute, adjusting, errormessagenotification,eventschedule.

ScreenofPCControlUtilityPro4

ThissectionprovidesanoutlineofpreparationforuseofPCControlUtilityPro4.ForinformationonhowtousePCControlUtilityPro4,seeHelpofPCControlUtilityPro4.(→ nextpage)

Step1:ConnecttheprojectortoaLAN.Step2:InstallPCControlUtilityPro4onthecomputer.Step3:StartPCControlUtilityPro4.(→ nextpage)

TIP:• PCControlUtilityPro4canbeusedwithaserialconnection.• ForupdateinformationonPCControlUtilityPro4,visitourwebsite: http://www.nec-display.com/dl/en/index.html

Step 1: Connect the projector to a LANConnecttheprojectortotheLANbyfollowingtheinstructionsin“ConnectingtoaNetwork”(→page19)and“NetworkSettingbyUsinganHTTPBrowser”(→page40)

Step 2: Install PC Control Utility Pro 4 on the computer

Supported OSPCControlUtilityPro4willrunonthefollowingoperatingsystems.

Windows7HomeBasic*1,Windows7HomePremium*1,Windows7Professional*1,Windows7Enterprise*1, Windows7Ultimate*1

WindowsVistaHomeBasic*1,WindowsVistaHomePremium*1,WindowsVistaBusiness*1,WindowsVistaEnterprise*1,WindowsVistaUltimate*1

WindowsXPHomeEdition*2,WindowsXPProfessional*2,Windows2000Professional*2

*1:Supports32-bitversion.*2:TorunPCControlUtilityPro4,“Microsoft .NETFrameworkVersion2.0or later” isrequired.TheMicrosoft.NETFrameworkVersion2.0orlaterisavailablefromMicrosoft’swebpage.InstalltheMicrosoft.NETFrame-workVersion2.0orlateronyourcomputer.Windows2000ProfessionalsupportsMicrosoft.NETFrameworkVersion2.0only.

48


InstallPCControlUtilityPro4Preparation: Exitall runningprogramsbefore installingPCControlUtilityPro4. Ifanotherprogram is running, the installationmaynotbecompleted.ToinstallPCControlUtilityPro4,theWindowsuseraccountmusthave[Administrator]privi-lege(Windows7,WindowsVistaandWindows2000)or[ComputerAdministrator]privilege(WindowsXP).

1 Insert the accompanying NEC Projector CD-ROM into your CD-ROM drive.

ThefoldersinNECProjectorCD-ROMwillbedisplayed.

•Ifthefoldersarenotdisplayed,right-clicktheCD/DVDdriveiconinWindows’“Computer”(or“MyComputer”)andselect“Open”.

2 Double-click “Software” and then “PC Control Utility Pro 4”.

The“setup.exe”iconwillbedisplayed.

3 Double-click the “setup.exe” icon.

TheInstallerwillstartandtheWizardscreenwillappear.

4 Click “Next”.

“ENDUSERLICENSEAGREEMENT”screenwillbedisplayed.

Read“ENDUSERLICENSEAGREEMENT”carefully.

5 If you agree, click “I accept the terms in the license agreement” and then click “Next”.

Followtheinstructionsontheinstallerscreenstocompletetheinstallation.

TIP:UninstallingPCControlUtilityPro4 TouninstallPCControlUtilityPro4,do thesameproceduresstatedas in“UninstallingVirtualRemoteTool”.

Read“VirtualRemoteTool”as“PCControlUtilityPro4”(→ page 45)

Step 3: Start PC Control Utility Pro 4Click“Start”→“Allprograms”or“Programs”→“NECProjectorUserSupportware”→“PCControlUtilityPro4”→“PCControlUtilityPro4”.

TIP:ViewingtheHelpofPCControlUtilityPro4•DisplayingtheHelpfileofPCControlUtilityPro4whileitisrunning. Click“Help(H)”→“Help(H)…”ofwindowofPCControlUtilityPro4inthisorder.


•DisplayingthehelpfileusingtheStartMenu. Click“Start”→“Allprograms”or“Programs”→“NECProjectorUserSupportware”→“PCControlUtilityPro4”

→“PCControlUtilityPro4Help”.


49


50

5. Using On-Screen Menu Using the Menus

NOTE: The on-screen menu may not be displayed correctly while interlaced motion video image is projected.

1. Press the MENU button on the remote control or the projector cabinet to display the menu.

NOTE:ThecommandssuchasENTER,EXIT,, in the bottom show available buttons for your operation.

2. Press the buttons on the remote control or the projector cabinet to display the submenu.

3. Press the ENTER button on the remote control or the projector cabinet to highlight the top item or the first tab.

4. Use the buttons on the remote control or the projector cabinet to select the item you want to adjust or set.

You can use the buttons on the remote control or the projector cabinet to select the tab you want.

5. Press the ENTER button on the remote control or the projector cabinet to display the submenu window.

6. Adjust the level or turn the selected item on or off by using the buttons on the remote control or the projector cabinet.

Changesarestoreduntiladjustedagain.

7. Repeat steps 2 -6 to adjust an additional item, or press the EXIT button on the remote control or the pro-jector cabinet to quit the menu display.

NOTE: When a menu or message is displayed, several lines of information may be lost, depending on the signal or settings.

8. Press the MENU button to close the menu.

To return to the previous menu, press the EXIT button.

Menu ElementsSlidebar

Solidtriangle

Tab

Radiobutton

HighAltitudesymbol

Menuwindowsordialogboxestypicallyhavethefollowingelements:

Highlight �� Indicates the selected menu or item� Solid triangle �� Indicates further choices are available� A highlighted triangle indicates the item is active� Tab �� Indicates a group of features in a dialog box� Selecting on any tab brings its page to the front�Radio button ��Use this round button to select an option in a dialog box�Source �� Indicates the currently selected source�Off Timer remaining time �� Indicates the remaining countdown time when the [OFF TIMER] is preset�Slide bar �� Indicates settings or the direction of adjustment�Key Lock symbol �� Indicates the [CONTROL PANEL LOCK] is enabled�Thermometer symbol �� Indicates the [ECO MODE] is forcibly set to [ON] mode because the internal temperature is too

high�High Altitude symbol �� Indicates the [FAN MODE] is set to [HIGH ALTITUDE] mode�

Source

Availablebuttons

Thermometersymbol

KeyLocksymbol

OffTimerremainingtime

Highlight

51

5. Using On-Screen Menu

List of Menu ItemsSomemenuitemsarenotavailabledependingontheinputsource.MenuItem Default Options

SOURCE

COMPUTER1 *COMPUTER2 *COMPUTER3 *VIDEO *S-VIDEO *

ADJUST

PICTURE

PRESET * 1–6

DETAILSETTINGS

GENERAL

REFERENCE *HIGH-BRIGHT,PRESENTATION,VIDEO,MOVIE,GRAPHIC,sRGB

GAMMACORRECTION

DYNAMIC,NATURAL,BLACKDETAIL

COLORTEMPERATURE

* 5000,6500,7800,8500,9300,10500

WHITEBALANCECONTRASTR 0CONTRASTG 0CONTRASTB 0BRIGHTNESSR

0

BRIGHTNESSG

0

BRIGHTNESSB

0

CONTRASTBRIGHTNESSSHARPNESSCOLORHUERESET

IMAGEOPTIONS

CLOCK *PHASE *HORIZONTAL *VERTICAL *OVERSCAN * 0[%],5[%],10[%]ASPECTRATIO * AUTO,4:3,16:9,15:9,16:10,WIDEZOOM,NATIVEPOSITION 0

AUDIO

VOLUMEBASSTREBLEBALANCE3DSURROUND OFF OFF,ON

SETUP

GENERAL

KEYSTONE 0KEYSTONESAVE OFF OFF,ON

WALLCOLOR OFFOFF,WHITEBOARD,BLACKBOARD,BLACKBOARD(GRAY),LIGHTYELLOW,LIGHTGREEN,LIGHTBLUE,SKYBLUE,LIGHTROSE,PINK

ECOMODE OFF OFF,ON

CLOSEDCAPTION OFFOFF,CAPTION1,CAPTION2,CAPTION3,CAPTION4,TEXT1,TEXT2,TEXT3,TEXT4

LANGUAGE ENGLISH

ENGLISH,DEUTSCH,FRANÇAIS,ITALIANO,ESPAÑOL,SVENSKA,日本語DANSK,PORTUGUÊS,ČEŠTINA,MAGYAR,POLSKI,NEDERLANDS,SUOMINORSK,TÜRKÇE,РУССКИЙ, , Ελληνικά, 中文, 한국어

MENU

COLORSELECT COLOR COLOR,MONOCHROMESOURCEDISPLAY ON OFF,ONMESSAGEDISPLAY ON OFF,ONIDDISPLAY ON OFF,ONECOMESSAGE OFF OFF,ONMENUDISPLAYTIME AUTO45SEC MANUAL,AUTO5SEC,AUTO15SEC,AUTO45SECBACKGROUND BLUE BLUE,BLACK,LOGOFILTERMESSAGE 500[H] OFF,100[H],200[H],500[H],1000[H]

* Theasterisk(*)indicatesthatthedefaultsettingvariesdependingonthesignal.

52


SETUP

INSTALLATION

ORIENTATIONDESKTOPFRONT

DESKTOPFRONT,CEILINGREAR,DESKTOPREAR,CEILINGFRONT

CONTROLPANELLOCK OFF OFF,ONSECURITY OFF OFF,ONCOMMUNICATIONSPEED 19200bps 4800bps,9600bps,19200bpsREMOTESENSOR FRONT/BACK FRONT/BACK,FRONT,BACK

CONTROLIDCONTROLIDNUMBER

1 1–254

CONTROLID OFF OFF,ON

OPTIONS(1)

AUTOADJUST NORMAL OFF,NORMAL,FINEFANMODE AUTO AUTO,HIGH,HIGHALTITUDE

SIGNALSELECT

COMPUTER1RGB/

COMPONENTRGB/COMPONENT,RGB,COMPONENT

COMPUTER2RGB/

COMPONENTRGB/COMPONENT,RGB,COMPONENT,VIDEO

COLORSYSTEM

COMPUTER2(VIDEO)

AUTOAUTO,NTSC3.58,NTSC4.43,PAL,PAL-M,PAL-N,PAL60,SECAM

VIDEO AUTOAUTO,NTSC3.58,NTSC4.43,PAL,PAL-M,PAL-N,PAL60,SECAM

S-VIDEO AUTOAUTO,NTSC3.58,NTSC4.43,PAL,PAL-M,PAL-N,PAL60,SECAM

WXGAMODE OFF OFF,ONDEINTERLACE ON OFF,ON

OPTIONS(2)

OFFTIMER OFF OFF,0:30,1:00,2:00,4:00,8:00,12:00,16:00STANDBYMODE NORMAL NORMAL,POWER-SAVINGAUTOPOWERON(AC) OFF OFF,ONAUTOPOWERON(COMP1/2) OFF OFF,ONAUTOPOWEROFF OFF OFF,0:05,0:10,0:20,0:30

DEFAULTSOURCESELECT LASTLAST,AUTO,COMPUTER1,COMPUTER2,COMPUTER3,VIDEO,S-VIDEO

OUTTERMINAL LAST LAST,COMPUTER1,COMPUTER2

INFO.

USAGETIME

LAMPLIFEREMAININGLAMPHOURSUSEDFILTERHOURSUSEDTOTALCARBONSAVINGS

SOURCE

SOURCENAMESOURCEINDEXHORIZONTALFREQUENCYVERTICALFREQUENCYSIGNALTYPEVIDEOTYPESYNCTYPESYNCPOLARITYSCANTYPE

WIREDLAN

PROJECTORNAMEIPADDRESSSUBNETMASKGATEWAYMACADDRESS

VERSION

PRODUCTSERIALNUMBERFIRMWAREDATACONTROLID(when[CONTROLID]isset)

RESET

CURRENTSIGNALALLDATANETWORKSETTINGSCLEARLAMPHOURSCLEARFILTERHOURS

* Theasterisk(*)indicatesthatthedefaultsettingvariesdependingonthesignal.

53


Menu Descriptions & Functions [SOURCE]

COMPUTER1SelectsthecomputerconnectedtoyourCOMPUTER1INinputconnector.NOTE:• WhenthecomponentinputsignalisconnectedtotheCOMPUTER1INconnector,select[COMPUTER1].• TheprojectorwilldetermineiftheinputsignalisRGBorcomponentsignal.

COMPUTER2SelectsthecomputerconnectedtoyourCOMPUTER2INconnectors(BNC×5).NOTE:• WhenthecomponentinputsignalisconnectedtotheCOMPUTER2INconnector,select[COMPUTER2].• TheprojectorwilldetermineiftheinputsignalisRGBorcomponentsignal.

COMPUTER3SelectsthecomputerconnectedtoyourCOMPUTER3(DVI-D)INconnector.

VIDEOSelectswhatisconnectedtoyourVIDEOinput-VCR,DVDplayerordocumentcamera.

S-VIDEOSelectswhatisconnectedtoyourS-VIDEOinput-VCRorDVDplayer.NOTE: A frame may freeze for a brief period of time when a video is played back in fast-forward or fast-rewind with a Video or S-Video source.

54


Menu Descriptions & Functions [ADJUST][PICTURE]

[PRESET]Thisfunctionallowsyoutoselectoptimizedsettingsforyourprojectedimage.Youcanadjustneutraltintforyellow,cyanormagenta.Therearesixfactorypresetsoptimizedforvarioustypesofimages.Youcanalsouse[DETAILSETTINGS]tosetuseradjustablesettingstocustomizeeachgammaorcolor.Yoursettingscanbestoredin[PRESET1]to[PRESET6].

HIGH-BRIGHT �� Recommended for use in a brightly lit room�PRESENTATION �� Recommended for making a presentation using a PowerPoint file�VIDEO �� Recommended for typical TV program viewing�MOVIE �� Recommended for movies�GRAPHIC �� Recommended for graphics�sRGB �� Standard color values

[DETAIL SETTINGS]

55


[GENERAL]StoringYourCustomizedSettings[REFERENCE]Thisfunctionallowsyoutostoreyourcustomizedsettingsin[PRESET1]to[PRESET6].First,selectabasepresetmodefrom[REFERENCE],thenset[GAMMACORRECTION]and[COLORTEMPERA-TURE].

HIGH-BRIGHT �� Recommended for use in a brightly lit room�PRESENTATION �� Recommended for making a presentation using a PowerPoint file�VIDEO �� Recommended for typical TV program viewing�MOVIE �� Recommended for movies�GRAPHIC �� Recommended for graphics�sRGB �� Standard color values�

SelectingGammaCorrectionMode[GAMMACORRECTION]Eachmodeisrecommendedfor:

DYNAMIC �� Creates a high-contrast picture�NATURAL �� Natural reproduction of the picture�BLACK DETAIL �� Emphasizes detail in dark areas of the picture�

AdjustingColorTemperature[COLORTEMPERATURE]Thisoptionallowsyoutoselectthecolortemperatureofyourchoice.

NOTE:When[PRESENTATION]or[HIGH-BRIGHT]isselectedin[REFERENCE],thisfunctionisnotavailable.

AdjustingWhiteBalance[WHITEBALANCE]Thisallowsyoutoadjustthewhitebalance.Contrastforeachcolor(RGB)toadjustthewhitelevelofthescreen;Brightnessforeachcolor(RGB)isusedtoadjusttheblacklevelofthescreen.

[CONTRAST]Adjuststheintensityoftheimageaccordingtotheincomingsignal.

[BRIGHTNESS]Adjuststhebrightnesslevelorthebackrasterintensity.

[SHARPNESS]Controlsthedetailoftheimage.

[COLOR]Increasesordecreasesthecolorsaturationlevel.

[HUE]Variesthecolorlevelfrom+/−greento+/−blue.Theredlevelisusedasreference.

Inputsignal CONTRAST BRIGHTNESS SHARPNESS COLOR HUE

Computer(RGBDIGITAL) Yes Yes Yes No No

Computer(RGBANALOG) Yes Yes Yes No No

Component Yes Yes Yes Yes Yes

Video,S-Video Yes Yes Yes Yes Yes

Yes=Adjustable,No=Notadjustable

56


[RESET]Thesettingsandadjustmentsfor[CONTRAST],[BRIGHTNESS],[SHARPNESS],[COLOR],[HUE],and[REFER-ENCE]within[PRESET]willbereturnedtothefactorysettings.Thesettingsandadjustmentsunder[DETAILSETTINGS]withinthe[PRESET]screenthatarenotcurrentlyselect-edwillnotbereset.

57


[IMAGE OPTIONS]

AdjustingClockandPhase[CLOCK/PHASE]ThisallowsyoutomanuallyadjustCLOCKandPHASE.

CLOCK �� Use this item to fine tune the computer image or to remove any vertical banding that might appear� This function adjusts the clock frequencies that eliminate the horizontal banding in the image� This adjustment may be necessary when you connect your computer for the first time�

PHASE �� Use this item to adjust the clock phase or to reduce video noise, dot interference or cross talk� (This is evident when part of your image appears to be shimmering�) Use [PHASE] only after the [CLOCK] is complete�

58


AdjustingHorizontal/VerticalPosition[HORIZONTAL/VERTICAL]Adjuststheimagelocationhorizontallyandvertically.

- Animagecanbedistortedduringtheadjustmentof[CLOCK]and[PHASE].Thisisnotmalfunction.

- Theadjustments for [CLOCK], [PHASE], [HORIZONTAL],and[VERTICAL]willbestored inmemoryfor thecurrentsignal.Thenexttimeyouprojectthesignalwiththesameresolution,horizontalandverticalfrequency,itsadjustmentswillbecalledupandapplied.

Todeleteadjustmentsstoredinmemory,fromthemenu,youselect[RESET]→[CURRENTSIGNAL]or[ALLDATA]andresettheadjustments.

SelectingOverscanPercentage[OVERSCAN]Selectoverscanpercentage(0%,5%and10%)forsignal.

Projectedimage

Overscanedby10%

NOTE: • The[0[%]]cannotbeselectedwhenVIDEOandS-VIDEOsignalsareused.• [OVERSCAN]isnotavailablewhen[NATIVE]isselectedfor[ASPECTRATIO].

59


SelectingAspectRatio[ASPECTRATIO]Theterm“aspectratio”referstotheratioofwidthtoheightofaprojectedimage.Theprojectorautomaticallydeterminestheincomingsignalanddisplaysitinitsappropriateaspectratio.•Thistableshowstypicalresolutionsandaspectratiosthatmostcomputerssupport.

Resolution AspectRatioVGA 640x480 4:3SVGA 800x600 4:3XGA 1024x768 4:3WXGA 1280x768 15:9WXGA 1280x800 16:10WXGA+ 1440x900 16:10SXGA 1280x1024 5:4SXGA+ 1400x1050 4:3UXGA 1600x1200 4:3

Options FunctionAUTO Theprojectorwillautomaticallydeterminetheincomingsignalanddisplayitinitsas-

pectratio.(→ nextpage)Theprojectormayerroneouslydeterminetheaspectratiodependingonitssignal.Ifthisoccurs,selecttheappropriateaspectratiofromthefollowing.

4:3 Theimageisdisplayedin4:3aspectratio.16:9 Theimageisdisplayedin16:9aspectratio.15:9 Theimageisdisplayedin15:9aspectratio.16:10 Theimageisdisplayedin16:10aspectratio.WIDEZOOM Theimageisstretchedleftandright.

Partsofthedisplayedimagearecroppedattheleftandrightedgesandthereforenotvisible.

NATIVE Theprojectordisplaysthecurrentimageinitstrueresolutionwhentheincomingcom-putersignalhasalowerresolutionthantheprojector’snativeresolution.

[Example]Whentheincomingsig-nalwiththeresolutionof800x600isdisplayed:

NOTE:• Whenanon-computersignalisdisplayed,the[NATIVE]isnotavailable.• Whenasignalwithahigherresolutionthantheprojector’snativeresolutionisdisplayed,[NA-

TIVE] is not available.

60


Sampleimagewhentheappropriateaspectratioisautomaticallydetermined[Computersignal]Aspectratioofincomingsignal 4:3 5:4 16:9 15:9 16:10

Sampleimagewhentheappro-priateaspectratioisautomati-callydetermined

[Videosignal]Aspectratioofincomingsignal 4:3 Letterbox Squeeze

Sampleimagewhentheaspectratioisautomaticallydeter-mined

NOTE:Todisplayasqueezedsignalprop-erly,select[16:9]or[WIDEZOOM].

TIP:• Imagepositioncanbeadjustedverticallyusing[POSITION]whenthe[16:9],[15:9],or[16:10]aspectratiosareselected.• Theterm“letterbox”referstoamorelandscape-orientedimagewhencomparedtoa4:3image,whichisthestandardaspect

ratio for a video source. Theletterboxsignalhasaspectratioswiththevistasize“1.85:1”orcinemascopesize“2.35:1”formoviefilm.• Theterm“squeeze”referstothecompressedimageofwhichaspectratioisconvertedfrom16:9to4:3.

AdjustingtheVerticalPositionofImage[POSITION](onlywhen[16:9],[15:9],or[16:10]isselectedfor[ASPECTRATIO])

When[16:9],[15:9],or[16:10]isselectedin[ASPECTRATIO],theimageisdisplayedwithblackbordersonthetopand bottom.Youcanadjusttheverticalpositionfromthetoptothebottomoftheblackarea.

61


[AUDIO]

ControllingSound[VOLUME/BASS/TREBLE/BALANCE]Adjuststhevolume,bassandtreblelevel,leftandrightbalanceoftheprojectorspeakerandAUDIOOUT(StereoMiniJack).

TIP: [VOLUME]• Whennomenusappear,the and buttonsontheprojectorcabinetandtheVOL.+/−buttonsworkasavolumecontrol.(→

page 30)[BALANCE]• Whentheleft/monauralofthevideo/componentaudioinputisconnected,therightandleftchannelsoundfromtheAUDIOOUT

(Stereo Mini Jack) is the same.

Enabling3DSurround[3DSURROUND]Turnonoroffthe3Dsurroundeffect.

NOTE:When theAUDIOOUT (StereoMini Jack)of theprojector is connected toanexternal equipment, audiocontrolon theexternalequipmentmaycausedistortedorscratchysounddependingontheadjustmentsofBASS,TREBLE,BALANCEand3DSURROUND.Ifthishappens,returntheadjustmentsoftheprojectortothefactorypreset("0"for[BASS],"0"for[TREBLE],and"OFF" for [3D SURROUND]).

62


Menu Descriptions & Functions [SETUP]

[GENERAL]

CorrectingVerticalKeystoneDistortionManually[KEYSTONE]Youcancorrectverticaldistortionmanually.(→page28)

TIP: When this option is highlighted, pressing the ENTER button will display its slide bar for adjustment.

SavingVerticalKeystoneCorrection[KEYSTONESAVE]Thisoptionenablesyoutosaveyourcurrentkeystonesettings.

OFF �� Does not save current keystone correction settings� It will return your keystone correction settings to “zero”�

ON �� Saves current keystone correction settings

Savingyourchangeonceaffectsallsources.Thechangesaresavedwhentheprojectoristurnedoff.

63


UsingtheWallColorCorrection[WALLCOLOR]

Thisfunctionallowsforquickadaptivecolorcorrectioninapplicationswherethescreenmaterialisnotwhite.

NOTE:Selecting[WHITEBOARD]reduceslampbrightness.

SettingEcoMode[ECOMODE]ThisfeatureturnsonorofftheECOmode.Thelamplifecanbeextendedbyselecting[ON].Selecting[ON]alsode-creasesfannoisewhencomparedto[OFF]mode.(→page33)

ECOMODE Description StatusofLAMPindicator

OFFThisistheDefaultsetting(100%Brightness).

Off

ON

Selectthismodetoincreasethelamplife(approx.80%BrightnessonNP3200andapprox.88%BrightnessonNP2200/NP1200).

SteadyGreenlight

NOTE:• The[LAMPLIFEREMAINING]and[LAMPHOURSUSED]canbecheckedin[USAGETIME].Select[INFO.]→[USAGETIME].(→

page 74)• [ECOMODE]isalwayssetto[OFF]for1minuteimmediatelyafterthelampisturnedon.Thelampconditionwillnotbeaf-

fected even when [ECO MODE] is changed.• Afteralapseof1minutefromwhentheprojectordisplaysablue,blackorlogoscreen,[ECOMODE]willautomaticallyswitch

to [ON]. The projector will return to the [OFF] mode once a signal is accepted if the [OFF] is selected.• Iftheprojectorbecomesoverheatedin[OFF]modebecauseofuseinahigh-temperatureroom,theremaybeacasewherethe[ECOMODE]automaticallychangesto[ON]modetoprotecttheprojector.Thismodeiscalled“forcedECOmode”.Whentheprojectorisin[ON]mode,thepicturebrightnessdecreases.TheLAMPindicator’ssteadylightindicatestheprojectorisin[ON]mode. When the projector comes back to normal temperature, the [ECO MODE] returns to [OFF] mode.

Thermometer symbol [ ] indicates the [ECO MODE] is automatically set to [ON] mode because the internal temperature is too high.

64


SettingClosedCaption[CLOSEDCAPTION]ThisoptionsetsseveralclosedcaptionmodesthatallowtexttobesuperimposedontheprojectedimageofVideoorS-Video.

OFF �� This exits the closed caption mode�CAPTION 1-4 �� Text is superimposed�TEXT 1-4 �� Text is displayed�

NOTE:• Theclosedcaptionisnotavailableunderthefollowingconditions:

- when messages or menus are displayed.- when an image is magnified, frozen, or muted.

SelectingMenuLanguage[LANGUAGE]Youcanchooseoneof21languagesforon-screeninstructions.

NOTE: Your setting will not be affected even when [RESET] is done from the menu.

[MENU]

SelectingMenuColor[COLORSELECT]Youcanchoosebetweentwooptionsformenucolor:COLORandMONOCHROME.

TurningOn/OffSourceDisplay[SOURCEDISPLAY]Thisoption turnsonoroff inputnamedisplaysuchasCOMPUTER1,COMPUTER2,COMPUTER3,VIDEO,S-VIDEOandNoInputtobedisplayedonthetoprightofthescreen.

TurningOn/OffMessageDisplay[MESSAGEDISPLAY]MESSAGE DISPLAY �� This option turns on or off messages� Even though selecting [OFF], the following message will appear� •“Projectorislocked”.Whentheprojectorsecurityisunlocked,themessagewilldisappear.

TurningON/OFFControlID[IDDISPLAY]ID DISPLAY �� This option turns on or off the ID number which is displayed when the ID SET button on the remote con-

trol is pressed� (→ page 68)

65


TurningOn/OffEcoMessage[ECOMESSAGE]Thisoptionturnsonoroffthefollowingmessageswhentheprojectoristurnedon.

TheEcoMessagepromptstheusertosaveenergy.When[OFF]isselectedfor[ECOMODE],youwillgetames-sagetopromptyoutoselect[ON]for[ECOMODE].

When[ON]isselectedfor[ECOMODE]

Toclosethemessage,pressanyoneofthebuttons.Themessagewilldisappearifnobuttonoperationisdonefor30 seconds.

When[OFF]isselectedfor[ECOMODE]

PressingtheENTERbuttonwilldisplaythe[ECOMODE]screen.Toclosethemessage,presstheEXITbutton.(→page33, 64)

SelectingMenuDisplayTime[MENUDISPLAYTIME]Thisoptionallowsyoutoselecthowlongtheprojectorwaitsafterthelasttouchofabuttontoturnoffthemenu.Thepresetchoicesare[MANUAL], [AUTO5SEC], [AUTO15SEC],and[AUTO45SEC].The[AUTO45SEC] is thefactorypreset.

SelectingaColororLogoforBackground[BACKGROUND]Usethisfeaturetodisplayablue/blackscreenorlogowhennosignalisavailable.Thedefaultbackgroundis[BLUE].


SelectingIntervalTimeforFilterMessage[FILTERMESSAGE]Thisoptionallowsyoutoselectthetimepreferencebetweendisplayingthemessageforcleaningthefilters.Cleanthefilterwhenyougetthemessage“PLEASECLEANFILTER.”(→page77)Fiveoptionsareavailable:OFF,100[H],200[H],500[H],1000[H]Thedefaultsettingis500[H].


66


[INSTALLATION]

SelectingProjectorOrientation[ORIENTATION]Thisreorientsyourimageforyourtypeofprojection.Theoptionsare:desktopfrontprojection,ceilingrearprojec-tion,desktoprearprojection,andceilingfrontprojection.

DESKTOPFRONT CEILINGREAR

DESKTOPREAR CEILINGFRONT

DisablingtheCabinetButtons[CONTROLPANELLOCK]ThisoptionturnsonorofftheCONTROLPANELLOCKfunction.

NOTE:• ThisCONTROLPANELLOCKdoesnotaffecttheremotecontrolfunctions.• When thecontrolpanel is locked,pressingandholding theEXITbuttonon theprojector cabinet for about10secondswill

change the setting to [OFF].

TIP:Whenthe[CONTROLPANELLOCK]isturnedon,akeylockicon[ ] will be displayed at the bottom right of the menu.

EnablingSecurity[SECURITY]ThisfeatureturnsonorofftheSECURITYfunction.Unlessthecorrectkeywordisentered,theprojectorcannotprojectanimage.(→page35)


67


SelectingCommunicationSpeed[COMMUNICATIONSPEED]ThisfeaturesetsthebaudrateofthePCControlport(D-Sub9P).Itsupportsdataratesfrom4800to19200bps.Thedefaultis19200bps.Selecttheappropriatebaudrateforyourequipmenttobeconnected(dependingontheequipment,alowerbaudratemayberecommendedforlongcableruns).

NOTE: Your selected communication speed will not be affected even when [RESET] is done from the menu.

TurningOnorOffRemoteSensor[REMOTESENSOR]Thisoptiondetermineswhichremotesensorontheprojectorisenabledinwirelessmode.Theoptionsare:FRONT/BACK,FRONT,andBACK.

SettingIDtotheProjector[CONTROLID]YoucanoperatemultipleprojectorsseparatelyandindependentlywiththesingleremotecontrolthathastheCON-TROLIDfunction. IfyouassignthesameIDtoall theprojectors,youcanconvenientlyoperateall theprojectorstogetherusingthesingleremotecontrol.Todoso,youhavetoassignanIDnumbertoeachprojector.

CONTROL ID NUMBER ��Select a number from 1 to 254 you wish to assign to your projector�CONTROL ID ��Select [OFF] to turn off the CONTROL ID setting and select [ON] to turn on the CONTROL ID set-

ting�

NOTE: • Yoursettingwillnotbeaffectedevenwhen[RESET]isdonefromthemenu.•PressingandholdingtheENTERbuttonontheprojectorcabinetfor10secondswilldisplaythemenuforcancelingtheControl

ID.

AssigningorChangingtheControlID1. Turn on the projector.

2. Press the ID SET button on the remote control.

TheCONTROLIDscreenwillbedisplayed.

IftheprojectorcanbeoperatedwiththecurrentremotecontrolID,the[ACTIVE]willbedisplayed.IftheprojectorcannotbeoperatedwiththecurrentremotecontrolID,the[INACTIVE]willbedisplayed.Tooperatetheinactiveprojector,assignthecontrolIDusedfortheprojectorbyusingthefollowingprocedure(Step3).

3. Press one of numeric keypad buttons while pressing and holding the ID SET button on the remote control.

Example:

Toassign“3”,pressthe“3”buttonontheremotecontrol.

NoIDmeansthatalltheprojectorscanbeoperatedtogetherwithasingleremotecontrol.Toset“NoID”,enter“000”orpresstheCLEARbutton.

TIP:TherangeofIDsisfrom1to254.

＋

＋

68


4. Release the ID SET button.

TheupdatedCONTROLIDscreenwillbedisplayed.

NOTE:• TheIDscanbeclearedinafewdaysafterthebatteriesarerundownorremoved.• AccidentallypressinganyoneofthebuttonsoftheremotecontrolwillclearcurrentlyspecifiedIDwithbatteriesremoved.

69


[OPTIONS(1)]

SettingAutoAdjust[AUTOADJUST]ThisfeaturesetstheAutoAdjustmodesothatthecomputersignalcanbeautomaticallyormanuallyadjustedfornoiseandstability.Youcanautomaticallymakeadjustmentintwoways:[NORMAL]and[FINE].

OFF �� The computer signal will not be automatically adjusted� You can manually optimize the computer signal�NORMAL �� Default setting� The computer signal will be automatically adjusted� Normally select this option�FINE �� Select this option if fine adjustment is needed� It takes more time to switch to the source than when

[NORMAL]is selected�

SelectingFanMode[FANMODE]Thisoptionallowsyoutoselectthreemodesforfanspeed:Automode,Highspeedmode,andHighAltitudemode.

AUTO �� The built-in fans automatically run at a variable speed according to the internal temperature�HIGH �� The built-in fans run at high speed�HIGH ALTITUDE �� The built-in fans run at a high speed� Select this option when using the projector at altitudes approximate-

ly 5500 feet/1600 meters or higher�

Whenyouwishtocooldownthetemperatureinsidetheprojectorquickly,select[HIGH].

NOTE: • ItisrecommendedthatyouselectHighspeedmodeifyouusetheprojectornon-stopforconsecutivedays.•Set[FANMODE]to[HIGHALTITUDE]whenusingtheprojectorataltitudesapproximately5500feet/1600metersorhigher.• Usingtheprojectorataltitudesapproximately5500feet/1600metersorhigherwithoutsettingto[HIGHALTITUDE]cancause

the projector to overheat and the protector could shut down. If this happens, wait a couple minutes and turn on the projector.•Usingtheprojectorataltitudeslessthanapproximately5500feet/1600metersandsettingto[HIGHALTITUDE]cancausethelamptoovercool,causingtheimagetoflicker.Switch[FANMODE]to[AUTO].

•Usingtheprojectorataltitudesapproximately5500feet/1600metersorhighercanshortenthelifeofopticalcomponentssuchas the lamp.

• Yoursettingwillnotbeaffectedevenwhen[RESET]isdonefromthemenu.

70


SelectingSignalFormat[SIGNALSELECT][COMPUTER1],[COMPUTER2]Allows you to set [COMPUTER1] and [COMPUTER2] to automatically detect an incomingRGBor componentsourcesuchasacomputerorDVDplayer.HowevertheremaybesomeRGBandcomponentsignalsthatthepro-jectorisunabletodetect.Inthiscase,select[RGB]or[COMPONENT].

NOTE ([COMPUTER 2] only): Whenusingthe"G/Y"connectoroftheCOMPUTER2INconnectorstodisplayaVideosignal,select[VIDEO].

SelectingColorSystem[COLORSYSTEM]Thisfeatureenablesyoutoselectvideostandardsmanually.Normallyselect[AUTO].Selectthevideostandardfromthemenu.ThismustbedonefortheCOMPUTER2INcon-nectors,VIDEO,orS-VIDEOconnectorseparately.

EnablingorDisablingWXGAMode[WXGAMODE]Selecting[ON]willgiveprioritytoaWXGA(1280x768)signalinrecognizinganinputsignal.When[WXGAMODE]issetto[ON],anXGA(1024x768)signalmaynotberecognized.Inthiscase,select[OFF].

Enablingthedeinterlace[DEINTERLACE]Turnsonoroffthedeinterlacefunctionforatelecinesignal.

OFF �� Select this option if there is any jitter or artifacts in video�ON �� Default standard setting�

NOTE:ThisfeatureisnotavailableforRGB,480p,576pandHDTVsignals.

71


[OPTIONS(2)]

UsingOffTimer[OFFTIMER]1. Select your desired time between 30 minutes and 16 hours: OFF, 0:30, 1:00, 2:00, 4:00, 8:00, 12:00, 16:00.

2. Press the ENTER button on the remote control.

3. The remaining time starts counting down.

4. The projector will turn off after the countdown is complete.

NOTE:• Tocancelthepresettime,set[OFF]forthepresettimeorturnoffthepower.• Whentheremainingtimereaches3minutesbeforetheprojectoristurnedoff,the[THEPROJECTORWILLTURNOFFWITHIN

3 MINUTES] message will be displayed on the bottom of the screen.

SelectingPower-savingin[STANDBYMODE]Theprojectorhastwostandbymodes:[NORMAL]and[POWER-SAVING].ThePOWER-SAVINGmodeisthemodethatallowsyoutoputtheprojector inthepower-savingconditionwhichconsumeslesspowerthantheNORMALmode.TheprojectorispresetforNORMALmodeatthefactory.

NORMAL �� Power indicator: Orange light/STATUS indicator: Green lightPOWER-SAVING �� Power indicator: Red light/STATUS indicator: Off

The following connectors, buttons or functions will not work during this mode�- PC CONTROL port, MONITOR OUT connector, and AUDIO OUT connector- LAN and Mail Alert functions- Buttons other than POWER button on the cabinet- Buttons other than POWER ON button on the remote control- Virtual Remote function

NOTE: • When[CONTROLPANELLOCK],[CONTROLID],or[AUTOPOWERON(COMP1/2)]isturnedon,the[STANDBYMODE]setting

is not available.• Yoursettingwillnotbeaffectedevenwhen[RESET]isdonefromthemenu.

EnablingAutoPowerOn[AUTOPOWERON(AC)]Turnstheprojectoronautomaticallywhenthepowercableisinsertedintoanactivepoweroutlet.ThiseliminatestheneedtoalwaysusethePOWERbuttonontheremotecontrolorprojectorcabinet.

72


TurningOntheProjectorByApplyingComputerSignal[AUTOPOWERON(COMP1/2)]WhentheprojectorisinStandbymode,applyingacomputersignalfromacomputerconnectedtotheCOMPUT-ER1INorCOMPUTER2INinputwillpowerontheprojectorandsimultaneouslyprojectthecomputer’simage.ThisfunctionalityeliminatestheneedtoalwaysusethePOWERbuttonontheremotecontrolortheprojectorcabi-nettopowerontheprojector.Tousethisfunction,firstconnectacomputertotheprojectorandtheprojectortoanactiveACinput.

NOTE: • Disconnectingacomputersignal from thecomputerwillnotpoweroff theprojector.We recommendusing this function in

combination of the AUTO POWER OFF function.• Thisfunctionwillnotbeavailableunderthefollowingconditions:

- when a component signal is applied to the COMPUTER1 IN or COMPUTER2 IN connector- whenaSynconGreenRGBsignalorcompositesyncsignalisapplied- when[COMPUTER2]issetto[VIDEO]for[SIGNALSELECT]

• ToenabletheAUTOPOWERON(COMP1/2)afterturningofftheprojector,wait3secondsandinputacomputersignal. If a computer signal is still present when the projector is turned off, the AUTO POWER ON (COMP1/2) will not work and the

projector remains in standby mode.

EnablingPowerManagement[AUTOPOWEROFF]When this option is selected you canenable theprojector to automatically turnoff (at the selected time: 5min.,10min.,20min.,30min.)ifthereisnosignalreceivedbyanyinputorifnooperationisperformed.

SelectingDefaultSource[DEFAULTSOURCESELECT]Youcansettheprojectortodefaulttoanyoneofitsinputseachtimetheprojectoristurnedon.

LAST �� Sets the projector to default to the previous or last active input each time the projector is turned on�AUTO �� Searches for an active source in order of COMPUTER1 → COMPUTER2 → COMPUTER3 → VIDEO → S-

VIDEO → COMPUTER1 and displays the first found source�COMPUTER1 �� Displays the computer signal from the COMPUTER 1 IN connector every time the projector is turned on�COMPUTER2 �� Displays the computer signal from the COMPUTER 2 IN connector every time the projector is turned on� COMPUTER3 �� Displays the DVI digital from the COMPUTER 3 (DVI-D) IN connector every time the projector is turned

on� VIDEO �� Displays the Video source from the VIDEO IN connector every time the projector is turned on�S-VIDEO �� Displays the Video source from the S-VIDEO IN connector every time the projector is turned on�

SettingMONITOROUTConnector[OUTTERMINAL]ThisoptionallowsyoutodeterminewhichRGBorcomponentsourceisoutputfromtheMONITOROUTconnectorduringStandbymode.

LAST �� The signal from the last COMPUTER 1 or COMPUTER 2 input will be output to the MONITOR OUT con-nector and AUDIO OUT jack�

COMPUTER 1 �� The signal from the COMPUTER 1 input will be output to the MONITOR OUT connector and AUDIO OUT jack�

COMPUTER 2 �� The signal from the COMPUTER 2 input will be output to the MONITOR OUT connector and AUDIO OUT jack�

NOTE:When[COMPUTER1]or[COMPUTER2]isselectedfor[AUTOPOWERON(COMP1/2)],the[OUTTERMINAL]featureisnot available.

73


7 Menu Descriptions & Functions [INFO.]Displaysthestatusofthecurrentsignalandlampusage.Thisitemhasfourpages.

TIP:PressingtheHELPbuttonontheremotecontrolwillshowthe[INFO.]menuitems.

Theinformationincludedisasfollows:

[USAGE TIME]

[LAMPLIFEREMAINING](%)*[LAMPHOURSUSED](H)[FILTERHOURSUSED](H)[TOTALCARBONSAVINGS](kg-CO2)

* Theprogressindicatorshowsthepercentageofremainingbulblife.

Thevalueinformsyouoftheamountoflampusage.Whentheremaininglamptimereaches0,theLAMPLIFEREMAININGbarindicatorchangesfrom0%to100Hoursandstartscountingdown.

Iftheremaininglamptimereaches0hours,theprojectorwillnotturnonregardlessofwhethertheECOMODEissettoOFForON.

• ThemessagetotheeffectthatthelamporthefiltersshouldbereplacedwillbedisplayedforoneminutewhentheprojectoristurnedonandwhenthePOWERbuttonontheprojectorortheremotecontrolispressed.

Todismissthismessage,pressanybuttonontheprojectorortheremotecontrol.

Lamp life(H)Replacement lampECO MODE

OFF ON2000 3000 NP06LP

• [TOTALCARBONSAVINGS]

Thisdisplaystheestimatedcarbonsavinginformationinkg.Thecarbonfootprintfactorinthecarbonsavingcal-culationisbasedontheOECD(2008Edition).

74


[SOURCE]

[SOURCENAME] [SOURCEINDEX][HORIZONTALFREQUENCY] [VERTICALFREQUENCY][SIGNALTYPE] [VIDEOTYPE][SYNCTYPE] [SYNCPOLARITY][SCANTYPE]

[WIRED LAN]

[PROJECTORNAME] [IPADDRESS][SUBNETMASK] [GATEWAY][MACADDRESS]

[VERSION]

[PRODUCT][SERIALNUMBER][FIRMWARE]Version[DATA]Version[CONTROLID](when[CONTROLID]isset)

75


8 Menu Descriptions & Functions [RESET]

ReturningtoFactoryDefault[RESET]TheRESETfeatureallowsyoutochangeadjustmentsandsettingstothefactorypresetfora(all)source(s)exceptthefollowing:

[CURRENTSIGNAL]Resetstheadjustmentsforthecurrentsignaltothefactorypresetlevels.Theitemsthatcanberesetare:[PRESET],[CONTRAST],[BRIGHTNESS],[SHARPNESS],[COLOR],[HUE],[CLOCK],[PHASE],[HORIZONTAL],[VERTICAL],[OVERSCAN],and[ASPECTRATIO].

[ALLDATA]Resetalltheadjustmentsandsettingsforallthesignalstothefactorypreset.All items canbe resetEXCEPT [LANGUAGE], [BACKGROUND], [FILTERMESSAGE], [SECURITY], [COM-MUNICATIONSPEED],[CONTROLID], [FANMODE],[STANDBYMODE],[LAMPLIFEREMAINING], [LAMPHOURSUSED],[FILTERHOURSUSED],[TOTALCARBONSAVINGS],and[NETWORKSETTINGS].Toresetthelampusagetime,see“ClearingLampHourMeter[CLEARLAMPHOURS]”below.

ClearingNetworkingSettings[NETWORKSETTINGS]Returns[DHCP],[IPADDRESS],[SUBNETMASK],and[GATEWAY]tothedefaultsettings.

ClearingLampHourMeter[CLEARLAMPHOURS]Resets the lampclockback tozero.Selecting thisoptiondisplayssubmenu foraconfirmation.Select [YES]andpresstheENTERbutton.

NOTE: Elapsed time of the lamp use will not be affected even when [RESET] is done from the menu.

NOTE: The projector will turn off and go into standby mode when you continue to use the projector for another 100 hours after the lamp has reached the end of its life. In this condition you cannot clear the lamp hour meter on the menu. If this happens, presstheHELPbuttonontheremotecontrolfor10secondstoresetthelampclockbacktozero.Dothisonlyafterreplacingthelamp.

ClearingtheFilterUsageHours[CLEARFILTERHOURS]Resets thefilterusagebacktozero.Selectingthisoptiondisplayssubmenuforaconfirmation.Select [YES]andpresstheENTERbutton.

NOTE: Elapsed time of the filter use will not be affected even when [RESET] is done from the menu.

76


77

6. MaintenanceThissectiondescribesthesimplemaintenanceproceduresyoushouldfollowtocleanthefiltersandreplacethelamp.

Cleaning or Replacing the FilterTheair-filterspongekeepsdustanddirtfromgettinginsidetheprojectorandshouldbefrequentlycleaned.Ifthefilterisdirtyorclogged,yourprojectormayoverheat.

NOTE: The message for filter cleaning will be displayed for one minute when the projector is turned on or off.To cancel the message, press any button on the projector cabinet or the remote control.

CAUTION• Turnofftheprojector,turnoffthemainpowerswitchandunplugtheprojectorbeforereplacingthefilter.

• Onlycleantheoutsideofthefiltercoverwithavacuumcleaner.

• Donotattempttooperatetheprojectorwithoutthefiltercover.

Tocleantheair-filter:Vacuumthefilter-throughthefiltercover.

Toresetthefilterusagetime,fromthemenu,select[RESET]→[CLEARFILTERHOURS].(→page76forresettingthefilterusagetime)

Toreplacethefilter(sponge):

CAUTION• Replacebothfiltersatthesametime.

• Beforereplacingthefilters,removedustanddirtfromtheprojectorcabinet.

• Theprojectorcontainshigh-precisionparts.Keepoutdustanddirtduringfilterreplacement.

• Donotwashthefilterwithwater.Waterwilldamagethefiltermembrane.

• Reattachthefiltercovercorrectly.Failuretodosomaycauseprojectormalfunction.

Preparation:Replacethelampbeforereplacingthefilters.

NOTE: When you replace the lamp, it is also wise to replace the filter. The filter comes in the same package with your replacement lamp.

1. Pull to remove the filter cover.

Filter

78

6. Maintenance

2. Gently peel off the filter (sponge) and replace it with the new one.

3. Reinstall the filter cover.

• Slipthefiltercoverbackuntilitsnapsintoplace.

4. Connect the supplied power cable, turn on the Main Power switch and turn on the projector.

5. Finally, select the menu → [RESET] → [CLEAR FILTER HOURS] to reset the filter usage hours.

(→ page 76 for resetting the filter usage time)

Cleaning the Cabinet and the Lens1. Turn off the projector before cleaning.

2. Clean the cabinet periodically with a damp cloth. If heavily soiled, use a mild detergent. Never use strong detergents or solvents such as alcohol or thinner.

3. Use a blower or lens paper to clean the lens, and be careful not to scratch or mar the lens.

79

Replacing the LampWhenthelampreachestheendof its life,theLAMPindicator inthecabinetwillblinkred.Eventhoughthelampmaystillbeworking,replacethelamptomaintaintheoptimalprojectorperformance.Afterreplacingthelamp,besuretoclearthelamphourmeter.(→page76)

CAUTION

• DONOTTOUCHTHELAMPimmediatelyafterithasbeenused.Itwillbeextremelyhot.Turntheprojectoroff,turnoffthemainpowerswitchandthendisconnectthepowercable.Allowatleastonehourforthelamptocoolbeforehandling.

• DONOTREMOVEANYSCREWSexcepttwolamphousingscrews.Youcouldreceiveanelectricshock.

• Donotbreaktheglassonthelamphousing.

Keepfingerprintsoff theglasssurfaceonthe lamphousing.Leavingfingerprintsontheglasssurfacemightcauseanunwantedshadowandpoorpicturequality.

• Theprojectorwillturnoffandgointostandbymodewhenyoucontinuetousetheprojectorforanother100hoursafterthelamphasreachedtheendofitslife.Ifthishappens,besuretoreplacethelamp.Ifyoucontinuetousethelampafterthelampreachestheendofitslife,thelampbulbmayshatter,andpiecesofglassmaybescatteredinthelampcase.Donottouchthemasthepiecesofglassmaycauseinjury.Ifthishappens,contactyourNECdealerforlampreplacement.

To replace the lamp:Optionallampandtoolsneededforreplacement:

• ReplacementlampNP06LP

• Phillipsscrewdriverorequivalent

1. Use a Philips screwdriver to push and release the tab.

Push and pull to remove the lamp cover.

6. Maintenance

1

2

80

6. Maintenance

2. Loosen the two screws securing the lamp housing until the phillips screwdriver goes into a freewheeling condition. The two screws are not removable.

Remove the lamp housing by holding it.

NOTE: There is an interlock on this case to prevent the risk of electrical shock. Do not attempt to circumvent this interlock.

3. Insert a new lamp housing until the lamp housing is plugged into the socket.

CAUTIONDonotusealampotherthantheNECreplacementlampNP06LP.OrderthisfromyourNECdealer.

Secure it in place with the two screws.

Be sure to tighten the screws.

Interlock

81

6. Maintenance

5. Connect the supplied power cable, turn on the Main Power switch and turn on the projector.

6. Finally, select the menu → [RESET] → [CLEAR LAMP HOURS] to reset the lamp life remaining and lamp usage hours.

NOTE: When you continue to use the projector for another 100 hours after the lamp has reached the end of its life, the projector cannot turn on and the menu is not displayed.Ifthishappens,presstheHELPbuttonontheremotecontrolfor10secondstoresetthelampclockbacktozero.Whenthelamptimeclockisresettozero,theLAMPindicatorgoesout.

4. Reattach the lamp cover.

Slip the lamp cover back until it snaps into place.

1

2

82

7. Using Optional LensesFiveoptionallensesareavailablefortheNP3200/NP2200/NP1200.Seetheinformationdescribedonthispagetobuytheappropriatelensforyourscreensizeandthrowdistance.Seepage84forinstallingthelens.

Table of Throw Distances and Screen Sizes for Optional Lenses [NP3200/NP2200/NP1200]Screen Size

STANDARD1.5− 2.0

(m) (inches)

NP02ZL1.2 −1.5

(m) (inches)

NP03ZL1.9 − 3.1

(m) (inches)

NP04ZL3.0 − 4.8

(m) (inches)

NP05ZL4.7−7.2

(m) (inches)

NP01FL0.8

(m) (inches) 30" 40" 60" 67" 72" 80" 84" 90" 100" 120" 150" 180" 200" 210" 240" 250" 270" 300" 400" 500"

0.89 – 1.20 1.20 – 1.62 1.83 – 2.45 2.05 – 2.75 2.21 – 2.96 2.46 – 3.29 2.59 – 3.46 2.78 – 3.71 3.09 – 4.13 3.72– 4.96 4.66 – 6.21 5.60 – 7.47 6.23 – 8.30 6.54 – 8.72 7.49 – 9.97 7.80 – 10.39 8.43 – 11.23 9.37 – 12.48 12.51 – 16.66 15.65 – 20.83

0.70 – 0.92 0.95 – 1.25 1.44 – 1.89 1.62 – 2.12 1.74 – 2.28 1.94 – 2.54 2.04 – 2.67 2.19 – 2.86 2.44 – 3.18 2.93 – 3.83 3.68 – 4.80 4.42 – 5.77 4.92 – 6.41 5.17 – 6.74 5.91 – 7.71 6.16 – 8.03 6.66 – 8.67 7.41 – 9.64 9.89 – 12.87 12.37 – 16.10

27.5– 36.4 37.3– 49.1 56.9– 74.5 63.7– 83.4 68.6– 89.8 76.4– 99.9 80.3 – 105.0 86.2– 112.6 96.0– 125.4 115.5– 150.8 144.9 – 188.9 174.2– 227.1 193.8 – 252.5 203.5– 265.2 232.9 – 303.4 242.7– 316.1 262.2– 341.5 291.5– 379.7 389.3 – 506.8 487.1– 634.0

1.56 – 2.51 2.37 – 3.79 2.66 – 4.25 2.86 – 4.57 3.19 – 5.08 3.35 – 5.34 3.60 – 5.73 4.01 – 6.37 4.82 – 7.66 6.05 – 9.59 7.27 – 11.53 8.08 – 12.81 8.49 – 13.46 9.72 – 15.39 10.12 – 16.04 10.94 – 17.33 12.16 – 19.26 16.24 – 25.70 20.32 – 32.15

61.4– 98.6 93.5– 149.4 104.7– 167.1 112.8 – 179.8 125.6– 200.1 132.0 – 210.3 141.7– 225.5 157.7– 250.8 189.8 – 301.6 238.0 – 377.7 286.2– 453.8 318.3 – 504.5 334.3 – 529.9 382.5– 606.0 398.6– 631.4 430.7– 682.1 478.8– 758.2 639.4– 1011.9 799.9– 1265.6

3.60 – 5.83 4.03 – 6.53 4.34 – 7.03 4.84 – 7.82 5.09 – 8.22 5.46 – 8.81 6.08 – 9.81 7.32 – 11.79 9.18 – 14.77 11.05 – 17.75 12.29 – 19.73 12.91 – 20.73 14.77 – 23.70 15.39 – 24.70 16.63 – 26.68 18.49 – 29.66 24.70 – 39.59 30.90 – 49.52

141.7– 229.7 158.8– 257.0 171.1– 276.6 190.6– 307.9 200.4 – 323.5 215.0– 346.9 239.5– 386.0 288.3 – 464.2 361.6– 581.5 434.9 – 698.7 483.8 – 776.9 508.2– 816.0 581.5– 933.3 605.9– 972.4 654.8– 1050.5 728.1– 1167.8 972.4– 1558.7 1216.7– 1949.5

5.69 – 8.75 6.38 – 9.80 6.87 – 10.54 7.65 – 11.73 8.05 – 12.33 8.63 – 13.23 9.62 – 14.72 11.58 – 17.70 14.52 – 22.17 17.46 – 26.65 19.43 – 29.63 20.41 – 31.12 23.35 – 35.59 24.33 – 37.08 26.29 – 40.06 29.23 – 44.54 39.04 – 59.45 48.85 – 74.36

224.1 – 344.6 251.1 – 385.7 270.4 – 415.0 301.3 – 462.0 316.8– 485.5 340.0 – 520.7 378.6– 579.4 455.8– 696.8 571.7– 872.9 687.5– 1049.0 764.8– 1166.4 803.4 – 1225.1 919.3 – 1401.2 957.9– 1459.9 1035.1– 1577.3 1151.0– 1753.5 1537.2– 2340.5 1923.4 – 2927.5

0.640.98 1.10 1.18 1.32 1.39 1.49 1.662.00 2.50

25.338.643.3 46.651.954.658.665.378.698.6

35.1– 47.3 47.4– 63.8 72.2– 96.6 80.8 – 108.2 87.0– 116.4 96.9– 129.5 101.8 – 136.1 109.3 – 146.0 121.6– 162.4 146.3– 195.3 183.4 – 244.6 220.5– 294.0 245.3– 326.9 257.6– 343.3 294.7– 392.6 307.1– 409.1 331.8 – 442.0 368.9– 491.3 492.5– 655.8 616.2– 820.2

Forscreensizesbetween30"and500"notindicatedontheabovetable,useformulasbelow.

ThrowdistanceforStandardlens(m/inch)=H×1.5throughH×2.0Distancefrom0.89mto20.83m/35.1"to820.2"ThrowdistanceforNP01FL(m/inch)=H×0.8Distancefrom0.64mto2.5m/25.3"to98.6"ThrowdistanceforNP02ZL(m/inch)=H×1.2throughH×1.5Distancefrom0.7mto16.1m/27.5"to634"ThrowdistanceforNP03ZL(m/inch)=H×1.9throughH×3.1Distancefrom1.56mto32.15m/61.4"to1265.6"ThrowdistanceforNP04ZL(m/inch)=H×3.0throughH×4.8Distancefrom3.6mto49.52m/141.7"to1949.5"ThrowdistanceforNP05ZL(m/inch)=H×4.7throughH×7.2Distancefrom5.69mto74.36m/224.1"to2927.5"“H”=Screenwidth

STANDARD (H X 1.5) - (H X 2.0)

NP01FL (H X 0.8)

NP03ZL (H X 1.9) - (H X 3.1)

NP04ZL (H X 3.0) - (H X 4.8)

NP05ZL (H X 4.7) - (H X 7.2)

NP02ZL (H X 1.2) - (H X 1.5)

Example:Distancefroma100"screenwiththelensNP03ZLReferringtothediagramonpage93,“H”is2.0m/78.7".Therefore,theprojectiondistancesof100inchesarefrom2.0m/78.7"×1.9to2.0m/78.7"×3.1=from3.8m/150"to6.2m/244".

NOTE: The values in the tables are design values and may vary.

83

7. Using Optional Lenses

Lens Shift Adjustable RangeThetoprightdiagramshowsthelocationoftheimagepositioninthelens.Thelenscanbeshiftedwithintheshad-edareaasshownusingthenormalprojectionpositionasastartingpoint.Theprojectorhasalensshiftfeaturethatallowsyoutomovetheimageverticallyorhorizontally.

NOTE:LensshiftisnotavailablewiththeNP01FLoptionallens.TheNP01FLshouldbeusedonlyfor“zerodegree”applications.

Desktop front projection

Ceiling front projection

Vertical shift

Vertical shift

Max. 0.5V

Max. 0.5V

1V

0.5V

0.1H 0.1H 1H Width of projected image

Shift to left Shift to right

1V Normal projectionPosition

84


2. Pull out the existing lens slowly.

Removetheexistinglensfromtheprojector.

1. Rotate the lens counterclockwise while strongly pushing the LENS RELEASE button all the way in.

Theexistinglenswillbedisengaged.

NOTE:IfthelenscannotberemovedevenbyusingtheLENSRELEASEbut-ton, the anti-theft screw for lens may be used to secure the lens. If such is the case, remove the anti-theft screw first. (→ next page)

LENS RELEASE Button

Replacing with Optional Lens

CAUTION• Donotgiveashockorexcessiveloadtotheprojectororthelenscomponentsastheprojectorandlenscompo-nentscontainprecisionparts.

• Whenshippingtheprojectorwiththeoptionallens,removetheoptionallensbeforeshippingtheprojector.Thelensandthelensshiftmechanismmayencounterdamagecausedbyimproperhandlingduringtransportation.

• Beforeremovingorinstallingthelens,besuretoturnofftheprojector,waituntilthecoolingfansstop,andturnoffthemainpowerswitch.

• Donottouchthelenssurfacewhenremovingorinstallingthelens.

• Keepfingerprints,dustoroiloffthelenssurface.Donotscratchthelenssurface.

• Workonalevelsurfacewithasoftclothunderittoavoidscratching.

• Ifyouremoveandstorethelens,attachthelenscaptotheprojectortokeepoffdustanddirt.

• PleaseheedthefollowinginformationifyouowntwoormoreNP3200/NP2200/NP1200projectorsandmayin-terchangethestandardlenses.

Whenreplacingthestandardlens(withanoptionallens)andthenre-installingthestandardlensbackintotheprojector,thestandardlensmustgobacktoitsoriginalprojectorfromwhichitwasremoved.

If you remove the standard lens fromoneNP3200/NP2200/NP1200projector and re-install it into anotherNP3200/NP2200/NP1200projector,performancemaybecompromised.

Besuretousethestandardlensincombinationwithitsoriginalfactory-adjustedprojector.

85


Using the anti-theft screw to prevent theft of the lens Tighten the supplied anti-theft screw on the front bottom.

Holeofanti-theftscrewforlensunit

Installthenewlens

1. Insert the lens with the yellow protrusion on top.

2. Rotate the lens clockwise.

Rotatethelensuntilyoufeelitclickintoplace.

YellowProtrusion

86

8. Appendix TroubleshootingThissectionhelpsyouresolveproblemsyoumayencounterwhilesettinguporusingtheprojector.

Indicator MessagesPOWER Indicator

Indicator Condition ProjectorCondition Note

Off The main power is off –

Blinking light Green 0�5 sec On,0�5 sec Off

The projector is getting ready to turn on� Wait for a moment�

2�5 sec On,0�5 sec Off

Off Timer is enabled� –

Steady light Green The projector is turned on� –

Orange [NORMAL] is selected for [STANDBY MODE] –

Red [POWER-SAVING] is selected for [STANDBY MODE]

–

STATUS Indicator


Off Normal or Standby ([POWER-SAVING] for [STANDBY MODE]) –

Blinking light Red 1 cycle (0�5 sec On, 2�5 sec Off)

Lamp cover error or lamp housing error Replace the lamp cover or lamp housing cor-rectly�

2 cycle (0�5 sec On, 0�5 sec Off)

Temperature error The projector is overheated� Move the projector to a cooler location�


Power error Power unit is not working properly� Contact your dealer�


Fan error Fans will not work correctly�


Lamp error Lamp fails to light� Wait a full minute and then turn on again�

Green Re-firing the lamp (The projector is cooling down�)

The projector is re-firing�Wait for a moment�

Steadylight Green Standby ([NORMAL] for [STANDBY MODE]) –Orange CONTROL PANEL LOCK is on� You have pressed cabinet button when Control

Panel Lock is on�CONTROL ID error Remote control ID and projector ID are not

matched�

LAMP Indicator


Off Normal –

Blinking light Red Lamp has reached its end of life� Lamp replace-ment message will be displayed�

Replace the lamp�

Steady light Red Lamp has been used beyond its limit� The projec-tor will not turn on until the lamp is replaced�

Replace the lamp�

Green [ECO MODE] is set to [ON] –

Over-TemperatureProtectionIfthetemperatureinsidetheprojectorrisestoohigh,theover-temperatureprotectorwillautomaticallyturnoffthelampwiththeSTATUSindicatorblinking(2-cycleOnandOff.)Shouldthishappen,dothefollowing:• Unplugthepowercableafterthecoolingfansstop.• Movetheprojectortoacoolerlocationiftheroomwhereyouarepresentingisparticularlytoowarm.• Cleantheventilationholesiftheyarecloggedwithdust.• Waitabout60minutesuntiltheinsideoftheprojectorbecomescoolenough.

87

8. Appendix

Common Problems & Solutions (→“POWER/STATUS/LAMPIndicator”onpage86)

Problem CheckTheseItems

Does not turn onor shut down

• Checkthatthepowercableispluggedinandthatthepowerbuttonontheprojectorcabinetortheremotecontrolis on� (→ pages 20, 21)

• Ensurethatthelampcoverisinstalledcorrectly.(→ page 81)• Checktoseeiftheprojectorhasoverheated.Ifthereisinsufficientventilationaroundtheprojectororifthe

room where you are presenting is particularly warm, move the projector to a cooler location�• Checktoseeifyoucontinuetousetheprojectorforanother100hoursafterthelamphasreachedtheendof

its life� If so, replace the lamp� After replacing the lamp, reset the lamp hours used� (→ page 76)• Thelampmayfailtolight.Waitafullminuteandthenturnonthepoweragain.• Set[FANMODE]to[HIGHALTITUDE]whenusingtheprojectorataltitudesapproximately5500feet/1600meters

or higher� Using the projector at altitudes approximately 5500 feet/1600 meters or higher without setting to [HIGH ALTITUDE] can cause the projector to overheat and the projector could shut down� If this happens, wait a couple minutes and turn on the projector� (→ page 70)

If you turn on the projector immediately after the lamp is turned off, the fans run without displaying an image for some time and then the projector will display the image� Wait for a moment�

Will turn off • Ensurethatthe[OFFTIMER]or[AUTOPOWEROFF]isoff.(→ page 72, 73)No picture • UsetheCOMPUTER1,theCOMPUTER2,theCOMPUTER3,theVIDEOortheS-VIDEObuttonontheremote

control to select your source (Computer, Video or S-Video)� (→ page 23) If there is still no picture, press the button again�

• Ensureyourcablesareconnectedproperly.• Usemenustoadjustthebrightnessandcontrast.(→ page 56)• Removethelenscap.• Resetthesettingsoradjustmentstofactorypresetlevelsusingthe[RESET]intheMenu.(→ page 76)• EnteryourregisteredkeywordiftheSecurityfunctionisenabled.(→ page 35)• BesuretoconnecttheprojectorandnotebookPCwhiletheprojectorisinstandbymodeandbeforeturning

on the power to the notebook PC�In most cases the output signal from the notebook PC is not turned on unless connected to the projector before being powered up�* If the screen goes blank while using your remote control, it may be the result of the computer’s screen-saver

or power management software�• Seealsothenext page�

Picture suddenly becomes dark

• CheckiftheprojectorisintheForcedECOmodebecauseoftoohighambienttemperature.Ifthisisthecase,lower the internal temperature of the projector by selecting [HIGH] for [FAN MODE]� (→ page 70)

Color tone or hue is unusual

• Checkifanappropriatecolorisselectedin[WALLCOLOR].Ifso,selectanappropriateoption.(→ page 64)• Adjust[HUE]in[PICTURE].(→ page 56)

Image isn’t square to the screen

• Repositiontheprojectortoimproveitsangletothescreen.(→ page 24)• UsetheKeystonecorrectionfunctiontocorrectthetrapezoiddistortion.(→ page 28)

Picture is blurred • Adjustthefocus.(→ page 26)• Repositiontheprojectortoimproveitsangletothescreen.(→ page 24)• Ensure that the distance between the projector and screen is within the adjustment range of the lens.

(→ page 82, 83)• Condensationmayformonthelensiftheprojectoriscold,broughtintoawarmplaceandisthenturnedon.

Should this happen, let the projector stand until there is no condensation on the lens�Flicker appears on screen

• Set [FAN MODE] to other than [HIGH ALTITUDE] mode when using the projector at altitudes approximately 5500 feet/1600 meters or lower� Using the projector at altitudes less than approximately 5500 feet/1600 meters and setting to [HIGH ALTITUDE] can cause the lamp to overcool, causing the image to flicker� Switch [FAN MODE] to [AUTO]� (→ page 70)

Image is scrolling vertically, horizontally or both

• Checkthecomputer’sresolutionandfrequency.Makesurethattheresolutionyouaretryingtodisplayissup-ported by the projector� (→ page 95)

• AdjustthecomputerimagemanuallywiththeHorizontal/Verticalinthe[IMAGEOPTIONS].(→ page 59)Remote control does not work

• Installnewbatteries.(→ page 10)• Makesuretherearenoobstaclesbetweenyouandtheprojector.• Standwithin22feet(7m)oftheprojector.(→ page 10)• Checkifoneormoreremotesensorsareenabled.Select[SETUP]→ [INSTALLATION] → [REMOTE SENSOR]

from the menu� (→ page 68)• Makesurethattheremotecontrol'sIDcorrespondswiththeprojector'sID.(→ page 68)

Indicator is lit or blinking • SeethePOWER/STATUS/LAMPIndicator.(→ page 86)Cross color in RGB mode

• PresstheAUTOADJ.buttonontheprojectorcabinetortheremotecontrol.(→ page 30)• Adjustthecomputerimagemanuallywith[CLOCK]/[PHASE]in[IMAGEOPTIONS]inthemenu.(→ page 58)

Formoreinformationcontactyourdealer.

88

8. Appendix

Ifthereisnopicture,orthepictureisnotdisplayedcorrectly.

• PoweronprocessfortheprojectorandthePC.

BesuretoconnecttheprojectorandnotebookPCwhiletheprojectorisinstandbymodeandbeforeturningonthepowertothenotebookPC.

InmostcasestheoutputsignalfromthenotebookPCisnotturnedonunlessconnectedtotheprojectorbeforebeingpoweredup.

NOTE:Youcancheckthehorizontalfrequencyofthecurrentsignalintheprojector’smenu[SOURCE]underInformation.Ifitreads“0kHz”,thismeansthereisnosignalbeingoutputfromthecomputer.Seepage75 or go to next step.

• Enablingthecomputer’sexternaldisplay.

DisplayinganimageonthenotebookPC’sscreendoesnotnecessarilymeanitoutputsasignaltotheprojec-tor.WhenusingaPCcompatiblelaptop,acombinationoffunctionkeyswillenable/disabletheexternaldisplay.Usually,thecombinationofthe“Fn”keyalongwithoneofthe12functionkeysgetstheexternaldisplaytocomeonoroff.Forexample,NEClaptopsuseFn+F3,whileDell laptopsuseFn+F8keycombinationstotogglethroughexternaldisplayselections.

• Non-standardsignaloutputfromthecomputer

IftheoutputsignalfromanotebookPCisnotanindustrystandard,theprojectedimagemaynotbedisplayedcorrectly.Should thishappen,deactivate thenotebookPC’sLCDscreenwhentheprojectordisplay is inuse.EachnotebookPChasadifferentwayofdeactivate/reactivatethelocalLCDscreensasdescribedintheprevi-ousstep.Refertoyourcomputer’sdocumentationfordetailedinformation.

• ImagedisplayedisincorrectwhenusingaMacintosh

WhenusingaMacintoshwiththeprojector,settheDIPswitchoftheMacadapter(notsuppliedwiththeprojec-tor)accordingtoyourresolution.Aftersetting,restartyourMacintoshforthechangestotakeaffect.

Forsettingdisplaymodesother thanthosesupportedbyyourMacintoshandtheprojector,changingtheDIPswitchonaMacadaptermaybounceanimageslightlyormaydisplaynothing.Shouldthishappen,settheDIPswitchtothe13"fixedmodeandthenrestartyourMacintosh.Afterthat,restoretheDIPswitchestoadisplay-ablemodeandthenrestarttheMacintoshagain.

NOTE: A Video Adapter cable manufactured by Apple Inc. is needed for a PowerBook which does not have a mini D-Sub 15-pin connector.

• MirroringonaPowerBook

* WhenusingtheprojectorwithaMacintoshPowerBook,outputmaynotbesetto1024×768unless“mirroring”isoffonyourPowerBook.Refertoowner’smanualsuppliedwithyourMacintoshcomputerformirroring.

• FoldersoriconsarehiddenontheMacintoshscreen

Foldersoriconsmaynotbeseenonthescreen.Shouldthishappen,select[View]→[Arrange]fromtheApplemenuandarrangeicons.

89

8. Appendix

SpecificationsThissectionprovidestechnicalinformationabouttheprojector’sperformance.

ModelNumber NP3200/NP2200/NP1200

OpticalLCDPanel NP3200/NP2200/NP1200:0.8"p-SiTFTactive-matrixwithMicroLens

Array(Aspectratio4:3)Resolution NP3200/NP2200/NP1200:1024×768pixels*¹uptoUXGAwithscaling

technology(uptoSXGA+@60HzonDVI-D)StandardLens Manualzoomandfocus: F1.7–2.2 f=24.4–32.5mmLamp NP3200:330WAC(264WinEcomode) NP2200/NP1200:300WAC(264WinEcomode)LightOutput*², *³ NP3200:5000lumens(approx.80%inEco) NP2200:4200lumens(approx.88%inEco) NP1200:3700lumens(approx.88%inEco)ContrastRatio*³(fullwhite:fullblack)NP3200/NP2200/NP1200:600:1ImageSize(Standardlens) 30"–500"(0.76m–12.7m)diagonalLensOptions Fixedlens: NP01FL(throwratio0.8:1) Zoomlens: NP02ZL(throwratio1.2–1.5:1) NP03ZL(throwratio1.9–3.1:1) NP04ZL(throwratio3.0–4.8:1) NP05ZL(throwratio4.7–7.2:1) LensShift: Vertical+/−0.5V,Horizontal+/−0.1H*1 Effective pixels are more than 99.99%.*2Thisisthelightoutputvalue(lumens)whenthe[PRESET]modeissetto[HIGH-BRIGHT].Ifanyothermodeisselectedasthe

[PRESET] mode, the light output value may drop slightly.*3 Compliance with ISO21118-2005

ElectricalInputs 1AnalogRGB(MiniD-Sub15P),1AnalogRGBR/Cr,G/Y,B/Cb,H,V

(BNC×5),1DigitalRGB(DVI-D24P,HDCPsupported),2Component(MiniD-Sub15P&BNC)sharedwithCOMPUTER1&2IN,1S-Video(MiniDIN4P),1Video(RCA),3StereoMiniAudio,2(L/R)RCAAudio

Outputs 1RGB(MiniD-Sub15P),1StereoMiniAudioPCControl 1PCControlPort(D-Sub9P)LANPort RJ-45VideoCompatibility NTSC,NTSC4.43,PAL,PAL60,PAL-N,PAL-M,SECAM, DTV:480i,480p,720p,1080i(60Hz) 576i,576p,1080i(50Hz) DVD:Progressive(50/60Hz)ScanRate Horizontal:15kHzto100kHz(RGB:24kHzorover) Vertical:50Hzto120HzVideoBandwidth RGB:90MHz(Max.)ColorReproduction 16.7millioncolorssimultaneously,FullcolorHorizontalResolution NTSC/NTSC4.43/PAL/PAL-M/PAL-N/PAL60:540TVlines SECAM:300TVlines RGB:1024dots(H)×768dots(V)ExternalControl RS232,IR,LANSyncCompatibility SeparateSync/CompositeSync/SynconGBuilt-inSpeakers 5W×2PowerRequirement 100–240VAC,50/60HzInputCurrent NP3200:4.7-2.0A NP2200/NP1200:4.3-1.9A

90

8. Appendix

PowerConsumption NP3200: 428W(100-130VAC)/412W(200-240VAC) inOFF forECOMODE/345W(100-130VAC)/334W(200-240VAC) inON forECOMODE

NP2200/NP1200:396W(100-130VAC)/381W(200-240VAC)inOFFforECOMODE/345W(100-130VAC)/334W(200-240VAC)inONforECOMODE

NP3200/NP2200/NP1200: 12W(100-130VAC)/13W(200-240VAC) inNORMALMode forSTANDBYMODE/0.4W(100-130VAC)/0.5W(200-240VAC)inPOWER-SAVINGModeforSTANDBYMODE

MechanicalInstallation Orientation:Desktop/Front,Desktop/Rear,Ceiling/Front,Ceiling/RearDimensions 15.7"(W)×5.9"(H)×14.1"(D) 399mm(W)×150.5mm(H)×358mm(D) (notincludingprotrusions)Weight 16.3lbs/7.4kgEnvironmentalConsiderationsOperationalTemperatures: 41°to104°F/5°to40°C, (Ecomodeselectedautomaticallyat95°to104°F/35°to40°C),20%to

80%humidity(non-condensing)StorageTemperatures: 14°to122°F(−10°to50°C),20%to80%humidity (non-condensing)Regulations UL/C-ULApproved(UL60950-1,CSA60950-1) MeetsDOCCanadaClassBrequirements MeetsFCCClassBrequirements MeetsAS/NZSCISPR.22ClassB MeetsEMCDirective(EN55022,EN55024,EN61000-3-2,EN61000-3-3) MeetsLowVoltageDirective(EN60950-1,TÜVGSApproved)

Foradditionalinformationvisit:US:http://www.necdisplay.com/Europe:http://www.nec-display-solutions.com/Global:http://www.nec-display.com/global/index.htmlForinformationonouroptionalaccessories,visitourwebsiteorseeourbrochure.Thespecificationsaresubjecttochangewithoutnotice.

http://www.necdisplay.com/

http://www.nec-display-solutions.com/

http://www.nec-display.com/global/index.html

91

8. Appendix

Cabinet Dimensions

スーム

150.5/5.9"

358/14.1"

4.7/0.19"

168.3/6.63"

399/15.7"

Unit:mm/inch

92

Screen Size and Projection DistanceThissectionshouldbeusedwhenconsideringthedistancetothescreenandthescreensize.Thefollowingisanexampleofwhenthestandardlensisused.

[NP3200/NP2200/NP1200]Availableprojectiondistancesare1.0m/41.2inchesfor30"screento18m/718inchesfor500"screen,accordingto the chart.

UsingtheChartExamplefor100"screen:Theprojectiondistanceisapproximately3.1m(122")accordingtotheupperchart.Thelowerchartshowsthattheverticaldistancebetweentheprojectorfootandthescreentopisapproximately1.5m(59").Theprojectionanglecanbeadjustedupto10°.(Thelowerchartshowsthattheprojector isplacedinahorizontalposition)

4030

60

80

100

120

150

200

240

(Model)

300

400

500

Screen size(Diagonal)

Wide

Tele

Throw distance

Vertical lens shift : the highest position

2 4 14 16 18 20 22121086 (m)

2 4 14 16 18 20 22121086 (m)

When tilted at an angle 10 in Wide

Wide Tele

Screen center line (Wide)

Screen center line (Tele)

Projector foot

2

0

4

6

8

10(m)

Vertical distance between projector foot and screen

top

8. Appendix

93

ListofScreenSizes

[NP3200/NP2200/NP1200]

NOTE: The values in the tables are design values and may vary.

ScreenSizeandProjectionDistanceforDesktopwhenthestandardlensisusedThefollowingdrawingshowsanexampleforuseofDesktop.Horizontalprojectionposition:LenscenteredlefttorightVerticalprojectionposition:Seethetablebelow.

88 mm/3.47"Projector foot

H1

H2

Lens centerL

Screen centerH2 = Screen height (V) - H1

Screen bottom

Width

Screen size (Diagonal)Height

List of Screen Sizes

Formulas: Screen width H (m)=Screen size x 4/5 x 0.0254 Screen height V (m)=Screen size x 3/5 x 0.0254 Screen width H (inch)=Screen size x 4/5 Screen height V (inch)=Screen size x 3/5

Screen size Width (H) Height (V) m inch m inch 30" 0.6 24.0 0.46 18.0 40" 0.8 31.5 0.6 23.6 60" 1.2 47.2 0.9 35.4 80" 1.6 63.0 1.2 47.2 100" 2.0 78.7 1.5 59.1 120" 2.4 94.5 1.8 70.9 150" 3.0 118.1 2.3 90.6 200" 4.1 161.4 3.0 118.1 250" 5.1 200.8 3.8 149.6 300" 6.1 240.2 4.6 181.1 400" 8.1 318.9 6.1 240.2 500" 10.2 401.6 7.6 299.2

STANDARD Screen size Projection Distance (L) (H1) (diagonal) (m) (inches) Wide - Tele Wide - Tele (cm) (inches) 30" 0.89 - 1.20 35.1 - 47.3 0-23 0-9.0 40" 1.20 - 1.62 47.4 - 63.8 0-30 0-12.0 60" 1.83 - 2.45 72.2 - 96.6 0-46 0-18.0 67" 2.05 - 2.75 80.8 - 108.2 0-51 0-20.1 72" 2.21 - 2.96 87.0 - 116.4 0-55 0-21.6 80" 2.46 - 3.29 96.9 - 129.5 0-61 0-24.0 84" 2.59 - 3.46 101.8 - 136.1 0-64 0-25.2 90" 2.78 - 3.71 109.3 - 146.0 0-69 0-27.0 100" 3.09 - 4.13 121.6 - 162.4 0-76 0-30.0 120" 3.72 - 4.96 146.3 - 195.3 0-91 0-36.0 150" 4.66 - 6.21 183.4 - 244.6 0-114 0-45.0 180" 5.60 - 7.47 220.5 - 294.0 0-137 0-54.0 200" 6.23 - 8.30 245.3 - 326.9 0-152 0-60.0 210" 6.54 - 8.72 257.6 - 343.3 0-160 0-63.0 240" 7.49 - 9.97 294.7 - 392.6 0-183 0-72.0 250" 7.80 - 10.39 307.1 - 409.1 0-191 0-75.0 270" 8.43 - 11.23 331.8 - 442.0 0-206 0-81.0 300" 9.37 - 12.48 368.9 - 491.3 0-229 0-90.0 400" 12.51 - 16.66 492.5 - 655.8 0-305 0-120.0 500" 15.65 - 20.83 616.2 - 820.2 0-381 0-150.0

8. Appendix

94

Mini D-Sub 15 Pin Connector Pin Assignments of D-Sub COMPUTER 1 Input Connector

SignalLevelVideosignal:0.7Vp-p(Analog)Syncsignal:TTLlevel1115 1214 13

65 4 3 2 1

10 79 8

8. Appendix

PinNo. RGBSignal(Analog) YCbCrSignal

1 Red Cr

2 GreenorSynconGreen Y

3 Blue Cb

4 Ground

5 Ground

6 RedGround CrGround

7 GreenGround YGround

8 BlueGround CbGround

9 NoConnection

10 SyncSignalGround

11 NoConnection

12 Bi-directionalDATA(SDA)

13 HorizontalSyncorCompositeSync

14 VerticalSync

15 DataClock

95

8. Appendix

Compatible Input Signal List

Horizontal:15KHzto100KHz(RGB:24KHzorover)Vertical:50Hzto120Hz

SignalResolution(Dots)

FrequencyH.(kHz)

RefreshRate(Hz)

VIDEO NTSC - * 15.73 59.94PAL - * 15.63 50.00PAL60 - * 15.73 60.00SECAM - * 15.63 50.00

IBMcompatible 640 × 480 31.47 59.94640 × 480 31.48 59.95640 × 480 37.86 72.81640 × 480 37.50 75.00640 × 480 39.38 75.00640 × 480 43.27 85.01800 × 600 35.16 56.25800 × 600 37.88 60.32800 × 600 48.08 72.19800 × 600 46.88 75.00800 × 600 53.67 85.06

1024 × 768 48.36 60.001024 × 768 56.48 70.071024 × 768 60.02 75.031024 × 768 68.68 85.001152 × 864 54.35 60.051152 × 864 63.99 70.021152 × 864 67.50 75.001152 × 864 * 77.49 85.061280 × 768 47.78 59.871280 × 800 49.70 59.811280 × 960 60.00 60.001280 × 960 * 75.00 75.001280 × 960 * 85.94 85.001280 × 1024 63.98 60.021280 × 1024 * 79.98 75.021280 × 1024 * 91.15 85.021400 × 1050 64.74 59.951400 × 1050 * 65.32 59.981440 × 900 * 55.94 59.891600 × 1200 * 75.00 60.001600 × 1200 * 81.25 65.001600 × 1200 * 87.50 70.001600 × 1200 * 93.75 75.00

AppleMacintosh® 640 × 480 35.00 66.67832 × 624 49.72 74.55

1024 × 768 60.24 74.931152 × 870 68.68 75.061280 × 1024 64.30 60.381280 × 1024 * 69.87 65.181280 × 1024 * 78.44 73.72

HDTV (1080i/60) 1920 × 1080 33.75 60.00(1080i/50) 1920 × 1080 28.13 50.00(720p/60) 1280 × 720 45.00 60.00

SDTV 480p 720 × 480 31.47 59.94DVD YCbCr 720 × 480 * 15.73 59.94

720 × 576 * 15.63 50.00Progressive 720 × 480 31.47 59.94

720 × 576 31.25 50.00

NOTE:• Imagesaboveflaggedwith“*”arenotsupportedbydigitalsignal.• Animagewithhigherresolutionthantheprojector’snativeresolution(1024x768)willbedisplayedwithAdvancedAccuBlend.• Somecompositesyncsignalsmaynotbedisplayedcorrectly. Signals other than those specified in the table above may not be displayed correctly. If this should happen, change the refresh

rate or resolution on your PC. Refer to Display Properties help section of your PC for procedures.

96

8. Appendix

7 PC Control Codes and Cable ConnectionPC Control Codes

Function Code DataPOWER ON 02H 00H 00H 00H 00H 02HPOWER OFF 02H 01H 00H 00H 00H 03HINPUT SELECT COMPUTER 1 02H 03H 00H 00H 02H 01H 01H 09HINPUT SELECT COMPUTER 2 02H 03H 00H 00H 02H 01H 02H 0AHINPUT SELECT COMPUTER 3 02H 03H 00H 00H 02H 01H 1AH 22HINPUT SELECT VIDEO 02H 03H 00H 00H 02H 01H 06H 0EHINPUT SELECT S-VIDEO 02H 03H 00H 00H 02H 01H 0BH 13HPICTURE MUTE ON 02H 10H 00H 00H 00H 12HPICTURE MUTE OFF 02H 11H 00H 00H 00H 13HSOUND MUTE ON 02H 12H 00H 00H 00H 14HSOUND MUTE OFF 02H 13H 00H 00H 00H 15H

NOTE: Contact your local dealer for a full list of PC Control Codes if needed.

97

8. Appendix

NOTE1:Pins1,4,6and9arenotused.

NOTE2:Jumper“RequesttoSend”and“CleartoSend”togetheronbothendsofthecabletosimplifycableconnection.

NOTE 3: For long cable runs it is recommended to set communication speed within projector menus to 9600 bps.

1 52 43

6 7 98

ToGNDofPC

ToRxDofPC

ToTxDofPC

ToRTSofPC

ToCTSofPC

PC Control Connector (D-SUB 9P)

Cable ConnectionCommunicationProtocol

Baud rate �� 19200 bpsData length �� 8 bitsParity �� No parityStop bit �� One bitX on/off �� NoneCommunications procedure �� Full duplex

NOTE:Dependingontheequipment,alowerbaudratemayberecommendedforlongcableruns.

98

8 Troubleshooting Check ListBeforecontactingyourdealerorservicepersonnel,checkthefollowinglisttobesurerepairsareneededalsobyreferringtothe“Troubleshooting”sectioninyouruser’smanual.Thischecklistbelowwillhelpussolveyourproblemmoreefficiently.*Printthispageandthenextpageforyourcheck.

8. Appendix

No image is displayed from your PC or video equipment to the projector�

Still no image even though you connect the projector to the PC first, then start the PC�Enabling your notebook PC’s signal output to the projector�• Acombinationoffunctionkeyswillenable/disabletheexternaldisplay.Usually,thecombinationofthe“Fn”keyalong with one of the 12 function keys turns the external display on or off.

No image (blue or black background, no display)�Still no image even though you press the AUTO ADJUST button�Still no image even though you carry out [RESET] in the projector’s menu�Signal cable’s plug is fully inserted into the input connectorA message appears on the screen�( _____________________________________________ )The source connected to the projector is active and available�Still no image even though you adjust the brightness and/or the contrast�Input source’s resolution and frequency are supported by the projector�

Frequency of occurrence always sometimes (How often?_____________________) other (__________________)Power

No power (POWER indicator does not light green) See also “Status Indicator (STATUS)”�

Power cable’s plug is fully inserted into the wall outlet�Main power switch is pressed to the ON position�Lamp cover is installed correctly �Lamp Hours Used (lamp operation hours) was cleared after lamp replacement�No power even though you press and hold the POWER but-ton for 1 second�

Shut down during operation�Power cable’s plug is fully inserted into the wall outlet�Lamp cover is installed correctly �[AUTO POWER OFF] is turned off (only models with the [AUTO POWER OFF] function)�[OFF TIMER] is turned off (only models with the [OFF TIMER] function)�

Video and Audio

Image is too dark�Remains unchanged even though you adjust the brightness and/or the contrast�

Image is distorted�Image appears to be trapezoidal (unchanged even though you carry out the [KEYSTONE] adjustment)�

Parts of the image are lost�Still unchanged even though you press the AUTO ADJUST button�Still unchanged even though you carry out [RESET] in the projector’s menu�

Image is shifted in the vertical or horizontal direction�Horizontal and vertical positions are correctly adjusted on a computer signal�Input source’s resolution and frequency are supported by the projector�Some pixels are lost�

Image is flickering�Still unchanged even though you press the AUTO ADJUST button�Still unchanged even though you carry out [RESET] in the projector’s menu�Image shows flickering or color drift on a computer signal�Still unchanged even though you change [FAN MODE] from [HIGH ALTITUDE] to [AUTO]�

Image appears blurry or out of focus�Still unchanged even though you checked the signal’s resolu-tion on PC and changed it to projector’s native resolution�Still unchanged even though you adjusted the focus�

No sound�Audio cable is correctly connected to the audio input of the projector�Still unchanged even though you adjusted the volume level�AUDIO OUT is connected to your audio equipment (only models with the AUDIO OUT connector)�

OtherRemote control does not work�

No obstacles between the sensor of the projector and the remote control�Projector is placed near a fluorescent light that can disturb the infrared remote controls�Batteries are new and are not reversed in installation�

Buttons on the projector cabinet do not work (only models with the [CONTROL PANEL LOCK] function)

[CONTROL PANEL LOCK] is not turned on or is disabled in the menu�Still unchanged even though you press and hold the EXIT button for a minimum of 10 seconds�

99

In the space below please describe your problem in detail.

Information on application and environment where your projector is used

Projector

Model number:Serial No�:Date of purchase:Lamp operating time (hours):Eco Mode: Off OnInformation on input signal:

Horizontal synch frequency [ ] kHzVertical synch frequency [ ] HzSynch polarity H (+) (−) V (+) (−)Synch type Separate Composite

Sync on GreenSTATUS Indicator:

Steady light Orange GreenFlashing light [ ] cycles

Remote control model number:

Signalcable

NEC standard or other manufacturer’s cable?Model number: Length: inch/m

Distribution amplifierModel number:

SwitcherModel number:

AdapterModel number:

Projector PC

DVDplayer

Installation environment

Screen size: inchScreen type: White matte Beads Polarization Wide angle High contrastThrow distance: feet/inch/mOrientation: Ceiling mount DesktopPower outlet connection:

Connected directly to wall outlet Connected to power cord extender or other (the

number of connected equipment______________) Connected to a power cord reel or other (the num-

ber of connected equipment______________)

Computer

Manufacturer:

Model number:

Notebook PC / Desktop

Native resolution:

Refresh rate:

Video adapter:

Other:

Video equipment

VCR, DVD player, Video camera, Video game or other

Manufacturer:

Model number:

8. Appendix

100

8. Appendix

9 TravelCare GuideTravelCare - a service for international travelersThis product is eligible for “TravelCare”,NEC’s unique internationalwarranty.Pleasenote thatTravelCare coveragediffers in part fromcoverageunderthewarrantyincludedwiththeproduct.

Services offered with TravelCareThiswarrantyallowscustomerstoreceiveserviceontheirproductattheNECandNEC-designatedservicestationsinthecountrieslistedhereinwhentemporarilytravelinginternationallyforbusinessorplea-sure.Fordetailsonservicesofferedbythedifferentservicestations,pleaserefertothe“ListofTravelCareOutlets”below.

1 Repair servicesTheproductwillberepairedanddeliveredwithin10businessdays,notincludingshippingtime.During the termofwarranty, thecostofmaintenanceparts, laborcostsforrepairsandshippingcostswithintheservicestation’scov-erageareaarecoveredbythewarranty.

2 Replacement product rental serviceIfthecustomerdesires,heorshecanrentareplacementproductwhiletheoriginalproductisbeingrepaired.Fee:US$200for12daysThisfeemustbepaidatthelocalservicestationincashorcreditcard. TheUS$200rentalfeeisnon-refundableevenifthecustomerrentsitlessthan12daysbeforereturning.Thereplacementproductwillbedeliveredwithin3businessdays.If the customer did not return the replacement productwithin 12days,thecustomerwillbechargedthepriceoftheunit.If the customer returned the replacement product in a faulty ordamagedcondition,therepaircostwillbechargedtothecustomer.Note that this service is not offered in all countries and regions.Pleaserefertothe“ListofTravelCareOutlets”.In addition, this replacement product rental service is not offeredaftertheproduct’swarrantyhasexpired.

Term of warranty1

a. Uponpresentationof thewarranty or receipt receiveduponpurchase:

Validforthetermindicatedonthewarrantyorthenormaltermofwarrantyforthecountryofpurchase.

b. Whenonlytheproductisbroughtin:

Validforaperiodofwithin14monthsofthedateofmanufac-tureindicatedbytheserialnumberattachedtotheproduct.

2 Whenaproductwhosetermofwarrantyisexpiredisbroughtin:

Repairswill beoffered for a fee. In this case the customer is noteligibleforthereplacementproductrentalservice.

3 Inthefollowingcases,repairsmaybecharged,eveniftheproduct’swarrantyisstillineffect:

1) Ifthetermofwarranty,modelname,serialnumberandnameof thestoreofpurchasearenot indicatedon thewarrantyorhavebeenaltered.

2) Problemsor damagecausedbydroppingor shocksduringshipment ormovement by the customer or by improper han-dlingbythecustomers.

3) Problemsordamagecausedbyimproperusageorunwarrant-ablealterationsorrepairsbythecustomer.

4) Problems or damage caused by fire, salt damage, gasdam-age,earthquakes,lightningdamage,stormorflooddamageorothernaturaldisastersorsuchexternal factorsasdust,ciga-rettesmoke,abnormalvoltage,etc.

5) Problemsordamagecausedbyuseinhotorhumidplaces,invehicles,boatsorships,etc.

6) Problems or damage caused byexpendable supplies or de-vicesconnectedtotheproductotherthanthosedesignatedbyNEC.

7) Problemscausedbynatural consumption,wear or deteriora-tionofpartsundernormalusageconditions.

8) Problemsordamagetolampsandotherexpendablesupplies,includedpartsoroptionalparts.

9) Other conditions stipulated in thewarranty includedwith theproductalsoapply.

NOTE: The product can be used overseas with voltages indicated in the rat-ing label on the product by using a power cable suited for the standards and power source voltage of the country in which the product is being used.

List of TravelCare Outlets

ThislistappliesasofJuly1,2009.Forthemostup-to-dateinformation,pleaserefertothewebsitesoftheservicestationsinthevariouscountriesontheListofTravelCareOutletsortotheNECwebsiteathttp://www.nec-display.com/global/index.html

In EuropeNECEuropeLtd./EuropeanTechnicalCentreAddress: UnitG,StaffordPark12,TelfordTF33BJ,U.K.Telephone: +441952237000FaxLine: +441952237006EmailAddress: [email protected]: http://www.neceur.com

(RegionsCovered)EU: Austria*,Belgium*,Bulgaria*,CzechRepublic*,Cyprus*,

Denmark*,Estonia*,Finland*,France*,Germany*,Greece*,Hungary*,Ireland*,Italy*,Latvia*,Lithuania*,Luxembourg*,Malta*,TheNetherlands*,Poland*,Portu-gal*,Romania*,Slovakia*,Slovenia*,Spain*,Sweden*andtheUnitedKingdom*

EEA: Norway*,IcelandandLiechtenstein

In North AmericaNECDisplaySolutionsofAmerica,Inc.Address: 500ParkBoulevard,Suite1100Itasca,Illinois

60143,U.S.A.Telephone: +18008360655FaxLine: +18003562415EmailAddress: [email protected]: http://www.necdisplay.com/

(RegionsCovered)U.S.A.*,Canada*

In OceaniaAWALimited.Address: 151ArthurStreet HomebushWestNSW2140AustraliaCustomerCallCentreTelephone: 0297647777FaxLine: 1300772688EmailAddress: [email protected]

ForTravelCareservice,whilecustomerisinAustralia,thecus-tomerwillcontactAWAon1300366144,selectOption4.Ifyouwanttobookwarrantyservicebyemailcustomergoesto:[email protected].

(RegionsCovered)Australia

NOTE: In countries designated with an asterisk(*), replacement product rental

service are offered.



http://www.neceur.com

http://www.necdisplay.com/

101

8. Appendix

NECCorporationofMalaysiaSdn.Bhd.Address: 33rdFloor,MenaraTAOne,22,JalanP.Ram-

lee,50250KualaLumpur,MalaysiaTelephone: +60321783600(ISDN)FaxLine: +60321783789EmailAddress: [email protected]: http://www.necarecenter.com

(RegionsCovered)Malaysia

HyosungITXCo.,Ltd.Address: 1stFl.,IreB/D.#2,4Ga,Yangpyeng-Dong,

Youngdeungpo-Gu,Seoul,Korea150-967Telephone: +82221634193FaxLine: +82221634196EmailAddress: [email protected]

(RegionsCovered)SouthKorea

LensoCommunicationCo.,Ltd.Address: 292LensoHouse4,1stFloor,Srinakarin

Road,Huamark,Bangkapi,Bangkok10240,Thailand

Telephone: +6623752425FaxLine: +6623752434EmailAddress: [email protected]: http://www.lensocom.com/

(RegionsCovered)Thailand

e-flexL.L.C.Address: AlSuwaidiRoad,Rashidiya43500Dubai

UnitedArabEmiratesTelephone: +97142861533FaxLine: +97142861544EmailAddress: [email protected]

(RegionsCovered)UnitedArabEmirates

SamirPhotographicSuppliesAddress: P.O.Box599,Jeddah21421,SaudiArabiaTelephone: +96626828219FaxLine: +96626830820EmailAddress: [email protected]

(RegionsCovered)SaudiArabia

NOTE: In countries designated with an asterisk(*), replacement product rental

service are offered.

VisualGroupLtd.Address: 28WallsRoadPenroseAucklandNewZealandTelephone: 095250740FaxLine: 095809607EmailAddress: [email protected]

(RegionsCovered)NewZealand

In Asia and Middle EastNECDisplaySolutions,Ltd.Address: 686-1,Nishioi,Oi-Machi,Ashigarakami-Gun,

Kanagawa258-0017,JapanTelephone: +81465852369FaxLine: +81465852393EmailAddress: [email protected]: http://www.nec-pj.com

(RegionsCovered)Japan*

NECSolutions(China)Co.,Ltd.Address: Rm1903,ShiningBuilding,35XueyuanRd, HaidianDistrictBeijing100083,P.R.C.Telephone: +861082317788FaxLine: +861082331722EmailAddress: [email protected] [email protected]: http://www.necsl.com.cn

(RegionsCovered)China

NECHongKongLtd.Address: 25/F.,TheMetropolisTower,10Metropolis

Drive,Hunghom,Kowloon,HongKongTelephone: +85223690335FaxLine: +85227956618EmailAddress: [email protected] [email protected]: http://www.nec.com.hk

(RegionsCovered)HongKong

NECTaiwanLtd.Address: 7F,No.167,SEC.2,NanKingEastRoad,

Taipei,Taiwan,R.O.C.Telephone: +886285001700FaxLine: +886285001420EmailAddress: [email protected]: http://www.nec.com.tw

(RegionsCovered)Taiwan

NECAsiaPte.Ltd.Address: 401CommonwealthDrive,#07-02,HawPar

Technocentre,Singapore149598Telephone: +6562738333FaxLine: +6562742226EmailAddress: [email protected]: http://www.nec.com.sg/home.php

(RegionsCovered)Singapore

http://www.necarecenter.com

http://www.lensocom.com/

http://www.nec-pj.com

http://www.necsl.com.cn

http://www.nec.com.hk

http://www.nec.com.tw

http://www.nec.com.sg/home.php

102

8. Appendix

TO:NECorNEC’sAuthorizedServiceStation:FM:

(Company&Namewithsignature)

DearSir(s),

IwouldliketoapplyyourTravelCareServiceProgrambasedonattachedregistrationandqualificationsheetandagreewith

yourfollowingconditions,andalsotheServicefeewillbechargedtomycreditcardaccount,ifIdon’treturntheLoanunits

withinthespecifiedperiod.Ialsoconfirmfollowinginformationiscorrect.Regards.

Application Sheet for TravelCare Service Program

P-1/,

Country,

productpurchased:

User’sCompanyName:

User’sCompanyAddress:

PhoneNo.,FaxNo.:

User’sName:

User’sAddress:

PhoneNo.,FaxNo.:

LocalContactoffice:

LocalContactofficeAddress:

PhoneNo.,FaxNo.:

User’sModelName:

DateofPurchase:

SerialNo.oncabinet:

ProblemofunitsperUser:

RequiredService: (1)RepairandReturn (2)Loanunit

RequestedperiodofLoanunit:

Paymentmethod: (1)CreditCard (2)TravelersCheque (3)Cash

InCaseofCreditCard:

CardNo.w/ValidDate:

Date://,

103

8. Appendix

5.LoanServiceChargesandConditions:UponacceptanceofthisNECProjector,Customeragreestoassumeliabilityforthisloanunit.

Thecurrentcostofuseofthisloanunitis$200.00USDfor12calen-dardays.IfCustomerdoesnotreturntheunitwithinthe12calendardays,Cus-tomerwillbechargedthenexthighestcostuptoandincludingthefulllistpricetoCreditCards,whichpricewillbeinformedbyNECAutho-rizedServiceStations.Pleaseseetheattachedlistingofcontactsforeachcountrytoarrangeforpickupoftheloanunit.

If you return to their countryof originwith the loanunit, youwill bechargedadditionalfreighttoreturntheunittotheloaningcountry.

Thankyouforyourunderstandingofthisprogram.

Condition of your TravelCare Service ProgramEnduserisrequestedtounderstandfollowingconditionofTravelCareServiceProgramandcompletethenecessaryinformationontheap-plicationsheet.

1. Service Options:Thereare3 typesof“Service”available.Enduserhas tounderstandfollowingconditionandisrequiredtofillintheApplicationSheet.

1)RepairandReturn:

The ’Faulty unit’ is sent or collected from the customer. It is re-pairedand returnedwithin 10days to the customer, excludingtransporttime.

Theremayhaveacase, repairand returncan’tbedonebyNECAuthorizedServiceStation,becauseofshortageofsparepartsduetosamemodelisnotsoldintheterritory.

2)RepairandReturnwithLoan:(ThisserviceislimitedtosomeSer-viceStations)

Thisservice isoffered to theEnduser,whocannotwaituntil theirunitisrepaired.

Thecustomercanborrowaunitfor$200upto12days.Customerthen sends in inoperableunit to nearestNECAuthorizedServiceStationforservice.Inordertopreventcollectionproblem,EnduserisrequiredtofillinApplicationSheet.

EnduserneedstoconfirmtheavailabilityoftheServicetoNECAu-thorizedServiceStations.

3)LoanOnly:

Forthisservice,NECAuthorizedServiceStationsuppliesthecus-tomerwithaloanunitforUS$200upto12days.Customerkeepsthe inoperable unit andwhen customer returnshome, customerarrangestohavetheprojectorservicedinthehomecountry.

2. Warranty Exclusions:ThisprogramdoesnotapplyiftheProjector’sserialnumberhasbeendefaced,modifiedorremoved.If,inthejudgementofNECAuthorizedServiceStationoritsagentthedefectsorfailuresresultfromanycauseotherthanfairwearandtearorNECneglect,orfaultincludingthefollowingwithoutlimitation:

1)Accidents, transportation, neglect,misuse, abuse,water, dust,smokeordefaultoforbytheCustomeritsemployeesoragentsoranythirdparty;

2)Failureorfluctuationofelectricalpower,electricalcircuitry,aircon-ditioning, humidity control or other environmental conditions suchasuseitinsmokingarea;

3)Anyfaultintheattachmentsorassociatedproductsorcomponents(whetherornotsuppliedbyNECor itsagentswhichdonot formpartoftheProductcoveredbythiswarranty);

4)AnyactofGod,fire,flood,war,actofviolenceoranysimilaroccur-rence;

5)Anyattempt byanypersonother thananypersonauthorizedbyNECtoadjust,modify,repair,installorservicetheproduct.

6)AnyCross-borderchargessuchas,duty,insurance,taxetc.

3.ChargesforWarrantyExclusionsandOutofWarrantyCase:Incasefaultyunit isunderwarrantyexclusionscaseorunderOutofWarrantyperiod,NECAuthorizedServiceStationwill Informestima-tionofactualservicecosttotheEnduserwithreason.

4.DeadonArrival(DOA):Endusermust take this issueupwith their original supplier in thecountryofpurchase.NECAuthorizedServiceStationwill repair theDOAunit asaWar-rantyrepair,butwillnotexchangeDOAunitwithnewunits.

lcd projector np3200/np2200/np1200 - nec · pdf filelcd projector np3200/np2200/np1200 ......

Documents