Member of following committees

1. COMMITTEE E34 ON OCCUPATIONAL HEALTH AND SAFETY

This Committee shall be responsible for the development of standard occupational health and

safety test methods, practices, guides and terminology for materials and chemical, physical and

biological agents. Consideration shall be given to:

(1) identification; (2) exposure, including safe levels, methods of measurement, monitoring of

personnel and environment, and medical examinations; (3) syrnptomatology and the need for

treatment and first aid; (4) control, including engineering, personal protective equipment,

precaut onary methods, training, warnings and labels, storage and transportation, handling and

disposal; and (5) administration, including record keeping and registry. The activities of this

Committee shall be coordinated with all relevant committees of ASTM and other organizations.

Areas of standards development applicable to this scope, but under the jurisdiction of other

ASTM committees are specifically excluded unless the appropriate committee does not chose to

act directly on the standards needed as requested by this Committee.

Organizations outside of ASTM developing standards within the scope of this Committee will be

consulted for advice and requested to participate in the activities of this Committee. Cooperation

and coordination will be maintained with all organizations writing standards so that duplication

would be avoided.

2. SUBCOMMITTEE E34.10 ON INDUSTRIAL SAFETY

ACTIVE standards under the jurisdiction of E34.10 E34 Home E1575-12 Standard Practice

for Pressure Water Cleaning and Cutting E2349-12 Standard Practice for Safety Requirements in

Metal Casting Operations: Sand Preparation, Molding, and Core Making; Melting and Pouring;

and Cleaning and Finishing E2875/E2875M-12 Standard Guide for Personal Protective Equipment

for the Handling of Flat Glass

New Standards under the jurisdiction of E34.10 E34 Home WK23145 New Guide for Equipment

Technology and Operations for Mobile and Plant-Based Secure Destruction Safety Requirements

WK44665 New Specification for Safety for Spinning Blades in Table Saws

3. ASTM F1703 - 13 STANDARD GUIDE FOR SKATING AND

ICE HOCKEY PLAYING FACILITIES

1.1 The intent of this guide is to provide consistent considerations for the design,

construction, and retrofitting of ice skating and ice hockey playing facilities. It is intended to

establish guidelines that will provide a level of functionality for recreational skating, conformity

for the purpose of competition and reduce potential hazards to skaters, players, game officials,

spectators, and employees.

1.2 This guide should be taken into consideration by owners/operators, architects, planners,

engineers, equipment manufacturers, construction companies,construction contractors, and

appropriate inspectors who may be involved in the design and construction of new ice

skating/hockey playing facilities. Whenever possible, environmental sustainability and energy

efficiency should be taken into consideration in the planning and design of facilities. This guide

applies only to the construction and development of new ice skating/hockey playing facilities.

Portions, however, may be useful for renovation projects, such as, replacing worn

out dasherboards.

1.3 Every arena is unique in material, architecture, and engineering, and therefore will

require technical review. This guide is not meant to provide an architectural prototype, but is a

guide to set forth measures for the development of safer ice arena venues.

1.4 The values stated in inch-pound units are to be regarded as the standard. The values

given in SI units are for information only.

1.5 This standard does not purport to address all of the safety concerns, if any, associated

with its use. It is the responsibility of the user of

4. ANSI A10.10 : SAFETY REQUIREMENTS FOR TEMPORARY AND

PORTABLE SPACE HEATING DEVICES

This standard provides minimum safety requirements for the selection installation operation and

maintenance of space leafing devices and equipment of temporary and portable design It covers

the heater unit and ,is integral parts through to their connection for fuel Out does not cover

separate supply tanks or calving Purpose. The purpose of this standard s to furnish pap: lance for

the selection installation operation and maintenance of 'temporary and portable space ', eating

devices and equipment used .n construction operations in order to protect against personal id up,

and property damage.

5. ANSI A10.20: SAFE OPERATING PRACTICES FOR TILE

TERRAZZO AND MARBLE WORK

This standard establishes safety requirements for construction operations and equipment used in

the trending and installation of ceramic tile terrazzo and marble The types of construction are not

:iSted The standard intended to apply to buildings of all kinds and to heavy construction such as

work or tunnels Purpose.

The QuiP055 M this standard is to establish safety requirements and practices 'or construction

vernation and equipment involved n the handling and installation of ceramic tile terrazzo and

marble

6. ANSI/ASSE A10.24-2006 ROOFING – SAFETY

REQUIREMENTS LOW-SLOPED ROOFS

This standard establishes safe operating practices for the installation. Maintenance and removal

of membrane roofing that is seamed or seamless on low-sloped roofs with A maximum slope of 4

and 12. These types of roofs Include but are not necessarily limited to: hot and cold built-up

roofing, single-ply roofing, poly urethane foam (PUF) roofing, liquid-type roofing

(Hypalon.polyurethane.etc.). Modified bitumen’s

7. LISTING OF STANDARDS

A10.1 Pre-Project & Pre-Task Safety & Health Planning

A10.2 Safety, Health and Environmental Training (under development)

A10.3 Powder-Actuated Fastening Systems

A10.4 Personnel Hoists and Employee Elevators

A10.5 Material Hoists

A10.6 Demolition Operations

A10.7 Transportation, Storage, Handling and Use of Commercial Explosives and

Blasting Agents

A10.8 Scaffolding

A10.9 Concrete and Masonry Construction

A10.10 Temporary and Portable Space Heating Devices

A10.11 Personnel and Debris Nets

A10.12 Excavation

A10.13 Steel Erection

A10.15 Dredging

A10.16 Tunnels, Shafts and Caissons

A10.17 Safe Operating Practices for Hot Mix Asphalt (HMA) Construction

A10.18 Temporary Roof and Floor Holes, Wall Openings, Stairways and Other

Unprotected Edges

A10.19 Pile Installation and Extraction Operations

A10.20 Ceramic Tile, Terrazzo, and Marble Work

A10.21 Safe Construction and Demolition of Wind Generation/Turbile Facilities (under

development)

A10.22 Rope-Guided and Non-Guided Workers' Hoists

A10.23 Safety Requirements for the Installation of Drilled Shafts (under development)

A10.24 Roofing - Safety Requirements for Low-Sloped Roofs

A10.25 Sanitation in Construction

A10.26 Emergency Procedures for Construction Sites

A10.27 Hot Mix Asphalt Facilities

A10.28 Work Platforms Suspended from Cranes or Derricks

A10.29 Aerial Platforms in Construction (under development)

A10.31 Digger-Derricks

A10.32 Personal Fall Protection Used in Construction and Demolition Operations

A10.33 Safety and Health Program Requirements for Multi-Employer Projects

A10.34 Public Protection

A10.37 Debris Nets

A10.38 Basic Elements of a Program to Provide a Safe and Healthful Work Environment

A10.39 Construction Safety and Health Audit Program

A10.40 Reduction of Musculoskeletal Problems in Construction

A10.41 Equipment Operator and Supervisor Qualifications and Responsibilities (under

development)

A10.42 Rigging Qualifications and Responsibilities in the Construction Industry

A10.43 Confined Spaces in Construction (under development)

A10.44 Lockout/Tagout in Construction