m518 gps intelligent terminal user manual

Gator www.gatorcn.com China

b

M518 GPS Intelligent Terminal

GPS+GPRS+GSM User Manual

Edition 1.2

Copyright Feb. 15, 2009

GATOR GROUP CO.,LTD. All rights reserved.

LA Brand

http://www.gatorcn.com

China Printing

ADD: 312# Ansheng Building,Xixiang section of 107 National road ,Bao'an, Shenzhen, China

TEL: 86-75529566336

FAX: 86-75529566339

WEB: http://www.gatorcn.com

EMAIL: [email protected]


Notes:

Please mount the device steadily on the flat place before using;

Please make sure the voltage value is right before connecting with battery, and placing the wires to where shouldnt be trodden;

Please power off when plugging or taking out of any module or connector;

Please keep the device dry and dont let any liquid fall into the device in case any damage caused in the device or circuit;

If any problem caused as follows, please turn to professional technician:

When power wire, keyboard, or socket are damaged;

When liquid infiltrating into the device;

When the device work unusually or cannot resume to normal even operated according to the instruction;

When the device cannot as usual after falling, throwing or breaking;

When there is obvious damage in the device.


Content 1. Product Introduction 4

2. Characteristics 4

3. Specifications 5 3.1. Hardware datasheet 5 3.2. Others 6

4. Connector Discription 7 4.1. Power Connector 7 4.2. External Serial Port/ Vehicle Handle 8 4.3. Expanding Interface 1 9 4.4. Expanding Interface 2 10 4.5. Expanding Interface 3(Serial camera) 11 4.6. Expanding Interface 4 (LED AD Screen) 11

5. Installation 12 5.1.Warm reminder for Installation 12 5.2. Wiring diagram 12 5.3. Parameter settings 14

6. Standard Accessories 16

7. Optional Accessories 16 7.1. Oil collector 16 7.2. Tapping Line 16 7.3. Relay for oil or circuit immobilization 17 7.4. Serial Camera 17 7.5. Image Acquisition 17 7.6.Vehicle Handle 17 7.7. Scheduling Screen 18 7.8. TFT Screen Navigator 18 7.9. LED AD Screen 18


1. Product Introduction M518 GPRS/GSM Model GPS intelligent terminal (Mobile user terminals)

Built-in industrial GPRS/GSM communication module and the newest SIRF-Star III High-sensitivity GPS receiver positioning moduleadopt GPRS and SMS Dual-mode communication, terminal run stably and reliably, full functions, multi-interface, the terminal can be applied to concrete, rental, logistics, public transport, bus and other fields, and also according to different industries, tailored to different users.

2. Characteristics 1) easy to install; 2) accurate GPS positioning, dynamic positioning deviation is less than 5 m; 3) support GSM voice and SMS functions, UDP / TCP protocol communications in

GPRS mode; 4) support the GPS data uploading at intervals and location; 5) support the two way voice communication function; 6) support Call Barring of group numbers function; 7) support two way SMS communication via Mobile and PC software; 8) support the mute function; 9) support authorized tapping function; 10) support protection from high or low level voltage function; 11) support 5 levels of signal detection; 12) support the data resend from signal dead zone function; 13) support remotely locking vehicle function; 14) support watching vehicle function; 15) support SOS alarm function; 16) support the power-off alarm function; 17) support the high-voltage under-voltage alarm and alarm functions; 18) support over speed alarm function; 19) support parking alarm function;


20) support illegal door-open, illegal engine-start alarm function; 21) support fuel consumption detection; 22) support fuel changing alarm; 23) support mileage statistics; 24) support Geo-fence alarm; 25) support fatigue driving alarm; 26) support temperature detection alarm; 27) support three serial peripherals (such as the car handles, scheduling screen, camera);

3. Specifications

3.1Hardware parameter

working voltage 8VDC36VDC

Working current 50mA~160mA

GSM module inside contain frequency GSM 900/1800 inside contain frequency GSM 850/900/1800/1900Mhz (can tailor)

Communication protocol

UDP/TCP(can customize)

GPS module GPS SIRF-Star III CMOS chip group

GPS sensitivity -159dBm

GPS frequency L1, 1575.42 MHz

C/A coding 1.023 MHz chip rate

Channels 20 channels for tracking

Position accuracy 10 meter, 2D RMS

Speed accuracy 0.1 meter/second

Time accuracy GPS synchronization

Default data WGS-84


Recover Average 0.1 second

Hot start Average 1 second

Warm start Average 38 second

Cold start Average 42 second

Height limit 18,000 meter (60,000 feet) max

Speed limit 515 kilometer/second (1000 knots)max

Acceleration limit Less than 4g

Expansion peripheral

Peripherals can be accessed by an extension (such as: Handle / scheduling screen / camera etc.)

3.2Others

Work temperature -20 70 C

Storage temperature -30 85 C

Humidity 5% 95% non-condensing

Terminal size 130 mm 95mm 32mm

Inside battery Continuing working not less than 4 hours

LED light Red: MCU status; Green: GSM module status


4. Connector Description

4.1 Power interface

Description

pin color function explanation/connection method

1 red Power positive input, the working voltage 9VDC ~ 34VDC, connect the positive of car battery;

2 dark Power negative input, then the negative terminal of vehicle battery; 3 yellow ACC check lineconnect car key ACC line access;


4.2 Expanding Interface 1

Description


1 red SOS alarm input, low-level triggered alarm, directly connect with the wire of SOS button 2 black Relay negative input, connect with the white wire in relay

3 yellow Relay positive input, connect with the yellow wire in relay

4 blue HV2( high-level signal detection port 2,) input positive voltage to detect, which should be 5DC~input power supply, connecting with effective high-level signal wire.

5 purple GND of SOS alarm wire

6 brown SOS alarm indicator signal, drive LED, when alarm is triggered, the LED will be on. 7 orange Door open/close signal detection.

8 white

HV1( high-level signal detection port 1, it is described as A/C on/off signal detection), input positive voltage to detect, which should be 5DC~input power supply, connecting with effective high-level signal wire.

9 red 5VDC power (max output current: 220mA)

10 green Positive pole for oil collecting signal, connecting with the added sensor of fuel volume or original sensor of vehicle

11 grey Oil collecting control signal wire (when connecting with oil collector), please note: this wire are unable to connect with ground.

12 black AD signal detection, detect the temperature.


4.3 Expanding interface 2

Handset

Description


1 red Power positive output, 5VDC

2 yellow RXD, serial input, RS-232 level, the baud rate 19200bps;

3 green TXD, serial output, RS-232 level, the baud rate 19200bps;

4 orange Detectaphone positive input, MIC (with Orange line lead with the monitor DC) 5 white Detectaphone negative input, MIC

6 blue Headphone positive output, SP

7 brown Headphone negative output, SP

8 black Power negative output


Serial camera

Description


1 red +5VDC power

2 black GND

3 yellow RXD , terminal serial port for data-reading, the baud rate 9600bps;

4 green TXD , terminal serial port for data-typing, the baud rate 9600bps;

LED AD Screen

Description

wire color function explanation/connection method

1 green TXD , terminal serial port for data-typing, the baud rate 9600bps;

2 yellow RXD , terminal serial port for data-reading, the baud rate 9600bps; 3 black GND


5. Installation

5.1 Warm reminder for Installation

In order to realize the full functions of this product, please read this manual carefully before starting to use the product. 1. This product can only be maintained and repaired by qualified professional service personnel. If you detach this product for maintenance or repair, your warranty will be invalidated. 2. When connecting the other devices, read carefully their instruction manuals, so as to carry out correct installation; do not connect incompatible device. 3. Please use genuine original parts and qualified batteries and peripheral equipments, so as to avoid damage to this product. 4. As this product is a high-tech product, please read carefully this manual before starting to use the product, so as to avoid inappropriate operation. 5. Drivers should not operate this product while driving a vehicle, thereby, affecting safe driving. 6. This product can work properly only when GSM communication is in good condition. 7. Please reduce electromagnetic wave interference to the product; and use it properly. 8. GPS communication is liable to be affected by environmental shielding; may fail to carry out positioning during certain circumstances. It will resume the positioning function as soon as it leaves the shielding environment. This is normal. Please do not worry when encountering such problem. 9. Each signal sent out from the system will be confirmed for successful transmission in the base station of the mobile operator. However, if system stoppage occurs or if the mobile telephone is preset to a switch off state by the customer, it cannot ensure successful transmission. 10. For safety reason, do not tell the other people your device SIM number, without taking precautions. Otherwise, your privacy may be compromised along with other safety problem.

5.2 Parameter settings

5.2.1 via the handle. Please set from the handle


Default code:20050215

Phonebook

SMS

Edit new SMS

calls

Settings

Menu 1.Search contact 2.add new contact

3.group phone number 1.fixed SMS

2.Saved SMS

3.Received central SMS

4.Received phone SMS

1. Dialed calls

2 . Received calls

3.Missed calls

1.default setting

2.contrast

3.host status checking

4.terminal self-checking

5. car-watching setting

6rings

1.IP setting

2.own number

3.service SMS number

4.phone function

5.security setting

6.APN setting

7.module initialization

1. connect with handle or scheduling screen, then do as follows

i. press menu, enter into settings, choose default setting, the password:

20050215, hint success to get the next step.

ii. Set ip address and port, the format as follows: 0,xxx.xxx.xxx.xxx,

8886 ( input, press * , input. Press #), which means Y+IP+PORT, If IP dont have three digits, please add 0in front of it to up 3 digits, Y means: 0- private net, 1- public net, in practice, please ignore it. hint success to get the next step. such as our platform servers IP and PORT as follows: 0,058.060.185.172, 8886

iii. Set own number, please make sure the own number should be 11 digits. such as :12345678901, hint success to get the next step.

iv. Set APN. You can input the APN manually. If ok . all parameters are set.


If all done , generally in 60 seconds, the screen shows means detected GPS signalGP stand for that the terminal detected GPRS signal, in the meantime, monitoring centre can correctly track vehicle , means terminal work normal. Notes: Input parameters must be correct, it is recommended that use the handle of the "host status query" function to check the parameters after the set up.

5.2.2 Via SMS command. 1.Reboot

R,* Password *

2. settings command: SS,*APN*,*USERNAME*,*PASSWORD*,*IP*,*port*,*terminal ID*,*+Service

SMS number* ,*Password* Notes: a.If no username and password,please fill it with this:

SS, *APN*,**,**,*IP*,*port*,*terminal ID*,*+Service SMS number* ,*Password* b.terminal ID length must be 11 digitals, and set different terminal ID at the latter 9 digitals c.please add country code in the front of service SMS number, such as:Chinese code is 86. SMS number is 13612345678, You can set the SMS number like this, *+8613612345678* d.default password is 123456 3.change password C,*password*,*new password*

5.2.3 Via simulative handle(PC software).

Please visit our website to download simulative handle program.the link as follows:

http://www.gatorcn.com/

5.3 how to track by software 1. Add device into tracking system.

1.1 open adding vehicle system(recommend that open this link via IE) http://211.154.139.208:8000/vms/ please get login ID from sales who follows 1.2. create a fleet for vehicle, Steps as follows: Click new fleet , input Fleet name, then save. 1.3 Create new vehicle, steps as follows


a. Click new vehicle b. Fill the blanks with *, the most important item is system Number, it should be unique ID,

set ID begin with 13 and ID should be 11 digits, for example: 13512345678

1.4 open tracking software: http://gps.gatorcn.com/ ( same login ID with VMS) 2. Insert SIM card , connect with antenna and power supply

2.1 open the device as picture shows:

2.2 insert SIM card into tracker, details please see picture:

2.3 connect GPS and GSM antenna with tracker, please operate carefully, and put antennas in

the open air. 2.4 Connect with power supply.

3.Parameter settings to connect with server via SMS.

Edit following SMS command in cell phone and send it to the SIMCARD inside tracker, please edit exact format as following SMS. 3.1 APN with username and password

SS,*APN*,*USERNAME*,*PASSWORD*,*IP*,*port*,*terminal ID*,*+Service SMS number* ,*Password* 3.2 APN without username and password:

S, *APN*,*IP*,*port*,*terminal ID*,*+Service SMS number* ,*Password*

Get reply after you send this SMS command within 2 minutes. Notes: a. APN: Access Point Name of GPRS, you can get APN of SIM card from local operator b.terminal ID is same as system number created under VMS( 11 digits and begin with 13). c.please add country code in the front of service SMS number, such as:Chinese code is 86. SMS number is 13612345678, You can set the SMS number like this, *+8613612345678* d. service SMS number: it is for receiving SMS alarm to monitor vehicle, for example, if press SOS button, service SMS number will get SOS alarm.


d.default password is 123456 for example, our servers IP: 211.154.139.208 and port:8888 , set parameters as follows to host device in our server: S,*APN*,* 211.154.139.208*,*8888*,*13688998881*,*+8613418776340*,*123456* 4. track device in real time open tracking software: http://gps.gatorcn.com/ ( same login ID with VMS), and then you can track your vehicle in real time, more detailed operation, please download Demo vedio for VMS and web mornitoring system from our official website: http://www.gatorcn.com/DownLoad.aspx

6. Standard Accessories

Power Line, 9PIN Expanding Line 1, 9PIN Expanding Line 2, SOS Alarm Line, GPS Antenna, GPRS Antenna, Velcro, Warranty Card, Return Receipt of Warranty Card, Qualification.

7. Optional accessories

7.1 Oil collector


7.2 Tapping Line

7.3 Relay for oil or circuit immobilization

7.4 Serial Camera

7.5 Image Acquisition


7.6 Vehicle Handle

7.7 Scheduling Screen

7.8 TFT Screen Navigator

7.9 LED AD Screen

m518 gps intelligent terminal user manual

Documents