liquid process filtration - melt blown cartridge · liquid process filtration - melt blown...

132
LIQUID PROCESS FILTRATION - MELT BLOWN CARTRIDGE MBC Melt Blown Cartridge Melt Blown Filters An economical, disposable, filter element that can be used in a wide range of applications. The MBC depth filter is constructed of 100% polypropylene media for chemical compatibility with a variety of process fluids. The molded core prevents collapse even at elevated temperatures. FDA listed materials All polypropylene material used in manufacturing complies with the regulations of the Food and Drug Administration (FDA) title 21 of the Code of Federal Regulations Sections 174.5, 177.1520, and 177.1630, as applicable for food and beverage contact. Applications Filter Features–Benefits Available in nominal ratings from 1 to 75 microns Graded pore construction for long on-stream life Melt blown media resists dirt unloading as differential pressure increases Non-shedding, High dirt holding capacity FDA listed polypropylene media Economical depth filtration Thermal bonded endcaps optional Free of binders, adhesives and surfactants Molded core for exceptional collapse strength RO Pre-filters Food & beverage Blowdown post filter Aqueous solutions Wastewater Chemicals Rad waste Ink Filter Specifications Media: Polypropylene End caps/Center core: Polypropylene Gaskets/O-Rings: Silicone, Viton, EPDM, Buna-N Micron ratings: 1, 3, 5, 10, 20, 30, 50, 75μm Dimensions and Operating Parameters Nominal lengths: 9.75", 10’’, 20’’, 30’’, 40’’ (24.8, 25.4, 50.8, 76.2, 101.6 cm) Other lengths available Outside diameter: 2.5’’ (6.35 cm), 2.75’’ (6.99 cm) Endcapped Inside diameter: 1.0’’ (2.54 cm) Maximum differential 150 psid @ 68°F (10.3 bar @ 20°C) pressure: 90 psid @ 150°F (6.2 bar @ 66°C) 35 psid @ 176°F (2.4 bar @ 80°C) Recommended changeout pressure differential: 35 psid (2.4 bar) Example: MBC 10-20NN = MBC filter, 10 micron, 20 inches, No End Caps, No Gaskets or O-rings Corporate Office: 2725 Commerce Parkway Auburn Hills, MI 48326 Toll Free: (800) 331-3118 Fax: (248) 377-3172 [email protected] www.tfsi1.com 119

Upload: phamnguyet

Post on 25-May-2018

242 views

Category:

Documents


1 download

TRANSCRIPT

LIQUID PROCESS FILTRATION - MELT BLOWN CARTRIDGEMBC Melt Blown Cartridge Melt Blown Filters An economical, disposable, filter element that can be used in a wide range of applications. The MBC depth filter is constructed of 100% polypropylene media for chemical compatibility with a variety of process fluids. The molded core prevents collapse even at elevated temperatures.

FDA listed materials All polypropylene material used in manufacturing complies with the regulations of the Food and Drug Administration (FDA) title 21 of the Codeof Federal Regulations Sections 174.5, 177.1520, and 177.1630, as applicable for food and beverage contact. Applications

Filter Features–Benefits Available in nominal ratings from 1 to 75 microns Graded pore construction for long on-stream life Melt blown media resists dirt unloading as

differential pressure increases Non-shedding, High dirt holding capacity FDA listed polypropylene media Economical depth filtration Thermal bonded endcaps optional Free of binders, adhesives and surfactants Molded core for exceptional collapse strength

RO Pre-filters Food & beverage Blowdown post filter

Aqueous solutions Wastewater Chemicals

Rad waste Ink

Filter Specifications Media: Polypropylene End caps/Center core: Polypropylene Gaskets/O-Rings: Silicone, Viton, EPDM, Buna-N Micron ratings: 1, 3, 5, 10, 20, 30, 50, 75μm

Dimensions and Operating Parameters Nominal lengths: 9.75", 10’’, 20’’, 30’’, 40’’ (24.8, 25.4, 50.8, 76.2, 101.6 cm) Other lengths available Outside diameter: 2.5’’ (6.35 cm), 2.75’’ (6.99 cm) Endcapped

Inside diameter: 1.0’’ (2.54 cm) Maximum differential 150 psid @ 68°F (10.3 bar @ 20°C) pressure: 90 psid @ 150°F (6.2 bar @ 66°C) 35 psid @ 176°F (2.4 bar @ 80°C) Recommended changeout pressure differential: 35 psid (2.4 bar)

Example: MBC 10-20NN = MBC filter, 10 micron, 20 inches, No End Caps, No Gaskets or O-rings

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118 Fax: (248) 377-3172

[email protected] www.tfsi1.com

119

LIQUID PROCESS FILTRATION - MELT BLOWN CARTRIDGEStratum C Melt Blown Cartridge High Performance Filters For critical customer applications requiring precise and repeatable depth filtration, the Graver Stratum C series melt blown filters deliver exceptional performance. With a multi- zoned construction, true clarifying filtration is achieved with no unloading of captured contaminant.

Stratum Series Features – Benefits Multi-zone melt blown depth filter with a true graded pore structure Thermally bonded fibers for high void volume and long on-stream life. Available in precise 90% removal efficiencies from 0.5 to 75 microns 100% polypropylene – FDA listed materials of construction All components meet USP Class VI criteria and are safe for use in pharmaceutical applications Molded center core for higher temperature and pressure capability

Applications Chemicals Paint/Ink Water Plating Pharmaceuticals Food and beverages Microelectronics Cosmetics

Filter Specifications Media: Polypropylene End caps/center core: Polypropylene Gaskets/O-rings: Silicone, EPDM, Buna N, Santoprene,

Viton and Teflon encapsulated Viton (o-rings only)

Micron ratings: 0.5, 1, 3, 5, 10, 20, 50, 75 Dimensions Nominal lengths: 4, 5, 9.75, 10, 19.5, 20, 29.25, 30,

39, 40 inches (10.2, 12.7, 24.8, 25.4, 49.5, 50.8, 74.3, 76.2, 99.1, 101.6 cm)

Outside diameter: 2.5 in ( 6.35 cm) Inside diameter: 1 in (2.54 cm) Operating Conditions Maximum differential 1 pressure:

50 psid @ 68°F (10.3 bar @ 20°C) 90 psid @ 150°F (6.2 bar @ 66°C) 35 psid @ 176°F (2.4 bar @ 80°C)

Recommended change- out differential pressure: 35 psid (2.4 bar) Steam Sterilization: Stratum single open end style filters may

be autoclaved under no end load conditions for 30 minutes at 121°C. Filters should be cooled to normal operating temperatures prior to use.

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118Fax: (248) 377-3172

[email protected] www.tfsi1.com

120

LIQUID PROCESS FILTRATION - MELT BLOWN CARTRIDGEStratum C Melt Blown Cartridge

Example: STC 5-10P3V = Stratum C filter, 5 micron, 10 inches, 222/Flat Single Open End, Viton

Note: For chemical compatibility, flow rates, and temperature requirements please consult the factory or your local Graver distributor.

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118 Fax: (248) 377-3172

[email protected] www.tfsi1.com

121

LIQUID PROCESS FILTRATION - MELT BLOWN CARTRIDGEFulflo® DuraBond™ Cartridges Economical Filtration With High Strength Thermally Bonded Depth Cartridges Parker’s Fulflo DuraBondTM Cartridges are the most economical high strength filter cartridges available. Featuring an integral rigid thermally bonded construction, the DuraBondTM provides consistent filtration for a wide variety of fluids. Its fixed pore structure acts as a sieve-like particle “classification” filter for pigmented coatings allowing pigments to pass while stopping large agglomerates.

Fulflo® DuraBondTM Cartridges are available in nominal ratings of 1μm, 3μm, 5μm, 10μm, 25μm, 50μm, 75μm and 100μm. Benefits

Fixed pore structure provides efficiency, integrity and optimum particle retention

Thermally bonded bi-component fiber matrix provides rigid dimensionally stable construction without fiber migration

Rigid construction eliminates contaminant unloading and channeling

Corrugated porous surface maximizes dirt holding capacity Silicone free construction will not change coating properties FDA grade polypropylene (DOE only) certified to ANSI/NSF61

standard for contact with drinking water components Polyolefin construction provides broad chemical compatibility for a

variety of applications All materials of construction are FDA listed as acceptable for

potable and edible liquid contact according to CFR Title 21 DuraBondTM cartridges can be easily disposed by shredding,

incinerating or crushing DuraBondTM construction provides particle “classification” effect

with pigmented coatings Double-open-end style is self-sealing without separate gasket

material

Applications

Photographic Chemicals DI water Plating Solutions Bleach R. O. Pre-filtration Organic Solvents Oilfield Fluids Membrane Pre-filtration Industrial Coatings Magnetic Coatings Potable Water Processing Fluids

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118Fax: (248) 377-3172

[email protected] www.tfsi1.com

122

LIQUID PROCESS FILTRATION - MELT BLOWN CARTRIDGEFulflo® DuraBond™ Cartridges

DBC Flow Factors

Rating (µm)

Aqueous Service

PSI/GPM per 10 in Cartridge

DBC1 0.109 DBC3 0.087 DBC5 0.073

DBC10 0.058 DBC25 0.031 DBC50 0.022 DBC75 0.015

DBC100 0.012

DBC Length Factors

Length (in)

Length Factor

9.75 1.0 10.00 1.0 19.50 2.0 20.00 2.0 29.25 3.0 30.00 3.0 39.00 4.0 40.00 4.0 50.00 5.0

Flow Rate and Pressure Drop Formulas Flow rate (gpm) = Clean P x Length Factor Viscosity x Flow Factor

Clean P = Flow rate x viscosity x Flow Factor Length Factor Notes: 1. Clean P is PSI differential at start. 2. Viscosity is centistokes. Use Conversion

Tables for other units. 3. Flow Factor is P/GPM at 1 cks for 10 in

(or single). 4. Length Factors convert flow or P from 10

in (single length) to required cartridge length.

Specifications

Materials of Construction: Filter Medium: Thermal Bonded bi-component matrix of polypropylene/ polyethylene End Caps/Adapters (optional): polyolefin copolymer Seal Options: Various; refer to Ordering Information

Dimensions:

1-1/16 in (27mm) ID x 2-7/16 (62mm) in OD 10, 20, 30, 40, and 50 in continuous nominal lengths

Maximum Recommended Operating Conditions:

Temperature: 175°F (80°C) Pressure: 100 psid (6.8bar)@72°F (27°C) 50 psid (3.4bar)@175°F (80°C) Flow rate: 5gpm (18.9 lpm) per 10 in length. Changeout P: 30 psi (2.1 bar)

Nominal Filtration Ratings:

(90% efficiency) 1, 3, 5, 10, 25, 50, 75, 100 µm

Liquid Particle Retention Ratings (µm) @ Removal Efficiency of:

Cartridge ß = 10 90%

ß = 20 95%

ß = 100 99%

ß = 1000 99.9%

DBC1 1 2 4 5 DBC3 3 4 8 10 DBC5 5 10 16 20

DBC10 10 15 25 30 DBC25 25 30 50 55 DBC50 50 70 80 90 DBC75 75 100 >100 >100

DBC100 100 >100 >100 >100

Beta Ratio (ß) = Upstream Particle Count @ Specified Particle Size and Larger Downstream Particle Count @ Specified Particle Size and Larger Percent Removal Efficiency = (1 1) x 100 Performance determined per ASTM F-795-88. Single-Pass Test using AC test dust in water at a flow rate of 2.5 gpm per 10 in (9.5 lpm per 254 mm).

____________________________________________________________________________________________ Ordering Information

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118 Fax: (248) 377-3172

[email protected] www.tfsi1.com

123

LIQUID PROCESS FILTRATION - MELT BLOWN CARTRIDGECOAX Melt Blown Cartridge

Two Stage Depth Filter Cartridge The COAX Depth Filter cartridge is an integral two stage depth filter. The first stage is made of nonwoven melt blown polypropylene to trap coarser particles. The second stage-inner core is composed of a bi-component polypropylene and polyethylene fiber to provide fine particle retention. This unique design provides a true graded density that offers a marked increase in useful life and dirt capacity. In addition, the rigid nature means there is no flexing of the cartridge and greatly reducing media migration and particle unloading. Filter Features–Benefits Two stage graded density melt blown depth filter maximizes dirt

holding and useful life Inert pure polyolefin construction, non-shedding media Broad chemical compatibility Low extractables.

Meets USP Class VI standards – Acceptable for use in food, beverage and pharmaceutical applications

Applications

Extensive range of lengths and configurations Paint Perfumes Cutting Oils FDA listed materials of construction. CMP Slurries Magnetic Slurries Corn Syrup COAX Filter Specifications Plating Solutions Pre R.O. Coatings Media: Thermally bonded End caps: Polypropylene (when used) Filter Removal Efficiency Gaskets/O-Rings: Silicone, Viton, EPDM, Buna-N Beta Ratio Beta 100 Beta 20 Beta 10 Micron ratings: 0.5, 1, 3, 5, 10, 25, 50, 100, 150? m Efficiency 99% 95% 90% 0.5 micron 4.0 2.0 2.0 1.0 micro 8.0 3.0 1.0

3.0 micron 12.0 5.0 3.0 Dimensions and Operating Parameters 5.0 micron 20.0 8.0 5.0 Nominal lengths: 9.75”, 10’’, 20’’, 30’’, 40’’ 10.0 micron 30.0 13.0 10.0 (24.8, 25.4, 50.8, 76.2, 101.6 cm) 25.0 micron 50.0 30.0 25.0 Outside diameter: 2.6’’ (6.5 cm) 50.0 micron 100.0 60.0 50.0 Inside diameter: 1.0’’ (2.54 cm) 100.0 micron 200.0 125.0 100.0 150.0 micron 250.0 200.0 150.0 Maximum operating Performance Specifications Sanitization

temperature: 140°F (60°C) Maximum operating 100 psid @ 70°F (7 bar @ 21°C) pressure: 2 psid @ 176°F (0.14 bar @ 80°C)

Hot water at 176°F (80°C) at 5 psid (0.35 bar) for 30 min. Autoclavable at 257°F (125°C) for 30 min. (Basic DOE configuration)

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118Fax: (248) 377-3172

[email protected] www.tfsi1.com

124

LIQUID PROCESS FILTRATION - MELT BLOWN CARTRIDGECOAX Melt Blown Cartridge

Example: COAX 25-40RLP3B = COAX filter, 25 micron, 40 inches, Reduced Length, 222/Flat, Buna-N O-rings

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118 Fax: (248) 377-3172

[email protected] www.tfsi1.com

125

LIQUID PROCESS FILTRATION - STRINGWOUND AND WATERFILTRATION

DW Series Precision Wound Filter Cartridges

DW Series Precision Wound Filter Cartridges The DW series is a proven performer in hundreds of fluid filtration applications around the world. With the availability of twelve filtration media, six support core materials and a variety of end fitting options, the DW series filter cartridges are the cartridge of choice for numerous filter applications. For potable water to aggressive chemicals, the DW Series cartridges provide progressive depth filtration with high sediment holding capacity. Precision winding geometry provides consistent performance, reduces surface blinding and ensures full depth of media utilization. DW series filter cartridges provide an economical solution for removal of solid particles from liquids and compressed gases. Micron ratings are available from 0.5 to 200 at nominal 90% efficiency. Cartridges are available in continuous lengths from 4” to 72” and diameters to 4 1/2”. Cartridge housings in various materials are also available from Delta Pure.

Cartridges are available in a variety of size and configurations to fit most filter housings.

Benefits

Wide range of configurations to ensure process compatibility

FDA compliant materials per CFR Title 21 for contact with potable and edible fluids

High sediment holding capacity for longer time between cartridge changes

Continuous lengths up to 72” (183 cm)

Technical support and prompt deliveries

Applications

Process/Potable Water

Pre-Filtration for Membranes and Reverse Osmosis Systems

Food and Beverage

Ground Water Remediation

Various Chemical Solutions

Oils and Solvents

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118Fax: (248) 377-3172

[email protected] www.tfsi1.com

126

LIQUID PROCESS FILTRATION - STRINGWOUND AND WATERFILTRATION

DW Series Precision Wound Filter Cartridges

Flow Rate (GPM Water per 10” Length, 2 1/2" OD)

Note: Please consult factory for data on other media and fluids. Specifications

Cartridge ID: 1” (2.6 cm) nominal std. 1.22” (3.1 cm) and 1.5” (3.8 cm) optional

Cartridge OD: 2” (5 cm) to 4 1/2” (11.4 cm)

Length: 3” (7.6 cm) to 72” (183 cm) Special Lengths Available

Efficiency: 90% nominal; 80% below 3 micron

Recommended Max Change Out Differential Pressure” 30 psid (2 bar)

Max Differential Pressure 60 psid (4 bar)

Max Temperature

Media Polypro Core Polyester Core Tin Core SST Core Polypropylene 180F 180F 180F 180F Cotton 180F 250F 250F 250F Acrylic 180F 250F 250F 250F Rayon 180F 275F 275F 275F Nylon 180F 275F 275F 275F Polyester 180F 300F 300F 300F Fiberglass 180F 300F 400F 750F

Standard Box Quantities: 10” – 40 per box 20”, 30”, 40”, 50”- 20 per box

Model Code/Ordering Information CARTRIDGE TYPE

MICRON RATING

FILTER MEDIA LENGTH INCHES

CORE TYPE OUT SIDE DIAMETER

OPTIONS SPECIAL

DW- Precision Wound Filter Cartridge

0.5 1 3 5

10 15 20 25 30 50 75

100 125 150 200

01 02 03 04 05 06 09 11 13 14 15 20

-FDA Polypropylene -Fibrillated -Industrial -Ind. (Natural Cotton) -Bleached Cotton -FDA Bleached Cotton-Rayon -Nylon -Polyester -Acrylic -Fiberglass -Anti-Microbial FDA Polypropylene

1 1 1 1 2 2 2 3 3 3 4 5 7

3.75 4 4.755 6 8 9.75 0 2 2.5 9.5 0 4.5 9.25 0 6 9 0 0 2

1 3 4 5 6 7

- Polypropylene-Tinned Steel -304SST -Polyester -316SST -Nylon

A B C D E F G H I J

-2” -2 1/4” -2 3/8” -2 1/2” -2 5/8” -2 3/4” -3” -4” -4 1/4” -4 1/2”

(Big Blue)

2SP – 222 w/ Plug 2SD – 222 w/ Disk 2SF – 222 w/ Fin SPR-Polypro Spring 6SP – 226 w/ Plug 6SD – 226 w/ Disk 6SF – 226 w/ Fin SPR – Polypro Spring E – Extended Core N-Polyester Core Cover EC-End Caps- PVC ECP- Polypro End Caps P-Plug in one end SC- Steel Cap w/Spring

S- Specia

Example: DW-5-05-20-4-C-E, Standard Wound Cartridge , 5 Micron, Bleached Cotton, 20” length, 304 SST Core, 2 3/8” OD, with Extended Core

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118 Fax: (248) 377-3172

[email protected] www.tfsi1.com

127

LIQUID PROCESS FILTRATION - STRINGWOUND AND WATERFILTRATION

CN04 & DCB Series Carbon/Sediment Cartridges

CN04 & DCB Series Carbon/Sediment Cartridges DCB and CN04 cartridges are dual media cartridges which provide removal of chlorine, chemical contamination and sediment. The cartridges also improve the taste and odor of water. The CN04 utilizes an inner carbon impregnated media and the DCB has an extruded activate carbon block center core. The carbon is wrapped with Polypropylene, Bleached cotton or Anti-Microbial Polypropylene media to enhance the life and performance of the carbon. The CN04CF version utilizes a polyester media impregnated with coconut shell carbon which is cellulose free. The CN04CF and DCB are both excellent choices for chemical processing applications such as plating solutions. Benefits

Eliminates requirement for sediment pre-filters

No bypassing, channeling or unloading of carbon fines

Anti-Microbal optional media deters bacteria growth for prolonged carbon effectiveness

DCB offers superior chlorine and VOC removal capacity

Lengths to 40” with fittings available to fit various housings

Applications

Potable and Process Water

Food and Beverage

Chemical Processing

Metal Finishing Processes

Plating Solutions

Odor and Color Removal

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118Fax: (248) 377-3172

[email protected] www.tfsi1.com

128

LIQUID PROCESS FILTRATION - STRINGWOUND AND WATERFILTRATION

CN04 & DCB Series Carbon/Sediment Cartridges

Specifications

Inner Media: DCN: Activated Carbon Block 6 ounces (172 grams) carbon / 10” length CN04: Charcoal Carbon Impregnated Cellulose (CN04) Coconut Carbon Impregnated Polyester (CN04CF) Polypropylene Core 1.5 ounces (43 grams) carbon / 10” length, 2 1/2” OD 4.5 ounces (129 grams) carbon / 10” length, 4 1/2” OD

Outer Media: Standard FDA Grade Polypropylene Optional FDA Bleached Cotton & FDA Anti-Microbial Polypropylene

Lengths: 5 to 40 inches (12.7 to 101.6 mm) * Specialty lengths available

End Caps: Plastisol / PVC / Polypropylene

Temperature Rating: 40 – 150 °F (4.4 – 65.5 °C)

Recommended Max Flow Rate (per 10” length): 3 gpm (11.4 Lpm), 2 1/2” OD 8 gpm (30.3 Lpm), 4 1/2” OD

Recommended Max Change Out Differential Pressure: 25 psid (1.7 bar)

Model Code/Ordering Information

CARTRIDGE TYPE MICRON MEDIA LENGTH OUTSIDE DIAMETER OPTIONS SPECIAL CN04- Activated Carbon Impregnated Cellulose CN04CF- Coconut Shell Carbon Impregnated Polyester DCB- Carbon Block

blank – 1 – 25 – 50 –

5 micron 1 micron 25 micron 50 micron

blank – FDA Polypropylene 06-FDA Bleached Cotton 20 – FDA Antimicrobial Polypropylene

5 – 9 – 10 – 19.5 – 20 – 29.25 – 30 – 40 –

5” 9.75” 10” 19.5” 20” 29.25” 30” 40

Blank – 2 ½” OD J- 4 ½

2SP – 2SD – 2SF – 6SP – 6SD – 6SF – SPR – E –

222 w/ Plug 222 w/ Disk 222 w/ Fin 226 w/ Plug 226 w/ Disk 226 w/ Fin Polypro Spring Extended Core

Blank –S –

none Special

EXAMPLE: CN04 – 20 –F:5 micron, Polypropylene outer media, 20” length, 2 3/4” OD MADE IN USA

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118 Fax: (248) 377-3172

[email protected] www.tfsi1.com

129

LIQUID PROCESS FILTRATION - STRINGWOUND AND WATERFILTRATION

CCB Series Coconut Carbon Block Cartridges

CCB Series Coconut Carbon Block Cartridges Solid carbon block cartridges provide effective removal of bad taste, odor, chlorine, and various other chemical contaminants. These cartridges are made from premium activated coconut shell carbon. The CCB cartridges are compatible with a wide variety of fluids, from potable water to plating solutions. The large carbon surface area ensures optimal chemical and physical absorption of contaminants. CCB Series cartridges also provide fine sediment filtration and are available in lengths up to 40” and 2 1/2” and 4 1/2” diameters. The cartridges are designed to fit standard housings and vessels. Polypropylene end caps and Buna-N gaskets are standard. Benefits Effective at reducing bad taste, odor, chlorine, and VOCs

No bypassing, channeling or unloading of carbon fines

Cartridges are compliant with NSF and FDA

material/processing requirements

Convenient cartridge form

Applications Potable & Process Water

Food & Beverage

Plating Solutions

Industrial Processes

Pre or Post Filter for RO System

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118Fax: (248) 377-3172

[email protected] www.tfsi1.com

130

LIQUID PROCESS FILTRATION - STRINGWOUND AND WATERFILTRATION

CCB Series Coconut Carbon Block Cartridges Model Code/Ordering Information Part Number Length OD Nominal Micron Rating 85% 2PPM Chlorine Reduction Initial Pressure DropCCB-5 5” (127mm) 2 1/2” (63mm) 5um 8,000L @ 3lpm (2113 gal. @ 0.79gpm) 0.12kg/cm2 @ 3lpmCCB-10 9.75” (248mm) 2 1/2” (63mm) 5um 14,000L @ 5lpm (3698 gal. @ 1.32gpm) 0.11kg/cm2 @ 5lpmCCB-20 20” (508mm) 2 1/2” (63mm) 5um 22,000L @ 5lpm (5811 gal. @ 1.32gpm) 0.09kg/cm2 @ 5lpmCCB-30 30” (762mm) 2 1/2” (63mm) 5um 32,000L @ 10lpm (8453 gal. @ 2.64gpm) 0.07kg/cm2 @ 10lpmCCB-40 40” (1016mm) 2 1/2” (63mm) 5um 45,000L @ 20lpm (11887 gal. @ 5.28gpm) 0.05kg/cm2 @ 20lpmCCB-10-J 10” (254mm) 4 1/2” (115mm) 5um 40,000L @ 10lpm (10566 gal. @ 2.64gpm) 0.30kg/cm2 @ 10lpmCCB-20-J 20” (508mm) 4 1/2” (115mm) 5um 82,000L @ 20lpm (21662 gal. @ 5.28gpm) 0.25kg/cm2 @ 20lpm

Specifications

Made with Premium Quality Coconut Shell Activated Carbon

Nominal 5 Micron sediment filtration Standard diameter (2 1/2”) available in 5” to 40”

lengths Big Blue diameter (4 1/2”) available in 10” and

20” lengths Gaskets: Buna-N standard Outer Netting: Polyethylene Maximum Recommended Pressure Drop: 30psid Temperature range: 40F-180F

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118 Fax: (248) 377-3172

[email protected] www.tfsi1.com

131

LIQUID PROCESS FILTRATION - STRINGWOUND AND WATERFILTRATION

DWC Series Carbon Filter Cartridges

DWC Series Carbon Filter Cartridges DWC Series cartridges filters provide removal of chlorine, bad taste and odor, oil and a wide variety of other contaminants. The DWCC cartridges are an economical solution for portable water and other liquids compatible with Cellulose. The DWCF cartridges contain a coconut carbon impregnated polyester media and offer compatibility with a wide range of liquids such as planting solutions. Both contain a rigid Polypropylene core for strength and stability. DWC Series cartridges also provide fine sediment filtration to 5 microns and are available in lengths to 40” and three diameters. Vinyl end caps are standard with optional end fittings available to match assorted housings.

Benefits

Improves Taste and Odor of water

Removal of Impurities

High Dirt-Holding Capacity

Heavy Duty Construction

Low Pressure Drop

Applications

Potable Water

Polishing Filters

Plating Solutions

Industrial Processes

Food and Beverage

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118Fax: (248) 377-3172

[email protected] www.tfsi1.com

132

LIQUID PROCESS FILTRATION - STRINGWOUND AND WATERFILTRATION

DWC Series Carbon Filter Cartridges

Specifications

Media: DWCC: Activated Charcoal Carbon impregnated Cellulose with Polyester Backing 2 1/2” OD: 2.5 ounces of Carbon per 10” length 2 3/4” OD: 4.5 ounces of Carbon per 10” length 4 1/2” OD: 10 ounces of Carbon per 10” length DWCF: Activated Coconut Shell Carbon impregnated Polyester 2 1/2” OD: 2 ounces of Carbon per 10” 2 3/4” OD: 3.6 ounces of Carbon per 10” 4 1/2” OD: 8 ounces of Carbon per 10”

Core: Polypropylene

Netting: Polypropylene

End Caps Polyvinyl / Urethane / Polypropylene

Temperature Rating: DWCC: 40 to 150F (4.4 to 65.5C) DWCF: 40 to 180F (4.4 to 65.5C)

Recommended Max Flow Rates (per 10” length)2 1/2” OD: 2.5 gpm 2 3/4” OD: 3.5 gpm 4 1/2” OD: 8 gpm * Higher flow rates can be employed but removal efficiency may be sacrificed.

Clean Pressure Drop: (based on 10” length): 2 1/2” OD: 3 psi @ 2.5 gpm 2 3/4” OD: 6 psi @ 3.5 gpm 4 1/2” OD: 15 psi @ 8 gpm

Note: Special lengths and diameters are available. Disclaimer: Specifications are subject to change without notice. Made in USA.

Model Code / Ordering Information

CARTRIDGE TYPE

LENGTH INCHES

OUT SIDE DIAMETER

OPTIONS

SPECIAL DWCC - Activated Carbon Impregnated Cellulose DWCF- Coconut Shell Carbon Impregnated Polyester

5 – 4.875” 9 – 9.75” 10 – 10” 19.5 – 19.5” 20 – 20” 29.25 – 29.25” 30 – 30” 40 – 40”

Blank – 2 ½” F – 2 ¾” J – 4 ½”

2SP – 222 w/ Plug 2SD – 222 w/ Disk 2SF – 222 w/ Fin 6SP – 226 w/ Plug 6SD – 226 w/ Disk 6SF – 226 w/ Fin SPR – Polypro Spring E – Extended Core

S- Special

EXAMPLE: DWCC-20-F MADE IN USA

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118 Fax: (248) 377-3172

[email protected] www.tfsi1.com

133

LIQUID PROCESS FILTRATION - STRINGWOUND AND WATERFILTRATION

GPP Series Pleated Filter Cartridges

GPP Series Pleated Filter Cartridges Pleated design offers significantly

increased surface area and flow capacity when compared to depth type cartridges.

Excellent compatibility with a wide range of chemicals and sanitizing agents.

High flow rates with low pressure drops. Cleanable and reusable. Resistant to bacteria attack. Plastisol (PVC) end caps/gaskets offer

positive seal. All cartridges are manufactured with a

polypropylene outer netting. Wide variety of micron ratings (0.35 - 50). Applications

• Process and Potable water

• Food and Beverage

• R.O. Pre-filtration

• Plating Chemicals

• Chemical Solutions

• Wastewater

GPP Series Filter cartridges are produced using 100% synthetic fibers, which are free of binders or adhesives. Each filter is shrink wrapped for purity.

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118Fax: (248) 377-3172

[email protected] www.tfsi1.com

134

LIQUID PROCESS FILTRATION - STRINGWOUND AND WATERFILTRATION

GPP Series Pleated Filter Cartridges

Flow vs Differential Pressure

(water, per 10” length) micron flow (gpm) AP (psid)

2.7” OD 1A 5 1

1 8 1

5 10 0.25

50 10 0.4

1 25 1

4.5” OD 5 25 0.6

50 25 0.3

Performance Specifications Micron Ratings............0.35, 1, 1A, 5, 20, 30, 50 Efficiencies.......90% nominal 1A = 99% absolute

Dimensions Outside Diameter.....................2.7 or 4.5 inches Inside Diameter........................................1 inch Lengths....................................9.75 to 40 inches Outer Netting..............................Polypropylene

Maximum Recommended Operating Conditions Differential Pressure.............................25 PSID Temperature................................140º F (60ºC)

Construction Materials Filtration Media...........Polypropylene/Polyester End Caps/Gaskets.................................Plastisol Core............................................Polypropylene Outer Netting.............................Polypropylene

FDA Listed Materials Manufactured from materials which are listed for food contact applications in Title 21 of the U.S. Code of Federal Regulations.

Model Code/Ordering Information GPP

MICRON RATING

LENGTH (IN)

OUTSIDE DIAMETER (IN)

GPP

0.35

9.75

blank = 2.7 1 19.5 J= 4.5 1A 20 5 29.25 10 30

20 40 30 50

EXAMPLE: GPP-20-20-J NOTE: 4.5” OD only available in 9.75 and 20” lengths

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118 Fax: (248) 377-3172

[email protected] www.tfsi1.com

135

LIQUID PROCESS FILTRATION - ABSOLUTE MELT BLOWNCARTRIDGE

Stratum A Absolute Melt Blown Cartridge

Absolute Rated Melt Blown Filters Stratum A Series melt blown depth filters deliver 99.9% efficiency at the stated micron for the most demanding applications. By utilizing ultra fine fibers and controlled thermal bonding, the Stratum A series retains captured contaminant even at higher differential pressures.

Stratum Series Features – Benefits Absolute retention ratings from 0.5 to 70 microns Multi-zone melt blown depth filter with a graded pore structure for maximum dirt holding capacity Thermally bonded fibers for high void volume and long on-stream life Lot traceable filters come with certificate of conformance 100% polypropylene – FDA listed materials of construction All components meet USP Class VI criteria and are safe for use in pharmaceutical applications Molded center core for higher temperature and pressure capability Free of surfactants, binders and adhesives

Applications Chemicals Paint/Ink Water Plating Pharmaceuticals Food and beverages Microelectronics Cosmetics

Filter Specifications Media: Polypropylene End caps/center core:

Polypropylene

Gaskets/O-rings: Silicone, EPDM, Buna N, Santoprene, Viton and Teflon encapsulated Viton (o-rings only)

Micron ratings: 0.5, 1, 3, 5, 10, 20, 30, 50, 70 Dimensions Nominal lengths: 4, 5, 9.75, 10, 19.5, 20, 29.25, 30,

39, 40 inches (10.2, 12.7, 24.8, 25.4, 49.5, 50.8, 74.3, 76.2, 99.1, 101.6 cm)

Outside diameter: 2.5 in ( 6.35 cm) Inside diameter: 1 in (2.54 cm)

Operating Conditions Maximum differential 1 pressure:

50 psid @ 68°F (10.3 bar @ 20°C)90 psid @ 150°F (6.2 bar @ 66°C) 35 psid @ 176°F (2.4 bar @ 80°C)

Recommended change- out differential pressure:

35 psid (2.4 bar)

Steam Sterilization: Stratum single open end style filters may be autoclaved under no end load conditions for 30 minutes at 121°C. Filters should be cooled to normal operating temperatures prior to use.

Filter Removal Efficiency Micron Rating 99.9% 99% 90% Beta Ratio Beta 1000 Beta 100 Beta 10 0.5 micron 0.6 0.5 0.4 1 micron 1.0 .8 .5 3 micron 3 2.3 1.4 5 micron 5 4.0 2.7 10 micron 10 7 4 20 micron 20 15 12 30 micron 30 20 14 50 micron 50 34 25 70 micron 70 50 39

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118Fax: (248) 377-3172

[email protected] www.tfsi1.com

136

LIQUID PROCESS FILTRATION - ABSOLUTE MELT BLOWNCARTRIDGE

Stratum A Absolute Melt Blown Cartridge

Example: STA 0.5-30NN = Stratum A filter, 0.5 micron, 30 inches, cut ends, No gasket or o-ring

Note: For chemical compatibility, flow rates, and temperature requirements please consult the factory or your local Graver distributor

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118 Fax: (248) 377-3172

[email protected] www.tfsi1.com

137

LIQUID PROCESS FILTRATION - RESIN BONDED CARTRIDGEFulflo® ProBond™ Filter Cartridges A Patented Breakthrough in Resin Bonded Cartridge Design Parker ProBondTM cartridges have a unique, proprietary two-stage filtration design to maximize particle retention and service life in viscous fluid filtration applications. An outer, spiral, pre-filter wrap, made from a fiber blend of polyester and acrylic, increases cartridge strength and eliminates residual debris associated with conventional or machined and grooved, resin bonded cartridges.

ProBond filter cartridges are available in eight differentiated removal ratings of 2μm, 5μm, 10μm, 25μm, 50μm, 75μm, 125μm and 150μm pore sizes to meet a wide range of performance requirements.

Benefits

Outer, spiral wrap collects large particles and agglomerates, while inner layers control particle removal at rated size

Outer wrap increases surface area and eliminates loose debris and contamination caused by machined products

Extra-long acrylic fibers provide added strength, resist breakage and migration common with competitive “short fiber” cartridges

Available with optimal single open-end seals (222 o-ring with flat cap) in ABS or nylon

Phenolic resin impregnation strengthens cartridge for use with high viscosity fluid

Withstands pressure surges up to 150 psid across cartridge (depending on fluid temperature)

One-piece construction eliminates bypass concerns with multi-length cartridges and eases change out

Silicone-free construction ensures no contamination to adversely affect adhesion properties of coatings

Applications

Paints Printing Inks Adhesives Resins Emulsions Chemical Coatings Organic Solvents Plasticizers Waxes Oilfield Fluids Process Water Petroleum Products

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118Fax: (248) 377-3172

[email protected] www.tfsi1.com

138

LIQUID PROCESS FILTRATION - RESIN BONDED CARTRIDGEFulflo® ProBond™ Filter Cartridges

ProBond Flow Factors

Rating (µm)

Flow Factors

2 0.08 5 0.04

10 0.02 25 0.012 50 0.01 75 0.006

125 0.0013 150 0.0010

ProBond Length Factors

Length (in)

Length Factor

9 1.0 10 1.0 19 2.0 20 2.0 29 3.0 30 3.0 39 4.0 40 4.0

Particle Removal Ratings: 2µm, 5µm, 10µm, 25µm, 50µm, 75µm, 125µm and 150µm

Dimensions, in (mm):

Outside Diameter: 2-9/16 in (65) Inside Diameter: 1-1/8 in (28.6) Lengths: Nominal, 10, 20, 30 and 40 in lengths

Environmental/Chemical Compatibility:

Classified as a nonhazardous material Incinerable (8000 BTU/lb) Crushable and shred-able Certified silicone-free Suitable for weak acids and bases (pH 5-9) Unsuitable for oxidizing agents Not recommended for FDA applications

End Adapters: None on double open end style ABS (Acrylonitrile Butadiene Styrene) for most applications Nylon (NTC) for aromatic solvents

Flow Rate and Pressure Drop Formulas Flow Rate (gpm) = Clean P x Length Factor Viscosity x Flow Factor

Clean DP = Flow Rate x Viscosity x Flow Facto Length Factor 1. Clean P is PSI differential at start. 2. Viscosity is centistokes. use conversion

Tables for other units. 3. Flow Factor is P/GPM at 1 cks for 10 in (or single). 4. Length Factors convert flow or P from 10

in (single length) to required cartridge length.

Specifications

Materials of Construction: 1st stage Pre-filter wrap: Polyester/Acrylic long staple fiber blend 2nd stage Final Filter wrap: Acrylic long staple fiber Fibers impregnated with Phenolic Resin Type of Construction: Coreless, one-piece, rigid resin bonded fibrous matrix

Maximum Recommended Operating Conditions:

Flow Rate: 5 gpm per 10 in length (18.9 lpm per 254 mm length) Temperature: 250F (121C) Maximum Recommended Change Out P: 50 psid (3.5 bar) Recommended Maximum Differential Pressure: Cartridge Pressure Resistance: 150 psid (10 bar) @ 70F (21C) 125 psid (8.6 bar) @ 100F (38C) 90 psid (6.2 bar) @ 150F (65C) 65 psid (4.5 bar) @ 180F (82C) 25 psid (1.7 bar) @ 250F (121C)

____________________________________________________________________________________________

Ordering Information

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118 Fax: (248) 377-3172

[email protected] www.tfsi1.com

139

LIQUID PROCESS FILTRATION - PLEATED NOMINAL CARTRIDGEGFC Microfiberglass - Pleated Nominal CartridgeGlass Fiber Cartridges (GFC) This high efficiency, disposable filter element is suited for a wide range of applications. The filter is constructed of pleated Borosilicate Microfiberglass filter media with greater surface area for high system flow rate.

Filter Features–Benefits Micron ratings from 0.2 to 30 m– Broad application range Uniform pore size– High removal efficiency High surface area– High flow capability and dirt holding

capacity Long service life– Minimizes maintenance costs Fixed pore construction– Eliminates dirt unloading at

maximum differential pressure

Filter Specifications Filter Removal Efficiency Media: Borosilicate Microfiberglass with Acrylic Binder

Beta Ratio Beta 10 Beta 20 Beta 100 Beta 1000 Beta 5000 Efficiency 90% 95% 99% 99.9% 99.98%

Inner core: Polypropylene 0.2 micron 0.2 0.3 0.6 0.8 1.0 Support layers: Polyester 0.45 micron 0.45 0.6 0.8 1.8 2.0 End caps: Polypropylene 1.0 micron 1.0 1.3 2.0 3.5 4.0 Cage: Polypropylene 3.0 microns 3.0 4.0 5.5 9.0 10.0

10.0 micron 10.0 12.0 15.0 17.0 18.0 Gasket/O-Rings : Buna-N, EPDM, Silicone, Teflon Encapsulated Viton O-Rings 30.0 microns 30.0 35.0 38.0 42.0 45.0

Micron ratings: 0.2, 0.45, 1.0, 3.0, 10, 30 m Dimensions and Operating Parameters Nominal lengths: 9.75’’ 10’’, 20’’, 30’’, 40’’ (24.7, 25.4, 50.8, 76.2, 101.6 cm) Outside diameter: 2.7’’ (6.9 cm) Inside diameter: 1.0’’ (2.54 cm) Maximum operating temperature: 176 °F (80°C)

Maximum 80 psid @ 70 °F (5.5 bar @ 21°C) differential pressure: 40 psid @ 150 °F (2.8 bar @ 65°C)

Beta Ratio = Upstream particle counts Downstream particle counts

The micron ratings shown at various efficiency and beta ratio value levels were determined through laboratory testing, and can be used as a guide for selecting cartridges and estimating their performance. Under actual field conditions, results may vary somewhat from the values shown due to the variability of filtration parameters. Testing was conducted using the single-pass test method, water at 2.5 gpm/10’’ cartridge. Contaminants included latex beads, coarse and fine test dust. Removal efficiencies were determined using dual laser source particle counters.

Applications Wine pre-filtration Blowdown post filter Magnetic tape coatings

Chemicals Inks Oil & Gas

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118Fax: (248) 377-3172

[email protected] www.tfsi1.com

140

LIQUID PROCESS FILTRATION - PLEATED NOMINAL CARTRIDGEGFC Microfiberglass - Pleated Nominal Cartridge

Example: GFC 3-10P7B-I = GFC filter, 3 micron, 10 inches, 226/Fin, Buna-N O-Rings, end cap insert for steaming

* For liquids other than water, multiply pressure drop by fluid viscosity in centipoises 0.2

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118 Fax: (248) 377-3172

[email protected] www.tfsi1.com

141

LIQUID PROCESS FILTRATION - PLEATED NOMINAL CARTRIDGEPMC Polypropylene - Pleated Nominal Cartridge

“Absolute” Rated Pleated Filter Cartridges This all polypropylene filter retains particles with absolute efficiency. Available in a broad range of pore sizes, it is suitable for a wide range of applications. The pleated construction provides a high surface area to offer outstanding overall filtration economy. Filter Features–Benefits Micron ratings from 0.2 to 100 μm– Broad application range Meets current USP Class VI biological test for plastics–

Acceptable for food & beverage contact “Absolute” Efficiency–Rated at 99.98% (Beta 5000) Competitive surface area– High flow rates, and long on-line

service– Minimize maintenance cost Fixed pore structure– Eliminates dirt unloading at maximum differential pressure Polypropylene Construction– Inert to many process fluids Various Gasket/O-Ring materials– Compatible with a variety

of fluids Manufactured in continuous lengths up to 40 inches

Filter Specifications

Filter Removal Efficiency Media: Polypropylene Beta Ratio Beta 5000 Beta 100 Beta 50 Inner core: Polypropylene

Efficiency 99.98% 99% 98%

End caps: Polypropylene 0.2 micron 0.20 0.10 0.05 Cage: Polypropylene 0.45 micron 0.45 0.30 0.20

1.0 micron 1.0 0.60 0.30 Gaskets/O-Rings: Buna-N, EPDM, Silicone, Viton, Teflon Encapsulated Viton

2.5 microns 2.5 2.0 1.5

(O-Rings only) 5.0 microns 5.0 4.0 3.0 Polypropylene 0.2, 0.45, 1.0, 2.5, 5.0, 10, 25, 10.0 microns 10.0 8.0 7.0 micron ratings: 50, 100μm

25.0 microns 25.0 19.0 15.0 Dimensions and Operating Parameters 50.0 microns 45.0 35.0 28.0 Nominal lengths: 9.75’’ 10’’, 20’’, 30’’, 40’

100.0 microns – 100.0 85.0

(24.7, 25.4, 50.8, 76.2, 101.6 cm) Outside diameter: 2.7’’ (6.86 cm)

Inside diameter: 1.1’’ (2.79 cm) Maximum operating Temperature: 176 °F (80 °C)

Maximum 75 psid @ 70 °F (5.2 bar @ 21°C) differential pressure: 40 psid @ 176 °F (2.8 bar @ 80°C)

Recommended change- out pressure for disposal:35 psid (2.4 bar)

FDA Compliance All polypropylene material used in manufacturing complies with the regulations of the Food and Drug Administration (FDA) title 21 of the Code of Federal Regulations Sections 174.5, 177.1520, and 177.1630, as applicable for food and beverage contact.

Upstream particle counts Beta Ratio =Downstream particle counts

The micron ratings shown at various efficiency and beta ratio value levels were determined through laboratory testing, and can be used as a guide for selecting cartridges and estimating their performance. Under actual field conditions, results may vary somewhat from the values shown due to the variability of filtration parameters. Testing was conducted using the single-pass test method, water at 3gpm/10'' cartridge. Contaminants included latex beads, coarse and fine test dust. Removal efficiencies were determined using dual laser source particle counters.

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118Fax: (248) 377-3172

[email protected] www.tfsi1.com

142

LIQUID PROCESS FILTRATION - PLEATED NOMINAL CARTRIDGEPMC Polypropylene - Pleated Nominal Cartridge

Example: PMC 2-20 P8V

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118 Fax: (248) 377-3172

[email protected] www.tfsi1.com

143

LIQUID PROCESS FILTRATION - PLEATED NOMINAL CARTRIDGEQCR Cyst Reduction - Pleated Nominal Cartridge

Health Dangers of Cryptosporidium In recent years, significant outbreaks of water borne disease have been traced to Cryptosporidium and Giardia parasites. These naturally occurring organisms are present in many surface water sources and are highly resistant to inactivation by conventional water treatment processes such as chlorination. Healthy individuals typically recover from the common gastrointestinal effects within a few weeks, however for individuals with weakened or undeveloped immune systems, it can be life threatening.

In order to ensure the safety of the water supply, standard have been established that define the minimum performance requirements for materials and components of water treatment systems. The QCR Cyst Reduction filter contains an absolute 1micron filter media designed to exceed the ANSI/NSF Standard 53 of 99.95% for the removal of cysts based upon the polystyrene challenge in water*.

Filter Specifications

Materials

Media: Polypropylene

Core/cage: Polypropylene

End caps: Polypropylene

O-Rings: Silicone O-Ring (other materials optional)

Filter Connections

P2 (226/flat), P3 (222/flat), P7 (226/fin), P8 (222/fin)

Dimensions

Nominal lengths: 9.75”, 10’’, 20’’, 30’’, 40’’ 25.4, 50.8, 76.2, 101.6 cm)

Outside diameter: 2.7’’ (6.9 cm)

Inside diameter: 1.0’’ (2.54 cm)

Maximum operating temperature: 176°F (80°C)

Filter Features–Benefits Constructed entirely of polypropylene Compatible with

most solutions 7.7 ft2(0.72 m2) of effective filter area High flow rates at low pressure drop High dirt capacity Meets/exceeds NSF Standard 53 for cyst reduction* Various O-Ring materials and configurations Easily retrofits most systems High surface area High flow rates and long on-line service Meets USP Class VI Biological Test for plastic FDA Listed Materials All polypropylene material used in manufacturing complies with the regulations of the Food and Drug Administration (FDA) Title 21 of the Code of Federal regulations 174.5,177.1520 and 177.1630, as applicable for food and beverage contact. *Performance tested and verified by Independent Laboratory Testing

Maximum differential 75 psid @ 70°F (5.2 bar @ 21°C) pressure: 40 psid @ 176°F(2.8 bar @ 80°C) 15 psid @ 190°F (1.03 bar @ 88°C)

Recommended 35 psid (2.4 bar) change-out:

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118Fax: (248) 377-3172

[email protected] www.tfsi1.com

144

LIQUID PROCESS FILTRATION - PLEATED NOMINAL CARTRIDGEQCR Cyst Reduction - Pleated Nominal Cartridge

Example: QCR 1-30 P7VNote: DOE style filters not offered in the QCR product. Cyst reduction claim not valid for DOE style filters per NSF standard 53, for bottled water facilities.

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118 Fax: (248) 377-3172

[email protected] www.tfsi1.com

145

LIQUID PROCESS FILTRATION - PLEATED NOMINAL CARTRIDGEQMC Polypropylene - Pleated Nominal Cartridge

High Efficiency Polypropylene Filter Cartridge An innovative product manufactured with multiple layers of melt-blown polypropylene media. This unique structure allows high flow rates while maintaining low differential pressure and ideal depth filtration characteristics.

Filter Features–Benefits Micron ratings from 0.1 to 10 μm– Broad application range Meets current USP Class VI biological test for plastics FDA listed materials of construction High Filtration Efficiency – 95% Graded pore structure – Multilayer, media for high dirt holding

capacity Fixed pore construction – Resists dirt unloading at maximum

differential pressure Polypropylene construction – Inert to many process fluids Various Gasket/O-ring materials – Compatible with many fluids

Filter Specifications Filter Removal Efficiency Construction material: Polypropylene Gasket/O-Rings: Buna-N, EPDM, Silicone, Viton, Teflon

Beta Ratio Beta 100 Beta 20 Efficiency 99% 95%

Encapsulated Viton (O-Rings only) 0.1 micron 0.8 0.1 Micron ratings: 0.1, 0.2, 0.4, 0.6, 1.0, 3.0, 5.0, 10.0μm 0.2 micron 1.0 0.2

Dimensions and Operating Parameters 0.4 micron 2.0 0.4 Parameters Nominal 9.75’’, 10’’, 20’’, 30’’, 40’’ 0.6 micron 3.0 0.6 lengths: (24.8, 25.4, 50.8, 76.2, 101.6 cm) 1.0 micron 6.0 1.0

Outside diameter: 2.7’’ (6.9 cm) 3.0 micron 14 3.0 Inside diameter: 1.0’’ (2.54 cm) 5.0 microns 17 5.0

10.0 microns 25 10.0 Maximum operating temperature: 176 °F (80°C)

Performance Specifications Maximum 80 psid @ 70°F(5.5 bar @ 21°C) differential pressure: 40 psid @ 176°F (2.8 bar @ 80°C) Maximum reverse differential pressure: 40 psid @ 70°F (2.8 bar @ 21°C) Recommended Changeout pressure: 35 psid (2.4 bar)

Applications

Sanitization Hot water at 176°F(80°C) at 5 psid (0.35 bar) for 30 min. In-line steam at 257°F (125°C) at 1psid (0.07 bar) for 30 min. Autoclavable at 257°F (125°C) for 30 min. FDA Listed Materials All materials comply with FDA title 21 of the Code of Federal Regulations as applicable for food and beverage contact.

Food & beverage Aqueous solutions Pharmaceuticals Ultra pure water

RO Pre-filters Chemicals Cosmetics Ink

DE trap Photo resists

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118Fax: (248) 377-3172

[email protected] www.tfsi1.com

146

LIQUID PROCESS FILTRATION - PLEATED NOMINAL CARTRIDGEQMC Polypropylene - Pleated Nominal Cartridge

Example: QMC 0.6-10 P2T

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118 Fax: (248) 377-3172

[email protected] www.tfsi1.com

147

LIQUID PROCESS FILTRATION - PLEATED NOMINAL CARTRIDGEHigh Flow - Pleated Nominal Cartridge

Large Geometry Pleated Filters for High Flow

Graver High Flow Series filters feature a larger geometry to handle higher flows with fewer filter elements. The result is much faster, easier filter change outs. In addition, the inside to outside flow allows for excellent dirt holding capacity, extending the time between filter changeouts. Filter housings are also available and because of the filters high flow and dirt holding capacity, smaller systems are possible, reducing upfront capital costs.

High Flow Series Features – Benefits 6” diameter, large geometry for high flows Absolute retention ratings from 1 to 100 microns Capable of flow rates up to 500 GPM in a single 60” element FDA listed materials of construction Inside-out flow retains contaminant even during changeout Multi layer pleated construction with optimized surface area Outer cage prevents media extrusion problem experienced with

some competitive offerings Unique Quad Seal gasket provides maximum seal integrity Retrofits competitive high flow filter housings Thermally bonded construction.

Filter Specifications Applications Media/Support/Cage: Polypropylene End caps: Polypropylene Gaskets/O-rings: EPDM, Silicone, Buna N, Viton

Water Systems Chemicals Food and Beverage

Micron ratings: 1, 3, 5, 10, 20, 40, 60, 100

Dimensions Filter Removal Efficiency Nominal lengths: 20, 40, 60 inches Beta Ratio Beta 1000 Beta 100 Beta 10 (50.8, 101.6, 152.4 cm) Micron Rating 99.9% 99% 90% Outside diameter: 6.0 in (15.2 cm)

1 micron 1 0.6 0.2

Operating Conditions 3 micron 3 2 1.5 Maximum operating 180°F@ 20psid (82°C @1.4 bar)

5 micron 5 4 3

10 micron 10 8.5 6.5 160°F@ 30psid (71°C @2.1 bar) 77°F @ 50psid (25°C @ 3.4 bar)

20 micron 22 19 14

40 micron 38 18 15 Recommended changeout differential pressure: 35psid (2.4 bar)

60 micron 60 35 20

Maximum flow rates: 60” element up to 500 GPM 1892 lpm) 100 micron 100 75 45 40” element up to 350 GPM (1325 lpm)

20” element up to 175 GPM (662 lpm)

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118Fax: (248) 377-3172

[email protected] www.tfsi1.com

148

LIQUID PROCESS FILTRATION - PLEATED NOMINAL CARTRIDGEHigh Flow - Pleated Nominal Cartridge

Example: HF 5-60E = High Flow filter, 5 micron, 60 inches, EPDM

High Flow Series Element Pressure Drop Element Pressure Drop psid/gpm Element Pressure Drop Mbar/M3/Hr) 20" 40" 60" 20" 40" 60" 1 0.0200 0.0097 0.0065 6.0845 2.9395 1.9820 3 0.0167 0.0081 0.0054 5.0705 2.4495 1.6516 5 0.0076 0.0037 0.0025 2.3179 1.1198 0.7550

10 0.0046 0.0022 0.0015 1.3908 0.6719 0.4530 20 0.0021 0.0010 0.0007 0.6374 0.3079 0.2076 40 0.0017 0.0008 0.0006 0.5215 0.2520 0.1699 60 0.0015 0.0007 0.0005 0.4552 0.2199 0.1483 100 0.0010 0.0005 0.0003 0.3035 0.1466 0.0989

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118 Fax: (248) 377-3172

[email protected] www.tfsi1.com

149

LIQUID PROCESS FILTRATION - PLEATED NOMINAL CARTRIDGESteris® Replacement Filters - Pleated Nominal Cartridge Graver Technologies’ replacement A and B filters, for Steris machines offer excellent protection for the final sterile filter.

Replacement A & B filters are designed to effectively protect and extend the life of the final sterile filter

Choice of end cap styles to fit your housings Meets FDA Standards – All material used in the

construction of the filters meets FDA (Food and Drug Administration) Title 21 of the CFR

Clean manufacturing process is used which eliminates the use of glues or epoxies

End caps are thermo-bonded to the media and support hardware

High dirt holding capacity Longer on-line service reduces valuable maintenance

time Fixed pore construction eliminates dirt unloading or

fiber releasing

Configuration Options Part Number Description “A” Filter FPLGT00100 Double open end with silicone flat gasket seal. F801030000 Single open end with internal 214 silicone O-ring. Recessed cup on closed end to fit over housing post.

“B” Filter FPLGT00200 Single open end with 2-222 silicone O-rings. Flat cap on closed end. F80D000013 Single open end with 2-222 EPR O-rings. Recessed cup on closed end to fit over housing post.

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118Fax: (248) 377-3172

[email protected] www.tfsi1.com

150

LIQUID PROCESS FILTRATION - PLEATED NOMINAL CARTRIDGESteris® Replacement Filters - Pleated Nominal Cartridge Steris Replacement Filter Specifications

All information and recommendations appearing in this bulletin concerning the use of products described herein are based on tests believed to be reliable. However, it is the user’s responsibility to determine the suitability for his own use of such products. Since the actual use by others is beyond our control, no guarantee, expressed or implied, is made by Graver Technologies as to the effects of such use or the results to be obtained. Graver Technologies assumes no liability arising out of the use by others of such products. Nor is the information herein to be construed as absolutely complete, since additional information may be necessary or desirable when particular or exceptional conditions or circumstances exist or because of applicable laws or government regulations. Steris is a registered trademark of Steris Corporation.

For more information about Steris Replacement Filters or about any other high performance filtration products, contact your local Distributor:

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118 Fax: (248) 377-3172

[email protected] www.tfsi1.com

151

LIQUID PROCESS FILTRATION - PLEATED ABSOLUTE CARTRIDGEPMA Polypropylene - Pleated Absolute Cartridge“Absolute” Rated Pleated Filter Cartridges This all polypropylene filter retains particles with absolute efficiency. Available in a broad range of pore sizes, it is suitable for a wide range of applications. The pleated construction provides a high surface area to offer outstanding overall filtration economy. Filter Features–Benefits Micron ratings from 0.2 to 100 μm– Broad application range Meets current USP Class VI biological test for plastics –

Acceptable for food & beverage contact “Absolute” Efficiency– Rated at 99.98% (Beta 5000) Competitive surface area– High flow rates, and long on-line

service– Minimize maintenance cost Fixed pore structure– Eliminates dirt unloading at maximum

differential pressure Polypropylene Construction– Inert to many process fluids Various Gasket/O-Ring materials– Compatible with a variety

of fluids Manufactured in continuous lengths up to 40 inches| Filter Specifications

Filter Removal Efficiency Media: Polypropylene Inner core: Polypropylene

Beta Ratio Beta 5000 Beta 100 Beta 50 Efficiency 99.98% 99% 98%

End caps: Polypropylene 0.2 micron 0.20 0.10 0.05 Cage: Polypropylene 45 micron 0.45 0.30 0.20 Gaskets/O-Rings: Buna-N, EPDM, Silicone, Viton, 1.0 micron 1.0 0.60 0.30

2.5 microns 2.5 2.0 1.5 Teflon Encapsulated Viton (O-Rings only) 5.0 microns 5.0 4.0 3.0 Polypropylene 0.2, 0.45, 1.0, 2.5, 5.0, 10, 25,

10.0 microns 10.0 8.0 7.0 micron ratings: 50, 100μm 25.0 microns 25.0 19.0 15.0 Dimensions and Operating Parameters

50.0 microns 45.0 35.0 28.0

Nominal lengths: 9.75’’ 10’’, 20’’, 30’’, 40’ 100.0 microns – 100.0 85.0 (24.7, 25.4, 50.8, 76.2, 101.6 cm) Outside diameter: 2.7’’ (6.86 cm)

Upstream particle counts Beta Ratio =

Downstream particle counts Inside diameter: 1.1’’ (2.79 cm) Maximum operating Temperature: 176 °F (80 °C)

Maximum 75 psid @ 70 °F (5.2 bar @ 21°C) differential pressure: 40 psid @ 176 °F (2.8 bar @ 80°C)

Recommended change- out pressure for disposal:35 psid (2.4 bar)

FDA Compliance All polypropylene material used in manufacturing complies with the regulations of the Food and Drug Administration (FDA) title 21 of the Code of Federal Regulations Sections 174.5, 177.1520, and 177.1630, as applicable for food and beverage contact.

The micron ratings shown at various efficiency and beta ratio value levels were determined through laboratory testing, and can be used as a guide for selecting cartridges and estimating their performance. Under actual field conditions, results may vary somewhat from the values shown due to the variability of filtration parameters. Testing was conducted using the single-pass test method, water at 3gpm/10'' cartridge. Contaminants included latex beads, coarse and fine test dust. Removal efficiencies were determined using dual laser source particle counters.

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118Fax: (248) 377-3172

[email protected] www.tfsi1.com

152

LIQUID PROCESS FILTRATION - PLEATED ABSOLUTE CARTRIDGEPMA Polypropylene - Pleated Absolute Cartridge

Example: PMA 2.5-10 PV

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118 Fax: (248) 377-3172

[email protected] www.tfsi1.com

153

LIQUID PROCESS FILTRATION - PLEATED ABSOLUTE CARTRIDGEQMA Polypropylene - Pleated Absolute Cartridge

“Absolute” Rated High Performance Pleated Polypropylene Filter Cartridge This filter is constructed with a high surface area melt-blown polypropylene media for low initial pressure drop, high dirt holding capacity, and high efficiency performance.

Filter Features–Benefits Micron ratings from 0.2 to 100 μm– Broad application

range Meets current USP Class VI biological test for plastics “Absolute” Efficiency– Rated at 99.98% (Beta 5000) High surface area– High flow rates, and long service life – Minimize maintenance cost. Fixed Pore construction – Resists dirt unloading at

maximum differential pressure Polypropylene Construction – Inert to many process fluids Various Gasket/O-ring materials – Compatible with many

fluids Heavy-duty molded cage – High structural strength Highly consistent melt-blown media for consistent

performance

Filter Specifications

Filter Removal Efficiency Construction material: Polypropylene Gaskets/O-Rings: Buna-N, EPR, Silicone, Viton, Teflon Encapsulated Viton

Beta Ratio Beta 5000 Beta 100 Beta 50 Efficiency 99.98% 99% 98% 0.2 micron 0.20 0.10 0.05

(O-Rings only) 0.45 micron 0.45 0.30 0.20 Micron ratings: 0.2, 0.45, 1.0, 2.5, 5.0, 10, 20μm 1.0 micron 1.0 0.60 0.30 Dimensions and Operating Parameters 2.5 microns 2.5 2.0 1.5

5.0 microns 5.0 4.0 3.0 Nominal lengths: 9.75’’ 10’’, 20’’, 30’’, 40’’ (24.7, 25.4, 50.8, 76.2, 101.6 cm)

10.0 microns 10.0 8.0 7.0

Outside diameter: 2.7’’ (6.86 cm) 20.0 microns 20.0 17.0 15.0 Inside diameter: 1.0’’ (2.54 cm)

Surface area: up to 7.0 ft2 Upstream particle counts

Beta Ratio = Downstream particle counts

Maximum operating

temperature: 176°F (80°C) Maximum differential 75 psid @ 70°F (5.2 bar @ 21°C) Pressure: 40 psid @ 176°F (2.8 bar @ 80°C)

FDA & USP Compliance All polypropylene material used in manufacturing complies with the regulations of the Food and Drug Administration (FDA) title 21 of the Code of Federal Regulations Sections 174.5, 177.1520, and 177.1630, as applicable for food and beverage contact

The micron ratings shown at various efficiency and beta ratio value levels were determined through laboratory testing, and can be used as a guide for selecting cartridges and estimating their performance. Under actual field conditions, results may vary somewhat from the values shown due to the variability of filtration parameters.

Testing was conducted using the single-pass test method, water at 2.5gpm/10'' cartridge. Contaminants included latex beads, coarse and fine test dust. Removal efficiencies were determined using dual laser source particle counters.

Applications Food & beverage

Bottled water Process water

Aqueous solutions Pharmaceutical RO Pre-filters

Chemicals Cosmetics Ink

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118Fax: (248) 377-3172

[email protected] www.tfsi1.com

154

LIQUID PROCESS FILTRATION - PLEATED ABSOLUTE CARTRIDGEQMA Polypropylene - Pleated Absolute Cartridge

Example: QMA 1-20 P3V-R-I

Performance Specifications Sanitization Hot water at 176°F (80°C) at 5 psid (0.35 bar) for 30 min. In-line steam at 257°F (125°C) at 1psid (0.07 bar) for 30 min. Autoclavable at 257°F (125°C) for 30 min.

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118 Fax: (248) 377-3172

[email protected] www.tfsi1.com

155

LIQUID PROCESS FILTRATION - PLEATED ABSOLUTE CARTRIDGEQXL Polypropylene - Pleated Absolute Cartridge

Absolute Rated Filtration for Inks, Slurries and Coatings With its extra-loft, extra-life depth filter configuration, the QXL is designed for the filtration of industrial solutions containing agglomerated particles and gels or with high viscosity. Consistent absolute retention performance is achieved throughout the pleated, serialized microfiber matrix. The state-of-the-art optimized structure provides significantly higher flow rates and throughputs than cylindrical melt blown filters.

Filter Features–Benefits Hybrid pleated depth construction combines graded pore

structure with high surface area. Constructed entirely of polypropylene – Compatible with a

broad range of solutions and chemicals Optimized pleat configuration – Provides the ideal combination

of retention, flow rate and throughput Excellent gel and agglomerated particle retention reduces defects Available in common end cap configurations – Retrofits easily

into most filter housings FDA listed materials of construction Meets USP Class VI Biological test for plastics

Filter Specifications Materials

Applications

Media: Polypropylene Core, Cage, End Caps: Polypropylene Gaskets/O-Rings: Silicone, Viton, EPDM, Buna, Teflon

Inks Paints

CMP P-O-U and bulk slurries Beverages

Adhesives Coatings

encapsulated Viton (O-Rings only) Filter Removal Efficiency Micron Ratings: 0.45, 0.5, 1, 3, 5, 10, 20, 40 μm Dimensions and Operating Parameters

Beta Ratio Beta 1000 Beta 100 Beta 50 Efficiency 99.9% 99% 98%

Typical nominal lengths: 9.75", 10", 20", 30", 40" 0.45 micron 0.45 0.3 0.2 24.8, 25.4, 50.8, 76.2, 101.6 cm 0.5 micron 0.65 0.45 0.3 Outside Diameter: 2.7" (6.86 cm) 1 micron 1.5 0.8 0.6 Inside Diameter: 1.1" (2.79 cm) 3 microns 3 2 1

Maximum Operating 5 microns 5 4 3 Temperature: 176°F (80°C) 10 microns 10 8 7

20 microns 20 19 17 Maximum 75 psid @ 70°F (5.2 bar @ 21°C) Differential Pressure: 40 psid @ 176°F (2.8 bar @ 80°C) 40 microns 40 35 25

Maximum Reverse Differential Pressure: 35 psid @ 80°F (2.4 bar @ 27°C)

Recommended Change-out pressure: 35 psid (2.43 bar)

Sterilization: Cartridges may be autoclaved for 30minutes at 250°F(121°C) under no end load conditions. May be in-line sanitized with 185°F (85°C) hot water– do not exceed 3 psid.

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118Fax: (248) 377-3172

[email protected] www.tfsi1.com

156

LIQUID PROCESS FILTRATION - PLEATED ABSOLUTE CARTRIDGEQXL Polypropylene - Pleated Absolute Cartridge

Example: QXL 5-10 P8S

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118 Fax: (248) 377-3172

[email protected] www.tfsi1.com

157

LIQUID PROCESS FILTRATION - PLEATED ABSOLUTE CARTRIDGEClaripor™ Filter Cartridges Polypropylene Pleated Depth Media for Critical Process Applications

The best of pleated and depth style technologies combine in Parker’s ClariporTM pleated depth filter cartridges. The unique layered construction provides absolute retention with high flow rates and excellent gel removal. These features, in addition to ClariporTM’s high contaminant holding capacity and exceptional clarifying ability, make it an ideal choice for a wide array of critical process applications.

ClariporTM cartridges are available with polypropylene media in absolute (99.98%) micron ratings from 0.5 to 90 microns. Benefits

Pleated construction yields high flow rates compared to traditional depth filters

Rigid cage design permits superior strength Graded density layering for superior removal of

amorphous particles Available with all industry standard end configurations Absolute retention ratings for critical filtration All materials listed as acceptable for potable and edible

contact according to CFR Title 21 Manufactured with strict quality control Parker Process Filtration division is an ISO9001:2000

registered company

Applications

Critical coatings Inkjet inks Specialty chemicals

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118Fax: (248) 377-3172

[email protected] www.tfsi1.com

158

LIQUID PROCESS FILTRATION - PLEATED ABSOLUTE CARTRIDGEClaripor™ Filter Cartridges Specifications Materials of Construction Media: Polypropylene Support/Drainage: Polypropylene Hardware: Polypropylene O-Rings (SOE): EPR, Buna-n, Viton*, Silicone, PFA Encapsulated Viton* Gaskets (DOE): EPR, Buna-n, Viton*, Silicone

Recommended Operating Conditions Flow Rate: 5 gpm (18.9 lpm) per 10” equivalent Change-out Pressure: 35 psid (2.4 bar) Retention Ratings (99.98%): 0.5, 1.5, 3, 4.5, 10, 20, 30, 40, 70, 90µm Maximum Operating Conditions Maximum Temperature: 176°F (80° C) @ 30 psid (2.1 bar) Maximum Differential Pressure: 70 psi (4.8 bar) @ 77°F (25° C) 30 psi (2.1 bar) @ 176°F (80° C) Dimensions (nominal) Outside Diameter: 2.7" (6.86 cm) Inside Diameter: 1” (2.54 cm)

Performance Attributes

Flow rate vs. DP for a 1 cks liquid @ 73°F (23° C)**

____________________________________________________________________________ Ordering Information

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118 Fax: (248) 377-3172

[email protected] www.tfsi1.com

159

LIQUID PROCESS FILTRATION - PLEATED ABSOLUTE CARTRIDGEGlass-Mate™ Cartridges Absolute and economical filtration with pleated micro-fiberglass cartridges

Parker’s Glass-MateTM cartridges offer an economical choice for absolute-rated efficiency, high flow rate capability and long service life. A wide variety of construction components, end fittings and seal options make this product line ideal for pre-filtration and point-of-use filtration for many industrial applications.

Glass-Mate cartridges are available in 0.45, 1, 2, 3, 5, 10, 20 and 40μm absolute-rated pore sizes. Benefits

Absolute-rated media provides reliable removal efficiency Thermal bonding eliminates particle bypass Laminated media/support layer maximizes flow capacity and

media utilization and minimizes media migration Variety of construction/seal options for increased

compatibility End fitting options provide competitive housing retrofit

capability All FDA listed components bio-safe per USP Class V1-121° C

Plastic Tests allows filtration of edible and potable liquids High surface area yields high flow rate, low differential

pressure Non-fiber-releasing media with minimal extractables provides

high purity filtrate

Applications

Chemicals Coatings Water R.O. pre-filtration

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118Fax: (248) 377-3172

[email protected] www.tfsi1.com

160

LIQUID PROCESS FILTRATION - PLEATED ABSOLUTE CARTRIDGEGlass-Mate™ Cartridges Specifications

Materials of Construction: Filter Medium: Borosilicate micro-fiberglass with acrylic binder Support/Drainage Layers: Spunbonded polyester; laminated on the downstream side

Recommended Operating Conditions: Maximum Temperatures

Glass Filled Polypropylene 200°F @ 35P (93°C/2.4 bar) Polyester 140°F @ 35P (60°C/2.4 bar) Stainless Steel 275°F @ 35P (135°C/2.4 bar) Changeout Differential Pressure 35 psi (2.4 bar) Maximum Flow Rate 10 gpm per 10 in length (38 lpm/254 mm) Design Flow Rate 2.5 gpm per 10 in length (9.5 lpm/254 mm)

Effective Filtration Area: 5 ft2/10 in (0.46 m2/254 mm) minimum Maximum Differential Pressure: Glass-Filled Polypropylene 90 psi @ 75°F (6.2 bar/24°C) Polyester 70 psi @ 75°F (4.8 bar/24°C) Biological safety/Product Purity: Meets USP XXIV class VI safety requirements for plastics All components FDA listed per CFR, Title 21 Non-fiber releasing per FDA Sterilization/Sanitization: Hot water (“F” construction): 180°F (82°C) for 30 minutes at maximum 15 psid (1 bar). In-Line Steam/Autoclave (“F” construction with stainless steel sleeve) 60 minutes at 255°F (140°C) at 2 psid (0.14 bar) maximum pressure.

Glass-Mate flow factor (psid/gpm @ 1 cks)

Rating (µm)

Flow Factor

0.45 .108 1 .102 2 .095 3 .090 5 .072 10 .060 20 .042 40 .018

Flow Rate and Pressure Drop Formulas Flow rate (gpm) = Clean P x Length Factor Viscosity x Flow Factor

Clean P = Flow rate x viscosity x Flow Factor Length Factor Notes: 1. Clean P is PSI differential at start. 2. Viscosity is centistokes. use conversion Tables for other units. 3. Flow Factor is P/GPM at 1 cks for 10 in (or single). 4. Length Factors convert flow or P from 10 in

(single length) to required cartridge length. Liquid Particle Retention Ratings (µm)@ Removal Efficiency of:

Cartridge ß = 5000 Absolute

ß = 1000 99.9%

ß = 100 99%

ß = 20 95%

ß = 10 90%

PMG004 0.45 0.3 <0.1 <0.1 <0.1 PMG010 1.0 0.6 0.2 <0.1 <0.1 PMG020 2.0 1.2 0.4 0.2 0.1 PMG030 3.0 1.8 0.6 0.3 0.2 PMG050 5 3 1.3 0.5 0.4 PMG100 10 7 3.5 1.6 1.2 PMG200 20 16 8 4 2.5 PMG400 40 32 20 11 8

Ordering Information

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118 Fax: (248) 377-3172

[email protected] www.tfsi1.com

161

LIQUID PROCESS FILTRATION - PLEATED CELLULOSIC CARTRIDGEFulflo® PCC Filter Cartridge Unique Cartridge Construction Improves Particle Retention, Service Life and Flow Rates Parker Fulflo Pleated Cellulosic Cartridges meet a broad range of critical filtration applications. Each cartridge in the Fulflo Pleated Cellulosic series is manufactured with premium grade, phenolic impregnated, cellulosic filter media. Phenolic resin locks the cellulosic fibers into a rigid, porous matrix. This structure provides superior particle removal and particle retention performance under the most severe conditions. Fulflo Pleated Cartridges are available in 2μm, 3μm, 10μm, 30μm and 60μm pore sizes (99%+ removal: ß = 100). Benefits

Premium pleated cellulosic media allow high flow capacity at low pressure drop

Available in a variety of cartridge lengths and end cap configurations to fit most industrial vessels

Phenolic resin impregnated to provide strength, integrity and high contaminant capacity

High flow rates permit the use of smaller vessels and fewer cartridges

Lower P reduces power requirements and pump wear and tear

Longer cartridge life reduces frequency of filter change out resulting in less disposal costs, reduced inventory and less process interruptions

Applications

Chemical Oil Field Photographic Film & Paper Metal Treatment Process Water Synthetic Fibers Process Gas Petroleum Coatings, Paint Ink & Resins Recording Media

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118Fax: (248) 377-3172

[email protected] www.tfsi1.com

162

LIQUID PROCESS FILTRATION - PLEATED CELLULOSIC CARTRIDGEFulflo® PCC Filter Cartridge

Performance Attributes

PCC / PCG flow factor (psid/gpm @ 1 cks)

Flow Rate and Pressure Drop Formulas Flow rate (gpm) = Clean P x Length Factor Viscosity x Flow Factor

Clean P = Flow Rate x Viscosity x Flow Factor Length Factor

Rating (µm)

Flow Factor

2 0.026 3 0.017 10 0.002 30 0.001 60 0.0005

Beta Ratio (ß) = Upstream Particle Count @ Specified

Particle Size and Larger -----------------------------------------------------------------------------------------------------------------------------------------------

Downstream Particle count @ Specified Particle Size and Larger

Percent Removal Efficiency = (1 1) x 100

Performance determined per ASTM F-795-88. Single-Pass Test using AC test dust in water at a flow rate of 3.5 gpm per 10 in (13.2 lpm per 254 mm) cartridge. Notes: 1. Clean P is PSI differential at start. 2. Viscosity is centistokes. use conversion

Tables for other units. 3. Flow Factor is P/GPM at 1 cks for 10 in

(or single). 4. Length Factors convert flow or P from 10 in

(single length) to required cartridge length.

Specifications

Materials of Construction: Phenolic impregnated cellulosic media (PCC) Polypropylene support Stainless steel support (optional) PCG is glass-modified cellulose

Recommended Operating Conditions: Maximum 10 gpm per 10 in length (38 lpm/254 mm) Stainless Steel Support: Maximum Temperature: 250F (121C) Maximum DP: 50 psi (3.5 kg/cm2) Optimum Change Out DP: 35 psi (2.5 km/cm2) Polypropylene support Maximum Temperature @ 10 psid (0.7 km/cm2): 200F (93C) Maximum Temperature @ 35 psid (2.5 km/cm2): 125F (52C) Maximum P @ 75°F (24° C): 60 psi (4.2 kg/cm2) Change Out DP: 35 psi (2.5 km/cm2) Filtration Ratings

99%+ at 2µm, 3µm, 10µm, 30µm, and 60µm pore sizes

Liquid Particle Retention Ratings

Cartridge ß = 5000 Absolute

ß = 1000 99.9%

ß = 100 99%

ß = 50 98%

ß @2 micron

PCG020 10 8.6 1.8 0.9 110 PCC3 12 10 3.2 1.7 64 PCC10 22 18 6 3.2 35 PCC30 100 85 11 4.5 25 PCC60 150 90 30 15.0 10

_______________________________________________________________________________________________ Ordering Information

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118 Fax: (248) 377-3172

[email protected] www.tfsi1.com

163

LIQUID PROCESS FILTRATION - MEMBRANE FILTER CARTRIDGEFluoroflow® Cartridges All-fluoropolymer cartridge for effective filtration of aggressive chemicals Fluoroflow® pleated filter cartridges feature an all-fluoropolymer construction; this provides the highest chemical resistance when filtering acids, bases and solvents. Fluoroflow® cartridges fit standard filter housings and are available in a variety of filter ratings, lengths and end-fittings for maximum versatility. Fluoroflow® cartridges are available flushed with UPW to minimize extractables and wet-packed to eliminate the need for on-site wetting, to fit your needs. The Fluorflow cartridge is available in 0.05, 0.1, 0.2, 0.45, 1 and 100μm pore sizes. Benefits

High chemical compatibility maximizes process capability

Wet-packed option eliminates lengthy wetting procedure and minimizes equipment downtime

Bio-safe in accordance with USP Class VI 121° C Plastics Test

Applications

Aggressive chemicals and process fluids at temperatures up to 150° C

Ozonated and/or hot UPW

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118Fax: (248) 377-3172

[email protected] www.tfsi1.com

164

LIQUID PROCESS FILTRATION - MEMBRANE FILTER CARTRIDGEFluoroflow® Cartridges

Performance Attributes Water in Flow rates, Typical *

0.05µm 0.9gpm/psid (4.9lpm/100mbar) 0.10µm 2.3gpm/psid (12.7lpm/100mbar) 0.20µm 3.2gpm/psid (17.6lpm/100mbar) 0.45µm 4.7gpm/psid (25.8lpm/100mbar) 1.00µm 6.7gpm/psid (36.9lpm/100mbar) * Per 10-inch (250 mm) cartridge equivalent and for fluids with viscosity of 1cP.

Integrity test values

Filter Rating Bubble Point* µm psig bar 0.05 40 2.8 0.10 21 1.5 0.20 13 0.9 0.45 7 0.5 1.00 3 0.2

* In 60/40 IPA/water @ 25° C

Specifications Materials of Construction

100% Fluoropolymer construction Effective Filtration Area

6.8ft2 (0.63m2) per nominal 10” (250mm) cartridge

Metals Extractables

<20ppb (total) in a 10% HNO3 extraction of 1.5 liters for 24 hours at ambient temperature

Maximum differential Pressure Forward:

80psid (5.5bar) @ 75ºF (24C) 55psid (3.8bar) @ 167ºF (75ºC) 30psid (2.0bar) @ 257ºF (125ºC) 15psid (1.0bar) @ 300ºF (150ºC)

Reverse: 50psid (3.4bar) @ 75ºF (24ºC) 15psid (1.0bar) @ 250ºF (121ºC)

Cleanliness (particle shedding)

Wet-packed <2 particles/ml >0.2µm after 7gal at 1gpm

TOC/Resistivity rinse-up (wet-packed)

Toc recovery within 3-5ppb of feed without additional rinse-up. Resistivity recovery within 0.4megohmcm of feed after 22gal @ 1gpm

____________________________________________________________________________

Ordering Information

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118 Fax: (248) 377-3172

[email protected] www.tfsi1.com

165

LIQUID PROCESS FILTRATION - MEMBRANE FILTER CARTRIDGEProflow™ II General Grade Cartridges Hydrophobic PTFE membrane for general purpose gas and solvent purification Proflow™ II General grade cartridges provide an economic alternative for general applications where reliable gas and liquid flow rates are required. With 5.6 square feet of expanded PTFE membrane, Proflow II-G is a highly efficient hydrophobic barrier, for the production of dry gas, and will effectively purify aggressive liquids and organic solvents. Proflow™ II-G cartridges are manufactured under cleanroom conditions and integrity tested before shipment to assure consistent performance and quality. The Proflow™ II-G cartridges are available in 0.05, 0.1, 0.2, 0.45, and 1.0μm pore sizes. Benefits

Reliable air and liquid flow rates for effective performance Broad chemical compatibility enables use in many

applications Broad range of micron ratings for user convenience Superior hydrophobicity for long life in vent/air

applications Integrity tested to ensure quality Bio-safe in accordance with USP class VI 121°C Plastics

Test Applications

Photoresists Compressed gas Venting Electronic grade solvents Hot deionized water (less than 80C)

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118Fax: (248) 377-3172

[email protected] www.tfsi1.com

166

LIQUID PROCESS FILTRATION - MEMBRANE FILTER CARTRIDGEProflow™ II General Grade Cartridges

Performance Attributes Water in Flow rates, Typical * 0.05µm 0.6gpm/psid (3.29lpm/100mbar) 0.10µm 1.2gpm/psid (6.59lpm/100mbar) 0.20µm 2.5gpm/psid (13.73lpm/100mbar) 0.45µm 5.1gpm/psid (28.00lpm/100mbar) 1.00µm 6.2gpm/psid (34.04lpm/100mbar) * Per 10-inch (250 mm) cartridge equivalent and for fluids with viscosity of 1cP.

Integrity test values

Filter Rating Bubble Point*

µm psig bar

0.05 40 2.8

0.10 21 1.5

0.20 13 0.9

* In 60/40 IPA/water @ 25° C

Specifications Materials of Construction Membrane: PTFE Support Layers: Polypropylene Structure: Polypropylene Effective Filtration Area

5.6ft2 (0.52m2) per 10” (250mm) cartridge

Maximum differential Pressure/ Temperature

Forward: 80psid (5.5bar) @ 75ºF (24ºC) 40psid (2.8bar) @ 180ºF (82ºC) Reverse: 50psid (3.4bar) @ 75ºF (24ºC)

Cleanliness (particle shedding)

Wet-packed <1 particles/ml >0.2µm after 6 gal at 1gpm Data is from open bag and installed, no additional installation flushing.

TOC/resistivity rinse-up (wet-packed) TOC rinse-up to background plus 5 ppb of feed after 70 gal @ 1 gpm. Resistivity rinse-up to background minus 0.2 megohm-cm of feed after 30 gal @ 1 gpm.

___________________________________________________________________________________ Ordering Information

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118 Fax: (248) 377-3172

[email protected] www.tfsi1.com

167

LIQUID PROCESS FILTRATION - MEMBRANE FILTER CARTRIDGETefTEC - PTFE Membrane Cartridge

Absolute Rated PTFE Membrane Filter Cartridges TefTEC cartridge filters are constructed with naturally hydrophobic PTFE membrane and polypropylene support layers and components. The HIMA retentive PTFE membrane offers superior hydrophobicity and water intrusion resistance compared to PVDF and polypropylene membranes, and the cartridge construction offers a cost-effective alternative to all-fluorocarbon filters. TefTEC filters are ideal for gas/vent applications and the filtration of aggressive chemicals and solvents.

TefTEC Filter Features–Benefits High surface area, single-layer construction provides superior

flow rates and minimizes filtration system size 100% flushed with 18 M-cm DI water and integrity tested Meets applicable CFR criteria and USP Class VI Biological

Test for plastics Filters are manufactured, flushed, tested and packaged in an

ISO Class 7 cleanroom Environment. Manufactured using Current Good Manufacturing Practices Each filter element is stamped with pore size, lot and serial

number for identification and traceability.

Filter Specifications Media: Gore-Tex® expanded PTFE membrane Inner core, end caps, cage:

Polypropylene

Support layers: Polypropylene O-Rings: Buna-N, EPDM, Silicone, Viton,

Teflon Encapsulated Viton Micron ratings: 0.05 μm, 0.1 μm, 0.2 μm, 0.45 μm,

1.0 μm Dimensions and Operating Parameters Typical Nominal lengths:

9.75’’, 10’’, 20”, 30’’, 40’’ (24.8, 25.4, 50.8, 76.2, 101.6cm)

Outside diameter: 2.7’’ (6.9 cm) Inside diameter: 1.0’’ (2.54 cm) Surface area: 8.5 ft2.(0.79m2)–10 inch element Maximum operating temperature:

203°F (95°C)

Maximum operating pressure:

75 psid @ 70°F (5.2 bar @ 21°C) 40 psid @ 176°F (2.8 bar @ 80°C) 15 psid @ 203°F (1.03 bar @ 95°C)

Maximum reverse differential pressure:

40 psid @ 70°F (2.8 bar @ 21°C)

Performance Specifications: Steam/Autoclave Cartridges will withstand at least 100 steam/autoclave 30 minute cycles @ 275°F (135°C) Integrity Test Values Air Diffusion per 10 inch cartridge wet with 60/40IPA/water. Contact Graver Technologies for specific method. Pore Size Specification 0.05 μm: 50 cc/min @ 22 psig (1.5 bar) 0.1 μm: 50 cc/min @ 18 psig (1.2 bar) 0.2 μm: 20 cc/min @ 12 psig (0.8 bar) 0.45 μm: 15 cc/min @ 5 psig (0.34 bar) 1.0 μm: 15 cc/min @ 3 psig (0.2 bar) Applications Aggressive chemicals Strong acids/bases Solvents Pharmaceutical Intermediates Fermentation air

Tank Vents Compressed

gases Photoresists Hot DI water

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118Fax: (248) 377-3172

[email protected] www.tfsi1.com

168

LIQUID PROCESS FILTRATION - MEMBRANE FILTER CARTRIDGETefTEC - PTFE Membrane Cartridge

Example: TefTEC 0.1-20 P2S

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118 Fax: (248) 377-3172

[email protected] www.tfsi1.com

169

LIQUID PROCESS FILTRATION - POLYETHERSULFONE MEMBRANECARTRIDGE

Clariflow® General Grade Cartridges Hydrophilic Polyethersulfone (PES) membrane for aqueous liquid filtration applications Clariflow® General grade cartridges are designed for general-purpose use in the filtration of high-purity liquids and aqueous chemicals.

The mirrored-anisotropic Polyethersulfone (PES) membrane is inherently hydrophilic and has a pore morphology that delivers exceptionally high flow rates.

Because there are no added surfactants or wetting agents, and the support layers and structure are all-polypropylene, the filter exhibits low extractables, broad chemical compatibility and good resistance to hydrolysis.

The Clariflow general grade cartridge is available in 0.04, 0.1, 0.2, 0.45, 0.65 and 0.8μm pore sizes. Benefits

High flow rate reduces processing time Broad chemical compatibility allows use in most

applications Low differential pressure reduces system wear and tear Bio-safe in accordance with USP class VI 121C

Plastics test Applications

Chemical filtration Liquid clarification Recirculating fluids General use water filtration Deionized water systems

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118Fax: (248) 377-3172

[email protected] www.tfsi1.com

170

LIQUID PROCESS FILTRATION - POLYETHERSULFONE MEMBRANECARTRIDGE

Clariflow® General Grade Cartridges

Specifications Materials of Construction Membrane: Polyethersulfone Support Layers: Polypropylene Structure: Polypropylene Effective Filtration Area

6.8 ft2 (0.63 m2) per 10” (250mm) cartridge

Maximum differential Pressure/ Temperature Forward: 80 psid (5.5 bar) @ 75ºF (24ºC) 40 psid (2.8 bar) @ 180ºF (82ºC) Reverse: 50 psid (3.4 bar) @ 75ºF (24ºC) Performance Attributes Water in Flow rates, Typical * 0.04µm 1.0gpm/psid (5.29lpm/100mbar) 0.10µm 1.8gpm/psid (9.88lpm/100mbar) 0.20µm 3.7gpm/psid (20.31lpm/100mbar) 0.45µm 4.8gpm/psid (26.35lpm/100mbar) 0.65µm 9.2gpm/psid (50.51lpm/100mbar) 0.80µm 9.5gpm/psid (52.16lpm/100mbar) * Per 10-inch (250 mm) cartrdige equivalent and for fluids with viscosity of 1cP.

____________________________________________________________________________ Ordering Information

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118 Fax: (248) 377-3172

[email protected] www.tfsi1.com

171

LIQUID PROCESS FILTRATION - POLYETHERSULFONE MEMBRANECARTRIDGE

Clariflow® WS Cartridges Hydrophilic Polyethersulfone (PES) membrane for cost-effective purification Clariflow WS cartridges are cost-effective alternatives to Clariflow Electronics and General grade cartridges for the filtration of a variety of aqueous liquids.

The Clariflow WS cartridge is built around a unique polyethersulfone (PES) membrane that is inherently hydrophilic, and contains no added surfactants or wetting agents. As such, it is known for clean filtrates, and also offers competitive flow rates, extended service life, and excellent resistance to hydrolysis.

Clariflow WS cartridges are fabricated under cleanroom conditions.

The Clariflow WS cartridge is available in 0.04, 0.1, 0.2, 0.45, and 0.65μm cartridges. Benefits

Reliable and cost-effective to reduce expenses Broad chemical compatibility allows use in aqueous

applications Resistance to hydrolysis allows extended use in UPW

systems High flow rate / low differential pressure reduces system

wear and tear Bio-safe in accordance with USP Class VI 121°C Plastics

Test Applications

Deionized water filtration Chemical filtration Liquid clarification Recirculating liquids Wine and beer clarification Juices Bottled water

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118Fax: (248) 377-3172

[email protected] www.tfsi1.com

172

LIQUID PROCESS FILTRATION - POLYETHERSULFONE MEMBRANECARTRIDGE

Clariflow® WS Cartridges

Performance Attributes Water in Flow rates, Typical * 0.04µm 0.7gpm/psid (3.84lpm/100mbar) 0.10µm 1.3gpm/psid (7.14lpm/100mbar) 0.20µm 2.6gpm/psid (14.27lpm/100mbar) 0.45µm 3.8gpm/psid (20.86lpm/100mbar) * Per 10-inch (250 mm) cartridge equivalent and for fluids with viscosity of 1cP.

Specifications Materials of Construction Membrane: Polyethersulfone Support Layers: Polypropylene Structure: Polypropylene Effective Filtration Area

5.4ft2 (0.50m2) per 10” (250mm) cartridge Maximum Differential Pressure

Forward: 80psid (5.5bar) @ 75ºF (24ºC) 40psid (2.8bar) @ 180ºF (82ºC) Reverse: 50psid (3.4bar) @ 75ºF (24ºC)

Bulk Packaging

Bulk packaged in case quantities to reduce material disposal 10” 28 per carton 20” 12 per carton 30” 12 per carton 40” 9 per carton

____________________________________________________________________________

Ordering Information

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118 Fax: (248) 377-3172

[email protected] www.tfsi1.com

173

LIQUID PROCESS FILTRATION - POLYETHERSULFONE MEMBRANECARTRIDGE

ZTEC B - Polyethersulfone Membrane CartridgePleated Polyethersulfone (PES) Membrane for Bioburden Reduction in Beverages and Biopharmaceuticals ZTEC B Bioburden Reduction grade membrane cartridges provide consistent performance for bioburden reduction and particle removal across a wide range of beverage, pharmaceutical and biological fluids. The naturally hydrophilic PES membrane filters provide exceptional flow rates, long on-stream life, broad chemical compatibility and have no added surfactants to contribute to extractables. The cartridges are integrity testable and steamable to assure reliable service in critical applications. Filter Features–Benefits Manufactured in an ISO Class 7 Cleanroom Environment 100% flushed with 18 M-cm DI water and integrity tested Meets USP Class VI Biological Test for Plastics All materials are FDA listed for food and beverage contact Repeatably Steamable/Sanitizable High retentions up to 107/cm2 challenged for bacteria and yeast Pore size, lot and serial number are stamped on each filter element

for identification and traceability

Typical Applications Bottled Water Opthalmic Solutions Culture Media Reagent Chemicals LVPs Buffers Juices

Filter Specifications Media: Asymmetric Polyethersulfone membrane Inner core, end caps, cage: Polypropylene Support layers: Spunbonded Polypropylene Gaskets/O-Rings: Buna-N, EPDM, Silicone, Viton, Teflon

Encapsulated Viton O-Rings Micron ratings: 0.2 μm, 0.45 μm, 0.65 μm Dimensions and Operating Parameters

Nominal lengths: 9.75’’, 10’’, 20’’, 30’’, 40’’ (24.7, 25.4, 50.8, 76.2, 101.6 cm)

Outside diameter: 2.7’’ (6.9 cm) Inside diameter: 1.0’’ (2.54 cm) Surface area: 7.6 ft2.(0.7m2) per 10 inch element Maximum sustained operating temperature:

180°F (82°C) at 20 psid (1.38 bar)

Maximum differential pressure:

60 psid @ 80°F (4.14 bar @ 27°C) 30 psid @ 160°F (2.07 bar @ 71°C) 15 psid @ 200°F (1.03 bar @ 93.3°C)

Maximum reverse differential pressure: 40 psid @ 70°F (2.8 bar @ 21°C)

Recommended change-out pressure: 35 psid (2.4 bar)

Performance Specifications Hot DI Water Filter cartridge will withstand temperatures of 185°F (85°C) for up to 30 consecutive minutes. Cleaning/Sanitization Compatible with most common chemical cleaning, sanitizing and sterilizing agents and with pH range from1–14. Consult factory for specific compatibility information. Steam/Autoclave Cartridges may be steamed or autoclaved for at least 50 thirty-minute cycles @ 275°F (135°C). Typical Bacterial Retention Performance 0.2μm: LRV for B. diminuta 7.8 0.45μm: LRV for S. marcescens 8.5 0.65μm: LRV for S. cerevisiae 11 LRV for L. brevis 7.6 Integrity Test Specifications Minimum Bubble Point values and maximum Diffusive Air Flow (per 10-inch cartridge) values for ZTEC-B filters wet with water: Pore Size Bubble Point Diffusive Air Flow 0.2 μm: 38psig

(2.6 bar) 35cc/min @ 30psig (2.1 bar)

0.45 μm: 25psig (1.7 bar)

35cc/min @ 20psig (1.4 bar)

0.65 μm: 18psig (1.2 bar)

35cc/min @ 15psig (1.0 bar)

FDA Listed Materials All materials comply with FDA title 21 of the Code of Federal Regulations Sections 174.5, as applicable for food and beverage contact.

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118Fax: (248) 377-3172

[email protected] www.tfsi1.com

174

LIQUID PROCESS FILTRATION - POLYETHERSULFONE MEMBRANECARTRIDGE

ZTEC B - Polyethersulfone Membrane Cartridge

Example: ZTEC B0.2-20P2E = ZTEC B filter, 0.2 micron, 20 inches, 226/Flat, EPDM O-ring

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118 Fax: (248) 377-3172

[email protected] www.tfsi1.com

175

LIQUID PROCESS FILTRATION - POLYETHERSULFONE MEMBRANECARTRIDGE

ZTEC E - Polyethersufone Membrane Cartridge

Pleated Polyethersulfone (PES) Membrane for Final Filtration of Ultrapure Water ZTEC E microelectronics grade cartridges represent Graver’s latest development in ultrapure water filtration technology. The filters are inherently hydrophilic and contain no added surfactants or wetting agents that could contaminate pure and ultrapure water streams. The PES membrane offers superior flow characteristics, high contaminant capacity and consistent removal of sub-micron particles. The cartridges exhibit rapid rinse-up to 18 M-cm resistivity and single digit ppb levels of TOC. Filter Features–Benefits Manufactured, flushed, tested and packaged, in an ISO Class 7

Cleanroom Environment. Filters are 100% flushed with 18 M-cm DI water and integrity

tested. Resistivity rinse-up to 18 M-cm and single digit ppb TOC levels

with minimal throughput. Available in a variety of end cap/adapter configurations to fit all

industry-standard housings. Pore size, lot and serial number are stamped on each filter element

for identification and traceability.

Filter Specifications Media: Asymmetric Polyethersulfone membrane Inner core, end caps, cage: Polypropylene Support layers: Spunbonded Polypropylene Gaskets/O-Rings: Buna-N, EPDM, Silicone, Viton, Teflon

Encapsulated Viton O-Rings Micron ratings: 0.03 μm, 0.1 μm, 0.2 μm, 0.45 μm Dimensions and Operating Parameters

Nominal lengths: 9.75’’, 10’’, 20’’, 30’’, 40’’ (24.7, 25.4, 50.8, 76.2, 101.6 cm)

Outside diameter: 2.7’’ (6.9 cm) Inside diameter: 1.0’’ (2.54 cm) Surface area: 7.6 ft2. (0.7m2) per 10 inch element

Maximum differential pressure:

60 psid @ 80°F (4.14 bar @ 27°C) 30 psid @ 160°F (2.07 bar @ 71°C) 15 psid @ 203°F (1.03 bar @ 95°C)

Maximum reverse differential pressure: 40 psid @ 70°F (2.8 bar @ 21°C)

Recommended change-out pressure:

35 psid (2.4 bar)

Performance Specifications Hot DI Water Filter cartridge will withstand temperatures of 185°F (85°C) for up to 30 consecutive minutes. Cleaning/Sanitization Compatible with most common chemical cleaning, sanitizing and sterilizing agents and with pH range from1-14. Consult factory for specific compatibility information. Rinse-Up Volumes Resistivity rinse-up to 18 M-cm: <30

minutes at a flow of 3 gpm per 10-inch element.

Rinse-up to single-digit ppb TOC in <120 minutes at a flow of 3 gpm per 10-inch element.

Integrity Test Specifications Maximum Diffusive Air Flow (per 10-inch cartridge) values for ZTEC-E filters wet with water: 0.03 μm: 50 cc/min @ 45 psig (3.1 bar) 0.1 μm: 50 cc/min @ 40 psig (2.8 bar) 0.2 μm: 35 cc/min @ 30 psig (2.1 bar) 0.45 μm: 35 cc/min @ 20 psig (1.4 bar)

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118Fax: (248) 377-3172

[email protected] www.tfsi1.com

176

LIQUID PROCESS FILTRATION - POLYETHERSULFONE MEMBRANECARTRIDGE

ZTEC E - Polyethersufone Membrane Cartridge

Example: ZTEC E 0.45-30P8T = ZTEC E filter, 0.45 micron, 30 inches, 222/Fin, Teflon encap. Viton O-rings

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118 Fax: (248) 377-3172

[email protected] www.tfsi1.com

177

LIQUID PROCESS FILTRATION - POLYETHERSULFONE MEMBRANECARTRIDGE

ZTEC G - Polyethersulfone Membrane Cartridge

Absolute Rated Polyethersulfone Membrane Pleated Filter Cartridges This pleated, disposable filter element is constructed of absolute rated, hydrophilic, asymmetric polyethersulfone membrane with extended filter area to allow for a high system flow rate. Filter Features–Benefits 7.0 ft2 (0.65 m2) of membrane surface area per 10" element

–High throughput –Longer on-line service reduces costly maintenance time

Absolute rated membrane from 0.1 to 0.65 μm Manufactured in an ISO Class 7 cleanroom environment 100% flushed with 18 M-cm DI water and gross integrity tested Meets USP Class VI biological test for plastics Fixed pore construction eliminates dirt unloading as differential

pressure increases Low extractables

Filter Specifications Media: Asymmetric Polyethersulfone

membrane Inner core, end caps, cage: Polypropylene Support layers: Spunbonded Polypropylene Gaskets/O-Rings: Buna-N, EPR, Silicone, Viton, Teflon

Encapsulated Viton O-Rings Micron ratings: 0.1, 0.2, 0.45, 0.65 μm Dimensions and Operating Parameters

Nominal lengths: 9.75’’, 10’’, 20’’, 30’’, 40’’ (24.7, 25.4, 50.8, 76.2, 101.6 cm)

Outside diameter: 2.7’’ (6.9 cm) Inside diameter: 1.0’’ (2.54 cm) Surface area: 7 ft2. (0.65m2) per 10 inch element Maximum sustained operating temperature:

180°F (82°C) at 20 psid (1.38 bar)

Maximum differential pressure:

60 psid @ 80°F (4.14 bar @ 27°C) 30 psid @ 160°F (2.07 bar @ 71°C) 15 psid @ 200°F (1.03 bar @ 93.3°C)

Maximum reverse differential pressure:

40 psid @ 70°F (2.8 bar @ 21°C)

Recommended change-out pressure:

35 psid (2.4 bar)

Performance Specifications

Hot DI Water Filter cartridge will withstand temperatures of 185°F (85°C) for up to 30 consecutive minutes. Chemical Compatibility Filter cartridge resists most acids and bases, pH 1–14 and most oxidizing agents. Sanitizing Agents Filter cartridge may be sanitized in place with common oxidizing agents. Steam/Autoclave Cartridges may be steamed or autoclaved for at least 50 thirty-minute cycles @ 275°F (135°C).

Applications Food & Beverage Cosmetics Chemicals Aqueous solutions

Filtration of acids and bases

Ink Ultra pure water

FDA listed materials All polypropylene material used in manufacturing complies with the regulations of the Food and Drug Administration (FDA) title 21 of the Code of Federal Regulations Sections 174.5, as applicable for food and beverage contact.

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118Fax: (248) 377-3172

[email protected] www.tfsi1.com

178

LIQUID PROCESS FILTRATION - POLYETHERSULFONE MEMBRANECARTRIDGE

ZTEC G - Polyethersulfone Membrane Cartridge

Example: ZTEC G 0.1-10P7S = ZTEC G filter, 0.1 micron, 10 inches, 226/Fin, Silicone O-rings

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118 Fax: (248) 377-3172

[email protected] www.tfsi1.com

179

LIQUID PROCESS FILTRATION - POLYETHERSULFONE MEMBRANECARTRIDGE

ZTEC WB - Polyethersulfone Membrane Cartridge

Pleated Polyethersulfone (PES) Membrane for Critical Filtration in Wine and Beer ZTEC WB cartridge filters utilize a special polyethersulfone membrane to provide consistent removal of spoilage organisms and inorganic particulate. The product offers excellent retention efficiency and extended on-stream life making it an ideal filter for the clarification of beer and wine. The PES membrane, available with either 0.65 or 0.45 μm pore sizes, is designed to meet and surpass the filtration criteria necessary to maintain product quality and characteristics. Produced in an ISO Class 7cleanroom, the cartridges are integrity tested during production to assure performance and consistency. Filter Features–Benefits Manufactured in an ISO Class 7 cleanroom environment 100% flushed with 18 M-cm DI water and integrity tested Low adsorption of protein, color and flavor components All materials are FDA listed for food and beverage contact Steamable/sanitizable for cleaning and reuse High log reduction values for spoilage organisms PES membrane provides high capacity contaminant loading Typical Applications White Wine Red Wine Beer Sparkling Wine Wine/Malt Coolers Champagne Distilled Spirits

Filter Specifications Media: Asymmetric Polyethersulfone membrane Inner core, end caps, cage: Polypropylene Support layers: Spunbonded Polypropylene Gaskets/O-Rings: Buna-N, EPDM, Silicone, Viton, Teflon

Encapsulated Viton O-Rings Micron ratings: 0.45 μm, 0.65 μm Dimensions and Operating Parameters

Nominal lengths: 9.75’’, 10’’, 20’’, 30’’, 40’’ (24.7, 25.4, 50.8, 76.2, 101.6 cm)

Outside diameter: 2.7’’ (6.9 cm) Inside diameter: 1.0’’ (2.54 cm) Surface area: 7.6 ft2.(0.7m2)per 10 inch element Maximum sustained operating temperature:

180°F (82°C) at 20 psid (1.38 bar)

Maximum differential pressure:

80 psid @ 70°F (5.5 bar @ 21°C) 40 psid @ 176°F (2.8 bar @ 80°C)

Maximum reverse differential pressure:

40 psid @ 70°F (2.8 bar @ 21°C)

Recommended change-out pressure:

35 psid (2.4 bar)

Performance Specifications Hot DI Water Filter cartridge will withstand temperatures of 185°F (85°C) for up to 30 consecutive minutes. Cleaning/Sanitization Compatible with most common chemical cleaning, sanitizing and sterilizing agents and with pH range from 1–14. Consult factory for specific compatibility information. Steam/Autoclave Cartridges may be steamed or autoclaved for at least 50 thirty-minute cycles @ 275°F (135°C).

Typical Bacterial Retention Performance 0.45μm: LRV for Lactobacillus brevis 7.6 0.45μm: LRV for Oenococcus oeni 10.0 0.45μm: LRV for S. cerevisiae 11 0.65μm: LRV for S. cerevisiae 8.7 Integrity Test Specifications Minimum Bubble Point values and maximum Diffusive Air Flow (per 10-inch cartridge) values for ZTEC WB filters wet with water: Pore Size Bubble Point Diffusive Air Flow 0.45 μm: 20psig

(1.4 bar) 35cc/min @ 16psig (1.1 bar)

0.65 μm: 17psig (1.2 bar)

35cc/min @ 14psig (1.0 bar)

FDA Listed Materials All materials comply with FDA title 21 of the Code of Federal Regulations Sections 174.5, as applicable for food and beverage contact.

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118Fax: (248) 377-3172

[email protected] www.tfsi1.com

180

LIQUID PROCESS FILTRATION - POLYETHERSULFONE MEMBRANECARTRIDGE

ZTEC WB - Polyethersulfone Membrane Cartridge

Example: ZTEC WB 0.45-20P2E = ZTEC WB filter, .45 micron, 20 inches, 226/Flat, EPDM O-ring

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118 Fax: (248) 377-3172

[email protected] www.tfsi1.com

181

LIQUID PROCESS FILTRATION - TRACK-ETCH MEMBRANECARTRIDGE

VTEC - Track-Etch Membrane Cartridge

Absolute Rated Polyester Track-Etch Membrane Filter Cartridges This pleated filter element is constructed of a double layer of Track-Etch polyester membrane for use in critical filtration applications. The filters are pre-flushed and integrity tested to ensure the optimal level of contamination removal. Filter Features–Benefits Integrity testable 12.5 ft2 (1.2m2) of Track-Etch membrane per 10" element.

–High flow rates –High resistivity, low TOC levels

Sieving capture mechanism results in precise, consistent and reliable filtration Pre-flushed, integrity tested and serialized Meets USP 24 Class VI biological test for plastics All polyester construction Sanitizable with steam, hydrogen peroxide, hot water and other chemical sterilants Cyst removal exceeding ANSI/NSF standard 53 for drinking water Validation guide Pore size, lot and serial number are stamped on each filter element for identification and traceability. Filter Specifications Media: Polyester Track-Etch membrane Inner core, end caps and cage:

Polyester

Support Layer: Polyester Gasket/O-Rings: Buna-N, EPDM, Silicone, Viton,

Teflon Encapsulated Viton O-Rings Micron ratings: 0.05, 0.1, 0.2, 0.4, 0.6, 1.0μm Dimensions and Operating Parameters Nominal lengths: 9.75", 10’’, 20’’, 30’’, 40’’

(24.7, 25.4, 50.8, 76.2, 101.6 cm) Outside diameter: 2.7’’ (6.9 cm) Inside diameter: 1.0’’ (2.54 cm) Surface area: 12.5 sq. ft. (1.2m2)–10 inch element Maximum operating temperature:

176°F (80°C)

Maximum differential pressure:

75 psid @ 70°F (5.5 bar @ 21°C) 5 psid @ 176°F (0.3 bar @ 80°C)

0.4μm Track-etch membrane with 0.5μm latex beads Applications Semiconductor ultrapure water and chemicals Pharmaceutical water Cosmetics water Solvent filtration Bottled water

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118Fax: (248) 377-3172

[email protected] www.tfsi1.com

182

LIQUID PROCESS FILTRATION - TRACK-ETCH MEMBRANECARTRIDGE

VTEC - Track-Etch Membrane Cartridge

VTEC Rinse-Up Performance Typical Results per 10˝ Cartridge*

Quick Flush Background Flush

Resistivity 18 M-cm< 334 Gal. (1264 L) 18.15 M-cm

< 1,300 Gal. (4,920 L)

TOC < 3 ppb < 70 Gal. (265 L)

< 2 ppb < 250 Gal.

(946 L) Particles > pore rating

< 5/mL < 35 Gal. (133 L)

< 1/mL < 10 hrs

*Cartridges flushed before tests. Contact Graver Technologies for test conditions.

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118 Fax: (248) 377-3172

[email protected] www.tfsi1.com

183

LIQUID PROCESS FILTRATION - TRACK-ETCH MEMBRANECARTRIDGE

QTEC - Track-Etch Membrane Cartridge

Absolute Rated Polyester Track-Etch Membrane Filter Cartridges This pleated filter element is constructed of Track-Etch polyester membrane for use in general filtration applications. The precise retention characteristics and cleanliness of Track-Etch membrane provides reliable performance over a broad range of conditions.

Filter Features–Benefits Sieving capture mechanism results in precise, consistent and reliable filtration 2.5 sq. ft. (1.2m2) of Track-Etch membrane per 10" element.

–High flow rates –High resistivity, low TOC levels –Precise, predictable contaminant removal

Meets USP 24 Class VI biological test for plastics Sanitizable with steam, hydrogen peroxide, hot water and other chemical sterilants All-polyester construction

–Exceptionally clean –Rapid flush –Not subject to ionic contamination like charged nylon

Filter Specifications Media: Polyester Track-Etch membrane Inner core, end caps and cage:

Polyester

Support Layer: Polyester Gasket/O-Rings: Buna-N, EPR, Silicone, Viton,

Teflon Encapsulated Viton O-Rings Micron ratings: 0.1, 0.2, 0.4, 0.6μm Dimensions and Operating Parameters Nominal lengths: 9.75", 10’’, 20’’, 30’’, 40’’

(24.7, 25.4, 50.8, 76.2, 101.6 cm) Outside diameter: 2.7’’ (6.9 cm) Inside diameter: 1.0’’ (2.54 cm) Surface area: 12.5 sq. ft. (1.2m2)–10 inch element Maximum operating temperature:

176°F (80°C)

Maximum differential pressure:

75 psid @ 70°F (5.5 bar @ 21°C) 5 psid @ 176°F (0.3 bar @ 80°C)

Applications Semiconductor ultrapure water and chemicals Pharmaceutical water General industrial water Solvents Recirculating, plating and etch baths

0.4μm Track-etch membrane with 0.5μm latex beads

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118Fax: (248) 377-3172

[email protected] www.tfsi1.com

184

LIQUID PROCESS FILTRATION - TRACK-ETCH MEMBRANECARTRIDGE

QTEC - Track-Etch Membrane Cartridge

QTEC Rinse-Up Performance Typical Results per 10˝ Cartridge*

Quick Flush Background Flush

Resistivity 18 M-cm< 80 Gal. (303 L) 18.15 M-cm

< 1,300 Gal. (4,920 L)

TOC < 5 ppb < 35 Gal. (133 L)

< 2 ppb < 150 Gal.

(568 L Particles > pore rating

< 5/mL < 35 Gal. (133 L)

< 1/mL < 150 Gal.

(568 L) *Cartridges flushed before tests. Contact Graver Technologies for test conditions.

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118 Fax: (248) 377-3172

[email protected] www.tfsi1.com

185

LIQUID PROCESS FILTRATION - TRACK-ETCH MEMBRANECARTRIDGE

WaterTEC - Membrane Cartridge

Absolute Rated Polyester Track-Etch Membrane Filter Cartridges This pleated filter element is constructed of a double layer of Track-Etch polyester membrane for use in critical filtration applications. The filters are pre-flushed and integrity tested to ensure the optimal level of contamination removal. Filter Features–Benefits Integrity testable 12.5 ft2 (1.2m2) of Track-Etch membrane per 10" element.

–High flow rates –High resistivity, low TOC levels

Sieving capture mechanism results in precise, consistent and reliable filtration Pre-flushed, integrity tested and serialized Meets USP 24 Class VI biological test for plastics All polyester construction Sanitizable with steam, hydrogen peroxide, hot water and other chemical sterilants Cyst removal exceeding ANSI/NSF standard 53 for Drinking water Validation guide Pore size, lot and serial number are stamped on each filter element for identification and traceability.

Filter Specifications Media: Polyester Track-Etch membrane Inner core, end caps and cage:

Polyester

Support Layer: Polyester Gasket/O-Rings: Buna-N, EPDM, Silicone, Viton,

Teflon Encapsulated Viton O-Rings Micron ratings: 0.05, 0.1, 0.2, 0.4, 0.6, 1.0μm Dimensions and Operating Parameters Nominal lengths: 9.75", 10’’, 20’’, 30’’, 40’’

(24.7, 25.4, 50.8, 76.2, 101.6 cm) Outside diameter: 2.7’’ (6.9 cm) Inside diameter: 1.0’’ (2.54 cm) Surface area: 12.5 sq. ft. (1.2m2)–10 inch element Maximum operating temperature:

176°F (80°C)

Maximum differential pressure:

75 psid @ 70°F (5.5 bar @ 21°C) 5 psid @ 176°F (0.3 bar @ 80°C)

0.4μm Track-etch membrane with 0.5μm latex beads Applications Semiconductor ultrapure water and chemicals Pharmaceutical water Cosmetics water Solvent filtration Bottled water

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118Fax: (248) 377-3172

[email protected] www.tfsi1.com

186

LIQUID PROCESS FILTRATION - TRACK-ETCH MEMBRANECARTRIDGE

WaterTEC - Membrane Cartridge

Example: WaterTEC 0.2-10 P2E

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118 Fax: (248) 377-3172

[email protected] www.tfsi1.com

187

LIQUID PROCESS FILTRATION - CAPSULES

CP capsules are designed and manufactured by Critical Process for small flow and encapsulated disposable cartridge requirements. CP capsules are offered in a wide range of pleated and depth media and offered in four grades; general, food / beverage, electronic and pharmaceutical. Each capsule has been designed to hold the maximum amount of filter media that can be completely and effectively utilized in a capsule. CP capsules lower the cost of filtration and reduce the need for high cost metallic housings. They are well suited for liquids and gas applications with the same attention to quality, traceability, validation and testing.

General Specifications Sanitization / Sterilization Filtered Hot Water: .................... .1940F (900C) Autoclave: ....2500F (1210C), 30 min, multiple cycles Chemical Sanitization : ……….......Industry standardconcentrations of hydrogen peroxide, paracetic acid, sodium hypochlorite and other selected chemicals. Sanitization protocols designed to extend the useful life of CP capsules are available from Critical Process Filtration, Inc..

Note: CP capsules are not to be used in steam.

Pre-sterilized: … CP capsules are offered in both a non and pre-sterilized grade. Inlet & Outlet Options Vent & Drain 1/4” Female NPT Standard with Luer- 1/4” Male NPT Lok¨ ports and caps

3/8” Female NPT 1/2” Female NPT 1/2” Male NPT Sanitary Hose Barb

Dimensions

Capsule 2” 5” 10” 20” 30” Inches 5” 8 5/8” 13 3/8” 22 7/8” 32 7/16”

Cm 12.7 22.0 33.9 58.2 82.4

Nominal Length: (length based on capsules with hose barb connections)

Construction Materials ¹ Housing: .............................................…. Polypropylene Filtration Media:

Membranes Depth Pleated Polyethersulfone - PS Polypropylene - PD Nylon - NM Fiberglass - GD Polypropylene - PM PTFE - TM

Depth Polypropylene 85% - MB Polypropylene 95% - BD Polypropylene 99% - NS

Filtration Media Support: ..……....…………PolypropyleneSupport Components: ...................………… PolypropyleneSealing Method: ..........………..............…….Heat - Fused ¹All materials of construction are FDA accepted. Final assemblies have been validated to pass USP class 6 Toxicology extractable tests, oxidizable substances for plastics, endotoxin level and other quality tests.

Maximum Operating Parameters Liquid Operational Pressure: ..….. 80 psi (5.5 bar) at 20°C.Gases Operational Pressure: …...... 60 psi (4.1 bar) at 20°C.Forward Differential Pressure: …...50 psi (3.4 bar) at 20°C.Reverse Differential Pressure: …… 40 psi (2.7 bar) at 20°C.Operating Temperature:……....... 110°F (43°C) at < 30 psi (1.4 bar) in water. Recommended Change Out Pressure: …... 20 psid (2.4 bar)

Pore Size Removal Ratings: ...........................… 0.03 to 100 microns (continue to the media specifications for the specific pore size available)

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118Fax: (248) 377-3172

[email protected] www.tfsi1.com

188

LIQUID PROCESS FILTRATION - CAPSULES

Inlet & Outlet Options

1/4” Female NPT 1/4” Male NPT 3/8” Female NPT

Hose Barb

1/2” Female NPT 1/2” Male NPT Sanitary Ordering Information The capsule catalog number is made up of several variable characters (i.e. pore size, length, filter media, and inlet / outletconfiguration). For example, a general grade polyethersulfone membrane, 0.10 μm , 5 inch length capsule non sterilized with sanitary connections would be designated as: CPGPS*10N000BFF.

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118 Fax: (248) 377-3172

[email protected] www.tfsi1.com

189

LIQUID PROCESS FILTRATION - SORBENT CARTRIDGEFulflo® TruBind™ 300 Cartridges Effective and Economical Hydrocarbon Removal with Enhanced Polymeric Absorbent Cartridges Parker Fulflo® TruBindTM absorbent cartridges utilize a modified polymeric absorbent that economically and effectively reduces trace hydrocarbon contamination in aqueous fluids. The enhanced polymer, configured in a radial-flow-design cartridge, provides maximum utilization of available surface area. This product can be used alone or as an enhancement to other systems. Whether process fluid reclamation or meeting disposal requirements is the goal, TruBind can solve many demanding Hydrocarbon contaminated aqueous fluid problems. Benefits

Increases machine tool life when installed at point-of-use Increases working life of valuable process fluids Reduces hydrocarbon levels to meet EPA discharge

regulations Absorbed hydrocarbon is chemically bound by polymer and

is not leachable Absorbent polymer is enhanced to maximize utilization of

surface area Radial flow design of cartridge allows maximum flow with

minimal pressure drop High integrity construction withstands harsh process

environment A variety of cartridge sizes and end cap options increase

housing selection TruBind cartridges are completely incinerable Parker’s TQM system assures consistent and reliable

performance

Applications

Water Soluble Machine Alkaline Parts Washing Industrial Discharge Water Produced Water Disposal E-Coat Paint Post Oil/Water Separator Compressor Condensate Car & Truck Wash Water Plating Bath Gas & Oil Facility Wastewater Surface Water Runoff (Truck stops, airports, auto

service stations) Bilge Water Pre-Carbon Bed Aerosol Mists Cooling Water Tanker Ballast water Pre-R.O. Membrane Polishing

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118Fax: (248) 377-3172

[email protected] www.tfsi1.com

190

LIQUID PROCESS FILTRATION - SORBENT CARTRIDGEFulflo® TruBind™ 300 Cartridges

Technology Unlike competitive technologies in which hydrocarbons are removed through surface adsorption onto the medium, TruBind cartridges utilize a proprietary modified polymer that both absorbs and chemically binds the hydrocarbon molecules into its interior matrices. The affinity of the polymeric absorbent for hydrocarbon contaminant is so great that accelerated testing by the Toxic Characteristics Leachate Procedure (TCLP) indicated the effluent hydrocarbon level in water to be below current and proposed EPA limits. The modified polymer was formulated to control the speed of hydrocarbon absorption by eliminating the potential for skin formation at the polymer/ hydrocarbon interface. Consequently this polymer, when incorporated into a radial-flow-design cartridge, ensures maximum utilization of surface area. The nature of the polymer makes it an effective absorbent for free, emulsified and dissolved oils, synthetic lubricants, grease and a multitude of organic solvents.

Performance TruBind absorbent cartridge efficiency depends upon the residence time of the fluid within the cartridge, which is a function of the volumetric flow rate. 1. Hydrocarbon Removal Efficiency: At an equivalent

flow rate of 1.0 gpm per 10-inch cartridge The TruBind cartridge typically reduces trace hydrocarbon contaminant in excess of 95% in single pass mode. This efficiency level can be maintained only to a net differential pressure of 10 psi. Series or multi-pass filtration can virtually eliminate hydrocarbon contamination.

2. Hydrocarbon Absorbent Capacity: The TruBind cartridge medium has the potential to remove up to 250 grams (approximately one-half pint) of low density hydrocarbon contaminant. On this basis, the table below provides expected life data in hours or gallons at several trace contaminant levels based on a 1.0 gpm flow rate per 10-inch cartridge. Absorbent capacity will decrease as density of hydrocarbon increases.

3. Flow Rate Capability: A maximum flow rate of 1.0 gpm per 10-inch length cartridge is recommended for the most effective removal of trace hydrocarbon contaminant.

Specifications

Materials of Construction: Absorbent: Proprietary modified polymer Support Construction: 100% polyolefin Seal Material: Gasket (Polyethylene Foam); 222 O-Ring (Buna-N)

Maximum Recommended Operating Conditions:

Temperature: 150F (65C) @ 20 psid (1.4 bar); 180F (82C) @10 psid (0.7 bar) Pressure: 40 psid (2.8 bar) @ 75F (24C) Flow Rate: 1.0 gpm per 10-inch cartridge Changeout Pressure Drop (net): 10 psi (0.7 bar) Flow Factor: 0.03 psid per 1 gpm at 1cks viscosity per 10 in cartridge pH Range: 2 – 12

Lengths: 10-40 in (249mm-1016mm) Outside Diameter: 2-1/2 in (63.5 mm) Inside Diameter: 1-1/16 in (27 mm)

BioSafety:

The TruBind cartridge is classified as non-hazardous and incinerable. Disposal must be dictated by local regulations pertaining to the absorbed contaminant.

Recommended Vessels:

All standard Fulflo vessels designed for 2-1/2 in OD cartridges.

Note: Cost per gallon decreases significantly with longer cartridges.

Hydrocarbon

(ppm)

Concentration

(% by weight)

Hydrocarbon Removal per

Minute (grams)

Estimated Life in Hours

Gallons Fluid

Treated

Estimated Cost per Gallon of Treated

Fluid 10 .001 0.04 106.0 6,330 $ .003

100 .01 0.40 10.6 633 $ .03 1,000 .1 4.00 1.1 63 $ .30

______________________________________________________________________________________________

Ordering Information

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118 Fax: (248) 377-3172

[email protected] www.tfsi1.com

191

LIQUID PROCESS FILTRATION - SORBENT CARTRIDGEFulflo® TruBind™ 400 Cartridges Effective and Economical Hydrocarbon Removal with Enhanced Polymeric Absorbent Cartridges Parker Fulflo TruBindTM absorbent cartridges utilize a modified polymeric absorbent that economically and effectively reduces trace hydrocarbon contamination in aqueous fluids. The enhanced polymer, configured in a radial-flow-design cartridge, provides maximum utilization of available surface area. This product can be used alone or as an enhancement to other systems. Whether process fluid reclamation or meeting disposal requirements is the goal, TruBindTM can solve many demanding hydrocarbon contaminated aqueous fluid problems. Benefits

Increases machine tool life when installed at point-of-use Increases working life of valuable process fluids Reduces hydrocarbon levels to meet EPA discharge

regulations Absorbed hydrocarbon is chemically bound by polymer and

is not leachable Absorbent polymer is enhanced to maximize utilization of

surface area Radial flow design of cartridge allows maximum flow with

minimal pressure drop High integrity construction withstands harsh process

environment TruBindTM cartridges are completely incinerable Parker’s TQM system assures consistent and reliable

performance

Applications

Water Soluble Machine Tool Coolants Alkaline Parts Washing Industrial Discharge Car & Truck Wash Water Gas & Oil Facility Wastewater Tanker Ballast Water Bilge Water Surface Water Runoff Produced Water Disposal (Truck stops, airports,

auto service stations) Pre-Carbon Bed Post Oil/Water Separator E-Coat Paint Compressor Condensate Pre-R.O. Membrane Water Plating Bath Aerosol Mists

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118Fax: (248) 377-3172

[email protected] www.tfsi1.com

192

LIQUID PROCESS FILTRATION - SORBENT CARTRIDGEFulflo® TruBind™ 400 Cartridges

Technology Unlike competitive technologies in which hydrocarbons are removed through surface adsorption onto the medium, TruBind cartridges utilize a proprietary modified polymer that both absorbs and chemically binds the hydrocarbon molecules into its interior matrices. The affinity of the polymeric absorbent for hydrocarbon contaminant is so great that accelerated testing by the Toxic Characteristics Leachate Procedure (TCLP) indicated the effluent hydrocarbon level in water to be below current and proposed EPA limits. The modified polymer was formulated to control the speed of hydrocarbon absorption by eliminating the potential for skin formation at the polymer/ hydrocarbon interface. Consequently this polymer, when incorporated into a radial-flow-design cartridge, ensures maximum utilization of surface area. The nature of the polymer makes it an effective absorbent for free, emulsified and dissolved oils, synthetic lubricants, grease and a multitude of organic solvents.

Performance TruBind absorbent cartridge efficiency depends upon the residence time of the fluid within the cartridge, which is a function of the volumetric flow rate. 1. Hydrocarbon Removal Efficiency: At an

equivalent flow rate of 1.0 gpm per 10-inch cartridge The TruBind cartridge typically reduces trace hydrocarbon contaminant in excess of 95% in single pass mode. This efficiency level can be maintained only to a net differential pressure of 10 psi. Series or multi-pass filtration can virtually eliminate hydrocarbon contamination.

2. Hydrocarbon Absorbent Capacity: The TruBind cartridge medium has the potential to remove up to 250 grams (approximately one-half pint) of low density hydrocarbon contaminant. On this basis, the table below provides expected life data in hours or gallons at several trace contaminant levels based on a 1.0 gpm flow rate per 10-inch cartridge. Absorbent capacity will decrease as density of hydrocarbon increases.

3. Flow Rate Capability: A maximum flow rate of 1.0 gpm per 10-inch length cartridge is recommended for the most effective removal of trace hydrocarbon contaminant.

Specifications

Materials of Construction: Absorbent: Proprietary polymer Support Construction: 100% polyolefin Seal Material: Polyethylene Foam

Cartridge Dimensions (nominal) Lengths:

9-13/16 in (249mm) 19-15/16 in (506mm)

Outside Diameter: 4-1/2 in (114 mm) Inside Diameter: 1-1/16 in (27 mm)

Maximum Recommended Operating Conditions:

Temperature: 150F (65C) @20 psid (1.4 bar); 180F (82C) @10 psid (0.7 bar)

Pressure: 40 psid (2.8 bar) @ 75F (24C)

Flow Rate: 3.0 gpm per 10-inch cartridge Changeout Pressure Drop (net): 10 psi (0.7 bar)

Flow Factor: 0.1 psid per 1 gpm at 1 cks viscosity per 10 in cartridge

pH Range: 2 - 12 BioSafety:

The TruBind cartridge is classified as non-hazardous and incinerable. Disposal must be dictated by local regulations pertaining to the absorbed contaminant.

Recommended Vessels:

Parker LTG10 and LTG20 polymeric vessels and equivalent competitive vessels.

Hydrocarbon

(ppm)

Concentration

(% by weight)

Hydrocarbon Removal per

Minute (grams)

Estimated Life in Hours

Gallons Fluid

Treated

Estimated Cost per Gallon of Treated

Fluid 10 .001 0.11 80.0 14,400 $ .002

100 .01 1.10 8.0 1,400 $ .025 1,000 .1 11.00 0.8 144 $ .24

____________________________________________________________________________________________ Ordering Information

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118 Fax: (248) 377-3172

[email protected] www.tfsi1.com

193

LIQUID PROCESS FILTRATION - SORBENT CARTRIDGEFulflo® TruBind™ 700 Cartridges Effective and Economical Hydrocarbon Removal with Enhanced Polymeric Absorbent Cartridges Parker Hannifin's Fulflo® TruBindTM absorbent cartridges utilize a modified polymeric absorbent that economically and effectively reduces trace hydrocarbon contamination in aqueous fluids. The enhanced polymer, configured a radial-flow- design cartridge, provides maximum utilization of available surface area. This product can be used alone or as an enhancement to other systems. Whether process fluid reclamation or meeting disposal requirements is the goal, TruBindTM can solve many demanding hydrocarbon contaminated aqueous fluid problems. Benefits

Increases machine tool life when installed at point-of-use Increases working life of valuable process fluids Reduces hydrocarbon levels to meet EPA discharge

regulations Absorbed hydrocarbon is chemically bound by polymer and

is not leachable Absorbent polymer is enhanced to maximize utilization of

surface area Radial flow design of cartridge allows maximum flow with

minimal pressure drop High integrity construction withstands harsh process

environment Retrofits parker P, FP, FPM vessel series TruBindTM cartridges are completely incinerable

Applications

Water Soluble Machine Tool Coolants Industrial Discharge Water Produced Water Disposal Pre R.O. Aerosol Mists Injection Molding Cooling Water Car & Truck Wash Water Gas & Oil Facility Wastewater Leisure/Commercial Shipping Floor Scrubbing Waste Water Polishing Bilge Water Alkaline Parts Washing E-Coat Paint Tanker Ballast Water Plating Solutions Pre Carbon Bed Membrane Compressor Condensate Post Oil/Water Separator Surface Water Runoff

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118Fax: (248) 377-3172

[email protected] www.tfsi1.com

194

LIQUID PROCESS FILTRATION - SORBENT CARTRIDGEFulflo® TruBind™ 700 Cartridges Specifications

Materials of Construction: Absorbent: Laminated Proprietary Polymer Support Construction: 100% polyolefin Seal Materia: Buna-N gasket

Cartridge Dimensions (nominal)

Length: 18 in (457 mm) Outside Diameter 6-1/4 in (159 mm) Inside Diameter 2-5/8 in (67 mm) with separate support core

Maximum Recommended Operating Conditions:

Temperature: 150F (65C) @ 20 psid (1.4 bar); 180F(82C) @ 10 psid (0.7 bar) Pressure: 60 psid (4.1 bar) @ 75F (24C) Flow Rate: 5 gpm per cartridge Changeout Pressure Drop (net): 10 psi (0.7 bar) Flow Factor: 0.3 psid per 1 gpm at 1 cks viscosity per cartridge pH range: 2 -12

Recommended Vessels:

Parker Fulflo "P", "FP", "FPM" Series

Biosafety: The TruBindTM cartridge is classified as non hazardous and incinerable. Disposal must be dictated by local regulations pertaining to the absorbed contaminant Technology Unlike competitive technologies in which hydrocarbons are removed through surface adsorption onto the medium, TruBind cartridges utilize a proprietary modified polymer that both absorbs and chemically binds the hydrocarbon molecules into its interior matrices. The affinity of the polymeric absorbent for hydrocarbon contaminant is so great that accelerated testing by the Toxic Characteristics Leachate Procedure (TCLP) indicated the effluent hydrocarbon level in water to be below current and proposed EPA limits. The modified polymer was formulated to control the speed of hydrocarbon absorption by eliminating the potential for skin formation at the polymer/ hydrocarbon interface. Consequently this polymer, when incorporated into a radial-flow-design cartridge, ensures maximum utilization of surface area. The nature of the polymer makes it an effective absorbent for free, emulsified and dissolved oils, synthetic lubricants, grease and a multitude of organic solvents.

Performance TruBind absorbent cartridge efficiency depends upon the residence time of the fluid within the cartridge, which is a function of the volumetric flow rate. 1. Hydrocarbon Removal Efficiency: At an

equivalent flow rate of 5 gpm per cartridge the TruBindTM cartridge typically reduces trace hydrocarbon contaminant in excess of 95% in single pass mode. This efficiency level can be maintained only to a net differential pressure of 10 psi. Series or multi-pass filtration can virtually eliminate hydrocarbon contamination.

2. Hydrocarbon Absorbent Capacity: The

TruBindTM cartridge medium has the potential to remove up to 1200 grams (approximately one quart) of low density hydrocarbon contaminant. On this basis, the table below provides expected life data in hours or gallons at several trace contaminant levels based on a 5 gpm flow rate per cartridge. Absorbent capacity will decrease as density of hydrocarbon increases.

3. Flow Rate Capability: A maximum flow rate of

5 gpm per cartridge is recommended for the most effective removal of trace hydrocarbon contaminant.

Hydrocarbon

(ppm)

Concentration

(% by weight)

Hydrocarbon Removal per Minute (grams)

EstimatedLife in Hours

Gallons Fluid

Treated

Estimated Cost per Gallon of

Treated Flud10 .001 0.189 111.39 31746 $ .003

100 .01 1.795 11.14 3175 $ .030 1,000 .1 17.954 1.11 317.5 $ .295

TruBindTM 700 Series is coreless and requires a support core prior to cartridge installation in vessel. The polyethylene core gives the cartridge sufficient strength and precludes cartridge collapse at recommended operating conditions. Support core is a reusable part and does not need to be replaced. Part Number: 4452-5120

______________________________________________________________________________________________Ordering Information

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118 Fax: (248) 377-3172

[email protected] www.tfsi1.com

195

LIQUID PROCESS FILTRATION - CARTRIDGE HOUSINGSLPF Series Multi-Cartridge Filter Housings

High Quality Multi-Cartridge Filter Housings LPF Series filter housings are constructed of durable stainless steel and meet general purpose industrial and commercial filtration needs. All wetted welded surfaces are stainless steel. External surfaces are bead blasted for a consistent, easy care finish. Applications Potable water Process water Coatings

Edible oils Lubricants Coolants

Cutting oils Solvents

Housing Features Durable 304L or 316L stainless steel for excellent corrosion resistance Universal seat cups accept DOE or 222 style filters; 226 cups optional Choice of V-band clamp or swing bolts for convenient cartridge change outs Eye nuts on swing bolt style facilitate removal with minimal tools Accepts 10”, 20”, 30”and 40” cartridges Fully threaded tie rod allows for fitment of various style/lengths of filters; wing nut for ease of removal Removable cartridge posts for easy cleanouts Suitable for flow rates from 21 to 588 GPM Accommodates up to 2 3/4" OD cartridges Equipped with 1/4” vent and 1/2” drain Available Options 150lb ANSI raised face flange Various MNPT Inlet/Outlet sizes Legs for maximum stability (standard for LPF 7 and up) Mounting tabs (option for LPF 3 and LPF 5) 226 configuration Gauge ports Hinge or davit arm optional on 21 around Housing Specifications Maximum Operating Pressure: 150 psig (10.3 bar) @ 200°F in liquid service. Not for use with compressed gases Shell O-Ring: Buna N, Viton, EPDM, Teflon encapsulated Viton Internal Components: 316L compression plate and tie rod are included for use with single open-end filters. If double open-end filters will be used, specify IP (internal parts) in the housing description to obtain tube guides and springs.

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118Fax: (248) 377-3172

[email protected] www.tfsi1.com

196

LIQUID PROCESS FILTRATION - CARTRIDGE HOUSINGSLPF Series Multi-Cartridge Filter Housings

LPF Series Housing Dimensional Data Dim.

Part Number Rated FlowCapacity3

No. 10”Elements

“A” inches (cm)

“B” inches (cm)

“C” inches (cm) “D”1 inches (cm)

“E”1 inches (cm)

Std. Conn.size/type

Drain Vent

LPF 03-1 21 (79) 3 20 7/8” (53) 7" (17.8) 3" (7.6) 9 1/2" (24.1) 10 5/8" (27) 1 1/2" MNPT 1/2" NPT 1/4" NPTLPF 03-2 42 (159) 6 30 7/8" (78.4) 7" (17.8) 3" (7.6) 9 1/2" (24.1) 10 5/8" (27) 1 1/2" MNPT 1/2" NPT 1/4" NPTLPF 03-3 63 (238) 9 40 7/8" (12.4) 7" (17.8) 3" (7.6) 9 1/2" (24.1) 10 5/8" (27) 1 1/2" MNPT 1/2" NPT 1/4" NPTLPF 03-4 84 (318) 12 50 7/8" (129.2) 7" (17.8) 3" (7.6) 9 1/2" (24.1) 10 5/8" (27) 1 1/2" MNPT 1/2" NPT 1/4" NPTLPF 05-1 35 (132) 5 20 7/8" (53) 7" (17.8) 3" (7.6) 11 1/4" (28.6) 12 3/4" (32.4) 2" MNPT 1/2" NPT 1/4" NPTLPF 05-2 70 (265) 10 30 7/8" (78.4) 7" (17.8) 3" (7.6) 11 1/4" (28.6) 12 3/4" (32.4) 2" MNPT 1/2" NPT 1/4" NPTLPF 05-3 105 (398) 15 40 7/8" (12.4) 7" (17.8) 3" (7.6) 11 1/4" (28.6) 12 3/4" (32.4) 2" MNPT 1/2" NPT 1/4" NPTLPF 05-4 140 (530) 20 50 7/8" (129.2) 7" (17.8) 3" (7.6) 11 1/4" (28.6) 12 3/4" (32.4) 2" MNPT 1/2" NPT 1/4" NPTLPF 07-1 49 (185) 7 28 3/4"² (73.0) 16"² (40.6) 9 3/4"² (24.8) 13 1/2" (34.3) 14 3/4" (37.5) 2" MNPT 1/2" NPT 1/4" NPTLPF 07-2 98 (371) 14 38 3/4"² (98.4) 16"² (40.6) 9 3/4"² (24.8) 13 1/2" (34.3) 14 3/4" (37.5) 2" MNPT 1/2" NPT 1/4" NPTLPF 07-3 147 (557) 21 48 3/4"² (123.8) 16"² (40.6) 9 3/4"² (24.8) 13 1/2" (34.3) 14 3/4" (37.5) 2" MNPT 1/2" NPT 1/4" NPTLPF 07-4 196 (742) 28 58 3/4"² (149.2) 16"² (40.6) 9 3/4"² (24.8) 13 1/2" (34.3) 14 3/4" (37.5) 2" MNPT 1/2" NPT 1/4" NPTLPF 12-2 168 (636) 24 39 3/8"² (97.5) 16"² (40.6) 9 3/4"² (24.8) 17 1/4" (43.8) 17 1/4" (43.8) 3"-150# flange 1/2" NPT 1/4" NPTLPF 12-3 252 (954) 36 49 3/8"² (125.4) 16"² (40.6) 9 3/4"² (24.8) 17 1/4" (43.8) 17 1/4" (43.8) 3"-150# flange 1/2" NPT 1/4" NPTLPF 12-4 336 (1272) 48 59 3/8" ² (150.8) 16"² (40.6) 9 3/4"² (24.8) 17 1/4" (43.8) 17 1/4" (43.8) 3"-150# flange 1/2" NPT 1/4" NPTLPF 21-3 441 (1669) 63 49 3/8"² (125.4) 16"² (40.6) 9 3/4"² (24.8) 21 5/8" (54.9) 21 5/8" (54.9) 4"-150# flange 1/2" NPT 1/4" NPTLPF 21-4 588 (2226) 84 59 3/8"² (150.8) 16"² (40.6) 9 3/4"² (24.8) 21 5/8" (54.9) 21 5/8" (54.9) 4"-150# flange 1/2" NPT 1/4" NPT

Notes: 1. Dimensions are based on the standard connection sizes. 2. Dimensions include support legs. 3. Flow capacity based on pleated filters rated at 7GPM per 10" equivalent. Actual flow rate is dependent upon cartridge type and application.

Example: LPF03R2-N2-U-VB-E-GPX-T-IP

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118 Fax: (248) 377-3172

[email protected] www.tfsi1.com

197

LIQUID PROCESS FILTRATION - FUEL AND HYDROCARBONFILTRATION

CIF Series High Efficiency Pleated Paper Coreless Filter Cartridges To use the CIF Series cartridge requires the one time installation of either a single, double, triple, or quadruple length center tube kit: CIF1KIT CIF2KIT CIF2KIT CIF4KIT Each kit contains all necessary hardware and components required to convert any housing fitted for 6" (152 mm) OD × 3 1/2" (89 mm) ID cartridges. BENEFITS

Crushable- can reduce your disposal volume by approximately 80%

No metal components Flow rates same as “M” Series Incinerable- check your local regulations Cartridge alignment is executed at top of center tube-

easier, quicker Lightweight- contributes to reducing changeout time Same performance and efficiency as M Series high

efficiency pleated paper filter cartridges Nominal micron: 0.5, 1, 2, 5, 10, 25 Gaskets are Buna-N- other materials available upon

request DESCRIPTION

The patented Facet CIF Series high efficiency coreless pleated paper filter cartridges are designed to effectively remove solid contaminants. The filtration of potable liquids is not recommended with this series of filter cartridges. These cartridges are constructed to meet the demanding requirements of the industrial filter market. Media with high efficiency throughout the life of the cartridge is available in ratings of 0.5 to 25 microns. We recommend replacing cartridges when the differential pressure reaches 15 psi. Effective life above 15 psid is minimal.

APPLICATIONS

Gasoline Diesel Coolants Jet Fuel Kerosene AV-gas Rolling Oils Industrial Water Lube Oils Chemicals and Solvents

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118Fax: (248) 377-3172

[email protected] www.tfsi1.com

198

LIQUID PROCESS FILTRATION - FUEL AND HYDROCARBONFILTRATION

CIF Series High Efficiency Pleated Paper Coreless Filter CartridgesFILTER SIZES AND DIMENSIONS

Part Number OD (inches) ID (inches) LENGTH (inches)CIF0.5L 6 3 1/2 14 1/2CIF0.5LX2 6 3 1/2 28 3/4CIF0.5LX3 6 3 1/2 43 1/4CIF0.5LX4 6 3 1/2 57 3/4CIF1L 6 3 1/2 14 1/2CIF1LX2 6 3 1/2 28 3/4CIF1LX3 6 3 1/2 43 1/4CIF1LX4 6 3 1/2 57 3/4CIF2L 6 3 1/2 14 1/2CIF2LX2 6 3 1/2 28 3/4CIF2LX3 6 3 1/2 43 1/4CIF2LX4 6 3 1/2 57 3/4CIF5L 6 3 1/2 14 1/2CIF5LX2 6 3 1/2 28 3/4CIF5LX3 6 3 1/2 43 1/4CIF5LX4 6 3 1/2 57 3/4CIF10L 6 3 1/2 14 1/2CIF10LX2 6 3 1/2 28 3/4CIF10LX3 6 3 1/2 43 1/4CIF10LX4 6 3 1/2 57 3/4CIF25L 6 3 1/2 14 1/2CIF25LX2 6 3 1/2 28 3/4CIF25LX3 6 3 1/2 43 1/4

Note: The dimensions are nominal. These are standard sizes. Many other sizes and combinations are available. Please call us for special sizes.

PERFORMANCE SPECIFICATION NOMINAL REMOVAL MICRON 0.5 1 2 5 10 25 CIF • • • • • •

TEMPERATURE/COMPATIBILITY GUIDE

MEDIA MAXIMUM

TEMPERATURE pH RANGE PETROLEUM PRODUCTS CHEMICALS AQUEOUS SOLUTIONS

Pleated Paper 240 F 5-9 Excellent Good Fair

CARTRIDGE ORDERING INFORMATION SERIES MICRON RATING OUTER BODY TYPE LENGTH SPECIAL FEATURES CIF 5 L X3 0.5, 1, 2, 5, 10, 25 L = Outer Body No Designation = 14 ½” J = Non Asbestos Gasket No designation = No X2 = 28 3/4" N = Neoprene Gasket Outer Body X3 = 43 1/4" V = Viton Gasket X4 = 57 3/4"

MATERIALS OF CONSTRUCTION FILTER MEDIA OPTIONS: 0.5-25 μm: High Efficiency Pleated Paper

GASKET MATERIALS: Standard: Buna-N

COMPONENTS: Center Core: None End Caps: Engineered Plastics Outer Body: Perforated Oil Board

ADHESIVES: Urethane

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118 Fax: (248) 377-3172

[email protected] www.tfsi1.com

199

LIQUID PROCESS FILTRATION - FUEL AND HYDROCARBONFILTRATION

CIF Series High Efficiency Pleated Paper Coreless Filter Cartridges

PARTS FOR ASSEMBLY QUANTITY

ITEM Part

Numbers DESCRIPTION CIF1KIT

for 14 1/2" cartridge

CIF2KIT for 28 1/4" cartridge

CIF3KIT for 44"

cartridge

CIF4KIT for 57"

cartridge 1 606443 Hex nut 1/2" - 13C-2B 1 1 1 1 2 640442 Center tube assembly 1 2 3 4 3 640444 Top adaptor 1 1 1 1 4 640445 Centering guide 0 1 2 3 5 640443 Bottom guide 1 1 1 1 6 606450 Jam nut 1/2" - 13C-2B 1 1 1 1 7 640549 Yoke 1 1 1 1 8 Filter cartridge * * * *

9 Gasket washer * * * * 10 6056402 Flat washer 1 1 1 1 11 606705 Lock washer 1 1 1 1

* Indicates parts not included in kit-shown for reference only.

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118Fax: (248) 377-3172

[email protected] www.tfsi1.com

200

LIQUID PROCESS FILTRATION - FUEL AND HYDROCARBONFILTRATION

FI Series Filter Cartridges BENEFITS

Resin impregnated medias provide strength and durability in demanding applications

Extended surface area for maximum dirt holding capacity and long life

One piece construction reduces downtime, cartridges change-out costs and eliminates filter bypass concerns

Retention ratings available from 0.5 to 100 microns 90-95% nominal efficiency ratings are standard. Higher

efficiency cartridges are available Electro-tin plated components help prevent rust and

corrosion

APPLICATIONS

Automotive Manufacturing Chemicals, Resins, and Solvents EDM Machining Foundries Heating Oils Hydraulic Oils Hydrocarbons Lube Oils Petroleum Refining Pipelines and Petroleum Terminals Power Generation Pulp and Paper Industry

DESCRIPTION

Facet FI Series filter cartridges provide efficient and economical filtration of fluids in a wide range of applications. These industrial filter cartridges are used for removal of particulate from a broad range of products where nominal filtration is required. Facet FI Series filter cartridges provide a large surface area for maximum dirt holding capacity, high flow rates and low initial pressure drops. The normal flow direction is outside to inside, however, specially designed cartridges are available for reverse flow. FI Series cartridges are manufactured using pleated, resin impregnated cellulose or glass cellulose blended medias that are heat cured for strength and durability. Electro-tin plated center cores and outer bodies are the standard metal components. Cartridges are also available without the outer body. Thermosetting PVC adhesives and Buna-N gaskets are standard.

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118 Fax: (248) 377-3172

[email protected] www.tfsi1.com

201

LIQUID PROCESS FILTRATION - FUEL AND HYDROCARBONFILTRATION

FI Series Filter Cartridges

FILTER SIZES AND DIMENSIONS

Part Number OD (inches) ID (inches) LENGTH (inches)FI-209-μ 2 1/2 1 1/16 9 7/8FI-209-μ-3 2 1/2 1 1/16 9 11/16FI-229-μ 2 1/2 1 1/16 29 1/4FI-230-μ 2 1/2 1 1/16 29 5/8FI-412-μ 4 1 5/8 12 1/4FI-511-μ 4 1/2 1 3/4 11FI-518-μ 4 1/2 1 3/4 18FI-518-μ-3 4 1/2 2 5/8 18FI-608-μ 6 3 1/2 8FI-614-μ 6 3 1/2 14 1/2FI-618-μ 6 3 1/2 18FI-636-μ 6 3 1/2 36FI-644-μ 6 3 1/2 44FI-718-μ 6 2 5/8 18FI-718-μ-1 6 2 1/4 18FI-718-μ-3 6 3 3/16 18FI-736-μ 6 2 5/8 36FI-736-μ-1 6 2 1/4 36FI-754-μ 6 2 5/8 54

Note: The dimensions are nominal. These are standard sizes. Many other sizes and combinations are available. Please call us for special sizes. µ = Micron rating Viton is a registered trademark of E. I. duPont de Nemours and Company.

PERFORMANCE SPECIFICATION NOMINAL REMOVAL MICRON 0.5 1 3 5 10 15 20 30 40 50 75 100 Glass/Cellulose • • • Cellulose • • • • • • • • • • •

MATERIALS OF CONSTRUCTION FILTER MEDIA OPTIONS:

0.5-30 μm: Resin Impregnated Cellulose/Glass Blend

5-100 μm: Resin Impregnated Cellulose METAL COMPONENTS: Center Core: Electro-tin Plated End Caps: Electro-tin Plated Outer Cage: Electro-tin Plated GASKET MATERIALS: Standard: Buna-N Optional: Vegetable Fiber, Neoprene, Viton® Non-asbestos Replacement ADHESIVES: Thermoset PVC Urethane Epoxy

TEMPERATURE/COMPATIBILITY GUIDE

MEDIA MAXIMUM

TEMPERATURE pH RANGEPETROLEUM PRODUCTS CHEMICALS

AQUEOUS SOLUTIONS

Glass/Cellulose 250 F 4-9 Excellent Good Good Cellulose 225 F 5-9 Excellent Fair Fair

CARTRIDGE ORDERING INFORMATION SERIES DIMENSIONS MICRON RATING OUTER BODY DESIGNATION SPECIAL FEATURES FI 718 0.5 P H-1 See Filter Sizes 0.5, 1, 3, 5, 10, 15, 20, No Symbol = No Outer Body C3 = High Efficiency Glass/Cellulose and Dimensions 30, 40, 50, 75, 100 P = Outer Body H = Handle Table J = Non Asbestos Gasket N = Neoprene Gasket V = Viton Gasket -1 = Special ID -3 = Hilco Retrofit

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118Fax: (248) 377-3172

[email protected] www.tfsi1.com

202

LIQUID PROCESS FILTRATION - FUEL AND HYDROCARBONFILTRATION

M Series Vertical Filter Housings STANDARD DESIGN FEATURES Body: Welded carbon steel construction — other materials available on

request ASME Code, Section VIII, Div. 1 construction Designed for 150 psi (10.5 kg/cm2 ) @ 250F—higher pressure and

temperature ratings available on request Head closures: Style 1—thru-bolt Styles 2 and 3—swing bolt Head gasket: Buna-N o-ring—other materials available on request Inlet and outlet permanently marked Exterior: Multipurpose prime coated Headlift furnished on 20" (508 mm) and larger

STANDARD CONNECTIONS Inlet and outlet: Style 1—3000# NPT Styles 2 and 3—150# RF (ANSI) flanged Side and bottom drain: 3000# NPT Vent and relief valve: 3/4" 3000# NPT Pressure gauge: 1/4" 3000# NPT

OPTIONS Air Eliminator Differential pressure gauge Pressure relief valve Manual drain valve Interior epoxy coating

M Series vertical filter housings use any of Facet’s M Series high efficiency filter cartridges. A single pass of product through the system removes solids such as rust, dirt, scale, granules and other particles commonly found in liquid process streams.

M Series vertical filter housings are available in three styles in several standard and custom sizes to accommodate specific flow and filtration requirements. They are designed with no internal moving parts to provide easy service and reduced maintenance costs. Each housing is manufactured using quality materials and workmanship to give long-lasting, dependable service.

M Series filter housings can be fitted with either multiple single-length cartridges, stacked 1, 2 or 3 high, or their double-length or triple-length equivalents.

ConnectionsInlet/Outlet

Connections SideDrain

ConnectionsBottom Drain

Anchor Bolt Plan BoltHole Diameter

Anchor Bolt PlanBolt Circle

Anchor BoltPlan

Liquid Volume Weight WithCartridges

Part Number in. mm. in. mm. in. mm. in. mm. in. mm. No. of BoltHoles

gal. ltr. lbs. kgs.

1M-114 2 51 NA NA 3/4 19 7/8 22 11 5/8 295 3 5 19 175 791M-214 2 51 NA NA 3/4 19 7/8 22 11 5/8 295 3 8 30 195 881M-314 2 51 NA NA 3/4 19 7/8 22 11 5/8 295 3 11 42 215 982M-314 4 102 3/4 19 3/4 19 7/8 22 17 432 4 36 136 500 2273M-314 4 102 3/4 19 3/4 19 7/8 22 19 483 4 48 182 550 2494M-314 6 152 3/4 19 3/4 19 7/8 22 21 533 4 62 235 860 3906M-314 6 152 3/4 19 3/4 19 7/8 22 23 584 4 78 295 940 42611M-314 8 203 1 1/2 38 1 25 7/8 22 25 1/4 641 4 175 662 1280 58118M-314 10 254 1 1/2 38 1 25 7/8 22 32 5/8 829 4 350 1325 1975 89627M-314 12 305 1 1/2 38 1 1/2 38 1 25 47 1/2 1206 4 540 2044 2840 1288

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118 Fax: (248) 377-3172

[email protected] www.tfsi1.com

203

LIQUID PROCESS FILTRATION - FUEL AND HYDROCARBONFILTRATION

M Series Vertical Filter Housings

DIMENSIONS

A B C D E F MODEL

NUMBER in. mm. in. mm. in. mm. In. mm. in. mm. in. mm.

HOUSINGSTYLE

HEAD GASKET

1M-114 8 5/8 219 24 1/4 616 3/4 19 23 1/2 596 4 102 12 3/8 314 1 691627 1M-214 8 5/8 219 38 3/4 984 3/4 19 38 965 4 102 12 3/8 314 1 691627

1M-314 8 5/8 219 54 1/2 1378 3/4 19 53 1/2 1359 4 102 12 3/8 314 1 691627

2M-314 14 355 62 1/4 1581 1 25 53 1/2 1359 6 152 24 610 2 607731

3M-314 14 406 62 1/4 1581 1 25 53 1/2 1359 6 152 24 610 2 607731

4M-314 16 406 63 3/4 1619 1 25 55 1397 7 1/2 191 26 660 2 609919

6M-314 20 508 73 1/4 1861 1 1/4 32 62 3/4 1594 7 1/2 191 28 711 2 609920

11M-314 28 711 99 1/4 2521 11 1/4 286 89 1/4 2267 24 610 36 914 3 601299

18M-314 36 914 106 3/4 2711 14 1/4 362 95 1/4 2419 26 660 48 1219 3 601302

27M-314 42 1067 124 1/2 3162 16 3/4 425 98 3/4 2508 29 1/2 749 54 1371 3 602209

NOTES: 1. All dimensions, weights, and volumes are approximate and should be used for estimating only. 2. Cartridges are selected separately to fit specific application requirements. 3. Multiple stack cartridges can be replaced with one single-length equivalent. For example: 1M-214 = 1M-128 or 6M-314 = 6M-143, etc.

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118Fax: (248) 377-3172

[email protected] www.tfsi1.com

204

LIQUID PROCESS FILTRATION - PROCESS LIQUID BAGSStandard Felt Liquid Filter Bags Micron Ratings From 1 to 200 All Industry Standard and Custom Sizes Available Broad chemical compatibility High flow/low pressure drop Sewn or fully-welded construction, Handles on

all bags Choice of steel or molded plastic snap-seal rings Temperature ratings to 200ºF (PO), 275ºF (PE ),

425ºF (HT) and 500ºF (Teflon®) Felt Bag Materials Constructed using 100% synthetic fibers in polypropylene, polyester, Nomex® and Teflon®. The proper combination of fiber diameters, weights and thicknesses result in an economical depth filter media. To reduce fiber migration, Polypropylene bags are treated with a glazed finish, while Polyester and Nomex® bags are singed. Polypropylene and Polyester materials meet FDA regulations for food contact under CFR21, Section 177.1520 Silicone-free construction, High dirt holding capacity Ability to remove both solid and gelatinous particles Low cost Glazed/singed finish on Polypropylene & Polyester reduces fiber-shedding Felt Bag Styles Steel-ring bags have a galvanized steel ring (stainless steel optional) sewn into the top of the bag. They are supplied with sewn seams standard. Plastic flange bags have a specially-designed flange sewn to the top of the bag. They are supplied with sewn seams standard (fully-welded seams available upon request). Welded Construction Fully-welded bags are available in polypropylene and polyester felt for #1, #2, #3, #4 and #5 plastic flanges. No needle holes, increasing efficiencies by preventing by-pass Elimination of threads further reduces possibility of fiber-

shedding

Felt Materials

Micron Ratings

1 3 5 10 25 50 75 100 200 Polyester

Polypropylene Nomex® Teflon®

Ordering Information

Media Type Media Finish Micron Rating

Bag Dimensions Size Diam. Length

Ring / Flange Styles Options

PE = Polyester P = Plain (PE, PO) See Chart P1 = 7.06” 16.5” S = Galvanized steel H = Handle (Standard on all ring style bags)PO = Polypropylene G = Glazed (PO) See Chart P2 = 7.06” 32.0” SS = Stainless steel EB = Edge binding

HT = Nomex® S = Singed (PE, HT) See Chart P3 = 4.12” 8.0” PP = Polypropylene ring A = Auto seams PTFE = Teflon® See Chart P4 = 4.12” 14.0” T = Titanium TTA = Turn, top stitch, auto seam

P5 = 4.12” 24.0” P = AJR-P Flange RC = Reverse collar P7 = 5.50” 15.0” F = AJR-F Flange SB = Spun bond cover P8 = 5.50” 21.0” OSS = AJR-OSS MC = Mesh cover P9 = 5.50” 31.0” DS = Draw string P11= 8.50“ 16.0” NR = No ring P12= 8.50” 30.0” C1 = 7.31” 16.5” C2 = 7.31” 32.5” RP-1= 8.0” 30.0” RP-2= 8.0” 40.0” PC-1= 9.0” 20.0” PC-2= 9.0” 30.0” X1 = 4.35” 8.0” X2 = 4.35” 14.0” XO1= 6.0“ 22.0”

0

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118 Fax: (248) 377-3172

[email protected] www.tfsi1.com

205

LIQUID PROCESS FILTRATION - PROCESS LIQUID BAGSStandard Mesh Liquid Filter BagsMonofilament & Multifilament Micron ratings from 1 to 1500 All industry standard and custom sizes available High flow/low pressure drop media Surface-retention filtration Wide chemical compatibility Sewn construction Handles standard on all bags Choice of steel ring or molded plastic flanges Economical removal of non-deformable contaminants Non-fiber releasing Good removal efficiencies Temperature ratings to 350ºF Polyester and nylon materials meet FDA regulations

for contact under CFR21, section 177.1520 Silicone-free construction

Mesh Bag Materials

Mesh Bag Styles Steel-ring bags have a galvanized steel ring (stainless steel optional) sewn into the top of the bag. They are supplied with sewn seams standard. Plastic flange bags have a specially-designed flange sewn to the top of the bag. They are supplied with sewn seams standard (welded collars available upon request).

Multi-lament Mesh media is woven from threads made of smaller fibers. Bags made from this material are low cost and disposable.

Mono-lament Mesh is woven from single-fiber threads. The openings are square and uniform. Bags made from this material have excellent strength.

Mesh Materials Micro Ratings 1 5 10 25 35 45 50 75 100 125 150 175 200 250 300 400 600 800 1000 1500

NMO = Nylon Monofilament POMO = Polypropylene Monofilament

NMU = Nylon Multifilament PEMU = Polyester Multifilament

Ordering Information

Media Type Micron Rating

Bag Dimensions Size Diam. Length

Ring / Flange Styles Options

NMO = Nylon Monofilament See Chart P1 = 7.06” 16.5” S = Galvanized steel H = Handle (Standard on all ring style bags)POMO = Polypropylene Monofilament See Chart P2 = 7.06” 32.0” SS = Stainless steel EB = Edge binding

NMU = Nylon Multifilament See Chart P3 = 4.12” 8.0” PP = Polypropylene ring A = Auto seams PEMU = Polyester Multifilament See Chart P4 = 4.12” 14.0” T = Titanium TTA = Turn, top stitch, auto seam

P5 = 4.12” 24.0” P = AJR-P Flange RC = Reverse collar P7 = 5.50” 15.0” F = AJR-F Flange P8 = 5.50” 21.0” OSS = AJR-OSS P9 = 5.50” 31.0” DS = Draw string P11 = 8.50“ 16.0” NR = No ring P12 = 8.50” 30.0” C1 = 7.31” 16.5” C2 = 7.31” 32.5” RP-1 = 8.0” 30.0” RP-2 = 8.0” 40.0” PC-1 = 9.0” 20.0” PC-2 = 9.0” 30.0” X1 = 4.35” 8.0” X2 = 4.35” 14.0” XO1 = 6.0 22.0”

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118Fax: (248) 377-3172

[email protected] www.tfsi1.com

206

LIQUID PROCESS FILTRATION - PROCESS LIQUID BAGSHigh Efficiency Liquid Filter BagsHigh Efficiency Microfiber Filter Bags Micron Ratings From 1.0 to 50.0 All Industry Standard and Custom Sizes

Available Choice of Metal Ring Tops or Molded

Super Seal Tops Wide Chemical Compatibility Excellent Oil Absorbing Capabilities Handles on all bags Efficiencies to 95.0%

High Efficiency Bag Materials

Microfiber materials provide high efficiencies at low micron ratings. The optional addition of a needle punched felt layer provides a pre-filter zone and results in extended life.

This multilayer technology option results in a true graded density material with high performance levels.

High Efficiency Bag Styles Standard ring bags have a galvanized steel ring (stainless steel optional) sewn in the top of the bag. They are supplied with sewn seams standard.

Molded Super Seal top filter bags have a plastic top sewn to the filter bag.

High Efficiency Materials (95.0% Min.) Micron Ratings 1A 2A 5A 10A 25A 50A

Polypropylene Polyester

Ordering Information

Media Type Micron Rating Bag Dimensions Size Diam. Length

Ring / Flange Styles Options

POMF - Polypropylene See Chart P1 = 7.06” 16.5” S = Galvanized steel H = Handle (Standard on all ring style bags) PEMF – Polyester See Chart P2 = 7.06” 32.0” SS = Stainless steel

P3 = 4.12” 8.0” PP = Polypropylene ring P4 = 4.12” 14.0” T = Titanium P5 = 4.12” 24.0” P = AJR-P Flange P7 = 5.50” 15.0” F = AJR-F Flange P8 = 5.50” 21.0” OSS = AJR-OSS P9 = 5.50” 31.0” NR = No ring P11 = 8.50“ 16.0” P12 = 8.50” 30.0” C1 = 7.31” 16.5” C2 = 7.31” 32.5” RP-1 = 8.0” 30.0” RP-2 = 8.0” 40.0” PC-1 = 9.0” 20.0” PC-2 = 9.0” 30.0” X1 = 4.35” 8.0” X2 = 4.35” 14.0 XO1 = 6.0 22.0”

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118 Fax: (248) 377-3172

[email protected] www.tfsi1.com

207

LIQUID PROCESS FILTRATION - PROCESS LIQUID BAGSProcess Liquid Bag Flanges

FLANGES

7” D Plastic P1P & P2P

7” D Plastic P1F & P2F

P1OSS & P2OSS

4” D Plastic

P3P, P4P, P5P

4” D Plastic

P3RP, P4RP, P5RP

P3OSS & P4OSS

8” D Plastic XO1 Flange

RP1P & RP2P

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118Fax: (248) 377-3172

[email protected] www.tfsi1.com

208

LIQUID PROCESS FILTRATION - PROCESS LIQUID BAGSProcess Liquid Bag Rings

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118 Fax: (248) 377-3172

[email protected] www.tfsi1.com

209

LIQUID PROCESS FILTRATION - PROCESS LIQUID BAGSSentinel Process Liquid Bags

Welded Construction Filter Bags SENTINEL filter bags represent the industry standard in bypass-free filter construction. Available in polyester and polypropylene materials, all SENTINEL filter bags feature:

SENTINEL Pressure Actuated Seal Ring Silicone Free Needled Felt Super Strong Welded Construction Non Migrating Media Construction Proprietary Construction Proprietary construction processes produce a reliable, durable filter bag. All seams are fully welded, producing strong, reliable joints with no by-pass or loose sewing thread. Seams are both strong and flexible, allowing the filter bag to form to the restrainer basket. The seam edges are heat sealed, eliminating possible loose fibers. This results in a filter bag with durable performance for the most demanding applications.

SENTINEL® Seal Ring All SENTINEL filter bags utilize the SENTINEL seal. Its all-plastic construction provides a flexible, chemically resistant seal which adapts to any filter housing. This unique design employs a pressure activated sealing lip which responds to increases in differential pressure. As the pressure increases, the seal of the ring improves, insuring by-pass free performance over all ranges of pressure, temperature and micron rating. The elevated bag handles make removal of the bag from the vessel quick and easy. When a SENTINEL filter bag is installed into an Eaton filter vessel, the ring snaps into place, holding its position until the vessel is closed. Now, applications requiring polypropylene or polyester felt filter bags can take advantage of the all-welded construction afforded by Eaton SENTINEL® Filter Bags. These bags, made from silicone-free materials, feature super-strong welded construction rather than sewn seams. This construction ensures that nothing bypasses the process media through holes in sewn fabric.

PRODUCT CODES

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118Fax: (248) 377-3172

[email protected] www.tfsi1.com

210

LIQUID PROCESS FILTRATION - PROCESS LIQUID BAGSDuraGaf Process Liquid Bags

Extended Life Filter Bags Can Improve Your Filtration Process and Save You Money

DURAGAF™ Filter Bags for High Performance DURAGAF filter bags represent the state-of-the-art in needled felt bag filter media. Their unique structure delivers equal filtration performance with lifetimes 2-5 times longer than ordinary felt media. The result is reduced operating costs due to lower bag consumption, downtime, change-out labor, storage and disposal. Why DURAGAF™ Filter Bags Last Longer DURAGAF filter bags are available in two extended life materials: polypropylene (code POXL) or polyester (code PEXL). These two materials utilize a fiber blend with a finer fiber diameter and a higher weight than ordinary media. The result is a dramatically higher dirt holding capacity at the same efficiency and differential pressure. Processes run longer and need fewer bag changes with DURAGAF filter bags. All-Welded Construction for Superior Performance All DURAGAF filter bags feature 100% welded fabrication and the Eaton SENTINEL® seal. This construction eliminates the bypass which can occur in standard sewn filter bags. Eaton proprietary welding technology produces a super-strong seam that will stand up to even the most demanding applications without failure. DURAGAF™ Filter Bags Seal Better in Critical Applications The SENTINEL® seal is standard on all DURAGAF filter bags. The unique, pressure-actuated ring actually improves its seal as differential pressure increases. No Downstream Fiber Contamination All DURAGAF filter bags are manufactured with a proprietary downstream surface treatment to prevent fiber migration. A special finish is obtained by glazing the surface, melting fibers together to form a tight, secure downstream matrix. In addition, the weld seams are heat bonded to eliminate loose fibers which might result during fabrication. Food and Beverage Applications DURAGAF filter bags are available in models (POXLF, PEXLF) which are compliant with FDA and EC requirements for food contact.

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118 Fax: (248) 377-3172

[email protected] www.tfsi1.com

211

LIQUID PROCESS FILTRATION - PROCESS LIQUID BAGSDuraGaf Process Liquid Bags

How much longer will a DURAGAF™ Filter Bag last in your application?

Extended Life Felt

Finer fibers More pores thicker media

Surface of Extended Life Felt

No fiber release Full flow through surface channels

PRODUCT CODES

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118Fax: (248) 377-3172

[email protected] www.tfsi1.com

212

LIQUID PROCESS FILTRATION - PROCESS LIQUID BAGSAccuGaf Process Liquid Bags

ACCUGAF™, Filter Bags for Applications Demanding Efficiency >99%

The ACCUGAF filter bag pushes the boundaries of bag filtration technology far beyond traditional designs. With efficiencies >99%, each ACCUGAF model provides cost-effective filtration solutions for demanding applications. The five models assure users that particles from the range of 1.25 microns can be removed effectively while delivering long service life.

High-Efficiency Performance ACCUGAF filter bags feature:

100% welded seams SENTINEL seal ring Meltblown filtration media in polypropylene or polyester No additives, such as resins, binders or surface treatments

FDA Compliant Materials ACCUGAF Polypropylene filter bags are constructed entirely of materials compliant to FDA requirements for materials in contact with food. All materials conform to US Code of Federal Regulations 21 CFR Part 177 and EU Directive 2002/72/EC.

Applications Although ideally suited for food and beverages, ACCUGAF filter bags will deliver equal performance in a wide range of demanding applications such as:

Beer, wine, spirits and beverage filtration Fine particle removal in parts cleaning Final filtration of lacquers Final filtration of vinegar Activated carbon removal in process systems Final filtration of hydraulic oils and lubricants

ACCUGAF Filter Bag Filtration Ratings

Particle Size at Common Removal Efficiencies (μm)Part Number Material >60% >90% >95% >99% >99.9% ¤RTF¤DP (psi) Size 02 @ 45

gpmMax Op. Temp(°F)

AGF 51 Polypropylene 0.2 0.6 0.8 1.5 5 1.30 190AGF 53 Polypropylene 0.8 1 2 3 5 3.20 190AGF 55 Polypropylene 1 2 3 5 15 0.73 190AGF 57 Polypropylene 2 4 5 10 25 0.60 190AGF 59 Polypropylene 10 25 30 25 35 0.44 190AGFE 51 Polyester 0.2 0.6 0.8 1.5 5 1.30 320AGFE 55 Polyester 1 2 3 5 15 0.73 300AGFE 57 Polyester 2 4 5 10 25 0.60 300

Filtration efficiency confirmed by independent testing laboratory

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118 Fax: (248) 377-3172

[email protected] www.tfsi1.com

213

LIQUID PROCESS FILTRATION - PROCESS LIQUID BAGSAccuGaf Process Liquid Bags

OPERATIONAL CONSIDERATIONS Bag Positioner ACCUGAF filter bags must be used with the Eaton bag positioner. This eases insertion and assures correct alignment of the filter bag inside the restrainer basket. In addition, the filter bag will be protected against damage to inadvertent back-flow. Pre-Wetting in Aqueous Solutions ACCUGAF polypropylene filter bags are fabricated from microfiber filtration media. These materials are hydrophobic, indicating that water will not wet the fiber surfaces. As with all other fine polypropylene filters, a lower surface tension fluid (wetting agent) must be used to wet the media prior to introducing water. Prior to service, the filter bags must be immersed in a wetting solution compatible with the process fluid. After wetting, an aqueous fluid will be drawn into the media through capillary action. Full details about installation and wetting are provided with every box of ACCUGAF filter bags. AGFE Polyester For use in higher temperature applications and there is no need for pre-wetting in aqueous solutions.

ACCUGAF Filter Bags are available in retention codes of 51, 53, 55, 57, and 59.To select the perfect ACCUGAF Filter Bag for your application use the chart and choose the retention efficiency level you need on the left side of the chart at particle size in microns at the bottom. Next find which bag efficiency code (identified by the colored lines) is closest to that point. There you have it, the most cost effective filter bag for your critical filtration application.

PRODUCT CODES

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118Fax: (248) 377-3172

[email protected] www.tfsi1.com

214

LIQUID PROCESS FILTRATION - PROCESS LIQUID BAGSClearGaf Process Liquid BagsCLEARGAF™ Filter Bags Fully Compliant and Approved for Food and Beverage Service CLEARGAF™ Filter Bag Features Deliver Advanced Benefits Compliant materials assure compatibility with all food

applications. Sewn bags use special lubricant-free thread Independent verification guarantees conformity to EC

and FDA requirements Low-migration media minimizes substances introduced

to fluids SENTINEL® Ring Bag Seals eliminate fluid bypass All-welded construction eliminates fluid bypass through

needle holes on felt and multi-layer filter bags Controlled production eliminates contamination from

handling and environmental conditions Single packaging keeps bags free from contamination

during shipping, storage and installation Special handling & storage ensures that there is no

contamination after packaging

CLEARGAF filter bags are the first and only series of filter bags specifically designed for the requirements of the food, beverage and pharmaceutical industries. Comprised of several filter styles, CLEARGAF is the only filter bag to deliver: Fully FDA compliant materials per 21 CFR 177 Fully EC compliant per 90/128/EEC Independent testing and certification Special single packaging and warehouse control CLEARGAF™ Filter Bags for Direct Contact with Foodstuffs Filter Bags are widely used for the filtration of fluids that are directly or indirectly used as foodstuffs. In most applications, these types of filters must be carefully selected to ensure that foodstuffs are not contaminated from their use. Most materials used to manufacture disposable filters, including bag filters and cartridge filters, are polymers, which are generally selected for their purity in the application. Many of these materials, however, contain materials that can diffuse out of the plastic into the process fluid. This effect, known as migration, can lead to foodstuff contamination. For this reason, the use of polymers is often limited to products such as CLEARGAF Filter Bags, which are made from materials that have been documented as safe in food applications. CLEARGAF Filter Bags conform to both US FDA and European EC regulations. The difference between the FDA and EC regulations is one of

degree. FDA regulation limits on migration are proportional to weight. EC limits, however, are based on area, and must be demonstrated in tests on finished articles. For heavy material, the EC limits can be up to 50 times more restrictive than the FDA ones. Independent Verification You can be sure all CLEARGAF Filter Bags meet these requirements, because they have been evaluated, tested and certified for EC migration performance by an independent food research institute. CLEARGAF Filter Bags are also made only from materials listed in the US Code of Federal Regulations Title 21 Part 177. No other materials are added during fabrication. Special Manufacturing and Packaging CLEARGAF Filter Bags are manufactured under special conditions to ensure that they contain no contamination. Immediately after manufacture, each bag is individually sealed in protective plastic packaging to keep them contamination-free. Eaton has special warehousing facilities for CLEARGAF Filter Bags to further protect them during storage. No other manufacturer goes to these lengths to ensure the quality of their food grade filter bags. For less demanding food and beverage applications, Eaton offers a line of cost effective filter bags that are appropriate for many applications.

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118 Fax: (248) 377-3172

[email protected] www.tfsi1.com

215

LIQUID PROCESS FILTRATION - PROCESS LIQUID BAGSClearGaf Process Liquid Bags

Selection Chart

Sizes Available Grades

Max.Temp (°F) 01 02 03 04 1 5 10 25 50 80 100 150 200 400 600 800

Ring Style

PEF 285 Z PEXLF 285 Z POF* 195 E

POXLF* 195 E NMOF 285 Z AGF* 195 51 - 53 - 55 - 57 - 59 E PGF* 195 50 - 51 - 55 - 57 E

*Products subject to MPQ in Europe applications. See Technical Bulletin TB990801 for full details.

PRODUCT CODES PEF: polyester needlefelt PEXLF: extended life polyester needlefelt POF: polypropylene needlefelt POXLF: extended life polypropylene needlefelt NMOF: nylon monofilament AGF: polypropylene meltblown PGF: polypropylene meltblown

Bandseal Process Liquid Bags

For simple, minimal pressure non-critical open filtration applications (that is, filtration without a vessel), a BANDSEAL Filter Bag offers many cost-effective choices. These filter bags are available with a drawstring that permits them to be installed directly on the end of a pipe, without the need of an adapter.

PRODUCT CODES

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118Fax: (248) 377-3172

[email protected] www.tfsi1.com

216

LIQUID PROCESS FILTRATION - PROCESS LIQUID BAGSProGaf Process Liquid Bags

The Filter Bag that Works Better Than a Filter Cartridge PROGAF filter bags bring a new, high-performance alternative to applications requiring absolute filtration. PROGAF filter bags’ progressive density depth filtration delivers high efficiency (up to 99.98%) and long life with all the convenient features of a bag filter. In comparison with other filtration technologies, PROGAF filter bags deliver lower operating costs while retaining the ease of change-out typical of a bag filter. Welded Construction for Superior Performance All PROGAF High Performance Filter Bags feature 100% welded construction for better filtration performance. This construction ensures that nothing bypasses the process media through holes in the fabric created from sewing the material. Eaton’s proprietary welding technology produces a super-strong seam that stands up to the most demanding applications.

The SENTINEL plastic step-ring seal provides a seal between the filter vessel and the PROGAF Filter Bag. As the pressure differential rises inside the vessel, the seal becomes more efficient.

PROGAF™ Filter Bags Seal Better in Critical Applications The SENTINEL® ring provides a flexible, chemically-resistant seal which adapts to any filter vessel. This unique design employs a pressure-activated sealing lip which responds to increases in differential pressure. As the pressure increases, the seal of the ring improves, guaranteeing bypass-free performance over all ranges of pressure, temperature and micron rating. The elevated bag handles make removal quick and easy. Unique Progressive Density Media Structure PROGAF filter bags utilize an advanced media structure developed specifically to deliver both long life and absolute filtration. PROGAF filter bags’ progressive density design uses up to 12 layers of media which become finer and finer as fluid passes through. The result is a gradual removal of contaminant without any single layer blinding prematurely. Application and laboratory tests confirm that PROGAF bag filters deliver longer service life and lower operating costs than any other renewable filter element. The 100% polypropylene construction provides pure, silicone-free materials in an economic, self-contained, easily disposable filter bag.

PROGAF™ Filtration Ratings

Particle Size at Common Removal Efficiencies (μm)Part Number >60% >90% >95% >99% >99.9% ¤RTF¤DP (psi) Size 02@ 45 gpmPGF 50 - - .15 .45 1 3.6PGF 51 >[email protected] .3 .45 .5 2 2.5PGF 55 1 3 6 10 12 0.9

Filtration efficiency confirmed by independent test laboratory

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118 Fax: (248) 377-3172

[email protected] www.tfsi1.com

217

LIQUID PROCESS FILTRATION - PROCESS LIQUID BAGSProGaf Process Liquid Bags

Filtration Efficiencies of Up to 99.9% PROGAF High Performance Filter Bags have performance efficiencies of up to 99.9%…true absolute filtration. In many filtration applications of one micron and above, PROGAF Filter Bags can replace expensive cartridge filtration systems and provide better performance while saving time and money. Ask your Eaton Filtration Specialist for “real world” documented case histories, illustrating how PROGAF Filter Bags have performed in applications similar to yours. The PROGAF™ Filter Bag Difference Ordinary standard filter bags are made from needled felt media that has a fiber structure not as fine and precise as the filtration grade melt blown media used for PROGAF Filter Bags. The needled fibers are much larger in size and spaced much further apart, yielding a lower efficiency. PROGAF Filter Bags have been designed to deliver calibrated fractional efficiency on very small particles, down to less than one micron. The bags feature a completely welded construction and the unique, SENTINEL® Sealing Ring for a positive by-pass free seal. And all PROGAF Filter Bags have a round bottom shape for increased pressure stability.

Unique layered construction structure

Choose Just the Filtration Efficiency Your Application Needs PROGAF Filter Bags are available in efficiency codes of 50, 51, and 55. To select the perfect PROGAF Filter Bag for your application, choose the micron retention efficiency level you need on the left side of the chart at particle size in microns at the bottom. Next, locate the bag efficiency code (identified by the colored lines) that is closest to that point. There you have it: the most cost effective filter bag for your critical filtration application.

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118Fax: (248) 377-3172

[email protected] www.tfsi1.com

218

LIQUID PROCESS FILTRATION - PROCESS LIQUID BAGSHayflow Process Liquid Bags

Revolutionary New Filter Element

HAYFlOW™ Filter Element – The Next Generation of Filtration Systems This new, patent pending filter element has combined the best of both bag and cartridge filters into one single filtration element for outstanding filtration performance. Because the surface area of the HAYFLOW element is up to 70% greater than a similar size filter bag, existing systems that use it experience longer filter element life and less changing, resulting in reduced running costs. Designers of new bag filtration systems can opt for reduced running costs or, because of the high flow rates possible with HAYFLOW filter element, reduce filter housing size by up to 50% thus lowering the initial cost of the system. What Makes the HAYFlOW™ Element Better The heart of a HAYFLOW filter element is two concentric cylinders of high-quality extended life Eaton filter media. These cylinders are formed using unique welding technology to create a no by-pass seam. The diameter of the cylinder is the same size as a standard filter bag, so retrofitting into existing systems is easy. The HAYFLOW element is fitted with the SENTINEL® sealing ring, ensuring a positive seal with the filter vessel to protect against bypass of the process media.

How the HAYFlOW™ Element Works The process fluid enters the inside of the element, passes through it, and exits through the vessel outlet. Like a filter bag, the filtered-out material stays inside the HAYFLOW element. The HAYFLOW element is unlike a filter cartridge, where the residue of the filtered material remains on the outside of the cartridge, complicating the changing process. An All-Around Better Choice Changing a HAYFLOW filter element can actually be easier than changing a filter bag. Because of its revolutionary design, it only retains 25% of the residual liquid volume of a similarly sized filter bag. When you need to change the element, it weighs up to 75% less than a filter bag. A full bag can weigh up to 33 lbs, so weight is an important consideration for the system operator.

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118 Fax: (248) 377-3172

[email protected] www.tfsi1.com

219

LIQUID PROCESS FILTRATION - PROCESS LIQUID BAGSHayflow Process Liquid Bags The HAYFLOW Effect

Turbo effect in solids collection helps

to extend life of filter element

Features: Higher flow rates - smaller, less costly housings can be used Up to five times greater life over filter bags Liquid losses are 25% of similar size filter bag SENTINEL sealing ring and 100% welded construction for no by-pass Up to 35 times more effective than standard filter cartridges Low pressure differential results in less energy consumption of pumps Very cost-effective in comparison to similar systems Rugged cylindrical construction Easier maintenance with reduced costs Easy retro fit to existing filter housings And….Eaton’s superior support, before, during and after system installation. Take Advantage of HAYFlOW™ Elements Now You can easily change over from ordinary bag filtration to the revolutionary new HAYFLOW filter element. Existing bag filter housings need only to be fitted with a new HAYFLOW restrainer basket for instant compatibility with the HAYFLOW element. No tools, special equipment or modification to the vessel are required. Just drop in the new basket and you are ready to take advantage of all the benefits offered by a HAYFLOW filtration system. Still Not Sure if HAYFlOW™ Filter Element is Right for You? Contact us. We can show you how you can save money and improve your filtration process using HAYFLOW filter elements.

Application: Automotive Sugar Processing Paints, Coatings, Inks, Dispersions Resins Water and Waste Water Treatment Solvents Lubricants and Metalworking Fluids Aqueous and Solvent Based Cleaners in

Parts Washing Equipment

Pulp and Paper Oil and Gas Exploration and

Processing Pharmaceutical Food Processing Chemical Process Industries Potable Water, Beer, and Wine Edible Oils

Remember “Filter Cost” and “Filtration Cost” are Not the Same Thing We can explain the difference and demonstrate the HAYFLOW filter element advantage in your application.

PRODUCT CODES HAYFlOW™

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118Fax: (248) 377-3172

[email protected] www.tfsi1.com

220

LIQUID PROCESS FILTRATION - PROCESS LIQUID BAGSProcess Liquid Bag Nomenclature Bag Nomenclature Chart

How to read a bag description code

All the information necessary to understand an Eaton filter bag description is listed below. The filter description listed, a PO-10-P04S-H-20S is for a polypropylene, 10 micron, plain cover, 4” x 15” filter bag with a carbon steel ring, a twill handle, packed 20 to a small box.

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118 Fax: (248) 377-3172

[email protected] www.tfsi1.com

221

LIQUID PROCESS FILTRATION - LIQUID BAG FILTER HOUSINGSFlowline II Liquid Bag Filter Housings

Eaton’s advanced engineering provides: Unique one-piece body design that eliminates the

traditional body to bottom cap circumferential weld. Most cost effective solution to single bag vessel

requirements. Rated at 150psi at 250°F for high performance at

economical pricing. Unique internal body to basket seal to prevent bypass. FLOWLINE style cover design provides safe and reliable

“no tools required” access for bag replacement. Displacement style cover prevents spills when opening

the cover. Potential Cost Savings A2” flanged FLOWLINE II SBV in 316SS is up to 28% less expensive than competitors’ offerings.

Unique internal body to basket O-ring seal prevents bypass and is easy to maintain.

FLOWLINE II models come standard with sturdy adjustable legs.

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118Fax: (248) 377-3172

[email protected] www.tfsi1.com

222

LIQUID PROCESS FILTRATION - LIQUID BAG FILTER HOUSINGSFlowline II Liquid Bag Filter Housings

Specifications The FLOWLINE II is available as either #1 size or #2 size units. Choice of three different materials of construction,

Carbon Steel, 304 Stainless Steel and 316 Stainless Steel. Available end connections: 2” NPT or 2” 150# RF flanged.

The #2 size unit is also available with 3” 150# RF flanges in the side in/side out and loop configurations as well as bottom out configuration.

Units come standard with a 316 stainless steel support basket. Kynar® compression ring provides an advanced, long-term solution

for securing the filter media and support basket into the enclosure. Adjustable painted carbon steel mounting legs are included. Buna-N O-rings for the cover and basket seal. Viton or EPDM O-

rings are optional. 1/4” NPT vent and gauge port connections on the cover.

Additional 1/4” NPT gauge connections on the body are optional. The FLOWLINE II with 2” connections is available in three

configurations: side in and bottom out, side in and side out on opposite sides for inline piping or side in and side out on the same side for loop design layouts or duplexing. These units come standard with 2” NPT bottom drain connections.

Bead blast external finish is standard for stainless steel construction and shop paint is standard for carbon steel construction.

SPLASH GUARD option for added safety

Helps protect operators from unexpected pressurized spray and discharge

Reduces operator exposure to potentially hazardous material

Provides additional eye and face protection

FLOWLINE II can be configured into MODULINE™ assemblies Higher efficiency &

operation cost savings Modular flexibility for

adding capacity Smaller footprint than

duplexed multibag housings

Continuous flow capability

Capital cost savings of 30% to 40% or more

Max. Allowable HousingPart Number No. Of

BagsBag Size Max. Flow 2

GPMMaterial 1 Pressure

(PSI)Temperature**

(ºF)Volume

(GAL)Weight

(LBS)Inlet OutletConnection

Type Vent 4 IN

FBF-0101-AB10-020A * 1 1 90 SS or CS 150 250 4 30 2" Flanged 1/4"FBF-0101-AB10-020N * 1 1 90 SS or CS 150 250 4 30 2" NPT 1/4"FBF-0102-AB10-020A * 1 2 180 SS or CS 150 250 7 43 2" Flanged 1/4"FBF-0102-AB10-020N * 1 2 180 SS or CS 150 250 7 43 2" NPT 1/4"

Dimensions In Inches Part Number A B C D E F

FBF-0101-AB10-020A * 17.70 20.75 3.34 7.68 6.70 54.90 FBF-0101-AB10-020N * 17.70 19.64 3.34 7.68 5.37 54.90 FBF-0102-AB10-020A * 17.70 36.31 3.34 7.68 6.70 85.70 FBF-0102-AB10-020N * 17.70 35.19 3.34 7.68 5.37 85.70

1) SS = Austenitic Stainless Steel SS 316 and CF8M or better 2) Maximum theoretical flow based on water viscosity, bag specific 3) Dimensions for reference only and approximate. Exact dimensions for installation purposes available on request. 4) For details, see available product specific data sheet * Part number is for stainless steel construction. Change AB to CS for carbon steel. ** Depending on seal material

Filter Bags

PROGAF™ Absolute rated with up to 15 layers of media

ACCUGAF™ Absolute rated at 99%

LOFCLEAR™ Oil removal and gels

HAYFLOW™ Up to 5 times the life of standard bags

DURAGAF™ Up to 3 times the life of standard bags

SENTINEL® High quality, durable performance

UNIBAG™ Efficiency with an economical advantage

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118 Fax: (248) 377-3172

[email protected] www.tfsi1.com

223

LIQUID PROCESS FILTRATION - LIQUID BAG FILTER HOUSINGSSideline Liquid Bag Filter Housings

A SIDELINE housing is a solid, investment-cast filter in the medium cost range. A SIDELINE housing offers a standard eye-bolt closure and a choice of 2˝ or 3˝ ANSI flanged

connections as standard. For filter bags sizes 01, 02, 03 and 04. Type 304 or 316 stainless steel construction means superior corrosion resistance and consistent

performance, year after year. A smooth, bead-blasted finish, coupled with SIDELINE's minimum 2-weld design, makes it easy to completely clean the interior of the housing.

All SIDELINE housings come with an exclusive Five Year Warranty and the ASME code UM stamp.

SIDELINE housings... for all heavy duty industrial applications.

These value added features: Give these benefits

Side inlet with evacuation cover Less messy bag changing, no spillage of unfiltered liquid.

Cover opening direction can be changed in the field

Easily adapts to different piping layouts. Accommodates walls, posts or other obstructions.

Compression bag hold down 360 degree sealing of the filter bag to the housing.

Integral cover handle

Ergonomic and easy to open

Max. Allowable HousingPart Number No. Of

BagsBag Size Max. Flow 2

GPMMaterial 1 Pressure

(PSI)Temperature**

(ºF)Volume

(GAL)Weight

(LBS)Inlet OutletConnection

Type Vent 4 IN

SBF-0101-AB10-020A * 1 1 90 SS 150 400 4.75 84 2" Flanged 1/4"SBF-0101-AB10-030A * 1 1 90 SS 150 400 4.75 84 3" Flanged 1/4"SBF-0102-AB10-020A * 1 2 180 SS 150 400 8.5 102 2" Flanged 1/4"SBF-0102-AB10-030A * 1 2 180 SS 150 400 8.5 102 3" Flanged 1/4"SBF-0103-AB21-015N * 1 3 25 SS 300 225 0.5 26 1 1/2" NPT 1/4"SBF-0104-AB21-015N * 1 4 50 SS 300 225 0.7 29 1 1/2" NPT 1/4"

Dimensions In Inches Part Number A B C D E F

SBF-0101-AB10-020A * 17.70 19.50 3.15 8.62 8.66 54.70 SBF-0101-AB10-030A * 17.70 19.50 3.15 8.62 8.66 54.70 SBF-0102-AB10-020A * 17.70 35.00 3.15 8.62 8.66 85.50 SBF-0102-AB10-030A * 17.70 35.00 3.15 8.62 8.66 85.50 SBF-0103-AB21-015N * na 11.77 2.95 4.50 3.50 21.80 SBF-0104-AB21-015N * na 17.87 2.95 4.50 3.50 33.90

[

1) SS = Austenitic Stainless Steel SS 316 and CF8M or better 2) Maximum theoretical flow based on water viscosity, bag specific 3) Dimensions for reference only and approximate. Exact dimensions for installation purposes available on request. 4) For details, see available product specific data sheet

* Part number is for stainless steel construction. Change AB to CS for carbon steel. ** Depending on seal material

Product Codes D MBF 04 02 AC 10 050 D

D-DUOLINE M-MODULINE

VMBF-MAXILINE MBF-MAXILINE TBF-TOPLINE SBF-SIDELINE PBF-POLYLINE FBF-FLOWLINE EBF-ECOLINE

No. of bags 01, 02, 04, 08, 12, 16, 20, 24

Bag Size 01-short 7" 02-long 7" 03-short 4" 04-long 4"

Material AB-SS316 CS-Carbon Steel PO-Polypropylene PF-PVDF

Pressure rating 10-150 psi 21-300 psi

Connection Size 050-1/2" 010-1" 012-1 1/4" 015-1 1/2" 020-2" Up to 140-14"

Connection Type A-ANSI Flange N-NPT Female Thread

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118Fax: (248) 377-3172

[email protected] www.tfsi1.com

224

LIQUID PROCESS FILTRATION - LIQUID BAG FILTER HOUSINGSEcoline Liquid Bag Filter Housings

Max. Allowable HousingPart Number No. Of

BagsBag Size Max. Flow 2

GPMMaterial 1 Pressure

(PSI)Temperature**

(ºF)Volume

(GAL)Weight

(LBS)Inlet OutletConnection

Type Vent 4 IN

EBF-0101-AB10-020N * 1 1 90 SS 100 250 4 25 2" NPT 1/4"EBF-0102-AB10-020N * 1 2 180 SS 100 250 7 38 2" NPT 1/4"EBF-0103-AB10-015N * 1 3 25 SS 150 250 0.5 9 1 1/2" NPT 1/4"EBF-0104-AB10-015N * 1 4 50 SS 150 250 0.7 11 1 1/2" NPT 1/4"

Dimensions In Inches Part Number A B C D E F

EBF-0101-AB10-020N * na 19.64 3.24 7.68 5.37 37.00 EBF-0102-AB10-020N * na 35.19 3.24 7.68 5.37 68.00 EBF-0103-AB10-015N * na 11.77 2.78 4.50 3.50 22.45 EBF-0104-AB10-015N * na 17.87 2.78 4.50 3.50 33.84

11) SS = Austenitic Stainless Steel SS 316 and CF8M or better 2) Maximum theoretical flow based on water viscosity, bag specific 3) Dimensions for reference only and approximate. Exact dimensions for installation purposes available on request. 4) For details, see available product specific data sheet * Part number is for stainless steel construction. Change AB to CS for carbon steel. ** Depending on seal material

Product Codes D MBF 04 02 AC 10 050 D

D-DUOLINE M-MODULINE

VMBF-MAXILINE MBF-MAXILINE TBF-TOPLINE SBF-SIDELINE PBF-POLYLINE FBF-FLOWLINE EBF-ECOLINE

No. of bags 01, 02, 04, 08, 12, 16, 20, 24

Bag Size 01-short 7" 02-long 7" 03-short 4" 04-long 4"

Material AB-SS316 CS-Carbon Steel PO-Polypropylene PF-PVDF

Pressure rating 10-150 psi 21-300 psi

Connection Size 050-1/2" 010-1" 012-1 1/4" 015-1 1/2" 020-2" Up to 140-14"

Connection Type A-ANSI Flange N-NPT Female Thread

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118 Fax: (248) 377-3172

[email protected] www.tfsi1.com

225

LIQUID PROCESS FILTRATION - LIQUID BAG FILTER HOUSINGSMaxiline MBF HD Liquid Bag Filter Housings

MAXILINE™ MBF HD

The MAXILINE HD multi-bag filter housing features a cost effective, handwheel operated, davit cover. Loosen the swing bolts, turn the davit handwheel and swing the cover aside.

Standard ASME “U” Code Stamp. Tapered, electro-polished stainless steel perforated baskets. Unique 3-point hold-down or bayonet fittings ensure high quality of seal between

each filter bag and housing body. A special tool (supplied) ensures simple, effective operation.

Rugged, simple handwheel-operated davit cover makes the HD perfect for cost sensitive applications.

Hydraulic-assist davit cover is available as an option. Positive O-ring sealing provides easy, reliable operation. Available in carbon steel and Type 316 stainless steel for high corrosion resistance. 7 standard sizes with 3 through to 24 bag housings are available for size 02 filter bags.

These value added features: Give these benefits

Hand wheel operated davit cover Rugged, reliable and very cost effective.

Positive bag hold downs Perfect bag to housing sealing for no by-pass

Up to 24 bags per housing Can handle very high flow rate / high dirt load applications

Positive O ring seal

No external leakage

Max. Allowable HousingPart Number No. Of

BagsBag Size Max. Flow 2

GPMMaterial 1 Pressure

(PSI)Temperature**

(ºF)Volume

(GAL)Weight

(LBS)Inlet OutletConnection

Type Vent 4 IN

MBF-0302-AB10-030A-UT-11HD * 3 2 230 SS or CS 150 250 40 255 3" Flanged 1"MBF-0402-AB10-040A-UT-11HD * 4 2 400 SS or CS 150 250 54 390 4" Flanged 1"MBF-0602-AB10-060A-UT-11HD * 6 2 900 SS or CS 150 250 95 460 6" Flanged 1"MBF-0802-AB10-080A-UT-11HD * 8 2 1750 SS or CS 150 250 140 655 8" Flanged 1"MBF-1002-AB10-100A-UT-11HD * 10 2 2600 SS or CS 150 250 215 1400 10" Flanged 1"MBF-1202-AB10-100A-UT-11HD * 12 2 2600 SS or CS 150 250 245 1500 10" Flanged 1"MBF-1402-AB10-100A-UT-11HD * 14 2 2600 SS or CS 150 250 311 1800 10" Flanged 1"MBF-1602-AB10-120A-UT-11HD * 16 2 3500 SS or CS 150 250 317 1875 12" Flanged 1"MBF-1802-AB10-120A-UT-11HD * 18 2 3500 SS or CS 150 250 446 2420 12" Flanged 1"MBF-2002-AB10-140A-UT-11HD * 20 2 4500 SS or CS 150 250 454 2505 14" Flanged 1"MBF-2202-AB10-140A-UT-11HD * 22 2 4500 SS or CS 150 250 570 2730 14" Flanged 1"MBF-2402-AB10-140A-UT-11HD * 24 2 4500 SS or CS 150 250 570 2800 14" Flanged 1"

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118Fax: (248) 377-3172

[email protected] www.tfsi1.com

226

LIQUID PROCESS FILTRATION - LIQUID BAG FILTER HOUSINGSMaxiline MBF HD Liquid Bag Filter Housings

Dimensions In Inches Part Number A B C D E F

MBF-0302-AB10-030A-UT-11HD * 6.00 22.50 6.40 18.00 12.75 66.00

MBF-0402-AB10-040A-UT-11HD * 6.00 22.20 7.80 24.00 16.00 68.00

MBF-0602-AB10-060A-UT-11HD * 7.00 20.00 9.80 26.00 18.50 68.00

MBF-0802-AB10-080A-UT-11HD * 8.25 19.00 10.78 30.00 20.50 66.00

MBF-1002-AB10-100A-UT-11HD * 10.00 17.00 13.30 36.00 24.50 70.00

MBF-1202-AB10-100A-UT-11HD * 10.00 17.00 13.80 38.00 24.50 72.00

MBF-1402-AB10-100A-UT-11HD * 11.50 20.00 11.81 42.00 28.00 76.00

MBF-1602-AB10-120A-UT-11HD * 11.50 20.00 11.81 42.00 28.00 76.00

MBF-1802-AB10-120A-UT-11HD * 12.50 22.00 10.69 48.00 31.00 88.00

MBF-2002-AB10-140A-UT-11HD * 12.50 22.00 10.69 48.00 31.00 88.00

MBF-2202-AB10-140A-UT-11HD * 12.50 22.00 13.44 52.00 33.00 92.00

MBF-2402-AB10-140A-UT-11HD * 12.50 22.00 13.44 52.00 33.00 92.00

11) SS = Austenitic Stainless Steel SS 316 and CF8M or better 2) Maximum theoretical flow based on water viscosity, bag specific 3) Dimensions for reference only and approximate. Exact dimensions for installation purposes available on request. 4) For details, see available product specific data sheet * Part number is for stainless steel construction. Change AB to CS for carbon steel. ** Depending on seal material

Product Codes D MBF 04 02 AC 10 050 D

D-DUOLINE M-MODULINE

VMBF-MAXILINE MBF-MAXILINE TBF-TOPLINE SBF-SIDELINE PBF-POLYLINE FBF-FLOWLINE EBF-ECOLINE

No. of bags 01, 02, 04, 08, 12, 16, 20, 24

Bag Size 01-short 7" 02-long 7" 03-short 4" 04-long 4"

Material AB-SS316 CS-Carbon Steel PO-Polypropylene PF-PVDF

Pressure rating 10-150 psi 21-300 psi

Connection Size 050-1/2" 010-1" 012-1 1/4" 015-1 1/2" 020-2" Up to 140-14"

Connection Type A-ANSI Flange N-NPT Female Thread

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118 Fax: (248) 377-3172

[email protected] www.tfsi1.com

227

LIQUID PROCESS FILTRATION - LIQUID BAG FILTER HOUSINGSMaxiline MBF HE Liquid Bag Filter Housings

Max. Allowable HousingPart Number No. Of

BagsBag Size Max. Flow 2

GPMMaterial 1 Pressure

(PSI)Temperature**

(ºF)Volume

(GAL)Weight

(LBS)Inlet OutletConnection

Type Vent 4 IN

MBF-0302-AB10-030A-UT-11HE * 3 2 230 SS or CS 150 250 40 245 3" Flanged 1"MBF-0402-AB10-040A-UT-11HE * 4 2 400 SS or CS 150 250 69 380 4" Flanged 1"MBF-0602-AB10-060A-UT-11HE * 6 2 900 SS or CS 150 250 90 440 6" Flanged 1"MBF-0802-AB10-080A-UT-11HE * 8 2 1750 SS or CS 150 250 116 644 8" Flanged 1"

Dimensions In Inches Part Number A B C D E F

MBF-0302-AB10-030A-UT-11HE * 6.00 22.50 6.40 18.00 12.75 60.00 MBF-0402-AB10-040A-UT-11HE * 6.00 22.20 7.40 24.00 16.00 68.40 MBF-0602-AB10-060A-UT-11HE * 7.50 19.50 9.03 24.00 16.50 68.80 MBF-0802-AB10-080A-UT-11HE * 8.25 19.00 6.48 30.00 20.50 79.50

1) SS = Austenitic Stainless Steel SS 316 and CF8M or better 2) Maximum theoretical flow based on water viscosity, bag specific 3) Dimensions for reference only and approximate. Exact dimensions for installation purposes available on request. 4) For details, see available product specific data sheet * Part number is for stainless steel construction. Change AB to CS for carbon steel. ** Depending on seal material

Product Codes D MBF 04 02 AC 10 050 D

D-DUOLINE M-MODULINE

VMBF-MAXILINE MBF-MAXILINE TBF-TOPLINE SBF-SIDELINE PBF-POLYLINE FBF-FLOWLINE EBF-ECOLINE

No. of bags 01, 02, 04, 08, 12, 16, 20, 24

Bag Size 01-short 7" 02-long 7" 03-short 4" 04-long 4"

Material AB-SS316 CS-Carbon Steel PO-Polypropylene PF-PVDF

Pressure rating 10-150 psi 21-300 psi

Connection Size 050-1/2" 010-1" 012-1 1/4" 015-1 1/2" 020-2" Up to 140-14"

Connection Type A-ANSI Flange N-NPT Female Thread

Polyline Liquid Bag Filter HousingsMax. Allowable Housing

Part Number No. OfBags

Bag Size Max. Flow 2GPM

Material 1 Pressure(PSI)

Temperature**(ºF)

Volume(GAL)

Weight(LBS)

Inlet OutletConnection

Type Vent 4 IN

PBF-0101-PO10-020A * 1 1 50 PPL 150 70 6.6 55 2" Flanged 1/4"PBF-0101-PO10-020N * 1 1 50 PPL 150 70 6.6 51 2" NPT 1/4"PBF-0102-PO10-020A * 1 2 100 PPL 150 70 9.5 68 2" Flanged 1/4"PBF-0102-PO10-020N * 1 2 100 PPL 150 70 9.5 64 2" NPT 1/4"PBF-0102-PF07-020A * 1 2 100 PVDF 100 80 9.5 100 2" Flanged 1/4"D-PBF-0101-PO10-020A * 1+1 1 50 PPL/CPVC 150 70 14.5 162 2" Flanged 1/4"D-PBF-0101-PO10-020N * 1+1 2 100 PPL/CPVC 150 70 20.6 190 2" Flanged 1/4"

Dimensions In Inches Part Number A B C D E F

PBF-0101-PO10-020A * 3.26 20.75 3.38 10.35 8.50 60.00 PBF-0101-PO10-020N * 3.26 20.75 3.38 10.35 6.14 60.00 PBF-0102-PO10-020A * 3.26 36.75 3.38 10.35 8.50 76.00 PBF-0102-PO10-020N * 3.26 36.75 3.38 10.35 6.14 76.00 PBF-0102-PF07-020A * 3.26 36.00 3.88 10.35 8.50 75.25

D-PBF-0101-PO10-020A * 6.10 39.04 3.88 10.35 30.00 75.10 D-PBF-0101-PO10-020N * 6.10 55.04 3.88 10.35 30.00 91.10

1) SS = Austenitic Stainless Steel SS 316 and CF8M or better 2) Maximum theoretical flow based on water viscosity, bag specific 3) Dimensions for reference only and approximate. Exact dimensions for installation purposes available on request. 4) For details, see available product specific data sheet * Part number is for stainless steel construction. Change AB to CS for carbon steel. ** Depending on seal material

Product Codes D MBF 04 02 AC 10 050 D

D-DUOLINE M-MODULINE

VMBF-MAXILINE MBF-MAXILINE TBF-TOPLINE SBF-SIDELINE PBF-POLYLINE FBF-FLOWLINE EBF-ECOLINE

No. of bags 01, 02, 04, 08, 12, 16, 20, 24

Bag Size 01-short 7" 02-long 7" 03-short 4" 04-long 4"

Material AB-SS316 CS-Carbon Steel PO-Polypropylene PF-PVDF

Pressure rating 10-150 psi 21-300 psi

Connection Size 050-1/2" 010-1" 012-1 1/4" 015-1 1/2" 020-2" Up to 140-14"

Connection Type A-ANSI Flange N-NPT Female Thread

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118Fax: (248) 377-3172

[email protected] www.tfsi1.com

228

LIQUID PROCESS FILTRATION - LIQUID BAG FILTER HOUSINGSMaxiline VMBF SE Liquid Bag Filter HousingsQIC-LOCK™ MAXILINE™ VMBF SE

The user friendly, cost effective bag filter housing for high volume applications and processes demanding frequent bag change-out. Ideal for batch process runs and high dirt load applications.

QIC-LOCK rapid opening mechanism ensures simple, operator friendly and safe operation with minimal downtime to increase productivity and decrease running costs.

Unique 3-point hold down or bayonet fittings ensure high quality of seal between each filter bag and housing body. Special tool (supplied) ensures simple effective operation.

A counter-balanced spring assisted cover-lifting mechanism balances the cover perfectly giving it a weightless feel. Opening and closing of the cover with the "little finger" is a reality.

Positive O-ring sealing offers easy and safe operation. Side inlet and bottom outlet provides easy and full drainage, tangential outlet option available

to reduce housing height. Available in carbon steel or Type 316 stainless steel for high corrosion resistance. Housing volume is optimized to minimize product loss. 6 standard sizes with 4 through to 24 bag housings available (size 02).

These value added features: Give these benefits

QIC-LOCK spindle mechanism

Operator friendly, simple, fast bag change-out. Ideal for processes requiring frequent bag changes such as batch processes.

Automatic safety interlock for venting housing Cover cannot be opened if housing is under pressure.

Low profile design with tangential inlet/outlet. Reduces housing height to make bag changing easier. No need for ladders, stools or catwalks.

Spring assisted cover lifter

Quick, easy opening of even the largest size covers by a single person.

Max. Allowable HousingPart Number No. Of

BagsBag Size Max. Flow 2

GPMMaterial 1 Pressure

(PSI)Temperature**

(ºF)Volume

(GAL)Weight

(LBS)Inlet OutletConnection

Type Vent 4 IN

VMBF-0402-AB10-040A-UT-11SE * 4 2 400 SS 150 250 69 484 4" Flanged 1"VMBF-0602-AB10-060A-UT-11SE * 6 2 900 SS 150 250 139 983 6" Flanged 1"VMBF-0802-AB10-080A-UT-11SE * 8 2 1750 SS 150 250 141 1023 8" Flanged 1"

Dimensions In Inches A B C D E F

6.00 20.00 10.50 22.00 15.75 68.00 7.25 20.00 13.00 31.50 20.75 80.00 8.25 19.00 12.80 31.50 20.50 80.00

1) SS = Austenitic Stainless Steel SS 316 and CF8M or better 2) Maximum theoretical flow based on water viscosity, bag specific 3) Dimensions for reference only and approximate. Exact dimensions for installation purposes available on request. 4) For details, see available product specific data sheet * Part number is for stainless steel construction. Change AB to CS for carbon steel. ** Depending on seal material

Product Codes D MBF 04 02 AC 10 050 D

D-DUOLINE M-MODULINE

VMBF-MAXILINE MBF-MAXILINE TBF-TOPLINE SBF-SIDELINE PBF-POLYLINE FBF-FLOWLINE EBF-ECOLINE

No. of bags 01, 02, 04, 08, 12, 16, 20, 24

Bag Size 01-short 7" 02-long 7" 03-short 4" 04-long 4"

Material AB-SS316 CS-Carbon Steel PO-Polypropylene PF-PVDF

Pressure rating 10-150 psi 21-300 psi

Connection Size 050-1/2" 010-1" 012-1 1/4" 015-1 1/2" 020-2" Up to 140-14"

Connection Type A-ANSI Flange N-NPT Female Thread

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118 Fax: (248) 377-3172

[email protected] www.tfsi1.com

229

LIQUID PROCESS FILTRATION - LIQUID BAG FILTER HOUSINGSDuoline / Moduline / Topline Liquid Bag Filter Housings DUOLINE™ Filter Housings

Duplex units for continuous filtration processes.

The DUOLINE bag filter system consists of two bag filter housings (SIDELINE housing or TOPLINE housing) fitted together at the inlet and outlet by either a butterfly or ball valve assembly. Valve assemblies are connected together by a center post handle assembly in order to guarantee a synchronized change from filter A to filter B. A quick turn of the handle diverts the flow from one filter housing to the other. The filtration process runs continuously during bag change-outs. MODULINE™ Filter Housings

Double or modular multibag unit for larger flow rates.

The MODULINE filter housings are multibag units assembled from two or more standard SIDELINE (MSBF) or TOPLINE (MTBF) housings using standard elbows, manifolds or T-Pipe modules. The MODULINE filter concept offers greater flexibility, capacity can be easily increased by adding further modules. MODULINE housings are fabricated to customer specifications. TOPLINE™ Dual Filter Housings

Compact 2-bag unit with single cover-lid.

The TOPLINE TBF-02 filter housing combines the advantages of the TOPLINE housing series with a compact 2-bag design. Features a single cover-lid, eye-bolt closure and standard adjustable leg assembly.

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118Fax: (248) 377-3172

[email protected] www.tfsi1.com

230

LIQUID PROCESS FILTRATION - LIQUID BAG FILTER HOUSINGSDuoline / Moduline / Topline Liquid Bag Filter Housings

Max. Allowable HousingPart Number No. Of

BagsBag Size Max. Flow 2

GPMMaterial 1 Pressure

(PSI)Temperature**

(ºF)Volume

(GAL)Weight

(LBS)Inlet OutletConnection

Type Vent 4 IN

TOPLINE * 2 2 180 SS or CS 150 250 16 240 2" Flanged 1/4"SIDELINE * 2 2 180 SS 150 250 16 300 2" Flanged 1/4"SIDELINE * 2 2 180 SS 150 250 17 330 3" Flanged 1/4"FLOWLINE * 2 2 180 SS or CS 150 250 15 200 2" Flanged 1/4"TOPLINE * 1+1 2 360 SS or CS 150 250 16 230 2" Flanged 1/4"SIDELINE * 1+1 2 360 SS 150 250 16 230 2" Flanged 1/4"SIDLINE * 1+1 2 360 SS 150 250 17 300 3" Flanged 1/4"FLOWLINE * 1+1 2 360 SS or CS 150 250 15 170 2" Flanged 1/4"TBF-0101-AB10-020A * 1 1 90 SS or CS 150 400 3.5 80 2" Flanged 1/4"TBF-0102-AB10-020A * 1 2 180 SS or CS 150 400 7.25 93 2" Flanged 1/4"TBF-0102-AB10-020R-M32B0 * 1 2 180 SS 150 400 7.25 93 2" Tri-Clamp 1/4"

Dimensions In Inches Part Number A B C D E F TOPLINE * 17.70 24.50 1.93 8.62 37.45 84.25

SIDELINE * 17.70 27.50 3.15 8.62 30.82 85.50

SIDELINE * 17.70 27.50 3.15 8.62 33.32 85.50

FLOWLINE * 17.70 28.44 3.34 7.68 37.45 85.50

TOPLINE * 17.70 24.50 1.93 8.62 34.32 84.25

SIDELINE * 17.70 27.50 3.15 8.62 27.44 85.50

SIDLINE * 17.70 27.00 3.15 8.62 29.70 85.50

FLOWLINE * 17.70 28.44 3.34 7.68 26.64 85.50

TBF-0101-AB10-020A * 17.70 15.50 1.93 8.62 12.08 53.50

TBF-0102-AB10-020A * 17.70 31.00 1.93 8.62 12.08 84.25

TBF-0102-AB10-020R-M32B0 * 15.80 32.78 1.93 8.62 12.83 84.25

1) SS = Austenitic Stainless Steel SS 316 and CF8M or better 2) Maximum theoretical flow based on water viscosity, bag specific 3) Dimensions for reference only and approximate. Exact dimensions for installation purposes available on request. 4) For details, see available product specific data sheet * Part number is for stainless steel construction. Change AB to CS for carbon steel. ** Depending on seal material

Product Codes D MBF 04 02 AC 10 050 D

D-DUOLINE M-MODULINE

VMBF-MAXILINE MBF-MAXILINE TBF-TOPLINE SBF-SIDELINE PBF-POLYLINE FBF-FLOWLINE EBF-ECOLINE

No. of bags 01, 02, 04, 08, 12, 16, 20, 24

Bag Size 01-short 7" 02-long 7" 03-short 4" 04-long 4"

Material AB-SS316 CS-Carbon Steel PO-Polypropylene PF-PVDF

Pressure rating 10-150 psi 21-300 psi

Connection Size 050-1/2" 010-1" 012-1 1/4" 015-1 1/2" 020-2" Up to 140-14"

Connection Type A-ANSI Flange N-NPT Female Thread

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118 Fax: (248) 377-3172

[email protected] www.tfsi1.com

231

LIQUID PROCESS FILTRATION - LENTICULARGusmer - Cellu-Stack

Cellu-Stack® Product Line Overview

Applications Food / Beverage - Beer, Distilled Spirits, Juice, Wine Chemicals - Specialty, Fine Cosmetics Dielectric Fluids Dyes Flavors Fragrances Gelatin Inks Photographic Solutions Photoresist Solutions Utility Gusmer Enterprises’ Cellu-Stacks are a convenient way to utilize depth filtration media in an enclosed system. Offered in all Gusmer media types, these stack filters can be used for coarse, fine, and pre-sterile filtration in numerous filtration applications.

Each Cellu-Stack filter cell is independently sealed through an injection molding process. Edge seal bosses are incorporated as a special feature to prevent cell collapse during prolonged filtration runs. Specially designed anti-rotating spacers are placed between the cells and the entire unit is pre–compressed and sealed in a module format by a series of stainless steel straps.

Multiple stacks can be arranged within a housing to form a leak-free, convenient filtration system with exceptional filtration surface area and particle retention.

Cellu-Stack filters are designed for ease in loading and unloading filter housings. This significantly reduces operating costs and production downtime.

Cellu-Stack filters are assembled under sufficient compression to maintain integrity into 12- or 16- cell configurations. Depending on your filtration needs, a variety of optional gasket materials are available.

Cellu-Stack Advantages Full range of filter media types with high adsorptive and retention properties Clean and safe filtration method when dealing with elevated pressures, temperatures, vapors, etc. Convenient operations with short set-up or changeover times Small process footprint Stack design meets USP Class VI test requirements Designed to comply with GMP practices and procedures Highly economical with minimal maintenance and low operating costs Protection of filtrate against spoilage in enclosed depth filtration system No product drip losses

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118Fax: (248) 377-3172

[email protected] www.tfsi1.com

232

LIQUID PROCESS FILTRATION - LENTICULARGusmer - Cellu-Stack

MEDIA OFFERINGS Gusmer’s standard media series offer a broad range of material options to best meet our customer’s needs.

Media Overview

Cellupore® 1300 Series

All cellulose filter series is a blend of refined cellulose fibers and offers enhanced contaminant loading capacity. For liquid filtration applications where filter aids such as diatomaceous earth or perlites are not suitable. This filter series is the best option for low extractables, high wet strength, and increased throughput.

1330AO / 1330GO Utility Series These specialized filters are designed as dielectric fluid reconditioning filters. The AO grade is specifically designed with an advanced absorbent layer for high capacity water removal.

Carbac® 1600 Carbon Series

Carbon gradient density filter sheets have high adsorptive capacities with superior throughput capacity. The sheets are comprised of the finest charge-modified cellulose pulps, activated carbon, and inorganic filter aids. These grades are particularly suitable for decolorization, odor, and flavor removal.

Cellupore® 1700W Series

These depth filters are designed to cover the full range of applications from coarse, polish, and pre-sterile filtration for the food and beverage industry. Exhibiting a positive zeta potential, the mixtures of cellulose and inorganic filter aids provide reliable filtration performance for all applications.

Cellupore® 1900 Series

The Cellupore 1900 series has enhanced filtration performance with high wet strength with low extractables. The gradient density filters are manufactured under strict process and quality controls to ensure uniform and consistent filtration performance. The specially designed combination of highly refined pulp and inorganic filter aids results in a filter series that meets USP XXIII Class VI requirements.

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118 Fax: (248) 377-3172

[email protected] www.tfsi1.com

233

LIQUID PROCESS FILTRATION - LENTICULARGusmer - Cellu-Stack

STACK CONSTRUCTION Cellu-Stacks® are available in multiple sizes and configurations. Each stack is constructed from individual cells of Gusmer Cellupore media assembled in a pre-compressed format (see below). The cells are sealed by three 316 stainless steel bands with propylene flow separators and edge seals. Multiple gasket materials are available to need your compatibility and application needs. STACK SPECIFICATIONS

Max. Operating Temp. 1760F (800C) Steam in Place - 3 cycles 2530F (1230C) Max. Differential Pressure 30 psid (2.1 bar) Recommended Rinse Volume 2.5 gal/ft2

(100L/m2)

All Cellupore depth filter sheet grades are available in Cellu-Stack formats. The stack configurations are manufactured in 12” (284 mm) and 16” (410 mm) diameters).

Configuration Cellu-Stack Materials of Construction

Effective Filtration Surface Area

12” diameter, 16 cell Propylene edge seal, end rings 17.7 ft2 16” diameter, 16 cell Propylene edge seal, end rings 38.0 ft2

Note: Custom stack configurations with a different number of cells are available upon request following validation.

CELLU-STACK ORDERING GUIDE

Note: “X” indicates grade is available but has not been

validated. Validation is available upon request.

1216- 12” 16 cell stack NT- Nitrile 13- 1300 05- SD- Standard 1616- 16” 16 cell stack SI- Silicone 16- 1600 10- NP- Neoprene 17- 1700W 15- P- Pharma FC- Fluorocarbon 19- 1900 20- EP- Ethylene 25-

Propylene Rubber 30-

CRM- 35-

40- DC-

45-

50-

55-

60-

65-

70-

Example: To order a 1900 Series 12˝ 16-cell Cellu-Stack filter with standard gaskets in a 65-flow standard grade, the order should read as follows: 1216-NT-1965SD. 75-

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118Fax: (248) 377-3172

[email protected] www.tfsi1.com

234

LIQUID PROCESS FILTRATION - LENTICULARGusmer - Cellu-Stack Housings

Gusmer Enterprises offers a complete line of Cellu-Stack housings designed as a cost effective system for high capacity liquid filtration applications. The versatile housing line is offered in Industrial, Sanitary Style Industrial, and Sanitary models to accommodate either 12” or 16” diameter Cellu-Stack filter modules. All housings are available in 1, 2, 3, or 4 stack versions which can be modified with the use of Cellu-Stack take-up adapters to accept fewer stacks for partial batch runs or other applications requiring fewer stacks. ASME code housings are also available if required.

TYPICAL APPLICATIONS Cosmetics Decolorization Electroplating Solutions Enzymes Fine Chemical Purification Flavor and Fragrances Food and Beverage Photographic Solutions Printing Inks

DESIGN FEATURES All wetted surfaces are 316L Stainless Steel. Unique removable center post assembly retained by exterior bolts. Center post guide rods are welded to perimeter of outlet port. No threaded parts are exposed to the product being filtered. Vent valve and gauge assembly is removable from housing dome to facilitate easy and thorough cleaning. Maximum operating pressure: 125 psi @ 250°F (8.79 Kgf/cm2 @ 121°C).

BENEFITS Eye bolt clamping system for fast stack change-outs and secure dome closure. Removable center post assembly for quick and thorough cleaning. Base plate design minimizes product hold-up volume and facilitates thorough cleaning. Adapters are available to allow operation with fewer stacks for partial batch runs. Spring assisted follower tube maintains a positive stack seal. Compact design requires minimal floor space. Units can be skid mounted for mobility.

External Finish Industrial Sanitary Sanitary Style Industrial

Passivated and electropolished, <35 Ra

Sanitary Passivated and electropolished, <25 Ra, Welds ground

Interior Finish Industrial Beadblast & passivated Sanitary Style Industrial

Passivated and electropolished, <25 Ra

Sanitary Passivated and electropolished, <20 Ra, Welds ground

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118 Fax: (248) 377-3172

[email protected] www.tfsi1.com

235

LIQUID PROCESS FILTRATION - LENTICULARGusmer - Cellu-Stack Housings

HOUSING SPECIFICATIONS

DIMENSIONS (inches) Housing

Style A B C D E

1-HIGH 2-HIGH 3-HIGH 4-HIGH 1-HIGH 2-HIGH 3-HIGH 4-HIGH IN-12 22.00 32.00 42.00 52.00 33.50 43.50 53.50 63.50 11.50 12.75 .25 FNPT SI-12 22.00 32.00 42.00 52.00 33.50 43.50 53.50 63.50 11.50 12.75 1.5 TRI-CLAMP SA-12 22.00 32.00 42.00 52.00 33.50 43.50 53.50 63.50 11.50 12.75 1.5 TRI-CLAMP IN-16 21.00 31.00 41.00 51.00 32.50 42.50 52.50 62.50 11.50 18.00 .25 FNPT SI-16 21.75 31.75 41.75 51.75 33.25 43.25 53.25 63.25 11.50 18.00 1.5 TRI-CLAMP SA-16 22.00 32.00 42.00 52.00 33.50 43.50 53.50 63.50 11.50 18.00 1.5 TRI-CLAMP

IN - Industrial SI - Sanitary Style Industrial SA - Sanitary (welds ground)

WEIGHTS & VOLUMES Housing

Style Dome Weight (lbs) Approximate Liquid Capacity* (gal) Approximate Shipping Weight (lbs)

1-HIGH 2-HIGH 3-HIGH 4-HIGH 1-HIGH 2-HIGH 3-HIGH 4-HIGH 1-HIGH 2-HIGH 3-HIGH 4-HIGH IN-12 30 38 46 54 8.3 13.5 18.8 24.0 112 120 128 136 SI-12 30 38 46 54 8.3 13.5 18.8 24.0 112 120 128 136 SA-12 35 43 51 59 8.3 13.5 18.8 24.0 130 138 146 154 IN-16 47 60 73 86 14.5 25.3 36.0 46.8 272 285 298 311 SI-16 47 60 73 86 14.5 25.3 36.0 46.8 272 285 298 311 SA-16 54 71 88 105 14.5 25.3 36.0 46.8 304 321 338 355

Liquid capacities based on a full complement of Cellu-Stacks loaded into housing

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118Fax: (248) 377-3172

[email protected] www.tfsi1.com

236

LIQUID PROCESS FILTRATION - LENTICULARGusmer - Cellu-Stack Housings

CELLU-STACK® HOUSING ORDER GUIDE

Example: To order a standard 12” 1-HIGH Industrial housing with standard connections, gaskets, and surface finish, the order should read as follows: IN-121-NNEBP

SPARE PARTS LIST

Center Post 1-HIGH 2-HIGH 3-HIGH 4-HIGH

Industrial INCP-1H INCP-2H INCP-3H INCP-4H Beadblast and passivated finish; includes gasket and bolts

Sanitary Style Industrial

INCP-1H-EP INCP-2H-EP INCP-3H-EP INCP-4H-EP Electropolished finish; includes gasket and bolts

Sanitary SACP-1H SACP-2H SACP-3H SACP-4H Electropolished finish; includes gasket, o-ring and bolts

Industrial Sanitary Seal Kit 12" 16" 12" 16" Silicone 12-INSK-S 16-INSK-S 12-SASK-S 16-SASK-S EPDM 12-INSK-E 16-INSK-E 12-SASK-E 16-SASK-E Viton 12-INSK-V 16-INSK-V 12-SASK-V 16-SASK-V

Kit includes all replacement o-rings, gaskets, retainer bolts and washers.

Follower Tube Assembly Part Designation Complete Follower Assembly (contains next 4 items)

FNSLA001

Filter nut – Delrin® FNSL001 Follower tube – Delrin® w/silicone o-ring FOL001 Follower tube spring – electropolished SP001 Filter nut rod FNR001

Pressure Gauge & Vent Assembly

Part Designation

Industrial IN-VENT-ASSY Sanitary Style Industrial SA-VENT-ASSY Sanitary SA-VENT-ASSY

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118 Fax: (248) 377-3172

[email protected] www.tfsi1.com

237

LIQUID PROCESS FILTRATION - STRAINERSModel 72 Simplex Basket Strainer

Sizes 3/8" to 8" Iron, Bronze, Carbon Steel, or Stainless Steel Threaded or Flanged

FEATURES

Quick open cover—no tools needed Heavy wall construction Large capacity baskets Machined basket seat Threaded drain Perforated or mesh 316 stainless basket Mounting feet for stable installation for

flanged units 2" and larger

OPTIONS

Basket perforations from 1/32" to 1/2" Basket mesh from 20 to 400 Monel baskets Viton, PTFE-encapsulated, or EPDM seals Vent valves Gauge/vent taps – 1/4" NPT Magnetic basket inserts Pressure differential gauge and switch

The Eaton Model 72 has been the industry standard simplex basket strainer for more than 75 years. It is perfect for industrial and commercial applications in which the line can be temporarily shut down for strainer basket cleaning or changeout. A reason for its popularity is the unusually large basket capacity. The free straining area with a perforated basket is a minimum of six times the cross sectional pipe area. No tools are needed to open the cover. The quick opening, swinging yoke can be disassembled and the basket removed in seconds. On sizes 4" and larger, a special cover clamp is provided to distribute

the seating pressure and to ensure positive seating of the cover. Another feature is a threaded drain on every size strainer (fitted with a plug). Sizes 2" and larger are equipped with legs that bolt to the floor for rock solid installation. Wall thicknesses are exceptionally heavy. The basket seats are precision machined to give a tight seal and prevent any material from bypassing the basket. The Eaton Model 72 simplex basket strainer is a top quality, heavy-duty unit designed to stand up to the most demanding of applications.

Model 72 Simplex

Size Material End Connection

Seals Pressure Rating

3/8" to 3" Iron and Bronze Threaded Buna-N 200 psi @ 100°F 1" to 3" Carbon Steel Threaded Buna-N 200 psi @ 100°F 1" to 3" Stainless Steel Threaded Viton® 200 psi @ 100°F 1" to 8" Iron Flanged 125# Buna-N 200 psi @ 100°F 1" to 8" Bronze Flanged 150# Buna-N 200 psi @ 100°F 1" to 8" Carbon Steel Flanged 150# Buna-N 200 psi @ 100°F 1" to 8" Stainless Steel Flanged 150# Viton® 200 psi @ 100°F

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118Fax: (248) 377-3172

[email protected] www.tfsi1.com

238

LIQUID PROCESS FILTRATION - STRAINERSModel 72 Simplex Basket Strainer

Threaded model 72 dimensions (in/mm) Dimensions and weights are for reference only. Contact Eaton for certified drawings.

------------------Net Wt (lbs / kg) ----------------- Mod. 72Cv Factors* Carbon Stainless

Size A B C D E F G H Bronze Steel Iron Steel Size Value Size Value

3/8 4.00 / 102 6.63 / 168 2.88 / 73 4.00 / 102 2.38 / 60 – 3/8 1 / 279 4 / 1.8 – 4 / 1.8 – 3/8" 15.0 2" 73 1/2 4.00 / 102 6.63 / 168 2.88 / 73 4.00 / 102 2.38 / 60 – 3/8 1 / 279 4 / 1.8 – 4 / 1.8 – 1/2" 15.0 2-1/2" 125 3/4 5.38 / 137 8.38 / 213 4.00 / 102 5.00 / 127 3.06 / 78 – 1/2 3 / 330 8 / 3.6 – 7 / 3.2 – 3/4" 15.0 3" 180 1 5.38 / 137 8.38 / 213 4.00 / 102 5.00 / 127 3.06 / 78 – 1/2 3 / 330 8 / 3.6 7 / 3.2 7 / 3.2 7 / 3.2 1" 22.5 4" 350

1-1/4 6.75 / 172 9.88 / 251 4.88 / 124 5.88 / 149 3.88 / 99 – 1/2 4 / 356 13 / 6 – 12 / 6 – 1-1/4" 31.5 6" 900 1-1/2 7.25 / 184 11.00 / 2794.88 / 124 7.00 / 178 4.00 / 102 – 3/4 6 / 406 16 / 7 15 / 7 15 / 7 16 / 7.3 1-1/2" 46.0 8" 1400

2 8.75 / 222 13.38 / 3406.75 / 172 7.63 / 194 5.13 / 130 – 1-1/421 / 533 32 / 15 36 / 16 28 / 13 31 / 14 2-1/2 10.38 / 26414.88 / 3788.00 / 203 8.63 / 219 6.38 / 162 – 1-1/2 26 / 660 49 / 22 52 / 24 42 / 19 51 / 23

* For water with clean, perforated basket

3 11.50 / 29217.75 / 4688.00 / 203 11.38 / 298 6.63 / 168 – 1-1/228 / 711 60 / 27 60 / 27 52 / 23 60 / 27

Flanged model 72 dimensions (in/mm) ------------------Net Wt (lbs / kg) ----------------- Carbon Stainless

Size A B C D E F G H Bronze Steel Iron Steel 1 7.63 / 194 8.38 / 213 4.00 / 102 5.00 / 127 – – 1/2 13.00 / 330 16 / 7 9 / 4 9 / 4 9 / 4

1-1/2 10.25 / 260 11.00 / 279 4.88 / 124 7.00 / 178 – – 3/4 16.00 / 406 30 / 14 17 / 7.7 17 / 7.7 17 / 7.7 2 10.50 / 268 13.75 / 349 6.75 / 172 7.63 / 194 5.13 / 130 6.25 / 159 3/8 20.00 / 508 49 / 22.3 36 / 16 36.5 / 17 36 / 16

2-1/2 11.63 / 295 15.63 / 397 8.00 / 203 8.88 / 226 6.38 / 162 7.63 / 194 3/8 23.00 / 584 64 / 29.1 63 / 27 54 / 25 63 / 29 3 13.13 / 334 18.00 / 457 8.00 / 203 10.63 / 270 6.50 / 165 8.00 / 203 3/8 27.00 / 686 85 / 38.6 – 76 / 35 – 3 13.13 / 334 18.75 / 476 7.94 / 202 12.00 / 305 6.50 / 165 8.00 / 203 1/2 27.00 / 686 – 86 / 39 – 86 / 39 4 16.75 / 425 19.88 / 505 10.75 / 273 10.75 / 273 9.63 / 245 11.38 / 289 1/2 30.00 / 762 140 / 63.6 – 125 / 55 – 4 17.25 / 438 19.88 / 505 10.69 / 272 10.69 / 272 9.25 / 235 11.38 / 289 1/2 30.00 / 762 – 130 / 59 – 130 / 59 5 18.13 / 461 25.13 / 638 10.75 / 273 15.25 / 387 10.00 / 254 11.38 / 289 1/2 41.00 / 1041 182 / 82.7 – 170 / 775 – 6 19.63 / 499 28.50 / 724 10.69 / 272 18.38 / 467 10.00 / 254 11.38 / 289 1/2 46.00 / 1168 270 / 122.7 235 / 107 200 / 91 235 / 107 8 27.00 / 686 40.50 / 1029 – 27.00 / 686 13.75 / 349 17.50 / 445 1/2 60.00 / 1524 600 / 272.7 550 / 250 500 / 227 550 / 250

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118 Fax: (248) 377-3172

[email protected] www.tfsi1.com

239

LIQUID PROCESS FILTRATION - STRAINERSModel 53 Ball Type Duplex Basket Strainer

Sizes 3/4" to 4" Iron, Bronze, Carbon Steel, or Stainless Steel Threaded or Flanged

Unique diverter cartridge assures leak-tight isolation of basket chamber during cleaning.

A double sealing system on the upper and lower stems guards against any possible leakage. If service becomes necessary, just remove four bolts and the cartridge slides right out the top of the strainer body. FEATURES Dynamic sealing design for long life Easy-to-operate lever handle—no

gear box required Unique seat and seal design requires

no adjustments Teflon® seats for longer service life Foot pads for rock solid installation Double-stem O-rings for positive

sealing Easy to access body vent valve Side drain plugs on each basket well Piston seal strainer basket cover Easy access for diverter cartridge

removal 316 stainless steel ball design

Continuous Operation Eaton's model 53BTX duplex basket strainer can operate continuously, eliminating the need to shut down processes for cleaning of strainers. When the first basket is full, a unique flow diverter cartridge shifts flow to a second basket to permit removal and cleaning with no interruption to operations.

Draining this chamber is easy; the cover lifts and swings clear of the chamber opening with no special tools required.

The unique flow diverter cartridge prevents fluid bypass into the out-of-service chamber. It features a dynamic sealing system that ensures exceptionally long seat life and positive sealing. Manual internal or external ball support adjustments are not necessary.

Size and Material The compact, low-profile Model 53BTX fits into spaces ordinary strainers may not, yet it still uses full-size strainer baskets with a low-pressure drop performance. Eaton offers basket openings from 3/4" down to 45 microns. Type 316 stainless steel is standard and Monel or Hastelloy C materials are optional.

East Basket Servicing One drain plug is on each side of the basket. Additionally, an easy to access vent valve is on top of each basket well cover. Standard foot-mounting pads ensure a rock solid installation no matter where the strainer operates.

Available Options Include: Differential pressure gauges,

with or without switches Magnetic separators

installed in the strainer basket for removing fine ferrous particulate matter from the process media

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118Fax: (248) 377-3172

[email protected] www.tfsi1.com

240

LIQUID PROCESS FILTRATION - STRAINERSModel 53 Ball Type Duplex Basket Strainerp

Selection Table

Cv Factors* Size Value Size Value

3/4" 13 2" 42 Size Body &

Cartridge Material

End Connection Seat/Seal Diverter

Balls

Pressure Rating

PSIG @ 150°F 1" 13 2-1/2" 65

3/4", 1", 1-1/4", 1-1/2", 2", 2-1/2" Iron Threaded TFE/ Buna-N* Stainless Steel 200 psi @ 150°F 1-1/4" 18 3" 110

3/4", 1", 1-1/4", 1-1/2", 2", 2-1/2" Bronze Threaded TFE/ Buna-N* Stainless Steel 200 psi @ 150°F 1-1/2" 25 4" 175

3/4", 1", 1-1/4", 1-1/2", 2" Carbon Steel Threaded TFE/ Buna-N* Stainless Steel 200 psi @ 150°F * For water with clean, perforated baske

3/4", 1", 1-1/4", 1-1/2", 2" Stainless Steel Threaded TFE/ Viton® Stainless Steel 200 psi @ 150°F 1", 1-1/2", 2", 2-1/2", 3", 4" Iron Flanged 125# TFE/ Buna-N* Stainless Steel 200 psi @ 150°F 1", 1-1/2", 2", 2-1/2", 3", 4" Bronze Flanged 150# TFE/ Buna-N* Stainless Steel 200 psi @ 150°F 1", 1-1/2", 2", 2-1/2", 3", 4" Carbon Steel Flanged 150# TFE/ Buna-N* Stainless Steel 200 psi @ 150°F 1", 1-1/2", 2", 2-1/2", 3", 4" Stainless Steel Flanged 150# TFE/ Viton® Stainless Steel 200 psi @ 150°F

*Viton® standard for SSTL, optional for iron, bronze and carbon steel.

Front view Flanged and Threaded models

Dimensions (in/mm)

Weight – Iron Weight – Bronze Weight – Carbon & SS Pipe Flanged Threaded Flanged Threaded Flanged ThreadedSize AF AT C E F G H J K L (lb / kg)) (lb / kg) (lb / kg) (lb / kg) (lb / kg) (lb / kg) 3/4 5.50 / 140 5.00 / 127 13.38 / 340 10.50 / 268 3.25 / 83 2.13 / 54 1.63/ 41 2.75/ 70 3/8 – 37 / 17 — 46 / 21 – 41 / 19

1 6.88 / 175 5.50 / 140 5.00 / 127 13.38 / 340 10.50 / 268 3.25 / 83 2.13 / 54 1.63/ 41 2.75/ 70 3/8 42 / 19 37 / 17 52 / 24 46 / 21 47 / 21 41 / 19

1-1/4 6.88 / 175 7.50 / 190 6.81 / 173 17.00 / 432 13.25 / 330 3.25 / 83 2.13 / 54 1.63/ 41 2.75/ 70 3/8 – 80 / 36 – 100 / 45 – 89 / 40

1-1/2 9.38 / 238 7.50 / 190 6.81 / 173 17.00 / 432 13.25 / 330 3.25 / 83 2.13 / 54 1.63/ 41 2.75/ 70 3/8 90 / 41 80 / 36 113 / 51 100 / 45 100 / 45 89 / 40

2 10.63 / 270 10.00 / 254 8.38 / 213 21.75 / 552 17.38 / 441 4.69 / 119 2.50/ 64 1.81/ 46 4.00/ 102 5/8 167 / 76 157 / 71 209 / 95 197 / 90 185 / 84 174 / 79

2-1/2 10.75 / 273 10.00 / 254 8.38 / 213 21.75 / 552 17.37 / 441 4.69 / 119 2.50/ 64 1.81/ 46 4.00/ 102 5/8 183 / 83 157 / 71 229 / 104 197 / 90 203 / 92 –

3 13.50 / 343 8.88 / 226 26.50 / 673 22.75 / 578 4.69 / 119 2.50/ 64 1.81/ 46 4.00/ 102 5/8 285 / 129 – 357 / 162 – 432 / 196 –

4 16.00 / 406 13.25 / 337 33.00 / 838 24.75 / 629 5.19 / 132 3.94/ 100 3.25/ 83 4.50/ 114 5/8 389 / 177 – 487 / 221 – 432 / 196 –

Dimensions and weights are for reference only. Contact Eaton for certified drawings. Pressure equalizing valve and piping standard on 4" Model 53BTX duplex strainers.

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118 Fax: (248) 377-3172

[email protected] www.tfsi1.com

241

LIQUID PROCESS FILTRATION - STRAINERSModel 50 Plug Type Duplex Basket Strainer

Sizes 5", 6", 8" Iron, Bronze, Carbon Steel, or Stainless Steel Flanged

FEATURES Continuous flow, no shutdown for basket cleaning Rugged tapered plug design Lift jack prevents galling of the plug Quick open cover—no tools needed Large capacity baskets Threaded drain Machined basket seat Perforated or mesh 316 stainless steel basket

OPTIONS Ductile iron construction Basket perforations from

1/32" to 1/2" Basket mesh from 20 to 400 Monel baskets Vent valves Drain valves Gauge/vent taps - 1/4" NPT Magnetic basket inserts

Pressure differential gauge and switch connections Viton, PTFE encapsulated, or EPDM seals Cast iron and stainless steel diverter plug

Trouble-free Design, Easy Operation The Eaton Model 50 plug type duplex strainer's design is simple and economical. This high quality strainer is, in fact, a pressure rated plug valve with integral straining baskets. To switch the flow from one basket to the other, the operating handle moves through a 90-degree arc. Because of the unique port design in the diverter plug, it is impossible for this operation to stop the flow. The entire switching operation takes fewer than 30 seconds, no tools required. Positioning the plug each time in exactly the right spot happens automatically by integral stops. Before operating the handle, a specially designed, manual lifting jack built into the strainer, lifts the diverter plug

off its seat. After the switching operation, the jack easily reseats the plug, even under high pressures. Because a built-in stop limits the distance the diverter plug rises, it minimizes the possibility of material bypassing the plug while rotated to divert flow. It also prevents debris from building up under the plug and making it difficult to reseat. Other Features A quick, easy to open,

swing-away yoke design cover goes back on just as fast as it came off

Standard NPT drain taps simplify the draining of the basket chamber

All sizes come with mounting legs for bolting

the strainer to the floor for a rock solid installation

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118Fax: (248) 377-3172

[email protected] www.tfsi1.com

242

LIQUID PROCESS FILTRATION - STRAINERSModel 50 Plug Type Duplex Basket StrainerSelection chart

Size Body Material Plug Material End Connections Seals 5", 6", 8" Iron Bronze Flanged 125# Buna-N 5", 6", 8" Bronze Bronze Flanged 150# Buna-N

6", 8" Carbon Steel Bronze Flanged 150# Buna-N 6", 8" Stainless Steel Stainless Steel Flanged 150# Viton®

DIN flanges available on 6" only

Rating Size Rating 5” 200 psi@ 100°F.

6” 200 psi@ 100°F. 8” 150 psi @ 100°F.

Cv Factors*

Size Value 5" 300 6” 420 8” 900

Dimensions and weights

are for reference

only. Contact

Eaton for certified

drawings.

* For water with clean, perforated basket

Partial cutaway of Model 50 duplex strainer clearly illustrates all major parts—and gives a clear indication of the simplicity of design and ease of maintenance.

Dimensions (in/mm)

------------------ Weight (lb / kg)--------------- Pipe Carbon Stainless Size A B C D E F G H J K L Cast Iron Bronze Steel Steel

18.38 9.00 9.75 33.25 14.75 10.25 17.19 3/8 19.75 0.56 41.00 403 412 – – 5

467 229 248 845 375 260 437 – 502 14 1041 183 187 – – 22.00 12.88 12.50 36.25 19.50 11.75 20.75 3/8 19.75 0.63 42.00 500 583 580 615

6 559 327 318 921 495 298 527 - 502 16 1067 227 264 263 279

25.00 14.00 17.00 50.63 23.06 – 30.75 1/2 28.00 0.94 56.00 1500 1800 1610 1670 8

635 356 432 1286 586 – 781 – 711 24 56 682 818 732 759

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118 Fax: (248) 377-3172

[email protected] www.tfsi1.com

243

LIQUID PROCESS FILTRATION - STRAINERSModel 85 Y Strainer

1/4" to 10" Carbon Steel and Stainless Steel Threaded, Flanged, or Socket Weld

Connections

FEATURES Compact design Bolted or threaded covers Standard stainless steel screens Horizontal or vertical installation

Cross-section of a Y Strainer with blow off connection for quick and easy clean-out.

OPTIONS

Basket perforations from 1/32" to 1/2"

Basket mesh from 20 to 400 Monel screens

Eaton Model 85 Y strainers are engineered to withstand aggressive industrial and commercial applications. Y strainers protect downstream process system components by mechanically removing unwanted solids from liquid, gas, or steam lines by means of a perforated or wire mesh straining element. To protect against any bypass, the Model 85 Y strainers are manufactured with a precision-machined screen seat on the body of the strainer and high quality stainless steel screens fabricated to fit the strainer body perfectly. Model 85 Y strainers are available in

carbon steel or stainless steel for pipeline sizes from 1/4" to 10" with threaded, flanged, or socket weld connections. For cost-effective straining solutions, Y strainers work well in applications in which the amount of material to be removed from the flow is relatively small--resulting in long intervals between screen cleanings. The strainer screen is manually cleaned by shutting down the line and removing the strainer cap. For applications with heavier dirt loading, Y strainers fitted with a “blow off” connection permit cleaning of the screen without removing it from the strainer body.

Typical socket weld and threaded Y strainer

Eaton Model 85 y Strainers 1/4" to 10" Carbon and Stainless Steel-Threaded, Socket Weld & Flanged

Size Material End connection Cover Rating (WOG) non-shock

1/4" to 2" Carbon Steel Threaded or Socket Weld 600# Threaded 1480 psi @ 100°F 1/4" to 2" Stainless Steel Threaded or Socket Weld 600# Threaded 1440 psi @ 100°F 1/2" to 10" Carbon Steel Flanged 150# Bolted 285 psi @ 100°F 1/2" to 10" Carbon Steel Flanged 300# Bolted 740 psi @ 100°F 1/2" to 10" Stainless Steel Flanged 150# Bolted 275 psi @ 100°F 1/2" to 10" Stainless Steel Flanged 300# Bolted 720 psi @ 100°F

Socket Weld, Threaded Carbon Steel & Stainless Steel – 600# (in/mm)

Size A B C (Nom.) Cover Wt (lb / kg) 1/4 3.00 / 76 3.00 / 76 3/8 4.00 / 102 2 / 0.9 3/8 3.00 / 76 3.00 / 76 3/8 4.00 / 102 2 / 0.9 1/2 3.00 / 76 3.00 / 76 3/8 4.00 / 102 2 / 0.9 3/4 3.75 / 95 3.50 / 89 3/8 4.75 / 121 4 / 1.8 1 4.63 / 118 4.00 / 102 1/2 5.75 / 146 6 / 2.7

1-1/4 5.00 / 127 4.63 / 118 3/4 6.50 / 165 8 / 3.6 1-1/2 5.63 / 143 5.25 / 133 3/4 7.50 / 191 10 / 4.5

2 7.00 / 178 5.75 / 146 1 8.75 / 222 15 / 6.8 Consult Eaton for 12" and larger size dimensions. Dimensions and weights are for references only. Contact Eaton for certified drawings.

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118Fax: (248) 377-3172

[email protected] www.tfsi1.com

244

LIQUID PROCESS FILTRATION - STRAINERSModel 85 Y Strainer

Flanged Carbon Steel & Stainless Steel – 150# (in/mm) Typical Flanged Y Strainer Size A B C (Nom.) D Wt (lb / kg)

1/2 5.00 / 127 2.75 / 70 3/8 3.50 / 89 5 / 2.3 3/4 5.63 / 143 3.00 / 76 3/8 4.00 / 102 7 / 3.2 1 6.38 / 162 3.64 / 92 1/2 5.00 / 127 9 / 4.1

1-1/4 7.25 / 184 4.25 / 108 3/4 5.75 / 146 14 / 6.3 1-1/2 8.88 / 226 5.75 / 146 3/4 6.50 /165 18 / 8.2

2 7.88 / 200 6.00 / 152 1 8.25 / 210 16 / 7.3 2-1/2 9.75 / 248 6.50 / 165 1 9.25 / 235 25 / 11.4

3 10.00 / 254 7.25 / 184 1-1/4 10.50 / 267 35 / 16 4 12.13 / 308 9.75 / 248 1-1/2 14.75 / 375 70 / 32 6 18.50 / 470 14.25 / 362 2 21.00 / 533 130 / 59 8 21.63 / 549 18.00 / 457 2 26.75 / 679 240 / 109

10 26.00 / 660 22.50 / 565 2 33.75 / 857 300 / 136 Flanged Carbon Steel & Stainless Steel – 300# (in/mm)

Size

Size A B C (Nom.) D Wt (lb / kg)Steam Pressure Drops 1/2 5.25 / 133 2.75 / 70 3/8 3.50 / 89 6 / 2.7

3/4 6.00 / 152 3.00 / 76 3/8 4.00 /102 9 / 4.1

1 6.88 / 175 3.63 / 92 1/2 5.00 / 127 13 / 6.0

1-1/4 7.75 / 197 4.25 / 108 3/4 5.75 / 146 18 / 8.2

1-1/2 9.38 / 238 5.75 / 146 3/4 6.50 / 165 24 / 11

2 8.63 / 219 6.25 / 159 1 8.25 / 210 30 / 13.6

2-1/2 10.63 / 270 7.00 / 178 1 9.25 / 235 40 / 18.2

3 12.00 / 305 7.75 / 197 1-1/4 10.50 / 267 55 / 25

4 14.50 / 368 10.50 / 267 1-1/2 14.75 / 375 105 / 48

6 20.00 / 508 14.75 / 375 2 21.00 / 533 200 / 91

8 23.38 / 594 18.75 / 476 2 27.00 / 686 360 / 164

10 27.38 / 695 22.75 / 578 2 34.50 / 876 430 / 195

Flow Rates

Calculating Saturated Steam Pressure Drop Example: Pressure = 300 psig, Flow Rate = 20,000 lb/hr, Strainer Size = 4 inches

1. Locate steam flow on Scale A. 2. Follow vertical line to required

pressure. 3. Follow horizontal line to

strainer size. 4. Follow vertical line downward and read pressure drop on Scale C. 5. Pressure drop equals 1.25 psi.

Calculating Superheated Steam Pressure Drop

Example: Pressure = 300 psig, Flow Rate = 18,000 lb/hr, Strainer Size = 4 inches

1. Locate steam flow on Scale B.2. Follow horizontal line to superheat. 3. Follow vertical line to pressure. 4. Follow horizontal line to strainer size. 5. Follow vertical line and read Pressure drop on Scale C. 6. Pressure drop equals 1.25 psi.

Note: Use the superheat temperature value above the saturated steam temperature to obtain the point on this graph.

FLOW RATE (WATER) GPM

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118 Fax: (248) 377-3172

[email protected] www.tfsi1.com

245

LIQUID PROCESS FILTRATION - STRAINERSModel 90 Fabricated Simplex Strainer

1/4" to 10" Carbon Steel and Stainless Steel* Sizes 1" to 48" Flanged ANSI Class 150 or 300

FEATURES

Straight through flow design Low pressure loss Slant top basket design Basket perforations from 1/32" to 1" 20 to 400 mesh linings for fine

straining applications

OPTIONS

ANSI Class 600, 900, or 1500 flanges Hinged cover or davit assembly for

easier maintenance Alloy construction for body and

baskets RTJ-style connections Vent valves Drain valves Gauge taps Backflushing system for manual or

automated cleaning Pressure differential gauge and

switches Steam jacket for highly viscous fluids Rotated or offset nozzle placement High pressure capabilities ASME Code construction Brazilian NR-13 available European standards - DIN/PED

available Coatings and linings available upon

request * Stainless steel strainers include painted carbon steel, external, non-wetted fasteners as standard

Customize to Improve Performance and Meet Higher Pressure Requirements

Unique Strainer Basket A slant top design improves the flow through the strainer and results in significantly lower pressure drops. This design also results in a more compact basket that weighs less than an ordinary basket. This makes it possible for one person to remove it from the strainer housing, a labor saving feature when it comes time to clean or changeout the basket.

Common Modifications Rotated inlet and outlet nozzles to

eliminate an elbow in the downstream piping

Lowering let or the outlet nozzle, this eliminates serious alignment and support problems.

Cover Type Openings For applications with infrequent basket changing, Eaton offers a simple, cost-effective, bolted cover type. It’s available with a davit assembly cover for larger strainers withheavy covers, this makes it possible for a one-person operation.

For applications with more frequent changing, Eaton offers a hinged, quick opening cover secured by swing bolts.

This is adaptable for higher pressure applications. For medium size strainers, 8" to 16," a bolted slide hinge cover is available.

This permits one operator to engage the hinge and open the cover.

Backflush/Backwash option In systems with heavy, well-defined solids and sediment, this option backflushes the system without shutting the system down. A piping connection with an on/off backflush valve is fabricated at the strainer bottom and has a connection to the bottom of the strainer basket. When solids accumulate in the bottom of the basket, the backflush valve opens and the differential between the operating pressure and the backflush system removes the solids. The second step, backwashing, reverses the flow and removes residual dirt.

Optional Steam Jacketing Available in carbon steel or 316SS rated for service up to 450°F. This is ideal for the high temperatures required to process and transport heavy, viscous fluids without affecting the function or normal maintenance of the strainer. Steam jacketing maintains critical fluid temperature throughout the strainer. Design and fabrication to ASME section VIII and ANSI B31.1 codes are available.

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118Fax: (248) 377-3172

[email protected] www.tfsi1.com

246

LIQUID PROCESS FILTRATION - STRAINERSModel 90 Fabricated Simplex StrainerModel 90 with Quick Open Hinge Cover

Dimensions (in) Weight (lbs) Class Class Class

Nom 150 300 150/300 Class 150 Class 3000 Size A A B C D E F Cover Unit Cover Unit

2 14 14 12 8-5/8 6-5/8 1/2 26 6 71 6 90 3 15 15 12-1/2 8-5/8 6-5/8 1/2 26 6 73 6 105 4 16 16 14 9-1/2 8-5/8 1 21 9 122 9 158 5 16 17-1/2 15 11-1/4 10-3/4 1 22 9 128 9 176 6 20 21 17 11-1/4 10-3/4 1 24 12 168 12 236 8 22 23 21 13 12-3/4 1-1/2 28 15 226 15 278

10 32 33 25 15-3/4 16 1-1/2 33 30 360 30 483 12 35 36 28 17-3/4 18 1-1/2 39 37 535 37 734 14 37 38 33 19-3/4 20 2 45 46 804 46 1030 16 42 43 36 23-1/4 24 2 49 68 1188 68 1437 18 42 43 39 23-1/4 24 2 53 68 1255 68 1553 20 43 44-1/2 44 27-3/4 30 2 59 71 1322 71 1656 24 48 49-3/4 60 27-3/4 30 2 78 88 1860 88 2344

Model 90 with Bolted Cover Dimensions (in) Weight (lbs) Class Class Class Class

Nom 150 300 150 300 Class 150 Class 300 Size A A B C C D E F Cover Unit Cover Unit

2 14 14 12 7 9 6-5/8 1/2 23 28 110 50 160 3 15 15 12 1/2 8 9 6-5/8 1/2 24 28 120 50 175 4 16 16 14 8-1/4 9 1/2 8-5/8 1 21 45 147 81 219 5 16 17-1/2 15 9-1/2 11 10-3/4 1 22 45 153 81 237 6 20 21 17 9-1/2 11 10-3/4 1 24 70 203 127 328 8 22 23 21 11 12-1/2 12-3/4 1-1/2 28 110 281 184 407

10 32 33 25 13 14-1/2 16 1-1/2 33 170 450 307 710 12 35 36 28 14-1/2 16 18 1-1/2 39 209 644 390 1024 14 37 38 33 15-3/4 17-1/2 20 2 45 272 951 492 1397 16 42 43 36 18-1/4 20 24 2 49 411 1409 754 2011 18 42 43 39 18-1/4 20 24 2 53 411 1486 754 2127 20 43 44-1/2 44 21-3/4 24 30 2 59 411 1553 754 2231 24 48 49-3/4 60 21-3/4 24 30 2 78 681 2291 1403 3497

Model 90 strainer with offset nozzles, quick open cover, and flanged drain

Model 90 with Bolted Cover

Model 90 with Quick Open Hinge Cover

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118 Fax: (248) 377-3172

[email protected] www.tfsi1.com

247

LIQUID PROCESS FILTRATION - SEPARATORSLakos Industrial Separator SystemEffective, Comprehensive Separation Solutions

You can remove solids from liquids with a variety of products. You know the drawbacks of traditional filtration. You have the opportunity to make a much better choice.

LAKOS Separators employ centrifugal action to remove troublesome solids from liquids. To extend the effective life of process liquids. To protect process equipment from abrasive wear and fouling. To control or eliminate waste liquid/solids. To reduce downtime and maintenance. To keep your fluid systems operating at optimum efficiency.

What Makes LAKOS Different Is What Makes LAKOS Better Not just solids removal, but also the concentration and transfer of separated solids (with little or no liquid loss) to your choice of solids-handling device. Reduced liquid waste. Reduced solids waste handling...and costs. Reduced space, processing and maintenance. Proven payback value. Effective solids removal performance is engineered into every model series. Matched with your choice of purging and solids-handling systems, LAKOS assembles specific solutions for your specific problems. Complete systems. Engineered compatibility. Simplified, one-source purchasing. Easy installation. Reliable start-up and operation. Dependability you can trust. LAKOS has been providing innovative and adaptable solutions for over twenty-five years throughout the world. Experienced and systems-oriented, LAKOS welcomes your application challenges. How It Works

No moving parts to wear out No screens, cartridges, cones or filter elements to

clean or replace No backwashing No routine maintenance or downtime requirements No standby equipment needs Low and steady pressure loss Easily automated Compact, space-saving profiles Little or no liquid loss Effective solids concentration for easy

disposal/recovery LAKOS By Comparison Use this simple criteria to effectively compare LAKOS Separators to any other filtration/separation technology:Particle size removal Pressure loss LAKOS Separators operate at a steady low of only 3 12 psi (0.2-0.8 bar). Liquid loss and solids handling Replacement parts LAKOS requires no replacement parts. Maintenance requirements Easily automated; no system shutdowns. Space requirements Lowest space requirements of any filtration/separation technology.

Vortube

Solids Purge

Outlet

Pressure gauges with petcock valves (included as standard) to monitor proper flow range

Rigid coupling for internal access; optional flange assembly available

Internal Swirlex tangential slots accelerate flow to maximize separation of solids with reduced pressure loss

Particles are separated from fluid via centrifugal action

Free of separable particles, fluid spirals up the vortex to the outlet Vortex flow draws fluid and pressure from the solids collection chamber via the Vortube

Manual IsolationValve (included

with Auto Purge System) provides

for removal of Auto Purge valve

for servicing

Grooved-end connections

at inlet & outlet for fast, secure, easy

installation. Optional ANSI,

DIN or JIS flanges also available

Fluid and pressuredrawn by Vortube to more positively

allow even finer solids to be drawn

into solids collection chamber

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118Fax: (248) 377-3172

[email protected] www.tfsi1.com

248

LIQUID PROCESS FILTRATION - SEPARATORSLakos Industrial Separator System

Protect Your Fluid System Applications With The Performance of LAKOS The potential for LAKOS Separators exists in virtually all fluid flow systems, particularly in the applications noted. Put our experience to work solving your toughest problems. Compare your operating costs to the payback value LAKOS offers in these areas. Call us for immediate and specific application assistance.

Typical Applications

Spray nozzle and small orifice protection Avoid fouling, clogging and/or abrasive wear. Eliminate excessive downtime, maintenance and/or parts replacements. Extend the life of finer filtration and water

treatment systems Reduce fine-micron cartridge or bag filter consumption with the pre-removal of larger solids (see performance at right). Extend the operating cycles of filter elements and water treatment processes. Reduce maintenance, downtime and filter media replacement costs. Heat exchanger protection Control solids fouling. Remove precipitated

grit and scale. Maintain optimum system efficiencies and avoid excessive energy loss.

Prevent excessive solids accumulation in

pits, sumps and tanks Cooling tower basins. Quench pits. Parts washing tanks. Eliminate solids build-up and the inevitable shutdowns, shoveling and maintenance routines. Avoid solids-induced bacteria growth and premature liquid disposal. Waste minimization Extend the life of process liquids by removing troublesome solids. Concentrate separated solids for easy disposal or recovery/re-use. Reduce your EPA- regulated waste status for significant process-related savings.

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118 Fax: (248) 377-3172

[email protected] www.tfsi1.com

249

LIQUID PROCESS FILTRATION - SEPARATORSLakos Industrial Separator System

LAKOS: Successfully applied in all industries:

Automotive Pre-wash and pre-paint stations, deluge processes, coolant filtration. Food Processing Bulk pre-washing, process liquid recycling, fry oil reclamation. Primary Metals Quench systems, spray nozzles and descaling operations, hot strip mills, rolling mills, scrap recovery. Process Cooling Heat exchanger protection, compressor jackets, pump seals, open and closed loop recirculation, heat pumps. Chemical Processing Liquid recycling, pre-filtration, waste minimization. Municipal Services Source water sand and grit removal, wastewater pre-treatment, water conditioning systems. Metalworking Fluids Coolant recycling, parts washing, wire processing, pit/sump scavenging, scrap recovery. Vehicle Wash Systems Cars, busses, trucks, trains. Pit/sump scavenging, wash water re-use without detergent/chemical stripping. Mining Operations Recycling, solids recovery, Pulp and Paper Mills Plant intake water, black liquor, process recycling. HVAC Comfort Cooling Systems Spray nozzle protection, basin scavenging, bacteria control through reduced solids accumulation, heat exchangers, reduced blowdown and chemical usage, energy savings. Fuel Distribution Systems Jet fuel, kerosene, gasoline, pipeline, pre-filtration. Oil and Gas Pump protection, primary and secondary produced water, brine filtration, frac water, disposal wells, secondary recovery, offshore platforms. Also – Power plants, industrial laundries, glass and plastics, fire protection systems, wet scrubbers, pump intake screening, water well pump protection and more.

Performance

Particle size vs. particle weight Centrifugal separation employs the principles of velocity and gravity to achieve performance. Essentially, heavier particles (indicated by higher specific gravity ratings, see chart at right) can be removed more easily and at predictably smaller particle sizes (see graph below).

Improved performance when recirculating liquids The continuous recirculation of a given liquid through a LAKOS Separator will predictably and noticeably remove an increasingly greater percentage of even finer solids (see graph below). Field and laboratory proven, this attribute can also be enhanced with two stage “super separators” and is especially valuable where liquids and chemicals are expensive or where solids-contaminated liquid disposal is costly or regulated.

Fibrous solids and larger particles Anticipating the need to remove large and fibrous solids as well as (or even instead of) very fine solids clearly reinforces the versatility and value of LAKOS Separators. Limited only by the clearance of the separator’s internal tangential slots or annular transfer ring, LAKOS Separators can remove solids from as large as 1/4 inch (6 mm) up to 2 inches (51 mm). Consult your LAKOS representative for specific details.

Typically Separable Materials Specific Gravity Aluminum 2.7 Ashes (Coal) 2.0 Brass 9.0 Bronze; Copper 8.9 Carbon; Concrete; Lava 1.8-2.5 Coal (Anthracite) 1.3-1.9 Earth (Silt; Soil) 1.2-2.0 Glass (Crystal) 3.0 Granite; Gravel 2.5-3.0 Graphite 2.3 Iron 7.8 Lead 11.3 Limestone 2.8 Manganese 7.4 Nickel 8.9 Sand; Silica; Shale 2.6-2.8 Steel 7.8 Tin Ore 6.4-7.0

Solids Removal Chart

Corporate Office: 2725 Commerce Parkway

Auburn Hills, MI 48326

Toll Free: (800) 331-3118Fax: (248) 377-3172

[email protected] www.tfsi1.com

250