HD CCTVMega Pixel 30X ZOOM COLOR CAMERAOPERATION MANUAL

Thank you for choosing our high quality camera.Before attempting to connect operate this unit, please read and follow these instructions.

M180-HZA302-001

These servicing instructions are for use by qualified service personnel only.To reduce the risk of electric shock do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so.

Use Class 2 Power Supply Only

CAUTION

2

CONTENTS

1. CAUTIONS

2. IMPORTANT SAFETY INSTRUCTION

3. FEATURES

4. COMPONENTS

5. NAME AND FUNCTION

6. INSTALLATION

7. DIMENSIONS

8. SPECIFICATION

9. OSD MENU STRUCTURE

3

1. CAUTIONS

1. A regulated DC12V 1A power supply is recommended for use with this camera for the best picture and the most stable operation. An unregulated power supply can cause damage to the camera. When unregulated power supply is applied, product warranty will be out of subject.2. It is recommended that the camera is used with a monitor that has a CCTV quality 75Ω video impedance level. If your monitor is switched to high impedance then please adjust accordingly.3. Do not attempt to disassemble the camera to gain access to the internal components. Refer servicing to your dealer.4. Never face the camera towards the sun or any bright or reflective light, which may cause smear on the picture and possible damage to the Image Sensor.5. Do not remove the serial sticker for the warranty service.6. Do not expose the camera to rain or other types of liquid.7. The apparatus must be connected to a mains socket-outlet with a protective earthing connection.

4

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions;

1. This device may not cause harmful interference.2. This device must accept any interference received, including interference that may cause undesired operation.

NoteThis equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.”

WARNINGThis is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

CautionAny changes or modifications in construction of this devices which are not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

1. CAUTIONS

5

Correct Disposal of This Product(Waste Electrical & Electronic Equipment)

(Applicable in the European Union and other European countries with separate collection systems)

This marking shown on the product or its literature, indicate that it should not be disposed with other household wastes at the end of its working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources.

This product should not be mixed with other commercial wastes purchased this product, or their local government office, for details of where and how they can take item for environmentally safe recycling.

Business users should contact their supplier and check the terms and conditions of the purchase contract.Household users should contact either the retailer where they for disposal.

CAUTIONRISK OF ELECTRIC SHOCK DO NOT OPEN

CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER(OR BACK). NO USER. SERVICING TO QUALIFED SERVICE PERSONNEL.

This symbol is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient mangnitude to constitute a risk of electric shock to persons.

This symbol is intended to alert the user to the presence of important operating and maintenance(servicing) instruction in the literature accompanying the appliance.

2. IMPORTANT SAFETY INSTRUCTION

6

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings. Install in accordance with themanufacturer’s instructions.

8) Do not install near any heat sources such as radiators, heat registers,stoves, or other apparatus (including amplifiers) that produce heat.

9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11) Only use attachments/accessories specified by the manufacturer.

12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13) Unplug this apparatus during lightning storms or when unused for long periods of time.

14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

3. PRECAUTIONS

Do not operate under extreme temperature conditions.Using the camera in temperatures exceeding 50˚C or below -10˚C maylower image quality or cause the camera to malfunction.

Do not operate in high humidity environments.Using the camera in places with high humidity may lessen picture qualitybecause of moisture on the lens.

Do not operate under unsteady lighting.The camera will not work properly in places with great changes in illumination intensity, such as fluorescent lamps.

Do not attempt to disassemble the camera.

Do not drop the camera or subject it to physical shock.It may damage the camera if dropped or subjected to strong impact.

Do not exposed to an intense light source such as direct sunlightIt may damage the CMOS.

Do not exposed the camera to rain or other types of liquids.It may damage the camera.

Do not exposed the camera to radioactivity.It may damage the CMOS.

7

• Exposure to a spotlight or an object emitting strong light may cause smear or blooming.• Ensure that the power source complies with normal specifications before supplying it to the camera.

NOTE

4. FEATURES

1) 1/2.8” Sony CMOS Sensor

2) X30 Optical Zoom

3) 1080P 60fps Resolution

4) WDR (Wide Dynamic Range)

5) DNR (Digital Noise Reduction)

6) LSC (Lens Shading Compensation)

7) DIS (Digital Image Stabilizer)

8) Digital Effect (Mirror, Freeze, Negative)

9) Motion Detection/

10) Privacy Masking

11) Defog

12) Day & Night (Auto, EXT)

13) Multi-format Simultaneous Outputs (3G-SDI HDMI / CVBS )

14) Multi Protocol

8

5. COMPONENTS Package

Operation Manual

Operation Manual 30x Zoom Camera

Tripod Mounting HoleInstall the camera on an optional tripod.The tripod must be equipped with screws with specifications shown on the right.

Tripod MountingTripod Mounting bracket is assembledto the top and buttom of the camera.

9

6. DIMENSIONSUnit:mm

10

67

73

121.8

62.7 12

1/4” - 20NUF

7. OVERVIEWRear View

Key Buttons• Following buttons control zoom, focus, and auto focus functions. W(WIDE) button : To widen the view. (ZOOM OUT) T(TELE) button : To close in on a far object. (ZOOM IN) N(NEAR) button : To see a near object clearly. F(FAR) button : To see a far object clearly.• Pressing the M(MENU) button prompts the main setup menu.• Setup menu can be navigated using these buttons. MENU(M) button : To access the main setup menu. UP(T) button : To move the arrow indicator to up. DOWN(W) button : To move the arrow indicator to down. LEFT(N) button : To change date to down. RIGHT(F) button : To change date to up.

Control Interface• Used to connect the remote control equipment. Includes the RS-485 communication pin. Zoom and focus functions can be controlled by using external signals.

Power LED• Illuminates when power is supplied.

Video Output Jack• Used to connect an external video monitor in jack.

Power Input Terminal• Power supply terminal(DC12V± 10%)

11

Power LED

Power InputTerminal

Control Interface

Key Buttons

Video Out Jack

HDMI

HD-SDI Jack

8. INSTALLATIONConnecting to Monitor• Connect Video Out Jack to the monitor’s Video In Jack as shown below.

• Connection methods may vary depending on the video equipment. Please refer to the model specific instruction manual.

12

BNC Female Video

HDMI CABLE

BNC Female Video

13

8. INSTALLATIONConnecting to PowerConnect the power cable to the camera’s power in as shown in the figure below

Resistance of copper wire [at 20℃ (68˚F)]Copper wire size

(AWG) #24

(0.22㎟)#22

(0.33㎟)#20

(0.52㎟)#18

(0.83㎟)

Resistance(Ω/m) 0.078 0.050 0.030 0.018

Voltage Drop(V/m) 0.028 0.018 0.011 0.006

• As the voltage drop according to the length of the cable in the above table, a camera may malfunction if there is an excessively long cable run.

• Voltage drops in the above table are variable according to types of cable manufacturer.

• Connect the power once the installation is complete.• When connecting to the power source, make sure the polarity of the power adapter is correct. • Use a DC12V/500mA power source for the camera.

NOTE

DC12V Regulated Power Supply

14

8. INSTALLATIONControl Interfaces(Communication Control Connector)The camera can be controlled by using external controllers like as the keyboard controller.(RS-485 Communication)

Connecting PC or DVR (Serial Port)

Connecting to RS-485 ControllerRS-232C TO RS-485 CONVERTER

15

8. INSTALLATIONConnecting to External Controller

EXT & GND Open: DAYEXT & GND Close: NIGHT

16

9. SPECIFICATIONImage Device 1/2.9” Sony Exmor CMOS Sensor

Effective Pixels About 2.14Mega pixel

Minimum illumination 0.6 lx (F1.6, 30IRE, ICR OFF) / DSS on: 0.02 lx0.06 lx (F1.6, 30IRE, ICR ON) / DSS on: 0.002 lx

Lens x30 ( f=4.3 ~ 129.0mm), F1.6(Wide)~F5.0(Tele)

View of angle Horizontal : 65.1° (Wide end) to 2.34° (Tele end)

Digital Zoom (PIP, PTZ) OFF ~ x10 Var iable (Total x300)

AF AUTO / ONE SHOT / MANUAL

White Balance ATW / AWC / OUTDOOR / INDOOR/MANUAL

Day & Night AUTO / SENSOR / VIDEO / EXT

3DNR OFF/1~5

WDR/HLC/BLC ON/OFF (User Setting)

DEFOG OFF/LOW/MIDDLE/HIGH (User Sett ing)

AGC OFF~42dB

Digital Image Stabilization ON/OFF

Digital Slow Shutter ON/OFF (x2 ~ x30 Var iable)

Shutter Control AUTO/IRIS FIX/SHUTTER FIX/GAIN FIX/MANUAL

Privacy Zone Masking ON/OFF (8 Rectangle areas)

Communication RS-485, VISCA protocol , Pelco-D/P

Image Processing Image Fl ip / Mirror / Mot ion Detect ion(4 areas)Digi ta l Zoom PIP(Only 1080P 30fps)

Digital Video Output HDMIMAX. 3G-SDI IF 1080P@60fps

Analog Video Output960H or 760H Composi te Output 1Vp-p

(75 Ohm Terminal)

Operat ing Temperature -5°C ~ +50°C

Storage Temperature -20°C ~ +60°C

Dimension (W x H x D) 67 x 121.8 x 73mm

Power Consumption DC 12V (±10%), Max 550mA (60fps, motor act ive)

Speci f icat ions and designs are subject to change for improving the funct ional i ty of th is product wi thout not ice.

17

10. OSD MENU STRUCTUREOSD Working• Entering Main menuA. If you press ENTER button for more than 3sec then menu will appear on the monitor.B. If you press TELE button then cursor will move to UP MENU BAR, and if you press

WIDE button then cursor will move to DOWN MENU BAR.C. After you select a Main-menu, if you press ENTER button then menu-bar will move

to Sub-menu.

• Moving to Sub-menuA. If you press NEAR button, value will be decreased, and if you press FAR button,

value will be increased.B. After you select a Sub-menu, IF you press ENTER button then menu-bar will move

to Sub-menu.C. To return Main-menu, move menu-bar to RETURN and press ENTER.

MAIN MENU

LENS SETUPAE SETUPAWE SETUPSMART SETUPADVANCED SETUPGENERAL SETUPFACTORY RESETEXIT

LENS SETUP

AF MODE ONESHOT AF SENSITIVITY 5AF TIME 10 SECONE. AF TIME OFFMIN. DIST 1MZOOM SPEED FASTZOOM LIMIT OFFEXIT RETURN

10. OSD MENU STRUCTURE• Exiting from MenuA. At Main-menu, move menu-bar to EXIT MENU, and press ENTER button.B. At Sub-menu, move menu-bar to EXIT MENU, and press ENTER button.C. EXIT : The changed values will be stored.

Menu details• LENS SETUPAt Main-menu, select LENS SETUP MENU, and press ENTER button.

1. AF MODE: Set AF MODE

AF MODE: AUTO → MANUAL → ONESHOT

AUTO: Use to focalize automatically all the time.MANUAL: Use to focalize manually pushing NEAR or FAR key.

Even though MANUAL mode, it will be focalizeds in some time after zoom in or out, and then return to MANUAL mode automatically.So you can change the focus manually.

ONESHOT: It is same with MANUAL mode in function aspect. But it focalizes whenever you push ONESHOT key.This function is similar to manual mode, but only when the key(Menu/Tele/Wide) is pressed, It will be focusing.ONESHOT act automatically, It will be returned to MANUAL mode in 5 seconds.

2. AF SENSITIVITY: You can adjust sensitivity of AUTO FOCUS.

SENSITIVITY: 1 → 2 → ...→ 10

18

LENS SETUP

AF MODE ONESHOT AF SENSITIVITY 5AF TIME 10 SECONE. AF TIME OFFMIN. DIST 1MZOOM SPEED FASTZOOM LIMIT OFFEXIT RETURN

10. OSD MENU STRUCTURE3. AF TIMESet AF time. When AF is completed, Focus mode will be Manual.Even when AF is not completed, it stops when time is up.(unit : sec)

AF TIME: 5 → 6 → ...→ 15

4. ONE. AF TIMESet the ONE.AF TIME. When the user sets the ONE.AF TIME, the ability to automatically adjust the AF once in that time. (unit :Hour)

ONE. AF TIME: OFF →1 → 2 → ...→ 24

5. MIN.DISTSet the minimum distance which can be focalized.MIN.DIST: 10cm → 30cm → 1m → 1.15m → 1.3m → 1.5m → 2m → 3m → 6m → 10m

6. ZOOM SPEEDSet zoom speed slow to fast , 3 steps

ZOOM SPEED: SLOW → MEDIUM → FAST

7. ZOOM LIMITSet ZOOM LIMIT.

ZOOM LIMIT: OFF → ON

START ZOOM: Set boundary value of WIDE zooming.D-ZOOM OFF : START ZOOM X1 ~ X29D-ZOOM ON : START ZOOM X1 ~ X30

END ZOOM: Set boundary value of TELE zooming.D-ZOOM OFF: END ZOOM X2 ~ X30D-ZOOM ON : END ZOOM X2 ~ X300It sets as the unit of x10 in electronic zoom region.Since Start Zoom and End Zoom ratio are set, simultaneously Camera moves to setting magnification. So it enables to adjust in moving to desired position.

EXIT: After you select a RETURN, IF you press ENTER button then menu-bar will move to main-menu.After you select a EXIT, IF you press ENTER button then Updated data will be saved and exit menu.

19

ZOOM LIMIT SETUP

START ZOOM X1END ZOOM X30EXIT RETURN

20

10. OSD MENU STRUCTURE• AE SETUPAt Main-menu, select AE SETUP MENU, and press ENTER button.

1. AE MODESet AE MODE.AE MODE function works as following order.

AE MODE: AUTO → IRIS FIX → GAIN FIX → SHUT FIX → MANUAL

AUTO: Exposure is controlled by Shutter Speed, Iris, Gain to meet the Brightness.You can adjust MAX AGC, MAX DSS, BRIGHTNESS, ZOOM PROP .IRISMAX AGC: OFF → 2DB → 4DB → … → 42DB MAX DSS: OFF → X2 → X4 → … → X30BRIGHTNESS: 1 → 2 → … → 100ZOOM PROP .IRIS: ON → OFF

IRIS FIX: Iris is fixed, Exposure is controlled automatically by Shutter Speed and Gain. You can adjust IRIS , MAX AGC , MAX DSS , BRIGHTNESS.IRIS: F1.6 → F2 → F2.3 → … → F22MAX AGC: OFF→ 2DB → 4DB → … → 42DB MAX DSS: OFF→ X2 → X4 → … → X30BRIGHTNESS: 1 → 2→ … → 100

GAIN FIX: Gain is fixed, Exposure is controlled by Shutter Speed, and Iris is full open.You can adjust GAIN , MAX DSS , BRIGHTNESS.GAIN: OFF → 2DB → 4DB → … → 42DBMAX DSS: OFF → X2 → X4 → … → X30BRIGHTNESS: 1 → 2 → … → 100

AE SETUP

AE MODE AUTO BACKLIGHT OFFDAY / NIGHT DAYDNR OFFEXIT RETURN

EXPOSURE SETUP

MODE AUTOSHUTTER OFFIRISGAINMAX AGC 24DBMAX DSS X10BRIGHTNESS 25ZOOM PROP .IRIS ONEXIT RETURN

10. OSD MENU STRUCTURESHUT FIX: Low / High shutter speed is fixed, Exposure is controlled automatically by Iris and Gain.

You can adjust SHUTTER , MAX AGC , BRIGHTNESS . ZOOM PROP.IRIS.SHUTTER: AUTO → 1/60 → FLICKER → … → X30MAX AGC: OFF → 2DB → 4DB → … → 42DBBRIGHTNESS: 1 → 2 → … → 100ZOOM PROP .IRIS: ON → OFF

MANUAL: Shutter Speed, Iris, Gain is fixed as set value regardless of illuminance.You can adjust SHUTTER , IRIS , GAIN , BRIGHTNESS.SHUTTER: AUTO → 1/60 → FLICKER → … → X30IRIS: F1.6 → F2 → F2.3 → … → F22GAIN: OFF → 2DB → 4DB → … → 42DBBRIGHTNESS: 1 → 2 → … → 100

2. BACKLIGHT MODESet BACKLIGHT MODEBACKLIGHT function works as following order.

MODE: OFF →WDR→ BLC → HLC → D-WDR

WDR: WDR lightens dark spots and dims bright areas to bring a whole image into balance.GAIN: LOW → MIDDLE → HIGHWDR LEVEL: 0 → 1 → 2 → … → 10

BLC: BLC is for preventing the center object getting too dark when the excessive light is behind the central object.A. GAINLEVEL function works as following order.GAIN: LOW → MIDDLE → HIGH

B. AREA EDITIf you select AREA EDIT MENU, and press ENTER button.You can configure the area of BLC.

21

BACKLIGHT SETUP

MODE BLCGAIN MIDDLEAREA EDITAREA DISPLAYHSBLC SELECTWDR LEVEL 5EXIT RETURN

10. OSD MENU STRUCTURE

You can move BLC area by TELE,WIDE,NEAR,FAR buttons.If you press ENTER button, BLC AREA will move to NEXT SET.

You can Change BLC area size by TELE,WIDE,NEAR,FAR buttons.If you press ENTER button, EXIT SET.

HLC: HLC is ability to reverse bright points in the picture to black.HLC improves the ability of the entire system to display shades of grey elsewhere in the picture.

HLC OFF HLC ONA. GAINYou can adjust LEVEL of HLC.GAIN: 0 → 1 → … → 100

B. AREA EDITIf you select AREA EDIT MENU, and press ENTER button.

22

10. OSD MENU STRUCTUREYou can change the 4 area of HLC.

You can move HLC AREA by TELE,WIDE,NEAR,FAR buttons.If you press ENTER button, HLC AREA will move to NEXT SET.

You can Change HLC AREA size by TELE,WIDE,NEAR,FAR buttons.If you press ENTER button, EXIT SET.

C. AREA DISPLAYSet AREA DISPLAYAREA DISPLAY: OFF → ON

D. HSBLC SELECTSet HSBLC SELECTHSBLC SELECT: DAY → NIGHT

D-WDR: Digital Wide Dynamic Range (D-WDR) is a function in some intended to provide clear images even under varying intensity of illumination, using software.

Real WDR lightens dark spots and dims bright areas to bring a whole image into balance.

23

10. OSD MENU STRUCTURE3. DAY/NIGHT MODESet DAY/NIGHT MODEDAY/NIGHT function works as following order.

DAY / NIGHT: AUTO → DAY → NIGHT → EXT

MODE: DAY mode becomes Color mode, and NIGHT mode becomes black&white mode. AUTO mode is converted Day&Night automatically according to illuminance change.EXT mode is converted Day&Night according to User Signal.MODE: AUTO → DAY → NIGHT → EXT

DWELL TIME: You can adjust DWELL TIME in the Auto Mode.DWELL TIME: 2 → …. → 60

DETECT MODE: VIDEO only (depends on circumstantial brightness)

D→N LEVEL: You can adjust gain (When converting from day to night…)D→N LEVEL: 2 → …. → 36 DB

N→D LEVEL: You can adjust gain (When converting from night to day…)N→D LEVEL: OFF → …. → 33 DB

SMART IR LEVEL: Set the SMART IRSMART IR: OFF → …. → 15

SMART IR EDIT: SMART IR Position Set

4. DNR MODEImage noise can be reduced by using the DNR function.The intensity of the Noise Reduction filter can be selected 2D-DNR or 3D-DNR.

DNR MODE: OFF → 2D-DNR → 3D-DNR → AUTO

24

DAY / NIGHT

MODE AUTODWELL TIME 5DETECT VIDEOD -> N LEVEL 2 DBN -> D LEVEL OFFCOLORSMART IR LEVELSMART IR EDITEXIT RETURN

25

10. OSD MENU STRUCTURE• AWB SETUPAt Main-menu, select AWB SETUP MENU, and press FAR button.

1. ATW MODEColor temperature is directly related to environment and it influences on the color of image.ATW automatically adjusts the white balance in response to varying light conditions.ATW has color temperature range of 2,500°K ~ 8,000°K.

2. ATW MODEConsider current illumination condition, force to conduct white balance and lock as manual.

3. INDOORFixed as 3200°K.

4. OUTDOORFixed as 5400°K.

5. MANUAL MODEUser can adjust RED and BLUE gain manually (0~100).

RED gain : At Manual mode, you can adjust RED gain.GAIN: 0 → 1 → … → 100

BLUE gain : At Manual mode, you can adjust BLUE gain.GAIN: 0 → 1 → … → 100

WHITE BALRANCE

MODE ATWRED GAINBLUE GAINEXIT RETURN

26

10. OSD MENU STRUCTURE• SMART SETUPAt Main-menu, select SMART SETUP MENU, and press ENTER button.

1. PRIVACY MASKPZM(Privacy Zone Mask) is to hide the unwanted view to protect privacy invasion.It works with Zoom/Pan/Tilt operation.

PRIVACY MASK: OFF → ON

NUMBER: You can configure up to 8 PZM (Privacy Zone Mask) areas.NUMBER: 1 → … → 8

LOCATION: If you press ENTER button at LOCATION, below screen will appear.

You can move PRIVACY MASK area by TELE,WIDE,NEAR,FAR buttons.You can decide the LEFT and UP size of PRIVACY MASK.If you press ENTER button, will move to NEXT SET.

You can decide the RIGHT and DOWN size of PRIVACY MASK.If you press ENTER button, EXIT SET.

SMART SETUP

PRIVACY MASK ON MOTION DETECT ON EXIT RETURN

PRIVACY SETUP

NUMBER 1LOCATIONDISPLAY OFFCOLORTRANSPARENCYEXIT RETURN

27

10. OSD MENU STRUCTUREDISPLAY: PRIVACY MASK area can be displayed or not-displayed during

PRIVACY MASK setting.

PRIVACY MASK area can be color display or mosaic display during setting.DISPLAY: OFF → MOSAIC → COLOR

COLOR: You can select color of PRIVACY MASK.COLOR: GRAY → YELLOW → … → BLACK

TRANSPARENCY: Transparency of PRIVACY MASK area can be decided.TRANSPARENCY: 0 → 25 → 50

2. MOTION DETECTIONMotion can be detected and displayed in appointed area.It is possible to set up motion detection zones user wish.SET MOTION DETECTION.

MOTION DETECTION: OFF → ON

DISPLAY MODE: Display mode can be selected as Off, OSD, MOSAIC, MOSAIC + OSD.

DISPLAY MODE: DISPLAY MODE: OFF → OSD → MOSAIC → MOSAIC+OSD.

NUMBER: You can configure up to 4 Motion detection areas. NUMBER: 1 → 2 → 3 → 4

USE: You can decide whether will use motion detection function or not. USE: OFF → ON

EDIT: If you select EDIT MENU, and press ENTER button.You can configure the area of MOTION DETECTION.

MOTION DETECTION

DISPLAY MOSAICNUMBER 1USE OFFEDITCOLOR WHITESENSITIVITY 5DWELL TIME 5 SECEXIT RETURN

28

10. OSD MENU STRUCTUREYou can move PZM area by TELE,WIDE,NEAR,FAR buttons.If you press ENTER button, MOTION DETECTION AREA will move to NEXT SET.

You can Change PZM area size by TELE,WIDE,NEAR,FAR buttons.If you press ENTER button, EXIT SET.

COLOR: You can select color of MOTION DETECTION.COLOR: NONE → RED → WHITE → BULE

SENSITIVITY: You can decide sensitivity of MOTION DETECTION area.SENSITIVITY: 0 → 1 → … → 60

DWELL TIME: You can decide dwell time.(unit : sec).DWELL TIME: 0 → 1 → … → 15

• ADVANCED SETUPAt Main-menu, select ADVANCED SETUP MENU, and press FAR button.

1. DISDigital Image Stabilizer compares current and previous images in order to identify a global motion and adjust the motion using the difference between the two images if there is an overall dancing in the image.

DIS removes image jitter causing by vibration or wind.You can decide whether will use DIS function.DIS: OFF → ON

ADVANCED SETUP

DIS OFFD-ZOOM OFFDEFOG OFFLENS SHADE ONMIRROR NORMALNEGATIVE OFFFREEZE OFFEXIT RETURN

29

10. OSD MENU STRUCTURE2. Digital ZOOMD-ZOOM is accomplished electronically, with no adjustment of the camera’s optics, and no optical resolution is gained in the process.You can decide whether will use D-ZOOM function. D-ZOOM: OFF → ON

PIP MODE: PIP(Picture – in – Picture) is an additional camera display clip that into the main camera display.

A. PIP MODEYou can decide whether will use PIP function.PIP MODE: OFF → ON

B. EDITIf you select EDIT MENU, and press ENTER button.You can configure the area of PIP.

You can move PIP area by TELE,WIDE,NEAR,FAR buttons.If you press ENTER button, EXIT SET.

3. DEFOGIf the fog occurs, the dynamic range is reduced and will fall the image. If you DEFOG ON the image is your favorite.

DEFOG: OFF → ON

FOG DEFOG

PIP

PIP MODE ON EDITEXIT RETURN

30

10. OSD MENU STRUCTURE EDIT: If you select EDIT MENU, and press ENTER button.

You can configure the area of DEFOG.

You can move DEFOG area by TELE,WIDE,NEAR,FAR buttons.If you press ENTER button, DEFOG AREA will move to NEXT SET.

You can Change DEFOG area size by TELE,WIDE,NEAR,FAR buttons.If you press ENTER button, EXIT SET.

GRANDATION: You can adjust strength of gradation.GRANDATION: LOW → MIDDLE → HIGH

4. LENS SHADEMode ON compensates for the signal degradation by digitally gaining pixels on the image periphery.LENS SHADE OFF is function Stop.

LENS SHADE: OFF → ON

5. MIRRORMirror function works as following order.

MIRROR: NORMAL → H-FLIP → V-FLIP → ROTATE

6. NEGATIVEMode ON is Negative mode, Mode OFF is Positive mode namely general screen state.

NEGATIVE: OFF → ON

7. FREEZEIt pause current image. ON is to stop, OFF is to return to normal state.

FREEZE: OFF → ON

31

10. OSD MENU STRUCTURE• ADJUST SETUPAt Main-menu, select ADJUST SETUP MENU, and press ENTER button.

1. DEFECTDefect function works as following order.Defect ON case be able to set the defect level. DEFECT: OFF → ON → AUTO

2. SHARPNESSSharpness is controllable SHARPNESS: 0 → 1 → …. → 15

• GENERAL SETUPAt Main-menu, select GENERAL SETUP MENU, and press ENTER button.

1. INFORMATIONIt displays current information(MODEL, ID, BAUDRATE, PROTOCOL, VERSION, FRAME RATE) state of Camera.

2. MENU OFF TIMEIf you are not using the Menu key, the user settings “menu” disappears automatically at the time specified. MENU OFF TIME: OFF → 5 SEC → …. → 60 SEC

ADJUST SETUP

DEFECT ONSHARPNESS 8EXIT RETURN

ADJUST SETUP

INFORMATIONMENU OFF TIMEOSD DISPLAYCOMMUNICATIONLANGUAGEFRAMERATEEXIT RETURN

32

10. OSD MENU STRUCTURE3. OSD DISPLAYIt displays current operating state of Camera. MENU OFF TIME: OFF → 5 SEC → …. → 60 SEC

Display Default Position

ID(PLACE): CAMERA ID can be shown on monitor. In the state of being turned ON ID, by pressing the ENTER button, the user can select the position of the ID.ID: OFF → ON

ZOOM(PLACE): State of CAMERA ZOOM can be shown on monitor. In the state of being turned ON ZOOM, by pressing the ENTER button, the user can select the position of the ZOOM.ZOOM: OFF → ON

TITLE(PLACE): CAMERA TITLE can be shown on monitor. In the state of being turned ON TITLE, by pressing the ENTER button, the user can select the position of the TITLE.TITLE: OFF → ON

TITLE EDIT: IT is the name of Camera. It enters 15 characters including space. TITLE : ■■■■■■■■■■■■■■■

For example, if you want to display “A” on the monitor.Select “A” using TELE(up), WIDE(down), NEAR(left), FAR(right) buttons.Move to cursor selected “ A ” position. AB C D E F G H I J K L M NO P Q R S T U V W X Y Z 1 23 4 5 6 7 8 9 0 & + - ( )B A C K S P A C E <┛C L E A R <┛ E X I T

Push ENTER button to enter the character “A”TITLE : A_

33

10. OSD MENU STRUCTURE4. COMMUNICATIONAt Main-menu, select COMMUNICATION MENU, and press ENTER button.

ID: ID can be configured between 1~255. If you want to change the ID, press the ENTER button.

PROTOCOL: Set PROTOCOL. If you want to change the PROTOCOL, press the ENTER button.PROTOCOL AUTO → PELCO_D → PELCO_P → VISCA

BAUD RATE: Set BAUD RATE. If you want to change the BAUD RATE, press the ENTER button.Use to communicate through RS232C, RS485, RS232TTL.BAUD RATE 2400 → 9600 → 19200 → 38400 → 57600 → 115200

5. LANGUAGEOSD language support English only. LANGUAGE ENGLISH

6. FRAMERATEFRAME RATE (also known as frame frequency) is the frequency (rate) at which an imaging device produces unique consecutive images called frames.NTSC is, supports 30/60 frames per second, PAL is supports 25/50 frames.add frame rate 1080i59.94 , 1080p50/24. (not change NTSC ↔ PAL ) * DIS and PIP, WDR and D-Zoom is initialize by frame rate change, And Analog output 1080i60 does not support OSD

FRAMERATE: If you select PAL or NTSC of CVBS, frame rate can be change to the case of two.Move the cursor to the desired FRAMERATE(CVBS) and press “ENTER” button. And then you can see the question whether want to change, Left is a change and reboot , the right is canceled. After the question , if you are not any action.The Osd menu go back to previous state automatically.CASE1 NTSCFRAMERATE 1080P60/60 → 1080P60/30 → 1080P30/30 → 720P60/60 → 1080I 60/60 → 1080I 59.94CASE2 PALFRAMERATE 1080P50/50 → 1080P50/25 → 1080P25/25 → 720P50/50 → 1080I 50/50 → 1080p 50/24

COMMUNICATION

ID 1 PROTOCOL AUTO BAUD RATE 2400 EXIT RETURN

34

10. OSD MENU STRUCTURE CVBS: Set CVBS output. NTSC and PAL , 2 steps

CVBS: NTSC → PAL

7. FACTORY RESETAt Main-menu, select FACTORY RESET MENU, and press ENTER button.Move menu-bar to “CLEAR” and press ENTER button, all data will be returned factory default values. FACTORY RESET: NO CLEAR → CLEAR