manual de recarga samsung clp 500 clp 550
Post on 12-May-2015
Embed Size (px)
DESCRIPTIONManual utilizado nos modelos Samsung para Impressoras CLP 500 | CLP 550.
- 1.CLP500_550_510TECHTechnical InstructionsPrinters OEM InfoTools & Supplies 1CORPORATE CLP-500, 500NCLP-500D5C Cyan Toner Yield @ 5%: 5,000pgsTools: CLP-500D5M Magenta Toner Yield @ 5%: 5,000pgs LOS ANGELES, USA CLP-550, 550NCLP-500D5Y Yellow Toner Yield @ 5%: 5,000pgs Needlenose PliersUS 1 800 394.9900 CLP-510, 510NCLP-500D7K Black Toner Yield @ 5%: 7,000pgs #2 Phillips head screw driverIntl +1 818 837.8100 CLP-511, 515, 560, 560NCLP-510D5C Cyan Toner Yield @ 5%: 5,000pgsSmall flat blade screw driverFAX 1 800 394.9910 CLP-510D5M Magenta Toner Yield @ 5%: 5,000pgs CLP-510D5Y Yellow Toner Yield @ 5%: 5,000pgsIntl +1 818 838.7047CLP-510D7K Black Toner Yield @ 5%: 7,000pgs Supplies: CLP-510D2C Cyan Toner Yield @ 5%: 2,000pgsTonerATLANTA, USA CLP-510D2M Magenta Toner Yield @ 5%: 2,000pgsUS 1 877 676.4223CLP-510D2Y Yellow Toner Yield @ 5%: 2,000pgs SwabsIntl +1 770 516.9488CLP-510D2K Black Toner Yield @ 5%: 3,000pgs Lint Free ClothFAX 1 877 337.7976Intl +1 770 516.7794DALLAS, USAUS 1 877 499.4989Intl +1 972 840.4989FAX 1 877 774.1750Intl +1 972 840.1750MIAMI, USA Photo 1US 1 800 595.429Step 1Intl +1 305 594.3396FAX 1 800 522.8640With the cartridge facing with developerIntl +1 305 594.3309roller towards you and cartridge label up,NEW YORK, USA remove the four Phillip screws from theUS 1 800 431.7884Intl +1 631 345.0121top cover. (Photo 1)FAX 1 800 431.8812Intl +1 631345.0690 SANFORD,USAUS 1 800 786.9049Intl +1 919 775.4584FAX 1 800 786.9049Intl +1 919 775.4584 TORONTO, CAN Photo 2CAN 1 877 848.0818Step 2Intl +1 905 712.9501 Rotate the cartridge right with theFAX 1 877 772.6773Intl +1 905 712.9502 larger developer roller drive gear facingBUENOS AIRES, ARG you. Remove the Phillip screw located inARG 0810 444.2656 the right bottom. Gently pry up andIntl +011 4583.5900remove the cover. (Photo 2)FAX +011 4584.3100 MELBOURNE, AUSAUS 1 800 003. 100Intl +62 03 9561.8102FAX 1 800 004.302Intl +62 03 9561-7751SYDNEY, AUSPhoto 3AUS 1 800 003.100Step 3Intl +62 02 9648.2630FAX 1800 004.302 Turn the cartridge so the fill cap end isIntl +62 02 9548.2635 facing you. Pry off the black developerMONTEVIDEO,URY gear end cap. Remove all three whiteURY 02 902.7206gears and the developer gear spacer,Intl +5982 900.8358FAX +5982 908.3816 taking note of orientation. (Photo 3)JOHANNESBURG, S.A.S.A. +27 11 974.6155FAX +27 11 974.3593 E-mail: [email protected] Website: www.futuregraphicsllc.com
2. 2 Samsung CLP500/550/510 Technical InstructionsPhoto 4Step 4Remove the e clip from the developerroller shaft and the bushing insert. Notes(Photo 4) Photo 5Step 5 OptionalRotate the cartridge to the opposite sidewith the developer bias circuit board fac-ing you. Remove the three Phillip screwson the circuit board and remove both thecontact and board. (Photo 5) Photo 6Step 6 OptionalRemove the two Phillip screws that holdthe gear train plate in place. The gears arenow easily removed. Only the gear on thedeveloper roller needs to be removed inorder to remove the developer roller drivegear. (Photo 6) NOTE: Mark gear order foreasy reassemble.Photo 7Step 7Pry off the black developer roller gear endcap. Remove the small flat washer, whitedeveloper roller drive gear and developergear spacer. (Photo 7)Step 8 Photo 8Rotate the cartridge so that the developerroller is facing you. Carefully pull the leftside of the developer roller shaft outwardenough to clear the housing. Once clear,pull the developer roller towards the leftand remove (be careful not to scratch thedeveloper roller surface). Note that thereare thin Mylar type washers on both sidesof the developer roller shaft -- dont losethem! (Photo 8) 3. Samsung CLP500/550/510 Technical InstructionsPhoto 9 Step 9 Rotate the cartridge so that the fill plug is facing you and remove. Clean out any remaining toner from the reservoir. Notes (Photo 9) Photo 10 Step 10 Taking the cleaned developer roller install it back into the cartridge with the longer shaft towards the gear set keeping it level. Take care that the thin Mylar washers set properly and do not get damaged. (Photo 10) Photo 11 Step 11 Turn the cartridge so that the gear train side is facing you. Reinstall the developer roller gear spacer, white developer roller drive gear and washer. Press on the black developer roller gear end cap. (Photo 11) Photo 12 Step 12 Replace the one white gear that was removed from the gear train, the gear train plate, developer bias circuit board and contact. The gear train plate requires two Phillip screws and the developer bias board and contact require three. (Photo 12) Photo 13 Step 13 Rotate the cartridge to the opposite end and reinstall the bushing, e clip, devel- oper roller gear spacer and the three white gears. Press on the black developer gear end cap. (Photo 13) 4. 4 Samsung CLP500/550/510 Technical Instructions Photo 14 Step 14 Fill the cartridge with toner and replace the fill cap. (Photo 14)Photo 16 Photo 15 Step 15 Replace the cover back onto the cartridge and reinstall the five Phillip screws. (Photo 15 & 16) The Samsung CLP-500, CLP-500N, CLP-550 and CLP-550N are color laser printers designed for businesses in the small to medium size range. The printers offer up to 5ppm color and 21ppm black and white with print resolution up to 1200 dpi. The printers include automatic built in duplexing, Hi-Speed USB connectivity and have options such as 500 sheet paper handling and network connectivity.Supplies for the printers come with starter toners, black at 2,000 pages and 1,500 for the color. Included are the waste toner container (3,000 pages), Imaging unit (50K/12K pages Black/Color) and the transfer belt (50K/12K pages Black/Color). Replacement toner cartridges are rated at black 7,000 pages and color 5,000 pages with the asterisk usage conditions and print patterns may cause results to vary.Future Graphics (FG) is a distributor of compatible replacement parts and products for imagining equipment. None of FG's products are genuine OEM replacement parts and no affiliation or sponsorship is to be implied between FG and any OEM.E-mail: [email protected] Website: www.futuregraphicsllc.com 5. CLP-500 Cartridge Reset SystemInstallation Instructions CLP500RESETPhoto 2 Attention: The following procedure requiresStep 2 experience in soldering electronic components. Hold the Cartridge Contacts Assembly in a vise orsimilar clamping device. Tool Requirements: Small Blade Screw Driver (See Photo 2) Needle Nose Pliers Small Vise Soldering Iron 600F to 800F temperature range, Conical tip recommended. Silver Solder Photo 3 PIN 3Photo 1PIN 1 Step 3 Remove the component soldered to the two outside contact tabs (pins 1 and 3). Step 1 Holding the wire with needlenose pliers on one side of the contact tab, apply the heated solder iron onto the other side of the tab. AsUsing a small blade screw driver, carefully remove the solder melts, gently pull the wire with the needle nose pliers.the Cartridge Contacts Assembly from the side of Warning: DO NOT OVER HEAT the tab because the plasticthe cartridge. housing is very easily melted. (See Photo 1)Repeat above instructions on the other outside contact tab.(See Photo 3)w w w. f u t u re g r a p h i c s l l c . c o m 1 REV. 10/02/05 CLPCRSTECH_ver.2 6. CLP-500 Cartridge Reset SystemInstallation Instructions Photo 4Photo 7 Step 4 Use solder iron to smooth and minimize the remain- ing solder on the contact tabs. Step 7 Warning: DO NOT OVER HEAT the tab because (Optional) Solder connectors to the contact tabs. the plastic housing is very easily melted. Warning: DO NOT OVER HEAT the tab because (See Photo 4) the plastic housing is very easily melted.(See Photo 6) Photo 5Photo 8Step 5Check tightness of connectors on the tabs.If loose, remove assembly from the tabs.Use needlenose pliers to tighten connector gapand reinstall onto the tabs. (See Photo 5)Step 8Reinstall Cartridge Contacts Assembly onto the car- Photo 6tridge. (See Photo 8) Need trustworthy, detailed Technical Instructionsfor another engine?V i s i t : w w w. f u t u re g r a p h i c s l l c . c o mStep 6Install Cartridge Reset System onto the two out-side contact tabs. (See Photo 6)Future Graphics (FG) is a distributor of compatible replacement parts andproducts for imagining equipment. None of FG's products are genuineOEM replacement parts and no affiliation or sponsorship is to be impliedbetween FG and any OEM. w w w. f u t u re g r a p h i c s l l c . c o m 2CLPCRSTECH_ver.2 7. CLP-510 Chip Replacement Procedure Installation InstructionsCLP-510 Chip Board Photo 2Part Numbers:CLP510CHIPK CLP510CHIPCCLP510CHIPM CLP510CHIPY Attention: The following procedure requires experience in soldering electronic components.Step 2 Hold the Cartridge Contacts Assembly in a vise or Tool Requirements:similar clamping device. Small Blade Screw Driver Needle Nose Pliers(See Photo 2) Small Vise Soldering Iron 600F to 800F temperature range, Conical tip recommended. Silver Solder Solder-WickPhoto 3CONTACT TAB 3Photo 1 CONTACT TAB 1Step 3Using the solder removal device and soldering iron,remove all solder holding the Chip Board to the con-tact tabs. Using a needle nose pliers, gently pull theChip Board from the contact tabs.Step 1(See Photo 3)Using a small blade screw driver, carefully removeIf the Chip Board is still attached to the contact tabs,the Cartridge Contacts Assembly from the side ofreheating the contact tab with soldering iron andthe cartridge.gently pull with the needle nose pliers.(See Photo 4)(See Photo 1)Warning: DO NOT OVER HEAT the tab because theplastic housing is very easily melted. w w w. f u t u re g r a p h i c s l l c . c o m1 REV. 10/31/05 CLP510CHIPTECH 8. CLP-510 Chip Replacement ProcedureInstallation InstructionsPhoto 4Photo 6Photo 5Step 5Reinstall Cartridge Contacts Assembly onto thecartridge. (See Photo 6)Step 4Position CLP-510 Chip Board notched areaclosest to the contacts. Solder contact tabs to theChip Board. (See Photo 5) Warning: DO NOT OVER HEAT the tab becausethe plastic housing is very easily melted. Need trustworthy, detailed Technical Instructionsfor another engine?V i s i t : w w w. f u t u re g r a p h i c s l l c . c o m Future Graphics (FG) is a distributor of compatible replacement parts andproducts for imagining equipment. None of FG's products are genuineOEM replacement parts and no affiliation or sponsorship is to be impliedbetween FG and any OEM. w w w. f u t u re g r a p h i c s l l c . c o m 2 REV. 10/31/05 CLP510CHIPTECH