lte mini-pim and antenna installation guide · pdf filetitle: lte mini-pim and antenna...

LTE Mini-PIM and Antenna Installation Guide

Modified: 2017-08-14

Copyright © 2017, Juniper Networks, Inc.

Juniper Networks, Inc.1133 InnovationWaySunnyvale, California 94089USA408-745-2000www.juniper.net

Copyright © 2017 Juniper Networks, Inc. All rights reserved.

Juniper Networks, the Juniper Networks logo, Juniper, and Junos are registered trademarks of Juniper Networks, Inc. and/or its affiliates inthe United States and other countries. All other trademarks may be property of their respective owners.

Juniper Networks assumes no responsibility for any inaccuracies in this document. Juniper Networks reserves the right to change, modify,transfer, or otherwise revise this publication without notice.

LTE Mini-PIM and Antenna Installation GuideCopyright © 2017 Juniper Networks, Inc. All rights reserved.

The information in this document is current as of the date on the title page.

YEAR 2000 NOTICE

Juniper Networks hardware and software products are Year 2000 compliant. Junos OS has no known time-related limitations through theyear 2038. However, the NTP application is known to have some difficulty in the year 2036.

ENDUSER LICENSE AGREEMENT

The Juniper Networks product that is the subject of this technical documentation consists of (or is intended for use with) Juniper Networkssoftware. Use of such software is subject to the terms and conditions of the End User License Agreement (“EULA”) posted athttp://www.juniper.net/support/eula/. By downloading, installing or using such software, you agree to the terms and conditions of thatEULA.

Copyright © 2017, Juniper Networks, Inc.ii

http://www.juniper.net/support/eula/

Table of Contents

About the Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ix

Documentation and Release Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ix

Supported Platforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ix

Documentation Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ix

Documentation Feedback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xi

Requesting Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xii

Self-Help Online Tools and Resources . . . . . . . . . . . . . . . . . . . . . . . . . . . xii

Opening a Case with JTAC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xii

Part 1 Overview

Chapter 1 LTE Mini-Physical Interface Module (Mini-PIM) . . . . . . . . . . . . . . . . . . . . . . . . 3

LTE Mini-Physical Interface Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

LTE Mini-Physical Interface Module LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

LTE Mini-Physical Interface Module Hardware Specifications . . . . . . . . . . . . . . . . . 7

Part 2 Installation

Chapter 2 LTE Mini-PIM Installation and Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Installing the LTE Mini-PIM in a SRX Series Services Gateway . . . . . . . . . . . . . . . . 11

Configuring the LTE Mini-PIM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Chapter 3 LTE Mini-PIM Firmware Upgrade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Upgrading the Mini-PIM Firmware Using the CLI . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Upgrading the Modem Firmware by Using OTA Upgrade . . . . . . . . . . . . . . . . . . . . 19

iiiCopyright © 2017, Juniper Networks, Inc.

List of Figures

Part 1 Overview


Figure 1: LTE Mini-PIM Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Figure 2: LTE Mini-PIM LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Part 2 Installation

Chapter 2 LTE Mini-PIM Installation and Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Figure 3: Installing the LTE Mini-PIM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Figure 4: Attaching the Antennas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Figure 5: Mounting the Antennas on a Rack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Figure 6: Mounting the Antennas on aWall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

vCopyright © 2017, Juniper Networks, Inc.

List of Tables

About the Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ix

Table 1: Notice Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . x

Table 2: Text and Syntax Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . x

Part 1 Overview


Table 3: LTE Mini-PIM Front Panel Components . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Table 4: Specifications for the LTE Mini-PIM Antenna . . . . . . . . . . . . . . . . . . . . . . . 4

Table 5: Antenna Base Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Table 6: LTE Mini-PIM Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Table 7: LTE Mini-PIM LED States . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Table 8: LTE Mini-PIM Hardware Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

viiCopyright © 2017, Juniper Networks, Inc.

About the Documentation

• Documentation and Release Notes on page ix

• Supported Platforms on page ix

• Documentation Conventions on page ix

• Documentation Feedback on page xi

• Requesting Technical Support on page xii

Documentation and Release Notes

To obtain the most current version of all Juniper Networks®technical documentation,

see the product documentation page on the Juniper Networks website at

http://www.juniper.net/techpubs/.

If the information in the latest release notes differs from the information in the

documentation, follow the product Release Notes.

Juniper Networks Books publishes books by Juniper Networks engineers and subject

matter experts. These books go beyond the technical documentation to explore the

nuances of network architecture, deployment, and administration. The current list can

be viewed at http://www.juniper.net/books.

Supported Platforms

For the features described in this document, the following platforms are supported:

• SRX550M

• SRX345

• SRX340

• SRX320

Documentation Conventions

Table 1 on page x defines notice icons used in this guide.

ixCopyright © 2017, Juniper Networks, Inc.

http://www.juniper.net/techpubs/

http://www.juniper.net/books

http://www.juniper.net/techpubs/en_US/release-independent/junos/information-products/pathway-pages/hardware/SRX550/srx550-hm-index.html

http://www.juniper.net/techpubs/en_US/release-independent/junos/information-products/pathway-pages/hardware/srx345/index.html



Table 1: Notice Icons

DescriptionMeaningIcon

Indicates important features or instructions.Informational note

Indicates a situation that might result in loss of data or hardware damage.Caution

Alerts you to the risk of personal injury or death.Warning

Alerts you to the risk of personal injury from a laser.Laser warning

Indicates helpful information.Tip

Alerts you to a recommended use or implementation.Best practice

Table 2 on page x defines the text and syntax conventions used in this guide.

Table 2: Text and Syntax Conventions

ExamplesDescriptionConvention

To enter configuration mode, type theconfigure command:

user@host> configure

Represents text that you type.Bold text like this

user@host> show chassis alarms

No alarms currently active

Represents output that appears on theterminal screen.

Fixed-width text like this

• A policy term is a named structurethat defines match conditions andactions.

• Junos OS CLI User Guide

• RFC 1997,BGPCommunities Attribute

• Introduces or emphasizes importantnew terms.

• Identifies guide names.

• Identifies RFC and Internet draft titles.

Italic text like this

Configure themachine’s domain name:

[edit]root@# set system domain-namedomain-name

Represents variables (options for whichyou substitute a value) in commands orconfiguration statements.

Italic text like this

Copyright © 2017, Juniper Networks, Inc.x


Table 2: Text and Syntax Conventions (continued)

ExamplesDescriptionConvention

• To configure a stub area, include thestub statement at the [edit protocolsospf area area-id] hierarchy level.

• Theconsoleport is labeledCONSOLE.

Represents names of configurationstatements, commands, files, anddirectories; configurationhierarchy levels;or labels on routing platformcomponents.

Text like this

stub <default-metricmetric>;Encloses optional keywords or variables.< > (angle brackets)

broadcast | multicast

(string1 | string2 | string3)

Indicates a choice between themutuallyexclusive keywords or variables on eitherside of the symbol. The set of choices isoften enclosed in parentheses for clarity.

| (pipe symbol)

rsvp { # Required for dynamicMPLS onlyIndicates a comment specified on thesame lineas theconfiguration statementto which it applies.

# (pound sign)

community namemembers [community-ids ]

Encloses a variable for which you cansubstitute one or more values.

[ ] (square brackets)

[edit]routing-options {static {route default {nexthop address;retain;

}}

}

Identifies a level in the configurationhierarchy.

Indention and braces ( { } )

Identifies a leaf statement at aconfiguration hierarchy level.

; (semicolon)

GUI Conventions

• In the Logical Interfaces box, selectAll Interfaces.

• To cancel the configuration, clickCancel.

Representsgraphicaluser interface(GUI)items you click or select.

Bold text like this

In the configuration editor hierarchy,select Protocols>Ospf.

Separates levels in a hierarchy of menuselections.

> (bold right angle bracket)

Documentation Feedback

We encourage you to provide feedback, comments, and suggestions so that we can

improve the documentation. You can provide feedback by using either of the following

methods:

• Online feedback rating system—On any page of the Juniper Networks TechLibrary site

athttp://www.juniper.net/techpubs/index.html, simply click the stars to rate thecontent,

and use the pop-up form to provide us with information about your experience.

Alternately, you can use the online feedback form at

http://www.juniper.net/techpubs/feedback/.

xiCopyright © 2017, Juniper Networks, Inc.


http://www.juniper.net/techpubs/index.html

http://www.juniper.net/techpubs/feedback/

• E-mail—Sendyourcommentsto [email protected]. Includethedocument

or topic name, URL or page number, and software version (if applicable).

Requesting Technical Support

Technical product support is available through the JuniperNetworksTechnicalAssistance

Center (JTAC). If you are a customer with an active J-Care or Partner Support Service

support contract, or are covered under warranty, and need post-sales technical support,

you can access our tools and resources online or open a case with JTAC.

• JTAC policies—For a complete understanding of our JTAC procedures and policies,

review the JTAC User Guide located at

http://www.juniper.net/us/en/local/pdf/resource-guides/7100059-en.pdf.

• Product warranties—For product warranty information, visit

http://www.juniper.net/support/warranty/.

• JTAC hours of operation—The JTAC centers have resources available 24 hours a day,

7 days a week, 365 days a year.

Self-Help Online Tools and Resources

For quick and easy problem resolution, Juniper Networks has designed an online

self-service portal called the Customer Support Center (CSC) that provides youwith the

following features:

• Find CSC offerings: http://www.juniper.net/customers/support/

• Search for known bugs: http://www2.juniper.net/kb/

• Find product documentation: http://www.juniper.net/techpubs/

• Find solutions and answer questions using our Knowledge Base: http://kb.juniper.net/

• Download the latest versions of software and review release notes:

http://www.juniper.net/customers/csc/software/

• Search technical bulletins for relevant hardware and software notifications:

http://kb.juniper.net/InfoCenter/

• Join and participate in the Juniper Networks Community Forum:

http://www.juniper.net/company/communities/

• Open a case online in the CSC Case Management tool: http://www.juniper.net/cm/

Toverify serviceentitlementbyproduct serial number, useourSerialNumberEntitlement

(SNE) Tool: https://tools.juniper.net/SerialNumberEntitlementSearch/

Opening a Casewith JTAC

You can open a case with JTAC on theWeb or by telephone.

• Use the Case Management tool in the CSC at http://www.juniper.net/cm/.

• Call 1-888-314-JTAC (1-888-314-5822 toll-free in the USA, Canada, and Mexico).

Copyright © 2017, Juniper Networks, Inc.xii


mailto:[email protected]?subject=

http://www.juniper.net/us/en/local/pdf/resource-guides/7100059-en.pdf

http://www.juniper.net/support/warranty/

http://www.juniper.net/customers/support/

http://www2.juniper.net/kb/

http://www.juniper.net/techpubs/

http://kb.juniper.net/

http://www.juniper.net/customers/csc/software/

http://kb.juniper.net/InfoCenter/

http://www.juniper.net/company/communities/

http://www.juniper.net/cm/

https://tools.juniper.net/SerialNumberEntitlementSearch/

http://www.juniper.net/cm/

For international or direct-dial options in countries without toll-free numbers, see

http://www.juniper.net/support/requesting-support.html.

xiiiCopyright © 2017, Juniper Networks, Inc.


http://www.juniper.net/support/requesting-support.html

PART 1

Overview

• LTE Mini-Physical Interface Module (Mini-PIM) on page 3

1Copyright © 2017, Juniper Networks, Inc.

CHAPTER 1

LTE Mini-Physical Interface Module(Mini-PIM)

• LTE Mini-Physical Interface Module on page 3

• LTE Mini-Physical Interface Module LEDs on page 6

• LTE Mini-Physical Interface Module Hardware Specifications on page 7

LTEMini-Physical InterfaceModule

The LTE Mini-Physical Interface Module (Mini-PIM) provides wirelessWAN support on

theSRX300SeriesandSRX550HighMemoryServicesGateways.TheMini-PIMcontains

an integratedmodemand operates over 3G and 4G networks. TheMini-PIM supports up

to two SIM cards and can be installed in any of the Mini-PIM slots on the services

gateways.

The Mini-PIM supports the following features:

• Automatic switchover between service providers through dual SIMs

• Storage support for multiple service provider and access point name (APN) profiles

• LTE carrier aggregation

• SIM lock and unlock capability

• Always-on, dial-on-demand, and backupmodes

• Over-the-Air upgrade for modem firmware

Figure 1 on page 3 shows the front panel of the LTE Mini-PIM.

Figure 1: LTEMini-PIM Front Panel

Table 3 on page 4 lists the components on the front panel of the Mini-PIM.


Table 3: LTEMini-PIM Front Panel Components

DescriptionComponent

Two SubMiniature version A (SMA) connectors.Antenna connectors

Mini-USB Type-B port for monitoring and troubleshooting.Mini-USB port

Two slots, SIM1 and SIM2, for inserting the SIM cards. The LTE Mini-PIM supports mini, micro,and nano SIMs. Themini-SIM can be inserted directly in the SIM slot. To insert micro and nanoSIMs, use the SIM adapters supplied with the Mini-PIM. The Mini-PIM is shipped with two SIMadapters.

SIM slots

Indicate the status at a glance. For details on the LED indications, see “LTE Mini-PhysicalInterface Module LEDs” on page 6.

LEDs

The LTE Mini-PIM supports twomulti-band swivel-mount dipole antennas, which can

be rotated 360 °. You can rotate the antennas and select the angle at which the signal

strength is high. Table 4 on page 4 lists the specifications for the antenna.

Table 4: Specifications for the LTEMini-PIM Antenna

ValueSpecification

EDA-2010-4G0R2-A2 (Vendor: MAG.LAYERS)Part number

• 704~960MHz

• 1710~2700MHz

Operating frequency range

5 (maximum)Voltage StandingWave Ratio (VSWR)

50 ohmImpedance

OmnidirectionalRadiation

• 2.45 dBi (704~960MHz)

• 4.51 dBi (1710~2700MHz)

Peak gain

1 WInput power

Linear, verticalPolarization

–4° F (–20° C) to 149° F (65° C)Operating temperature

SMAConnector type

203mmLength

The antenna is connected to the services gateway through themagnetic antenna base.

Table 5 on page 5 lists the specifications for the antenna base.



Table 5: Antenna Base Specifications

ValueSpecification

BS-05SF-174-3M-0102 (Vendor: Chang Hong)Part number

3 mCable length

SMAConnector type

29.50mm x 73mm x 73mmDimensions (H xW x L)

Table 6 on page 5 provides a summary of the different models of the Mini-PIM.

Table 6: LTEMini-PIMModels

Frequency BandOperating RegionModeModel

For LTE:

• Bands 1 through 5, 7, 8, 12, 13, 20, 25, 26, 29, 30,and 41

For 3G (HSPA+):

• Bands 1 through 5, and 8

• North America

• European Union

• LTE

• HSPA+

SRX-MP-LTE-AE

For LTE:

• Bands 1,3, 5, 7, 8, 18, 19, 21, 28, 38, 39, 40, and 41

For 3G (HSPA+):

• Bands 1, 5, 6, 8, 9, and 19

• Asia

• Australia

• LTE

• HSPA+

SRX-MP-LTE-AA

The Mini-PIM can be configured in three modes:

• Always-on—TheMini-PIMconnects to the3G/4Gnetworkafterbooting.Theconnection

is always maintained, as long as there are no network or connectivity problems.

• Dial-on-demand—The Mini-PIM initiates a connection when it receives traffic.

• Backup—The Mini-PIM connects to the 3G/4G network when the primary connection

fails.

The LTE Mini-PIM supports the following wireless standards:

• FCC Part 2

• FCC Part 22

• FCC Part 24, Part 27 and Part 90

• RSS 129 and RSS 133, RSS 130, RSS 199, and RSS 139

• RSS 132 and RSS 133

• EN 301 511 GSM


Chapter 1: LTE Mini-Physical Interface Module (Mini-PIM)

• EN 301 908-1

• EN 301 908-2

• The Certification and Engineering Bureau of Industry Canada (IC)

• Radio Equipment (RE) Directive of the European Union

• GCF

• CTIA-PTCRB

RelatedDocumentation

LTE Mini-Physical Interface Module LEDs on page 6•

• LTE Mini-Physical Interface Module Hardware Specifications on page 7

LTEMini-Physical InterfaceModule LEDs

Figure 2 on page 6 shows the LEDs on the LTE Mini-PIM.

Figure 2: LTEMini-PIM LEDs

g009

650

Table 7 on page 6 lists the LEDs on the LTE Mini-PIM and their indications.

Table 7: LTEMini-PIM LED States

DescriptionLED

Solid green (one bar)—Low signal strength (<= –99 dBm).SIG (Received Signal StrengthIndicator)

Solid green (two bars)—Low signal strength(from –98 dBm to –87 dBm).

Solid green (three bars)—Low signal strength(from –86 dBm to –76 dBm).

Solidgreen (fourbars)—Highsignal strength (>=–75dBm).

Unlit—No signal

Solid green—3G connection is established.3G

Blinking green—Connecting to a 3G network.



Table 7: LTEMini-PIM LED States (continued)

DescriptionLED

Solid green—LTE connection is established.LTE

Blinking green—Connecting to an LTE network.

Solid green—SIM1 is active.SIM1

Solid green—SIM2 is active.SIM2

NOTE: If all the LEDs are blinking, it indicates that firmware updates are inprogress.Donotpoweroff theservicesgatewaybefore theupdatescomplete.


LTE Mini-Physical Interface Module Hardware Specifications on page 7•

LTEMini-Physical InterfaceModule Hardware Specifications

Table 8 on page 7 provides the hardware specifications for the LTE Mini-PIM.

Table 8: LTEMini-PIM Hardware Specifications

ValueDescription

0.80 in. x 3.75 in. x 5.9 in.(2.0 cm x 9.5 cm x 14.5 cm)

Dimensions (H xW x L)

0.23 lb (0.106 kg)Weight

SMAConnector type

Mini-PIMForm factor

32° F through 104° F (0° C through 40° C)Environmental operating temperature

-40° F through 158° F (-40° C through 70° C)Storage temperature

5% to 90% noncondensingRelative humidity


• LTE Mini-Physical Interface Module on page 3

• LTE Mini-Physical Interface Module LEDs on page 6


Chapter 1: LTE Mini-Physical Interface Module (Mini-PIM)

PART 2

Installation

• LTE Mini-PIM Installation and Configuration on page 11

• LTE Mini-PIM Firmware Upgrade on page 17


CHAPTER 2

LTE Mini-PIM Installation andConfiguration

• Installing the LTE Mini-PIM in a SRX Series Services Gateway on page 11

• Configuring the LTE Mini-PIM on page 15

Installing the LTEMini-PIM in a SRX Series Services Gateway

To install the LTE Mini-PIM in a services gateway:

NOTE: You can install only oneMini-PIM in a services gateway. TheMini-PIMcan be installed in any of the Mini-PIM slots on the services gateway.

1. Attachanelectrostaticdischarge (ESD)groundingstrap toyourbarewrist, andconnect

the strap to the grounding point on the back of the services gateway.

2. Poweroff the servicesgatewaybybriefly pressing thePowerbuttonon the frontpanel.

Wait for thePowerLED to turnoff beforeproceeding. Disconnect the services gateway

from the power source.

3. Remove the blank Mini-PIM installed on the services gateway:

a. Loosen the screws on the faceplate of the blank Mini-PIM.

b. Grasp the screws on each side and remove the blank Mini-PIM.

4. Remove the LTE Mini-PIM from the electrostatic bag.

5. Grasp the screws on each side of the Mini-PIM faceplate and align the notches in the

connector at the rear of the Mini-PIM with the notches in the Mini-PIM slot in the

services gateway.

CAUTION: Slide theMini-PIM straight into the slot to avoid damaging thecomponents on the Mini-PIM.


6. Slide the Mini-PIM in until it lodges firmly in the services gateway. See

Figure 3 on page 12.

Figure 3: Installing the LTEMini-PIM

7. Using a 1/8-in. (3-mm) flat-blade (–) screwdriver, tighten the screws on each side of

the Mini-PIM faceplate.

8. Remove the cover from the SIM slot, SIM 1. Insert the SIM card into the SIM slot. You

can use the other slot, SIM 2, for installing a secondary or backup SIM.

9. Replace the cover over the SIM slots.

10. Attach the antennas to the antenna base. Connect the cables from each antenna

base to the SMA connectors on the Mini-PIM. See Figure 4 on page 12.

Figure 4: Attaching the Antennas

g009

653

The antenna base is magnetic and can be attached to the rack directly, if the rack is

metallic. Else, you canmount the antenna base on the rack using the mounting

brackets. See Figure 5 on page 13.



Figure 5: Mounting the Antennas on a Rack


Chapter 2: LTE Mini-PIM Installation and Configuration

NOTE: For SRX320 Services Gateways, which can bemounted on awall,the antennas can bemounted as shown in Figure 6 on page 14.

Figure 6: Mounting the Antennas on aWall

g009

648

(27 .9 cm)

> 11 in.

11. Power on the services gateway.

NOTE: Whena services gateway,with the LTEMini-PIM installed andSIMcard inserted, ispoweredon for the first time, itmight takeup to 10minutesfor theMini-PIM to upgrade themodem firmware for the local LTE carrier.


Configuring the LTE Mini-PIM on page 15•



Configuring the LTEMini-PIM

To configure the Mini-PIM:

NOTE: If a services gatewaywith factory-default settings is poweredonwiththe LTEMini-PIM installed in slot 1, the dialer interface is triggered to dialautomatically. This functionality is applicable only if theMini-PIM is installedin slot 1. If the Mini-PIM is installed in any other slot, then you will need tomanually configure the cl-slot-number/0/0 interface to be associated withthe dialer interface.

1. Configure the dialer pool:

user@host# set interfaces cl-slot-number/0/0 dialer-options pool number priority

number

2. Configure the profile:

user@host# requestmodemwireless create-profile profile-id profile-id

access-point-namel3vpn.corpauthentication-methodchapsip-user-iduser@myvpn.net

sip-password password

3. Activate the SIM:

user@host# set interfaces cl-slot-number/0/0 act-sim sim-slot-number

4. Select the profile and configure the radio access type for the SIM card:

user@host# set interfaces cl-slot-number/0/0 cellular-options sim sim-slot-number

profile-id profile-id

user@host# set interfaces cl-slot-number/0/0 cellular-options sim sim-slot-number

radio-access automatic

NOTE: If a SIM card is installed in the second slot, then select the profileand configure the radio access type for the secondary SIM card as well.

5. Configure the dialer interface:

• Always-Onmode:

user@host# set interfaces dl0 unit 0 family inet negotiate-address

user@host# set interfaces dl0 unit 0 family inet6 negotiate-address

user@host# set interfaces dl0 unit 0 dialer-options pool dialer-pool-number

user@host# set interfaces dl0 unit 0 dialer-options dial-string dial-number


Chapter 2: LTE Mini-PIM Installation and Configuration

user@host# set interfaces dl0 unit 0 dialer-options always-on

• Dial-on-Demandmode:

user@host# set interfaces dl0 unit 0 family inet negotiate-address

user@host# set interfaces dl0 unit 0 family inet filter dialer dialer-filter-name

user@host# set interfaces dl0 unit 0 dialer-options pool dialer-pool-number


• Backupmode:

user@host# set interfaces <interface-name> unit 0 backup-options interface dl0.0



• Upgrading the Mini-PIM Firmware Using the CLI on page 17

• Upgrading the Modem Firmware Though Over-the-Air (OTA) on page 19



CHAPTER 3

LTE Mini-PIM Firmware Upgrade


• Upgrading the Modem Firmware by Using OTA Upgrade on page 19

Upgrading theMini-PIM Firmware Using the CLI

To upgrade the firmware on the Mini-PIM, using the CLI:

NOTE: WhenyouupgradethefirmwareontheMini-PIM, themodemfirmwareis also upgraded.

1. Identify the currently installed firmware version and new firmware version available

for upgrade:

user@host > show system firmware

Part Type Tag Current Available Status version versionFPC 1 PIC 0 MLTE_FW 1 17.2.91 OK Routing Engine 0 RE BIOS 0 3.2 3.2 OK Routing Engine 0 RE BIOS Backup 1 3.2 3.2 OK

a. If the Available Version field in the output does not list any information, it indicates

that the device is not running the latest jfirmware. Proceed to Step 2 to download

and upgrade to the latest jfirmware.

b. If the Available Version field in the output lists the firmware version, proceed to

Step 4.

2. Download the appropriate jfirmware version:

NOTE: Ensure that the jfirmware version is the same as the version of theJunos OS installed on the device. To know the Junos OS version, issue theshow version command.

user@host > request system software add var/tmp/jfirmware-version-signed.tgz


3. Verify the new firmware version available:


The version is displayed under the Available Version field in the output.

4. Upgrade the firmware on the device:

user@host > request system firmware upgrade pic pic-slot pic-slot-number fpc-slot

fpc-slot-number

5. Verify the successful completion of the firmware upgrade. The status should show

Upgraded Successfully.


6. Take the FPC offline and then bring it online:

a. Take the FPC offline:

user@host > request chassis pic pic-slot pic-slot-number fpc-slot fpc-slot-number

offline

b. Verify that the FPC is offline:

user@host > show chassis fpc pic-status fpc-slot-number

Slot 0 Online FPC PIC 0 Online 6xGE,2xGE SFP Base PICSlot 1 Offline FPC

c. Bring the FPC online:

user@host > request chassis pic pic-slot pic-slot-number fpc-slot fpc-slot-number

online

d. Verify that the FPC is online:

user@host > show chassis fpc pic-status fpc-slot-number

Slot 0 Online FPC PIC 0 Online 6xGE,2xGE SFP Base PICSlot 1 Online FPC PIC 0 Online MLTE AA PIC

7. Verify that the firmware is upgraded to the latest version:



Upgrading the Modem Firmware Though Over-the-Air (OTA) on page 19•



Upgrading theModem Firmware by Using OTAUpgrade

Over-the-air (OTA) firmware upgrade enables automatic and timely upgrade ofmodem

firmware when new firmware versions are available. The OTA upgrade can be enabled

or disabled on the 4G/LTE Mini-PIM. OTA upgrade is disabled by default.

1. Enable OTA upgrade status on the LTE Mini-PIM:

user@host > requestmodemwireless fota enable

2. Initiate the firmware upgrade:

user@host > requestmodemwireless upgrade cl-slot number/0/0

3. Verify the firmware upgrade status:

user@host > showmodemwireless firmware cl-slot number/0/0

LTE mPIM firmware details Product name: Junos LTE mPIM Serial number: AG50071852 Hardware version: AcceleratedConcepts/sprite Firmware version: 17.4.3 MAC: 00:00:5e:00:53:61 System uptime: 3430 secondsWireless modem firmware details Modem firmware version: 9999999_9904609_SWI9X30C_02.23.00.00_00_GENERIC_002.018_000 Modem Firmware build date: 22/10/2016 Card type: MC7430 Modem manufacturer: Sierra Wireless, Inc Hardware version: 1.0 Power & Temperature: Normal 3343 mV, Normal 30.00 COTA status State: Enabled New firmware available: NoNumber of SIM: 2Slot of active: 2Status of SIM 1 SIM state: SIM present Modem PIN security status: Disabled SIM status: SIM Okay SIM user operation needed: No Op Retries remaining: 3Status of SIM 2 SIM state: SIM present Modem PIN security status: Disabled SIM status: SIM Okay SIM user operation needed: No Op Retries remaining: 3

4. Check the LTE Mini-PIM connection status:

user@host > showmodemwireless network cl-slot number/0/0

root> show modem wireless network cl-1/0/0LTE Connection details


Chapter 3: LTE Mini-PIM Firmware Upgrade

Connected time: 147 IP: 172.16.52.4 Gateway: 172.16.52.5 DNS: 123.123.123.123 Input bps: 0 Output bps: 0 Bytes Received: 1308 Bytes Transferred: 1164 Packets Received: 10 Packets Transferred: 10Wireless Modem Network Info Current Modem Status: Connected Current Service Status: Normal Current Service Type: PS Current Service Mode: LTE Current Band: B3 Network: UNICOM Mobile Country Code (MCC): 460 Mobile Network Code (MNC): 1 Location Area Code (LAC): 65534 Routing Area Code (RAC): 0 Cell Identification: 4865903 Access Point Name (APN): ctnet Public Land Mobile Network (PLMN): CHN-UNICOM Physical Cell ID (PCI): 333 International Mobile Subscriber Identification (IMSI): **************** International Mobile Equipment Identification (IMEI/MEID): ****************

Integrate Circuit Card Identity (ICCID): 89860114721100697502 Reference Signal Receiving Power (RSRP): -97 Reference Signal Receiving Quality (RSRQ): -16 Signal to Interference-plus-Noise Ratio (SiNR): 0 Signal Noise Ratio (SNR): 0 Energy per Chip to Interference (ECIO): 0





lte mini-pim and antenna installation guide · pdf filetitle: lte mini-pim and antenna...

Documents