list of technical standard for water supply

1

EQUIPMENT, DEVICES, MATERIAL, SYSTEM OR FACILITY FOR WATER SUPPLY SYSTEM (list as of November 2010)

No. Category Items

1 A. Treatment of water A.1 Water Treatment Chemical - Coagulant and flocculant - Adsorption agents - Fluoridation chemical - Disinfectant - Conditioning agent - Other oxidation agent

A.2 Single treatment unit

- membrane filter

A.3 Complete small scale water treatment

2 B. Conveyance/distribution of Water

B.1 Pipes with material:

- Polyethylene (PE) - Polyvinylchloride (PVC) - Acrylonitrile-butadiene-styrene

(ABS)

- Polypropylene (PP) - Polybutelene (PB) - Glass reinforced plastic (GRP) - Mild Steel Cement Lined (MS) - Stainless Steel (SS) - Ductile Iron (DI) - Copper tubes - Composite pipes

B.2 Paip Fitting/ Joint/ Special

Joints

- Flanged joins - Welded joints - Gobout joints - Flexible mechanical coupling - Butt Fusion/electrifusion - Sleeve coupling - Push on spigot and socket - Sinle gland-machanical joint - Stepped coupling Fittings and Special

- Tapers - Flange adaptors - Bends - Tees - Angle branches and Crosses - Puddle Flanges - Bellmouth - Rose strainer - Blank Flanges

2

No. Category Items

3. C. Storage of water (tank and

reservoir

C.1 Balancing and services reservoir

- Reinforce concrete - Prestress concrete - Precast concrete - Glass Reinfirced Polyester - Fiberglass RP - Stainless steel - Polyethelene - Galvanized pressed steel

3 D. Other mechanical equipment and installation

for water supply system

D.1 Pump

D.2 Valve

- Sluice valves/gate valves - Check valves - Scour valves - Air valves/ air release valve - Stoppable valves/ lockable

valves/servicing valves

- Control valve/automatic control valve

- Butterfly valves - Reflux valves - Ball or Float valves - Altitude valves - Pressure reducing valves - Pressure sustaining valves - Constant flow valves - Hydrants - Free Discharge Valve

- In-Line Throttling Valve

- Submerged Discharge Valve

- Pressure Sustaining Valve

- Constant Flow Valve

- Backflow Preventer

D.3 Meter

- Bulk meters - Sub meters - Domestic meter

D.4 Others

(1) Air blower (2) Air compressors (3) Chemical dosing devices (4) Surge suppression devices (5) Instrumentation (6) Hydraulic controlled equipment (7) Bandscreen

3

No. Category Items

(8) Ejector

4. E. Water supply plumbing

system

(1) Taps (2) Stop valves (3) Ball valves (4) Constant flow valves (5) Flushing cisterns (6) Bidets (7) Drinking fountain

1

LIST OF TECHNICAL STANDARD FOR EQUIPMENT, DEVICE, MATERIAL, SYSTEM OR FACILITY FOR WATER SUPPLY SYSTEM

CATEGORY A: TREATMENT OF WATER

A.1 WATER TREATMENT CHEMICAL A.2 SINGLE TREATMENT UNIT A.3 COMPLETE SMALL SCALE WATER TREATMENT

PRODUCTS STANDARDS

Aluminium Sulphate (Kibble & Liquid Form)

MS 699:2008: Aluminium Sulphate for Use in Potable Water Supply Specification (Second Revision)

Polyaluminium chloride hydroxide / Polyaluminium chloride hydroxide sulphate / Polyaluminium chloride hydroxide silicate sulphate

MS 1454:2007 Liquid polyaluminium chloride for use in potable water supply specification (first revision), 2007

Sodium Aluminate

MS 1572:2003 Specification for Sodium Aluminate used for potable water supply

Iron (III) chloride Iron (III) chloride sulphate

MS 1450:1999: Specification for liquid ferric chloride for potable water treatment

Iron (II) sulphate Iron (III) sulphate liquid Iron (III) sulphate solid

MS 1452 1999 Specification for liquid ferric sulphate for potable water treatment

MS 1456:1999 : Guidelines for the application of liquid ferric based salts in potable water

2

PRODUCTS STANDARDS

Application of liquid ferric based product in potable water treatment

treatment

Product based on Polydiallyldimethyl ammonium chloride (PolyDADMAC) - Anionic, Cationic

MS 1930:2007 : Poly(polydiallyldimethyl ammonium chloride) or polyDADMAC for use in potable water supply

Product based on polyacrylamides - Anionic, Cationic and non-ionic

MS 1928:2007 : polyacrylamides for use in potable water supply (specification)

Product based on Polyamines - Anionic, Cationic

MS 1929: 2007 : polyamines for use in potable water supply (specification)

Calcium carbonate MS 1836:2005 Hydrated Lime and slurry lime for use in potable water supply

Sodium carbonate MS 1551 : 2002 Specification for soda ash (sodium carbonate) used for potable water supply

Chlorine MS 171:2003 Specification for liquid chlorine used for potable water supply Sodium hypochlorite MS 1718:2003 : sodium hypochlorite for use in potable water supply

Calcium hypochlorite MS 1548:2003 : specification for calcium hypochlorite use for potable water supply 2003

Sodium flouride MS 1573 : 2003 Specification for sodium fluoride used for potable water supply

Sodium silicofloride MS 1724:2004 Sodium silicofloride for use in potable water supply specification 2004

potassium permanganate

MS 1576: 2003 specification for potassium permanganate used for potable water supply

Copper sulphate MS 1576:2003: Specification for Copper Sulphate used for potable water.

Activated carbon (powder) MS 873:2005 : powdered activated carbon for use in potable water supply specification

Activated carbon (granular) Granular activated carbon for use in potable water supply (specification)

3

PRODUCTS STANDARDS

Silica sand MS 847: 1983 - specification for silica sand for the manufacturer of sodium silicate.

Sodium Hydroxide

MS 700: 1981 (Specification) for sodium hydroxide (technical grades)

CATEGORY B: CONVEYANCE OF WATER

B.1 PIPE B.2 PIPE FITTINGS/JOINT/SPECIAL

No. Product Standards referred by industry Standard for

SPAN registration Remarks

Standard No. Standard Title

CATEGORY B PRODUCTS USED FOR THE CONVEYANCE OF WATER.

B.1 Pipes

B.1.1 Polyethylene (PE) Pipes

B.1.1.1 Polyethylene (PE)

Pipes

MS 1058: Part 2: 2002

Specification for Polyethylene (PE) Piping Systems for Water Supply : Part 2 : Pipes (Third

Revision) MS 1058: Part 2:

2005

MS 1058: Part 2: 2005

Specification for Polyethylene (PE) Piping Systems for Water Supply : Part 2 : Pipes (Forth

Revision)

4




ISO 4427-2: 2007

Plastics Piping Systems Polyethylene (PE) Pipes and

Fittings for Water Supply Part 2: Pipes

B.1.1.2 PE-RT Pipes

ISO 22391: Part 2: 2007

Plastics Piping Systems for Hot and Cold Water Installations

Polyethylene of Raised Temperature Resistance (PE-

RT) : Part 2 : Pipes ISO 22391: Part 2: 2007

MS ISO 10508:2004

Plastics Piping Systems for Hot and Cold Water Installations Guidance for Classification and

Design

B.1.2 Polyvinyl Chloride (PVC) Pipes

B.1.2.1 Unplasticized

Polyvinylchloride (uPVC) Pipes

MS 628: Part 1: 1999 AMD.1: 2001 & AMD.2: 2002

Specification for Unplasticised PVC (uPVC) Pipes for Water

Supply : Part 1: Pipes (1st revision)

MS 628: Part 1: 1999 AMD.1: 2001

& AMD.2: 2002

MS 762: 2007, AMD.1: 2010

Plastics Piping Systems for Industrial Applications

Unplasticised Polyvinyl Chloride (PVC-U) Specifications for Components and the System

(First Revision)

5




BS 3505: 1986

Specification for Unplasticized Polyvinyl Chloride (PVC-U)

Pressure Pipes for Cold Potable Water.

BS 3506: 1969 Specification for Unplasticized PVC Pipes for Industrial Uses

BS EN ISO 1452-2: 2009

Plastics Piping Systems for Water Supply and for Buried and

Above-Ground Drainage and Sewerage Under Pressure.

Unplasticized Poly(vinyl Chloride) (PVC U). Pipes

B.1.2.2 Multi-Layer uPVC

Pipes

MS 628: Part 1: 1999 AMD.1: 2001 & AMD.2: 2002

Specification for Unplasticised PVC (uPVC) Pipes for Water

Supply : Part 1: Pipes (1st revision)

MS 628: Part 1: 1999 AMD.1: 2001

& AMD.2: 2002

B.1.2.3 Chlorinated

Polyvinylchloride (cPVC) Pipes

ASTM D2846 / D2846M 09b

Standard Specification for Chlorinated Polyvinyl Chloride (cPVC) Plastic Hot and Cold Water Distribution System.

ASTM D2846 / D2846M 09b

B.1.3 Acrylonitrile-Butadiene-Styrene (ABS) Pipes

6




B.1.3.1 Acrylonitrile-Butadiene-

Styrene (ABS) Pipes

MS 1419: Part 1: 2007

Acrylonitrile-Butadiene Styrene (ABS) Piping Systems for

Pressure Applications Part 1: Specification for Compounds,

Pipes and Fittings (First Revision) MS 1419: Part 1:

2007 &

MS 1419: Part 2: 2007

MS 1419: Part 2:

2007


Pressure Applications Part 2: Methods of Test

AS/NZS 3518: 2004 Acrylonitrile Butadiene Styrene (ABS) Compounds, Pipes and

Fittings for Pressure Application

B.1.4 Polypropylene (PP) Pipes

B.1.4.1 Polypropylene Random

(PP-R) Pipes

ISO 15874: Part 2: 2003


Polypropylene (PP). Part 2: Pipes ISO 15874: Part 2:

2003

DIN 8077: 2008 Polypropylene (PP) Pipes PP-

H, PP-B, PP-R, PP-RCT - Dimensions

B.1.4.2 Polypropylene Blend

(PP-B) Pipes ISO 15874: Part 2:

2003


Polypropylene (PP). Part 2: Pipes

ISO 15874: Part 2: 2003

7




DIN 8077: 2008 Polypropylene (PP) Pipes PP-

H, PP-B, PP-R, PP-RCT - Dimensions

B.1.5 Polybutylene (PB) Pipes

B.1.5.1 Polybutylene (PB)

Pipes AS/NZS 2642-2:

1994

Polybutylene (PB) Plumbing Pipe Systems Polybutylene (PB) Pipe for Hot and Cold

Water Applications.

AS/NZS 2642-2: 1994

B.1.6 Glass Reinforced Plastic (GRP) Pipes

B.1.6.1 Glass Reinforced

Plastic (GRP) Pipes ISO 10639: 2004

Plastics Piping System for Pressure and Non-pressure

Water Supply Glass Reinforced Thermosetting

Plastics (GRP) Systems Based On Unsaturated Polyester (UP)

Resin

ISO 10639: 2004

B.1.7 Mild Steel Cement Lined (MS) Pipes

B.1.7.1 Mild Steel Cement Lined (MS) Pipes

BS 534: 1990 Steel Pipes, Joints and Specials

for Water and Sewage BS 534: 1990

8




ERW & SAW

BS 3601: 1987

Carbon Steel Pipes and Tubes with Specified Room

Temperature Properties for Pressure Purposes

B.1.7.2 Mild Steel Pipes (Bare tubes) ERW & SAW

MS 1968: 2007 (BS EN 10224: 2002)

Non-alloy steel tubes and fittings for the conveyance of aqueous

liquids including water for human consumption Technical

delivery conditions. MS 1968: 2007 (BS EN 10224:

2002)

BS 3601: 1987

Carbon Steel Pipes and Tubes with Specified Room

Temperature Properties for Pressure Purposes

B.1.8 Stainless Steel (SS) Pipes

B.1.8.1 Stainless Steel (SS)

Pipes - Industrial MS 1841: 2010 (ASTM A 312)

Seamless, Welded and Heavily Cold Austenitic Stainless Steel

Pipes - Specification

MS 1841: 2010 (ASTM A 312)

B.1.8.2 Stainless Steel (SS) Light Gauge Tubes -

MS 1988: 2007 (BS EN 10312)

Welded Stainless Steel Tubes for the Conveyance of Water and Other Aqueous Liquids Technical Delivery Conditions

JIS G 3448: 2004 Light Gauge Stainless Steel

Pipes for Ordinary Piping

B.1.9 Ductile Iron (DI) Pipes

9




B.1.9.1 Ductile Iron (DI) Pipes

BS EN 545: 2006

Ductile Iron Pipes, Fittings, Accessories and Their Joints for Water Pipelines Requirement

and Test Method MS 1919: 2006 (BS EN 545: 2002)

MS 1919: 2006 (BS EN 545: 2002)


and Test Method

B.1.10 Copper Tubes

B.1.10.1 Copper Tubes BS EN 1057: 1996

Copper and Copper Alloys. Seamless, Round Copper

Tubes for Water and Gas in Sanitary and Heating

Applications

BS EN 1057: 1996

B.1.11 Composite Pipes

B.1.11.1 PE Aluminium Pipes ASTM F1282 - 03

Standard Specification for Polyethylene / Aluminium / Polyethylene (PE-AL-PE)

Composite Pressure Pipes

ASTM F1282 - 03

B.1.11.2 Polysteel Pipes CJ/T 136: 2001 Steel Pipes of Lining Plastic for

Water Supply CJ/T 136: 2001

This standard is in Chinese Language. There is no

english version available.

10




B.2 Pipe Fittings

B.2.1 Polyethylene (PE) Fittings

B.2.1.1

Polyethylene (PE) Fittings

BS EN 12201-3:2003 Polyethylene Pipes for Water

Supply. Part 3 : Fittings

MS 1058: Part 3: 2006

AS/NZS 4129: 2008 Fittings for Polyethylene (PE) Pipes for Pressure Application

MS 1058: Part 3: 2006

Polyethylene (PE) Piping Systems for Water Supply Part

3 : Fittings

ISO 4427-3: 2007

Plastics Piping Systems Polyethylene (PE) Pipes and

Fittings for Water Supply Part 3: Fittings

B.2.1.2

HDPE Joints Assemblies and

Fittings for HDPE Pipes

DIN 16963: Part 4: 1988

Pipe Joint Assemblies and Fittings for High-Density

Polyethylene (PE-HD) Pressure Pipes; Adaptors for Fusion

Jointing, Flanges and Sealing Elements; Dimensions

DIN 16963: Part 4: 1988,

DIN 16963: Part 5: 1989 &

DIN 16963: Part 6: 1989

11




DIN 16963: Part 5: 1989

Pipe Joints and Components of Polyethylene (PE) for Pipes

Under Pressure, PE 80 and PE 100 Part 5: General Quality

Requirements, Testing

DIN 16963: Part 6: 1989

Pipe Joints Assemblies and Fittings for High-Density

Polyethylene (PE-HD) Pressure Pipes; Injection-Moulded Fittings

for Butt Welding: Dimensions

B.2.1.3

PE Socket Fusion Fittings

DIN 16963: Part 5: 1989



Requirements, Testing DIN 16963: Part 5: 1989,

DIN 16963: Part 8: 1980,

DIN 16963: Part 9: 1980,

DIN 16963: Part 10: 1980 &

DIN 16963: Part 14: 1983

DIN 16963: Part 8:

1980

Pipe Joints and Elements for High Density Polyethylene

(HDPE) Pressure Pipelines, Types 1 and 2; Injection

Moulded Elbows for Socket-Welding, Dimensions

DIN 16963: Part 9: 1980



Moulded Tee Pieces for Socket-Welding, Dimensions

12




DIN 16963: Part 10: 1980



Moulded Sockets and Caps for Socket-Welding, Dimensions

DIN 16963: Part 14: 1983

Pipe Joint Assemblies and Fittings for High-Density

Polyethylene (HDPE) Pressure Pipes; Pipe Couplings;

Dimensions

B.2.1.4

PE Fabricated Fittings

DIN 16963: Part 1: 1980


(HDPE) Pressure Pipelines, Types 1 and 2; Pipe Bends of

Segmental Construction for Butt-Welding, Dimensions

DIN 16963: Part 1: 1980,

DIN 16963: Part 2: 1983 &

DIN 16963: Part 5: 1999

DIN 16963: Part 2: 1983

Pipe Joint Assemblies and Fittings for Types 1 and 2 High Density Polyethylene (HDPE)

Pressure Pipes; Tees and Branches Produced by Segment

Inserts and Necking for Butt Welding; Dimensions

13




DIN 16963: Part 5: 1999




B.2.1.5

Nylon Joints and Compression Fittings for Use with HDPE

Pipes

BS 5114: 1975 (1981) Amd.2 - 1987

Specification for Performance Requirements for Joints and Compression Fittings for Use

with Polyethylene Pipes BS 5114: 1975 (1981) Amd.2 -

1987

MS ISO 10508: 2009


Design

B.2.2 Unplasticized Polyvinyl Chloride (PVC) Fittings

B.2.2.1

Unplasticized Polyvinylchloride (uPVC) Fittings

MS 628: Part 2: Section 2.1: 1999

Specification for Unplasticised PVC (uPVC) Pipes for Water Supply : Part 2: Joints and Fittings for Use with uPVC

Pipes: Section 2.1: uPVC Joints and Fittings

MS 628: Part 2: Section 2.1: 1999

14




BS EN ISO: 1452-3: 2009



Unplasticized Poly(vinyl Chloride) (PVC U). Fittings.

BS 4346-1: 1969

Joints and Fittings for use with Unplasticized PVC Pressure

Pipes. Injection Moulded Unplasticized PVC Fittings for Solvent Welding for use with

Pressure Pipes, Including Potable Water Supply.

BS 4346-2: 1970

Joints and Fittings for use with Unplastisized PVC Pressure

Pipes. Mechanical Joints and Fittings, Principally of Unplasticized PVC.

B.2.2.2

Chlorinated

Polyvinylchloride (cPVC) Fittings

ASTM D2846 / D2846M 09b


ASTM D2846 / D2846M 09b

15




B.2.3 Acrylonitrile-Butadiene-Styrene (ABS) Fittings

B.2.3.1

Acrylonitrile-Butadiene-Styrene (ABS) Fittings

MS 1419: Part 2: 1997



MS 1419: Part 2: 1997 &

MS 1419: Part 1: 2007

MS 1419: Part 1: 2007



Pipes and Fittings (First Revision)



B.2.4 Polypropylene (PP) Fittings

B.2.4.1

Polypropylene (PP-R, PP-B & PP-H) Fittings

ISO 15874: Part 3: 2003

Plastics Piping Systems for Hot and Cold Water Installations Polypropylene (PP) Part 3 :

Fittings

ISO 15874: Part 3: 2003

16




DIN 16962-5: 2000

Pipe Joints and Elements for Polypropylene (PP) for Pipes

Under Pressure, PP-H 100, PP-B 80 and PP-R 80 Part 5:

General Quality Requirements, Testing.

B.2.4.2

Polypropylene (PP) Compression Fittings

for HDPE Pipes

BS 5114: 1975 (1981) Amd.2 - 1987


with Polyethylene Pipes

BS 5114: 1975 (1981) Amd.2 -

1987

ISO 3458: 1976

Assembled Joints Between Fittings and Polyethylene (PE)

Pressure Pipes Test of Leakproofness Under Internal

Pressure.

ISO 3459: 1976

Polyethylene (PE) Pressure Pipes Joints Assembled with

Mechanical Fittings Internal Under-Pressure Test Method

and Requirement.

ISO 3503: 1976


Pressure Pipes Test of Leakproofness Under Internal Pressure when Subjected to

Bending.

17




ISO 3501: 1976


Pressure Pipes Test of Resistance to Pull Out.

ISO 14236: 2000

Plastics Pipes and Fittings Mechanical-Joint Compression

Fittings for Use with Polyethylene Pressure Pipes in

Water Supply Systems.

B.2.5 Glass Reinforced Plastic (GRP) Fittings

B.2.5.1

Glass Reinforced Plastic (GRP) Fittings

ISO 10639: 2004




Resin

ISO 10639: 2004

B.2.6 Mild Steel (MS) Cement Lined Fittings

B.2.6.1

Mild Steel (MS) Cement Lined

Specials (ERW & SAW)


for Water and Sewage

BS 534: 1990

MS 1968: 2007



delivery conditions.

18




B.2.7 Stainless Steel (SS) Fittings

B.2.7.1

Stainless Steel (SS) Threaded Fittings

ISO 4144: 2003 Pipework Stainless Steel

Fittings Threaded in Accordance with ISO 7-1.

ISO 4144: 2003

B.2.7.2

Stainless Steel (SS) Welded Fittings

MS 1842: 2010 (ASTM A 403)

Wrought Austenitic Stainless Steel Piping Fittings

Specification (First Revision).

MS 1842: 2010 (ASTM A 403)

B.2.7.3

Stainless Steel (SS) Press Fittings

SAS 322: 2003 Stainless Steel Press Fittings SAS 322: 2003

This standard is in Japanese Language.

There is no english version available.

B.2.8 Ductile Iron (DI) Fittings

B.2.15 Ductile Iron (DI)

Fittings MS 1919: 2006

(BS EN 545: 2002)


and Test Method

MS 1919: 2006 (BS EN 545: 2002)

B.2.9 Copper Fittings

B.2.9.1

Copper Fittings (Short Ends & Capillary)

BS EN 1254-1: 1998

Copper and Copper Alloys. Plumbing Fittings. Fittings with Short Ends for Capillary Brazing

to Copper Tubes.

BS EN 1254-1: 1998

B.2.9.2

Copper Fittings (Compression Ends)

BS EN 1254-2: 1998

Copper and Copper Alloys. Plumbing Fittings. Fittings with Compression Ends for Use with

Copper Tubes.

BS EN 1254-2: 1998

19




B.2.9.3

Copper Fittings (Combining End)

BS EN 1254-4: 1998

Copper and Copper Alloys. Plumbing Fittings. Fittings

Combining Other End Connections with Capillary or

Compression Ends.

BS EN 1254-4: 1998

B.2.10 Composite Fittings

B.2.10.1 Polysteel Fittings CJ/T 137: 2001 Malleable Iron Threaded Fittings

of Lining Plastic for Water Supply.

CJ/T 137: 2001 This standard is in Chinese

Language. There is no english version available.

B.2.10.2 Polyphenol Oxidase

(PPO) Fittings AS 4176: 1994

Polyethylene / Aluminium and Cross-linked Polyethylene /

Aluminium Macro-Composite Pipe Systems for Pressure

Applications.

AS 4176: 1994

This is only the nearest standard available.

Standard specific for this product is not available.

B.2.11 Adapter

B.2.11.1 Variable Adapter Spesifikasi JKR 20200-0045-99

JKR Standard Specification for Detachable Joints and Variable Adaptors for uPVC, Ductile Iron

and AC Pipes.

Spesifikasi JKR 20200-0045-99

B.2.11.2 Flange Adapter Spesifikasi JKR 20200-0048-99

JKR Standard Specification For Flexible Couplings and Flange

Adaptors.


20




B.2.11.3 Flexible Coupling Spesifikasi JKR 20200-0048-99


Adaptors.


B.2.11.4 Detachable Joint Spesifikasi JKR 20200-0045-99


and AC Pipes.


B.2.12 Saddle

B.2.12.1 Ferrous Saddle Spesifikasi JKR 20200-0044-99

JKR Standard Specification for Ferrous Saddles.


B.2.12.2 2 in 1 Adjustable

Saddle

Spesifikasi JKR 20200-0044-99 CL.

17.10



CL. 17.10

B.2.12.3 PP Clamp Saddle JKR No. 1 95 (BA)

JKR Standard Specification for Polypropylene (PP) Clamp

Saddle to be Used with Polyethylene (PE) Pipes.

JKR No. 1 95 (BA)

B.2.13 Pillar Hydrant

B.2.13.1 Pillar Hydrant Spesifikasi JKR 20200-0042-99

JKR Standard Specification for Ductile Iron Pillar Hydrants.


21




MS 1395: 1996 Specification for Pillar Hydrants MS 1395: 1996

This MS Adopted the JKR No. 1 93 (BA) JKR Specification for Pillar

Hydrants.

B.2.14 Strainer

B.2.14.1 Ductile Iron (DI)

Strainer Spesifikasi JKR 20200-0100-01

JKR Standard Specification for Ductile Iron Strainer (DN 50 to

DN 600)


B.2.15 Ferrules

B.2.15.1 Swivel Ferrules Spesifikasi JKR 20200-0174-04

JKR Standard Specification for Ferrules

B.2.15.2 Under Pressure Vertical Ferrules

MS 1396: 2006 Ferrules Specification (First

Revision)

B.2.1.4 PE Fabricated Fittings DIN 16963: Part 1:

1980


(HDPE) Pressure Pipelines, Types 1 and 2; Pipe Bends of

Segmental Construction for Butt-Welding, Dimensions

DIN 16963: Part 1: 1980,

DIN 16963: Part 2: 1983 &

DIN 16963: Part 5: 1999

22




DIN 16963: Part 2: 1983

Pipe Joint Assemblies and Fittings for Types 1 and 2 High Density Polyethylene (HDPE)

Pressure Pipes; Tees and Branches Produced by Segment

Inserts and Necking for Butt Welding; Dimensions

DIN 16963: Part 5: 1999




B.2.1.5

Nylon Joints and Compression Fittings for Use with HDPE

Pipes

BS 5114: 1975 (1981) Amd.2 - 1987



BS 5114: 1975 (1981) Amd.2 -

1987

MS ISO 10508: 2009


Design

23




B.2.2 Unplasticized Polyvinyl Chloride (PVC) Fittings

B.2.2.1

Unplasticized Polyvinylchloride (uPVC) Fittings

MS 628: Part 2: Section 2.1: 1999

Specification for Unplasticised PVC (uPVC) Pipes for Water Supply : Part 2: Joints and Fittings for Use with uPVC

Pipes: Section 2.1: uPVC Joints and Fittings

MS 628: Part 2: Section 2.1: 1999

BS EN ISO: 1452-3: 2009



Unplasticized Poly(vinyl Chloride) (PVC U). Fittings.

BS 4346-1: 1969

Joints and Fittings for use with Unplasticized PVC Pressure

Pipes. Injection Moulded Unplasticized PVC Fittings for Solvent Welding for use with

Pressure Pipes, Including Potable Water Supply.

BS 4346-2: 1970

Joints and Fittings for use with Unplastisized PVC Pressure

Pipes. Mechanical Joints and Fittings, Principally of Unplasticized PVC.

24




B.2.2.2

Chlorinated Polyvinylchloride (cPVC) Fittings

ASTM D2846 / D2846M 09b


ASTM D2846 / D2846M 09b

B.2.3 Acrylonitrile-Butadiene-Styrene (ABS) Fittings

B.2.3.1

Acrylonitrile-Butadiene-Styrene (ABS) Fittings

MS 1419: Part 2: 1997



MS 1419: Part 2: 1997 &

MS 1419: Part 1: 2007

MS 1419: Part 1: 2007



Pipes and Fittings (First Revision)



B.2.4 Polypropylene (PP) Fittings

B.2.4.1

Polypropylene (PP-R, PP-B & PP-H) Fittings

ISO 15874: Part 3: 2003

Plastics Piping Systems for Hot and Cold Water Installations Polypropylene (PP) Part 3 :

Fittings

ISO 15874: Part 3: 2003

25




DIN 16962-5: 2000

Pipe Joints and Elements for Polypropylene (PP) for Pipes

Under Pressure, PP-H 100, PP-B 80 and PP-R 80 Part 5:

General Quality Requirements, Testing.

B.2.4.2

Polypropylene (PP) Compression Fittings

for HDPE Pipes

BS 5114: 1975 (1981) Amd.2 - 1987



BS 5114: 1975 (1981) Amd.2 -

1987

ISO 3458: 1976


Pressure Pipes Test of Leakproofness Under Internal

Pressure.

ISO 3459: 1976

Polyethylene (PE) Pressure Pipes Joints Assembled with

Mechanical Fittings Internal Under-Pressure Test Method

and Requirement.

ISO 3503: 1976


Pressure Pipes Test of Leakproofness Under Internal Pressure when Subjected to

Bending.

26




ISO 3501: 1976


Pressure Pipes Test of Resistance to Pull Out.

ISO 14236: 2000

Plastics Pipes and Fittings Mechanical-Joint Compression

Fittings for Use with Polyethylene Pressure Pipes in

Water Supply Systems.

B.2.5 Glass Reinforced Plastic (GRP) Fittings

B.2.5.1

Glass Reinforced Plastic (GRP) Fittings

ISO 10639: 2004




Resin

ISO 10639: 2004

B.2.6 Mild Steel (MS) Cement Lined Fittings

B.2.6.1

Mild Steel (MS) Cement Lined Specials

(ERW & SAW)


for Water and Sewage

BS 534: 1990

MS 1968: 2007



delivery conditions.

27




B.2.7 Stainless Steel (SS) Fittings

B.2.7.1

Stainless Steel (SS) Threaded Fittings

ISO 4144: 2003 Pipework Stainless Steel

Fittings Threaded in Accordance with ISO 7-1.

ISO 4144: 2003

B.2.7.2

Stainless Steel (SS) Welded Fittings

MS 1842: 2010 (ASTM A 403)

Wrought Austenitic Stainless Steel Piping Fittings

Specification (First Revision).

MS 1842: 2010 (ASTM A 403)

B.2.7.3

Stainless Steel (SS) Press Fittings

SAS 322: 2003 Stainless Steel Press Fittings SAS 322: 2003

This standard is in Japanese Language.

There is no english version available.

B.2.8 Ductile Iron (DI) Fittings

B.2.15 Ductile Iron (DI)

Fittings MS 1919: 2006

(BS EN 545: 2002)


and Test Method

MS 1919: 2006 (BS EN 545: 2002)

B.2.9 Copper Fittings

B.2.9.1 Copper Fittings (Short

Ends & Capillary) BS EN 1254-1: 1998

Copper and Copper Alloys. Plumbing Fittings. Fittings with Short Ends for Capillary Brazing

to Copper Tubes.

BS EN 1254-1: 1998

B.2.9.2 Copper Fittings

(Compression Ends) BS EN 1254-2: 1998

Copper and Copper Alloys. Plumbing Fittings. Fittings with Compression Ends for Use with

Copper Tubes.

BS EN 1254-2: 1998

28




B.2.9.3 Copper Fittings

(Combining End) BS EN 1254-4: 1998

Copper and Copper Alloys. Plumbing Fittings. Fittings

Combining Other End Connections with Capillary or

Compression Ends.

BS EN 1254-4: 1998

B.2.10 Composite Fittings

B.2.10.1 Polysteel Fittings CJ/T 137: 2001 Malleable Iron Threaded Fittings

of Lining Plastic for Water Supply.

CJ/T 137: 2001 This standard is in Chinese

Language. There is no english version available.

B.2.10.2 Polyphenol Oxidase

(PPO) Fittings AS 4176: 1994

Polyethylene / Aluminium and Cross-linked Polyethylene /

Aluminium Macro-Composite Pipe Systems for Pressure

Applications.

AS 4176: 1994

This is only the nearest standard available.

Standard specific for this product is not available.

B.2.11 Adapter

B.2.11.1 Variable Adapter Spesifikasi JKR 20200-0045-99


and AC Pipes.


B.2.11.2 Flange Adapter Spesifikasi JKR 20200-0048-99


Adaptors.


29




B.2.11.3 Flexible Coupling Spesifikasi JKR 20200-0048-99


Adaptors.


B.2.11.4 Detachable Joint Spesifikasi JKR 20200-0045-99


and AC Pipes.


B.2.12 Saddle

B.2.12.1 Ferrous Saddle Spesifikasi JKR 20200-0044-99



B.2.12.2 2 in 1 Adjustable

Saddle

Spesifikasi JKR 20200-0044-99 CL.

17.10



CL. 17.10

B.2.12.3 PP Clamp Saddle JKR No. 1 95 (BA)

JKR Standard Specification for Polypropylene (PP) Clamp

Saddle to be Used with Polyethylene (PE) Pipes.

JKR No. 1 95 (BA)

B.2.13 Pillar Hydrant

B.2.13.1 Pillar Hydrant Spesifikasi JKR 20200-0042-99

JKR Standard Specification for Ductile Iron Pillar Hydrants.


30




MS 1395: 1996 Specification for Pillar Hydrants MS 1395: 1996

This MS Adopted the JKR No. 1 93 (BA) JKR Specification for Pillar

Hydrants.

B.2.14 Strainer

B.2.14.1 Ductile Iron (DI)

Strainer Spesifikasi JKR 20200-0100-01

JKR Standard Specification for Ductile Iron Strainer (DN 50 to

DN 600)


B.2.15 Ferrules

B.2.15.1 Swivel Ferrules Spesifikasi JKR 20200-0174-04

JKR Standard Specification for Ferrules

B.2.15.2 Under Pressure Vertical Ferrules

MS 1396: 2006 Ferrules Specification (First

Revision)

31

CATEGORY C: STORAGE OF WATER (TANK AND RESERVOIR)

C.1 TANK




CATEGORY C PRODUCT FOR STORAGE OF WATER

C.1 TANKS

C.1.1 Reinforced Concrete Reservoir / Tank

C.1.1.1 Precast Concrete Tank

C.1.2 Steel Tank

C.1.2.1

Glass Coated / Glass Lined / Glass Fused / Epoxy Coated / Epoxy

Lining

AWWA D103-97 ANSI/AWWA D103-

09

Factory-Coated Bolted Steel Tanks For Water Storage

No copy of the standard

C.1.2.2

Corrugated Steel Panel With

Polyethylene-Lined Water Storage Tank

BS 1449:Pt 1: 1991

Steel Plate, Sheet & Strip. Carbon and carbon-

manganese, sheet and strip.

BS 1449-1.1:1991, BS 1449-1.8:1991 & BS 1449-1.14:1991

SS 245:1995 (Cl. 10.2.1 & Cl 10.2.2)

Specification for Glass Reinforced Polyester Sectional

Water Tank

Cl 10.2.1 Leakage Test Cl 10.2.2 Deflection Test

C.1.2.3 Cylindrical Double

Fold System BS 5950-1:2000

Structural Use of Steelwork in Building Part 1 : Code of

Practice for Design Rolled and Welded Section.

32




C.1.3 GRP / FRP Tanks

C.1.3.1 GRP / FRP Sectional

Water Tank

SS 245 : 1995 Specification for Glass

Reinforced Polyester Sectional Water Tank

BS EN 13280: 2001

Specification for glass fibre reinforced cistern of one-piece and sectional construction for storage above ground of cold

water

MS 1390 : 2010 Glass Reinforced Polyester Panels And Panels Water

Tanks

C.1.3.2 FRP One-Piece Water

Tank

BS 7491: Pt 2 : 1992

Glass Fibre Reinforced Plastic Cisterns for Cold Water

Storage. Specification for one piece cisterns of nominal

capacity for 500L to 25000L.

Superceded and replaced by BS EN 13280 : 2001

BS EN 13280: 2001

Specification for glass fibre reinforced cistern of one-piece and sectional construction for storage above ground of cold

water

JIS A 4110 : 1989 / Amendment 1 : 2008

Glass Fibre Reinforced Plastic Water Tanks (Amendment 1)

33




C.1.3.3 Fibreglass Water Tank MS 1241:1991 Specification for Fibreglass

Water Tanks Effective Capacity of Less Than 2000L

C.1.4 Stainless Steel Water Tank

C.1.4.1 Stainless Steel Storage Tank

JKR 20200-0041-99 Stainless Steel Water Tanks

(With Effective Capacity Up to 15,000L)

CNS 9443 : 1989 Stainless Steel Storage Tanks For Rectangular / Panel

Tank

C.1.5 Polyethylene (PE) Water Tank

C.1.5.1 PE/HDPE Storage

Tank

MS 1225: Pt 1: 2007

Polyethylene (PE) Tanks For Cold Water Storage; Part 1:

Capacity up to 600G (Second Revision)

MS 1225: Pt 2: 2006

Polyethylene (PE) Tanks For Cold Water Storage; Part 2:

Capacity more than 600G (First Revision)

C.1.6 Pressed Steel Water Tank

C.1.6.1 Pressed Steel

Sectional Rectangular Tank Panel

BS 1564:1975 Specification for Pressed Steel Sectional Rectangular Tanks

C.1.6.2 Composite Stainless

Steel Tanks BS 1564:1975

Specification for Pressed Steel Sectional Rectangular Tanks

34

CATEGORY D: OTHER MECHANICAL EQUIPMENT AND INSTALLATION D.1 PUMP (BELUM ADA) D.2 VALVE D.3 METER




CATEGORY D OTHER WATERWORKS MECHANICAL EQUIPMENT AND INSTALLATION

D.2 VALVES

D.2.1 Butterfly Valve BS EN 593 : 2004

Industrial Valves. Metallic Butterfly Valve

JKR 20200-0050-99* Butterfly Valves

D.2.2 Gate Valve / Sluice

Valve

BS 5163 : 1986

Specification for Predominantly Key-Operated Cast Iron Gate

Valve For Waterworks Purposes

BS 5150 : 1990 Specification for Cast Iron Gate

Valve

Superceded & replaced by BS EN 1171

BS EN 1171 : 2002 Industrial Valves. Cast Iron

Gate Valves

JKR 20200-0077-00 Ductile Iron Type B Large

Sluice Valves (DN700 to DN 1800)

D.2.3 Air Valve / Air Release

Valve

JKR 20200-0043-99 Ductile Iron Air Valves (Revised

Edition 1999)

JKR 20200-0097-01 Ductile Iron Air Valves (Revised

Edition 2001)

35




ANSI / AWWA C512-2004

Air Release, Air Vacuum, And Combination Air Valve for

Waterworks Service.

D.2.4 Check Valve

BS EN 12334 : 2001 Industrial Valves. Cast Iron

Check Valve

BS 5153 : 1974 Specification for Cast Iron Check Valves for General

Purposes.

Superceded & Replaced by BS EN 12334:2001

TS EN 12334:2001 Industrial Valves. Cast Iron

Check Valve

D.2.5 Scour Valve - No registration yet & no

standard available for this product

D.2.6 Stopvalve BS 5412 : 1996

Specification for Low Resistance Single Taps and Combination Tap Assemblies

(Nominal Size and ) Suitable for Operation at PN 10 max. and a min. flow pressure

of 0.01MPa (0.1 bar)

D.2.7 Lockable Valve / Servicing Valve

BS EN 1213 : 2000

Building Valves. Copper Alloy Stopvalves for Potable Water Supply in Buildings. Test &

Requirement.

36




BS 6675 : 1986 Specification for Servicing

Valve (Copper Alloy) for Water Services

D.2.8 Float Operated Valve JKR 20200-0059-99* Piston Type Float Operated

Valves (Revised Edition 1999) No registration yet

D.2.9 Control Valve /

Automatic Control Valve

JKR 20200-0114-01* Ductile Iron Automatic Control

Valves for Waterworks Purposes (DN15-DN1000)

D.2.9.1 Pressure Reducing

Valve -

D.2.9.2 Altitude Valve -

D.2.9.3 Free Discharge Valve -

D.2.9.4 In-Line Throttling Valve -

D.2.9.5 Submerged Discharge

Valve -

D.2.9.6 Pressure Sustaining

Valve -

D.2.9.7 Constant Flow Valve -

D.2.9.8 Reflux Valve -

37




D.2.9.9 Backflow Preventer - No registration yet

Note : For Item D.2.9 up to D.2.9.8 The product had been registered with us but without a standard. Lately we had been informed by IKRAM about there is a standard for control valve which is JKR Spec.

38




CATEGORY D OTHER WATERWORKS MECHANICAL EQUIPMENT AND INSTALLATION

D.3 WATER METER

D.3.1 Flowmeter

D.3.1.1 Electromagnetic

Flowmeter

D.3.1.2 Ultrasonic Flowmeter

D.3.2 Volumetric Piston

Water Meter

ISO 4064-1: 2005

Measurement of Water Flow in fully charged closed conduits Meters for cold potable water

and hot water Part 1 - Specification

D.3.2.1 Plastic Volumetric

Water Meter

D.3.2.2 Brass Volumetric

Water Meter

D.3.3 Jet Water Meter

D.3.3.1 Multi- Jet Water Meter

D.3.3.2 Single Jet Water Meter

D.3.4 Woltman Water Meter

39

CATEGORY E: WATER SUPPLY PLUMBING SYSTEM

E.1 TAP E.2 VALVES E.3 FLUSHING CISTERNS E.4 BIDETS E.5 DRINKING FOUNTAIN

No. Product Standards referred by industry Standard for SPAN

registration Remarks


CATEGORY E SANITARY FITTINGS

E.1.1 Pillar Tap / Bib Tap /

Mixer / Faucet / Shower

BS 5412:1996

Specification for Low Resistance Single Taps and Combination Tap Assemblies

(Nominal Size and ) Suitable for Operation at PN 10 max. and a min. flow pressure

of 0.01MPa (0.1 bar)

BS EN 200 : 2008

Sanitary Tapware. Single Taps and combination Taps For

Water Supply Systems of Type 1 and Type 2. General Technical Specification.

Cl. 8.3, Cl.9 & Cl. 10

AS / NZS 3718 : 2005 Water Supply Tap ware

E.2.1 WC Flushing Cistern &

Flush Pipe MS 795 : 2002

Specification for WC Flushing Cisterns & Flush Pipes

E.2.2 Plastic WC Flushing MS 795 : 2002 Specification for WC Flushing

40

No. Product Standards referred by industry Standard for SPAN

registration Remarks


Cistern Cisterns & Flush Pipes

E.3 Vitreous China Water

Closet Pans MS 1522 : 2007

Vitreous China Water Closet Pans Specification (Second

Revision)

E.4 Vitreous China

Moulded One-Piece Water Closet

MS 1522 : 2007 Vitreous China Water Closet Pans Specification (Second

Revision)

MS 795 : 2002 Specification for WC Flushing

Cisterns & Flush Pipes

MS 147 : 2001 Specification For Quality of

Vitreous China Sanitary Appliances (First Revision)

E.5 Vitreous China

Sanitary Appliances MS 147 : 2001

Specification For Quality of Vitreous China Sanitary

Appliances (First Revision)

E.5.1 Urinal MS 147 : 2001

Specification For Quality of Vitreous China Sanitary Appliances (First Revision)

E.5.2 Cistern & Covers MS 147 : 2001


E.5.3 Wash Basin MS 147 : 2001


list of technical standard for water supply

Documents