manual 55030075

Toungporn Klinpong 55030075 Section 1

Daikin Room Air Conditioner (Model: AT09/13) Operation Manual

Warning

Caution

If you do not follow these suggestions strictly, the air conditioner can cause damage to asset, personal injury or death.

If you do not follow these suggestions strictly, the air conditioner may cause a minor or moderate damage to asset, or personal injury.

Never do.

Always follow the instructions.

Make sure to ground the air conditioner.

Do not allow the air conditioner (or remote controller) to get wet.

Do not touch the air conditioner (or remote controller) when your hand is wet.

Warning

- To avoid the risk of fire, explosion or injury, do not turn on the air conditioner in risk areas such as an area where flammable or corrosive gases are found. - Do not allow the air flow form the air conditioner to your body for a long time. - Do not put your finger or any object into the air outlet or inlet because the air fan is rotating at high speed. It can cause injury. - Do not attempt to repair, move, modify or reinstall the air conditioner by yourself. Incorrect work of the appliance can cause electric shocks, fire or other damage. - Consult your Daikin dealer for advice and information of repair and reinstallation.

Safety Precautions

- Keep this operation manual in a place where the customers can get it easily. - Read this operation manual carefully before using the air conditioner. - The customers must read this operation manual thoroughly for safety. - This operation manual is divided the precautions into warning and cautions. The customers must follow the precautions entirely because it is important for safety certification.


- Refrigerant used for the air condition is safe despite the leak of such substance. In case of the leak of refrigerant, make sure that this substance does not touch the flame of any heating device.

- If the air conditioner is not cooling, refrigerant may be leaking. You should contact your dealer and check the repair information from service officer. - Do not try to install the air conditioner by yourself. Incorrect installation can cause water leaks, electric shocks or fire. - To avoid electric shocks, fire or injuries, when finding unusual things, for instance, a smell of fire, stop using, pull down the circuit breaker and contact your dealer for suggestion. - It is necessary to install the ground circuit. If not, it can result in electric shocks or fire depending on the environment.

- Make sure to ground the air conditioner. Improper grounding may result in electric shocks. Do not connect the grounding wire to a gas pipe, water pipe, lightening rod or telephone ground line.

Caution - To avoid deterioration, do not use the air conditioner for cooling precision instruments, food, plants, animals or art works. - Never let little children, plants, animals get the air flow directly. - Never place any flammable electrical equipment to get the air flow directly or place under the air conditioner. It can cause incomplete combustion or deformation of the shape of the air conditioner. - Do not block the air outlets or inlets, weak air flow direction may cause working problems. - Do not stand, sit or place any object on the air conditioner. To avoid injury, do not remove the fan guard. - Do not place anything under the indoor or outdoor unit that must be kept away from moisture because in some cases, the moisture in the air may condense and drip. - After using for a long time, check the damage of unit stand and other object. - Do not touch the air inlets and the aluminum panels of the outdoor unit as it can cause injury. - This appliance is not suitable for children or impaired persons to use without proper supervision. - Little children should be in control of their parents to make sure that they will not play with the air conditioner. - Keep the remote controller away from infants and young children to prevent an accident as children accidentally swallow battery. - To avoid the lack of oxygen, the adequate ventilation in room is needed if the power point appliance is used with the air conditioner. - Turn off the appliance, pull down the breaker and unplug the power cord before cleaning. - Never connect the air conditioner with the power supply that differs from the set. It may cause problems or fire. - Place the sewer in a place where water can easily drain. Improper drainage may cause moisture to the building and furniture.


- Do not place any object near the outdoor unit and do not to let leaves and dust accumulate around the unit. Leaves may let small animals enter the unit. It can cause malfunction, smoke or fire if such animals contact with electric parts. - Do not use the air conditioner with wet hands.

- Do not wash the indoor unit with water; use only a slightly wet towel.

- Do not place things such as water containers, vases, flower plots or anything else on the top of the air conditioner. Water may drip into the unit and deteriorate electronic insulations, resulting in an electric shock.

Installation site If you want to install the air conditioner in these following places, ask for an advice from your dealer. - Places with a steam of oil. - Places where there is salt in the air such as coastal areas. - Places where there is sulfur such as hot spring. Waste water from the appliance must be released into a well-drained area.

Remote controller (AT09/13)

1. Signal transmitter 8. SWING button 2. Display 9. ON TIMER button 3. POWERFUL button 10. OFF TIMER button 4. TEMPERATURE adjustment buttons 11. TIMER SELECT button 5. ON/OFF button 12. TIMER CANCEL button 6. MODE selector button 13. CLOCK button 7. FAN setting button 14. RESET button


Preparation before Operation To set the batteries

1. Slide the front cover and take it off. 2. Set two dry batteries (AAA). 3. Set the front cover.

To use the remote controller

- To use the remote controller for sending signal to the air conditioner, if there is any object blocking the signals such as curtains, the air conditioner will not work.

- Do not throw the remote controller on the ground or make it wet.

- The maximum distance for sending signals is approximately 7 meters.

To fix the remote controller holder on the wall

- Chose a location where the signals can reach the unit. - Fix the holder to a wall, a pole or others with the screws

supplied with the holder. - Place the remote controller into the remote controller holder.

To set the clock

1. Press “CLOCK button”. - 0:00 is displayed. - The clock symbol on the display blinks. 2. Press “TIMER SELECT button” to set the current time.

- Holding down “” or “” to increase or decrease the time rapidly.

3. Press “CLOCK button” - The “:” blinks.

DRY, COOL, FAN Operation The air conditioner operates with the operation mode you choose. From now on, the air conditioner will operate with the same operation mode.

To start operation 1. Press “MODE selector button” and select the operation mode.

- Each pressing button will set the operation mode in sequence; dry, cool, and fan.

2. Press “ON/OFF button”. - The operation light will light up.


To stop operation

3. Press “ON/OFF button” again. - The operation light will be turned off.

To change the temperature setting 4. Press “TEMPERATURE adjustment buttons”.

Dry or Fan operation Cool operation

The temperature setting will not change.

Press “” to increase the temperature and press “” to decrease the temperature.

Set the temperature as required.

To change the wild rate setting 5. Press “FAN setting button”.

Dry operation Cool or Fan operation

The wild rate setting cannot be changed.

There are 5 levels to set the wild rate.

Timer Operation Timer functions are used for switching the air conditioner on or off at night or in the morning automatically. You can use both OFF TIMER and ON TIMER together.

To use OFF TIMER operation

Check that the clock is correct. If it is incorrect, set the current time. 1. Press “OFF TIMER button”.

- 0:00 is displayed. - The clock symbol on the display blinks.

2. Press “TIMER SELECT button” until it reaches the time you want. - Each pressing button will increase or decrease the time setting by 10 minutes. Holding down the button will change the time rapidly.

3. Press “OFF TIMER button” again. - The timer operation light will light up.

To cancel OFF TIMER operation 4. Press “TIMER CANCEL button”.

- The timer operation light will be turned off.

To use ON TIMER operation Check that the clock is correct. If it is in correct, set the current time.

1. Press “ON TIMER button”. - 6:00 is displayed. - The clock symbol on the display blinks.

2. Press ““TIMER SELECT button” until it reaches the time you want. - Each pressing button will increase or decrease the time setting by 10 minutes. Holding down the button will change the time rapidly.


3. Press “ON TIMER button” again. - The timer operation light will light up.

To cancel OFF TIMER operation 4. Press “TIMER CANCEL button”.

- The timer operation light will be turned off.

To combine ON TIMER and OFF TIMER This is an example for combining the two functions.

Present time: 23.00 (The air conditioner is still working) OFF TIMER at 0.00 ON TIMER at 7.00

Care and Cleaning Caution: Before cleaning, turn off the air conditioner and pull-down the circuit breaker.

The air conditioner The inside unit, outside unit and remote controller 1. Wipe this equipment with a soft dry cloth.

Front panel

1. Open the front panel. - Hold the handle bars of the front panel both sides and lift up until you hear the click sound. (picture 1)

2. Remove the front panel.

- Open the front panel while slide to either left or right and pull it toward you.(picture 2)

3. Clean the front panel.

- Wipe it with a soft cloth dipped in water.

4. Attach the front panel - Arrange three shafts of the front panel to match the slots. Then push all the shafts into the slots. (picture 4) - Gently push off the front panel, along with pressing three points.

Air filter 1. Open the front panel. (picture 1)

Combination


2. Pull out the air filters. - Push the filter handle at the center of each air filter. Then slightly upward and pull it down. (picture 2)

3. Take off the titanium apatite photocatalytic air-purifying filter. (picture 3.1)

4. Clean or change the air filters (picture 4)

5. Set the air filters and the titanium apatite photocatalytic air-purifying filter as they were. Then close the front panel. (picture 5)

Air filter 1. Wash the air filters with water or clean them with the vacuum cleaner.

- If the dust does not come off easily, wash them with neutral detergent thinned with warm water, then let them dry in the shade. - You should clean the air filters every 2 weeks.

Titanium apatite photocatalytic air-purifying filter The ability of air purification of the titanium apatite photocatalytic air-purifying filter can be

modified by cleaning with water every 6 months. It is recommended to change it every 3 years.

manual 55030075

Education