log periodic antennas - lpa-lpd series
TRANSCRIPT
Log Periodic Dipole Antennas806-960 MHz
Model Number Frequency Range(MHz) H-Plane E-Plane Gain
(dBd)Fixed Electrical
Downtilt Options*Length x Width x Depth
(in inches)
LPA-4016 _ 806-941 MHz 40° 14° 16 dBd 1.25°, 5° 47.2” x 21.3” x 13.7”
LPA-4019 _ 806-941 MHz 40° 7° 19 dBd 1.25°, 3°, 5° 94.5” x 21.3” x 13.7”
LPA-80063/4CF _ 806-960 MHz 63° 15° 13 dBd 0°, 5° 47.4” x 15.2” x 13.2”
LPA-80063/6CF _ 806-960 MHz 63° 10° 14.5 dBd 0°, 2°, 5° 70.9” x 15.0” x 13.1”
LPA-80063/8CF _ 806-960 MHz 63° 7° 16 dBd 0°, 2°, 5° 94.5” x 15.2” x 13.2”
LPA-80080/4CF _ 806-960 MHz 80° 15° 12.5 dBd 0°, 5° 47.2” x 5.5” x 13.2”
LPA-80080/6CF _ 806-960 MHz 80° 10° 14 dBd 0°, 2°, 5° 70.9” x 5.5” x 13.2”
LPA-80080/8CF _ 806-960 MHz 80° 7° 15 dBd 0°, 2°, 3°, 5° 94.5” x 5.5” x 13.2”
LPA-80090/4CF _ 806-960 MHz 90° 15° 11.5 dBd 0°, 5° 47.2” x 5.5” x 9.4”
LPA-80090/8CF _ 806-960 MHz 90° 7° 14.5 dBd 0°, 3°, 5° 94.5” x 5.5” x 9.4”
LPA- 800 63 / 6 CF E-DIN 5°
Electrical Downtilt
Connector TypeNE is an elongated N connectorE-DIN is an elongated DIN connector
CF refers to a “Center-Fed” connector
Number of element setsAlso refers to the approx. length in feet
Horizontal Beamwidth
Operating Frequency Range800 = Operates within 806-960 MHz
LPA-800 Series
Our LPA (Log Periodic Antenna) 800 series is a group of log periodic dipole antennas operating within the 806-960 MHz frequencyspectrum. These vertically polarized antennas feature the same true log periodic design as our classic LPD series, but are designedfor more stringent zoning requirements with lighter weights and low profiles.
The LPA design features more active elements than industry standard log periodic antennas. This dynamic, multiple array allowsquick roll-off in the horizontal plane without impacting the half power points. The quick roll-off minimizes sector overlap, which con-tributes to the control of soft hand-off and pilot pollution.
Design and Construction of the LPA-800 Log Periodic:LPA antennas are manufactured with our exclusive 3T Technology, featuring a true log periodic design that allows for excellent front-to-side characteristics to minimize sector overlap; a unique feedline design that eliminates the need for conventional solder joints inthe signal path; a non-collinear system with access to each radiating element for control of the shaping of the vertical pattern; air asinsulation for virtually no internal signal loss; fiberglass radomes and aircraft grade aluminum reflector plates for even heat dissipa-tion to minimize plate warping and bending.
Model Number Guide:
Amphenol Antel, Inc.
Model’s Currently Available:
*Some downtilt models may operate at a different frequency range than that listed. Please consult specification sheet for actual frequency range.When ordering replace “ __” with the connector type (NE or E-DIN).
The LPA-4016 and LPA-4019 are exceptions to above example. Check specification sheet for moreinformation.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertically Polarized, Log Periodic 40° / 16 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
LPA-4016 __
Revision Date: 7/5/07
When ordering replace “___” with connector type.
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-941 MHz
Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specifications
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-102 mm (2.0-4.0 in). If the lock-downbrace is used, the maximum diameter is Ø88.9mm (3.5 in)
Mounting Bracket & Downtilt Bracket Kit #21699999
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.5) Worst case at 15° mechanical downtilt.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Frequency Range 806-941 MHz
Impedance 50Ω3) Connector(s) NE or E-DIN
1 port / center1) VSWR ≤ 1.35:1
Polarization Vertical1) Gain 16 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 40°
E-Plane 14°1) Electrical Downtilt 1.25°1) Null Fill 5%
Lightning Protection Direct Ground
True log-periodic design allows for superiorfront-to-side characteristics to minimizesector overlap.
Durable brass feedline design eliminatesthe need for conventional solder joints inthe signal path.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
Antenna available with center-fedconnector only.
Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.Aluminum reflector.
Length 1200 mm 47.2 in
Width 545 mm 21.3 inDepthDepth with z-bracket
350390
mmmm
13.715.4
inin
4) Weight 10.4 kg 23 lbs
Wind AreaFore/Aft 0.39 m2 4.20 ft2
Side 0.47 m2 5.03 ft2
5) Rated Wind Velocity (Safety factor 2.0)>277 km/hr >172 mph
Wind Load @ 100 mph (161 km/hr)Fore/Aft 600 N 135 lbsSide 609 N 137 lbs
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertically Polarized, Log Periodic 40° / 16 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
LPA-4016 __ 5°
Revision Date: 7/5/07
When ordering replace “___” with connector type.
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-941 MHz
Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specifications
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-102 mm (2.0-4.0 in). If the lock-downbrace is used, the maximum diameter is Ø88.9mm (3.5 in)
Mounting Bracket & Downtilt Bracket Kit #21699999
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.5) Worst case at 15° mechanical downtilt.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Frequency Range 806-941 MHz
Impedance 50Ω3) Connector(s) NE or E-DIN
1 port / center1) VSWR ≤ 1.35:1
Polarization Vertical1) Gain 16 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 40°
E-Plane 14°1) Electrical Downtilt 5°1) Null Fill 5%
Lightning Protection Direct Ground
True log-periodic design allows for superiorfront-to-side characteristics to minimizesector overlap.
Durable brass feedline design eliminatesthe need for conventional solder joints inthe signal path.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
Antenna available with center-fedconnector only.
Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.Aluminum reflector.
Length 1200 mm 47.2 in
Width 545 mm 21.3 inDepthDepth with z-bracket
350390
mmmm
13.715.4
inin
4) Weight 10.4 kg 23 lbs
Wind AreaFore/Aft 0.39 m2 4.20 ft2
Side 0.47 m2 5.03 ft2
5) Rated Wind Velocity (Safety factor 2.0)>277 km/hr >172 mph
Wind Load @ 100 mph (161 km/hr)Fore/Aft 600 N 135 lbsSide 609 N 137 lbs
Vertically Polarized, Log Periodic 40° / 19 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
LPA-4019 __
Revision Date: 7/5/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-941 MHz
Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specifications
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-102 mm (2.0-4.0 in). If the lock-downbrace is used, the maximum diameter is Ø88.9mm (3.5 in)
Mounting Bracket & Downtilt Bracket Kit #21699999
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.5) Worst case at 15° mechanical downtilt.
Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Frequency Range 806-941 MHz
Impedance 50Ω3) Connector(s) NE or E-DIN
1 port / center1) VSWR ≤ 1.35:1
Polarization Vertical1) Gain 19 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 40°
E-Plane 7°1) Electrical Downtilt 1.25°1) Null Fill 5%
Lightning Protection Direct Ground
True log-periodic design allows for superiorfront-to-side characteristics to minimizesector overlap.
Durable brass feedline design eliminatesthe need for conventional solder joints inthe signal path.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
Antenna available with center-fedconnector only.
Length 2400 mm 94.5 in
Width 545 mm 21.3 in
DepthDepth with z-bracket
350390
mmmm
13.715.4
inin
4) Weight 18.6 kg 41 lbs
Wind AreaFore/Aft 0.78 m2 8.35 ft2
Side 0.96 m2 10.37 ft2
5) Rated Wind Velocity (Safety factor 2.0)>192 km/hr >119 mph
Wind Load @ 100 mph (161 km/hr)Fore/Aft 1245 N 280 lbsSide 1483 N 279 lbs
Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.Aluminum reflector.
Vertically Polarized, Log Periodic 40° / 19 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
LPA-4019 __ 3°
Revision Date: 7/5/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-941 MHz
Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specifications
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-102 mm (2.0-4.0 in). If the lock-downbrace is used, the maximum diameter is Ø88.9mm (3.5 in)
Mounting Bracket & Downtilt Bracket Kit #21699999
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.5) Worst case at 15° mechanical downtilt.
Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Frequency Range 806-941 MHz
Impedance 50Ω3) Connector(s) NE or E-DIN
1 port / center1) VSWR ≤ 1.35:1
Polarization Vertical1) Gain 19 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 40°
E-Plane 7°1) Electrical Downtilt 3°1) Null Fill 5%
Lightning Protection Direct Ground
True log-periodic design allows for superiorfront-to-side characteristics to minimizesector overlap.
Durable brass feedline design eliminatesthe need for conventional solder joints inthe signal path.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
Antenna available with center-fedconnector only.
Length 2400 mm 94.5 in
Width 545 mm 21.3 in
DepthDepth with z-bracket
350390
mmmm
13.715.4
inin
4) Weight 18.6 kg 41 lbs
Wind AreaFore/Aft 0.78 m2 8.35 ft2
Side 0.96 m2 10.37 ft2
5) Rated Wind Velocity (Safety factor 2.0)>192 km/hr >119 mph
Wind Load @ 100 mph (161 km/hr)Fore/Aft 1245 N 280 lbsSide 1483 N 279 lbs
Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.Aluminum reflector.
Vertically Polarized, Log Periodic 40° / 19 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
LPA-4019 __ 5°
Revision Date: 7/5/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-900 MHz
Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specifications
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-102 mm (2.0-4.0 in). If the lock-downbrace is used, the maximum diameter is Ø88.9mm (3.5 in)
Mounting Bracket & Downtilt Bracket Kit #21699999
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.5) Worst case at 15° mechanical downtilt.
Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Frequency Range 806-900 MHz
Impedance 50Ω3) Connector(s) NE or E-DIN
1 port / center1) VSWR ≤ 1.35:1
Polarization Vertical1) Gain 19 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 40°
E-Plane 7°1) Electrical Downtilt 5°1) Null Fill 5%
Lightning Protection Direct Ground
True log-periodic design allows for superiorfront-to-side characteristics to minimizesector overlap.
Durable brass feedline design eliminatesthe need for conventional solder joints inthe signal path.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
Antenna available with center-fedconnector only.
Length 2400 mm 94.5 in
Width 545 mm 21.3 in
DepthDepth with z-bracket
350390
mmmm
13.715.4
inin
4) Weight 18.6 kg 41 lbs
Wind AreaFore/Aft 0.78 m2 8.35 ft2
Side 0.96 m2 10.37 ft2
5) Rated Wind Velocity (Safety factor 2.0)>192 km/hr >119 mph
Wind Load @ 100 mph (161 km/hr)Fore/Aft 1245 N 280 lbsSide 1483 N 279 lbs
Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.Aluminum reflector.
Vertically Polarized, Log Periodic 63° / 13 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
LPA-80063/4CF __
Revision Date: 7/5/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Featuring upper sidelobe suppression.
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-960 MHz
Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specificationsLength 1205 mm 47.4 in
Width 386 mm 15.2 inDepthDepth with z-bracket
335375
mmmm
13.214.8
inin
4) Weight 9.1 kg 20.0 lbs
Wind AreaFore/Aft 0.47 m2 5.0 ft2
Side 0.40 m2 4.4 ft2
Rated Wind Velocity (Safety factor 2.0)>351 km/hr >218 mph
Wind Load @ 100 mph (161 km/hr)Fore/Aft 665 N 149.5 lbsSide 577 N 129.6 lbs
Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-102 mm (2.0-4.0 in). If the lock-downbrace is used, the maximum diameter is Ø88.9mm (3.5 in)
Mounting Bracket and Downtilt Bracket Kit #21699999
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Frequency Range 806-960 MHz
Impedance 50Ω3) Connector(s) NE or E-DIN
1 port / center1) VSWR ≤ 1.4:1
Polarization Vertical1) Gain 13 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 63°
E-Plane 15°1) Electrical Downtilt 0°1) Null Fill 10%
Lightning Protection Direct Ground
CF Denotes a Center-FedConnector.
True log-periodic design allows for superiorfront-to-side characteristics to minimizesector overlap.
Unique feedline design eliminates the needfor conventional solder joints in the signalpath.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
Antenna available with center-fedconnector only.
Vertically Polarized, Log Periodic 63° / 13 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
LPA-80063/4CF __ 5°
Revision Date: 7/5/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Featuring upper sidelobe suppression.
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-960 MHz
Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specificationsLength 1205 mm 47.4 in
Width 386 mm 15.2 inDepthDepth with z-bracket
335375
mmmm
13.214.8
inin
4) Weight 9.1 kg 20.0 lbs
Wind AreaFore/Aft 0.47 m2 5.0 ft2
Side 0.40 m2 4.4 ft2
Rated Wind Velocity (Safety factor 2.0)>351 km/hr >218 mph
Wind Load @ 100 mph (161 km/hr)Fore/Aft 665 N 149.5 lbsSide 577 N 129.6 lbs
Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-102 mm (2.0-4.0 in). If the lock-downbrace is used, the maximum diameter is Ø88.9mm (3.5 in)
Mounting Bracket and Downtilt Bracket Kit #21699999
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Frequency Range 806-960 MHz
Impedance 50Ω3) Connector(s) NE or E-DIN
1 port / center1) VSWR ≤ 1.4:1
Polarization Vertical1) Gain 13 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 63°
E-Plane 15°1) Electrical Downtilt 5°1) Null Fill 10%
Lightning Protection Direct Ground
CF Denotes a Center-FedConnector.
True log-periodic design allows for superiorfront-to-side characteristics to minimizesector overlap.
Unique feedline design eliminates the needfor conventional solder joints in the signalpath.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
Antenna available with center-fedconnector only.
Vertically Polarized, Log Periodic 63° / 14.5 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
LPA-80063/6CF __
Revision Date: 7/5/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Featuring upper sidelobe suppression.
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-960 MHz
Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specificationsLength 1800 mm 70.9 in
Width 380 mm 15.0 inDepthDepth with z-bracket
332372
mmmm
13.114.6
inin
4) Weight 12.3 kg 27.0 lbs
Wind AreaFore/Aft 0.68 m2 7.4 ft2
Side 0.60 m2 6.5 ft2
Rated Wind Velocity (Safety factor 2.0)>235 km/hr >146 mph
Wind Load @ 100 mph (161 km/hr)Fore/Aft 993 N 223.3 lbsSide 872 N 196.1 lbs
Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-102 mm (2.0-4.0 in). If the lock-downbrace is used, the maximum diameter is Ø88.9mm (3.5 in)
Mounting Bracket & Downtilt Bracket Kit #21699999
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Frequency Range 806-960 MHz
Impedance 50Ω3) Connector(s) NE or E-DIN
1 port / center1) VSWR ≤ 1.4:1
Polarization Vertical1) Gain 14.5 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 63°
E-Plane 10°1) Electrical Downtilt 0°1) Null Fill 10%
Lightning Protection Direct Ground
CF Denotes a Center-FedConnector.
True log-periodic design allows for superiorfront-to-side characteristics to minimizesector overlap.
Unique feedline design eliminates the needfor conventional solder joints in the signalpath.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
Antenna available with center-fedconnector only.
Vertically Polarized, Log Periodic 63° / 14.5 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
LPA-80063/6CF __ 2°
Revision Date: 7/5/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Featuring upper sidelobe suppression.
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-960 MHz
Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specificationsLength 1800 mm 70.9 in
Width 380 mm 15.0 inDepthDepth with z-bracket
332372
mmmm
13.114.6
inin
4) Weight 12.3 kg 27.0 lbs
Wind AreaFore/Aft 0.68 m2 7.4 ft2
Side 0.60 m2 6.5 ft2
Rated Wind Velocity (Safety factor 2.0)>235 km/hr >146 mph
Wind Load @ 100 mph (161 km/hr)Fore/Aft 993 N 223.3 lbsSide 872 N 196.1 lbs
Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-102 mm (2.0-4.0 in). If the lock-downbrace is used, the maximum diameter is Ø88.9mm (3.5 in)
Mounting Bracket & Downtilt Bracket Kit #21699999
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Frequency Range 806-960 MHz
Impedance 50Ω3) Connector(s) NE or E-DIN
1 port / center1) VSWR ≤ 1.4:1
Polarization Vertical1) Gain 14.5 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 63°
E-Plane 10°1) Electrical Downtilt 2°1) Null Fill 10%
Lightning Protection Direct Ground
CF Denotes a Center-FedConnector.
True log-periodic design allows for superiorfront-to-side characteristics to minimizesector overlap.
Unique feedline design eliminates the needfor conventional solder joints in the signalpath.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
Antenna available with center-fedconnector only.
Vertically Polarized, Log Periodic 63° / 14.5 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
LPA-80063/6CF __ 5°
Revision Date: 7/5/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Featuring upper sidelobe suppression.
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-960 MHz
Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specificationsLength 1800 mm 70.9 in
Width 380 mm 15.0 inDepthDepth with z-bracket
332372
mmmm
13.114.6
inin
4) Weight 12.3 kg 27.0 lbs
Wind AreaFore/Aft 0.68 m2 7.4 ft2
Side 0.60 m2 6.5 ft2
Rated Wind Velocity (Safety factor 2.0)>235 km/hr >146 mph
Wind Load @ 100 mph (161 km/hr)Fore/Aft 993 N 223.3 lbsSide 872 N 196.1 lbs
Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-102 mm (2.0-4.0 in). If the lock-downbrace is used, the maximum diameter is Ø88.9mm (3.5 in)
Mounting Bracket & Downtilt Bracket Kit #21699999
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Frequency Range 806-960 MHz
Impedance 50Ω3) Connector(s) NE or E-DIN
1 port / center1) VSWR ≤ 1.4:1
Polarization Vertical1) Gain 14.5 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 63°
E-Plane 10°1) Electrical Downtilt 5°1) Null Fill 10%
Lightning Protection Direct Ground
CF Denotes a Center-FedConnector.
True log-periodic design allows for superiorfront-to-side characteristics to minimizesector overlap.
Unique feedline design eliminates the needfor conventional solder joints in the signalpath.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
Antenna available with center-fedconnector only.
Vertically Polarized, Log Periodic 63° / 16 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
LPA-80063/8CF __
Revision Date: 7/5/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Featuring upper sidelobe suppression.
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-960 MHz
Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specificationsLength 2400 mm 94.5 in
Width 386 mm 15.2 inDepthDepth with z-bracket
335375
mmmm
13.214.8
inin
4) Weight 17.2 kg 38.0 lbs
Wind AreaFore/Aft 0.93 m2 10.0 ft2
Side 0.80 m2 8.7 ft2
Rated Wind Velocity (Safety factor 2.0)>276 km/hr >172 mph
Wind Load @ 100 mph (161 km/hr)Fore/Aft 1357 N 305 lbsSide 1197 N 269 lbs
Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-102 mm (2.0-4.0 in). If the lock-downbrace is used, the maximum diameter is Ø88.9mm (3.5 in)
Mounting Bracket & Downtilt Bracket Kit #21699999
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Frequency Range 806-960 MHz
Impedance 50Ω3) Connector(s) NE or E-DIN
1 port / center1) VSWR ≤ 1.4:1
Polarization Vertical1) Gain 16 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 63°
E-Plane 7°1) Electrical Downtilt 0°1) Null Fill 10%
Lightning Protection Direct Ground
CF Denotes a Center-FedConnector.
Antenna available with center-fedconnector only.
True log-periodic design allows for superiorfront-to-side characteristics to minimizesector overlap.
Unique feedline design eliminates the needfor conventional solder joints in the signalpath.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
Vertically Polarized, Log Periodic 63° / 16 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
LPA-80063/8CF __ 2°
Revision Date: 7/5/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Featuring upper sidelobe suppression.
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-960 MHz
Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specificationsLength 2400 mm 94.5 in
Width 386 mm 15.2 inDepthDepth with z-bracket
335375
mmmm
13.214.8
inin
4) Weight 17.2 kg 38.0 lbs
Wind AreaFore/Aft 0.93 m2 10.0 ft2
Side 0.80 m2 8.7 ft2
Rated Wind Velocity (Safety factor 2.0)>276 km/hr >172 mph
Wind Load @ 100 mph (161 km/hr)Fore/Aft 1357 N 305 lbsSide 1197 N 269 lbs
Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-102 mm (2.0-4.0 in). If the lock-downbrace is used, the maximum diameter is Ø88.9mm (3.5 in)
Mounting Bracket & Downtilt Bracket Kit #21699999
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Frequency Range 806-960 MHz
Impedance 50Ω3) Connector(s) NE or E-DIN
1 port / center1) VSWR ≤ 1.4:1
Polarization Vertical1) Gain 16 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 63°
E-Plane 7°1) Electrical Downtilt 2°1) Null Fill 10%
Lightning Protection Direct Ground
CF Denotes a Center-FedConnector.
Antenna available with center-fedconnector only.
True log-periodic design allows for superiorfront-to-side characteristics to minimizesector overlap.
Unique feedline design eliminates the needfor conventional solder joints in the signalpath.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
Vertically Polarized, Log Periodic 63° / 16 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
LPA-80063/8CF __ 5°
Revision Date: 7/5/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Featuring upper sidelobe suppression.
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-960 MHz
Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specificationsLength 2400 mm 94.5 in
Width 386 mm 15.2 inDepthDepth with z-bracket
335375
mmmm
13.214.8
inin
4) Weight 17.2 kg 38.0 lbs
Wind AreaFore/Aft 0.93 m2 10.0 ft2
Side 0.80 m2 8.7 ft2
Rated Wind Velocity (Safety factor 2.0)>276 km/hr >172 mph
Wind Load @ 100 mph (161 km/hr)Fore/Aft 1357 N 305 lbsSide 1197 N 269 lbs
Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-102 mm (2.0-4.0 in). If the lock-downbrace is used, the maximum diameter is Ø88.9mm (3.5 in)
Mounting Bracket & Downtilt Bracket Kit #21699999
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Frequency Range 806-960 MHz
Impedance 50Ω3) Connector(s) NE or E-DIN
1 port / center1) VSWR ≤ 1.4:1
Polarization Vertical1) Gain 16 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 63°
E-Plane 7°1) Electrical Downtilt 5°1) Null Fill 10%
Lightning Protection Direct Ground
CF Denotes a Center-FedConnector.
Antenna available with center-fedconnector only.
True log-periodic design allows for superiorfront-to-side characteristics to minimizesector overlap.
Unique feedline design eliminates the needfor conventional solder joints in the signalpath.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
Vertically Polarized, Log Periodic 80° / 12.5 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
LPA-80080/4CF __
Revision Date: 7/5/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Featuring upper sidelobe suppression.
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-960 MHz
Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specificationsLength 1200 mm 47.2 in
Width 140 mm 5.5 inDepthDepth with z-bracket
335375
mmmm
13.214.8
inin
4) Weight 5.4 kg 12.0 lbs
Wind AreaFore/Aft 0.17 m2 1.8 ft2
Side 0.40 m2 4.3 ft2
Rated Wind Velocity (Safety factor 2.0)>369 km/hr >229 mph
Wind Load @ 100 mph (161 km/hr)Fore/Aft 254 N 57.1 lbsSide 574 N 129.0 lbs
Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-102 mm (2.0-4.0 in). If the lock-downbrace is used, the maximum diameter is Ø88.9mm (3.5 in).
Mounting Bracket & Downtilt Bracket Kit #21699999
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Frequency Range 806-960 MHz
Impedance 50Ω3) Connector(s) NE or E-DIN
1 port / center1) VSWR ≤ 1.4:1
Polarization Vertical1) Gain 12.5 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 80°
E-Plane 15°1) Electrical Downtilt 0°1) Null Fill 15%
Lightning Protection Direct Ground
CF Denotes a Center-FedConnector.
True log-periodic design allows for superiorfront-to-side characteristics to minimizesector overlap.
Unique feedline design eliminates the needfor conventional solder joints in the signalpath.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
Antenna available with center-fedconnector only.
Vertically Polarized, Log Periodic 80° / 12.5 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
LPA-80080/4CF __ 5°
Revision Date: 7/5/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Featuring upper sidelobe suppression.
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-960 MHz
Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specificationsLength 1200 mm 47.2 in
Width 140 mm 5.5 inDepthDepth with z-bracket
335375
mmmm
13.214.8
inin
4) Weight 5.4 kg 12.0 lbs
Wind AreaFore/Aft 0.17 m2 1.8 ft2
Side 0.40 m2 4.3 ft2
Rated Wind Velocity (Safety factor 2.0)>369 km/hr >229 mph
Wind Load @ 100 mph (161 km/hr)Fore/Aft 254 N 57.1 lbsSide 574 N 129.0 lbs
Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-102 mm (2.0-4.0 in). If the lock-downbrace is used, the maximum diameter is Ø88.9mm (3.5 in).
Mounting Bracket & Downtilt Bracket Kit #21699999
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Frequency Range 806-960 MHz
Impedance 50Ω3) Connector(s) NE or E-DIN
1 port / center1) VSWR ≤ 1.4:1
Polarization Vertical1) Gain 12.5 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 80°
E-Plane 15°1) Electrical Downtilt 5°1) Null Fill 15%
Lightning Protection Direct Ground
CF Denotes a Center-FedConnector.
True log-periodic design allows for superiorfront-to-side characteristics to minimizesector overlap.
Unique feedline design eliminates the needfor conventional solder joints in the signalpath.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
Antenna available with center-fedconnector only.
Vertically Polarized, Log Periodic 80° / 14 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
LPA-80080/6CF __
Revision Date: 7/5/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Featuring upper sidelobe suppression.
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-960 MHz
Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specificationsLength 1800 mm 70.9 in
Width 140 mm 5.5 inDepthDepth with z-bracket
335375
mmmm
13.214.8
inin
4) Weight 9.5 kg 21.0 lbs
Wind AreaFore/Aft 0.25 m2 2.7 ft2
Side 0.60 m2 6.5 ft2
Rated Wind Velocity (Safety factor 2.0)>295 km/hr >183 mph
Wind Load @ 100 mph (161 km/hr)Fore/Aft 415 N 93.3 lbsSide 870 N 195.6 lbs
Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-102 mm (2.0-4.0 in). If the lock-downbrace is used, the maximum diameter is Ø88.9mm (3.5 in)
Mounting Bracket & Downtilt Bracket Kit #21699999
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Frequency Range 806-960 MHz
Impedance 50Ω3) Connector(s) NE or E-DIN
1 port / center1) VSWR ≤ 1.4:1
Polarization Vertical1) Gain 14 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 80°
E-Plane 10°1) Electrical Downtilt 0°1) Null Fill 10%
Lightning Protection Direct Ground
CF Denotes a Center-FedConnector.
True log-periodic design allows for superiorfront-to-side characteristics to minimizesector overlap.
Unique feedline design eliminates the needfor conventional solder joints in the signalpath.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
Antenna available with center-fedconnector only.
Vertically Polarized, Log Periodic 80° / 14 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
LPA-80080/6CF __ 2°
Revision Date: 7/5/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Featuring upper sidelobe suppression.
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-960 MHz
Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specificationsLength 1800 mm 70.9 in
Width 140 mm 5.5 inDepthDepth with z-bracket
335375
mmmm
13.214.8
inin
4) Weight 9.5 kg 21.0 lbs
Wind AreaFore/Aft 0.25 m2 2.7 ft2
Side 0.60 m2 6.5 ft2
Rated Wind Velocity (Safety factor 2.0)>295 km/hr >183 mph
Wind Load @ 100 mph (161 km/hr)Fore/Aft 415 N 93.3 lbsSide 870 N 195.6 lbs
Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-102 mm (2.0-4.0 in). If the lock-downbrace is used, the maximum diameter is Ø88.9mm (3.5 in)
Mounting Bracket & Downtilt Bracket Kit #21699999
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Frequency Range 806-960 MHz
Impedance 50Ω3) Connector(s) NE or E-DIN
1 port / center1) VSWR ≤ 1.4:1
Polarization Vertical1) Gain 14 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 80°
E-Plane 10°1) Electrical Downtilt 2°1) Null Fill 10%
Lightning Protection Direct Ground
CF Denotes a Center-FedConnector.
True log-periodic design allows for superiorfront-to-side characteristics to minimizesector overlap.
Unique feedline design eliminates the needfor conventional solder joints in the signalpath.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
Antenna available with center-fedconnector only.
Vertically Polarized, Log Periodic 80° / 14 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
LPA-80080/6CF __ 5°
Revision Date: 7/5/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Featuring upper sidelobe suppression.
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-960 MHz
Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specificationsLength 1800 mm 70.9 in
Width 140 mm 5.5 inDepthDepth with z-bracket
335375
mmmm
13.214.8
inin
4) Weight 9.5 kg 21.0 lbs
Wind AreaFore/Aft 0.25 m2 2.7 ft2
Side 0.60 m2 6.5 ft2
Rated Wind Velocity (Safety factor 2.0)>295 km/hr >183 mph
Wind Load @ 100 mph (161 km/hr)Fore/Aft 415 N 93.3 lbsSide 870 N 195.6 lbs
Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-102 mm (2.0-4.0 in). If the lock-downbrace is used, the maximum diameter is Ø88.9mm (3.5 in)
Mounting Bracket & Downtilt Bracket Kit #21699999
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Frequency Range 806-960 MHz
Impedance 50Ω3) Connector(s) NE or E-DIN
1 port / center1) VSWR ≤ 1.4:1
Polarization Vertical1) Gain 14 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 80°
E-Plane 10°1) Electrical Downtilt 5°1) Null Fill 10%
Lightning Protection Direct Ground
CF Denotes a Center-FedConnector.
True log-periodic design allows for superiorfront-to-side characteristics to minimizesector overlap.
Unique feedline design eliminates the needfor conventional solder joints in the signalpath.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
Antenna available with center-fedconnector only.
Vertically Polarized, Log Periodic 80° / 15 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
LPA-80080/8CF __
Revision Date: 7/5/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Featuring upper sidelobe suppression.
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-960 MHz
Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specificationsLength 2400 mm 94.5 in
Width 140 mm 5.5 in
DepthDepth with z-bracket
335375
mmmm
13.214.8
inin
4) Weight 10.9 kg 24.0 lbs
Wind AreaFore/Aft 0.34 m2 3.6 ft2
Side 0.81 m2 8.7 ft2
Rated Wind Velocity (Safety factor 2.0)>340 km/hr >211 mph
Wind Load @ 100 mph (161 km/hr)Fore/Aft 580 N 130 lbsSide 1198 N 269 lbs
Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-102 mm (2.0-4.0 in). If the lock-downbrace is used, the maximum diameter is Ø88.9mm (3.5 in).
Mounting Bracket & Downtilt Bracket Kit #21699999
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Frequency Range 806-960 MHz
Impedance 50Ω3) Connector(s) NE or E-DIN
1 port / center1) VSWR ≤ 1.4:1
Polarization Vertical1) Gain 15 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 80°
E-Plane 7°1) Electrical Downtilt 0°1) Null Fill 10%
Lightning Protection Direct Ground
CF Denotes a Center-FedConnector.
True log-periodic design allows for superiorfront-to-side characteristics to minimizesector overlap.
Unique feedline design eliminates the needfor conventional solder joints in the signalpath.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
Antenna available with center-fedconnector only.
Vertically Polarized, Log Periodic 80° / 15 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
LPA-80080/8CF __ 2°
Revision Date: 7/5/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Featuring upper sidelobe suppression.
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-960 MHz
Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specificationsLength 2400 mm 94.5 in
Width 140 mm 5.5 in
DepthDepth with z-bracket
335375
mmmm
13.214.8
inin
4) Weight 10.9 kg 24.0 lbs
Wind AreaFore/Aft 0.34 m2 3.6 ft2
Side 0.81 m2 8.7 ft2
Rated Wind Velocity (Safety factor 2.0)>340 km/hr >211 mph
Wind Load @ 100 mph (161 km/hr)Fore/Aft 580 N 130 lbsSide 1198 N 269 lbs
Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-102 mm (2.0-4.0 in). If the lock-downbrace is used, the maximum diameter is Ø88.9mm (3.5 in).
Mounting Bracket & Downtilt Bracket Kit #21699999
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Frequency Range 806-960 MHz
Impedance 50Ω3) Connector(s) NE or E-DIN
1 port / center1) VSWR ≤ 1.4:1
Polarization Vertical1) Gain 15 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 80°
E-Plane 7°1) Electrical Downtilt 2°1) Null Fill 10%
Lightning Protection Direct Ground
CF Denotes a Center-FedConnector.
True log-periodic design allows for superiorfront-to-side characteristics to minimizesector overlap.
Unique feedline design eliminates the needfor conventional solder joints in the signalpath.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
Antenna available with center-fedconnector only.
Vertically Polarized, Log Periodic 80° / 15 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
LPA-80080/8CF __ 3°
Revision Date: 7/5/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Featuring upper sidelobe suppression.
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-960 MHz
Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specificationsLength 2400 mm 94.5 in
Width 140 mm 5.5 in
DepthDepth with z-bracket
335375
mmmm
13.214.8
inin
4) Weight 10.9 kg 24.0 lbs
Wind AreaFore/Aft 0.34 m2 3.6 ft2
Side 0.81 m2 8.7 ft2
Rated Wind Velocity (Safety factor 2.0)>340 km/hr >211 mph
Wind Load @ 100 mph (161 km/hr)Fore/Aft 580 N 130 lbsSide 1198 N 269 lbs
Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-102 mm (2.0-4.0 in). If the lock-downbrace is used, the maximum diameter is Ø88.9mm (3.5 in).
Mounting Bracket & Downtilt Bracket Kit #21699999
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Frequency Range 806-960 MHz
Impedance 50Ω3) Connector(s) NE or E-DIN
1 port / center1) VSWR ≤ 1.4:1
Polarization Vertical1) Gain 15 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 80°
E-Plane 7°1) Electrical Downtilt 3°1) Null Fill 10%
Lightning Protection Direct Ground
CF Denotes a Center-FedConnector.
True log-periodic design allows for superiorfront-to-side characteristics to minimizesector overlap.
Unique feedline design eliminates the needfor conventional solder joints in the signalpath.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
Antenna available with center-fedconnector only.
Vertically Polarized, Log Periodic 80° / 15 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
LPA-80080/8CF __ 5°
Revision Date: 7/5/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Featuring upper sidelobe suppression.
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-960 MHz
Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specificationsLength 2400 mm 94.5 in
Width 140 mm 5.5 in
DepthDepth with z-bracket
335375
mmmm
13.214.8
inin
4) Weight 10.9 kg 24.0 lbs
Wind AreaFore/Aft 0.34 m2 3.6 ft2
Side 0.81 m2 8.7 ft2
Rated Wind Velocity (Safety factor 2.0)>340 km/hr >211 mph
Wind Load @ 100 mph (161 km/hr)Fore/Aft 580 N 130 lbsSide 1198 N 269 lbs
Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-102 mm (2.0-4.0 in). If the lock-downbrace is used, the maximum diameter is Ø88.9mm (3.5 in).
Mounting Bracket & Downtilt Bracket Kit #21699999
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Frequency Range 806-960 MHz
Impedance 50Ω3) Connector(s) NE or E-DIN
1 port / center1) VSWR ≤ 1.4:1
Polarization Vertical1) Gain 15 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 80°
E-Plane 7°1) Electrical Downtilt 5°1) Null Fill 10%
Lightning Protection Direct Ground
CF Denotes a Center-FedConnector.
True log-periodic design allows for superiorfront-to-side characteristics to minimizesector overlap.
Unique feedline design eliminates the needfor conventional solder joints in the signalpath.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
Antenna available with center-fedconnector only.
Vertically Polarized, Log Periodic 90° / 11.5 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
LPA-80090/4CF __
Revision Date: 7/5/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Featuring upper sidelobe suppression.
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-960 MHz
Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specificationsLength 1200 mm 47.2 in
Width 140 mm 5.5 inDepthDepth with z-bracket
240280
mmmm
9.411.0
inin
4) Weight 5 kg 11.0 lbs
Wind AreaFore/Aft 0.17 m2 1.8 ft2
Side 0.29 m2 3.1 ft2
Rated Wind Velocity (Safety factor 2.0)>444 km/hr >276 mph
Wind Load @ 100 mph (161 km/hr)Fore/Aft 254 N 57.1 lbsSide 415 N 93.3 lbs
Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-102 mm (2.0-4.0 in). If the lock-downbrace is used, the maximum diameter is Ø88.9mm (3.5 in).
Mounting Bracket & Downtilt Bracket Kit #21699999
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Frequency Range 806-960 MHz
Impedance 50Ω3) Connector(s) NE or E-DIN
1 port / center1) VSWR ≤ 1.4:1
Polarization Vertical1) Gain 11.5 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 90°
E-Plane 15°1) Electrical Downtilt 0°1) Null Fill 10-15%
Lightning Protection Direct Ground
CF Denotes a Center-FedConnector.
True log-periodic design allows for superiorfront-to-side characteristics to minimizesector overlap.
Unique feedline design eliminates the needfor conventional solder joints in the signalpath.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
Antenna available with center-fedconnector only.
Vertically Polarized, Log Periodic 90° / 11.5 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
LPA-80090/4CF __ 5°
Revision Date: 7/5/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Featuring upper sidelobe suppression.
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-960 MHz
Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specificationsLength 1200 mm 47.2 in
Width 140 mm 5.5 inDepthDepth with z-bracket
240280
mmmm
9.411.0
inin
4) Weight 5 kg 11.0 lbs
Wind AreaFore/Aft 0.17 m2 1.8 ft2
Side 0.29 m2 3.1 ft2
Rated Wind Velocity (Safety factor 2.0)>444 km/hr >276 mph
Wind Load @ 100 mph (161 km/hr)Fore/Aft 254 N 57.1 lbsSide 415 N 93.3 lbs
Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-102 mm (2.0-4.0 in). If the lock-downbrace is used, the maximum diameter is Ø88.9mm (3.5 in).
Mounting Bracket & Downtilt Bracket Kit #21699999
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Frequency Range 806-960 MHz
Impedance 50Ω3) Connector(s) NE or E-DIN
1 port / center1) VSWR ≤ 1.4:1
Polarization Vertical1) Gain 11.5 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 90°
E-Plane 15°1) Electrical Downtilt 5°1) Null Fill 10-15%
Lightning Protection Direct Ground
CF Denotes a Center-FedConnector.
True log-periodic design allows for superiorfront-to-side characteristics to minimizesector overlap.
Unique feedline design eliminates the needfor conventional solder joints in the signalpath.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
Antenna available with center-fedconnector only.
Vertically Polarized, Log Periodic 90° / 14.5 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
LPA-80090/8CF __
Revision Date: 7/5/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Featuring upper sidelobe suppression.
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-960 MHz
Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specificationsLength 2400 mm 94.5 in
Width 140 mm 5.5 inDepthDepth with z-bracket
240280
mmmm
9.411.0
inin
4) Weight 10 kg 22.0 lbs
Wind AreaFore/Aft 0.34 m2 3.6 ft2
Side 0.58 m2 6.2 ft2
Rated Wind Velocity (Safety factor 2.0)>340 km/hr >211 mph
Wind Load @ 100 mph (161 km/hr)Fore/Aft 582 N 131.0 lbsSide 896 N 201.5 lbs
Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-102 mm (2.0-4.0 in). If the lock-downbrace is used, the maximum diameter is Ø88.9mm (3.5 in).
Mounting Bracket & Downtilt Bracket Kit #21699999
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Frequency Range 806-960 MHz
Impedance 50Ω3) Connector(s) NE or E-DIN
1 port / center1) VSWR ≤ 1.4:1
Polarization Vertical1) Gain 14.5 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 90°
E-Plane 7°1) Electrical Downtilt 0°1) Null Fill 15%
Lightning Protection Direct Ground
CF Denotes a Center-FedConnector.
True log-periodic design allows for superiorfront-to-side characteristics to minimizesector overlap.
Unique feedline design eliminates the needfor conventional solder joints in the signalpath.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
Antenna available with center-fedconnector only.
Vertically Polarized, Log Periodic 90° / 14.5 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
LPA-80090/8CF __ 3°
Revision Date: 7/5/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Featuring upper sidelobe suppression.
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-960 MHz
Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specificationsLength 2400 mm 94.5 in
Width 140 mm 5.5 inDepthDepth with z-bracket
240280
mmmm
9.411.0
inin
4) Weight 10 kg 22.0 lbs
Wind AreaFore/Aft 0.34 m2 3.6 ft2
Side 0.58 m2 6.2 ft2
Rated Wind Velocity (Safety factor 2.0)>340 km/hr >211 mph
Wind Load @ 100 mph (161 km/hr)Fore/Aft 582 N 131.0 lbsSide 896 N 201.5 lbs
Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-102 mm (2.0-4.0 in). If the lock-downbrace is used, the maximum diameter is Ø88.9mm (3.5 in).
Mounting Bracket & Downtilt Bracket Kit #21699999
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Frequency Range 806-960 MHz
Impedance 50Ω3) Connector(s) NE or E-DIN
1 port / center1) VSWR ≤ 1.4:1
Polarization Vertical1) Gain 14.5 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 90°
E-Plane 7°1) Electrical Downtilt 3°1) Null Fill 5%
Lightning Protection Direct Ground
CF Denotes a Center-FedConnector.
True log-periodic design allows for superiorfront-to-side characteristics to minimizesector overlap.
Unique feedline design eliminates the needfor conventional solder joints in the signalpath.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
Antenna available with center-fedconnector only.
Vertically Polarized, Log Periodic 90° / 14.5 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
LPA-80090/8CF __ 5°
Revision Date: 7/5/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Featuring upper sidelobe suppression.
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-960 MHz
Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specificationsLength 2400 mm 94.5 in
Width 140 mm 5.5 inDepthDepth with z-bracket
240280
mmmm
9.411.0
inin
4) Weight 10 kg 22.0 lbs
Wind AreaFore/Aft 0.34 m2 3.6 ft2
Side 0.58 m2 6.2 ft2
Rated Wind Velocity (Safety factor 2.0)>340 km/hr >211 mph
Wind Load @ 100 mph (161 km/hr)Fore/Aft 582 N 131.0 lbsSide 896 N 201.5 lbs
Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-102 mm (2.0-4.0 in). If the lock-downbrace is used, the maximum diameter is Ø88.9mm (3.5 in).
Mounting Bracket & Downtilt Bracket Kit #21699999
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Frequency Range 806-960 MHz
Impedance 50Ω3) Connector(s) NE or E-DIN
1 port / center1) VSWR ≤ 1.4:1
Polarization Vertical1) Gain 14.5 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 90°
E-Plane 7°1) Electrical Downtilt 5°1) Null Fill 5%
Lightning Protection Direct Ground
CF Denotes a Center-FedConnector.
True log-periodic design allows for superiorfront-to-side characteristics to minimizesector overlap.
Unique feedline design eliminates the needfor conventional solder joints in the signalpath.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
Antenna available with center-fedconnector only.
1300 Capital Drive Rockford, IL 61109 Toll-Free (888) 417-9562 Tel. (815) 399-0001 Fax. (815) 399-0156 Email: [email protected] www.antelinc.com
Mounting & Downtilt Bracket Kits
LPA Bracket Kits Part Number Bracket Type
21699999 Standard LPA Mounting & Downtilt Bracket Kit* for: LPA-4016 LPA-4019 LPA-80063/4CF LPA-80063/6CF LPA-80063/8CF LPA-80080/4CF LPA-80080/6CF LPA-80080/8CF LPA-80090/4CF LPA-80090/8CF
*The LPA downtilt bracket kit includes the standard mounting kit.
Mounting Bracket Kits are sold separately and not included in the price of antennas.
21699999 Top View
Side View
Vertically Polarized Log Periodic Dipole Antennas806-900 MHz, 806-941 MHz, 806-960 MHz
Model Number Frequency Range(MHz) H-Plane E-Plane Gain
(dBd)Fixed Electrical
Downtilt Options**Length x Width x Depth
(in inches)
LPD-4013 _ 806-900 MHz* 40° 30° 13 dBd 1.25° 23.6” x 21.3” x 13.7”
LPD-4016 _ 806-941 MHz* 40° 14° 16 dBd 1.25°, 3°, 5°, 9° 47.2” x 21.3” x 13.7”
LPD-4019 _ 806-960 MHz 40° 7° 19 dBd 1.25°, 3°, 5° 94.5” x 21.3” x 13.7”
LPD-7908 _ 806-900 MHz* 60° 53° 8 dBd 0° 11.8” x 5.1” x 25.2”
LPD-7908/2 _ 806-900 MHz* 60° 26° 11 dBd 0° 23.6” x 5.1” x 25.2”
LPD-7908/4 _ 806-900 MHz* 60° 13° 14 dBd 1.25°, 3°, 5°, 9° 47.3” x 5.1” x 25.2”
LPD-6513 _ 806-941 MHz* 65° 15° 13 dBd 1.25°, 3°, 5°, 9° 47.2” x 13.9” x 11.2”
LPD Series
The LPD (Log Periodic Dipole) series is a group of log periodic antennas operating within the 806-900 MHz, 806-941 MHz, and 806-960 MHz frequency range. These antennas are an ideal choice for sectorized sites in which performance is the priority. LPD’s offera true log periodic design with more active elements than industry standard antennas. This dynamic, multiple array allows quick roll-off in the horizontal plane without impacting the half power points. The quick roll-off minimizes sector overlap, which contributes tothe control of soft hand-off and pilot pollution.
Design and Construction of the LPD Log Periodic:LPD antennas are manufactured. with our exclusive 3T Technology, featuring a true log periodic design that allows for excellent front-to-side characteristics to minimize sector overlap; a unique feedline design that eliminates the need for conventional solder joints inthe signal path; a non-collinear system with access to each radiating element for control of the shaping of the vertical pattern; air asinsulation for virtually no internal signal loss; fiberglass radomes and aircraft grade aluminum reflector plates for even heat dissipa-tion to minimize plate warping and bending.
Model Number Guide:
Amphenol Antel, Inc.
Model’s Currently Available:
LPD 790 8 / 4 E-DIN 3°
Electrical DowntiltConnector TypeNE is an elongated N connectorE-DIN is an elongated DIN connector
References Antenna Length in Feet
Horizontal Beamwidth: “8” = 60°,“7” = 80°, “5” = 92°Operating Frequency Range790 = Operates within 806-960 MHz
Exceptions: The following antenna models are exceptions to the examples shown above:LPD-4016, LPD-4019, LPD-6513, and LPD-6516LPD 65 13 E-DIN 5°
Electrical Downtilt
Connector TypeNE is an elongated N connectorE-DIN is an elongated DIN connector
Gain in dBd
Horizontal Beamwidth
This rule does not apply to the LPD-7905/4/102 and LPD-7905/8/102.
*This model is also available up to 960 MHz. Contact your sales representative for details.**Some downtilt models may operate at a different frequency range than that listed. Please consult specification sheet for actual frequency range.When ordering replace “__” with the connector type (NE or E-DIN).
Continued on next page ...
Model Number Frequency Range(MHz) H-Plane E-Plane Gain
(dBd)Fixed Electrical
Downtilt Options**Length x Width x Depth
(in inches)
LPD-6516 _ 806-960 MHz* 65° 7° 16 dBd 1.25°, 3°, 5° 94.5” x 13.9” x 11.2”
LPD-7907 _ 806-900 MHz* 80° 56° 7 dBd 0° 11.8” x 5.1” x 14.8”
LPD-7907/2 _ 806-900 MHz* 80° 28° 10 dBd 0° 23.6” x 5.1” x 14.8”
LPD-7907/4 _ 806-960 MHz 80° 14° 13 dBd 1.25°, 3°, 5°, 9° 47.2” x 5.1” x 14.8”
LPD-7907/8 _ 806-900 MHz* 80° 7° 16 dBd 1.25°, 3°, 5° 94.5” x 5.1” x 14.8”
LPD-7905 _ 806-941 MHz* 92° 60° 5 dBd 0° 11.8” x 5.1” x 9.6”
LPD-7905/2 _ 806-900 MHz* 92° 30° 8 dBd 0° 23.6” x 5.1” x 9.6”
LPD-7905/4 _ 806-941 MHz* 92° 15° 11.5 dBd 1.25°, 3°, 5°, 9° 47.2” x 5.1” x 9.6”
LPD-7905/8 _ 806-960 MHz 92° 7° 14.5 dBd 1.25°, 3°, 5° 94.5” x 5.1” x 9.6”
LPD-7905/4/102 _ 806-941 MHz* 102° 15° 10.5 dBd 1.25°, 3°, 5°, 9° 47.2” x 5.1” x 9.6”
LPD-7905/8/102 _ 806-941 MHz* 102° 7° 13.5 dBd 1.25°, 3°, 5° 94.5” x 5.1” x 9.6”
Amphenol Antel, Inc.
Model’s Currently Available:
LPD Series Continued
*This model is also available up to 960 MHz. Contact your sales representative for details.**Some downtilt models may operate at a different frequency range than that listed. Please consult specification sheet for actual frequency range.When ordering replace “__” with the connector type (NE or E-DIN).
Vertically Polarized, Log Periodic 40° / 13 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
LPD-4013 __
Revision Date: 7/5/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-900 MHz
Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specificationsLength 600 mm 23.6 in
Width 545 mm 21.3 in
Depth 350 mm 13.7 in4) Weight 7.7 kg 17.0 lbs
Wind AreaFore/Aft 0.19 m2 2.0 ft2
Side 0.22 m2 2.4 ft2
Rated Wind Velocity (Safety factor 2.0)>531 km/hr >330 mph
Wind Load @ 100 mph (161 km/hr)Fore/Aft 282 N 63 lbsSide 326 N 73 lbs
Antenna consisting of brass and covered by afiberglass radome. Aluminum reflector.
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).
Mounting bracket kit #36110002Downtilt bracket kit #36114001
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Frequency Range 806-900 MHz*
Impedance 50Ω3) Connector(s) NE or E-DIN
1 port / center1) VSWR ≤ 1.25:1
Polarization Vertical1) Gain 13 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 40°
E-Plane 30°1) Electrical Downtilt 1.25°1) Null Fill 5%
Lightning Protection Direct Ground
True log-periodic design allows for superiorfront-to-side characteristics to minimizesector overlap.
Durable brass feedline design eliminatesthe need for conventional solder joints inthe signal path.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
*Also available up to 960 MHz. Consult your salesdirector for more information.
Antenna available with center-fedconnector only.
No Nulls in the
H-Plane
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertically Polarized, Log Periodic 40° / 16 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
LPD-4016 __
Revision Date: 7/5/07
When ordering replace “___” with connector type.
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-941 MHz
Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specifications
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).
Mounting bracket kit #36110003Downtilt bracket kit #36114002
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Frequency Range 806-941 MHz*
Impedance 50Ω3) Connector(s) NE or E-DIN
1 port / center1) VSWR ≤ 1.25:1
Polarization Vertical1) Gain 16 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 40°
E-Plane 14°1) Electrical Downtilt 1.25°1) Null Fill 5%
Lightning Protection Direct Ground
True log-periodic design allows for superiorfront-to-side characteristics to minimizesector overlap.
Durable brass feedline design eliminatesthe need for conventional solder joints inthe signal path.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
*Also available up to 960 MHz. Consult your salesdirector for more information. Antenna available with center-fed
connector only.
Antenna consisting of brass and covered by afiberglass radome. Aluminum reflector.
This model has beenreplaced with the
LPA-4016 _
Length 1200 mm 47.2 in
Width 545 mm 21.3 in
Depth 350 mm 13.7 in4) Weight 15.4 kg 34.0 lbs
Wind AreaFore/Aft 0.38 m2 4.05 ft2
Side 0.47 m2 5.05 ft2
5) Rated Wind Velocity (Safety factor 2.0)>443 km/hr >275 mph
Wind Load @ 100 mph (161 km/hr)Fore/Aft 578 N 130 lbsSide 694 N 156 lbs
No Nulls in the
H-Plane
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertically Polarized, Log Periodic 40° / 16 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
LPD-4016 __ 3°
Revision Date: 7/5/07
When ordering replace “___” with connector type.
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-941 MHz
Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specifications
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).
Mounting bracket kit #36110003Downtilt bracket kit #36114002
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Frequency Range 806-941 MHz*
Impedance 50Ω3) Connector(s) NE or E-DIN
1 port / center1) VSWR ≤ 1.25:1
Polarization Vertical1) Gain 16 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 40°
E-Plane 14°1) Electrical Downtilt 3°1) Null Fill 5%
Lightning Protection Direct Ground
True log-periodic design allows for superiorfront-to-side characteristics to minimizesector overlap.
Durable brass feedline design eliminatesthe need for conventional solder joints inthe signal path.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
*Also available up to 960 MHz. Consult your salesdirector for more information. Antenna available with center-fed
connector only.
Antenna consisting of brass and covered by afiberglass radome. Aluminum reflector.
Length 1200 mm 47.2 in
Width 545 mm 21.3 in
Depth 350 mm 13.7 in4) Weight 15.4 kg 34.0 lbs
Wind AreaFore/Aft 0.38 m2 4.05 ft2
Side 0.47 m2 5.05 ft2
5) Rated Wind Velocity (Safety factor 2.0)>443 km/hr >275 mph
Wind Load @ 100 mph (161 km/hr)Fore/Aft 578 N 130 lbsSide 694 N 156 lbs
No Nulls in the
H-Plane
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertically Polarized, Log Periodic 40° / 16 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
LPD-4016 __ 5°
Revision Date: 7/5/07
When ordering replace “___” with connector type.
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-941 MHz
Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specifications
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).
Mounting bracket kit #36110003Downtilt bracket kit #36114002
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Frequency Range 806-941 MHz*
Impedance 50Ω3) Connector(s) NE or E-DIN
1 port / center1) VSWR ≤ 1.25:1
Polarization Vertical1) Gain 16 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 40°
E-Plane 14°1) Electrical Downtilt 5°1) Null Fill 5%
Lightning Protection Direct Ground
True log-periodic design allows for superiorfront-to-side characteristics to minimizesector overlap.
Durable brass feedline design eliminatesthe need for conventional solder joints inthe signal path.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
*Also available up to 960 MHz. Consult your salesdirector for more information. Antenna available with center-fed
connector only.
Antenna consisting of brass and covered by afiberglass radome. Aluminum reflector.
This model has beenreplaced with the
LPA-4016 _ 5°
Length 1200 mm 47.2 in
Width 545 mm 21.3 in
Depth 350 mm 13.7 in4) Weight 15.4 kg 34.0 lbs
Wind AreaFore/Aft 0.38 m2 4.05 ft2
Side 0.47 m2 5.05 ft2
5) Rated Wind Velocity (Safety factor 2.0)>443 km/hr >275 mph
Wind Load @ 100 mph (161 km/hr)Fore/Aft 578 N 130 lbsSide 694 N 156 lbs
No Nulls in the
H-Plane
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertically Polarized, Log Periodic 40° / 16 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
LPD-4016 __ 9°
Revision Date: 7/5/07
When ordering replace “___” with connector type.
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-941 MHz
Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specifications
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).
Mounting bracket kit #36110003Downtilt bracket kit #36114002
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Frequency Range 806-941 MHz*
Impedance 50Ω3) Connector(s) NE or E-DIN
1 port / center1) VSWR ≤ 1.25:1
Polarization Vertical1) Gain 16 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 40°
E-Plane 14°1) Electrical Downtilt 9°1) Null Fill 5%
Lightning Protection Direct Ground
True log-periodic design allows for superiorfront-to-side characteristics to minimizesector overlap.
Durable brass feedline design eliminatesthe need for conventional solder joints inthe signal path.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
*Also available up to 960 MHz. Consult your salesdirector for more information. Antenna available with center-fed
connector only.
Antenna consisting of brass and covered by afiberglass radome. Aluminum reflector.
Length 1200 mm 47.2 in
Width 545 mm 21.3 in
Depth 350 mm 13.7 in4) Weight 15.4 kg 34.0 lbs
Wind AreaFore/Aft 0.38 m2 4.05 ft2
Side 0.47 m2 5.05 ft2
5) Rated Wind Velocity (Safety factor 2.0)>443 km/hr >275 mph
Wind Load @ 100 mph (161 km/hr)Fore/Aft 578 N 130 lbsSide 694 N 156 lbs
No Nulls in the
H-Plane
Vertically Polarized, Log Periodic 40° / 19 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
LPD-4019 __
Revision Date: 7/5/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-960 MHz
Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specifications
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).
Mounting bracket kit #36110003Downtilt bracket kit #36114002
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Frequency Range 806-960 MHz
Impedance 50Ω3) Connector(s) NE or E-DIN
1 port / center1) VSWR ≤ 1.25:1
Polarization Vertical1) Gain 19 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 40°
E-Plane 7°1) Electrical Downtilt 1.25°1) Null Fill 5%
Lightning Protection Direct Ground
True log-periodic design allows for superiorfront-to-side characteristics to minimizesector overlap.
Durable brass feedline design eliminatesthe need for conventional solder joints inthe signal path.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
Antenna available with center-fedconnector only.
Antenna consisting of brass and covered by afiberglass radome. Aluminum reflector.
Length 2400 mm 94.5 in
Width 545 mm 21.3 in
Depth 350 mm 13.7 in4) Weight 30.9 kg 68.0 lbs
Wind AreaFore/Aft 0.75 m2 8.1 ft2
Side 0.95 m2 10.2 ft2
5) Rated Wind Velocity (Safety factor 2.0)>311 km/hr >193 mph
Wind Load @ 100 mph (161 km/hr)Fore/Aft 1206 N 271 lbsSide 1450 N 326 lbs
No Nulls in the
H-Plane
This model has beenreplaced with the
LPA-4019 _.
Vertically Polarized, Log Periodic 40° / 19 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
LPD-4019 __ 3°
Revision Date: 7/5/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-960 MHz
Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specifications
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).
Mounting bracket kit #36110003Downtilt bracket kit #36114002
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Frequency Range 806-960 MHz
Impedance 50Ω3) Connector(s) NE or E-DIN
1 port / center1) VSWR ≤ 1.25:1
Polarization Vertical1) Gain 19 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 40°
E-Plane 7°1) Electrical Downtilt 3°1) Null Fill 5%
Lightning Protection Direct Ground
True log-periodic design allows for superiorfront-to-side characteristics to minimizesector overlap.
Durable brass feedline design eliminatesthe need for conventional solder joints inthe signal path.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
Antenna available with center-fedconnector only.
Antenna consisting of brass and covered by afiberglass radome. Aluminum reflector.
Length 2400 mm 94.5 in
Width 545 mm 21.3 in
Depth 350 mm 13.7 in4) Weight 30.9 kg 68.0 lbs
Wind AreaFore/Aft 0.75 m2 8.1 ft2
Side 0.95 m2 10.2 ft2
5) Rated Wind Velocity (Safety factor 2.0)>311 km/hr >193 mph
Wind Load @ 100 mph (161 km/hr)Fore/Aft 1206 N 271 lbsSide 1450 N 326 lbs
This model has beenreplaced with the LPA-4019 _ 3°.
Vertically Polarized, Log Periodic 40° / 19 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
LPD-4019 __ 5°
Revision Date: 7/5/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-960 MHz
Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specifications
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).
Mounting bracket kit #36110003Downtilt bracket kit #36114002
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Frequency Range 806-900 MHz*
Impedance 50Ω3) Connector(s) NE or E-DIN
1 port / center1) VSWR ≤ 1.25:1
Polarization Vertical1) Gain 19 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 40°
E-Plane 7°1) Electrical Downtilt1) Null Fill 5%
Lightning Protection Direct Ground
True log-periodic design allows for superiorfront-to-side characteristics to minimizesector overlap.
Durable brass feedline design eliminatesthe need for conventional solder joints inthe signal path.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
*Also available up to 960 MHz. Consult your salesdirector for more information. Antenna available with center-fed
connector only.
Antenna consisting of brass and covered by afiberglass radome. Aluminum reflector.
Length 2400 mm 94.5 in
Width 545 mm 21.3 in
Depth 350 mm 13.7 in4) Weight 30.9 kg 68.0 lbs
Wind AreaFore/Aft 0.75 m2 8.1 ft2
Side 0.95 m2 10.2 ft2
5) Rated Wind Velocity (Safety factor 2.0)>311 km/hr >193 mph
Wind Load @ 100 mph (161 km/hr)Fore/Aft 1206 N 271 lbsSide 1450 N 326 lbs
This model has beenreplaced with the LPA-4019 _ 5°.
Vertically Polarized, Log Periodic 60° / 8 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
LPD-7908 __
Revision Date: 7/5/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-900 MHz
Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specifications
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).
Mounting bracket kit #36110002Downtilt bracket kit #36114001
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Frequency Range 806-900 MHz*
Impedance 50Ω3) Connector(s) NE or E-DIN
1 port / center1) VSWR ≤ 1.25:1
Polarization Vertical1) Gain 8 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 60°
E-Plane 53°
Lightning Protection Direct Ground
True log-periodic design allows for superiorfront-to-side characteristics to minimizesector overlap.
Durable brass feedline design eliminatesthe need for conventional solder joints inthe signal path.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
*Also available up to 960 MHz. Consult your salesdirector for more information. Antenna available with center-fed
connector only.
Antenna consisting of brass and covered by afiberglass radome.
Length 300 mm 11.8 in
Width 130 mm 5.1 in
Depth 640 mm 25.2 in4) Weight 3.5 kg 7.7 lbs
Wind AreaFore/Aft 0.04 m2 0.42 ft2
Side 0.09 m2 0.97 ft2
5) Rated Wind Velocity (Safety factor 2.0)>512 km/hr >381 mph
Wind Load @ 100 mph (161 km/hr)Fore/Aft 56 N 12.5 lbsSide 129 N 29.0 lbs
Vertically Polarized, Log Periodic 60° / 11 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
LPD-7908/2 __
Revision Date: 7/5/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-900 MHz
Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specifications
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).
Mounting bracket kit #36110002Downtilt bracket kit #36114001
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Frequency Range 806-900 MHz*
Impedance 50Ω3) Connector(s) NE or E-DIN
1 port / center1) VSWR ≤ 1.25:1
Polarization Vertical1) Gain 11 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 60°
E-Plane 26°
Lightning Protection Direct Ground
True log-periodic design allows for superiorfront-to-side characteristics to minimizesector overlap.
Durable brass feedline design eliminatesthe need for conventional solder joints inthe signal path.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
*Also available up to 960 MHz. Consult your salesdirector for more information. Antenna available with center-fed
connector only.
Antenna consisting of brass and covered by afiberglass radome.
Length 600 mm 23.6 in
Width 130 mm 5.1 in
Depth 640 mm 25.2 in4) Weight 7.3 kg 16.2 lbs
Wind AreaFore/Aft 0.08 m2 0.84 ft2
Side 0.28 m2 3.04 ft2
5) Rated Wind Velocity (Safety factor 2.0)>338 km/hr >210 mph
Wind Load @ 100 mph (161 km/hr)Fore/Aft 112 N 25 lbsSide 400 N 90 lbs
Vertically Polarized, Log Periodic 60° / 14 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
LPD-7908/4 __
Revision Date: 7/5/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-900 MHz
Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specifications
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).
Mounting bracket kit #36110003Downtilt bracket kit #36114002
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Frequency Range 806-900 MHz*
Impedance 50Ω3) Connector(s) NE or E-DIN
1 port / center1) VSWR ≤ 1.25:1
Polarization Vertical1) Gain 14 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 60°
E-Plane 13°1) Electrical Downtilt 1.25°1) Null Fill 5%
Lightning Protection Direct Ground
True log-periodic design allows for superiorfront-to-side characteristics to minimizesector overlap.
Durable brass feedline design eliminatesthe need for conventional solder joints inthe signal path.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
*Also available up to 960 MHz. Consult your salesdirector for more information. Antenna available with center-fed
connector only.
Antenna consisting of brass and covered by afiberglass radome.
Length 1200 mm 47.3 in
Width 130 mm 5.1 in
Depth 640 mm 25.2 in4) Weight 16 kg 35.3 lbs
Wind AreaFore/Aft 0.16 m2 1.68 ft2
Side 0.66 m2 7.06 ft2
5) Rated Wind Velocity (Safety factor 2.0)>269 km/hr >168 mph
Wind Load @ 100 mph (161 km/hr)Fore/Aft 240 N 54 lbsSide 930 N 209 lbs
Vertically Polarized, Log Periodic 60° / 14 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
LPD-7908/4 __ 3°
Revision Date: 7/5/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-900 MHz
Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specifications
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).
Mounting bracket kit #36110003Downtilt bracket kit #36114002
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Frequency Range 806-900 MHz*
Impedance 50Ω3) Connector(s) NE or E-DIN
1 port / center1) VSWR ≤ 1.25:1
Polarization Vertical1) Gain 14 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 60°
E-Plane 13°1) Electrical Downtilt 3°1) Null Fill 5%
Lightning Protection Direct Ground
True log-periodic design allows for superiorfront-to-side characteristics to minimizesector overlap.
Durable brass feedline design eliminatesthe need for conventional solder joints inthe signal path.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
*Also available up to 960 MHz. Consult your salesdirector for more information. Antenna available with center-fed
connector only.
Antenna consisting of brass and covered by afiberglass radome.
Length 1200 mm 47.3 in
Width 130 mm 5.1 in
Depth 640 mm 25.2 in4) Weight 16 kg 35.3 lbs
Wind AreaFore/Aft 0.16 m2 1.68 ft2
Side 0.66 m2 7.06 ft2
5) Rated Wind Velocity (Safety factor 2.0)>269 km/hr >168 mph
Wind Load @ 100 mph (161 km/hr)Fore/Aft 240 N 54 lbsSide 930 N 209 lbs
Vertically Polarized, Log Periodic 60° / 14 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
LPD-7908/4 __ 5°
Revision Date: 7/5/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-900 MHz
Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specifications
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).
Mounting bracket kit #36110003Downtilt bracket kit #36114002
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Frequency Range 806-900 MHz*
Impedance 50Ω3) Connector(s) NE or E-DIN
1 port / center1) VSWR ≤ 1.25:1
Polarization Vertical1) Gain 14 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 60°
E-Plane 13°1) Electrical Downtilt 5°1) Null Fill 5%
Lightning Protection Direct Ground
True log-periodic design allows for superiorfront-to-side characteristics to minimizesector overlap.
Durable brass feedline design eliminatesthe need for conventional solder joints inthe signal path.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
*Also available up to 960 MHz. Consult your salesdirector for more information. Antenna available with center-fed
connector only.
Antenna consisting of brass and covered by afiberglass radome.
Length 1200 mm 47.3 in
Width 130 mm 5.1 in
Depth 640 mm 25.2 in4) Weight 16 kg 35.3 lbs
Wind AreaFore/Aft 0.16 m2 1.68 ft2
Side 0.66 m2 7.06 ft2
5) Rated Wind Velocity (Safety factor 2.0)>269 km/hr >168 mph
Wind Load @ 100 mph (161 km/hr)Fore/Aft 240 N 54 lbsSide 930 N 209 lbs
Vertically Polarized, Log Periodic 60° / 14 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
LPD-7908/4 __ 9°
Revision Date: 7/5/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-900 MHz
Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specifications
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).
Mounting bracket kit #36110003Downtilt bracket kit #36114002
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Frequency Range 806-900 MHz*
Impedance 50Ω3) Connector(s) NE or E-DIN
1 port / center1) VSWR ≤ 1.25:1
Polarization Vertical1) Gain 14 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 60°
E-Plane 13°1) Electrical Downtilt 9°1) Null Fill 5%
Lightning Protection Direct Ground
True log-periodic design allows for superiorfront-to-side characteristics to minimizesector overlap.
Durable brass feedline design eliminatesthe need for conventional solder joints inthe signal path.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
*Also available up to 960 MHz. Consult your salesdirector for more information. Antenna available with center-fed
connector only.
Antenna consisting of brass and covered by afiberglass radome.
Length 1200 mm 47.3 in
Width 130 mm 5.1 in
Depth 640 mm 25.2 in4) Weight 16 kg 35.3 lbs
Wind AreaFore/Aft 0.16 m2 1.68 ft2
Side 0.66 m2 7.06 ft2
5) Rated Wind Velocity (Safety factor 2.0)>269 km/hr >168 mph
Wind Load @ 100 mph (161 km/hr)Fore/Aft 240 N 54 lbsSide 930 N 209 lbs
Vertically Polarized, Log Periodic 65° / 13 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
LPD-6513 __
Revision Date: 7/5/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-941 MHz
Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specifications
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).
Mounting bracket kit #36110003Downtilt bracket kit #36114002
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Frequency Range 806-941 MHz*
Impedance 50Ω3) Connector(s) NE or E-DIN
1 port / center1) VSWR ≤ 1.35:1
Polarization Vertical1) Gain 13 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 65°
E-Plane 15°1) Electrical Downtilt 1.25°1) Null Fill 5%
Lightning Protection Direct Ground
True log-periodic design allows for superiorfront-to-side characteristics to minimizesector overlap.
Durable brass feedline design eliminatesthe need for conventional solder joints inthe signal path.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
*Also available up to 960 MHz. Consult your salesdirector for more information. Antenna available with center-fed
connector only.
Antenna consisting of brass and covered by afiberglass radome. Aluminum reflector.
Length 1200 mm 47.2 in
Width 355 mm 14.0 in
Depth 285 mm 11.2 in4) Weight 10 kg 28.0 lbs
Wind AreaFore/Aft 0.31 m2 3.28 ft2
Side 0.40 m2 4.29 ft2
5) Rated Wind Velocity (Safety factor 2.0)>499 km/hr >310 mph
Wind Load @ 100 mph (161 km/hr)Fore/Aft 475 N 107 lbsSide 593 N 133 lbs
Vertically Polarized, Log Periodic 65° / 13 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
LPD-6513 __ 3°
Revision Date: 7/5/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-941 MHz
Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specifications
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).
Mounting bracket kit #36110003Downtilt bracket kit #36114002
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Frequency Range 806-941 MHz*
Impedance 50Ω3) Connector(s) NE or E-DIN
1 port / center1) VSWR ≤ 1.35:1
Polarization Vertical1) Gain 13 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 65°
E-Plane 15°1) Electrical Downtilt 3°1) Null Fill 5%
Lightning Protection Direct Ground
True log-periodic design allows for superiorfront-to-side characteristics to minimizesector overlap.
Durable brass feedline design eliminatesthe need for conventional solder joints inthe signal path.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
*Also available up to 960 MHz. Consult your salesdirector for more information. Antenna available with center-fed
connector only.
Antenna consisting of brass and covered by afiberglass radome. Aluminum reflector.
Length 1200 mm 47.2 in
Width 355 mm 14.0 in
Depth 285 mm 11.2 in4) Weight 10 kg 28.0 lbs
Wind AreaFore/Aft 0.31 m2 3.28 ft2
Side 0.40 m2 4.29 ft2
5) Rated Wind Velocity (Safety factor 2.0)>499 km/hr >310 mph
Wind Load @ 100 mph (161 km/hr)Fore/Aft 475 N 107 lbsSide 593 N 133 lbs
Vertically Polarized, Log Periodic 65° / 13 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
LPD-6513 __ 5°
Revision Date: 7/5/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-941 MHz
Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specifications
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).
Mounting bracket kit #36110003Downtilt bracket kit #36114002
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Frequency Range 806-941 MHz*
Impedance 50Ω3) Connector(s) NE or E-DIN
1 port / center1) VSWR ≤ 1.35:1
Polarization Vertical1) Gain 13 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 65°
E-Plane 15°1) Electrical Downtilt 5°1) Null Fill 5%
Lightning Protection Direct Ground
True log-periodic design allows for superiorfront-to-side characteristics to minimizesector overlap.
Durable brass feedline design eliminatesthe need for conventional solder joints inthe signal path.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
*Also available up to 960 MHz. Consult your salesdirector for more information. Antenna available with center-fed
connector only.
Antenna consisting of brass and covered by afiberglass radome. Aluminum reflector.
Length 1200 mm 47.2 in
Width 355 mm 14.0 in
Depth 285 mm 11.2 in4) Weight 10 kg 28.0 lbs
Wind AreaFore/Aft 0.31 m2 3.28 ft2
Side 0.40 m2 4.29 ft2
5) Rated Wind Velocity (Safety factor 2.0)>499 km/hr >310 mph
Wind Load @ 100 mph (161 km/hr)Fore/Aft 475 N 107 lbsSide 593 N 133 lbs
Vertically Polarized, Log Periodic 65° / 13 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
LPD-6513 __ 9°
Revision Date: 7/5/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-941 MHz
Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specifications
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).
Mounting bracket kit #36110003Downtilt bracket kit #36114002
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Frequency Range 806-941 MHz*
Impedance 50Ω3) Connector(s) NE or E-DIN
1 port / center1) VSWR ≤ 1.35:1
Polarization Vertical1) Gain 13 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 65°
E-Plane 15°1) Electrical Downtilt 9°1) Null Fill 5%
Lightning Protection Direct Ground
True log-periodic design allows for superiorfront-to-side characteristics to minimizesector overlap.
Durable brass feedline design eliminatesthe need for conventional solder joints inthe signal path.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
*Also available up to 960 MHz. Consult your salesdirector for more information. Antenna available with center-fed
connector only.
Antenna consisting of brass and covered by afiberglass radome. Aluminum reflector.
Length 1200 mm 47.2 in
Width 355 mm 14.0 in
Depth 285 mm 11.2 in4) Weight 10 kg 28.0 lbs
Wind AreaFore/Aft 0.31 m2 3.28 ft2
Side 0.40 m2 4.29 ft2
5) Rated Wind Velocity (Safety factor 2.0)>499 km/hr >310 mph
Wind Load @ 100 mph (161 km/hr)Fore/Aft 475 N 107 lbsSide 593 N 133 lbs
Vertically Polarized, Log Periodic 65° / 16 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
LPD-6516 __
Revision Date: 7/5/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-960 MHz
Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specifications
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).
Mounting bracket kit #36110003Downtilt bracket kit #36114002
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Frequency Range 806-960 MHz
Impedance 50Ω3) Connector(s) NE or E-DIN
1 port / center1) VSWR ≤ 1.35:1
Polarization Vertical1) Gain 16 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 65°
E-Plane 7°1) Electrical Downtilt 1.25°1) Null Fill 5%
Lightning Protection Direct Ground
True log-periodic design allows for superiorfront-to-side characteristics to minimizesector overlap.
Durable brass feedline design eliminatesthe need for conventional solder joints inthe signal path.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
Antenna available with center-fedconnector only.
Antenna consisting of brass and covered by afiberglass radome. Aluminum reflector.
Length 2400 mm 94.5 in
Width 355 mm 14.0 in
Depth 285 mm 11.2 in4) Weight 27.4 kg 60.5 lbs
Wind AreaFore/Aft 0.61 m2 6.51 ft2
Side 0.81 m2 8.69 ft2
5) Rated Wind Velocity (Safety factor 2.0)>344 km/hr >214 mph
Wind Load @ 100 mph (161 km/hr)Fore/Aft 966 N 224 lbsSide 1244 N 280 lbs
Vertically Polarized, Log Periodic 65° / 16 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
LPD-6516 __ 3°
Revision Date: 7/5/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-960 MHz
Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specifications
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).
Mounting bracket kit #36110003Downtilt bracket kit #36114002
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Frequency Range 806-960 MHz
Impedance 50Ω3) Connector(s) NE or E-DIN
1 port / center1) VSWR ≤ 1.35:1
Polarization Vertical1) Gain 16 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 65°
E-Plane 7°1) Electrical Downtilt 3°1) Null Fill 5%
Lightning Protection Direct Ground
True log-periodic design allows for superiorfront-to-side characteristics to minimizesector overlap.
Durable brass feedline design eliminatesthe need for conventional solder joints inthe signal path.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
Antenna available with center-fedconnector only.
Antenna consisting of brass and covered by afiberglass radome. Aluminum reflector.
Length 2400 mm 94.5 in
Width 355 mm 14.0 in
Depth 285 mm 11.2 in4) Weight 27.4 kg 60.5 lbs
Wind AreaFore/Aft 0.61 m2 6.51 ft2
Side 0.81 m2 8.69 ft2
5) Rated Wind Velocity (Safety factor 2.0)>344 km/hr >214 mph
Wind Load @ 100 mph (161 km/hr)Fore/Aft 966 N 224 lbsSide 1244 N 280 lbs
Vertically Polarized, Log Periodic 65° / 16 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
LPD-6516 __ 5°
Revision Date: 7/5/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-900 MHz
Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specifications
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).
Mounting bracket kit #36110003Downtilt bracket kit #36114002
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Frequency Range 806-900 MHz*
Impedance 50Ω3) Connector(s) NE or E-DIN
1 port / center1) VSWR ≤ 1.35:1
Polarization Vertical1) Gain 16 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 65°
E-Plane 7°1) Electrical Downtilt 5°1) Null Fill 5%
Lightning Protection Direct Ground
True log-periodic design allows for superiorfront-to-side characteristics to minimizesector overlap.
Durable brass feedline design eliminatesthe need for conventional solder joints inthe signal path.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
*Also available up to 960 MHz. Consult your salesdirector for more information. Antenna available with center-fed
connector only.
Antenna consisting of brass and covered by afiberglass radome. Aluminum reflector.
Length 2400 mm 94.5 in
Width 355 mm 14.0 in
Depth 285 mm 11.2 in4) Weight 27.4 kg 60.5 lbs
Wind AreaFore/Aft 0.61 m2 6.51 ft2
Side 0.81 m2 8.69 ft2
5) Rated Wind Velocity (Safety factor 2.0)>344 km/hr >214 mph
Wind Load @ 100 mph (161 km/hr)Fore/Aft 966 N 224 lbsSide 1244 N 280 lbs
Vertically Polarized, Log Periodic 80° / 7 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
LPD-7907 __
Revision Date: 7/5/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-900 MHz
Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specifications
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).
Mounting bracket kit #36110002Downtilt bracket kit #36114001
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Frequency Range 806-900 MHz*
Impedance 50Ω3) Connector(s) NE or E-DIN
1 port / center1) VSWR ≤ 1.25:1
Polarization Vertical1) Gain 7 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 80°
E-Plane 56°
Electrical Downtilt 0°
Lightning Protection Direct Ground
True log-periodic design allows for superiorfront-to-side characteristics to minimizesector overlap.
Durable brass feedline design eliminatesthe need for conventional solder joints inthe signal path.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
*Also available up to 960 MHz. Consult your salesdirector for more information. Antenna available with center-fed
connector only.
Antenna consisting of brass and covered by afiberglass radome.
Length 300 mm 11.8 in
Width 130 mm 5.1 in
Depth 375 mm 14.8 in4) Weight 2.5 kg 5.5 lbs
Wind AreaFore/Aft 0.04 m2 0.42 ft2
Side 0.08 m2 0.83 ft2
5) Rated Wind Velocity (Safety factor 2.0)>945 km/hr >587 mph
Wind Load @ 100 mph (161 km/hr)Fore/Aft 56 N 13 lbsSide 109 N 25 lbs
Vertically Polarized, Log Periodic 80° / 10 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
LPD-7907/2 __
Revision Date: 7/5/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-900 MHz
Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specifications
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).
Mounting bracket kit #36110002Downtilt bracket kit #36114001
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Frequency Range 806-900 MHz*
Impedance 50Ω3) Connector(s) NE or E-DIN
1 port / center1) VSWR ≤ 1.25:1
Polarization Vertical1) Gain 10 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 80°
E-Plane 28°
Electrical Downtilt 0°
Lightning Protection Direct Ground
True log-periodic design allows for superiorfront-to-side characteristics to minimizesector overlap.
Durable brass feedline design eliminatesthe need for conventional solder joints inthe signal path.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
*Also available up to 960 MHz. Consult your salesdirector for more information. Antenna available with center-fed
connector only.
Antenna consisting of brass and covered by afiberglass radome.
Length 600 mm 23.6 in
Width 130 mm 5.1 in
Depth 375 mm 14.8 in4) Weight 5.5 kg 12.2 lbs
Wind AreaFore/Aft 0.08 m2 0.84 ft2
Side 0.19 m2 2.03 ft2
5) Rated Wind Velocity (Safety factor 2.0)>517 km/hr >321 mph
Wind Load @ 100 mph (161 km/hr)Fore/Aft 112 N 25 lbsSide 267 N 60 lbs
Vertically Polarized, Log Periodic 80° / 13 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
LPD-7907/4 __
Revision Date: 7/5/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-960 MHz
Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specifications
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).
Mounting bracket kit #36110003Downtilt bracket kit #36114002
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Frequency Range 806-960 MHz
Impedance 50Ω3) Connector(s) NE or E-DIN
1 port / center1) VSWR ≤ 1.25:1
Polarization Vertical1) Gain 13 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 80°
E-Plane 14°1) Electrical Downtilt 1.25°1) Null Fill 5%
Lightning Protection Direct Ground
True log-periodic design allows for superiorfront-to-side characteristics to minimizesector overlap.
Durable brass feedline design eliminatesthe need for conventional solder joints inthe signal path.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
Antenna available with center-fedconnector only.
Antenna consisting of brass and covered by afiberglass radome.
Length 1200 mm 47.2 in
Width 130 mm 5.1 in
Depth 375 mm 14.8 in4) Weight 12 kg 26.5 lbs
Wind AreaFore/Aft 0.16 m2 1.68 ft2
Side 0.41 m2 4.46 ft2
5) Rated Wind Velocity (Safety factor 2.0)>420 km/hr >261 mph
Wind Load @ 100 mph (161 km/hr)Fore/Aft 240 N 54 lbsSide 590 N 133 lbs
Vertically Polarized, Log Periodic 80° / 13 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
LPD-7907/4 __ 3°
Revision Date: 7/5/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-960 MHz
Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specifications
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).
Mounting bracket kit #36110003Downtilt bracket kit #36114002
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Frequency Range 806-960 MHz
Impedance 50Ω3) Connector(s) NE or E-DIN
1 port / center1) VSWR ≤ 1.25:1
Polarization Vertical1) Gain 13 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 80°
E-Plane 14°1) Electrical Downtilt 3°1) Null Fill 5%
Lightning Protection Direct Ground
True log-periodic design allows for superiorfront-to-side characteristics to minimizesector overlap.
Durable brass feedline design eliminatesthe need for conventional solder joints inthe signal path.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
. Antenna available with center-fedconnector only.
Antenna consisting of brass and covered by afiberglass radome.
Length 1200 mm 47.2 in
Width 130 mm 5.1 in
Depth 375 mm 14.8 in4) Weight 12 kg 26.5 lbs
Wind AreaFore/Aft 0.16 m2 1.68 ft2
Side 0.41 m2 4.46 ft2
5) Rated Wind Velocity (Safety factor 2.0)>420 km/hr >261 mph
Wind Load @ 100 mph (161 km/hr)Fore/Aft 240 N 54 lbsSide 590 N 133 lbs
Vertically Polarized, Log Periodic 80° / 13 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
LPD-7907/4 __ 5°
Revision Date: 7/5/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-900 MHz
Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specifications
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).
Mounting bracket kit #36110003Downtilt bracket kit #36114002
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Frequency Range 806-900 MHz*
Impedance 50Ω3) Connector(s) NE or E-DIN
1 port / center1) VSWR ≤ 1.25:1
Polarization Vertical1) Gain 13 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 80°
E-Plane 14°1) Electrical Downtilt 5°1) Null Fill 5%
Lightning Protection Direct Ground
True log-periodic design allows for superiorfront-to-side characteristics to minimizesector overlap.
Durable brass feedline design eliminatesthe need for conventional solder joints inthe signal path.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
*Also available up to 960 MHz. Consult your salesdirector for more information. Antenna available with center-fed
connector only.
Antenna consisting of brass and covered by afiberglass radome.
Length 1200 mm 47.2 in
Width 130 mm 5.1 in
Depth 375 mm 14.8 in4) Weight 12 kg 26.5 lbs
Wind AreaFore/Aft 0.16 m2 1.68 ft2
Side 0.41 m2 4.46 ft2
5) Rated Wind Velocity (Safety factor 2.0)>420 km/hr >261 mph
Wind Load @ 100 mph (161 km/hr)Fore/Aft 240 N 54 lbsSide 590 N 133 lbs
Vertically Polarized, Log Periodic 80° / 13 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
LPD-7907/4 __ 9°
Revision Date: 7/5/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-900 MHz
Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specifications
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).
Mounting bracket kit #36110003Downtilt bracket kit #36114002
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Frequency Range 806-900 MHz*
Impedance 50Ω3) Connector(s) NE or E-DIN
1 port / center1) VSWR ≤ 1.25:1
Polarization Vertical1) Gain 13 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 80°
E-Plane 14°1) Electrical Downtilt 9°1) Null Fill 5%
Lightning Protection Direct Ground
True log-periodic design allows for superiorfront-to-side characteristics to minimizesector overlap.
Durable brass feedline design eliminatesthe need for conventional solder joints inthe signal path.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
*Also available up to 960 MHz. Consult your salesdirector for more information. Antenna available with center-fed
connector only.
Antenna consisting of brass and covered by afiberglass radome.
Length 1200 mm 47.2 in
Width 130 mm 5.1 in
Depth 375 mm 14.8 in4) Weight 12 kg 26.5 lbs
Wind AreaFore/Aft 0.16 m2 1.68 ft2
Side 0.41 m2 4.46 ft2
5) Rated Wind Velocity (Safety factor 2.0)>420 km/hr >261 mph
Wind Load @ 100 mph (161 km/hr)Fore/Aft 240 N 54 lbsSide 590 N 133 lbs
Vertically Polarized, Log Periodic 80° / 16 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
LPD-7907/8 __
Revision Date: 7/5/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-900 MHz
Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specifications
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).
Mounting bracket kit #36110003Downtilt bracket kit #36114002
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Frequency Range 806-900 MHz*
Impedance 50Ω3) Connector(s) NE or E-DIN
1 port / center1) VSWR ≤ 1.25:1
Polarization Vertical1) Gain 16 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 80°
E-Plane 7°1) Electrical Downtilt 1.25°1) Null Fill 5%
Lightning Protection Direct Ground
True log-periodic design allows for superiorfront-to-side characteristics to minimizesector overlap.
Durable brass feedline design eliminatesthe need for conventional solder joints inthe signal path.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
*Also available up to 960 MHz. Consult your salesdirector for more information. Antenna available with center-fed
connector only.
Antenna consisting of brass and covered by afiberglass radome.
Length 2400 mm 94.5 in
Width 130 mm 5.1 in
Depth 375 mm 14.8 in4) Weight 25 kg 55.0 lbs
Wind AreaFore/Aft 0.31 m2 3.36 ft2
Side 0.83 m2 8.90 ft2
5) Rated Wind Velocity (Safety factor 2.0)>291 km/hr >181 mph
Wind Load @ 100 mph (161 km/hr)Fore/Aft 552 N 124 lbsSide 1217 N 274 lbs
Vertically Polarized, Log Periodic 80° / 16 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
LPD-7907/8 __ 3°
Revision Date: 7/5/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-941 MHz
Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specifications
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).
Mounting bracket kit #36110003Downtilt bracket kit #36114002
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Frequency Range 806-941 MHz*
Impedance 50Ω3) Connector(s) NE or E-DIN
1 port / center1) VSWR ≤ 1.25:1
Polarization Vertical1) Gain 16 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 80°
E-Plane 7°1) Electrical Downtilt 3°1) Null Fill 5%
Lightning Protection Direct Ground
True log-periodic design allows for superiorfront-to-side characteristics to minimizesector overlap.
Durable brass feedline design eliminatesthe need for conventional solder joints inthe signal path.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
*Also available up to 960 MHz. Consult your salesdirector for more information. Antenna available with center-fed
connector only.
Antenna consisting of brass and covered by afiberglass radome.
Length 2400 mm 94.5 in
Width 130 mm 5.1 in
Depth 375 mm 14.8 in4) Weight 25 kg 55.0 lbs
Wind AreaFore/Aft 0.31 m2 3.36 ft2
Side 0.83 m2 8.90 ft2
5) Rated Wind Velocity (Safety factor 2.0)>291 km/hr >181 mph
Wind Load @ 100 mph (161 km/hr)Fore/Aft 552 N 124 lbsSide 1217 N 274 lbs
Vertically Polarized, Log Periodic 80° / 16 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
LPD-7907/8 __ 5°
Revision Date: 7/5/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-900 MHz
Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specifications
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).
Mounting bracket kit #36110003Downtilt bracket kit #36114002
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Frequency Range 806-900 MHz*
Impedance 50Ω3) Connector(s) NE or E-DIN
1 port / center1) VSWR ≤ 1.25:1
Polarization Vertical1) Gain 16 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 80°
E-Plane 7°1) Electrical Downtilt 5°1) Null Fill 5%
Lightning Protection Direct Ground
True log-periodic design allows for superiorfront-to-side characteristics to minimizesector overlap.
Durable brass feedline design eliminatesthe need for conventional solder joints inthe signal path.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
*Also available up to 960 MHz. Consult your salesdirector for more information. Antenna available with center-fed
connector only.
Antenna consisting of brass and covered by afiberglass radome.
Length 2400 mm 94.5 in
Width 130 mm 5.1 in
Depth 375 mm 14.8 in4) Weight 25 kg 55.0 lbs
Wind AreaFore/Aft 0.31 m2 3.36 ft2
Side 0.83 m2 8.90 ft2
5) Rated Wind Velocity (Safety factor 2.0)>291 km/hr >181 mph
Wind Load @ 100 mph (161 km/hr)Fore/Aft 552 N 124 lbsSide 1217 N 274 lbs
Vertically Polarized, Log Periodic 92° / 5 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
LPD-7905 __
Revision Date: 7/5/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-941 MHz
Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specifications
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).
Mounting bracket kit #36110002Downtilt bracket kit #36114001
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Frequency Range 806-941 MHz*
Impedance 50Ω3) Connector(s) NE or E-DIN
1 port / center1) VSWR ≤ 1.25:1
Polarization Vertical1) Gain 5 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 92°
E-Plane 60°
Electrical Downtilt 0°
Lightning Protection Direct Ground
True log-periodic design allows for superiorfront-to-side characteristics to minimizesector overlap.
Durable brass feedline design eliminatesthe need for conventional solder joints inthe signal path.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
*Also available up to 960 MHz. Consult your salesdirector for more information. Antenna available with center-fed
connector only.
Antenna consisting of brass and covered by afiberglass radome.
Length 300 mm 11.8 in
Width 130 mm 5.1 in
Depth 245 mm 9.6 in4) Weight 2.2 kg 4.9 lbs
Wind AreaFore/Aft 0.04 m2 0.42 ft2
Side 0.05 m2 0.58 ft2
5) Rated Wind Velocity (Safety factor 2.0)>1098 km/hr >682 mph
Wind Load @ 100 mph (161 km/hr)Fore/Aft 56 N 13 lbsSide 76 N 17 lbs
Vertically Polarized, Log Periodic 92° / 8 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
LPD-7905/2 __
Revision Date: 7/5/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-900 MHz
Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specifications
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).
Mounting bracket kit #36110002Downtilt bracket kit #36114001
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Frequency Range 806-900 MHz*
Impedance 50Ω3) Connector(s) NE or E-DIN
1 port / center1) VSWR ≤ 1.25:1
Polarization Vertical1) Gain 8 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 92°
E-Plane 30°
Electrical Downtilt 0°
Lightning Protection Direct Ground
True log-periodic design allows for superiorfront-to-side characteristics to minimizesector overlap.
Durable brass feedline design eliminatesthe need for conventional solder joints inthe signal path.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
*Also available up to 960 MHz. Consult your salesdirector for more information. Antenna available with center-fed
connector only.
Antenna consisting of brass and covered by afiberglass radome.
Length 600 mm 23.6 in
Width 130 mm 5.1 in
Depth 245 mm 9.6 in4) Weight 4.5 kg 10.0 lbs
Wind AreaFore/Aft 0.08 m2 0.84 ft2
Side 0.13 m2 1.34 ft2
5) Rated Wind Velocity (Safety factor 2.0)>731 km/hr >454 mph
Wind Load @ 100 mph (161 km/hr)Fore/Aft 112 N 25 lbsSide 177 N 40 lbs
Vertically Polarized, Log Periodic 92° / 11.5 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
LPD-7905/4 __
Revision Date: 7/5/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-941 MHz
Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specifications
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).
Mounting bracket kit #36110003Downtilt bracket kit #36114002
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Frequency Range 806-941 MHz*
Impedance 50Ω3) Connector(s) NE or E-DIN
1 port / center1) VSWR ≤ 1.25:1
Polarization Vertical1) Gain 11.5 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 92°
E-Plane 15°1) Electrical Downtilt 1.25°1) Null Fill 5%
Lightning Protection Direct Ground
True log-periodic design allows for superiorfront-to-side characteristics to minimizesector overlap.
Durable brass feedline design eliminatesthe need for conventional solder joints inthe signal path.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
*Also available up to 960 MHz. Consult your salesdirector for more information. Antenna available with center-fed
connector only.
Antenna consisting of brass and covered by afiberglass radome.
Length 1200 mm 47.2 in
Width 130 mm 5.1 in
Depth 245 mm 9.6 in4) Weight 10 kg 22.1 lbs
Wind AreaFore/Aft 0.16 m2 1.68 ft2
Side 0.27 m2 2.95 ft2
5) Rated Wind Velocity (Safety factor 2.0)>599 km/hr >372 mph
Wind Load @ 100 mph (161 km/hr)Fore/Aft 240 N 54 lbsSide 394 N 89 lbs
Vertically Polarized, Log Periodic 92° / 11.5 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
LPD-7905/4 __ 3°
Revision Date: 7/5/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-941 MHz
Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specifications
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).
Mounting bracket kit #36110003Downtilt bracket kit #36114002
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Frequency Range 806-941 MHz*
Impedance 50Ω3) Connector(s) NE or E-DIN
1 port / center1) VSWR ≤ 1.25:1
Polarization Vertical1) Gain 11.5 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 92°
E-Plane 15°1) Electrical Downtilt 3°1) Null Fill 5%
Lightning Protection Direct Ground
True log-periodic design allows for superiorfront-to-side characteristics to minimizesector overlap.
Durable brass feedline design eliminatesthe need for conventional solder joints inthe signal path.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
*Also available up to 960 MHz. Consult your salesdirector for more information. Antenna available with center-fed
connector only.
Antenna consisting of brass and covered by afiberglass radome.
Length 1200 mm 47.2 in
Width 130 mm 5.1 in
Depth 245 mm 9.6 in4) Weight 10 kg 22.1 lbs
Wind AreaFore/Aft 0.16 m2 1.68 ft2
Side 0.27 m2 2.95 ft2
5) Rated Wind Velocity (Safety factor 2.0)>599 km/hr >372 mph
Wind Load @ 100 mph (161 km/hr)Fore/Aft 240 N 54 lbsSide 394 N 89 lbs
Vertically Polarized, Log Periodic 92° / 11.5 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
LPD-7905/4 __ 5°
Revision Date: 7/5/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-941 MHz
Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specifications
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).
Mounting bracket kit #36110003Downtilt bracket kit #36114002
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Frequency Range 806-941 MHz*
Impedance 50Ω3) Connector(s) NE or E-DIN
1 port / center1) VSWR ≤ 1.25:1
Polarization Vertical1) Gain 11.5 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 92°
E-Plane 15°1) Electrical Downtilt 5°1) Null Fill 5%
Lightning Protection Direct Ground
True log-periodic design allows for superiorfront-to-side characteristics to minimizesector overlap.
Durable brass feedline design eliminatesthe need for conventional solder joints inthe signal path.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
*Also available up to 960 MHz. Consult your salesdirector for more information. Antenna available with center-fed
connector only.
Antenna consisting of brass and covered by afiberglass radome.
Length 1200 mm 47.2 in
Width 130 mm 5.1 in
Depth 245 mm 9.6 in4) Weight 10 kg 22.1 lbs
Wind AreaFore/Aft 0.16 m2 1.68 ft2
Side 0.27 m2 2.95 ft2
5) Rated Wind Velocity (Safety factor 2.0)>599 km/hr >372 mph
Wind Load @ 100 mph (161 km/hr)Fore/Aft 240 N 54 lbsSide 394 N 89 lbs
Vertically Polarized, Log Periodic 92° / 11.5 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
LPD-7905/4 __ 9°
Revision Date: 7/5/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-941 MHz
Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specifications
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).
Mounting bracket kit #36110003Downtilt bracket kit #36114002
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Frequency Range 806-941 MHz*
Impedance 50Ω3) Connector(s) NE or E-DIN
1 port / center1) VSWR ≤ 1.25:1
Polarization Vertical1) Gain 11.5 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 92°
E-Plane 15°1) Electrical Downtilt 9°1) Null Fill 5%
Lightning Protection Direct Ground
True log-periodic design allows for superiorfront-to-side characteristics to minimizesector overlap.
Durable brass feedline design eliminatesthe need for conventional solder joints inthe signal path.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
*Also available up to 960 MHz. Consult your salesdirector for more information. Antenna available with center-fed
connector only.
Antenna consisting of brass and covered by afiberglass radome.
Length 1200 mm 47.2 in
Width 130 mm 5.1 in
Depth 245 mm 9.6 in4) Weight 10 kg 22.1 lbs
Wind AreaFore/Aft 0.16 m2 1.68 ft2
Side 0.27 m2 2.95 ft2
5) Rated Wind Velocity (Safety factor 2.0)>599 km/hr >372 mph
Wind Load @ 100 mph (161 km/hr)Fore/Aft 240 N 54 lbsSide 394 N 89 lbs
Vertically Polarized, Log Periodic 92° / 14.5 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
LPD-7905/8 __
Revision Date: 7/5/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-960 MHz
Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specifications
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).
Mounting bracket kit #36110003Downtilt bracket kit #36114002
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Frequency Range 806-960 MHz
Impedance 50Ω3) Connector(s) NE or E-DIN
1 port / center1) VSWR ≤ 1.25:1
Polarization Vertical1) Gain 14.5 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 92°
E-Plane 7°1) Electrical Downtilt 1.25°1) Null Fill 5%
Lightning Protection Direct Ground
True log-periodic design allows for superiorfront-to-side characteristics to minimizesector overlap.
Durable brass feedline design eliminatesthe need for conventional solder joints inthe signal path.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
Antenna available with center-fedconnector only.
Antenna consisting of brass and covered by afiberglass radome.
Length 2400 mm 94.5 in
Width 130 mm 5.1 in
Depth 245 mm 9.6 in4) Weight 22 kg 48.7 lbs
Wind AreaFore/Aft 0.31 m2 3.36 ft2
Side 0.56 m2 6.07 ft2
5) Rated Wind Velocity (Safety factor 2.0)>403 km/hr >250 mph
Wind Load @ 100 mph (161 km/hr)Fore/Aft 552 N 124 lbsSide 872 N 196 lbs
Vertically Polarized, Log Periodic 92° / 14.5 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
LPD-7905/8 __ 3°
Revision Date: 7/5/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-960 MHz
Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specifications
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).
Mounting bracket kit #36110003Downtilt bracket kit #36114002
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Frequency Range 806-960 MHz
Impedance 50Ω3) Connector(s) NE or E-DIN
1 port / center1) VSWR ≤ 1.25:1
Polarization Vertical1) Gain 14.5 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 92°
E-Plane 7°1) Electrical Downtilt 3°1) Null Fill 5%
Lightning Protection Direct Ground
True log-periodic design allows for superiorfront-to-side characteristics to minimizesector overlap.
Durable brass feedline design eliminatesthe need for conventional solder joints inthe signal path.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
Antenna available with center-fedconnector only.
Antenna consisting of brass and covered by afiberglass radome.
Length 2400 mm 94.5 in
Width 130 mm 5.1 in
Depth 245 mm 9.6 in4) Weight 22 kg 48.7 lbs
Wind AreaFore/Aft 0.31 m2 3.36 ft2
Side 0.56 m2 6.07 ft2
5) Rated Wind Velocity (Safety factor 2.0)>403 km/hr >250 mph
Wind Load @ 100 mph (161 km/hr)Fore/Aft 552 N 124 lbsSide 872 N 196 lbs
Vertically Polarized, Log Periodic 92° / 14.5 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
LPD-7905/8 __ 5°
Revision Date: 7/5/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-900 MHz
Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specifications
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).
Mounting bracket kit #36110003Downtilt bracket kit #36114002
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Frequency Range 806-900 MHz*
Impedance 50Ω3) Connector(s) NE or E-DIN
1 port / center1) VSWR ≤ 1.25:1
Polarization Vertical1) Gain 14.5 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 92°
E-Plane 7°1) Electrical Downtilt 5°1) Null Fill 5%
Lightning Protection Direct Ground
True log-periodic design allows for superiorfront-to-side characteristics to minimizesector overlap.
Durable brass feedline design eliminatesthe need for conventional solder joints inthe signal path.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
*Also available up to 960 MHz. Consult your salesdirector for more information. Antenna available with center-fed
connector only.
Antenna consisting of brass and covered by afiberglass radome.
Length 2400 mm 94.5 in
Width 130 mm 5.1 in
Depth 245 mm 9.6 in4) Weight 22 kg 48.7 lbs
Wind AreaFore/Aft 0.31 m2 3.36 ft2
Side 0.56 m2 6.07 ft2
5) Rated Wind Velocity (Safety factor 2.0)>403 km/hr >250 mph
Wind Load @ 100 mph (161 km/hr)Fore/Aft 552 N 124 lbsSide 872 N 196 lbs
Vertically Polarized, Log Periodic 102° / 10.5 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
LPD-7905/4/102 __
Revision Date: 7/5/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-941 MHz
Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specifications
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).
Mounting bracket kit #36110003Downtilt bracket kit #36114002
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Frequency Range 806-941 MHz*
Impedance 50Ω3) Connector(s) NE or E-DIN
1 port / center1) VSWR ≤ 1.25:1
Polarization Vertical1) Gain 10.5 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 102°
E-Plane 15°1) Electrical Downtilt 1.25°1) Null Fill 5%
Lightning Protection Direct Ground
True log-periodic design allows for superiorfront-to-side characteristics to minimizesector overlap.
Durable brass feedline design eliminatesthe need for conventional solder joints inthe signal path.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
*Also available up to 960 MHz. Consult your salesdirector for more information. Antenna available with center-fed
connector only.
Antenna consisting of brass and covered by afiberglass radome.
Length 1200 mm 47.2 in
Width 130 mm 5.1 in
Depth 245 mm 9.6 in4) Weight 10 kg 22.1 lbs
Wind AreaFore/Aft 0.16 m2 1.68 ft2
Side 0.27 m2 2.95 ft2
5) Rated Wind Velocity (Safety factor 2.0)>599 km/hr >372 mph
Wind Load @ 100 mph (161 km/hr)Fore/Aft 240 N 54 lbsSide 394 N 89 lbs
Vertically Polarized, Log Periodic 102° / 10.5 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
LPD-7905/4/102 __ 3°
Revision Date: 7/5/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-941 MHz
Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specifications
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).
Mounting bracket kit #36110003Downtilt bracket kit #36114002
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Frequency Range 806-941 MHz*
Impedance 50Ω3) Connector(s) NE or E-DIN
1 port / center1) VSWR ≤ 1.25:1
Polarization Vertical1) Gain 10.5 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 102°
E-Plane 15°1) Electrical Downtilt 3°1) Null Fill 5%
Lightning Protection Direct Ground
True log-periodic design allows for superiorfront-to-side characteristics to minimizesector overlap.
Durable brass feedline design eliminatesthe need for conventional solder joints inthe signal path.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
*Also available up to 960 MHz. Consult your salesdirector for more information. Antenna available with center-fed
connector only.
Antenna consisting of brass and covered by afiberglass radome.
Length 1200 mm 47.2 in
Width 130 mm 5.1 in
Depth 245 mm 9.6 in4) Weight 10 kg 22.1 lbs
Wind AreaFore/Aft 0.16 m2 1.68 ft2
Side 0.27 m2 2.95 ft2
5) Rated Wind Velocity (Safety factor 2.0)>599 km/hr >372 mph
Wind Load @ 100 mph (161 km/hr)Fore/Aft 240 N 54 lbsSide 394 N 89 lbs
Vertically Polarized, Log Periodic 102° / 10.5 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
LPD-7905/4/102 __ 5°
Revision Date: 7/5/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-900 MHz
Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specifications
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).
Mounting bracket kit #36110003Downtilt bracket kit #36114002
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Frequency Range 806-900 MHz*
Impedance 50Ω3) Connector(s) NE or E-DIN
1 port / center1) VSWR ≤ 1.25:1
Polarization Vertical1) Gain 10.5 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 102°
E-Plane 15°1) Electrical Downtilt 5°1) Null Fill 5%
Lightning Protection Direct Ground
True log-periodic design allows for superiorfront-to-side characteristics to minimizesector overlap.
Durable brass feedline design eliminatesthe need for conventional solder joints inthe signal path.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
*Also available up to 960 MHz. Consult your salesdirector for more information. Antenna available with center-fed
connector only.
Antenna consisting of brass and covered by afiberglass radome.
Length 1200 mm 47.2 in
Width 130 mm 5.1 in
Depth 245 mm 9.6 in4) Weight 10 kg 22.1 lbs
Wind AreaFore/Aft 0.16 m2 1.68 ft2
Side 0.27 m2 2.95 ft2
5) Rated Wind Velocity (Safety factor 2.0)>599 km/hr >372 mph
Wind Load @ 100 mph (161 km/hr)Fore/Aft 240 N 54 lbsSide 394 N 89 lbs
Vertically Polarized, Log Periodic 102° / 10.5 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
LPD-7905/4/102 __ 9°
Revision Date: 7/5/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-900 MHz
Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specifications
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).
Mounting bracket kit #36110003Downtilt bracket kit #36114002
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Frequency Range 806-900 MHz*
Impedance 50Ω3) Connector(s) NE or E-DIN
1 port / center1) VSWR ≤ 1.25:1
Polarization Vertical1) Gain 10.5 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 102°
E-Plane 15°1) Electrical Downtilt 9°1) Null Fill 5%
Lightning Protection Direct Ground
True log-periodic design allows for superiorfront-to-side characteristics to minimizesector overlap.
Durable brass feedline design eliminatesthe need for conventional solder joints inthe signal path.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
*Also available up to 960 MHz. Consult your salesdirector for more information. Antenna available with center-fed
connector only.
Antenna consisting of brass and covered by afiberglass radome.
Length 1200 mm 47.2 in
Width 130 mm 5.1 in
Depth 245 mm 9.6 in4) Weight 10 kg 22.1 lbs
Wind AreaFore/Aft 0.16 m2 1.68 ft2
Side 0.27 m2 2.95 ft2
5) Rated Wind Velocity (Safety factor 2.0)>599 km/hr >372 mph
Wind Load @ 100 mph (161 km/hr)Fore/Aft 240 N 54 lbsSide 394 N 89 lbs
Vertically Polarized, Log Periodic 102° / 13.5 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
LPD-7905/8/102 __
Revision Date: 7/5/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-941 MHz
Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specifications
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).
Mounting bracket kit #36110003Downtilt bracket kit #36114002
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Frequency Range 806-941 MHz*
Impedance 50Ω3) Connector(s) NE or E-DIN
1 port / center1) VSWR ≤ 1.25:1
Polarization Vertical1) Gain 13.5 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 102°
E-Plane 7°1) Electrical Downtilt 1.25°1) Null Fill 5%
Lightning Protection Direct Ground
True log-periodic design allows for superiorfront-to-side characteristics to minimizesector overlap.
Durable brass feedline design eliminatesthe need for conventional solder joints inthe signal path.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
*Also available up to 960 MHz. Consult your salesdirector for more information. Antenna available with center-fed
connector only.
Antenna consisting of brass and covered by afiberglass radome.
Length 2400 mm 94.5 in
Width 130 mm 5.1 in
Depth 245 mm 9.6 in4) Weight 22 kg 48.7 lbs
Wind AreaFore/Aft 0.31 m2 3.36 ft2
Side 0.56 m2 6.07 ft2
5) Rated Wind Velocity (Safety factor 2.0)>403 km/hr >250 mph
Wind Load @ 100 mph (161 km/hr)Fore/Aft 552 N 124 lbsSide 872 N 196 lbs
Vertically Polarized, Log Periodic 102° / 13.5 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
LPD-7905/8/102 __ 3°
Revision Date: 7/5/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-900 MHz
Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specifications
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).
Mounting bracket kit #36110003Downtilt bracket kit #36114002
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Frequency Range 806-900 MHz*
Impedance 50Ω3) Connector(s) NE or E-DIN
1 port / center1) VSWR ≤ 1.25:1
Polarization Vertical1) Gain 13.5 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 102°
E-Plane 7°1) Electrical Downtilt 3°1) Null Fill 5%
Lightning Protection Direct Ground
True log-periodic design allows for superiorfront-to-side characteristics to minimizesector overlap.
Durable brass feedline design eliminatesthe need for conventional solder joints inthe signal path.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
*Also available up to 960 MHz. Consult your salesdirector for more information. Antenna available with center-fed
connector only.
Antenna consisting of brass and covered by afiberglass radome.
Length 2400 mm 94.5 in
Width 130 mm 5.1 in
Depth 245 mm 9.6 in4) Weight 22 kg 48.7 lbs
Wind AreaFore/Aft 0.31 m2 3.36 ft2
Side 0.56 m2 6.07 ft2
5) Rated Wind Velocity (Safety factor 2.0)>403 km/hr >250 mph
Wind Load @ 100 mph (161 km/hr)Fore/Aft 552 N 124 lbsSide 872 N 196 lbs
Vertically Polarized, Log Periodic 102° / 13.5 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
LPD-7905/8/102 __ 5°
Revision Date: 7/5/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-900 MHz
Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specifications
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).
Mounting bracket kit #36110003Downtilt bracket kit #36114002
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Frequency Range 806-900 MHz*
Impedance 50Ω3) Connector(s) NE or E-DIN
1 port / center1) VSWR ≤ 1.25:1
Polarization Vertical1) Gain 13.5 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 102°
E-Plane 7°1) Electrical Downtilt 5°1) Null Fill 5%
Lightning Protection Direct Ground
True log-periodic design allows for superiorfront-to-side characteristics to minimizesector overlap.
Durable brass feedline design eliminatesthe need for conventional solder joints inthe signal path.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
*Also available up to 960 MHz. Consult your salesdirector for more information. Antenna available with center-fed
connector only.
Antenna consisting of brass and covered by afiberglass radome.
Length 2400 mm 94.5 in
Width 130 mm 5.1 in
Depth 245 mm 9.6 in4) Weight 22 kg 48.7 lbs
Wind AreaFore/Aft 0.31 m2 3.36 ft2
Side 0.56 m2 6.07 ft2
5) Rated Wind Velocity (Safety factor 2.0)>403 km/hr >250 mph
Wind Load @ 100 mph (161 km/hr)Fore/Aft 552 N 124 lbsSide 872 N 196 lbs
1300 Capital Drive Rockford, IL 61109 Toll-Free (888) 417-9562 Tel. (815) 399-0001 Fax. (815) 399-0156 Email: [email protected] www.antelinc.com
Mounting & Downtilt Bracket Kits
LPD Bracket Kits Part Number Bracket Type
36110002* Standard LPD Mounting Bracket Kit for: LPD-4013 LPD-7905 LPD-7905/2 LPD-7907 LPD-7907/2 LPD-7908 LPD-7908/2 36110003** Standard LPD Mounting Bracket Kit for: LPD-4016 LPD-4019 LPD-6513 LPD-6516 LPD-7905/4 LPD-7905/4/102 LPD-7905/8 LPD-7905/8/102 LPD-7907/4 LPD-7907/8 LPD-7908/4
Both the downtilt bracket kit and the standard mounting bracket kit must be
ordered for mechanical downtilt applications.
Mounting Bracket Kits are sold separately and not included in the price of antennas.
36110002* & 36110003** Top View
*Braket Kit: 36110002 contains two of pictured bracket. **Bracket Kit: 36110003 contains three of pic-tured bracket.
1300 Capital Drive Rockford, IL 61109 Toll-Free (888) 417-9562 Tel. (815) 399-0001 Fax. (815) 399-0156 Email: [email protected] www.antelinc.com
Mounting & Downtilt Bracket Kits
LPD Bracket Kits Part Number Bracket Type
36114001 Standard LPD *Downtilt Bracket Kit for: LPD-4013 LPD-7905 LPD-7905/2 LPD-7907 LPD-7907/2 LPD-7908 LPD-7908/2 36114002 Standard LPD *Downtilt Bracket Kit for: LPD-4016 LPD-4019 LPD-6513 LPD-6516 LPD-7905/4 LPD-7905/4/102 LPD-7905/8 LPD-7905/8/102 LPD-7907/4 LPD-7907/8 LPD-7908/4
*Both the downtilt bracket kit and the standard mounting bracket kit must be
ordered for mechanical downtilt applications.
Mounting Bracket Kits are sold separately and not included in the price of antennas.
36114001 Top View Side View
36114002 Top View Side View