GENERAL REPAIR Complete Your Shop With Coats® Equipment

Double Wall Runways with "Z" Rails, Built-in Radius Plate

Pockets & Rear Slip Plate

4 POST ALIGNMENT OR SERVICE

15,000 LB. / 6.8T CAPACITY

4 POS

T ALIG

NMEN

T OR

SERV

ICE 15

,000 L

B. / 6

.8T CA

PACIT

Y

CONTACT US NOWwww.coatsgarage.com or call 1-855-876-3864

To learn more about the 15K 4 Post, or any of our other quality products, contact your authorized Coats distributor or call 1-855-876-3864 for the dealer nearest you.

Open Runway Slots Under Rear Slip Plates

#4T415CSAR1

Machined Pulleys and Cables

9" / 229 mm Machined Pulleys with 9/16" / 14mm Cables

Double Wall Deck with Z Rail

24" / 610 mm

SPECIFICATIONSCapacity 15,000 lbs / 6.8T

Overall Length Extended Model 285 1/8" / 7242 mm

Overall Length Standard Model 257 7/8" / 6550 mm

Deck Length Extended Model 237" / 6020mm

Deck Length Standard Model 210" / 5334mm

Overall Width 137 1/2" / 3493mm

Deck Width 23" / 584mm

Lowered Height 7 3/4" / 197mm

Raised Height 74" / 1880mm

Min. 4 Wheel Align. WB 88 1/2" / 2248mm

Max.4 Wheel Align. WB 164 1/2" / 4178mm

Max. 2 Wheel Align. WB 220 1/2" or 193 1/2" /

5601mm or 4915mm

Max. Service WB 232" or 205" / 5892mm or 5207mm

Lift Time 70 seconds

Power Requirement 230V - 60Hz - 1 Ph - 20amp

Footprint 137 1/2"w x 285 1/8"d x 86"h

Ceiling Height Required 12'

Shipping Weight 5,000 lb. / 2.3T

Part Number Alignment: 4T415CSAR1Extended: 4T415CXAR1Service: 4T415CSSR1Extended: 4T415CXSR1

4 POST ALIGNMENT OR SERVICE 15,000 LB. / 6.8T CAPACITYLEGENDARY RELIABILITY WITH STATE OF THE ART CAPABILITY.

Part No. MKT00191 Spec 08/17 Rev.01© 2017 Hennessy Industries, Inc.

1601 J.P. Hennessy Drive, LaVergne, TN 37086 (800) 688-6496 or (615) 641-7533Hennessy Canada: 2430 Lucknow Drive, Unit 9, Mississauga, Ontario L5S 1V3 (905) 672-9440

www.coatsgarage.com

EQUIPMENT FOOTPRINT

FEATURES

RECOMMENDED OPTIONAL ACCESSORIES

• Built to higher quality standard; 100% North American made premium US Bucher 2HP / 1.5kw power unit.

• Corrosion resistant protection steel components are wheel-a-brator shot blasted and acid washed before a "double bake" powder coat finish is applied.

• Superior structural strength provides longer life and more precise alignments Non flex double wall 23" / 584mm wide runways with built in "Z" rail. Heavy duty 10" x 8 3/8" x 1/4" wall / 254mm x 213mm x 6mm wall columns and 3" x 8 1/4" / 72mm x 210mm tube traverse beams.

• Greater flexibility with more models to chose from Available in two runway lengths with built in wheel alignment or service deck. Lift can be ordered in red or blue.

• Premium options and accessories can expand the capabilities and service life Stainless steel radius plates and rear steer plates, built in tire inflation hoses, removable work steps, LED runway lighting and premium long life 5 year warranty HD jacking beams

• Lower maintenance costs Zirk style grease fittings at all 1

1/2" / 38mm plated hinge pins. Runway under rear slip plates is open to prevent water and dirt collecting. Thirty 7/8" / 875mm enclosed plated steel slip plate balls provide better support with minimal maintenance .

• Extended Life "Non Twist" Cable design Machined steel nickel plated 9" / 229mm pulleys with bronze self lubricating bushings. Non spin fatigue resistant 9/16" / 14mm cables are routed on double stacked pulleys (versus four stacked) to reduce stress and wear.

• Low pressure hydraulics provides longer life 4" ID x 65" / 102mm ID x 1651mm cylinder is mounted under the runway and use a premium "Parker" seal and wear ring with chrome plated plunger shaft.

• Designed for optimum productivity Single point control with stainless steel cylinder air releases engage 12 locking positions. Adjustable locking ladders 81" x 2 3/4" x 3/8" 2057mm x 70mm x 9.5mm thick allow for accurate levelling. Power unit can be mounted on a front or rear column. Built in runway compressed air outlets front and rear.

7-3/

4'' L

OW

ERED

74''

RA

ISED

86"

REV: A-01 AS TESTEDNOTE: ALL CHANGES THAT ARE MADE TO THIS PRODUCT WILL CHANGE THE REVISION REVISION TABLE SHALL RELECT THE CHANGES FOR INPECTOR

MOTOR: 2HP, 230V 1PH 60HZAMP DRAW: 14.5A@FULL CAPACITYAIR: 100~120 PSIOPERATING PRESSURE@FULL LOAD: 2750 PSIRAISE TIME: 76 SECONDSLOWER TIME: 37 SECONDS

137

1/2

"

134

"

119

"

87"

41"

2

3"

23"

285 1/8" OR [257 7/8''] OVERALL LENGTH

237" OR [210''] DECK LENGTH(MAX. SERVICE W/B 232'' OR [205'']) 44 1/8" RAMP

88 1/2" MIN. 4-WHEEL ALIGN. W/B

164 1/2" MAX. 4-WHEEL ALIGN. W/B

76" SLIP PLATE

245" OR [218'']

22"

220 1/2" OR [193 1/2''] MAX. 2-WHEEL ALIGN. W/B

40 1/8"

16 5/8" 56" OR [29'']

D

C

B

A

B

C

D

1345678

8 7 6 5 4 3 2 1

E

F

E

F

A

SIZEMATERIAL

UNLESS OTHERWISE SPECIFIED:

REV.

TITLE:

GEOMETRIC TOLERANCING PER: ASME Y.14.5M-1994

DIMENSIONS ARE IN [MM] INCHES

TOLERANCES:FRACTIONAL: [1.5] 1/16"ANGLE: MACH 1/2 BEND 1X.X" (1 DECIMAL): [3] 0.1"X.XX" (2 DECIMAL): [1] 0.03"X.XXX" (3 DECIMAL): [0.5] 0.010"

SEE PARTS

PROJECT:

44147000

CFINISH

PART#

ALT. PART#

DO NOT SCALE DRAWING

TOTAL AUTOMOTIVE LIFTINGSOLUTIONS INC.

(905)847-1198 FAX (905)891-1214www.TLSLifts.com

A-01

SCALE: 1:24 SHEET 1 OF 9WEIGHT: 3875.83 lbs

THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF TOTAL AUTOMOTIVE LIFTING SOLUTIONS INC. (TLS).

ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION

OF TLS IS PROHIBITED.

PROPRIETARY AND CONFIDENTIAL

APPROVED

S.Z.DRAWN

DATE

NAME

CHECKED

2

TLS 15K 4 POST LIFT

44147000

15,000LBS 4 POST LIFT

2015-02-20THIRD ANGLE PROJECTION

Runway Step PlatformsP/N (4TMWS)

Stainless Steel TurnplatesP/N (4TSSTP)

Jacking BeamP/N (4TRJ7500)