leica lino l2p5 / l2p5g · technicaldata techncaldaa leicalinol2p5/l2p5g 3 description l2p5 l2p5g...

Leica LINO L2P5 / L2P5G

Overview 2

Technical data 3

Instrument Set-up 4

Operations 7

How to use the smart adapters 9

Message Codes 11

Accuracy Check 12

Care 16

Warranty 17

Safety instructions 18

Leica Lino L2P5/L2P5G 1

OverviewOv e rv ie w

The Leica Lino L2P5/L2P5G is a self-levellingmul-tifunctional laser. It combines the advantage of across-line laser and a point laser in one tool. It is areliable precision laser for any kind of tasks like lev-elling, plumbing, transfering and setting out rightangles.It supports you on job side with two crossing ver-tical and horizontal linesand five points (fourpoints and one intersection point in front of thedevice) which are arranged precisely in 90° toeach other.

1 Window of vertical line and plumb uppoint

2 Window of horizontal line and hori-zontal transfer points

3 Window of plumbing

4 StatusLED (on keypad)

5 Laser key (on keypad), ON/OFF

6 Keypad

7 Levelling lock

8 Battery pack

9 Tripod thread 1/4"

There are 2 different typesavailable:

l L2P5 (red laser)

l L2P5G (green laser)

On all images in this document only the redlaser version is shown.


Technical dataTe c h n ic a ld a ta


Description L2P5 L2P5GBeam direction/fan angle Vertical / >170°, Horizontal / >180°Point direction Up, down, right, left, front (90°/180°)Range* 25m (82 ft) 35m (115 ft)Range*with receiver 80m (262 ft)Levelling accuracy ±0.2mm/m =±2.0mm@10m (±0.002 in/ft = ±0.08 in@ 33ft)Horizontal/Vertical line accuracy ±0.3mm/m (±0.004 in/ft)Point accuracy ±0.2mm/m (±0.002 in/ft)Self-levelling range ±4 °Self-levelling time <3 sOut-of-levelwarning Yes - blink linesevery 5 sLevelling system Automatic pendulum lockable

Laser type 635 ±5 nm, Class2 (acc. IEC 60825-1) 525 ±5 nm, Class2 (acc. IEC 60825-1)Protection class IP 54 (IEC 60529) dust and splash waterDrop resistant 6 x0.5m (1.64 ft)Battery type Lino Li-Ion battery pack5200mAh / 18.7Wh (3 alkaline AA)

Operating time with Li-Ion battery 26h (2 beam +4 point) -44h (1 beam +2 point) continuous

15h (2 beam +4 point) -28h (1 beam+2 point) continuous

Operating time with alkaline batteries 8h (2 beam +4 point) -13h (1 beam +2 point) continuous

4h (2 beam +4 point) -7h (1 beam+2 point) continuous

Automatic shut-off Available

Dimensions (L xWxH) 110 x60 x100mm (4.33 x2.36 x3.93 in)

Weight with Li-Ion battery 530 g (1.17 lbs)

Operating temperature -10…+50 °C (+14…+122 °F)

Storage temperature -25…+70 °C (-13…+158 °F)

Laser line width at 5m distance <2mm (<0.08 in)

Tripod thread 1/4’’ (+ 5/8’’ with adapter)

Pulse power for receiver Yes, auto

* depending on lighting conditions

Instrument Set-upIn s tru me n tSe t-u p

IntroductionThe safety instructions (see Safety Instruc-tions) and the user manual should be readthrough carefully before the product is usedfor the first time.

The person responsible for the product mustensure that all users understand these dir-ectionsand adhere to them.

The symbols used have the followingmeanings:

WARNING

Indicatesa potentially hazardous situation or anunintended use which, if not avoided, will result indeath or serious injury.

CAUTION

Indicatesa potentially hazardous situation or anunintended use which, if not avoided, may result inminor injury and/or appreciablematerial, financialand environmental damage.

Important paragraphswhichmust beadhered to in practice as theyenable theproduct to be used in a technically correctand efficient manner.

Levelling lock

Levelling unlocked

In the unlocked position the instrument auto-matically levels itself within the specified inclin-ation range. (See Technical data)

Levelling locked

Turn the levelling lock in order to transport or tiltthe instrument beyond the self-levelling range.When locked, the pendulum is fixed and the self-levelling function is deactivated. In this case thelaser blinksevery 5sec.


Instrument Set-up

Laser receiverTo be able to detect the laser linesover long dis-tancesor in unfavourable lighting conditions, alaser receiver can be used.

We recommend the Leica RGR200 laserreceiver.

The Lino is powered byXRANGE technologyandtherefore automatically detected by the receiver.

Li-Ion battery

Charge Li-Ion battery

Charge the Li-Ion battery before using it for thefirst time.While charging, the instrument mayheatup. This is normal and should not affect the instru-ment´s lifespan or performance. At the recom-mended storage temperature of -20°C to +30°C(-4°F to +86°F), batteries containing a 50%to100%charge can be stored up to 1 year. After thisstorage period the batteriesmust be recharged.

CAUTION

Connecting the charger using the wrong adaptermaycause seriousdamage to the instrument. Anydamage caused bymisuse is not covered bywar-ranty. Use only Leica-approved chargers, bat-teries and cables. Unapproved chargers or cablescan cause the battery to explode or damage theinstrument.


Instrument Set-up

Insert Li-Ion battery

Insert the battery-packbypressing it down andthen tilting it towards the housing as shown until itsnaps in.

Li-Ion status LED

lights green: charging battery

OFF: charging finished / no charging

Alkaline batteries

To ensure a reliable use, we recommendusing high qualityAlkaline batteries.

Insert Alkaline batteries

Insert Alkaline batteries in the battery-pack.

Insert the battery-pack

Insert the battery-packbypressing it down andthen tilting it towards the housing as shown until itsnaps in.


OperationsOp e ra tio n s

Switching ON/OFF Auto power-offPlace the lock switch to the unlocked position(see Levelling lock). To activate auto power-off after 30min operation pressand hold theOn button at start for 5 sec. The statusLEDblinks3 times in green colour. To deactivateit again repeat the described stepsuntil thestatusLED blinks3 times in red colour.


Operations

Functions

Check if self-levelling is required and cor-respondingly activated. (See Levelling lockfor details)

Vertical linesand dots / horizontal linesand dotson

Horizontal line and dots on Vertical line and dots on


How to use the smart adaptersHowto u s e th e s ma rta d a p te rs

Setup device to adapter

Snap the device on the Twist 360 adapter.

Alignment of vertical laser lines

Turn the device 360° around the plumb point toadjust the vertical line.

Alignment of horizontal laser lines

Turn the adjustment knob of UAL130 to fine adjustthe horizonal line to the desired reference level.


How to use the smart adapters

Different fixing applications


Message CodesMe s s a g e Co d e s


Laser LED Cause Correction

ON/OFF lights red Instrument has low power Charge Li-Ion battery or changeAlkaline batteries

OFF blinks red Temperature alert Cool down or heat up instrument

blinks blinks red Instrument is out of self-levellingrange

Place the instrument almost hori-zontal and self-levelling will startautomatically

blinks lights red Instrument is out of self-levellingrange and has low power

Charge Li-Ion battery or changeAlkaline batteries

blinksevery 5 sec lights red Levelling lock is activated butinstrument has low power

Charge Li-Ion battery or changeAlkaline batteries

blinksevery 5 sec blinksgreen Levelling lock is activated for work-ing without self-levelling

Accuracy CheckAc c u ra c y Ch e c k

Check the accuracyof your Leica Lino reg-ularly and particularly before important meas-uring tasks. Check Levelling lockbeforechecking the accuracy.

Levelling

Checking the accuracy of the levelling

Set the instrument on a tripod half-waybetweentwo walls (A+B) that are approx. 5m apart. Placethe lock switch in the "Unlocked" position (see Lev-elling lock). Direct the instrument at wall A andswitch on the instrument. Activate the horizontallaser line or laser point andmark the position ofthe line or the point on wall (A1). Rotate the instru-ment by180° andmark the horizontal laser line orthe laser point in exactly the samewayon wall(B1).

Then place the instrument at the same elevationas close aspossible to wallA and againmark thehorizontal laser line or the laser point on wallA(A2). Rotate the instrument by180° again andmark the laser on wallB (B2). Measure the dis-tancesof themarked pointsA1-A2 and B1-B2.Calculate the difference of the twomeas-urements.

|(A1 - A2) - (B1 - B2)| <=2mm

If the difference doesnot exceed 2mm, then theLeica Lino iswithin tolerance.

Should your Leica Lino be outside of the spe-cified tolerance, please contact a local dealeror an authorised Leica Geosystemsdis-tributor.


Accuracy Check

Vertical and horizontal line

Checking the accuracy of the horizontal line

Place the lock switch in the "Unlocked" position(see Levelling lock). Position the instrumentapprox. 5m away from the wall. Direct the instru-ment at the wall and switch on. Activate the laserline andmark the intersection point of lasercrosshairs on the wall. Swivel the instrument to theright and then to the left. Observe the vertical devi-ation of the horizontal line from themarking. If thedifference doesnot exceed 3mm, then the LeicaLino iswithin tolerance.

Checking the accuracy of the vertical line

Place the lock switch in the "Unlocked" position(see Levelling lock). Asa reference, use a plumb-bob and attach it as close aspossible to an approx.3m high wall. Position the instrument at a distanceof approx. 1.5m from the wall at an elevation ofapprox. 1.5m. Direct the instrument at the walland switch on. Rotate the instrument and align itwith the bottom of the plumb line. Now read off themaximum deviation of the laser line from the top ofthe plumb line. If the difference doesnot exceed 2mm, then the Leica Lino iswithin tolerance.


Vertical plumb points

Checking the accuracy of the upper plumbpoint:

Place the lock switch in the "Unlocked" position(see Levelling lock). Set up the laser on its tripod towallmount bracket near point A1 at aminimum dis-tance of 1.5m from point B1. The horizontal laseris aligned in direction 1. Mark the laser pointsA1and B1with a pin.

Checking the accuracy of the lower plumbpoint:


Accuracy Check

Rotate the instrument by180° so that it points inthe opposite direction 2 to direction 1. Adjust theinstrument so that the laser beam hits point A1exactly. If point B2 is no further than 2mm awayfrom point B1, then the Leica Lino iswithin tol-erance.


Perpendicularity horizontal points

Place lock switch in "Unlocked" position (see Lev-elling lock). Mark a reference point (P1) approx.5m from the walls and position the lower plumbpoint exactly on it. Align the crosshair to the leftwall andmark the intersection point (a1) approx.on the same hight like P1 to the wall. Shortly aftermark the right-hand perpendicular beam (b1) onthe front wall.

Then rotate the device exactly 90° clockwisearound the plumb point P1 and position the left-

hand perpendicular beam to the existing ref-erence point a1. Make sure that the upper plumbpoint is still exactly on the reference P1. Checkafterwards the new reference point b2 with the oldreference b1 on the front wall. The deviationbetween the two pointsmaybemax. 3mm.Markthe new position of the right-hand perpendicularbeam to the right wallwith c1.


Afterwards turn the device exactly 180° aroundthe plumb point P1 and position the right-hand per-pendicular beam to the existing reference pointa1. Make sure that the upper plumb point is stillexactly on the reference P1. Thenmark the left-hand beam to the right wall andmark it with c2. Fin-allymeasure the difference between the formerreference point c1 and the new point c2. The devi-ationmaybemax. 3mm between these twopoints.


Accuracy Check



CareCa re

Never immerse the device in water.Wipe off dirtwith a damp soft cloth. Never use aggressivecleaning agents or solvents. Treat the instrumentwith the same care that you would apply to bin-oculars or a camera. Dropping or violent shakingof the instrument maydamage it. Check the instru-ment for anydamage before using it. Check thelevelling accuracyof the instrument regularly.

To warranty the best precision and visibility pleaseclean the optics of your device regularly. There-fore blow off the dust from the glasseswithouttouching the opticswith your fingers. If necessaryuse a damp soft cloth and a little bit of pure alcohol.

To avoid wrongmeasurements also clean youradapters regularly. This could be done also by theproposed recommendation. Especially the inter-face between the adapter and device shouldalwaysbe clean to enable easy rotation. To cleanthemagnetic surface you could use compressedair or modelling clay.

If the equipment get wet alwaysdry it (max.70°C/158°F) before repacking it into the case.


WarrantyWa rra n ty

International Limited WarrantyThe Leica Lino comeswith a two year warrantyfrom Leica GeosystemsAG. To receive an addi-tional year warranty, the product must beregistered on our website at http://myworld.leica-geosystems.comwithin eight weeks of the pur-chase date. If the product is not registered, ourtwo year warranty applies.

More detailed information about the InternationalLimitedWarranty can be found on the internet at:www.leica-geo-systems.com/internationalwarranty.

Calibration and repair serviceLeica Geosystems recommend to check thedevice within regular intervals to prove the func-tion and reliability in accordance with standardsand requirements. At least one time per year.

In case of damaging your product please neverattemp to repair the device yourself.

For calibration or repair service please visit yourlocal dealer or any certified Leica Geosystemsdis-tributor.


http://myworld.leica-geosystems.com/

http://myworld.leica-geosystems.com/

http://www.leica-geosystems.com/internationalwarranty

http://www.leica-geosystems.com/internationalwarranty

Safety instructionsSa fe ty in s tru c tio n s

The person responsible for the instrumentmust ensure that all users understand thesedirectionsand adhere to them.

Areas of responsibility

Responsibilities of the manufacturer of the ori-ginal equipment:

Leica GeosystemsAGHeinrich-Wild-StrasseCH-9435 HeerbruggInternet: www.leica-geosystems.com

The companyabove is responsible for supplyingthe product, including the User Manual in a com-pletely safe condition.

The companyabove is not responsible for thirdparty accessories.

Responsibilities of the person in charge of theinstrument:

1. To understand the safety instructionsonthe product and the instructions in theUser Manual.

2. To be familiar with local safety regulationsrelating to accident prevention.

3. Alwaysprevent access to the product byunauthorised personnel.

Permitted use1. Projection of horizontal and vertical laser

linesand laser points


Safety instructions

Prohibited use1. Using the product without instruction

2. Using outside the stated limits

3. Deactivation of safety systemsandremoval of explanatory and hazard labels

4. Opening of the equipment byusing tools(screwdrivers, etc.)

5. Carrying out modification or conversionof the product

6. Deliberate dazzling of third parties; also inthe dark

7. Inadequate safeguardsat the surveyingsite (e.g. whenmeasuring on roads, con-struction sites, etc.)

Hazards in use

WARNING

Watch out for erroneousmeasurements if theinstrument is defective or if it hasbeen dropped orhasbeenmisused or modified. Carry out periodictest measurements. Particularly after the instru-ment hasbeen subject to abnormal use, andbefore, during and after important meas-urements.

CAUTION

Never attempt to repair the product yourself. Incase of damage, contact a local dealer.

WARNING

Changesor modificationsnot expressivelyapproved byLeica Geosystems/manufacturer forcompliance could void the user´s authority to oper-ate the equipment.

WARNING

Laser/adapters should not be used in the vicinity ofpacemaker because of integratedmagnetswhichcan affect the function of the pacemaker.

Limits of use

Refer to section Technical data. The instru-ment is designed for use in areasper-manently habitable for humans. Do not usethe product in explosion hazardousareasorin aggressive environments.


Safety instructions

Disposal

CAUTION

Flat batteriesmust not be disposed of with house-hold waste. Care for the environment and takethem to the collection points provided in accord-ance with national or local regulations.

The product must not be disposed withhousehold waste. Dispose of the productappropriately in accordance with the nationalregulations in force in your country. Adhereto the national and country specific reg-ulations.

Product specific treatment and wasteman-agement can be downloaded from ourhomepage.

Transport

Transport of instrumentAlways set the device in "Locked" position by turn-ing the lock switch when transporting the device(see Levelling lock). Please use the original caseor an equivalent packaging for transporting andshipping your measuring device.

Transport of Li-Ion battery

WARNING

During transport, shipping or disposal of batteriesit is possible for inappropriatemechanical influ-ences to constitute a fire hazard.

Precautions:

Before shipping the product or disposing it, dis-charge the batteries by running the product untiltheyare flat. When transporting or shipping bat-teries, the person in charge of the product mustensure that the applicable national and inter-national rules are observed. Before transportationor shipping, contact your local passenger orfreight transport company.

WARNING

Highmechanical stress, high ambient tem-peraturesor immersion into fluids can cause leak-age, fire or explosion of the batteries.

Precautions:

Protect the batteries frommechanical influencesand high ambient temperatures. Do not drop orimmerse batteries into fluids.

For further information about chargingplease refer to Li-Ion battery.


Safety instructions

Electromagnetic Compatibility(EMC)

WARNING

The device conforms to themost stringent require-ments of the relevant standardsand regulations.However, the possibility of causing interference inother devices cannot be totally excluded.

FCC statement (applicable in U.S.)This equipment hasbeen tested and found to com-plywith the limits for a ClassB digital instrument,pursuant to part 15 of the FCC rules. These limitsare designed to provide reasonable protectionagainst harmful interference in a residential install-ation. This equipment generates, usesand canradiate radio frequencyenergyand, if not installedand used in accordance with the instructions, maycause harmful interference to radio com-munications.

However, there is no guarantee that interferencewill not occur in a particular installation. If this equip-ment does cause harmful interference to radio ortelevision reception, which can be determined byturning the equipment off and on, the user isencouraged to try to correct the interference byone or more of the followingmeasures:

1. Reorient or relocate the receivingantenna

2. Increase the separation between theequipment and the receiver

3. Connect the equipment into an outlet ona circuit different from that to which thereceiver is connected

4. Consult the dealer or an experienced radi-o/TV technician for help

This instrument complieswith part 15 of the FCCrules. Operation is subjected to the following twoconditions:

1. This instrument maynot cause harmfulinterference, and

2. this instrument must accept any inter-ference received, including interferencethat maycause undesired operation.

ISED statement (applicable in Canada)

This instrument complieswith IndustryCanadalicense-exempt RSS standard(s). Operation issubjected to the following two conditions:

1. This instrument maynot cause harmfulinterference, and

2. this instrument must accept any inter-ference received, including interferencethat maycause undesired operation.


Safety instructions

Laser classification

The instrument produces visible laser beams,which are emitted from the instrument. It is a Class2 laser product in accordance with:

l IEC60825-1 : 2014 „Radiation safety oflaser products“

Laser Class 2 productsDo not stare into the laser beam or direct ittowardsother people unnecessarily. Eye pro-tection is normally afforded byaversion responsesincluding the blink reflex.

WARNING

Looking directly into the beamwith optical aids(e.g. binoculars, telescopes) can be hazardous.

CAUTION

Looking into the laser beammaybe hazardous tothe eyes.

Wavelength

L2P5: 635 +/- 5 nm (red) / L2P5G: 525 +/- 5 nm(green)

Maximum radiant output power for classification

<1mW

Pulse duration

70 µs, cw (red) / 50 - 70 µs (green)

Pulse repetition frequency

10 kHz

Beam divergence line

< 200°

Beam divergence point

< 1.5mrad


Safety instructions

Labelling

Subject to change (drawings, descriptionsandtechnical data) without prior notice.


leica lino l2p5 / l2p5g · technicaldata techncaldaa leicalinol2p5/l2p5g 3 description l2p5 l2p5g...

Documents