louvers catalog

Louver Products

w w w . e h p r i c e s a l e s . c o mJ a n u a r y 2 0 0 6 B-1.0

© Copyright E.H. Price Limited 2006. All Metric dimensions ( ) are soft conversion. Imperial dimensions are converted to metric and rounded to the nearest millimetre. EG-�

Louvers Engineering Guide

LOU

VE

RS

Index

Extruded Aluminum

Selecting the Right Louver ...................................... EG2 - EG3

Field Measurement Information ............................. EG4 - EG9

How to use the Price Nomographs .....................EG�0 - EG��

AB

C

E

D

F

G

X

Y

WB

90˚

HR

DRDL

HL

WT

AB

A

D

C

E

B

F

W

G H

EG-2 All Metric dimensions ( ) are soft conversion. © Copyright E.H. Price Limited 2006. Imperial dimensions are converted to metric and rounded to the nearest millimetre.

Louvers Engineering GuideLO

UV

ER

S

Selecting the right louver

When selecting a louver, there are sev-eral factors that should be considered:a) Architectural considerationsb) Locationc) Performance

a) Architectural considerations: Louvers can be built in multiple sec-tions with visible mullions both verti-cally and/or horizontally or they can be built in a continuous blade method (CB) offering an uninterrupted blade line. They can also be built into a pent-house with mitered or box corners.

b) Location: When louvers or penthouses are

installed at ground level where they can be subject to physical abuse, consideration should be given to their structural strength. In these cases, steel or heavy 8 ga. aluminium construction should be considered.

c) Performance: When discussing performance, four

major topics must be considered:

First consideration: FREE AREA• The minimum area through which air

can pass within a louver is called the free area of a louver1.

• The free area of a louver is critical to its overall performance and must be considered during its selection process.

• The free area has a direct effect on the air velocity though the louver: less free area creates higher air velocities thus a higher pressure drop. For intake conditions, higher air velocities equal higher water penetration.

• Everything being relative, this is true for all types and models of louvers.

• Whenever free area percentages are used always state the louver size on which it was calculated. (Published free area data is based on 48” X 48” louver)

Although it is evident that free area varies with louver size, when a louver is selected for a low height application, the free area drops much faster than expected. This effect is most drastic as

the louver height approaches 3 to 4 times the louver depth. Since the head and sill of a louver are of a fixed height, the space they occupy becomes important, thus reducing considerably the amount of available blade face area (and thus free area). As an example, a 48” x 48” x 4” deep louver may have 8.8 sq.ft. of free area (55%), a 48” x 12” of the same model would have 1.5 sq.ft. (37%). As a general rule, avoid selecting a louver when its height is less than 4 times its depth. The actual free area should always be checked when designing a louver below 48” in height. When the louver height exceeds 48”, the percent-age of free area will increase slightly.

1 AMCA PUBLICATION 501-93, Applica-tion Manual for Air Louvers

© Copyright E.H. Price Limited 2006. All Metric dimensions ( ) are soft conversion. Imperial dimensions are converted to metric and rounded to the nearest millimetre. EG-3


LOU

VE

RS

Second consideration:WATER PENETRATION

• Although water penetration data is published based on the AMCA Stan-dard 500 test method, its primary use is for comparison purposes between models and suppliers and of limited use in the design process since wind driven rain is not included.

• No accurate method exists at this time to design and select an intake louver based on water penetration.

• Experience has shown that selecting an intake louver with a reasonable margin of safety below the Beginning Point of water penetration (as defined by the AMCA Standard 500L) will avoid significant water penetration under severe storm conditions.

• Water penetration is not considered on exhaust louvers; the selection is usually based on the permissible pres-sure drop.

• It must be recognized that all louvers (intake and exhaust) will permit some degree of water penetration when exposed to wind driven rain. Floor drains should be provided in the plenum behind the louver.

• A new test method that includes wind driven rain was being released by AMCA in 1999 (AMCA Standard 500L-1999).

• At this time, no test data exists on snow penetration through louvers.

Selecting the right louver (cont'd)

Third consideration:PRESSURE DROP

• The sizing of a louver for a desired pres-sure drop and air flow rate is greatly simplified with the unique PRICE NOMOGRAPHS: refer to the appro-priate sheet and “How to use PRICE NOMOGRAPHS” for details (see page AA-11). They also permit quick selection based on free area and airflow rate or louver dimensions and free area velocity or any other combination of parameters as a starting point. PRICE NOMOGRAPHS have been prepared for fixed blade, adjustable blade and acoustic louvers and penthouses.

• When installing a damper behind a fixed louver, the total pressure drop can be unpredictable. Use a louver with an integrated damper (combination louver) which is built as a single unit, the performance is tested and predict-able.

• The pressure drop curves of louvers are based on free area velocity and vary very little, depending almost exclu-sively on the shape of the air passage between the blades.

• Screens can add a pressure drop increase of up to 10%.

• Fine mesh screens (insect screens) should always be made easily remov-able and installed only during critical periods. They must be cleaned regularly to remove dirt and debris.

Fourth consideration:WIND LOADS and STRUCTURAL ELEMENTS• As a standard, all PRICE louvers built

in a single section are designed to sup-port a 25 psf (100 mph) wind load.

• All louvers having 2 sections in width by 2 sections in height or more may require additional structure to support the wind load.

• Louvers greater than 72” in width by 2 sections in height or more may require additional structure to support the wind load.

• Splice angles used to join sections in height are for alignment purposes only and cannot be considered structural elements.

• Since louver blades are welded to the jambs, securing a louver section by its jambs and central blade support, (if used) is considered acceptable practice.

General Selection Guidelines

Note for louvers in multiple sections:Louvers built in multiple sections are designed with provisions for thermal expansion and when installed, should never be butted together. When the temperature varies between -35°C to 40°C, the thermal expansion of a 10 ft [3m] aluminium louver is almost ¼” [6mm] (steel louvers expand half this amount).

EG-4 All Metric dimensions ( ) are soft conversion. © Copyright E.H. Price Limited 2006. Imperial dimensions are converted to metric and rounded to the nearest millimetre.


UV

ER

S

Once the louvers have been approved by the architect, the louvers can be re-leased for production. Before you can proceed, the opening dimensions must be confirmed. The next step is critical in ensuring that the louver installation will go smoothly: you must make field meas-urements of the opening and record the job site conditions and any obstructions. Improper information at this point or neglecting to check all the job conditions can have dire consequences later.

For this reason PRICE has developed a step by step method to assist you in completing this essential task.

Basic principle: The basis of precise field measurements is the use of the principle of triangulation. Once you know the lengths of the three sides of a triangle, that triangle is unique and fully defined. The angles at the corners are no longer required. Thus any shape can be sub-divided into a series of triangles and be precisely defined with the dimensions of their sides.

Step �. Study the architectural drawings and approved submittal drawings to fully understand how the louvers are intended to be installed on the project, how they are to fit in the openings and how they are to be attached in those openings.

Step 2. You can now proceed with the opening measurements. Prepare a sketch of each louver viewed from the exterior and identify its location.

AB

BOTTOM BOW

LEFT SIDE BOW

Step #3a: Measure the opening width and height on all 4 sides.

Step #3b: Measure the diagonal distances between opposite corners.

Step #3c: Use a string to see if the sides of the opening bows in or out. If an inward bow is detected, rectify it if possible. For those that cannot be rectified, record them on your sketch.

Field Measurement Information

W BOTTOM

W TOP

H LEFT H RIGHT

Step 3. Square and Rectangular Louvers



LOU

VE

RS

Step 4. Right Angle Triangular Louvers

Step #4a: Measure the opening width, height and diagonal side. Based on these dimensions, louver dimensions will be corrected to obtain 90° between width and height.

Exterior Elevation

Step #4b: Use a string to see if the sides of the opening bows in or out. If an inward bow is detected, rec-tify if possible. For those that cannot be rectified, record them on your sketch.

D

W

H

90˚ W BOW

D BOW

Step #�a: Measure the 3 sides of the opening.

Note: Dim. A and C are not necessarily equal.

ExteriorElevation

B

A C

B BOW

C BOW

Field Measurement Information (cont'd)

Step �. Common Triangular Louvers

Step #�b: Use a string to see if the sides of the opening bows in or out. If an inward bow is detected, rec-tify if possible. For those that cannot be rectified, record them on your sketch.

EG-� All Metric dimensions ( ) are soft conversion. © Copyright E.H. Price Limited 2006. Imperial dimensions are converted to metric and rounded to the nearest millimetre.


UV

ER

S

Step �. Circular, Semicircular and Ogive Shaped Louvers

Exterior Elevations

B

A

C

C

F

B

E

D I

H

G

A

For openings of 72" [1829] or less.

Note: Dimensions D through I should be approximately equal to the radius of the circle.

For openings larger than 72" [1829].

Step #�a: If the circular opening is relatively small and has a consistent circumference, you can mea-sure the diameter in 3 or 4 locations and record the smallest dimension. For larger or irregular openings, mark the circular opening in 6 approximately equidistant points on the edge of the opening. Measure the distances A, B, C and the actual distances D through I. By the use of computer assisted drafting (CAD), a true circle will be fitted to the actual opening.

Exterior Elevations

Step #�b: Mark the circular portion of the opening in 4 approximately equidistant points on its edge opening. Measure the distances A, B, G, H, W and the actual distances C through F. By the use of computer assisted drafting (CAD), a true circular portion will be fitted to the actual opening.

A

D

C

E

B

F

W

G H

W

B

E

C

A

D

FG H


Step #�c: Use a string to see if the base of the opening bows in or out. If an inward bow is detected, rectify it if possible. If it cannot be rectified, record it on your sketch.



LOU

VE

RS

Step �. Louvers Shapes with 2 Vertical Parallel Sides

Step #�a: Divide opening into rectangles and triangles and treat as in Steps #3a through 5b. Based on these dimensions, louver dimensions will be corrected to obtain parallel sides and/or 90° between width and height.

WB

90˚

HR

DRDL

HL

WT

AB

HR

HL

90˚

W

D

A

B

B

A

HL

HR

DT

DB D

W

A

B

HL

HR

Exterior Elevations


Step #�b: Use a string to see if the base of the opening bows in or out. If an inward bow is detected, rectify it if possible. If it cannot be rectified, record it on your sketch.

EG-� All Metric dimensions ( ) are soft conversion. © Copyright E.H. Price Limited 2006. Imperial dimensions are converted to metric and rounded to the nearest millimetre.


UV

ER

S

Large shapes divided into sectionsWhen a louver shape is divided into sections by visible mullions or when various louver shapes are interdependent and if the blades must line up in the final assembly, always include a sketch of the relative positions of the individual shapes.

X Y

Section A Section B Section C


Step �. Irregular Shaped Louvers

Step #�a: After measuring the 3 sides of the opening, draw a horizontal line to establish the blade orientation and measure distance X and Y.

Step #8b: Measure the d is tances A through E . Divide shape into simple triangular shapes and measure the remaining distances F and G. Draw a horizontal line to establish the blade orientation and measure distances X and Y.

C

A

B

X

Y

AB

C

E

D

F

G

X

Y

Exterior Elevations

Step #8c: Use a string to see if the base of the opening bows in or out. If an inward bow is detected, rectify it if possible. If it cannot be rectified, record it on your sketch.

© Copyright E.H. Price Limited 2006. All Metric dimensions ( ) are soft conversion. Imperial dimensions are converted to metric and rounded to the nearest millimetre. EG-9


LOU

VE

RS

Sill Extension or Loose SillsLoose sills or sill extensions are used to deflect rain water away from the sill of the louver towards the exterior of the building. They are designed to maintain a continuous watertight ledge under the louver extending downwards from its backside towards the exterior finished wall. To establish its proper size, measure the distance between the proposed location of the louver face to the finished face of the building, add the overall louver depth plus ¼” [6mm]. In some cases, sill extensions may be shipped in sections; always give the opening width so that suf-ficient overlap can be allowed for.

Louvers in Multiple SectionsLouvers built in multiple sections are designed with provisions for thermal expansion and when installed, should never be butted together. When the temperature varies between -35ºC and 40ºC, the thermal expansion of a 10 ft [3m] aluminum louver is almost ¼” [6mm] (steel louvers expand half this amount).


Louver UndersizingAllowance must always be made in the final sizing of the louver to compensate for the irregularities in the sides of the opening, thermal expansion and caulking. By always giving the actual opening dimensions with a clear indication of nonlinear conditions on the opening edges, proper undersizing can be achieved. This is especially true for louver shapes.

As a standard practice, PRICE will manufac-ture the louvers with a minimum ¼” (6mm) gap all around. If a different gap is preferred be sure to indicate it on your order.

Thus, for a 48" by 48" opening without exces-sive bowing of the sides of the opening, the actual louver size, as manufactured, would be 47.5" by 47.5".

Louver FlangesAlthough flanges of various widths are available, the most common flange is 1½”(38mm). The flange width is defined as the width that exceeds the louver frame. Thus, the overall size of a louver with 1½” flanges to fit a 48" x 48" opening would be 50½” by 50½” and would exceed the opening by 1¼”.

48" x 48" opening less undersizing (2 x ¼”) = 47½” x 47½” louver with flanges added (2 x 1½”) = 50½” x 50½” overall

Structural SupportWhen the louver comes in several sections, structural supports must be provided to securely attach these sections to the build-ing. In most cases, these structural elements are installed ahead of time by others and their exact location “as installed” must be verified to ensure that their location matches the louver submittal drawings. If required, changes can be made to relocate the mul-lions on the louvers before they are put into production with little or no cost.

Here are other questions which may have to be addressed:

Is there adequate space behind the louver to permit fastening from inside?Are there any structural or other ele-ments that might interfere with the louver?Are the vertical edges of the opening sufficiently rigid to attach the sides of the louver?

StandardInstallation

Continuous BladeInstallation

EG-�0 All Metric dimensions ( ) are soft conversion. © Copyright E.H. Price Limited 2006. Imperial dimensions are converted to metric and rounded to the nearest millimetre.


UV

ER

S

How to use the Price Nomographs

PRICE has developed this unique graphi-cal tool to help you select PRICE louvers without the use of a calculator.

All you need is a ruler and a pencil. A multitude of “what if” conditions can be quickly evaluated and the working copy of the nomograph can be retained for future reference.

Step �. To use the PRICE Nomographs, you need to know at least 3 of the following 6 variables: the louver width and height, the louver free area, the air volume, free area air velocity or static pressure loss. The possible starting point combinations are as follows:One louver dimension – flow rate – free area velocityOne louver dimension – flow rate – pres-sure dropOne louver dimension – flow rate – free areaTwo louver dimensions – flow rateTwo louver dimensions – pressure drop

Two louver dimensions – free area velocity

Step 2. The PRICE Nomograph is com-prised of 2 interrelated areas. The dimen-sional characteristics are on the left side of the sheet and the air flow characteristics are on the right. Drawing a line joining the “Louver Width” (W scale) to the “Louver Height” (H scale), you obtain the free area as the line crosses the “Louver Free Area” (A scale). You can also start with the free area and one dimension to obtain the 2nd dimension.

Step 3. Drawing a second line joining the “Louver Free Area” (A scale) (obtained in step 2) to the “Louver Air Flow” (F scale), you obtain the free area velocity and pressure drop as the line crosses the “Pressure drop / Free area velocity” (P-V scale). The line can also be drawn with any combination of 2 starting points: [free area & pressure drop] or [flow rate & pressure drop] or [flow rate & free area velocity].

The PRICE Nomographs give you maximum flexibility in the selection of your PRICE louvers.

See the examples on the following page for more details.

W = Louver Width (inches)H = Louver Height (inches)A = Louver Free Area (Square feet)F = Air Flow (CFM)P-V = Static Pressure Drop (in. of Water) Free Area Air Velocity (FPM)

Legend

W

A

H

P-V

F

W = Louver Width (inches)H = Louver Height (inches)A = Louver Free Area (Square feet)F = Air Flow (CFM)P-V = Static Pressure Drop (in. of Water) Free Area Air Velocity (FPM)

Legend

W

A

H

P-V

F

© Copyright E.H. Price Limited 2006. All Metric dimensions ( ) are soft conversion. Imperial dimensions are converted to metric and rounded to the nearest millimetre. EG-��


LOU

VE

RS

EXAMPLES:

�. The louver size is 36” wide by 72” high and the required intake air volume is 6,000 CFM. What is the free area, the pressure drop and the free area velocity?

a). Draw a line joining 36” wide on the “Louver Width” (W scale) to 72” high on the “Louver Height” (H scale).

b). Read the free area at the point where the line meets the “Louver Free Area” (A scale).

ANSWER The louver free area is 10.02 square feet.

c). Draw a line joining 6,000 CFM on the “Air Flow” (F scale) to the free area you just found.

d). Read the free area velocity and static pres-sure loss at the point where this second line meets the “Pressure Drop/Free Area Velocity” (P-V scale).

ANSWER The free area air velocity is 600 FPM and louver static pressure loss is 0.06”.

2. The louver exhaust air volume is 6,000 CFM and expected static pres-sure loss is 0.06”. Louver height must be smaller or equal to 72”.What is the required free area and minimum louver width?

a). Apply pressure drop correction factor for exhaust condition 0.06" ÷ 0.825 = 0.07" WG

b). Draw a line joining 6,000 CFM on the “Air Flow” (F scale) to the calculated static pressure loss on the “Pressure Drop/Free Air Velocity” (P-V scale) and continuing to the “Louver Free Area” (A scale).

c). Read the free area at the point where the line meets the “Louver Free Area” (A scale).

ANSWER The louver free area is 10.02 square feet.

d). Draw a line joining the 72” high on the “Louver Height” (H scale) to the free area and continuing to the “Louver Width” (W scale).

e). Read the required louver width.

ANSWER The minimum louver width is 36”.

How to Use the Price Nomographs (cont'd)

For example purposes only.

© Copyright E.H. Price Limited 2010. All Metric dimensions ( ) are soft conversion. Imperial dimensions are converted to metric and rounded to the nearest millimetre. 1

LOU

VE

RS

LouversIndex

Extruded Aluminum

JE443 Stationary Louvers .................................................. L3

ZE439 Stationary Louvers .................................................. L4

ZE445 Stationary Louvers .................................................. L5

DE439 Stationary Drainable Louvers ................................. L6

DE635 Stationary Drainable Louvers ................................. L7

NJE2 Stationary Louvers .................................................. L8

NSE1 Stationary Louvers .................................................. L9

QA645 Stationary Acoustic Louvers ................................ L10

QA1245 Stationary Acoustic Louvers ................................. L11

RSE5 Rain Storm Louvers .............................................. L12

MCJE443 Miter Corner Penthouse Stationary Louvers ...... L13

MCZE439 Miter Corner Penthouse Stationary Louvers ...... L14

MCZE445 Miter Corner Penthouse Stationary Louvers ...... L15

MCDE439 Miter Corner Penthouse Stationary Louvers ...... L16

MCDE635 Miter Corner Penthouse Stationary Louvers ...... L17

BCJE443 Box Corner Penthouse Drainable Louvers ........... L18

BCZE439 Box Corner Penthouse Drainable Louvers .......... L19

BCZE445 Box Corner Penthouse Drainable Louvers .......... L20

BCDE439 Box Corner Penthouse Drainable Louvers .......... L21

BCDE635 Box Corner Penthouse Drainable Louvers .......... L22

Accessories ................................................................................ L23

Suggested Specifications ............................................. L24 - L31

Price / Airolite Cross Reference ............................................ L32

All Metric dimensions ( ) are soft conversion. © Copyright E.H. Price Limited 2010. Imperial dimensions are converted to metric and rounded to the nearest millimetre. 2

LOU

VE

RS

The founding principles of Price have never changed - business integrity, first class service and a commitment to people. Our dependable quality, reliable delivery and knowledgeable follow-up service have made us a market leader in supplying air distribution products and related equipment. As a result of our aggressive research initiatives combined with our continuous improvement practices we are now able to offer a complete and comprehensive line of louver products. Designed and engineered to meet the most demanding applications and specifications. Price’s new louvers offering are designed to be architecturally appealing while providing superior performance.

Features and Benefits of Price Louvers:• All welded construction ensures that the

louver can withstand the most severe weather conditions while maintaining functionality.

• Wide selection of blade styles to meetall demanding architectural and perfor-mance specifications.

• Extrudedaluminumbladesand framesprovide exceptional durability.

• FinishedtoPricestandards.

General Product Overview

Louver Selection Guide

Louvers

Available With Water Visible Concealed Louver Blade Frame Free Area Penetration Mullion Mullion Depth Thickness Thickness (4' x 4' Unit) Rating Storm Class Louver RSE5 Yes 5" (127 mm) 0.081" (2 mm) 0.081" (2 mm) 39% 99.73% Effective Extruded Aluminum Architecural JE443 Yes 4" (102 mm) 0.081" (2 mm) 0.081" (2 mm) 51% 5,200 CFM (147 m3/min) ZE439 Yes 4" (102 mm) 0.081" (2 mm) 0.081" (2 mm) 52% 7,059 CFM (200 m3/min) ZE445 Yes 4" (102 mm) 0.081" (2 mm) 0.081" (2 mm) 50% 5,298 CFM (150 m3/min) Extruded Aluminum Drainable DE439 Yes 4" (102 mm) 0.081" (2 mm) 0.081" (2 mm) 54% 7,589 CFM (215 m3/min) DE635 Yes 6" (152 mm) 0.081" (2 mm) 0.081" (2 mm) 56% 9,316 CFM (264 m3/min) Acoustic QA645 No 6" (152 mm) 0.081" (2 mm) 0.081" (2 mm) 29% 780 CFM (22 m3/min) QA1245 No 12" (305 mm) 0.081" (2 mm) 0.081" (2 mm) 25% 1,046 CFM (30 m3/min) Extruded Aluminum Narrow Profile NSE1 No 1.5" (38 mm) 0.125" (3 mm) 0.064" (1.6 mm) 69% N/A NJE2 No 2" (51 mm) 0.064" (1.6 mm) 0.064" (1.6 mm) 44% 380 CFM (11 m3/min)


LOU

VE

RS

Product Information

Extruded AluminumJE443

Models

Blade Louvers 43° J-Blade JE443

Price JE443 stationary louvers feature alloy 6063-T5 extruded aluminum blades. The louver features a “J” blade profile in a 4” deep assembly with the blades positioned at a 43° angle. This J-blade louver is available with visible mullions that are joined with an extruded aluminum “I” connection, or continuous horizontal blades that utilize concealed blade braces and hidden vertical supports in place of jamb frames to present uninterrupted horizontal blade appearance.

Performances of louvers manufactured by Price are based on tests and procedures in accordance with AMCA Publication 511 and comply with the requirements of the AMCA Certified Rating Program.Features• "J" Blade Profile.• .081” Extruded Aluminum Blades and

Frames.• Nominal 50.6% free area (based on 48”x

48”).• Integral perimeter caulking stop.• 1/2" x 1/2" (12 x 12) 16 gauge Expanded

Aluminum Bird Screen without frame.• Mill finish.

Options• WeldedConstruction.• Extended Sill (loose) 14 GA. Aluminum.• Continuous Blade Sections (invisible

mullions).• Blank-offs are available in Aluminum

with or without Insulation. Insulation is available in 1”, 1.5”, 2”, or 3” thickness.

• Variety of Mounting options.• ExteriororInteriorFrameMounting.• Variety of Bird Screens, Insect Screens

andFramesavailable.• WidevarietyofFinishes:BakedEnamel,

Prime Coat, Custom Finishes, ClearAnodized and Colour Anodized.

• Select from PRICE Colour Chart or provide colour sample to match.

• Note:Colourvariationscanbeexpectedwithin the same order and even on the same louver due to the anodizing process.

Blade Louvers4" (102 mm) Deep

(1) Beginning point of water penetration is defined by AMCA standard 511 as the free area velocity at which 0.01 ounces of water per square foot of free area is measured to pass through a 4' x 4' louver during a 15 minute test.

JE443

Louver Type Visible Mullion or Continuous Blade

Material Extruded Aluminum (Alloy 6063-T5)

Stationary Blade .081” (2 mm)

Frame .081” (2 mm)

Louver Depth 4” (102 mm)

Blade Angle 43o

Performance Rating AMCA Standard Standard 500

Wind Load 25 psf (100 mph)

Free Area – 8.1 sq.ft. 4’ x 4’ Unit (0.753 sq.m.)

Percent Free Area 50.6%

Free Area Velocity at Beginning Point of 642 FPM Water Penetration (1) (196 m/min)

Air Volume Delivered at Beginning Point of 5,200 CFM Water Penetration (1) (147 m3/min)

Pressure Drop at Beginning Point of 0.07” H2OWater Penetration (1) (18 Pa)

Product Information IndexAccessories ...............................................L23Suggested Specification ..........................L24

®

E.H. Price Limited certifies that the JE443 shown herein is licensed to bear the AMCA Seal. The ratings shown are based on tests and procedures performed in accor-dance with AMCA Publication 511 and comply with the requirements of the AMCA Certified Ratings Program The AMCA Certified Seal applies to air performance ratings and water penetration ratings

Ratings do not include the effect of a bird screen.


LOU

VE

RS

Product Information


Extruded AluminumZE439

Models Blade Louvers 39° Z-Blade ZE439

Price ZE439 stationary louvers feature alloy 6063-T5 extruded aluminum blades. The louver features a “Z” blade profile in a 4” deep assembly with the blades positioned at a 39° angle. The drainable head and jambs enable the louver to achieve optimum air performance and water penetration ratings. This Z-blade louver is available with visible mullions that are joined with an extruded aluminum “I” connection, or continuous horizontal blades that utilize concealed blade braces and hidden vertical supports in place of jamb frames to present uninterrupted horizontal blade appearance.

Performances of louvers manufactured by Price are based on tests and procedures in accordance with AMCA Publication 511 and comply with the requirements of the AMCA Certified Rating Program.

Features• "Z" Blade Profile.• .081” Extruded Aluminum Blades and














ZE439

Continuous Blade

Visible Mullion




Frame .081” (2 mm)


Blade Angle 39o








®

E.H. Price Limited certifies that the ZE439 shown herein is licensed to bear the AMCA Seal. The ratings shown are based on tests and procedures performed in accor-dance with AMCA Publication 511 and comply with the requirements of the AMCA Certified Ratings Program The AMCA Certified Seal applies to air performance ratings and water penetration ratings



LOU

VE

RS

Product Information


Extruded AluminumZE445

Models Blade Louvers 45° Z-Blade ZE445

Price ZE445 stationary louvers feature alloy 6063-T5 extruded aluminum blades. The louver features a “Z” blade profile in a 4” deep assembly with the blades positioned at a 45° angle. The drainable head and jambs enable the louver to achieve optimum air performance and water penetration ratings. This Z-blade louver is available with visible mullions that are joined with an extruded aluminum “I” connection, or continuous horizontal blades that utilize concealed blade braces and hidden vertical supports in place of jamb frames to present uninterrupted horizontal blade appearance.
















ZE445




Frame .081” (2 mm)


Blade Angle 45o








®



Continuous Blade

Visible Mullion


LOU

VE

RS

Product Information

Extruded AluminumDE439

Models

Blade Louvers 39° Blade DE439

Price DE439 stationary drainable louvers feature alloy 6063-T5 extruded 4” aluminum blades positioned at a 39° angle. The drain-able louvers achieve optimum air perform-ance and water penetration ratings with vertical and horizontal gutter systems that capture droplets before they cascade from blade to blade and are entrained in the air-stream. This louver is available with visible mullions that are joined with an extruded aluminum “I” connection, or continuous horizontal blades that utilize concealed blade braces and hidden vertical supports in place of jamb frames to present uninterrupted horizontal blade appearance.


Features• Drainable Blade.• .081” Extruded Aluminum Blades and

Frames.• Nominal 53.6% free area (based on

48”x 48”).• Integral perimeter caulking stop.• 1/2" x 1/2" (12 x 12) 16 gauge Expanded










Blade Louvers 4" (102 mm) Deep


DE439




Frame .081” (2 mm)


Blade Angle 39o









®

E.H. Price Limited certifies that the DE439 shown herein is licensed to bear the AMCA Seal. The ratings shown are based on tests and procedures performed in accor-dance with AMCA Publication 511 and comply with the requirements of the AMCA Certified Ratings Program The AMCA Certified Seal applies to air performance ratings and water penetration ratings



LOU

VE

RS

Product Information

Extruded AluminumDE635



DE635




Frame .081” (2 mm)


Blade Angle 35o

Performance Rating AMCA Standard Standard 500L




Free Area Velocity at Beginning Point of 1,041 FPM Water Penetration (1) (317 m/min)




Models

Blade Louvers 35° Blade DE635

Price DE635 stationary drainable louvers feature alloy 6063-T5 extruded 6” aluminum blades positioned at a 35° angle. The drain-able louvers achieve optimum air perform-ance and water penetration ratings with vertical and horizontal gutter systems that capture droplets before they cascade from blade to blade and are entrained in the air-stream. This louver is available with visible mullions that are joined with an extruded aluminum “I” connection, or continuous horizontal blades that utilize concealed blade braces and hidden vertical supports in place of jamb frames to present uninterrupted horizontal blade appearance.


Features• Drainable Blade.•WeldedConstruction.•.081” Extruded Aluminum Blades and




Options• Extended Sill (loose) 14 GA. Aluminum.• Continuous Blade Sections (invisible








®




LOU

VE

RS

Product Information

Extruded AluminumNJE2

Models

Blade Louvers 30° J-Blade NJE2

Price NJE2 stationary louvers feature alloy 6063-T5 extruded aluminum blades. The louver features a “J” blade profile in a 2” deep assembly with the blades positioned at a 30° angle. This J-blade louver is available with visible mullions that are joined with an extruded aluminum “I” connection, or continuous horizontal blades that utilize concealed blade braces and hidden vertical supports in place of jamb frames to present uninterrupted horizontal blade appearance.

Features• "J" Blade Profile.• .064” Extruded Aluminum Blades and









Prime Coat, Custom Finishes, Clear Anodized and Colour Anodized.

• Select from PRICE Colour Chart orprovide colour sample to match.


Product Information IndexAccessories ............................................... L10Suggested Specification .......................... L11


(1) Beginning point of water penetration is defined as the free area velocity at which 0.01 ounces of water per square foot of free area is measured to pass through a 4' x 4' louver during a 15 minute test.

NJE2

Louver Type Visible Mullion


Stationary Blade .064” (1.6 mm)

Frame .064” (1.6 mm)


Blade Angle 30o








2" (51)



LOU

VE

RS

Product Information

Extruded AluminumNSE1

Models

Blade Louvers Straight Blade NSE1

Price NSE1 stationary louvers feature alloy 6063-T5 extruded aluminum blades. The louver features a straight blade profile in a 1.5” deep assembly. This straight blade louver is available with visible mullions that are joined with an extruded aluminum “I” connection, or continuous horizontal blades that utilize concealed blade braces and hidden vertical supports in place of jamb frames to present uninterrupted horizontal blade appearance.

Features• .125” Extruded Aluminum Blades.• Nominal 69.3% free area (based on 48”x












Blade Louvers1.5" (38 mm) Deep


NSE1




Frame .064” (1.6 mm)

Louver Depth 1.5” (38 mm)

Blade Angle 29°




Free Area Velocity at Beginning Point of N/A Water Penetration (1)

Air Volume Delivered at Beginning Point of N/A Water Penetration (1)

Pressure Drop at Beginning Point of N/A Water Penetration (1)




LOU

VE

RS

Product Information

FormedAluminumQA645

Models Blade Louvers 45° Blade QA645

Price QA645 stationary louvers feature formed aluminum blades. The louver features an acoustic blade profile in a 6” deep assembly with the blades positioned at a 45° angle. This acoustic blade louver is available with visible mullions that are joined with an extruded aluminum “I” connection, or continuous horizontal blades that utilize concealed blade braces and hidden vertical supports in place of jamb frames to present uninterrupted horizontal blade appearance.

Features• Acoustic Blade.• .081” Formed Aluminum Blades and















QA645




Perforated Liner .032” (8 mm)

Frame .081” (2 mm)


Blade Angle 45o








Free-Field Noise Reduction In Decibels

Selected 1/3 Octave Bands Center Frequency (Hz)

63 125 250 500 1,000 2,000 4,000 8,000 13 8 10 13 21 25 22 23


Acoustic performance ratings are determined with ASTM Designations E90-97 "Recommended Practice for Laboratory Measurement at Airborne Sound Transmission Loss at Building Partitions", and E413 3-87 "Standard Classification for Determination of Sound Transmission Loss Class".


LOU

VE

RS

Product Information

FormedAluminumQA1245

ModelsBlade Louvers 45° Blade QA1245

Price QA1245 stationary louvers feature formed aluminum blades. The louver features an acoustic blade profile in a 12” deep assembly with the blades positioned at a 45° angle. This acoustic blade louver is available with visible mullions that are joined with an extruded aluminum “I” connection, or continuous horizontal blades that utilize concealed blade braces and hidden vertical supports in place of jamb frames to present uninterrupted horizontal blade appearance.

Features• Acoustic Blade.•.081” Extruded Aluminum Blades and














QA1245





Frame .081” (2 mm)


Blade Angle 45o










63 125 250 500 1,000 2,000 4,000 8,000 16 13 15 18 16 18 18 21




LOU

VE

RS

Product Information

Extruded AluminumRSE5

Models Blade Louvers 39° Blade RSE5

Price RSE5 stationary drainable louvers feature alloy 6063-T5 extruded aluminum. The drainable louvers achieve optimum air performance and water penetration ratings with vertical and horizontal gutter systems that capture droplets before they cascade from blade to blade and are entrained in the airstream. This louver is available with vis-ible mullions that are joined with an extruded aluminum “I” connection, or continuous horizontal blades that utilize concealed blade braces and hidden vertical supports in place of jamb frames to present uninterrupted horizontal blade appearance.


Frames.• Nominal 57% free area (based on 48”x












RSE5

Product Information IndexAccessories .............................................L23Suggested Specification ........................ L27

Louver Type: Storm Class

Material: Extruded Aluminum (Alloy 6063-T5)

Front Blade: 0.081" (2.06mm)

Back Blade: N/A

Frame: 0.081" (2.06mm)

Louver Depth: 5" (127.0mm)

Water Penetration Test: Simulated Rain

% Free Area: 38.5%

Free Area – 6.16 sq. ft. 4' x 4' Unit: (0.572 sq m)

Ext Wind Velocity: 29.1 mph (13 m/s)

Rainfall Rate: 2.95"/H (75 ml/H)

Effectiveness Ratio: 99.73%



LOU

VE

RS

Product Information

Extruded AluminumMCJE443

Models

Blade Louvers 43° J-Blade MCJE443

Price MCJE443 stationary louvers feature alloy 6063-T5 extruded aluminum blades. The louver features a “J” blade profile in a 4” deep assembly with the blades positioned at a 43° angle. This J-blade louver is available with visible mullions that are joined with an extruded aluminum “I” connection, or continuous horizontal blades that utilize concealed blade braces and hidden vertical supports in place of jamb frames to present uninterrupted horizontal blade appearance.




Aluminum Bird Screen without frame.• Mill finish.• Continuous Blade Sections (invisible

mullions).

Options• WeldedConstruction.• Extended Sill (loose) 14 GA. Aluminum.• Blank-offs are available in Aluminum





• Select from PRICE Colour Chart orprovide colour sample to match.




MCJE443

Louver Type Continuous Blade



Frame .081” (2 mm)


Blade Angle 43o


Free Area – 28.00 sq.ft. 4’ x 4’ x 50.625" Unit (2.601 sq.m.)



Sectionned Roofwith StandingSeams on SizesGreater than45" x 93" (1143 x 2362)

4"(102)

Outside PenthouseDimension (Inside

Penthouse Dimension+ 12" (305))

CurbInside Curb Dimension

Flashing & CurbBy Others

PenthouseHeight

For performance information, please refer to page 3.


LOU

VE

RS

Product Information

Extruded AluminumMCZE439

Models Blade Louvers 39° Z-Blade MCZE439

Price MCZE439 stationary louvers feature alloy 6063-T5 extruded aluminum blades. The louver features a “Z” blade profile in a 4” deep assembly with the blades positioned at a 39° angle. The drainable head and jambs enable the louver to achieve optimum air performance and water penetration ratings. This Z-blade louver is available with visible mullions that are joined with an extruded aluminum “I” connection, or continuous horizontal blades that utilize concealed blade braces and hidden vertical supports in place of jamb frames to present uninterrupted horizontal blade appearance.




Aluminum Bird Screen without frame.• Mill finish.• Continuous Blade Sections (invisible

mullions).









MCZE439

Sectionned Roofwith StandingSeams on SizesGreater than45" x 93" (1143 x 2362)Penthouse

Height




Inside Curb DimensionCurb

4"(102)




Frame .081” (2 mm)


Blade Angle 39o


Free Area – 32.35 sq.ft. 48’ x 48’ x 49.438 Unit (3.005 sq.m.)




For performance information, please refer to page 4


LOU

VE

RS

Product Information


Extruded AluminumMCZE445

Models Blade Louvers 39° Z-Blade MCZE445

Price MCZE445 stationary louvers feature alloy 6063-T5 extruded aluminum blades. The louver features a “Z” blade profile in a 4” deep assembly with the blades positioned at a 45° angle. The drainable head and jambs enable the louver to achieve optimum air performance and water penetration ratings. This Z-blade louver is available with visible mullions that are joined with an extruded aluminum “I” connection, or continuous horizontal blades that utilize concealed blade braces and hidden vertical supports in place of jamb frames to present uninterrupted horizontal blade appearance.




Aluminum Bird Screen without frame.• Continuous Blade Sections (invisible

mullions).• Mill finish.









MCZE445




Frame .081” (2 mm)


Blade Angle 45o


Free Area – 27.51 sq.ft. 48" x 48" x 50.625" Unit (2.556 sq.m.)


PenthouseHeight




Inside Curb Dimension


Curb

4"(102)

For performance information, please refer to page 5


LOU

VE

RS

Product Information

Extruded AluminumMCDE439

Models

Blade Louvers 39° Blade MCDE439

Price MCDE439 stationary drainable louvers feature alloy 6063-T5 extruded 4” aluminum blades positioned at a 39° angle. The drainable louvers achieve optimum air performance and water penetration ratings with vertical and horizontal gutter systems that capture droplets before they cascade from blade to blade and are entrained in the airstream. This louver is available with visible mullions that are joined with an extruded aluminum “I” connection, or continuous horizontal blades that utilize concealed blade braces and hidden vertical supports in place of jamb frames to present uninterrupted horizontal blade appearance.














MCDE439





Frame .081” (2 mm)


Blade Angle 39o




PenthouseHeight






Curb

6"(152)



LOU

VE

RS

Product Information

Extruded AluminumMCDE635


MCDE635


Models

Blade Louvers 35° Blade MCDE635

Price MCDE635 stationary drainable louvers feature alloy 6063-T5 extruded 6” aluminum blades positioned at a 35° angle. The drainable louvers achieve optimum air performance and water penetration ratings with vertical and horizontal gutter systems that capture droplets before they cascade from blade to blade and are entrained in the airstream. This louver is available with visible mullions that are joined with an extruded aluminum “I” connection, or continuous horizontal blades that utilize concealed blade braces and hidden vertical supports in place of jamb frames to present uninterrupted horizontal blade appearance.
















Frame .081” (2 mm)


Blade Angle 35o




PenthouseHeight






Curb

4"(102)



LOU

VE

RS

Product Information

Extruded AluminumBCJE443

Models

Blade Louvers 43° J-Blade BCJE443

Price BCJE443 stationary louvers feature alloy 6063-T5 extruded aluminum blades. The louver features a “J” blade profile in a 4” deep assembly with the blades positioned at a 43° angle. This J-blade louver is available with visible mullions that are joined with an extruded aluminum “I” connection, or continuous horizontal blades that utilize concealed blade braces and hidden vertical supports in place of jamb frames to present uninterrupted horizontal blade appearance.














BCJE443





Frame .081” (2 mm)


Blade Angle 43o


Free Area – 31.59 sq.ft. 4" x 4" x 4" Unit (2.935 sq.m.)


PenthouseHeight


Curb Mounting Straps

OutsidePenthouseDimension

(Inside Curb Dim.+ 8" (203))



4"(102)



LOU

VE

RS

Product Information


Extruded AluminumBCZE439

Models Blade Louvers 39° Z-Blade BCZE439

Price BCZE439 stationary louvers feature alloy 6063-T5 extruded aluminum blades. The louver features a “Z” blade profile in a 4” deep assembly with the blades positioned at a 39° angle. The drainable head and jambs enable the louver to achieve optimum air performance and water penetration ratings. This Z-blade louver is available with visible mullions that are joined with an extruded aluminum “I” connection, or continuous horizontal blades that utilize concealed blade braces and hidden vertical supports in place of jamb frames to present uninterrupted horizontal blade appearance.













BCZE439




Frame .081” (2 mm)


Blade Angle 39o






LOU

VE

RS

Product Information


Extruded AluminumBCZE445

Models Blade Louvers 39° Z-Blade BCZE445

Price BCZE445 stationary louvers feature alloy 6063-T5 extruded aluminum blades. The louver features a “Z” blade profile in a 4” deep assembly with the blades positioned at a 45° angle. The drainable head and jambs enable the louver to achieve optimum air performance and water penetration ratings. This Z-blade louver is available with visible mullions that are joined with an extruded aluminum “I” connection, or continuous horizontal blades that utilize concealed blade braces and hidden vertical supports in place of jamb frames to present uninterrupted horizontal blade appearance.













BCZE445




Frame .081” (2 mm)


Blade Angle 45o




PenthouseHeight

Flashing & CurbBy Others Curb Mounting Straps

Outside PenthouseDimension




4"(102)



LOU

VE

RS

Product Information

Extruded AluminumBCDE439

Models

Blade Louvers 39° Blade BCDE439

Price BCDE439 stationary drainable louvers feature alloy 6063-T5 extruded 4” aluminum blades positioned at a 39° angle. The drainable louvers achieve optimum air performance and water penetration ratings with vertical and horizontal gutter systems that capture droplets before they cascade from blade to blade and are entrained in the airstream. This louver is available with visible mullions that are joined with an extruded aluminum “I” connection, or continuous horizontal blades that utilize concealed blade braces and hidden vertical supports in place of jamb frames to present uninterrupted horizontal blade appearance.


Frames.• Nominal 55.3% free area (based on 48”

x 48”).• Integral perimeter caulking stop.• 1/2" x 1/2" (12 x 12) 16 gauge Expanded










BCDE439





Frame .081” (2 mm)


Blade Angle 39o



Percent Free Area 55.3% For performance information, please refer to page 6.


LOU

VE

RS

Product Information

Extruded AluminumBCDE635


BCDE635


Models

Blade Louvers 35° Blade BCDE635

Price BCDE635 stationary drainable louvers feature alloy 6063-T5 extruded 6” aluminum blades positioned at a 35° angle. The drainable louvers achieve optimum air performance and water penetration ratings with vertical and horizontal gutter systems that capture droplets before they cascade from blade to blade and are entrained in the airstream. This louver is available with visible mullions that are joined with an extruded aluminum “I” connection, or continuous horizontal blades that utilize concealed blade braces and hidden vertical supports in place of jamb frames to present uninterrupted horizontal blade appearance.

Features• Drainable Blade.•.081” Extruded Aluminum Blades and














Frame .081” (2 mm)


Blade Angle 35o




PenthouseHeight







6"(152)

Curb



LOU

VE

RS

Louver Accessories

Accessories

The extruded polystyrene insulation is factory mounted with panel screws.• Aluminum blank-off panels – available with or without insulation Insulated blank-off panels available in 1”, 1-½”, 2” and 3” insulation thickness.

• Gauges available 14 and 18 ga. (Aluminum construction only)

Loose sill is available in 4” to 10” widths in 14-gauge aluminum construction. For single sections, the length of the sill must be equal to the opening width, with a maximum section length of 120” (3048mm). For multiple sections, the minimum recommended overlap is 6” (152mm) with a sealant in between (minimum ¼” bead).

Formed Metal SillBlank-offs

Bird screens are ½” (12.7mm), ¾” (19.1mm) or 1: (25.4mm) mesh, 0.063” (1.60mm) diameter screen in non-rewirable U-shaped frames for permanently securing screen mesh. Bird screens are available in expanded aluminum and expanded aluminum with frame construction. Gauges available – 051, 16 and 19 ga. Available for interior or exterior mounting.

Bird Screen Insect Screen

Insect screens are 18 x 16 (1.4 x 1.6 mm) mesh, 0.012" (0.30mm) diameter screen in non-rewirable U-shaped frames for permanently securing screen mesh. Insect screens are available in aluminum or bronze construction. Gauges available - 051, 16 and 19 ga. Available for interior or exterior mounting.


LOU

VE

RS

Louvers

Suggested Specification

JE443J-Blade Stationary Louver FurnishandinstallPRICEModelJE443Ar-chitectural Blade Louver of size and shape indicated on the plans and/or as described in schedules. Louvers shall be constructed en-tirely of extruded aluminum, alloy 6063-T5. Blades and frames shall be minimum 0.081” (2.06mm) wall thickness. Louver assemblies shall be 4” (101.6mm) deep with 43-degree stationary “J” profile blades.

Louver performance shall be based on tests and procedures in accordance with AMCA publication 511 and comply with the requirements of the AMCA Certified Rating Program.

Louvers shall be designed to withstand a 25 psf (100 mph wind equivalent) wind load.

Each louver shall be fitted with 1/2" (12.7mm) mesh x 0.063" (1.60mm) diameter aluminum bird screen. Bird screen shall be expanded aluminum construction and suitable for {specify:interiororexterior}mounting.

Louvers shall be supplied with a standard mill finish.

If an optional finish is required, please select oneofthefollowing:

• Louvers shall be factory primed and fin-ished-after-assembly with a baked enamel resin coating in a colour selected from the colour chart. Primer and resin coating shall beovenbakedat450°Finaccordancewiththe coating manufacturers instructions.

• Louvers shall receive a Class 2 (clear) anodize finish complying with AAMA 611-98.Finishisappliedtochemicallyetchedand pretreated aluminum to a minimum thickness of 0.4 - 0.7 mil.

• Louvers shall receive a Class 1 (colour) anodize finish complying with AAMA 611-98.Finishisappliedtochemicallyetchedand pretreated aluminum to a minimum thickness of 0.7 - 1.0 mil.Colour shall be Price (specify colour name).

OptionsEach louver shall be fitted with {select required mesh size: 1/2” (12.7mm), 3/4” (19.1mm)or1” (25.4mm)}meshx0.063”(1.60mm) diameter aluminum bird screen in non-rewirable U-shaped frames for per-manently securing screen mesh. Bird screen shall be expanded aluminum construction andsuitablefor{specify:interiororexterior}mounting.

Each louver shall be fitted with 18 x 16 (1.4 x 1.6mm) mesh, 0.012” (0.03mm) diameter aluminum insect screen in non-rewirable U-shaped frames for permanently securing screen mesh. Insect screen shall be suitable

ZE439Z-Blade Stationary Louver FurnishandinstallPRICEModelZE439Ar-chitectural Blade Louver of size and shape indicated on the plans and/or as described in schedules. Louvers shall be constructed en-tirely of extruded aluminum, alloy 6063-T5. Blades and frames shall be minimum 0.081” (2.06mm) wall thickness. Louver assemblies shall be 4” (101.6mm) deep with 39-degree stationary “Z” profile blades.









OptionsEach louver shall be fitted with {select required mesh size: 1/2” (12.7mm), 3/4”

ZE445Z-Blade Stationary Louver FurnishandinstallPRICEModelJE445Ar-chitectural Blade Louver of size and shape indicated on the plans and/or as described in schedules. Louvers shall be constructed en-tirely of extruded aluminum, alloy 6063-T5. Blades and frames shall be minimum 0.081” (2.06mm) wall thickness. Louver assemblies shall be 4” (101.6mm) deep with 45-degree stationary “Z” profile blades.







for{specify:interiororexterior}mounting.

Louvers shall be welded construction.

Louvers shall be supplied with a flanged frame.

Louvers shall be supplied with continuous blade section to give the appearance of invisible mullions.

Each louver shall be fitted with an (insu-lated or non-insulated) aluminum blank-off panel.

(19.1mm)or1”(25.4mm)}meshx0.063”(1.60mm) diameter aluminum bird screen in non-rewirable U-shaped frames for per-manently securing screen mesh. Bird screen shall be expanded aluminum construction andsuitablefor{specify:interiororexterior}mounting.

Each louver shall be fitted with 18 x 16 (1.4 x 1.6mm) mesh, 0.012” (0.03mm) diameter aluminum insect screen in non-rewirable U-shaped frames for permanently secur-ing screen mesh. Insect screen shall be suitable for {specify: interior or exterior}mounting.






LOU

VE

RS

Louvers





•Louvers shall be factory primed and fin-ished-after-assembly with a baked enamel resin coating in a colour selected from the colour chart. Primer and resin coating shall beovenbakedat450°Finaccordancewiththe coating manufacturers instructions.




Each louver shall be fitted with 18 x 16 (1.4 x 1.6mm) mesh, 0.012” (0.03mm) diameter aluminum insect screen in non-rewirable U-shaped frames for permanently securing screen mesh. Insect screen shall be suitable for{specify:interiororexterior}mounting.





{specify:interiororexterior}mounting.




•Louvers shall receive a Class 2 (clear) anodize finish complying with AAMA 611-98.Finishisappliedtochemicallyetchedand pretreated aluminum to a minimum thickness of 0.4 - 0.7 mil.

• Louvers shall receive a Class 1 (colour) anodize finish complying with AAMA 611-98.Finishisappliedtochemicallyetchedand pretreated aluminum to a minimum thickness of 0.7 - 1.0 mil. Colour shall be Price (specify colour name).

OptionsEach louver shall be fitted with 18 x 16 (1.4 x 1.6mm) mesh, 0.012” (0.03mm) diameter aluminum insect screen in non-rewirable U-shaped frames for permanently securing screen mesh. Insect screen shall be suitable for{specify:interiororexterior}mounting.













DE439Drainable LouverFurnish and install PRICE Model DE439Drainable Louver of size and shape indi-cated on the plans and/or as described in schedules. Louvers shall be constructed en-tirely of extruded aluminum, alloy 6063-T5. Blades and frames shall be minimum 0.081” (2.06mm) wall thickness. Louver assemblies shall be 4” (101.6mm) deep with 39-degree stationary drainable blades.



Each louver shall be fitted with 1/2" (12.7mm) mesh x 0.063" (1.60mm) diameter aluminum bird screen. Bird screen shall be expanded aluminum construction and suitable for

DE635Drainable Louver Furnish and install PRICE Model DE635Drainable Louver of size and shape indi-cated on the plans and/or as described in schedules. Louvers shall be constructed en-tirely of extruded aluminum, alloy 6063-T5. Blades and frames shall be minimum 0.081” (2.06mm) wall thickness. Louver assemblies shall be 6” (152.4mm) deep with 35-degree stationary drainable blades.




LOU

VE

RS

QA645Acoustic Blade Stationary Louver Furnish and install PRICE Model QA645Architectural Blade Louver of size and shape indicated on the plans and/or as described in schedules. Louvers shall be constructed entirely of formed aluminum, alloy 6063-T5. Blades and frames shall be minimum 0.081” (2.06mm) wall thickness. Louver assemblies shall be 6” (152mm) deep with 45-degree stationary acoustic profile blades.





• Louvers shall be factory primed and finished-after-assembly with a baked enamel resin coating in a colour se-lected from the colour chart. Primer and resin coating shall be oven baked at450°F inaccordancewith thecoating manufacturers instructions.



OptionsEach louver shall be fitted with {select required mesh size: 1/2” (12.7mm), 3/4”(19.1mm)or1” (25.4mm)}meshx0.063”(1.60mm) diameter aluminum bird screen

Louvers


NJE2J-Blade Stationary Louver FurnishandinstallPRICEModelNSE2Ar-chitectural Blade Louver of size and shape indicated on the plans and/or as described in schedules. Louvers shall be constructed en-tirely of extruded aluminum, alloy 6063-T5. Blades and frames shall be minimum 0.081” (2.06mm) wall thickness. Louver assemblies shall be 2” (51.6mm) deep with 30-degree stationary “J” profile blades.












NCE1Straight Blade Stationary Louver FurnishandinstallPRICEModelNCE1Ar-chitectural Blade Louver of size and shape indicated on the plans and/or as described in schedules. Louvers shall be constructed entirely of extruded aluminum, alloy 6063-T5. Blades and frames shall be minimum 0.081” (2.06mm) wall thickness. Louver as-semblies shall be 1.5” (38.1mm) deep with stationary straight profile blades.









Each louver shall be fitted with 18 x 16 (1.4 x 1.6mm) mesh, 0.012” (0.03mm) diameter aluminum insect screen in non-rewirable



U-shaped frames for permanently securing screen mesh. Insect screen shall be suitable for{specify:interiororexterior}mounting.






LOU

VE

RS

Louvers


in non-rewirable U-shaped frames for per-manently securing screen mesh. Bird screen shall be expanded aluminum construction andsuitablefor{specify:interiororexterior}mounting.






QA1245Acoustic Blade Stationary Louver Furnish and install PRICE Model QA1245Architectural Blade Louver of size and shape indicated on the plans and/or as described in schedules. Louvers shall be constructed entirely of formed aluminum, alloy 6063-T5. Blades and frames shall be minimum 0.081” (2.06mm) wall thickness. Louver assemblies shall be 12” (305mm) deep with 45-degree stationary acoustic profile blades.







• Louvers shall receive a Class 1 (colour) anodize finish complying with AAMA 611-98.Finishisappliedtochemicallyetchedand pretreated aluminum to a minimum

thickness of 0.7 - 1.0 mil.Colour shall be Price (specify colour name).







RSE5Drainable LouverFurnishandinstallPRICEModelRSE5Drain-able Louver of size and shape indicated on the plans and/or as described in schedules. Louvers shall be constructed entirely of ex-truded aluminum, alloy 6063-T5. Blades and frames shall be minimum 0.081” (2.06mm) wall thickness. Louver assemblies shall be 5” (127mm) deep with stationary drainable blades.






•Louvers shall receive a Class 2 (clear) anodize finish complying with AAMA 611-

98.Finishisappliedtochemicallyetchedand pretreated aluminum to a minimum thickness of 0.4 - 0.7 mil.


OptionsEach louver shall be fitted with {select required mesh size: 1/2” (12.7mm), 3/4” (19.1mm)or1”(25.4mm)}meshx0.063”(1.60mm) diameter aluminum bird screen in non-rewirable U-shaped frames for per-manently securing screen mesh. Bird screen shall be expanded aluminum construction andsuitablefor{specify:interiororexterior}mounting.







LOU

VE

RS

Louvers


MCJE443J-Blade Miter Corner Penthouse Louver FurnishandinstallPRICEModelMCJE443Architectural Blade Louver of size and shape indicated on the plans and/or as described in schedules. Louvers shall be constructed en-tirely of extruded aluminum, alloy 6063-T5. Blades and frames shall be minimum 0.081” (2.06mm) wall thickness. Louver assemblies shall be 4” (101.6mm) deep with 43-degree stationary “J” profile blades.








Options

Each louver shall be fitted with {select required mesh size: 1/2” (12.7mm), 3/4” (19.1mm)or1” (25.4mm)}meshx0.063”(1.60mm) diameter aluminum bird screen in non-rewirable U-shaped frames for per-manently securing screen mesh. Bird screen shall be expanded aluminum construction andsuitablefor{specify:interiororexterior}mounting.




MCZE439Z-Blade Miter Corner Penthouse Louver FurnishandinstallPRICEModelMCZE439Architectural Blade Louver of size and shape indicated on the plans and/or as described in schedules. Louvers shall be constructed en-tirely of extruded aluminum, alloy 6063-T5. Blades and frames shall be minimum 0.081” (2.06mm) wall thickness. Louver assemblies shall be 4” (101.6mm) deep with 39-degree stationary “Z” profile blades.









Each louver shall be fitted with 18 x 16 (1.4 x 1.6mm) mesh, 0.012” (0.03mm) diameter aluminum insect screen in non-rewirable

MCZE445Z-Blade Miter Corner Penthouse Louver FurnishandinstallPRICEModelMCZE445Architectural Blade Louver of size and shape indicated on the plans and/or as described in schedules. Louvers shall be constructed en-tirely of extruded aluminum, alloy 6063-T5. Blades and frames shall be minimum 0.081” (2.06mm) wall thickness. Louver assemblies shall be 4” (101.6mm) deep with 45-degree stationary “Z” profile blades.








OptionsEach louver shall be fitted with {select required mesh size: 1/2” (12.7mm), 3/4” (19.1mm)or1” (25.4mm)}meshx0.063”(1.60mm) diameter aluminum bird screen



U-shaped frames for permanently securing screen mesh. Insect screen shall be suitable for{specify:interiororexterior}mounting.






LOU

VE

RS

Louvers








98.Finishisappliedtochemicallyetchedand pretreated aluminum to a minimum thickness of 0.7 - 1.0 mil. Colour shall be Price (specify colour name).







MCDE439Drainable Blade Miter Corner Penthouse LouverFurnishandinstallPRICEModelMCDE439Drainable Louver of size and shape indi-cated on the plans and/or as described in schedules. Louvers shall be constructed en-tirely of extruded aluminum, alloy 6063-T5. Blades and frames shall be minimum 0.081” (2.06mm) wall thickness. Louver assemblies shall be 4” (101.6mm) deep with 39-degree stationary drainable blades.







• Louvers shall receive a Class 1 (colour) anodize finish complying with AAMA 611-

MCDE635Drainable Blade Miter Corner Penthouse Louver FurnishandinstallPRICEModelMCDE635Drainable Louver of size and shape indi-cated on the plans and/or as described in schedules. Louvers shall be constructed en-tirely of extruded aluminum, alloy 6063-T5. Blades and frames shall be minimum 0.081” (2.06mm) wall thickness. Louver assemblies shall be 6” (152.4mm) deep with 35-degree stationary drainable blades.








OptionsEach louver shall be fitted with {select required mesh size: 1/2” (12.7mm), 3/4” (19.1mm)or1”(25.4mm)}meshx0.063”(1.60mm) diameter aluminum bird screen in non-rewirable U-shaped frames for permanently securing screen mesh. Bird screen shall be expanded aluminum con-structionandsuitablefor{specify:interiororexterior}mounting.







LOU

VE

RS

BCJE443J-Blade Box Corner Penthouse Louver FurnishandinstallPRICEModelBCJE443Architectural Blade Louver of size and shape indicated on the plans and/or as described in schedules. Louvers shall be constructed en-tirely of extruded aluminum, alloy 6063-T5. Blades and frames shall be minimum 0.081” (2.06mm) wall thickness. Louver assemblies shall be 4” (101.6mm) deep with 43-degree stationary “J” profile blades.








Options

Each louver shall be fitted with {select required mesh size: 1/2” (12.7mm), 3/4” (19.1mm)or1” (25.4mm)}meshx0.063”(1.60mm) diameter aluminum bird screen in non-rewirable U-shaped frames for per-manently securing screen mesh. Bird screen shall be expanded aluminum construction andsuitablefor{specify:interiororexterior}mounting.




BCZE439Z-Blade Box Corner Penthouse Louver FurnishandinstallPRICEModelBCZE439Architectural Blade Louver of size and shape indicated on the plans and/or as described in schedules. Louvers shall be constructed en-tirely of extruded aluminum, alloy 6063-T5. Blades and frames shall be minimum 0.081” (2.06mm) wall thickness. Louver assemblies shall be 4” (101.6mm) deep with 39-degree stationary “Z” profile blades.









Each louver shall be fitted with 18 x 16 (1.4 x 1.6mm) mesh, 0.012” (0.03mm) diameter

BCZE445Z-Blade Box Corner Penthouse Louver FurnishandinstallPRICEModelBCZE445Architectural Blade Louver of size and shape indicated on the plans and/or as described in schedules. Louvers shall be constructed en-tirely of extruded aluminum, alloy 6063-T5. Blades and frames shall be minimum 0.081” (2.06mm) wall thickness. Louver assemblies shall be 4” (101.6mm) deep with 45-degree stationary “Z” profile blades.








OptionsEach louver shall be fitted with {select required mesh size: 1/2” (12.7mm), 3/4” (19.1mm)or1” (25.4mm)}meshx0.063”(1.60mm) diameter aluminum bird screen

Louvers




aluminum insect screen in non-rewirable U-shaped frames for permanently securing screen mesh. Insect screen shall be suitable for{specify:interiororexterior}mounting.






LOU

VE

RS

Louvers








BCDE439Drainable Blade Box Corner Penthouse LouverFurnish and install PRICE Model DE439Drainable Louver of size and shape indi-cated on the plans and/or as described in schedules. Louvers shall be constructed en-tirely of extruded aluminum, alloy 6063-T5. Blades and frames shall be minimum 0.081” (2.06mm) wall thickness. Louver assemblies shall be 4” (101.6mm) deep with 39-degree stationary drainable blades.







• Louvers shall receive a Class 1 (colour) anodize finish complying with AAMA 611-

98.Finishisappliedtochemicallyetchedand pretreated aluminum to a minimum thickness of 0.7 - 1.0 mil. Colour shall be Price (specify colour name).







BCDE635Drainable Blade Box Corner Penthouse Louver Furnish and install PRICE Model DE635Drainable Louver of size and shape indi-cated on the plans and/or as described in schedules. Louvers shall be constructed en-tirely of extruded aluminum, alloy 6063-T5. Blades and frames shall be minimum 0.081” (2.06mm) wall thickness. Louver assemblies shall be 6” (152.4mm) deep with 35-degree stationary drainable blades.















LOU

VE

RS

Louvers

Price / Airolite Cross Reference

Price Airolite

JE443 K638X

ZE439 K609HP

ZE445 K609X

DE439 K6774X

DE635 K6776X

NJE2 T6382X

NSE1 AC5O5X

QA645 T9106X

QA1245 T9112X

RSE5 SCH5X

MCJE443 MC909-638X

MCZE439 MC909-609HP

MCZE445 M6909-609X

MCDE439 MC909-6774X

MCDE635 MC909-6776X

BCJE443 K909-638X

BCZE439 K909-609HP

BCZE445 K909-609X

BCDE439 K909-6774X

BCDE635 K909-6776X

© Copyright E.H. Price Limited 2006. All Metric dimensions ( ) are soft conversion. Imperial dimensions are converted to metric and rounded to the nearest millimetre. LP-�

LOU

VE

RS

Louvers Performance DataIndex

How to use the Price Nomographs ...................................................................................................... LP2 - LP3JE443 Stationary Louvers .................................................................................................................. LP4ZE439 Stationary Louvers .................................................................................................................. LP6ZE445 Stationary Louvers .................................................................................................................. LP8DE439 Stationary Drainable Louvers .............................................................................................. LP�0DE635 Stationary Drainable Louvers .............................................................................................. LP�2NJE2 Stationary Louvers ............................................................................................................... LP�4NSE� Stationary Louvers ............................................................................................................... LP�6QA645 Stationary Acoustic Louvers ................................................................................................ LP�8QA�245 Stationary Acoustic Louvers ................................................................................................ LP20RSE5 Rain Storm Louvers.............................................................................................................. LP22MCJE443 Miter Corner Penthouse Stationary Louvers ...................................................................... LP24MCZE439 Miter Corner Penthouse Stationary Louvers ...................................................................... LP26MCZE445 Miter Corner Penthouse Stationary Louvers ...................................................................... LP28MCDE439 Miter Corner Penthouse Drainable Louvers ....................................................................... LP30MCDE635 Miter Corner Penthouse Drainable Louvers ....................................................................... LP32BCJE443 Box Corner Penthouse Stationary Louvers ........................................................................ LP34BCZE439 Box Corner Penthouse Stationary Louvers ........................................................................ LP36BCZE445 Box Corner Penthouse Stationary Louvers ........................................................................ LP48BCDE439 Box Corner Penthouse Drainable Louvers ......................................................................... LP40BCDE635 Box Corner Penthouse Drainable Louvers ......................................................................... LP42

Extruded Aluminum

© Copyright E.H. Price Limited 2006. All Metric dimensions ( ) are soft conversion. Imperial dimensions are converted to metric and rounded to the nearest millimetre. LP-2

LOU

VE

RS

How to use the Price Nomographs

Extruded AluminumLouvers Performance Data

PRICE has developed this unique graphi-cal tool to help you select PRICE louvers without the use of a calculator.

All you need is a ruler and a pencil. A multitude of “what if” conditions can be quickly evaluated and the working copy of the nomograph can be retained for future reference.

Step �.To use the PRICE Nomographs, you need to know at least 3 of the following 6 variables: the louver width and height, the louver free area, the air volume, free area air velocity or static pressure loss. The possible starting point combinations are as follows:One louver dimension – flow rate – free area velocityOne louver dimension – flow rate - pressure dropOne louver dimension – flow rate – free areaTwo louver dimensions – flow rateTwo louver dimensions – pressure drop

Two louver dimensions – free area velocity

Step 2. The PRICE Nomograph is com-prised of 2 interrelated areas. The dimen-sional characteristics are on the left side of the sheet and the air flow characteris-tics are on the right. Drawing a line joining the “Louver Width” (W scale) to the “Lou-ver Height” (H scale), you obtain the free area as the line crosses the “Louver Free Area” (A scale). You can also start with the free area and one dimension to obtain the 2nd dimension.

Step 3. Drawing a second line joining the “Louver Free Area” (A scale) (ob-tained in step 2) to the “Louver Air Flow” (F scale), you obtain the free area veloc-ity and pressure drop as the line crosses the “Pressure drop / Free area velocity” (P-V scale). The line can also be drawn with any combination of 2 starting points: [free area & pressure drop] or [flow rate & pressure drop] or [flow rate & free area velocity].

The PRICE Nomographs give you maxi-mum flexibility in the selection of your PRICE louvers.

See the examples on the following page for more details.


LOU

VE

RS

How to use the Price Nomographs (cont'd)

Extruded AluminumLouvers Performance Data

EXAMPLES:1. The louver size is 36” wide by 72” high

and the required intake air volume is 6,000 CFM. What is the free area, the pressure drop and the free area velocity?

a). Draw a line joining 36” wide on the “Louver Width” (W scale) to 72” high on the “Louver Height” (H scale).

b). Read the free area at the point where the line meets the “Louver Free Area” (A scale).

ANSWER The louver free area is �0.02 square feet.

c). Draw a line joining 6,000 CFM on the “Air Flow” (F scale) to the free area you just found.

d). Read the free area velocity and static pressure loss at the point where this second line meets the “Pressure Drop/Free Area Veloc-ity” (P-V scale).

ANSWER The free area air velocity is 600 FPM and louver static pressure loss is 0.06”.

2. The louver exhaust air volume is 6,000 CFM and expected static pressure loss is 0.06”. Louver height must be small-er or equal to 72”.What is the required free area and minimum louver width?

a). Apply pressure drop correction factor for exhaust condition 0.06" ÷ 0.825 = 0.07" WG

b). Draw a line joining 6,000 CFM on the “Air Flow” (F scale) to the cal-culated static pressure loss on the “Pressure Drop/Free Air Velocity” (P-V scale) and continuing to the “Louver Free Area” (A scale).

c). Read the free area at the point where the line meets the “Louver Free Area” (A scale).

ANSWER The louver free area is �0.02 square feet.

d). Draw a line joining the 72” high on the “Louver Height” (H scale) to the free area and continuing to the “Louver Width” (W scale).

e). Read the required louver width. ANSWER The minimum louver width

is 36”.

For example purposes only.


LOU

VE

RS

Extruded Aluminum - Fixed BladesJE44343 Degree J-Blades

Performance Data ®

Ratings do not include theeffect of a bird screen.

ZE443-060101-0

E.H. Price Limited certifies that the JE443 shown herein is licensed to bear the AMCA Seal. The ratings shown are based on tests and procedures performed in accor-dance with AMCA Publication 511 and comply with the requirements of the AMCA Certified Ratings Program The AMCA Certified Seal applies to air performance ratings and water penetration ratings

All Metric dimensions ( ) are soft conversion. © Copyright E.H. Price Limited 2006. Imperial dimensions are converted to metric and rounded to the nearest millimetre. LP-5

LOU

VE

RS

Extruded Aluminum - Fixed BladesJE44343 Degree J-Blades

Architectural Blade Louvers4" (�02 mm) Deep

Features• Storm proof blade with rain check.• All welded construction: minimum 1” fillet welds.• Available in continuous blade construction (CB models).• Nominal 51% free area (based on 48” x 48”).• Integral perimeter caulking stop.• Optional integral 1.5” flanges. Other sizes available as add-ons.• Optional bird and insect screens available.• Optional Duracron, Duranar and Duranar-XL baked enamel finish as per our standard

color chart or any custom color.


ALL-WELDED CONSTRUCTION

(1) Beginning point of water penetration is defined by AMCA standard 511 as the free area velocity at which 0.01 ounces of water per square foot of free area is measured to pass througha 4' x 4' louver during a 15 minute test.





Frame .081” (2 mm)


Blade Angle 43o







Pressure Drop at Beginning Point of 0.07” H2O Water Penetration (1) (18 Pa)


LOU

VE

RS

Extruded Aluminum - Fixed BladesZE43939 Degree Z-Blades

Performance Data ®


JE439-060101-0



LOU

VE

RS

Continuous Blade

Visible Mullion

Extruded Aluminum - Fixed BladesZE43939 Degree Z-Blades


Features• High performance louver with drainable frame.• All welded construction: minimum 1” fillet welds.• Available in continuous blade construction (CB models).• Nominal 52% free area (based on 48” x 48”).• Integral perimeter caulking stop.• Optional integral 1.5” flanges. Other sizes available as add-ons.• Optional bird and insect screens available.• Optional Duracron, Duranar and Duranar-XL baked enamel finish as per our standard









Frame .081” (2 mm)


Blade Angle 39o









LOU

VE

RS

Extruded Aluminum - Fixed Blades ZE44545 Degrees Z-Blade

Performance Data

®


JE445-060101-0



LOU

VE

RS

Extruded Aluminum - Fixed Blades ZE44545 Degrees Z-Blade


Features• All welded construction: minimum 1” fillet welds.• Available in continuous blade construction (CB models).• Nominal 50% free area (based on 48” x 48”).• Integral perimeter caulking stop.• Optional integral 1.5” flanges. Other sizes available as add-ons.• Optional bird and insect screens available.• Optional Duracron, Duranar and Duranar-XL baked enamel finish as per our standard





ZE445Blade Louvers4" (102 mm) Deep




Frame .081” (2 mm)


Blade Angle 45o








© Copyright E.H. Price Limited 2006. All Metric dimensions ( ) are soft conversion. Imperial dimensions are converted to metric and rounded to the nearest millimetre. LP-�0

LOU

VE

RS

Extruded Aluminum - Fixed Blades DE439Drainable 39 Degree Blades

Performance Data

®


DE439-060101-0


All Metric dimensions ( ) are soft conversion. © Copyright E.H. Price Limited 2006. Imperial dimensions are converted to metric and rounded to the nearest millimetre. LP-��

LOU

VE

RS

Extruded Aluminum - Fixed Blades DE439Drainable 39 Degree Blades


Features• Drainable blade with vertical jamb gutter.• All welded construction: minimum 1” fillet welds.• Available in continuous blade construction (CB models).• Nominal 54% free area (based on 48” x 48”).• Integral perimeter caulking stop.• Optional integral 1.5” flanges. Other sizes available as add-ons.• Optional bird and insect screens available.• Optional Duracron, Duranar and Duranar-XL baked enamel finish as per our standard





DE439Blade Louvers4" (102 mm) Deep




Frame .081” (2 mm)


Blade Angle 39o









LOU

VE

RS

Extruded Aluminum - Fixed BladesDE635Drainable 35 Degree Blades

Performance Data

®


DE635-060101-0

E.H. Price Limited certifies that the DE635 shown herein is licensed to bear the AMCA Seal. The ratings shown are based on tests and procedures performed in accor-dance with AMCA Publication 511 and comply with the requirements of the AMCA Certified Rateings Program The AMCA Certified Seal applies to air performance ratings and water penetration ratings

All Metric dimensions ( ) are soft conversion. © Copyright E.H. Price Limited 2006. Imperial dimensions are converted to metric and rounded to the nearest millimetre. LP-�3

LOU

VE

RS

Extruded Aluminum - Fixed BladesDE635Drainable 35 Degree Blades


Features• Drainable blade with vertical jamb gutter.• All welded construction: minimum 1” fillet welds.• Available in continuous blade construction (CB models).• Nominal 56% free area (based on 48” x 48”).• Integral perimeter caulking stop.• Optional integral 1.5” flanges. Other sizes available as add-ons.• Optional bird and insect screens available.• Optional Duracron, Duranar and Duranar-XL baked enamel finish as per our standard





DE635Blade Louvers 6" (152 mm) Deep




Frame .081” (2 mm)


Blade Angle 35o





Free Area Velocity at Beginning Point of 1,233 FPM Water Penetration (1) (375 m/min)




LOU

VE

RS

Extruded Aluminum - Fixed BladesNJE230 Degree J-Blades

Performance Data


NZE2-060101-0


LOU

VE

RS

2" (51)

Extruded Aluminum - Fixed BladesNJE230 Degree J-Blades


Features• Storm proof blade with rain check.• All welded construction: minimum 1” fillet welds.• Nominal 44% free area (based on 48” x 48”).• Optional flanges up to 4” available.• Optional bird and insect screens available.• Optional Duracron, Duranar and Duranar-XL baked enamel finish as per our standard




(1) Beginning point of water penetration is defined as the free area velocity at which 0.01 ounces of water per square foot of free area is measured to pass througha 4' x 4' louver during a 15 minute test.

NJE2Blade Louvers2" (5 mm) Deep



Stationary Blade .064” (1.6 mm)

Frame .064” (1.6 mm)


Blade Angle 30o








LOU

VE

RS

Extruded Aluminum - Fixed BladesNSE�Straight Blades

Performance Data



LOU

VE

RS

Extruded Aluminum - Fixed BladesNSE�Straight Blades

Narrow Profile Louvers�.5" (38 mm) Deep

Features• Nominal 69% free area (based on 48” x 48”).• Optional flanges up to 4” available.• Optional bird and insect screens available.• Optional Duracron, Duranar and Duranar-XL baked enamel finish as per our standard




NSE�Blade Louvers1.5" (38 mm) Deep




Frame .064” (1.6 mm)

Louver Depth 1.5” (38 mm)

Blade Angle 29°




Free Area Velocity at Beginning Point of N/A Water Penetration (1)

Air Volume Delivered at Beginning Point of N/A Water Penetration (1)

Pressure Drop at Beginning Point of N/A Water Penetration (1)


LOU

VE

RS

Extruded Aluminum - Fixed BladesQA645Acoustic 45 Degree Blades

Performance Data


QA645-060101-0


LOU

VE

RS

Extruded Aluminum - Fixed BladesQA645Acoustic 45 Degree Blades

Acoutiscal Louvers6" (�52 mm) Deep

Features• All welded construction: minimum 1” fillet welds.• Available in continuous blade construction (FCB models).• Nominal 29% free area (based on 48” x 48”).• Optional integral flanges up to 4”.• Optional bird and insect screens available.• Optional Duracron, Duranar and Duranar-XL baked enamel finish as per our standard


Louvers manufactured by E.H. Price are eligible to bear the Air Movement and Control Association (AMCA) certified rating seals for air performance and water penetration of their equivalent Airolite models where applicable.




QA645Blade Louvers6" (152 mm) Deep





Frame .081” (2 mm)


Blade Angle 45o









LOU

VE

RS

Extruded Aluminum - Fixed BladesQA�245Acoustic 45 Degree Blades

Performance Data


QA1245-060101-0

All Metric dimensions ( ) are soft conversion. © Copyright E.H. Price Limited 2006. Imperial dimensions are converted to metric and rounded to the nearest millimetre. LP-2�

LOU

VE

RS



63 125 250 500 1,000 2,000 4,000 8,000 16 13 15 18 16 18 18 21

Extruded Aluminum - Fixed BladesQA�245Acoustic 45 Degree Blades

Acoutiscal Louvers�2" (305 mm) Deep

Features• All welded construction: minimum 1” fillet welds.• Available in continuous blade construction (FCB models).• Nominal 25% free area (based on 48” x 48”).• Optional integral flanges up to 4”.• Optional bird and insect screens available.• Optional Duracron, Duranar and Duranar-XL baked enamel finish as per our standard





QA�245Blade Louvers12" (305 mm) Deep





Frame .081” (2 mm)


Blade Angle 45o









LOU

VE

RS

Extruded Aluminum - Fixed BladesRSE5Drainable Blades

Performance Data


RSE5-060101-0


LOU

VE

RS

Extruded Aluminum - Fixed BladesRSE5Drainable Blades


Features• Drainable Blade.• .081” Extruded Aluminum Blades and Frames.• Nominal 39% free area (based on 48”x 48”).• Integral perimeter caulking stop.• 1/2" x 1/2" (12 x 12) 16 gauge Expanded Aluminum Bird Screen without frame• Mill finish.



RSE5Blade Louvers 5" (127 mm) Deep

Louver Type: Storm Class

Material: Extruded Aluminum (Alloy 6063-T5)

Front Blade: 0.081" (2.06mm)

Back Blade: N/A

Frame: 0.081" (2.06mm)

Louver Depth: 5" (127.0mm)

Water Penetration Test: Simulated Rain

% Free Area: 38.5%

Free Area – 6.16 sq. ft. 4' x 4' Unit: (0.572 sq m)

Ext Wind Velocity: 29.1 mph (13 m/s)

Rainfall Rate: 2.95"/H (75 ml/H)

Effectiveness Ratio: 99.73%


LOU

VE

RS

Extruded Aluminum - Fixed BladesMCJE44343 Degree J-Blades

Performance Data


LOU

VE

RS


4"(102)



CurbInside Curb Dimension


PenthouseHeight

Extruded Aluminum - Fixed BladesMCJE44343 Degree J-Blades


Features• Storm proof blade with rain check.• Unique bolted conrer design affords excellent alignment of adjoining louver• Designed for snow load up to 50 psf (2,394 Pa), consult your local representative for

higher loading.• All welded construction: minimum 1” fillet welds.• Nominal 42% free area (based on 48” x 48” x 50.625").• Optional bird and insect screens available.• Optional insulated roof and roof curbs are available.• Optional Duracron, Duranar and Duranar-XL baked enamel finish as per our standard




MCJE443Blade Louvers4" (102 mm) Deep




Frame .081” (2 mm)


Blade Angle 43o


Free Area – 28.00 sq.ft. 4’ x 4’ x 50.625" Unit (2.601 sq.m.)



LOU

VE

RS

Extruded Aluminum - Fixed BladesMCZE43939 Degree Z-Blades

Performance Data


LOU

VE

RS

Sectionned Roofwith StandingSeams on SizesGreater than45" x 93" (1143 x 2362)Penthouse

Height





4"(102)


Mitered Corners Penthouse4" (�02 mm) Deep

Features• Unique bolted conrer design affords excellent alignment of adjoining louver.• Drain holes at top blade corners.• Designed for snow load up to 50 psf (2,394 Pa), consult your local representative for





MCZE439Blade Louvers4" (102 mm) Deep




Frame .081” (2 mm)


Blade Angle 39o


Free Area – 32.35 sq.ft. 48’ x 48’ x 49.438 Unit (3.005 sq.m.)



LOU

VE

RS


Performance Data


LOU

VE

RS

PenthouseHeight






Curb

4"(102)



Features• Unique bolted conrer design affords excellent alignment of adjoining louver.• Designed for snow load up to 50 psf (2,394 Pa), consult your local representative for





MCZE445Blade Louvers4" (102 mm) Deep




Frame .081” (2 mm)


Blade Angle 45o





LOU

VE

RS

Extruded Aluminum - Fixed Blades MCDE439Drainable 39 Degree Blades

Performance Data


LOU

VE

RS

PenthouseHeight






Curb

6"(152)

Extruded Aluminum - Fixed Blades MCDE439Drainable 39 Degree Blades

Miterred Corners Penthouse4" (�02 mm) Deep

Features• Unique bolted conrer design affords excellent alignment of adjoining louver.• Drainable blades with drain holes at corners.• Designed for snow load up to 50 psf (2,394 Pa), consult your local representative for





MCDE439Blade Louvers4" (102 mm) Deep




Frame .081” (2 mm)


Blade Angle 39o





LOU

VE

RS

Extruded Aluminum - Fixed BladesMCDE635Drainable 35 Degree Blades

Performance Data


LOU

VE

RS

PenthouseHeight






Curb

4"(102)

Extruded Aluminum - Fixed BladesMCDE635Drainable 35 Degree Blades


Features• Unique bolted conrer design affords excellent alignment of adjoining louver.• Drainable blades with drain holes at corners.• Designed for snow load up to 50 psf (2,394 Pa), consult your local representative for





MCDE635Blade Louvers6" (152 mm) Deep




Frame .081” (2 mm)


Blade Angle 35o





LOU

VE

RS

Extruded Aluminum - Fixed BladesBCJE44343 Degree J-Blades

Performance Data


LOU

VE

RS

PenthouseHeight



OutsidePenthouseDimension




4"(102)

Extruded Aluminum - Fixed BladesBCJE44343 Degree J-Blades

Box Corners Penthouse4" (�02 mm) Deep

Features• Storm proof blade with rain check.• Positive locking corner joiner mounts from exterior.• Slip-on corner cover requires no screws.• Designed for snow load up to 50 psf (2,394 Pa), consult your local representative for

higher loading.• All welded construction: minimum 1” fillet welds.• Nominal 49% free area (based on 48” x 48” x 48”).• Optional bird and insect screens available.• Optional insulated roof and roof curbs are available.• Optional Duracron, Duranar and Duranar-XL baked enamel finish as per our standard




BCJE443Blade Louvers4" (102 mm) Deep




Frame .081” (2 mm)


Blade Angle 43o





LOU

VE

RS

Extruded Aluminum - Fixed BladesBCZE43939 Degree Z-Blades

Performance Data


LOU

VE

RS



Features• Storm proof blade with rain check.• Positive locking corner joiner mounts from exterior.• Slip-on corner cover requires no screws.• Designed for snow load up to 50 psf (2,394 Pa), consult your local representative for





BCZE439Blade Louvers4" (102 mm) Deep




Frame .081” (2 mm)


Blade Angle 39o





LOU

VE

RS


Performance Data


LOU

VE

RS



Features• Positive locking corner joiner mounts from exterior.• Slip-on corner cover requires no screws.• Designed for snow load up to 50 psf (2,394 Pa), consult your local representative for





BCZE445Blade Louvers4" (102 mm) Deep




Frame .081” (2 mm)


Blade Angle 45o




PenthouseHeight

Flashing & CurbBy Others Curb Mounting Straps





4"(102)


LOU

VE

RS

Extruded Aluminum - Fixed BladesBCDE439Drainable 39 Degree Blades

Performance Data


LOU

VE

RS



Features• Drainable blade with vertical jamb gutter.• Positive locking corner joiner mounts from exterior.• Slip-on corner cover requires no screws.• Designed for snow load up to 50 psf (2,394 Pa), consult your local representative for





BCDE439Blade Louvers4" (102 mm) Deep




Frame .081” (2 mm)


Blade Angle 39o





LOU

VE

RS


Performance Data


LOU

VE

RS

PenthouseHeight







6"(152)

Curb



Features• Drainable blade with vertical jamb gutter.• Positive locking corner joiner mounts from exterior.• Slip-on corner cover requires no screws.• Designed for snow load up to 50 psf (2,394 Pa), consult your local representative for





BCDE635Blade Louvers6" (152 mm) Deep




Frame .081” (2 mm)


Blade Angle 35o




Description Submittal Number Date

SubmittalsPage Number:

Effective Date:

Supersedes:

Fixed Blade Extruded Aluminum

JE443 237944 January 1 / 06

ZE439 237945 January 1 / 06

ZE445 243555 January 1 / 06

DE439 237946 January 1 / 06

DE635 237947 January 1 / 06

NJE2 221956 January 1 / 06

NSE1 221944 January 1 / 06

QA645 221912 January 1 / 06

QA1245 243484 January 1 / 06

RSE5 236888 January 1 / 06

MCJE443 221994 January 1 / 06

MCZE439 243497 January 1 / 06

MCZE445 243556 January 1 / 06

MCDE439 221910 January 1 / 06

MCDE635 221893 January 1 / 06

BCJE443 243557 January 1 / 06

BCZE439 243558 January 1 / 06

BCZE445 243559 January 1 / 06

BCDE439 243560 January 1 / 06

BCDE635 243561 January 1 / 06

Mounting Method 228900 January 1 / 06

Insulated Blank-Off Panels with Thermal Break 221914 January 1 / 06

Penthouse Curb 204058 January 1 / 06

SUB-1Aug 1 / 06Initial

© Copyright E.H. Price Limited 2010.

JE443 FIXED BLADE LOUVER

Standard ConstructionFrame. 4" x .081"(101 x 2.1) Extruded Aluminum (6063-T5)Blades. J Style Blades, .081"(2.1) Extruded Aluminum (6063-T5) 430 blade angle, 5"(127) blade spacingFinishes. MILLMinimum Section Size. 9" W x 10 1/2" H (229 x 267)Maximum Section Size. One piece construction 72" W x 120" H (1829 x 3048) or 120" W x 72" H (3048 x 1829). Larger louvers will require field assembly of multiple sections by others . Larger louvers may require structural support by others

Available Options. Continuous Blade Construction (concealed mullions). Extended Sill (loose) 14 GA. Aluminum. Blank-off Panels: Aluminum or Galvanized, Insulated or Non-Insulated. Formed Flange and Mounting Angle up to 4". Birdscreen: Aluminum or Galvanized. Insect Screen: Aluminum or Bronze. Finishes: Prime Coat, Baked Enamel, Duranar , Duranar XL. Anodized Finishes: Clear or Colour (Light Bronze, Medium Bronze, Dark Bronze, Black)

Superior Air Performance

VISIBLE VERTICAL MULLION (STANDARD) CB: CONTINUOUS BLADE (OPTION)

HORIZONTAL SECTIONMULTI-SECTION ASSEMBLY

VERTICAL SECTIONSTANDARD ASSEMBLY

"A" Mounting Shownfor other mountings see 228900

1.5” "B" Mounting Shownfor other mountingssee 228900

®

E.H. Price Limited certifies that the JE443 shown herein is licensed to bear the AMCA Seal. The ratings shown are based on tests and pro-cedures performed in accordance with AMCA Publication 511 and comply with the requirements of the AMCA Certified Ratings Program The AMCA Certified Seal applies to air performance ratings and water penetration ratings

© Copyright E.H. Price Limited 2010. 237944 - REV 0 - SHEET 1 OF 1 - January 2006

QTY OPTIONS

PROJECT CUSTOMER

ARCHITECT ENGINEER

SPEC. SYMBOL DATE

LOUVER SIZEWIDTH HEIGHT

OPENING SIZEWIDTH HEIGHT


TAG UNITS: IMPERIAL METRIC


ZE439 FIXED BLADE LOUVER

237945 - REV 0 - SHEET 1 OF 1 - January 2006



Standard ConstructionFrame. 4" x .081"(101 x 2.1) Extruded Aluminum (6063-T5). Drainable HeadBlades. Z Style Blades, .081"(2.1) Extruded Aluminum (6063-T5) 390 blade angle, 5"(127) blade spacingFinishes. MILLMinimum Section Size. 9" W x 9 1/2" H (229 x 241)Maximum Section Size. One piece construction 72" W x 120" H (1829 x 3048) or 120" W x 72" H (3048 x 1829). Larger louvers will require field assembly of multiple sections by others . Larger louvers may require structural support by others


®

E.H. Price Limited certifies that the ZE439 shown herein is licensed to bear the AMCA Seal. The ratings shown are based on tests and pro-cedures performed in accordance with AMCA Publicati on 511 and comply with the requirements of the AMCA Certified Ratings Program The AMCA Certified Seal applies to air performance ratings and water penetration ratings



QTY OPTIONS

PROJECT CUSTOMER

ARCHITECT ENGINEER

SPEC. SYMBOL DATE





ZE445 FIXED BLADE LOUVER




Standard ConstructionFrame. 4" x .081"(101 x 2.1) Extruded Aluminum (6063-T5)Blades. Z Style Blades, .081"(2.1) Extruded Aluminum (6063-T5) 450 blade angle, 5"(127) blade spacingFinishes. MILLMinimum Section Size. 9" W x 10 1/2" H (229 x 267)Maximum Section Size. One piece construction 72" W x 120" H (1829 x 3048) or 120" W x 72" H (3048 x 1829). Larger louvers will require field assembly of multiple sections by others . Larger louvers may require structural support by others


®

E.H. Price Limited certifies that the ZE445 shown herein is licensed to bear the AMCA Seal. The ratings shown are based on tests and pro-cedures performed in accordance with AMCA Publication 511 and comply with the requirements of the AMCA Certified Ratings Program The AMCA Certified Seal applies to air performance ratings and water penetration ratings



QTY OPTIONS

PROJECT CUSTOMER

ARCHITECT ENGINEER

SPEC. SYMBOL DATE





DE439 FIXED BLADE LOUVER




Standard ConstructionFrame. 4" x .081"(101 x 2.1) Extruded Aluminum (6063-T5)Blades. Drainable Style Blades, .081"(2.1) Extruded Aluminum (6063-T5) 390 blade angle, 5"(127) blade spacingFinishes. MILLMinimum Section Size. 9" W x 9 1/2" H (229 x 241)Maximum Section Size. One piece construction 72" W x 120" H (1829 x 3048) or 120" W x 72" H (3048 x 1829). Larger louvers will require field assembly of multiple sections by others . Larger louvers may require structural support by others


®

E.H. Price Limited certifies that the DE439 shown herein is licensed to bear the AMCA Seal. The ratings shown are based on tests and pro-cedures performed in accordance with AMCA Publication 511 and comply with the requirements of the AMCA Certified Ratings Program The AMCA Certified Seal applies to air performance ratings and water penetration ratings



QTY OPTIONS

PROJECT CUSTOMER

ARCHITECT ENGINEER

SPEC. SYMBOL DATE





DE635 LOUVER FIXED BLADE

237947 - REV 0 - SHEET 1 OF 1 - December 2009



Standard ConstructionFrame. 6" x .081"(152 x 2) Extruded Aluminum (6063-T5)Blades. Drainable Style Blades, .081"(2.1) Extruded Aluminum (6063-T5) Blades 350 blade angle, 4.5"(115) blade spacingFinishes. MILLMinimum Section Size. 9" W x 10 1/8" H (229 x 257)Maximum Section Size. One piece construction 72" W x 120" H (1829 x 3048) or 120" W x 72" H (3048 x 1829). Larger louvers will require field assembly of multiple sections by others . Larger louvers may require structural support by others


®

E.H. Price Limited certifies that the DE635 shown herein is licensed to bear the AMCA Seal. The ratings shown are based on tests and pro-cedures performed in accordance with AMCA Publication 511 and comply with the requirements of the AMCA Certified Ratings Program The AMCA Certified Seal applies to air performance ratings and water penetration ratings

VISIBLE VERTICAL MULLION (STANDARD)

CB: CONTINUOUS BLADE (OPTION)


QTY OPTIONS

PROJECT CUSTOMER

ARCHITECT ENGINEER

SPEC. SYMBOL DATE





NJE2 FIXED BLADE LOUVER

221956- REV 0 - SHEET 1 OF 1 - January 2006

Standard Construction

Frame 2" x .063"(50 x 1.6) Extruded Aluminum (6063-T5) BladesJ Style Blades, .063"(1.6) Extruded Aluminum (6063-T5) 300 blade angle, approximately 2"(50) blade spacing Finishes MILL Minimum Size 7" W x 5 7/16" H (178 x 138) Maximum Size 60" W x 120" H (1524 x 3048)* One piece construction

Available Options. Extended Sill (loose) 14 GA. Aluminum. Blank-off Panels: Aluminum or Galvanized, Insulated or Non-Insulated. Formed Flange and Mounting Angle up to 4". Birdscreen: Aluminum or Galvanized. Insect Screen: Aluminum or Bronze. Finishes: Prime Coat, Baked Enamel, Duranar , Duranar XL. Anodized Finishes: Clear or Colour (Light Bronze, Medium Bronze, Dark Bronze, Black)


VERTICAL SECTION

SILL

HEAD

EXTERIOR


QTY OPTIONS

PROJECT CUSTOMER

ARCHITECT ENGINEER

SPEC. SYMBOL DATE





NSE1 FIXED BLADE LOUVER



Frame 1.5" x .100"(38 x 2.5) Extruded Aluminum (6063-T5) Blades.063"(1.6) Extruded Aluminum (6063-T5) 1"(25) blade spacing

Finishes MILL Minimum Size 6" W x 5 13/16" H (152 x 148) Maximum Size 72" W x 72" H (1829 x 1829)




QTY OPTIONS

PROJECT CUSTOMER

ARCHITECT ENGINEER

SPEC. SYMBOL DATE





QA645 FORMED ALUMINUM ACOUSTIC LOUVER



Frame 6"(152) Formed 12 GA AluminumBlades Formed 12 GA Aluminum at a 450 angle, 6"(152) blade spacing Finishes MILL Minimum Size 18" W x 10 13/16" H (457 x 275) Maximum Size 72" W x 120" H (1829 x 3048)


Free-Field Noise Reduction in Decibels



QTY OPTIONS

PROJECT CUSTOMER

ARCHITECT ENGINEER

SPEC. SYMBOL DATE



TAG

Selected 1/3 Octave Bands Center Frequency Hz

63 125 250 500 1000 2000 4000 8000 13 8 10 13 21 25 22 23

UNITS: IMPERIAL METRIC


QA1245FORMED ALUMINUM ACOUSTIC LOUVER



Frame 12"(304) Formed 12 GA Aluminum Blades Formed 12 GA Aluminum at a 450 angle, 6"(152) blade spacing Finishes MILL Minimum Size 18" W x 93/4" H (457 x 502) Maximum Size 72" W x 120" H (1829 x 3048) Available Options. Extended Sill (loose) 14 GA. Aluminum. Blank-off Panels: Aluminum or Galvanized, Insulated or Non-Insulated. Formed Flange and Mounting Angle up to 4". Birdscreen: Aluminum or Galvanized. Insect Screen: Aluminum or Bronze. Finishes: Prime Coat, Baked Enamel, Duranar , Duranar XL. Anodized Finishes: Clear or Colour (Light Bronze, Medium Bronze, Dark Bronze, Black)

Free-Field Noise Reduction in Decibels



QTY OPTIONS

PROJECT CUSTOMER

ARCHITECT ENGINEER

SPEC. SYMBOL DATE



TAG

Selected 1/3 Octave Bands Center Frequency Hz

63 125 250 500 1000 2000 4000 8000 16 13 15 18 16 18 18 21




Frame5" x .081"(127 x 2.1) Extruded Aluminum (6063-T5) BladesDrainable Style Blades, .081"(2.1) Extruded Aluminum (6063-T5) at a 450 blade angle, 2"(51) blade spacing Finishes MILL Minimum Size 8" W x 14" H (203 x 356) Maximum Size 72" W x 120" H (829 x 3048)* One dimension (W or H) must not exceed 72"(1829)



RSE5 RAINSTORM LOUVER


QTY OPTIONS

PROJECT CUSTOMER

ARCHITECT ENGINEER

SPEC. SYMBOL DATE





MCJE443 LOUVERED PENTHOUSE



Frame 4" x .081"(102 x 2.1) Extruded Aluminum (6063-T5) Blades J Style Blades, .081"(2.1) Extruded Aluminum (6063-T5) 430 blade angle, 4"(102) blade spacing Finishes MILL PenthouseSize Limits: MAX. INSIDE CURB DIMENSION (LENGTH OR WIDTH) 108”[2743] MAX. HEIGHT ABOVE CURB 70.65”[1795] MIN. INSIDE CURB DIMENSION (LENGTH OR WIDTH) 16”[406] MIN. HEIGHT ABOVE CURB 15.65”[398]PENTHOUSE HEIGHT = MULTIPLES OF 5”[127] + 15.65”[398]

Available Options. Extended Sill (loose) 14 GA. Aluminum. Variety of Bird & Insect Screens. Wide variety of Finishes including: Baked Enamel, Duranar & Duranar XL, Clear & Colour Anodize. Roof Curb* Select from PRICE Colour Chart or provide Colour sample to match



QTY OPTIONS

PROJECT CUSTOMER

ARCHITECT ENGINEER

SPEC. SYMBOL DATE

LENGTH WIDTH HEIGHTTAG INSIDE CURB DIMENSION UNITS: IMPERIAL

METRIC


MCZE439 LOUVERED PENTHOUSE



Frame 4" x .081"(102 x 2.1) Extruded Aluminum (6063-T5) Blades Z Style Blades, .081"(2.1) Extruded Aluminum (6063-T5) at a 390 blade angle with approximately 4"(102) blade spacing Finishes MILL Penthouse Size LimitsMAX. INSIDE CURB DIMENSION (LENGTH OR WIDTH) 108”[2743] MAX. HEIGHT ABOVE CURB 73.06”[1754] MIN. INSIDE CURB DIMENSION (LENGTH OR WIDTH) 16”[406] MIN. HEIGHT ABOVE CURB 13.06”[331]PENTHOUSE HEIGHT = MULTIPLES OF 4”[102] + 13.06”[331]




QTY OPTIONS

PROJECT CUSTOMER

ARCHITECT ENGINEER

SPEC. SYMBOL DATE


METRIC


MCZE445 LOUVERED PENTHOUSE



Frame 4" x .081"(102 x 2.1) Extruded Aluminum (6063-T5) Blades Z Style Blades, .081"(2.1) Extruded Aluminum (6063-T5) at a 450 blade angle with approximately 4"(102) blade spacing Finishes MILL Penthouse Size Limits MAX. INSIDE CURB DIMENSION (LENGTH OR WIDTH) 108”[2743] MAX. HEIGHT ABOVE CURB 70.72”[1796] MIN. INSIDE CURB DIMENSION (LENGTH OR WIDTH) 16”[406] MIN. HEIGHT ABOVE CURB 15.72”[399]PENTHOUSE HEIGHT = MULTIPLES OF 5”[127] + 15.72”[399]




QTY OPTIONS

PROJECT CUSTOMER

ARCHITECT ENGINEER

SPEC. SYMBOL DATE


METRIC


MCDE439 LOUVERED PENTHOUSE



Frame 4" x .081"(102 x 2.1) ExtrudedAluminum (6063-T5) Blades Drainable Style Blades, .081"(2.1) Extruded Aluminum (6063-T5) at a 390 blade angle with approximately 4"(102) blade spacing Finishes MILL Penthouse Size Limits MAX. INSIDE CURB DIMENSION (LENGTH OR WIDTH) 108”[2743] MAX. HEIGHT ABOVE CURB 73.06”[1754] MIN. INSIDE CURB DIMENSION (LENGTH OR WIDTH) 16”[406] MIN. HEIGHT ABOVE CURB 13.06”[331]PENTHOUSE HEIGHT = MULTIPLES OF 4”[102] + 13.06”[331]

Available Options. Extended Sill (loose) 14 GA. Aluminum. Variety of Bird & Insect Screens. Wide variety of Finishes including: Baked Enamel, Prime Coat, Duranar & Duranar XL, Clear & Colour Anodize. Roof Curb* Select from PRICE Colour Chart or provide Colour sample to match



QTY OPTIONS

PROJECT CUSTOMER

ARCHITECT ENGINEER

SPEC. SYMBOL DATE


METRIC


MCDE635 LOUVERED PENTHOUSE



Frame 6" x .081"(152 x 2.1) Extruded Aluminum (6063-T5) Blades Drainable Style Blades, .081"(2.1) Extruded Aluminum (6063-T5) at a 350 blade angle with approximately 4.5"(114) blade spacing Finishes MILL Penthouse Size LimitsMAX. INSIDE CURB DIMENSION (LENGTH OR WIDTH) 104”[2642] MAX. HEIGHT ABOVE CURB 74.43”[1890] MIN. INSIDE CURB DIMENSION (LENGTH OR WIDTH) 16”[406] MIN. HEIGHT ABOVE CURB 15.93”[405]PENTHOUSE HEIGHT = MULTIPLES OF 4.50”[114] + 15.93”[405]




QTY OPTIONS

PROJECT CUSTOMER

ARCHITECT ENGINEER

SPEC. SYMBOL DATE


METRIC


BCJE443 LOUVERED PENTHOUSE



Frame 4" x .081"(102 x 2.1) Extruded Aluminum (6063-T5) Blades Z Style Blades, .081"(2.1) Extruded Aluminum (6063-T5) at a 430 blade angle with approximately 4"(102) blade spacing Finishes MILL Penthouse Size LimitsMAX. INSIDE CURB DIMENSION [LENGTH] 240”[6096] MAX. INSIDE CURB DIMENSION [WIDTH] 120”[3048] MAX. HEIGHT ABOVE CURB 72”[1829] MIN. INSIDE CURB DIMENSION (LENGTH OR WIDTH) 12”[305] MIN. HEIGHT ABOVE CURB 10½”[267] Available Options. Extended Sill (loose) 14 GA. Aluminum. Variety of Bird & Insect Screens. Wide variety of Finishes including: Baked Enamel, Prime Coat, Duranar & Duranar XL, Clear & Colour Anodize. Roof Curb* Select from PRICE Colour Chart or provide Colour sample to match



QTY OPTIONS

PROJECT CUSTOMER

ARCHITECT ENGINEER

SPEC. SYMBOL DATE


METRIC


BCZE439 LOUVERED PENTHOUSE



Frame 4" x .081"(102 x 2.1) Extruded Aluminum (6063-T5) Blades Z Style Blades, .081"(2.1) Extruded Aluminum (6063-T5) at a 390 blade angle with approximately 4"(102) blade spacing Finishes MILL Penthouse Size LimitsMAX. INSIDE CURB DIMENSION [LENGTH] 240”[6096] MAX. INSIDE CURB DIMENSION [WIDTH] 120”[3048] MAX. HEIGHT ABOVE CURB 72”[1829] MIN. INSIDE CURB DIMENSION (LENGTH OR WIDTH) 12”[305] MIN. HEIGHT ABOVE CURB 9½”[241]




QTY OPTIONS

PROJECT CUSTOMER

ARCHITECT ENGINEER

SPEC. SYMBOL DATE


METRIC


BCZE445 LOUVERED PENTHOUSE



Frame 4" x .081"(102 x 2.1) Extruded Aluminum (6063-T5) Blades Z Style Blades, .081"(2.1) Extruded Aluminum (6063-T5) at a 450 blade angle with approximately 4"(102) blade spacing Finishes MILL Penthouse Size Limits MAX. INSIDE CURB DIMENSION [LENGTH] 240”[6096] MAX. INSIDE CURB DIMENSION [WIDTH] 120”[3048] MAX. HEIGHT ABOVE CURB 72”[1829] MIN. INSIDE CURB DIMENSION (LENGTH OR WIDTH) 12”[305] MIN. HEIGHT ABOVE CURB 10½”[267]




QTY OPTIONS

PROJECT CUSTOMER

ARCHITECT ENGINEER

SPEC. SYMBOL DATE


METRIC


BCDE439 LOUVERED PENTHOUSE

243560 - REV 0 - SHEET 1 OF 1- January 2006


Frame 4" x .081"(102 x 2.1) Extruded Aluminum (6063-T5) Blades Drainable Style Blades, .081"(2.1) Extruded Aluminum (6063-T5) at a 390 blade angle with approximately 4"(102) blade spacing Finishes MILL Penthouse Size Limits MAX. INSIDE CURB DIMENSION [LENGTH] 240”[6096] MAX. INSIDE CURB DIMENSION [WIDTH] 120”[3048] MAX. HEIGHT ABOVE CURB 72”[1829] MIN. INSIDE CURB DIMENSION (LENGTH OR WIDTH) 12”[305] MIN. HEIGHT ABOVE CURB 9½”[241]




QTY OPTIONS

PROJECT CUSTOMER

ARCHITECT ENGINEER

SPEC. SYMBOL DATE


METRIC


BCDE635 LOUVERED PENTHOUSE



Frame 6" x .081"(152 x 2.1) Extruded Aluminum (6063-T5) Blades Drainable Style Blades, .081"(2.1) Extruded Aluminum (6063-T5) at a 350 blade angle with approximately 4.5"(114) blade spacing Finishes MILL Penthouse Size Limits MAX. INSIDE CURB DIMENSION [LENGTH] 240”[6096] MAX. INSIDE CURB DIMENSION [WIDTH] 120”[3048] MAX. HEIGHT ABOVE CURB 72”[1829] MIN. INSIDE CURB DIMENSION (LENGTH OR WIDTH) 12”[305] MIN. HEIGHT ABOVE CURB 10.13”[257]




QTY OPTIONS

PROJECT CUSTOMER

ARCHITECT ENGINEER

SPEC. SYMBOL DATE


METRIC

Mounting Method

A(Standard)

Mounting Hardwareby others

Louver with Flat Flange

Louver with Mounting AnglesAngles shipped loose and fitted in fieldby others. Mounting holes not included.

Screws included for mountingangles to louvers.

Louver with Masonary AnchorsMasonary straps welded to the louver jambs on

16” (406) centers. 2” x 10” (50 x 254)

Louver with Pressure Relief FastenersFastener size, spacing and quantity varie with

pressure to be relieved and louver size.Recommended release pressure: 25 psf

B

C

D

PressureRelief

Do Not Caulk

Caulking(by others)

Caulking(by others)

Caulking(by others)


Submittal Sheet

QTY OPTIONS

PROJECT CUSTOMER

ARCHITECT ENGINEER

SPEC. SYMBOL DATE

LOUVER SIZEW (IN.) H (IN.)

OPENING SIZEW (IN.) H (IN.)


MOUNTING METHOD


Submittal Sheet

QTY OPTIONS

PROJECT CUSTOMER

ARCHITECT ENGINEER

SPEC. SYMBOL DATE




INSULATED BLANK-OFF PANELS WITH THERMAL BREAK


Submittal Sheet

QTY OPTIONS

PROJECT CUSTOMER

ARCHITECT ENGINEER

SPEC. SYMBOL DATE




PENTHOUSE CURB

Item Quan Type SectQuan

Location orDesignation

Louver SizeW x H

Section SizeW x H

Opening SizeW x H

LOUVER SCHEDULE

METHOD OF INSTALLATION

FINISH SCREEN NOTES

Mill None PrimeCoat InteriorMounting BakedEnamel ExteriorMounting Colour: 1/2"MeshBirdScreen Duranar 3/4"MeshBirdScreen DuranarXL 1"MeshBirdScreen Colour:____________ Other____________ ClearAnodize* WithFoldedFrame LtBronzeAnodize* Aluminum MedBronzeAnod.* GalvSteel DkBronzeAnod.* Bronze BlackAnodize* Other____________ *Aluminumonly

METHODA-Installationmethodbyothers

METHODB-InstallationwithFlatFlange At: Head____________Sill____________ Jamb____________ On: Exterior____________or Interior____________ Flangewidth:____________ Mountingholesnotincluded

METHODC-InstallationwithAngleFlange At: Head____________Sill____________ Jamb____________ On: Exterior____________orInterior____________ AngleExtension:____________ Mountingholesnotincluded- Anglesshippedloose;fieldmounting

METHODD-InstallationwithMasonryStrapAnchor2"x10"(51x254)Masonrystrapanchorweldedtojamboflouver

Submittals


Description Submittal Number Date

Page Number:

Effective Date:

Supersedes:

Accessories / Installation

Accessories

Mounting Methods 239450 January 1 / 06

Formed Metal Sill 239528 January 1 / 06

Standard / Multi-Section Insulated 239531 January 1 / 06Blank-offs with Thermal BreaksVertical Splicing

Installation

Field Installation Multi-Section 239533 January 1 / 06with Visible Vertical Mullion

Field Installation Multi-Section 239532 January 1 / 06with Continuous Blade

Field Assembly Multi-Section 239530 January 1 / 06Installation Screens / Blank-offs Vertical Splicing

Field Installation Multi-Section 239529 January 1 / 06Label / Section Assembly Sequence

ACI-1Jan.1 / 06 Initial


MOUNTING METHODS

239450 - REV 0 - SHEET 1 OF 1 - 2003/03/24


FORMED METAL SILL

239528 - REV 0 - SHEET 1 OF 1 - 2003/05/05


FIELD INSTALLATIONMULTI-SECTION WITH VISIBLE VERTICAL MULLION


FIELD INSTALLATIONMULTI-SECTION WITH CONTINUOUS BLADE


FIELD ASSEMBLYMULTI-SECTION INSTALLATIONSCREENS / BLANK-OFFSVERTICAL SPLICING


FIELD INSTALLATION MULTI-SECTIONLABEL / SECTION ASSEMBLYSEQUENCE

4

12 12 11

11

10

12 1210

79 95

8 8

• Canadian Head Office, Laboratory & Manufacturing Facilities in Winnipeg, Manitoba

• Sales Offices or Representation in all major Canadian cities

638 Raleigh Street

Winnipeg, Manitoba Canada R2K 3Z9

Ph: 204.669.4220 Fax: 204.663.2715

Product Improvement is a continuing endeavor at Price. Therefore, specifications are subject to change without notice. Consult your Price sales representative for current specifications or more detailed information.

The founding principles of our company have never changed – business integrity, first-class service and a commitment topeople. Price manufacturing endeavors arose from our belief that we could supply superior products and services at areasonable price. Our mission is to become the worldwide supplier of preference for air distribution products and services. You can rely on Price – our products and services – with confidence.

Warranty: The Company warrants and guarantees that all goods within this catalogue that have been manufactured by the Company have been manufactured in accordance with the specifications published herein and will be free from defects in material and workmanship for a period of twelve (12) months from the date of Bill of Lading issued by the Company. The Company will replace defective product at its option, but will not be responsible for labor or material charges in replacing product or consequential damages. Any installation not conforming with the Company's specifications, manuals, bulletins or instructions or any misuse or any modification not authorized by the Company voids this warranty. This warranty is in lieu of all Provincial, State, and Federal statutory warranties and the conditions herein are in substitution and replacement of such warranties, statutory or otherwise.

Your Local Price Representative:

Price Louver Products

A I R D I S T R I B U T I O N P R O D U C T S F O R W O R L D C L A S S C I T I E S

w w w . e h p r i c e s a l e s . c o m

E.H. Price Sales, a division of E.H. Price Limited. Price® is a registered trademark of E.H. Price Limited. © 2010.

Lithographed in Canada 2010

louvers catalog

Documents

require additional

computer assisted

corner cover

astm designations

horizontal

field noise

project architect

air volume