liquid chromatography
DESCRIPTION
Liquid Chromatography. A.) Introduction : Liquid Chromatography (LC) is a chromatographic technique in which the mobile phase is a liquid. LC is a much older technique than GC, but was overshadowed by the rapid development of GC in the 1950’s and 1960’s. - PowerPoint PPT PresentationTRANSCRIPT
Liquid Chromatography A.) Introduction:
Liquid Chromatography (LC) is a chromatographic technique in which the mobile phase is a liquid.
LC is a much older technique than GC, but was overshadowed by the rapid development of GC in the 1950’s and 1960’s.
LC is currently the dominate type of chromatography and is even replacing GC in its more traditional applications.
Advantages of LC compared to GC:1.) LC can be applied to the separation of any compound that is soluble in a liquid phase.
‚LC more useful in the separation of biological compounds, synthetic or natural polymers, and inorganic compounds
2.) Liquid mobile phase allows LC to be used at lower temperatures than required by GC‚ LC better suited than GC for separating compounds that may be thermally
labile
3.) Retention of solutes in LC depend on their interaction with both the mobile phase and stationary phase.
‚ GC retention based on volatility and interaction with stationary phase‚ LC is more flexible in optimizing separations change either stationary or
mobile phase
4.) Most LC detectors are non-destructive‚ most GC detectors are destructive‚ LC is better suited for preparative or process-scale separations
Disadvantage of LC compared to GC: 1.) LC is subject to greater peak or band-broadening.
‚ much larger diffusion coefficients of solutes in gases vs. liquids
B.) Low- and High-performance Liquid Chromatography:
Many types of liquid chromatography are available, based on different stationary phase and mobile phase combinations.
- each type may be further characterized based on its overall efficiency or performance
Mol
ecul
ar m
ass
Low-performance liquid chromatography – LC methods that use large, non-rigid support material
‚ particles > 40 m in diameter– poor system efficiencies and large plate heights– such systems have the following characteristics:
‚ broad peaks ‚ poor limits of detection‚long separation times ‚columns can only tolerate low operating pressures
gravity flow or peristaltic pump to apply mobile phase to column
Solvent reservoir
Column head
Column
Column packing
Porous glass plate
Column chromatography – an example of the equipment used in low-performance liquid chromatography
‚ Sample is usually applied directly to the top of the column.‚ Detection is by fraction collection with later analysis of each fraction
Low-performance liquid chromatography
advantages:– simple system requirements
– low cost
– popular in sample purification
– used in the removal of interferences from samples
– used in some analytical applications
‚ not common due to low efficiency, long analysis times and poor limits of detection
High-performance liquid chromatography (HPLC)
– LC methods that use small, uniform, rigid support material
‚ particles < 40 m in diameter
‚ usually 3-10 m in practice
– good system efficiencies and
small plate heights
– such systems have the following
characteristics:
‚ narrow peaks
‚ low limits of detection
‚short separation times ‚columns can only tolerate high
operating pressures and faster flow-rates
A typical HPLC system:
- Higher operating pressures need for mobile phase delivery requires special pumps and other system components
- Sample applied using closed system (i.e., injection valve)
- detection uses a flow through detector
a)
b)
High-performance liquid chromatography
advantages:– fast analysis time
– ease of automation
– good limits of detection
– preferred choice for analytical applications
– popular for purification work
disadvantages:– greater expense
– lower sample capacities
C.) Elution:Retention and elution of solutes in LC depends on the interactions of solutes with both the mobile and stationary phases.
- to describe how well solutes are retained on a column with different solvents, the terms weak
mobile phase and strong mobile phase are used.
Strong mobile phase: a solvent that quickly elutes solutes from the column (i.e., small k’)
This occurs if the mobile phase is very similar to the stationary phase in its intermolecular interactions with the solutes
- polar solvent would be a strong mobile phase for a column containing a polar stationary phase
Rapid elution in a few minutes for all compounds in the mixture
Slow elution (~ 20 minutes) for all compounds in the mixture
C.) Elution:
Weak mobile phase: a solvent that slowly elutes solutes from the column (i.e., high solute retention or large k’)
This occurs if the mobile phase is very different from the stationary phase in its intermolecular interactions with the solutes
- a non-polar solvent would be a weak mobile phase for a column containing a polar stationary phase
Note: whether a solvent is a weak or strong mobile phase depends on the stationary phase being used. Hexane is a weak mobile phase on a polar stationary phase, but a strong mobile phase on a non-polar stationary phase.
Similar to GC, solutes can be eluted from a column by using either a constant column conditions or gradient elution
Isocratic elution: use of a constant mobile phase composition to elute solutes
‚ simple, inexpensive
‚ difficult to elute all solutes with good resolution in a reasonable amount of time general elution problem
Need to identify solvent composition to obtain optimal separation
Journal of Chromatography A, 1109 (2006) 253-266
Similar to GC, solutes can be eluted from a column by using either a constant column conditions or gradient elution
Gradient elution: changing composition of mobile phase with time solvent programming‚ going from a weak mobile phase to a strong one.
‚ weak mobile phase solvent A
‚ strong mobile phase solvent B
‚ solvent change can be stepwise, linear or non-linear
In choosing a mobile phase for LC, several factors need to be considered – type of stationary phase used
‚determines what will be a strong or weak mobile phase– solubility of the solutes– viscosity of the mobile phase– type of detector used and solvent's background signal– purity of the solvents– miscibility of the solvents (for gradient elution)
Gradient elution of mixture of 30 amino-acids
SolventRefractive Index
Viscosity (cP)
Boiling Point (oC)
Polarity Index (P)
Eluent Strength (o)
Fluoroalkanes 1.27-1.29 0.4-2.6 50-174 <-2 -0.25
cyclohexane 1.423 0.90 81 0.04 -0.2
N-hexane 1.327 0.30 69 0.1 0.01
1-chlorobutane 1.400 0.42 78 1.0 0.26
Carbon tetrachloride 1.457 0.90 77 1.6 0.18
i-propyl ether 1.365 0.38 68 2.4 0.28
toluene 1.494 0.55 110 2.4 0.29
Diethyl ether 1.350 0.24 35 2.8 0.38
tetrahydrofuran 1.405 0.46 66 4.0 0.57
chloroform 1.443 0.53 61 4.1 0.40
ethanol 1.359 1.08 78 4.3 0.88
Ethyl acetate 1.370 0.43 77 4.4 0.58
dioxane 1.420 1.2 101 4.8 0.56
methanol 1.326 0.54 65 5.1 0.95
acetonitrile 1.341 0.34 82 5.8 0.65
nitromethane 1.380 0.61 101 6.0 0.64
Ethylene glycol 1.431 16.5 182 6.9 1.11
water 1.333 0.89 100 10.2 large
Selection of a mobile phase for a particular LC application can be done by using various tables that summarize properties for common LC solvents:
D.) Types of Liquid Chromatography:
Techniques in LC are classified according to the method of solute separation
‚ Adsorption chromatography ‚ Affinity chromatography
‚ Partition chromatography ‚ Size-exclusion chromatography
‚Ion-exchange chromatography
1.) Adsorption ChromatographySeparates solutes based on their adsorption to underivatized solid particles.‚ similar to gas-solid chromatography in that the same material is used as both the stationary phase and support material
advantages:– retain and separate some compounds that can not be separated by other
methods
‚ separation of geometrical isomers disadvantages:
– very strong retention of some solutes
– may cause catalytic changes in solutes
– solid support may have a range of chemical and physical environments non-
symmetrical peaks and variable retention times
Mobile phase
Adsorption chromatography stationary phase (or solid support) may be either polar or non-polar
Adsorbent Surface Type Application
Silica Slightly acidic General Purpose – Basic compounds
Alumina Slightly basic General Purpose – Acidic Compounds
Charcoal Non-polar Non-polar Compounds
Florisil Strongly acidic General purpose – Basic Compounds
Polyamides Basic Phenols and Aromatic Nitro Compounds
Others (clay, Kieselguhr, diatomaceous earth, celite, etc.)
Relatively Non-polar Polar Compounds
For polar supports (silica/alumina), the weak mobile phase is a non-polar solvent (hexane, benzene, etc.) and the strong mobile phase is a polar solvent (water, methanol, etc.)
For non-polar supports (charcoal), the weak mobile phase is a polar solvent and the strong mobile phase is a non-polar solvent.
Common applications of Adsorption LC: - purification of synthetic organic compounds from reaction mixtures- separation of geometrical isomers (ortho/meta/para, cis/trans, etc)
2.) Partition ChromatographySeparates solutes based on their partitioning between a liquid mobile phase and a liquid stationary phase coated on a solid support.
Mobile phase
Support Material – is usually silica, originally involved coating this support with some liquid stationary phase that was not readily soluble in the mobile phase
Two main types of partition chromatography based on the type of stationary phase:‚ normal-phase liquid chromatography‚ reversed-phase liquid chromatography
Normal Phase liquid Chromatography (NPLC).
-partition chromatography where the stationary phase is polar
‚ NPLC column strongly retains polar compounds
- weak mobile phase is a non-polar liquid: organic solvent- strong mobile phase is a polar liquid: water or methanol- stationary phase must have a low miscibility with the mobile phase so the stationary
phase is not dissolved from the column
‚examples of liquid NPLC stationary phases:
Dimethylsulfoxide Water
Ethylene glycol Ethylene diamine
CN Cyanopropyl
NH2 Aminopropyl
PSA N-propylethylenediamine
Si CH2CH2CH2CN
Si CH2CH2CH2NH2
Si CH2CH2CH2NHCH2CH2NH2
These liquid stationary phases slowly bleed from the column, changing the properties and solute retention time .
Use stationary phases chemically attached to the support
Common applications of NPLC: - purification of synthetic organic and inorganic compounds from reaction mixtures- general purpose separation of polar/non-polar compounds when the sample is in a non-polar solvent
PrepLCMS Analysis (50 mg injection)
4.36
5
2e7
4e7
6e7
8e7
Inte
nsi
ty, cp
s
DesiredProduct
Automated chromatography purification of designed drug combinatorial libraries
Reverse Phase liquid Chromatography (RPLC).
-partition chromatography where the stationary phase is non-polar
‚ reverse polarity of normal phase LC
‚ retains non-polar compounds most strongly
- weak mobile phase is a polar liquid: water- strong mobile phase is more non-polar liquid: methanol or acetonitrile- stationary phase must have a low miscibility with the mobile phase so the
stationary phase is not dissolved from the column ‚examples of liquid RPLC stationary phases:
heptane squalene
hydrocarbon polymers dimethylpolysiloxane
Comparison of RPLC & NPLC
Type Stationary phase Weak mobile phase Strong Mobile phase
RPLC Non-polar Polar liquid More non-polar
NPLC polar Non-polar liquid Polar liquid
C18 Octadecyl
C8 Octyl
C2 Ethyl
CH Cyclohexyl
PH Phenyl
Si C18H37
Si C8H17
Si C2H5
Si
Si
Use stationary phases chemically attached to the support, C8 and C18 are most common
Like NPLC, these liquid stationary phases slowly bleed from the column, changing the properties and solute retention time.
Common applications of RPLC: - most popular type of liquid chromatography
‚ separation of a wide variety of non-polar and polar solutes
- popularity weak mobile phase is a polar solvent (e.g., water)
‚ ideal for the separation of solutes in aqueous-based samples, such as biological compounds
Common applications of RPLC (continued): - purification of biological and organic compounds present in aqueous solutions- pharmaceutical analysis (drug quantitation and quality control) - protein & peptide mapping- analysis of soil and water samples- clinical analysis of blood and urine samples
RPLC Analysis of Patient blood serum for presence of drug during clinical trial
3.) Ion-exchange Chromatography (IEC)Separates solutes by their adsorption onto a support containing fixed charges on its surface. A high concentration of a competing ion is often added to the mobile phase to elute the analytes from the column
xRSO3-H+ + Mx+ (RSO3
-)xMx+ +xH+
xRN(CH3)3OH- + Ax- [RH(CH3)3+]xAx- + xOH-
Two General Types of Stationary Phases Can be Used in IEC: - Cation-exchangers: have fixed negatively charged groups, used to separate positively-charged ions
- Anion-exchangers: have fixed positively-charged groups, used to separate negatively-charged ions
Chemical Structure Functional Group Chemical Nature Type of Exchange
-SO-H+ Sulfonic acid Strong acid Cation
-COO-H+ Carboxylic acid Weak acid Cation
-CH2COO-H+ Carboxymethyl Weak acid Cation
-CH2N+(CH3)3Cl- Quaternary ammonium
Strong base Anion
Quaternary ammonium
Strong base Anion
Tertiary ammonium Weak base Anion
Diethylaminoethyl (DEAE)
Weak base Anion
CH2N+
CH3
CH3
CH2CH2CH(Cl-)
CH2NH+
CH3
CH3
OH-
CH2CH2NH+
CH2CH3
CH2CH3
OH-
The charged groups that make up the stationary phase can be placed on several different types ofsupport materials: Cross-linked polystyrene resins: for use with the separation of inorganic ions and small organic ionsCarbohydrate-based resins: for low-performance separations of biological molecules (dextran, agarose, cellulose)Silica-based supports: for high-performanceseparations of biological molecules
A strong mobile phase in IEC:- contains a high concentration of a competing ion for displacement of the sample ion from the stationary phase
cation exchange resin (Kex):
Tl+ > Ag+ > Cs+ > Rb+ >K+ >NH4+ > Na+ > H+ > Li+
Ba2+ > Pb2+ > Sr2+ > Ca2+ > Ni2+ > Cd2+ > Cu2+ > Co2+ > Zn2+ > Mg2+ > UO22+
anion exchange resin (Kex):
SO42- > C2O4
2- > I- > NO3- > Br- >Cl- > HCO2
- > CH3CO2- > OH- > F-
or
- a solvent that has a pH which decreases ionization of the analyte or stationary phase
rigid polystyrene/divinyl benzene beads
Factors That Affect Mobile Phase Strength Are: - Mobile phase pH
‚ especially for weak acid or base analytes and weak acid or base
stationary phases
- Mobile phase concentration of competing ion - Type of competing ion
Ne
t C
ha
rge
On
Pro
tein
Attached to cationexchangers
Iso
elec
tric
po
int
Range of Stability
Attached to anionexchangers
Common applications of IEC: - Removal or replacement of ionic compounds in samples (sample pretreatment)- Separation of inorganic ions and organic ions - Analysis/purification of charged biological compounds
‚ amino acids, proteins, peptides, nucleic acids
4.) Affinity Chromatography (AC)Separates based on the use of immobilized biological molecules (and related compounds) as the stationary phase
Based on the selective, reversible interactions that characterize most biological systems- binding of an enzyme with its substrate or a hormone with its receptor- immobilize one of a pair of interacting molecules onto a solid support- immobilized molecule on column is referred to as the affinity ligand
Two Main Types of Affinity Ligands Used in AC: High-specificity ligands – compounds which bind to only one or a few very closely related
molecules
General or group specific ligands – molecules which bind to a family or class of related molecules
Affinity Ligand Retained Compounds
Antibodies Antigens
Antigens Antibodies
Inhibitors/Substrates Enzymes
Nucleic Acids Complimentary Nucleic acids
Affinity Ligand Retained Compounds
Lectins Glycoproteins, carbohydrates, membrane proteins
Triazine dyes NADH- or NADPH Dependent Enzymes
Phenylboronic acid Cis-Diol Containing Compounds
Protein A/Protein G Antibodies
Metal Chelates Metal-Binding Proteins & Peptides
Note: the affinity ligand does not necessarily have to be of biological origin
Due to the very selective nature of most biological interactions, the solute of interest is often retained with little interference from other components of the sample.
A weak mobile phase is usually a solvent that mimics the pH, ionic strength and polarity of the solute and ligand in their natural binding environment.
A strong mobile phase is a solvent that produces low retention for the solute-ligand interaction:- by decreasing its binding constant
or- displaces solute by the addition of an agent with competes for solute sites on the column
pHbuffer
compound
Two Approaches to Elution Used in Affinity Chromatography: - Biospecific Elution: solutes are eluted by a mobile phase that contains a compound which competes with sample solutes for the ligand’s active sites.
- very gentle- useful in purification of active biological molecules- produces slow elution with broad solute peaks
- Non-specific elution: change conditions in the column to disrupt the interactions between the sample solutes and immobilized ligand
- done by changing pH or ionic strength- harsher than biospecific elution- gives narrow peaks and faster run times- commonly used in analytical applications of AC
Common applications of AC: - Purification of enzymes, proteins and peptides- Isolation of cells and viruses - Purification of nucleic acids- Specific analysis of components in clinical and biological samples- Study of biomolecular interactions
Purification of His-Tag Protein Using a pH Change
5.) Size Exclusion Chromatography (SEC)separates molecules according to differences in their size
SEC is based on the use of a support material that has a certain range of pore sizes- as solute travels through the support, small molecules can enter the pores while large molecules can not - since the larger molecules sample a smaller volume of the column, they elute before the smaller molecules.- separation based on size or molecular weight
SEC is based on the different interactions of solutes with the flowing mobile phase and the stagnant mobile phase.
- no true stationary phase is present in this system- stagnant mobile phase acts as the “stationary phase”
SEC does not have a “weak” or “strong” mobile phase since retention is based only on size/shape of the analyte and the pore distribution of the support.
- gel filtration chromatography: if an aqueous mobile phase is used - gel permeation chromatography: if an organic mobile phase is used
(usually tetrahydrofuran)
Common applications of SEC: - Separation of Biological Molecules (e.g., proteins from peptides)- Separation/analysis of organic polymers - molecular-weight determination
E.) LC Detectors:
Common types of LC Detectors
‚ Refractive Index Detector ‚ Conductivity Detector
‚ UV/Vis Absorbance Detector ‚ Electrochemical Detector
‚Fluorescence Detector
As in GC, the choice of detector will depend on the analyte and how the LC method is being used (i.e., analytical or preparative scale)
Detector Selectivity Sensitivity Notes
Refractive Index Poor Poor Any component that differs in refractive index from the eluate can be detected, despite its low sensitivity. Cannot be used to perform gradient analysis.
UV/Vis Moderate Good A wide variety of substances can be detected that absorb light from 190 to 900 nm. Sensitivity depends strongly on the component.
Fluorescence Good Excellent Components emitting fluorescence can be detected selectively with high sensitivity. This is often used for pre-column and post-column derivatization.
Conductivity Moderate Good Ionized components are detected. This detector is used mainly for ion chromatography.
Electrochemical Good Excellent Electric currents are detected that are generated by electric oxidation-reduction reactions. Electrically active components are detected with high sensitivity.
1.) Refractive Index Detector (RI)
Measures the overall ability of the mobile phase and its solutes to refract or bend light.‚ one of the few universal detectors available for LC
advantages:– non-destructive and universal detector
‚ applicable to the detection of any solute in LC
– applicable to preliminary LC work where the nature and properties of the solute are unknown
‚ provided concentration is high enough for detection
disadvantages:– high limits of detection (10-6 to 10-5 M)
– difficult to use with gradient elution
Process:– light from source passes through flow-cells containing either sample
stream or a reference stream
– when refractive index is the same between the two cells, no bending of light
occurs at the interface between the flow-cells ‚ maximum amount of light reaches the detector
– as solute elutes, refractive index changes between reference and sample cell
‚ light is bent as it passes through flow cell interface
‚amount of light reaching detector is decreased
1.) Refractive Index Detector (RI)
2.) UV/Vis Absorbance Detector
Measures the ability of solutes to absorb light at a particular wavelength(s) in the ultraviolet (UV) or visible (Vis) wavelength range.‚ most common type of LC detector
Three Common types of UV/Vis Absorbance Detectors
‚ Fixed wavelength detectors
‚ Variable wavelength detectors
‚Photodiode array detectors
2.) UV/Vis Absorbance Detector
Fixed Wavelength Detector absorbance of only one given wavelength is monitored by the system at all times (usually 254 nm)
‚ simplest and cheapest of the UV/Vis detectors
‚ limited in flexibility
‚ limited in types of compounds that can be monitored
Variable Wavelength Detector a single wavelength is monitored at any given time, but any wavelength in a wide spectral range can be selected
‚ wavelengths vary from 190-900 nm.
‚ more expensive, requires more advanced optics
‚ more versatile, used for a wider range of compounds
Photo Diode Array Detector operates by simultaneously monitoring absorbance of solutes at several different wavelengths.
‚ uses a series or an array of several detector cells within the instrument, with
each responding to changes in absorbance at different wavelengths.
‚ entire spectrum of a compound can be taken in a minimum amount of time
‚ useful in detecting the presence of poorly resolved peaks or peak contaminants
Applications: - UV/Vis absorbance detectors can be used to detect any compound that absorbs at the wavelength being monitored- Common wavelengths: ‚ 254 nm for unsaturated organic compounds ‚ 260 nm for nucleic acids
‚ 280 or 215 nm for proteins or peptides- Absorbance detectors can be used with gradient elution
‚ wavelength being monitored is above the cutoff range of the solvents being used in the mobile phase
- limits of detection for fixed and variable UV/Vis absorbance detectors are ~ 10 -8 M- limits of detection for photodiode array detectors are ~ 10-7 M
3.) Fluorescence Detector
A selective LC detector that measures the ability of eluting solutes to fluoresce at a given set of excitation and emission wavelengths
Applications: - Fluorescence can be used to selectively detect any compound that absorbs and emits light at the chosen set of excitation and emission wavelengths ‚ Relatively few compounds undergo fluorescence ‚ high selectivity, low background signal- limits of detection for a fluorescence detector are ~ 10-10 M- Typical applications
‚ drugs
‚ food additives
‚ environmental pollutants
‚ any compound that can be converted to a fluorescent derivative:
alcohols, amines, amino acids and proteins- Can be used with gradient elution
‚ requires extremely pure mobile phases
‚ trace impurities can affect background signal or quench the fluorescence of solutes
3.) Fluorescence Detector
4.) Conductivity Detector
Used in analytical applications of ion-exchange chromatography for the detection of ionic compounds
‚ detector measures the ability of the mobile phase to conduct a current when placed in a flow-cell between two electrodes
‚ current conducted within the cell will depend on the number and types of ions
present in the mobile phase
Two electrodes placed in mobile phase each corresponding to one arm of a Wheatstone Bridge
Typical Wheatstone Bridge
When ions flow into the sensor cell, the impedance between the electrodes changes producing an “out of balance” signal
Applications: - can be used to detect any compound that is ionic or weakly ionic ‚ high selectivity, low background signal
- limits of detection for a conductivity detector are ~ 10-6 M
- Typical applications‚ food components
‚ industrial samples‚ environmental samples
- Can be used with gradient elution‚ constant ionic strength and pH of mobile phase‚ background conductance of the mobile phase is sufficiently low
4.) Conductivity Detector
5.) Electrochemical Detector
Used to monitor any compound in the mobile phase that can undergo an oxidation or reduction
‚ electrochemical detection in liquid chromatography is sometimes referred to as LC/EC
‚ generally includes two or more electrodes which monitor the current that is
produced by the oxidation or reduction of eluting compounds at a fixed potential
‚ generally electrical output is an electron flow generated by a reaction that takes place at the surface of the electrodes.
Column flow
5.) Electrochemical Detector
Applications: - can be used to detect any solute that can undergo oxidation or reduction ‚ detectors can be made specific for a given compound or class of compounds by properly choosing the conditions at the electrodes ‚ high selectivity, low background signal
- limits of detection for a electrochemical detector are ~ 10-11 M
‚ due to extreme accuracy with which chemical measurements,
especially current measurements, can be made
- compounds that can be detected by reduction
‚ aldehydes
‚ ketones
‚ esters
‚ unsaturated compounds
- compounds that can be detected by oxidation
‚ phenols
‚ mercaptans (RSH)
‚ aromatic amines
‚ dihydroxy compounds