lone wolf climber stands

8/4/2019 Lone Wolf Climber Stands

1/22

WARNING! Make sure you have read and understand all instructions.

Practice first at ground level.

Always wear TMA approved fall arrest system when usingany treestand.

Do not use while intoxicated or when taking medications that

cause drowsiness.

Do not attach to rotten, loose bark or dead trees, metal or

utility poles.

Avoid use during wet or icy conditions, or during lightning storms.

Haul gun or bow up from ground after climbing tree. Platform is designed to hold one person only.

Do notjump on platform or seat, nor should you stand on seat.

Do not attempt to alter product in any way.

Maximum load is 350 pounds, except where noted.

Failure to follow these instructions could cause serious injury or death.

WARNING!

You must read and understand all of the following instructions

before first use. If you do not, it could result in serious injury up

to and including death. Any questions please call 309-691-9653.

ALWAYS WEAR A TMA APPROVED FALL ARREST

SYSTEM WHEN USING ANY TREESTAND

If you do not understand any of these instructions,

please call Customer Service (309-691-9653) or

visit our web site (www.lonewolfstands.com)


2/22

LONE WOLF PORTABLE TREESTANDSPO Box 62

Edwards, IL 61528Phone: (309) 691-9653 Fax: (309) 693-9410

www.lonewolfstands.com

PRODUCT LINE

INSTRUCTIONSMANUAL


3/22

1



Always wear TMA approved fall arrest system when usingany treestand.

Do not use while intoxicated or when taking medications that

cause drowsiness.

Do not attach to rotten, loose bark or dead trees, metal or

utility poles.

Avoid use during wet or icy conditions, or during lightning storms.

Haul gun or bow up from ground after climbing tree. Platform is designed to hold one person only.





WARNING!

You must read and understand all of the following instructions

before first use. If you do not, it could result in serious injury up

to and including death. Any questions please call 309-691-9653.







4/22

3

Make sure all nuts and bolts are secure before each use.

Replace any worn or damaged parts with components from Lone Wolf.

All bolts for this product are Grade 8.

POLYURETHANE TRACTION BELT

APPLICABLE TO: Alpha Sit & Climb and Alpha Hand Climber

1.) With a permanent marker write date of 1st use on each belt.

2.) Inspect belt before each use

3.) Replace every 5 years or when you observe any of the following:

a.) belt has external cracks or tears visible

b.) any internal cables are broken

c.) any teeth are offset from normal pitch or are torn or cut

Shown is the proper use of the traction

belt for the Lone Wolf Climbers (dia 1). The

polyurethane belts are designed to be used

on the Lone Wolf products only. Always use

your traction in the position that it is shown in

dia 1. Never use the belt in this position (dia. 2).

Use in this position can cause damage to the

traction belt. WARNING: Point of arrow marks

the end of the belt (dia. 2a). No part of the

arrow should be showing after the cams are

engaged (dia. 1a). Any failure to follow the

instructions may cause belt to disengage

and cam to open.

General Maintenance

POLYESTER WEB BELTS

APPLICABLE TO: Alpha Ladder Stand, Climbing Sticks, Elite Hang on, Alpha Hang On,

Assault Hang On, and Assassin Platform, Pro Series Hang On & Climbing Sticks

1.) Inspect belts before each use

2.) Replace every 5 years or every year if left out yearly

3.) Replace belts if you observe any of the following:a.) cut or worn webbing

b.) buckles are bent or cam release is binding

c.) stitching is loose, cut, or becoming unraveled

4.) With a permanent marker write the date of the 1st use on each belt

CORRECT INCORRECT

CORRECT INCORRECT

(dia. 1) (dia. 2)

(dia. 1a) (dia. 2a)


5/22

27






Lone Wolf Climbing Stands

(Applicable to the Alpha Hand Climber and Alpha Sit and Climb.Includes: Back Packing straps, Seat Cushion, Bungee Cord,

Stabilizer Straps and 6-Pt Fall Arrest System.)



Always wear TMA approved fall arrest system when using any treestand.

Do not use while intoxicated or when taking medications that cause drowsiness.

Do not attach

to rotten, loose bark or dead trees, metal or utility poles. Avoid use during wet or icy conditions, or during lightning storms.

Haul gun or bow up from ground after climbing tree.

Platform is designed to hold one person only.





GENERAL MAINTENANCE

Make sure all nuts and bolts are secure before each use.

Replace any worn or damaged parts with components from Lone Wolf.

All bolts for this product are Grade 8.

POLYURETHANE TRACTION BELT

Replace every 5 years. Inspect belts before each use.

Replace belts when you observe any of the following:

a.) Belt has external cracks or tears visible.

b.) Any internal cables are broken.

c.) Any teeth are offset from normal pitch, or are torn or cut.

d.) With permanent markers write date of first use on each belt.


6/22

28






continued

ALPHA HAND CLIMBER (HCCSH) ALPHA SIT & CLIMB (SACCSH)


POLYURETHANE TRACTION BELT continued

1.) With a permanent marker write date of 1st use on each belt.2.) Inspect belt before each use3.) Replace every 5 years or when you observe any of the following:

a.) belt has external cracks or tears visibleb.) any internal cables are brokenc.) any teeth are offset from normal pitch or are torn or cut

Shown is the proper use of the traction

belt for the Lone Wolf Climbers (dia 1). The

polyurethane belts are designed to be usedon the Lone Wolf products only. Always use

your traction in the position that it is shown in

dia 1. Never use the belt in this position (dia. 2).

Use in this position can cause damage to the

traction belt. WARNING: Point of arrow marks

the end of the belt (dia. 2a). No part of the

arrow should be showing after the cams are

engaged (dia. 1a). Any failure to follow theinstructions may cause belt

to disengage and

cam to open.

CORRECT INCORRECT

CORRECT INCORRECT

(dia. 1) (dia. 2)

(dia. 1a) (dia. 2a)


7/22

29






Step 3: Pull the cord to the end of the slot.

Cam Tethers

Step 1: Run the tether through the hole

in the end of the cam.

Step 2: Tie the ends together.

continued



8/22

30






Stabilizer Strap InstallationClimber SeatAlpha Hand Climber and Alpha Sit and Climb.

Step 1: For the HAND CLIMBER TOP

SECTION take the short end of the sta-

bilizer straps and take it over the casting

in the front corner of the seat through the

sewn loop.

Step 2: Pull tight.

Step 1: For the SIT AND CLIMB TOP

SECTION, wrap the short end of the

strap under the angled support arm at

the location shown. Make sure the sewn

loop is to the outside.

Step 2: Thread the buckle in through

the sewn loop and cinch it up tight.

Rotate the stabilizer buckle so it points

downward.

continued



9/22

31






Step 1: To install the straps on the

STAND BASE thread the long end of the

strap long end of the strap along the

edge frame of the casting just in front of

the brush pocket towards the rear.

Step 2: Run the sewn loop through and

pull tight.

Stabilizer Strap InstallationClimber BaseApplicable to Alpha Hand Climber and Alpha Sit and Climb.

continued



10/22

32






Step 2: Then, push the hinge forward

to the end of the slot.

First, install the climber base.

Step 1: Loosen the torque knobs and

pull the hinge washer inward.

Step 3: Re-tighten the knobs.

Lone Wolf Climber PLATFORM InstallationApplicable to Alpha Hand Climber and Alpha Sit and Climb.

continued



11/22

33






Step 6: Place around the tree. Adjust

the stand platform slightly higher on thefront end.

Step 5: Pull the belt from the tube.

Step 7: Insert the belt back into the

tube. NOTE: WARNING- point of arrowmarks the end of the belt. No part of the

arrow should be showing after the cams

are engaged. Failure to follow these

instructions could cause belt to disengage

and cam to open. Now re-attach the

cams firmly.

Step 4: Unlatch the cam.

continued


Lone Wolf Climber PLATFORM Installation continuedApplicable to Alpha Hand Climber and Alpha Sit and Climb.


12/22

34






Lone Wolf Climber TOP SECTION InstallationApplicable to Alpha Hand Climber and Alpha Sit and Climb.

Step 1A: For the HAND CLIMBER flip

the tubes over so they rest on the side of

the seat casting.

Step 1B: For the SIT AND CLIMB,

loosen the torque knobs.

Step 2: Pull the hinge washer inward. Step 3: Push the hinge forward to the

end of the slot.

continued



13/22

35






Step 4: Retighten the knobs. Now, you

are ready to put your top section onto

the tree.

Step 5: Unlatch the cam and pull the

belt from the tube.

Step 6: Place the belt around the tree and insert into the tube.

NOTE: WARNING- Point of arrow marks the end of the belt. No part of the arrow

should be showing after the cams are engaged. Failure to follow the instructions

may cause belt to disengage and cam to open.

Lone Wolf Climber TOP SECTION Installation continuedApplicable to Alpha Hand Climber and Alpha Sit and Climb.

continued



14/22

36






Step 7: Now re-attach your cam firmly. Step 8: Connect your stabilizer straps.

WARNING- the stabilizer straps must be

connected before leaving the ground and

must always remain connected while the

treestand is in use.

Lone Wolf Climber TOP SECTION Installation continuedApplicable to Alpha Hand Climber and Alpha Sit and Climb.

continued



15/22

37






Climbing Instructions Alpha Hand Climber

Step 1: Harness to tree. Step 2: Support your weight onto the

climbing aid.

Step 3: Place your feet under the

hinges and the bar as shown. Apply

slight pressure to the hinge with the

inside of the foot.

Step 4: Bend at the knees to

disengage stand.

continued



16/22

Step 5: Keeping one foot under the

hinge bar, step back onto the center of

the stand with the other to secure it in

place.

Step 6: Slide the harness rope up the

tree to the appropriate height.

38






Step 5: Keeping one foot under the

hinge bar, step back onto the center of

the stand with the other to secure it in

place.

Step 6: Slide the harness rope up the

tree to the appropriate height.

Step 7: Disengage the climbing aid,

raise, and repeat the process.

Step 8: When you reach your desiredheight or when the platform becomes

level, adjust your harness rope height

to it is tight while in a sitting position.

Now while in a sitting position pull your

stabilizing straps tight.

Climbing Instructions Alpha Hand Climber continued

continued



17/22

39











Climbing Instructions Alpha Sit & Climb

Step 1: Step into center of from. Attach

harness rope to tree and lift into postion

to climb.

Step 2: Distribute your weight onto

climbing aid. Place feet under hinge and

bar as shown. NOTE: Flip foam seat pad

over one time, this will hold the seat in

upright position.

Step 3: Apply slight pressure to hinge

with inside of foot. Bend at knees to

disengage stand.

Step 4: Pull stand up with legs. Re-

engage stand by shifting weight to heels.

Slide harness rope up tree to appropriate

height. Stand up and repeat process.

continued



18/22

40






Step 1: Fold the stand and seat down

flat placing the two bolt heads into the

stabilizer channel as shown.

Step 2: Lay the top section of the Hand

Climber on top of the platform.

Step 3: Install the bungee cord and stabilizer straps as shown.

Alpha Hand Climber Back Packing Instructions

continued



19/22

41






Step 4: Criss cross stab straps. Step 5: This is the proper position for

the Hand Climber to be back packed.

Alpha Hand Climber Back Packing Instructions continued

continued



20/22

42






Step 1: The traction belts should be

retracted into the tubes as far as possi-

ble with the cams in the locked position.

Step 2: Fold the top and bottom flat

and place the top upside down.

Step 3: Place the Sit and Climb bar

between the teeth and traction belt.

Step 4: Lay the bar on 2 points of the

teeth.

Alpha Sit and Climb Back Packing Instructions

continued



21/22

43






Step 8: This is the proper position for

back packing the Sit and Climb.

Step 5: Install the bungee cord and

stabilizer straps as shown.

Step 7: Criss-cross and connect the

stabilizer straps. Pull them tight.

Alpha Sit and Climb Back Packing Instructions continued

continued



22/22

62

For written and video instructions

please visit www.lonewolfstands.com

See the latest from Lone Wolf

at www.lonewolfstands.com

The Wolf PackLone Wolf Quiver and

Quiver Stand Mount

Wolf Jaws Combo Silent Tote

lone wolf climber stands

Documents