led upgrade kit installation guide - · pdf filefixture: pros - providence small ... steps: to...

LED Upgrade Kit Installation GuideFixture: PROS - Providence Small

A R C H I T E C T U R A L A R E A L I G H T I N G93065348 REV A

PAGE 1/5

TM

www.aal.net

16555 East Gale AvenueCity of Industry, CA 91745626.968.5666

6 3 A74011 DISCT3M MNI 14-250DFI AS NOTED

5 2 A84337 WSHR-No. 10 SPLIT LK SS

4 2 A84252 SCR-10-24x3/4 PHH PHMS SS

3 AS NOTED 93035846 CONN-WAGO 2-WIRE 222-412

2 1 - LED DRIVER STRAP ASSEMBLY

1 1 - LED RETRO-FIT OPTICAL ASSEMBLY

ITEM # QTY PART # DESCRIPTION NOTES

UPGRADE KIT CONTENTS

2

1

3

4

5

WARNING: Fixtures must be grounded in accordance with local codes or the National Electrical Code. Failure to do so may result in serious personal injury.

MAINTENANCE: A regularly scheduled maintenance program should be established to retain optimum lightoutput and reduce heat retention. Dusting with a soft, clean, dry cloth is normally sufficient for the optics.

CAUTION: All wiring must be done by a qualified electrician. KEEP THIS SHEET FOR FUTURE REFERENCE.

Examine all parts that are not intended to be replaced by the retrofit kit for damage and replace any damageparts prior to installation of the retrofit.

!

ADD 4 MORE FORTRA59D / WMA59D

ARM OPTIONS ONLY

FOR TRA59U / WMA59UARM OPTIONS ONLY

6



PAGE 2/5

TM

www.aal.net


STEPS: TO DIS-ASSEMBLE EXISTING ASSEMBLY:

1. Pull latch (as shown on the illustration) unplug all connectors, remove guts and discard.

2. Rotate fitter cap counter clockwise, until free from fixture (See fitter cap detail) unplug all connectors, remove guts and discard.

TURN OFF ALL POWER TO THE UNIT AND TAKE PROPER SAFETY PRECAUTIONS. FAILURE TODO SO MAY RESULT IN SERIOUS PERSONAL INJURY.!

PROSPOST TOP/TRA59U/WMA59U

UPWARD OPTIONS

PROSTRA59D/WMA59D

DOWNWARD OPTIONS

LATCH

FITTER CAP

TABS

LATCH

FITTER CAP

TABS

CLOSED OPEN

FITTER CAP DETAIL

BALLAST(REF)

G12 LAMP(REF)

G12 LAMP(REF)

BALLAST (REF)



PAGE 3/5

TM

www.aal.net


STEPS: TO RETROFIT LED

1. Remove existing screws on each side as shown in location "A" and "B", assemble LED retro-fit optical assembly with new produced two washers and two 10-24 x 3/4" screws provided by A.A.L. as shown on the illustrations below.

2. To assemble LED driver strap assembly, remove existing two 10-24 screws and assemble LED driver strap assembly to fitter cap with same hardware as shown in the illustration below.

3. For wiring diagrams:POST TOP MOUNT / TRA59U ARM / WMA59U ARM (UPWARD OPTIONS) see page 4.TRA59D ARM / WMA59D ARM (DOWNWARD OPTIONS) see page 5.

4. Close top dome by snapping latch securely to bottom dome assembly, Place LED driver assembly carefully inside fitter cap assembly rotate fitter cap clockwise until tabs snap securely into fitter.

5. Retrofit installation complete.

ITEM#1LED RETRO-FIT

OPTICAL ASSEMBLY

ITEM#42X A84252SCR-10-24x3/4" PHH PHMS SS

ITEM#52X A84337WSHR-N0. 10 SPLIT LK SS

DRAWING SHOWNUPWARD OPTIONS

POST TOP MOUNT/TRA59U/WMA59U(REFERENCE)

ITEM#2LED DRIVER STRAP ASSEMBLY

EXISTING2X SCR-10-24X5/8 HARDWARE

FITTER CAP

TABS

LATCH

TOP DOMEASSEMBLY

LOCATION "A"

LOCATION "B'

BOTTOM DOME ASSEMBLY



PAGE 4/5

TM

www.aal.net


WIRING DIAGRAMPOST TOP MOUNT/TRA59U/WMA59UUPWARD OPTIONS

WMA59U ARMOPTION

TRA59U ARMOPTION

POST TOP MOUNTOPTION

POLE(REF)

BOND TOBOTTOM DOME

BOND TOFITTER

GROUND TOFITTER

BOND TOTOP DOME

ITEM#35X 93035846CONN-WAGO 2-WIRE 222-412

LEAD WIRES

5 CABLECONDUCTOR

YELLOW/GREEN

BLUEGRAY

BLACK

BROWNYELLOW/GREEN

BR

OW

N

GR

AY

BLA

CK

BLU

E

YELLOW (+)

BROWN (-)

GREEN

OS

RA

M O

PTO

TRO

NIC

OT5

0W/U

NV

GRAY (-)

WHITE (+)

GR

EE

N

PU

RP

LEG

RA

Y

BLA

CK

WH

ITE

BLA

CK

WH

ITE

BLU

ER

ED

OR

AN

GE



PAGE 5/5

TM

www.aal.net


WMA59D ARMOPTION

TRA59D ARMOPTION

POLE(REF)

LEADWIRES

5 CABLECONDUCTOR

YELLOW/GREEN

BLUE

GRAY

BLACKBROWN

YELLOW/GREEN

BLU

E

OR

AN

GE

PU

RP

LE

BR

OW

N

GR

AY

BLA

CK

BLU

E

YELLOW (+)

BROWN (-)

GREEN

OS

RA

M O

PTO

TRO

NIC

OT5

0W/U

NV

GR

AY

RE

D

GRAY (-)

WHITE (+)

BLACK

WHITE

GREEN

BLA

CK

WH

ITE

5 CABLECONDUCTOR

GRAY

BLUE

BLU

EG

RA

Y

BOND TOBOTTOM DOME

BOND TOTOP DOME

BOND TOFITTER

ITEM#39X CONN-WAGO 2-WIRE 222-412

NOTE:USE TWO WIRESFOR DIMMING OPTIONAL

GROUND TOTOP DOME

WIRING DIAGRAMTRA59D ARM / WMA59D ARMDOWNWARD OPTIONS(WITH TWO 5 CABLE CONDUCTOR)

INSTALLATION INSTRUCTIONSCATALOG NUMBER

PART NO.APPRVDDATE

DATE REV.

14249 Artesia Blvd. P.O. Box 1869La Mirada, CA 90638-1869

(714)994-2700 fax(714)994-0522 A96482

PROS IND

WARNING: THIS PRODUCT CONTAINS CHEMICALS KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER, BIRTH DEFECTS, AND/OR OTHERREPRODUCTIVE HARM. THOROUGHLY WASH HANDS AFTER INSTALLING, HANDLING, CLEANING OR OTHERWISE TOUCHING THIS PRODUCT.

DOME

LATCH

INCOMINGWIRE LEADS

3.

2.

6.

5.4.

1.2.

5.

OPEN

1.2.

3.SUPPLY.

6.

1.

3.

4.

LAMP (REFERENCE)

FITTER CAP

BALLAST

LAMP SERVICING:TURN POWER OFF.

LATCH SECURELY.

TO RELEASE BALLAST,

BALLAST SERVICING:TURN POWER OFF.

SERVICE BALLAST.

3" O.D. POLE (REF)

WIRE CONNECTIONS(BY OTHERS)

8-32 X 1/4"

(2) P/N A84031PHMS S/S

(3) P/N 93007472SET SCREW S/S5/16-18 X 1/4"

TURN OFF POWER.INSTALLATION STEPS:

CLOSED

(BY OTHERS)

CONNECTORS

CAREFULLY PLACE FITTER CAP INTO FITTER,

LAMP SERVICING COMPLETE.SNAP SECURELY INTO FITTER.ROTATE FITTER CAP CLOCKWISE UNTIL TABS

PLUG IN ALL CONNECTORS, RE-INSTALL BALLAST

UNPLUG ALL CONNECTORS AND REMOVE (2) SCREWS

AND SECURE WITH (2) SCREWS. CLOSE DOME AND

BALLAST SERVICING COMPLETE.

LIFT FITTER CAP WITH REFLECTOR FROM FITTER.

ROTATE FITTER CAP COUNTER CLOCKWISE, UNTILFREE FROM FIXTURE. (SEE FITTER CAP DETAIL)

PULL LATCH AND RAISE DOME TO ACCESS BALLAST.

BE GROUNDED TO THE INCOMING EQUIPMENT GROUND

WITH (3) 5/16-18 x 1/4" SET SCREWS.INSTALLATION COMPLETE.

MAKE WIRE CONNECTIONS FROM INCOMING WIRE LEADS

FITTER CAP DETAIL

TO ARM LEADS, AS SHOWN. (WHITE TO COMMON, BLACK4. INSTALL LAMP (BY OTHERS).

FIXTURE

SLIP FIXTURE OVER POLE, AND SECURE FIXTURE TO POLE

TO HOT AND GREEN TO GROUND). NOTE: ASSEMBLY MUST

TABS

1 2

2

1


PART NO.APPRVDDATE

DATE REV.


(714)994-2700 fax(714)994-0522 A96483

PROS IND


Date

TRA59U

CLOSED

ARM

1.

TENON

DOME

(BY OTHERS)

6.

5.

3.

1.2.

6.

4.

3.

5.

4.

2.1.

4.

5.

3.

BALLAST

LATCH

TURN POWER OFF.BALLAST SERVICING:

OPEN

MOUNTING PLATE(ORIENTATION)

WIRE CONNECTIONS

(HARDWARE AS NOTED).


TURN POWER OFF.LAMP SERVICING:

TO RELEASE BALLAST,

LATCH SECURELY.

FITTER CAP DETAIL

LAMP (REFERENCE)(BY OTHERS)

FITTER CAP

INCOMING WIRE LEADS

4" O.D. POLE (REF)

CAREFULLY PLACE FITTER CAP INTO FITTER,INSTALL LAMP (BY OTHERS).LIFT FITTER CAP FROM FITTER.

ROTATE FITTER CAP COUNTER CLOCKWISE, UNTIL

INSTALLATION COMPLETE.

3/8-16 X 1" LG

(2) P/N A84186SHCS S/S

LAMP SERVICING COMPLETE.

SNAP SECURELY INTO FITTER.

FREE FROM FIXTURE. (SEE FITTER CAP DETAIL)



SERVICE BALLAST ASSEMBLY.

AND SECURE WITH (2) SCREWS. CLOSE DOME AND


ROTATE FITTER CAP CLOCKWISE UNTIL TABS

5/16-18 X 1/4"

(3) P/N 93007472SET SCREW S/S

COMMON, BLACK TO HOT AND GREEN TO GROUND).NOTE: ASSEMBLY MUST BE GROUNDED TO THEINCOMING EQUIPMENT GROUND SUPPLY.PLACE WIRING IN POLE AND SECURE ARM TO POLE

SLIP FIXTURE OVER ARM, AND SECURE FIXTURETO ARM WITH (3) 5/16-18 x 1/4" SET SCREWS.

MOUNTING HARDWAREFOR POLE BY AAL,

FOR POLE BY OTHERS,

MAKE WIRE CONNECTIONS FROM INCOMING WIRE

HARDWARE BY OTHERS.

LEADS TO ARM LEADS, AS SHOWN. (WHITE TO

HARDWARE INCLUDED.

TABS

CONNECTORS

PHMS S/S8-32 X 1/4"

(2) P/N A84031

PULL LATCH AND RAISE DOME TO ACCESS BALLAST.2.

2

1

3

1 23

WIREWAY

2.50

10.0

(2) 7/16" CLEARANCE


PART NO.APPRVDDATE

DATE REV.


(714)994-2700 fax(714)994-0522 A96485

PROS DIR


TRA59D

(ORIENTATION)

SHCS S/S

CONNECTORS

4" O.D. POLE (REF)

INCOMINGWIRE LEADS

FIXTURE

FIXTUREFRONT OF

DOME

ARM

LATCH

CAPTIVE SCREWS

OPENCLOSED

CONNECTORS

1.

3.

4.

2.

6.

7.

5.

TURN POWER OFF.

3.

1.2.

LAMP SERVICING:

2.3.

4.

TURN OFF POWER.1.

CAPTIVESCREWS

BALLAST INTO FITTER.

SECURELY INTO FITTER.

BALLAST SERVICING:

LIFT FITTER CAP WITH BALLAST FROM FITTER AND


UNPLUG ALL CONNECTORS.


PULL LATCH AND LOWER FIXTURE, AS SHOWN.INSTALL LAMP (BY OTHERS). ANDCLOSE FIXTURE AND LATCH SECURELY.LAMP SERVICING COMPLETE.

DOME DETAIL

MOUNTING PATTERN

5.

6.

3/8-16 X 1" LG

(2) P/N A84186


4. SERVICE BALLAST.

FITTER CAP DETAIL

PLACE WIRING IN POLE AND SECURE FIXTURETO POLE (HARDWARE AS NOTED).INSTALLATION COMPLETE.

NOTE: ASSEMBLY MUST BE GROUNDED TO THEINCOMING EQUIPMENT GROUND SUPPLY.


(AS SHOWN), CLOSE BALLAST COMPARTMENT.

PLUG IN CONNECTORS FROM ARM TO FIXTURE.


PLUG IN ALL CONNECTORS AND CAREFULLY PLACE

ROTATE FITTER CAP CLOCKWISE, UNTIL TABS SNAP


FITTER CAP

BALLAST

TABS

ASSEMBLE FIXTURE TO ARM WITH (2) CAPTIVE SCREWSPULL LATCH AND LOWER FIXTURE TO ACCESS BALLAST;

COMMON, BLACK TO HOT AND GREEN TO GROUND).

WIRECONNECTIONS

(BY OTHERS)

LAMP (REFERENCE)(BY OTHERS)

SAFETY CALBE


FOR POLE BY OTHERS,HARDWARE BY OTHERS.

HARDWARE INCLUDED.

3.5

10.00

WIREWAY

(2) O 7/16"CLEARANCE

1

1


PART NO.APPRVDDATE

DATE REV.


(714)994-2700 fax(714)994-0522 A96486

PROS DIR


TRA59U

LATCH

CLOSED

TENON

FIXTURE

(BY OTHERS)

CONNECTORS

DOME

4" O.D. POLE (REF)

TABS

BALLAST

FITTER CAP

(ORIENTATION)

2.

2.

4. SERVICE BALLAST.

LAMP SERVICING:


FOR POLE BY OTHERS,HARDWARE BY OTHERS.

HARDWARE INCLUDED.

OPEN

SHCS S/S

3.

4.

TURN OFF POWER.1.

TURN POWER OFF.

3.

1.

3/8-16 X 1" LG

(2) P/N A84186

6.

7.

(BY OTHERS)

5/16-18 X 1/4"


1.2.

3.

5.

4.

CONNECTORS

LAMP (REFERENCE)

FITTER CAP DETAIL

INCOMING EQUIPMENT GROUND SUPPLY.PLACE WIRING IN POLE AND SECURE ARM TO POLE







BALLAST SERVICING:

LIFT FITTER CAP WITH BALLAST FROM FITTER ANDFREE FROM FIXTURE. (SEE FITTER CAP DETAIL)

CLOSE DOME AND LATCH SECURELY.LAMP SERVICING COMPLETE.

PULL LATCH AND RAISE DOME AS SHOWN.INSTALL LAMP (BY OTHERS). AND

MOUNTING HOLES

PLUG IN CONNECTORS FROM ARM TO FIXTURE AND

TO TENON WITH (3) 5/16-18 x 1/4" SET SCREWS.SLIP FIXTURE OVER TENON, AND SECURE FIXTURE



NOTE: ASSEMBLY MUST BE GROUNDED TO THE



(HARDWARE AS NOTED). PLUG IN ALL CONNECTORS AND CAREFULLY PLACE5.

INCOMING WIRE LEADS

COMMON, BLACK TO HOT AND GREEN TO GROUND).

WIRE CONNECTIONS

ARM

3.5

10.00WIREWAY


2

1 2

1


PART NO.APPRVDDATE

DATE REV.


(714)994-2700 fax(714)994-0522 A96487

PROS DIR


WMA59D

(BY OTHERS)WIRE CONNECTIONS

SILICONE

(BY OTHERS)

SCREWSCAPTIVE

DOME DETAIL

FITTER CAP

SCREWS

FIXTURE

DOME

FIXTURE



7.

6.


5.SERVICE BALLAST.4.

2.1.

3.

TURN POWER OFF.

BALLAST SERVICING:

LATCH SECURELY.

1. TURN OFF POWER.

4.

3.


2.

LAMP SERVICING:

TABS

BALLAST

4.

INSTALLATION STEPS:1. TURN OFF POWER.2.

CONNECTORS

CLOSED

HARDWARE BY OTHERS).

INSTALLATION COMPLETE.7.

6.SURFACE AS SHOWN.

5.

WIRE LEADSINCOMING

FRONT OF

ARM

MOUNTING HARDWARE

CONNECTORS

(BY OTHERS)

MOUNTING PLATE


INSTALL LAMP (BY OTHERS). CLOSE FIXTURE ANDPULL LATCH AND LOWER FIXTURE, AS SHOWN.

(ORIENTATION)MOUNTING PLATE

PLACE WIRING IN J-BOX AND MOUNT FIXTUREINCOMING EQUIPMENT GROUND SUPPLY.

FITTER CAP DETAIL

PLUG IN CONNECTORS FROM FIXTURE TO ARM.




LIFT FITTER CAP WITH BALLAST FROM FITTER ANDFREE FROM FIXTURE. (SEE FITTER CAP DETAIL)

JUNCTION BOX

OPEN

NOTE: ASSEMBLY MUST BE GROUNDED TO THECOMMON, BLACK TO HOT AND GREEN TO GROUND).LEADS TO ARM LEADS, AS SHOWN. (WHITE TOMAKE WIRE CONNECTIONS FROM INCOMING WIRE

FIXTURE TO ARM WITH (2) CAPTIVE SCREWS (AS SHOWN),INSTALL LAMP. CLOSE LAMP COMPARTMENT.

SILICONE AROUND MOUNTING PLATE AND MOUNTING

TO WALL. (NOT FOR JUNCTION BOX MOUNTING,

3. PULL LATCH AND RAISE DOME AS SHOWN; ASSEMBLE

(2)CAPTIVE

CONNECTORS

SAFETY CABLE

LATCH

(BY OTHERS)LAMP (REFERENCE)

3.5

10.00

O 1 1/2"

13.94

5.0

WIREWAY



PART NO.APPRVDDATE

DATE REV.


(714)994-2700 fax(714)994-0522 A96488

PROS DIR


WMA59U

LATCH

(BY OTHERS)

ARM

DOME

FITTER CAP

CONNECTORSBALLAST

TABS

JUNCTION BOX(BY OTHERS)

INCOMING WIRE LEADS

(ORIENTATION)

WIRE CONNECTIONS

4. SERVICE BALLAST.5.

6.

7.


TURN POWER OFF.

3.

1.2.

4.

BALLAST SERVICING:

LAMP SERVICING:

2.

3.

TURN OFF POWER.1.

MOUNTING HARDWARE(BY OTHERS)

CLOSED OPEN

5.

6. INSTALLATION COMPLETE.SURFACE, AS SHOWN.

4.

3.

1.INSTALLATION STEPS:

2.TURN OFF POWER.

MOUNTING PLATE

(BY OTHERS) TENON

LAMP (REFERENCE)

CONNECTORS

SILICONE

MOUNTING PLATE

FITTER CAP DETAIL

CLOSE DOME AND LATCH SECURELY.LAMP SERVICING COMPLETE.

RAISE FIXTURE DOME AS SHOWN.


COMMON, BLACK TO HOT AND GREEN TO GROUND).NOTE: ASSEMBLY MUST BE GROUNDED TO THEINCOMING EQUIPMENT GROUND SUPPLY.

BALLAST SERVICING COMPLETE.SECURELY INTO FITTER.



PULL LATCH AND RAISE DOME AS SHOWN.

INSTALL LAMP (BY OTHERS). AND




SLIP FIXTURE OVER TENON, AND SECURE FIXTURETO TENON WITH (3) 5/16-18 x 1/4" SET SCREWS.SILICONE AROUND MOUNTING PLATE AND MOUNTING


MAKE WIRE CONNECTIONS FROM INCOMING WIRELEADS TO ARM LEADS, AS SHOWN. (WHITE TO

PLACE WIRING IN J-BOX AND MOUNT FIXTURE TOMOUNTING SURFACE. (NOT FOR JUNCTION BOX

FIXTURE

MOUNTING, HARDWARE BY OTHERS).


5/16-18 X 1/4"

1

1

3.5

10.00

5.0

13.94

WIREWAY



PART NO.APPRVDDATE

DATE REV.


(714)994-2700 fax(714)994-0522 A96489

PROS DIR


WIRE LEADSINCOMING

FIXTURE

DOME

(BY OTHERS)LAMP (REFERENCE)

LATCH

TABS

FITTER CAP

CONNECTORS

(BY OTHERS)WIRE CONNECTIONS

BALLAST

3" O.D. POLE

2.

GROUND SUPPLY.3.

INSTALLATION STEPS:1. TURN OFF POWER.

1.

4.

3.2.

LAMP SERVICING:

CLOSED OPEN


BALLAST INTO FITTER.5.

SERVICE BALLAST.4.

7.

6.

3.

TURN POWER OFF.

BALLAST SERVICING:1.2.

4.

FITTER CAP DETAIL




MAKE WIRE CONNECTIONS FROM INCOMING WIRELEADS TO FIXTURE. (WHITE TO COMMON, BLACKTO HOT AND GREEN TO GROUND). NOTE: ASSEMBLYMUST BE GROUNDED TO THE INCOMING EQUIPMENT





POLE WITH (3) 5/16-18 x 1/4" SET SCREWS.SLIP FIXTURE OVER POLE, AND SECURE FIXTURE TO


TURN OFF POWER.

LAMP SERVICING COMPLETE.CLOSE DOME AND LATCH SECURELY.INSTALL LAMP (BY OTHERS). ANDPULL LATCH AND RAISE DOME AS SHOWN.

SET SCREW S/S(3) P/N 93007472

5/16-18 X 1/4"

1

1


PART NO.APPRVDDATE

DATE REV.


(714)994-2700 fax(714)994-0522 A96490

PROS IND


TRA59D

3.

5.

2.1.

4.


2.1. TURN POWER OFF.

LAMP SERVICING:

6.LATCH SECURELY.

TO RELEASE BALLAST,SERVICE BALLAST.

SHCS S/S(2) P/N A84186

3/8-16 X 1" LG

6.

PHMS S/S

2.

4.

3.

1. TURN OFF POWER.

5.4.

(2) P/N A84031

8-32 X 1/4"

6.

5.

WIRE LEADSINCOMING

WIRE

(REFERENCE)4" O.D. POLE

CONNECTORS

ARM

CONNECTORS

LATCH

BALLAST

FITTER CAP

DOME(ORIENTATION)

SCREWSCAPTIVE

FIXTURE

FRONT OFFIXTURE

(BY OTHERS)

CAREFULLY PLACE FITTER CAP ASSEMBLY INTOINSTALL LAMP (BY OTHERS).





PULL LATCH AND LOWER FIXTURE TO ACCESS BALLAST.


AND SECURE WITH (2) SCREWS. CLOSE FIXTURE

DOME DETAIL

CLOSED OPEN

INCOMING EQUIPMENT GROUND SUPPLY.NOTE: ASSEMBLY MUST BE GROUNDED TO THECOMMON, BLACK TO HOT AND GREEN TO GROUND).

INSTALLATION COMPLETE.TO POLE (HARDWARE AS NOTED).PLACE WIRING IN POLE AND SECURE FIXTURE

INSTALLATION STEPS:



(AS SHOWN), CLOSE BALLAST COMPARTMENT.

FITTER, ROTATE FITTER CAP CLOCKWISE UNTIL TABSSNAP SECURELY INTO FITTER.LAMP SERVICING COMPLETE.

FITTER CAP DETAIL

LEADS TO ARM LEADS, AS SHOWN. (WHITE TO 3. LIFT FITTER CAP FROM FITTER.

MOUNTING PATTERN

PULL LATCH AND LOWER FIXTURE TO ACCESS BALLAST;ASSEMBLE FIXTURE TO ARM WITH (2) CAPTIVE SCREWS

CAPTIVE SCREWS

LAMP (REFERENCE)

TABS

HARDWARE INCLUDED.

HARDWARE BY OTHERS.FOR POLE BY OTHERS,

FOR POLE BY AAL,MOUNTING HARDWARE

(BY OTHERS)CONNECTIONS

1

2

12

3.5

10.00

WIREWAY



PART NO.APPRVDDATE

DATE REV.


(714)994-2700 fax(714)994-0522 A96491

PROS IND


TRA59D

(BY OTHERS)

(BY OTHERS)

TABS

FITTER CAP CLOSED

ARM

DOME

FIXTURE

6.

4.5.

2.1.

6.

3.

4.

1.

3.

1.

7.

5.

6.

2.

WIRE LEADSINCOMING

4.

2.

(BY OTHERS)JUNCTION BOX

MOUNTING PLATE

SILICONE

CONNECTORS

BALLAST

LATCH

CONNECTORS

OPEN

(ORIENTATION)MOUNTING PLATE

SCREWS(2)CAPTIVE

TURN POWER OFF.LAMP SERVICING:

TO RELEASE BALLAST.SERVICE BALLAST.


FIXTURE

SURFACE, AS SHOWN.

INSTALLATION STEPS:

DOME DETAIL

TURN OFF POWER.

(BY OTHERS)

INTO FITTER.

LATCH SECURELY.

MOUNTING HARDWARE

5.

FRONT OF

(2)CAPTIVE SCREWS

PULL LATCH AND LOWER FIXTURE TO ACCESS BALLAST.

FREE FROM FIXTURE. (SEE FITTER CAP DETAIL)ROTATE FITTER CAP COUNTER CLOCKWISE, UNTIL

MOUNTING, HARDWARE BY OTHERS).MOUNTING SURFACE. (NOT FOR JUNCTION BOXPLACE WIRING IN J-BOX AND MOUNT FIXTURE TO


SILICONE AROUND MOUNTING PLATE AND MOUNTING


PLUG IN CONNECTORS FROM ARM TO FIXTURE.PULL LATCH AND LOWER FIXTURE TO ACCESS BALLAST;ASSEMBLE FIXTURE TO ARM WITH (2) CAPTIVE SCREWS(AS SHOWN), CLOSE LAMP COMPARTMENT.

INCOMING EQUIPMENT GROUND SUPPLY.NOTE: ASSEMBLY MUST BE GROUNDED TO THECOMMON, BLACK TO HOT AND GREEN TO GROUND).LEADS TO ARM LEADS, AS SHOWN. (WHITE TO

FITTER CAP CLOCKWISE UNTIL TABS SNAP SECURELY


CAREFULLY PLACE FITTER CAP INTO FITTER, ROTATEINSTALL LAMP (BY OTHERS).


AND SECURE WITH (2) SCREWS. CLOSE FIXTURE AND



3. LIFT FITTER CAP FROM FITTER.

WIRE CONNECTIONS

8-32 X 1/4"PHMS S/S

(2) P/N A84031

LAMP (REFERENCE)

FITTER CAP DETAIL

1

1

3.5

10.00

O 1 1/2"

5.0

13.94

WIREWAY


led upgrade kit installation guide - · pdf filefixture: pros - providence small ... steps: to...

Documents