manual fusion

The illustrations, technical information, data and descriptions contained in this publication,were correct at the time of going to print. We reserve the right to make any changesnecessary in line with continuous development and improvement.

This publication may not be duplicated, reprinted, stored in a data processing system ortransmitted by electronic, mechanical, photographic or other means, or recorded,translated, edited, abridged or expanded without the prior written consent of Ford-WerkeGmbH. The same also applies for parts of this manual and their use in other publications.

Although due care has been taken to make this publication as complete and accurate as

possible, it can still be subject to alterations.

This publication describes options and trim levels available throughout the Ford modelrange in every European country, and therefore some of the items covered may not applyto your vehicle.

Important: Ford genuine parts and accessories have been specifically designed for Fordvehicles. They are dedicated for your Ford vehicle.

We would like to point out that other parts and accessories than mentioned above have notbeen examined and approved by Ford unless explicitly stated by Ford. In spite ofcontinuous market product monitoring, we cannot certify the suitability of such products.Ford is not liable for any damage caused by the use of such products.

� Copyright 2005Issued by Ford-Werke GmbH, Ford Customer Service Division

Code No CG3441en LHD 07/2005

Contents

Quick start 2

Introduction 12

Instrumentation 14

Vehicle information systems 22

Climate controls 36

Lights 46

Driver controls 54

Locks (security) 64

Seating and safety restraints 77

Driving 98

Roadside emergencies 138

Cleaning 161

Maintenance 163

Capacities and specifications 172

Index 184

Quick start

2

STORAGE AREAS

Front storage compartment

• Press the button to open.

• To close, push the cover downuntil it engages.

Note: Avoid keeping heat-sensitiveobjects in the front storagecompartment.

Never drive with the frontstorage compartment lid

open. This will obscure yourvision out of the front screen.Before setting off, always ensurethat the lid is securely engaged.

Storage compartment

A storage compartment is providedunderneath the instrument panelon the drivers side.

Glove compartment

Card holder

Coin holders

Pen/pencil clip

Quick start

3

Under-seat storage

The storage box is located underthe front passenger seat.

• To open: Pull the front of the seatcushion up .

• Pull the seat cushion towards theinstrument panel .

• Lift the seat cushion to reveal thestorage area .

• To close, follow the above steps inreverse, making sure that you pushthe seat cushion downwards until itlocks into place.

Storage pockets

Driver’s seat

Rear seats

Quick start

4

Map pockets(front seats)

FOLDING THE REAR SEATCUSHION AND SEATBACKFORWARDS

• Slide the front seat forwards.

• Fold the seat cushion forwards.

• Lower the head restraints. Pullthe locking handle on the rearseatback and fold the seatbackforwards .

• Press the rear of the seatbackdown to create a level surface .

• When returning the seats to theiroriginal positions, make sure theseat belts will function properly andare positioned in front of theseatback.

Quick start

5

MULTIFUNCTION DISPLAY

For details, refer to page 20onwards.

Distance to empty ordigital clock

To toggle between distance toempty and the clock, briefly pressthe right-hand button on theinstrument cluster.

Depending on the audio systemfitted, the clock is displayed onlywhile the right-hand button ispressed. Displaying the clockpermanently and the setting of theclock is available on the audiosystem only.

Tripmeter

To reset, press and hold theleft-hand button on theinstrument cluster.

Odometer

MESSAGE CENTRE

For details, refer to page 20onwards and page 22 onwards.

The display shows:

Gear display

(vehicles with automatictransmission or Durashift EST)

Clock or the audio system display

(depending on the audio systemequipped, if the audio system isswitched on or off and theindividual Message Centre settings)

Outside air temperature

Tripmeter

Odometer

Display warning light

The warning light accompanies thewarning and info messages andilluminates red or amber.

Quick start

6

Functions of the main menu

Press the RE/SET button briefly toscroll through the following menufunctions:

• Distance to empty

• Average speed

• Average fuel

• Fuel economy(depending on country)

• Time setting(when the vehicle is stationaryand depending on audio systemfitted)

• Individual settings(when the vehicle is stationary)

• Warning and info messages

Press and hold the RE/SET buttonto change or reset the desiredfunction or to enter the settingsmenus.

Personalised settings

The following personalised settingsare available on the MessageCentre:

• Remote unlocking

The vehicle can be set to unlockonly the driver’s door or to unlockall doors when the button ispressed once.

• Lane change indicators

The direction indicators can be setto flash three times when themultifunction lever is tapped up ordown.

• Radio display

The Message Centre can displaysome audio system information.

• Hazards on heavy braking

The hazard light can be set to flashautomatically if the brakes areapplied abruptly (e.g. emergencybraking).

• Chimes

Some of the convinience chimescan be deactivated.

• Language menu

Different languages can be chosento be used for the display.

Quick start

7

CLIMATE CONTROLS

For details, refer to chapterClimate controls, page 36 onwards.

Screen defrosting/demisting

Set the blower to position 3 or 4,select the maximum temperatureand set the air distribution controlto . Switch on the airconditioning (if equipped) tosupport demisting.

If necessary, switch on

the heated front screen and

the heated rear screen.

On vehicles with ElectronicAutomatic Climate Control pressthe button. This will activatethe heated screens as well asselecting the maximumtemperature and blower speed.

If the button is pressed again,the system returns to the previoussetting. The heated screens switchoff automatically after a short time.

Quick start

8

Rapid cooling of the vehicleinterior

Set the blower to position 4, selectthe minimum temperature and setthe air distribution control to .Switch on the air conditioning andrecirculated air.

If the windows start to mist up afterrapid cooling, switch off therecirculated air.

On vehicles with ElectronicAutomatic Climate Control pressthe AUTO button. The ElectronicAutomatic Climate Control adjuststo the current circumstancesautomatically.

LOCKS (SECURITY)

For details, refer to chapter Locks

(security), page 64 onwards.

Locking/unlocking the vehicle

Press once to activate centrallocking and arm the anti-theftalarm system (if equipped)

Press twice within threeseconds to activate doublelocking and arm the anti-theftalarm system (if equipped)

Press once to unlock thevehicle. For personal settings,refer to sectionReprogramming the

unlocking function, page 70.

Press twice withinthree seconds to unlock/openthe tailgate only.

Note: The doors cannot be openedfrom inside the vehicle when doublelocking is activated.

Quick start

9

AUDIO SYSTEMS

For details, refer to the separatemanual.

Automatic volume control (AVC)

This function increases ordecreases the volume of the audiosystem relative to the vehiclespeed. For personal settings, referto the separate manual.

Setting the time and date

To enter the settings mode pressthe CLOCK button on the audiosystem.

Press the � or � button to togglebetween time and date.

To set the time/date turn the rotarycontrol.

Press the CLOCK button to savethe setting and exit the settingsmode.

DIESEL LOW FUEL SAFETYMODE

Diesel engines must never run outof fuel. They have safety devices toprevent this. They will reduceengine power by up to 30 % when alow fuel level is detected, asindicated by the low fuel warninglight.

The system will also shut down (i.e.the engine will stop completely)just prior to reaching zero fuel toprevent re-starting problems and,more importantly, severe enginedamage.

To start the engine, see the sectionDiesel low fuel safety mode onpage 124.

Benefits of the diesel low fuelsafety mode

This mode maximises fuelefficiency under very low fuelconditions and helps to prevent:

• Running out of fuel too quickly

• Clogging the fuel system

• Placing excess pressure on theengine, that would result in costlyand severe engine damage

Quick start

10

ELECTRICAL FEATURES

Autolamps


When the exterior light switch is setto position AUTO, the dipped beamheadlights will switch on and offautomatically depending on theambient light. The Autolamps areactivated only when the ignition isswitched on (position II).

Home safe light

For details, refer to page 48.

With the ignition switched off theheadlights can be switched on andwill be switched off automaticallyafter a period of time.

On vehicles with Autolamps:

turn the exterior lights switchfrom the position to positionAUTO and back to position within 2 seconds, or

turn the exterior lights switchfrom the position AUTO toposition and back to positionAUTO within 2 seconds.

On vehicles without Autolamps:

turn the exterior lights switchfrom the position toposition and back toposition within 2 seconds, or

turn the exterior lights switchfrom the position toposition and back toposition within 2 seconds.

Quick start

11

Welcome lights


The side and tail lights will switchon automatically for 25 secondswhen the door is unlocked usingthe remote control. Once all doorsare closed, the welcome lights willswitch off automatically after5 seconds or at once if the ignitionis switched on.

Autowipers/intermittent wiping


Depending on the model variant,auto wipers or intermittent wipingare selected by moving the wiperlever one position upwards.

When the ignition is switched onwith the wiper lever in theAutowipers position, the wipers willnot cycle until water is detected onthe front screen.

Select the wipe interval or the rainsensor sensitivity of the auto wiperswith the rotary switch:

1 = Short time interval/high sensitivity

6 = Extended time interval/low sensitivity

Power folding mirrors


With the interior switch in thecentre position, push the controlunit down to fold the mirror. Toreturn the door mirror to its originalposition push the control unit downagain.

Press the button once to lock thevehicle: the door mirrors will foldautomatically if they are not alreadyfolded back using the control unit.

Press the button once to unlockthe vehicle: the door mirrors willunfold automatically if they wereautomatically folded back.

Introduction

12

PREFACE

Congratulations on acquiring yournew Ford. Please take the time toget well acquainted with yourvehicle by reading your ownerliterature. The more you know andunderstand about your vehicle thegreater the safety, economy, andpleasure you will derive fromdriving it.

The Owner’s Handbook describesevery option and model variantavailable in every Europeancountry and therefore some of theitems covered may not apply toyour particular vehicle.Furthermore, due to printingcycles it may describe optionsbefore they are generallyavailable.

Regular servicing of your vehiclehelps maintain both its road-worthiness and its resale value. Anetwork of more than 7 000 Fordauthorized repairers throughoutEurope can help you with theirprofessional servicing expertise.

Their specially trained personnelare best qualified to service yourvehicle properly and expertly. Also,they are supported by a wide rangeof highly specialised tools andequipment specially developed forservicing Ford vehicles.

Remember to pass on theOwner’s Handbook when

reselling the vehicle. It is anintegral part of the vehicle.

Introduction

13

FOR YOUR SAFETY AND ENVIRONMENTAL PROTECTION

Warning symbols inthis handbook

How can you reduce the risk ofpersonal injury and preventpossible damage to others, yourvehicle and its equipment? In thishandbook, answers to suchquestions are contained incomments highlighted by thewarning triangle symbol.

Note: Important information is alsogiven in paragraphs starting withthe highlighted word Note.

Warning symbols onyour vehicle

When you see thissymbol, it is imperativethat you consult therelevant section of this

handbook before touching orattempting adjustment of any kind.

RUNNING IN

Avoid driving too briskly during thefirst 1 500 km. Vary the speedfrequently and change up a gearearly. Avoid labouring the engine.

New tyres require a running-indistance of approximately 500 km.During this period, the car mayexhibit different drivingcharacteristics. Therefore, avoiddriving too briskly during the first500 km.

If possible, you should avoid heavyuse of the brakes for the first150 km in town and for the first1 500 km on motorways.

From 1 500 km onwards you cangradually increase the performanceof your vehicle up to the permittedmaximum speeds.

We wish you safe and pleasurabledriving with your Ford vehicle.

Instrumentation

14

Position Description See page

Side window demister 36

Ventilation vents 36

Luggage compartment release 66

Multifunction lever: direction indicators,main beam, message centre

51-52, 22

Instrumentation

15


Instrument cluster 16-21

Wiper lever 55-57

Heated front screen switch 45

Heated rear screen switch 45

Front storage compartment 128

Hazard flasher switch 138

Electronic Stability Program (ESP)1 101-102

Coin holder1 130

Airbag deactivation light1 91-92

Coin holder1 130

Audio systems/navigation system:see the separate manual

–

Heating/ventilation/air conditioning 36-45

Interior temperature sensor2 42

Ignition switch 102

Horn 54

Steering wheel adjustment 54

Audio remote control 58

Headlight levelling control 50

Storage compartment 128

Exterior lights/front fog lights/rear fog lights

46-50

1 Depending on model variant.2 Vehicles with Electronic Automatic Climate Control.

Instrumentation

16

WARNING AND INDICATOR LIGHTS IN THE INSTRUMENT CLUSTER

Position Symbol Function See page

Transmission/Engine systems fault warning light

1131, 122

ESP indicator light 101-102

Airbag/seat belt pretensioner warning light

91

Direction indicator light 52

Engine immobilisation systemindicator light

73

Instrumentation

17

Position Symbol Function See page

Ignition warning light 156

Headlight indicator light 47

Main beam indicator light 52

Frost warning light 124

Doors open warning light2 67

Rear fog light indicator light 48

Low fuel level warning light 124

Brake system warning light 98, 99, 168

Oil pressure warning light 168

Power assisted steering warning light3 123

Overdrive indicator light1 109

Glow plug indicator light 104

Front fog light indicator light 47-48

Engine warning light 123

ABS warning light 99

1 Vehicles with automatic transmission.2 Depending on model variant.3 Vehicles with 1.6 l Duratorq-TDCi engine.

Instrumentation

18

The following warning and indicatorlights illuminate when the ignitionis switched on:

• ABS(depending on model variant)

• Airbag/seat belt pretensioner

• Brake system

• Doors open(depending on model variant)

• Engine

• Engine immobilisation

• ESP(depending on model variant)

• Frost

• Ignition

• Oil pressure

• Power assisted steering (vehicles with 1.6 l Duratorq-TDCiengine)

• Transmission/engine systems

If a warning or indicator light doesnot illuminate when the ignition isswitched on, it indicates amalfunction. Have the systemchecked by an expert.

Instrumentation

19

GAUGES

Tachometer

On vehicles with a diesel engine,the tachometer goes to6 000 revolutions per minute.

Engine coolant temperaturegauge

At normal operating temperature,the temperature indicator remainswithin the centre section.

If the needle enters the red sectionand/or the Engine coolanttemperature warning appears, theengine is overheating.

Switch off the ignition anddetermine the source of theproblem once the engine has cooleddown.

Refer also to section Cooling

system reservoir, page 169.

Fuel gauge

The arrow adjacent to the fuelpump symbol indicates on whichside of the vehicle the fuel filler capis located.

Speedometer

Instrumentation

20

Multifunction display orMessage Centre

Depending on the model variant,the vehicle is equipped with amultifunction display or a displayfor the Message Centre.

The display is activated when thedriver’s door is opened or theignition is switched on.

With the ignition switched off(position 0) and the key removed,the display will be automaticallydeactivated after approximately10 minutes.

Multifunction display(depending on vehicle variant)

Distance to empty and digitalclock

Press the right-hand button onthe instrument cluster briefly totoggle between the displays.

• Distance to empty

Indicates the approximate distancethe vehicle will travel on the fuelremaining in the tank. Changes indriving pattern may cause the valueto vary.

• Digital clock

Note: Depending on the audiosystem fitted, the clock is displayedonly while the right-hand button is pressed. Displaying the clockpermanently and the setting of theclock is available on the audiosystem only. Please see chapterQuick start, page 9, or the separatemanual.

The setting of the clock is onlypossible when the vehicle isstationary.

Instrumentation

21

To set the time:

• Turn the ignition key toposition II.

• Press and hold the right-handbutton until the time displayflashes.

• To advance the time, press theright-hand button briefly. Eachpress advances the time by oneminute.

To advance rapidly, hold thebutton pressed.

Tripmeter

The tripmeter can register themileage of individual journeys.

To reset, press and hold theleft-hand button beneath thedisplay.

Note: If Sh on appears in thedisplay instead of the tripmeter, theshipping mode of the vehicle’selectric system is activated. Pleasecontact your dealer to deactivatethis mode.

Odometer

Registers the total mileage of thevehicle.

Message Centre(depending on model variant)

Gear display

For information, refer to the sectionGear display, page 107 (vehicleswith automatic transmission) orpage 116 (vehicles with DurashiftEST).

Clock or the display of the audiosystem


Tripmeter

Odometer

Display warning light

For further information about theMessage Centre, refer to thechapter Vehicle information

systems, page 22 onwards.

Vehicle information systems

22

MESSAGE CENTRE

Switch on the ignition (position II)to activate the Message Centre.

Various systems can beprogrammed using the MessageCentre and the multifunction leveron the steering column.

The Message Centre also provideswarning messages about faults orsystem malfunctions. For furtherdetails, refer to the sectionWarning/information messages,page 26.

For road safety reasons, setand reset the functions only

when the vehicle is stationary.

Note: The displays depend on theequipment fitted and thereforecertain displays may not appear inthe Message Centre of yourparticular vehicle.

The display is activated when thedriver’s door is opened or theignition is switched on.

With the ignition switched off(position 0) and the key removed,the display will be automaticallydeactivated after approximately10 minutes.

Note: If SHIP ON appears in thedisplay, the shipping mode of thevehicle’s electric system isactivated. Please contact yourdealer to deactivate this mode.

Controls

Press the RE/SET button briefly totoggle between the displays.

Press and hold the RE/SET buttonto reset, to choose a submenu, or toadjust the settings.

If all chimes are activated, a shorttone will sound to confirm a resetor a selection.


23

Menu Display/sub-menu See page

Overview 24

Outside air temperature 25

Odometer/Tripmeter 25

Distance to empty 25

Main menu Average speed 25

Average fuel consumption 25

Fuel economy 25

Warning/information messages 26

Time setting 30

Overview 31

Remote unlock mode 33

Lane change indicators 33

Radio display 33

Settings menu Hazards on heavy braking 33g

Chime deactivation 34

Language setting 34

Measure units 35

Settings − exit 35


24

Main menu

WARNING/INFOMESSAGES


25

Press the RE/SET button briefly totoggle between the displays.

Press and hold the RE/SET buttonto reset or to choose a sub-menu.


Shows the outside air temperature.

See also section Frost warning,page 124.

Tripmeter

To reset, press and hold theRE/SET button.

Odometer

Distance to empty

Indicates the approximate distancethe vehicle will travel on the fuelremaining in the tank. Changes indriving pattern may cause the valueto vary.

Refer also to the section Low fuel

level warning on page 124.

Average speed

Indicates the average speedcalculated over the last 1 000 km orsince last reset.


Average fuel consumption

Indicates the average fuelconsumption since the function waslast reset.


Fuel economy(depending on country)

Indicates the instantaneous fuelconsumption of the vehicle.


26

Warning/information messages

Each time a warning messageappears in the display, the drivermust acknowledge it by pressingthe RE/SET button. The displaythen returns to the one previouslyshown.

Repeat this if further warningmessages appear.

Information messages do not haveto be acknowledged and willdisappear automatically after ashort period of time.

Once acknowledged, the warningmessage(s) will appear in the Mainmenu in the positionWARNING/INFO MESSAGESshown in the diagram on page 24and keep present until the problemhas been solved.

When scrolling through the Mainmenu, the warning messages willappear one after the other forapproximately two seconds eachand do not have to beacknowledged with the RE/SETbutton.

The messages are supplemented bya warning light next to the display,some additionally by the textPLEASE CHECK OWNER’SGUIDE.

Information messages are indicatedby the warning light illuminatingamber.

Warning messages are indicated bythe warning light illuminating red.

If a warning/information messageaccompanied by the warning light ispresent, the warning light willremain illuminated.


27

MessageWarning

lightSystem

Seepage

red Brakes98,

99

red Cooling system 19, 169

redAutomatictransmission, DurashiftEST

113,122

red Power steering 123

amber/red

Engine 123

amber/red

Driving 124

amber Automatic transmission 113

amber Lights 52

amber Lights 52


28

MessageWarning

lightSystem

Seepage

amber Locks 67

amber Locks 67

amber Locks 67

amber Locks 67

amber Locks 67

amber Locks 67

amber Locks 72

amberExterior lights, screen wiping/washing

46-47,55-56


29

MessageWarning

lightSystem

Seepage

amber Durashift EST 105-106

amber Durashift EST 105-106

amber Durashift EST 120



amber Lights 48

amber Voice control –1



1 See separate manual.


30

Time setting

Note: On vehicles with acompatible audio system, settingthe time is only possible via theaudio system. Please see chapterQuick start, page 9, or the separatemanual.

The menu is only available whenthe vehicle is stationary.

• Press and hold the RE/SETbutton to open the menu.

The hours flash.

• To advance the hours, press theRE/SET button briefly. Each pressadvances the time by one hour.

• To change to the minutes, pressand hold the RE/SET button.

The minutes flash.

• To advance the minutes, press theRE/SET button briefly. Each pressadvances the time by one minute.

• To change to the date, press andhold the RE/SET button.

The day flashes.

• Repeat the procedure used forhours and minutes to set the day,the month and the year.

• To exit the menu after selectingthe year, press and hold theRE/SET button.

• Press and hold the RE/SETbutton to save the settings and toclose the menu.

• Press the RE/SET button brieflyto return to the time settingwithout saving any changes.

The menu is left automaticallywithout saving any changes, if theRE/SET button is not pressed forapproximately 20 seconds.


31

Settings menu

Note: For road safety reasons,changes in the Settings menu canonly be made while the vehicle isstationary. If this menu or one of itssub-menus is open when thevehicle begins to move, the MessageCentre will automatically exit theSettings menu.


For an overview of the functionsavailable, see page 32.

• Press the RE/SET button brieflyto toggle between the displays.

• When the corresponding displayappears press and hold the RE/SETbutton to adjust the settings.

If the RE/SET button is notpressed for about 7 seconds, thismessage is shown to remind you ofthe procedure.

• If you changed a setting, amessage like this appears in thedisplay as confirmation.

• The settings will be savedpermanently to the MessageCentre.


32

Setting menu displays

• Press and hold the RE/SET button to enter the Settings menu.

• Press the RE/SET button briefly to toggle between the displays.

• When the corresponding display appears press and hold the RE/SETbutton to adjust the settings.


33

Remote control unlockingfunction

ALL DOORS: all doors will beunlocked when the button on theremote control is pressed once.

DRIVER ONLY: only the driver’sdoor will be unlocked when thebutton is pressed once.

For further information about thisfeature, see sectionReprogramming the unlocking

function, page 70.

Lane change indicators

3 FLASHES: if the multifunctionlever is tapped up or down, thedirection indicators will flash threetimes.

1 FLASH: the lane changeindicators function is deactivated.

For further information, see sectionMultifunction lever, page 51.

Radio display(depending on the audio systemequipped)

IN CLUSTER: the display of theaudio system is repeated in themessage centre display.

RADIO ONLY: the radio display inthe message centre is deactivated.

For further information about audiosystems see the separate manual.

Hazards on heavy braking(depending on country)

ENABLED: if the brakes are appliedabruptly (e. g. in case of anemergency braking), the hazardlights will automatically flash for aminimum of three times.

DISABLED: the feature isdeactivated.

For further information about thisfeature, see section Hazards on

heavy braking feature, page 100.


34

Chimes

ALL: all chimes are activated.

MINIMAL: the following chimes aredeactivated:

• RE/SET button pressconfirmation.

• Low outside temperature warningat temperatures under +4 ºC.

• Distance to empty warning atremaining fuel for 80, 40 and 20 km.

Setting the language


• Press the RE/SET button brieflyto toggle between the languages.

• When the desired language ismarked, press and hold theRE/SET button.


35

• When the message like thisappears, press and hold theRE/SET button to confirm and toreturn to the Settings menu.

• Press the RE/SET button brieflyto stay in the Language menuwithout changing the setting.

If the button is not pressed forapproximately 5 seconds, thedisplay returns to the Settingsmenu. Any changes to the languagesettings will not be saved.

Measure units

Imperial measure units (miles, mpg,mph) are only available with thelanguage setting ENGLISH MLS.

All other language settings usemetric measure units (km,l/100 km, km/h).

Settings menu – Exit

To exit the Settings menu, scroll tothis display and press and hold theRE/SET button.

The Settings menu is leftautomatically, if the RE/SET buttonis not pressed for approximately20 seconds. Any changes to thesettings will be saved.

Climate controls

36

HEATING, VENTILATION ANDAIR CONDITIONING

Outside air

Always keep the air intakes forwardof the front screen free of snow,leaves etc., to allow the system tofunction effectively.

Recirculated air (if equipped)

When recirculated air is selected,only the air currently in thepassenger compartment will becirculated. Outside air will not enterthe vehicle.

Note: It is not recommended to userecirculated air for more than30 minutes as there is no airexchange and the windows maymist up.

Fresh air filter/active carbonfilter (if equipped)

The fresh air filter removes mostpotentially harmful particles suchas pollen, industrial fallout and roaddust from entering the vehicle’sinterior. The active carbon filterremoves odours.

In an automatic car wash, youshould switch off the ventilationblower or switch to recirculated air(if equipped) to prevent the filtercollecting wax deposits.

Blower

The blower motor produces theventilation air flow and may emitnoises.

Side window demisters

When driving these vents provide aconstant air stream to the sidewindows. This helps to keep theside windows free of mist and ice.

Centre and side vents

The centre and side vents enableefficient ventilation of thepassenger compartment and shouldbe used when the cooling of thecompartment is required.

Climate controls

37

The side vents can also be used toremove mist and ice from the sidewindows. Make sure not to adjustthem straight upwards as they canalso divert the air stream comingout of the side window demisters(see also position on theinstrument panel overview, page 14onwards).

In winter, after the passengercompartment has been warmed up,the air from the centre vents has alower temperature than the air fromthe side vents. According toindividual preferences, the centrevents can be closed in cold weather,or opened for extra fresh air whenheating.

Heating

The heating depends upon thecoolant temperature and istherefore only effective when theengine is warm.

Air conditioning(if equipped)

The air is directed through theevaporator/heat exchanger where itis cooled if the air conditioning isswitched on. In addition, humidityis extracted from the air to helpkeep the windows free of mist.

The resulting condensation isdirected to the outside of thevehicle. It is therefore quite normalif you notice a small pool of waterunderneath the parked vehicle.

Note: The air conditioning systemonly operates when thetemperature is above +5 ºC, theengine is running and the blower isswitched on. Operating the airconditioning leads to higher fuelconsumption. However, alsoopening windows for additionalcooling leads to increased fuelconsumption, especially at higherroad speeds.

General notes on controlling theclimate in the vehicle’s interior

Close all the windows completely.

To warm the interior effectively,direct the heated air to the footwellarea. In very cold or humid weather,direct air towards the front screenand side windows as necessary toprevent from misting or icing.

To cool the interior effectively,direct the cooled air from thecentre and side vents towards theface level.

Climate controls

38

CONTROLS

If your vehicle is equipped with anElectronic Automatic ClimateControl, please see thecorresponding section, page 41onwards.

Blower

The blower is off in the 0 position.

To increase the blower speed,select a higher number.

With the blower turned off, theventilation air flow depends only onthe road speed and window mistingmay occur under adverseconditions.

Adjusting the temperature

Blue: Cold

Red: Warm

Air distribution control

Directs the main air flow as follows:

Front screen

Footwell/front screen

Face level

Face level/footwell

Footwell

Front screen/face level/ footwell

A minor portion of the air flow isalways directed towards the frontscreen.

The air distribution control can beset to any position between thesymbols.

Climate controls

39

HEATING AND VENTILATION

Rapid screen defrosting/demisting

Select maximum temperature, setthe air distribution control to and the blower to position 3 or 4.

Switch on the air conditioning (ifequipped) to support demisting.

If necessary, turn the heated rearand front screens on (see page 45).

Ventilation

Set the air distribution control tothe positions , or . Set theblower to any position. Open thecentre and side vents to suitindividual requirements.

Rapid heating of vehicle interior

Climate controls

40

MANUAL AIR CONDITIONING

Switching the air conditioningon/off

To switch the cooling effect on andoff, press the A/C switch.

If the blower is turned to position 0,the air conditioning will turn off.When the blower is turned on again,the air conditioning will reactivateautomatically.

Switching the recirculated airon/off

Press the button to toggle betweenoutside air and recirculated interiorair.

Cooling with outside air

It is recommended to cool thevehicle with the air distribution setto or .

In warm and humid weather,directing cooled air to the frontscreen may lead to a smallamount of condensation on theoutside surface of the front screen.

Rapid cooling of the vehicleinterior

After the vehicle has parked in thesun, drive with the windows openfor a short while, to exchange thehot air in the interior with cooleroutside air. Afterwards, the airconditioning system can be usedmore efficiently.

For rapid cooling, switch onrecirculated air and select .

Climate controls

41

Reducing air humidity inposition

Switching the air conditioning onextracts humidity from the air anddemists the windows faster.

ELECTRONIC AUTOMATICCLIMATE CONTROL

The temperature, amount anddistribution of the air flow arecontrolled automatically andadjusted according to the drivingand weather conditions. Pressingthe AUTO button switches on theAUTO mode.

The recommended system settingsfor all seasons are 22 °C and AUTOmode (the air conditioning isswitched on).

The individual settings can beadjusted as necessary.

To return to AUTO mode, press theAUTO button.

Avoid adjusting the settings whenthe vehicle interior is extremely hotor cold. The Electronic AutomaticClimate Control adjusts to thecurrent circumstancesautomatically.

Climate controls

42

For the system to function properlyand without restrictions, the sideand centre vents should be fullyopen, especially in summer.

The sensor which measures theinterior temperature is locatedunderneath the climate controlpanel in the centre console (seealso position on the instrumentpanel overview, page 14 onwards).

The sunload sensor is located ontop of the instrument panel. Thesensors should not be covered byany objects.

At low outside temperatures, whenthe system is in AUTO mode, theair stream will be directed to thefront screen and the side windowsas long as the engine is cold. Theheating of the passengercompartment will commence assoon as a minimum air temperaturecan be delivered by the engine orby the auxiliary heater (wherefitted).

Setting the temperature

Blue button: lower temperature.

Red button: higher temperature.

The temperature can be setbetween 16 °C and 28 °C in steps of0.5 °C using the buttons. In positionLO (below 16 °C) the system willswitch to permanent cooling, in HI(above 28 °C) to permanentheating, and not regulate a stabletemperature.

Climate controls

43

Setting the blower speed

Press the left-hand button toreduce the blower speed and thusthe amount of air.

Press the right-hand button toincrease the blower speed and thusthe amount of air.

The blower setting is indicated inthe display.

Setting the air distribution

Directs the air flow as follows:

Footwell

Face level

Front screen

Any combination of settings , and can be selectedsimultaneously.

Screen defrosting/demisting

As long as the button isselected, recirculated air cannot beselected and the air conditioningcannot be switched off. The blowerspeed and temperature are set tomaximum performanceautomatically and cannot beadjusted manually.

When is selected, the heatedscreens switch on automatically.

If the button is pressed again,the system returns to the previoussetting. The heated screens switchoff automatically after a short time.

Switching the recirculated airon/off

Press the button to toggle betweenoutside air and recirculated interiorair. The light in the button indicatesoperation.

Climate controls

44

Automatic recirculated aircontrol

When the system is in AUTO modeand the interior and exteriortemperatures are quite hot,recirculated air is selectedautomatically to maximise coolingof the interior.

Once the selected temperature isreached, the system willautomatically change to the outsideair position. The indicator light inthe button does not illuminateduring the automatic operation.

Switching the air conditioningon/off

Press the A/C button to switch theair conditioning on/off. A/C OFF appears in the displaywhen the air conditioning isswitched off. A/C appears in the display whenthe air conditioning is switched on.

Switching the ElectronicAutomatic Climate Controlon/off

Press OFF to switch off theElectronic Automatic ClimateControl. The settings remain stored.

The heating, ventilation and airconditioning system is switched offand recirculated air is selected.

Note: This setting is recommendedonly when driving with the windowsand/or sunroof open. This ensuresthat the automatic function doesnot work against the additional airflow through the windows and/orsunroof.

Press OFF again or AUTO to switchthe system back on. If anotherbutton is pressed, the storedsettings will be changed accordinglywhen the system is switched on.

Climate controls

45

HEATED FRONT AND REARSCREEN

Use for quick defrosting ordemisting of the front or rearscreen. It should be switched ononly if necessary.

On vehicles with ElectronicAutomatic Climate Control, when

is selected, the heated screensswitch on automatically and switchoff after a short time.

Heated front screen switch

The system operates only when theengine is running.

Press the switch to turn on or off.The light in the switch indicatesoperation.

The heating system switches offautomatically after 4 minutes.

Heated rear screen switch

Switch on the ignition first.

Press the switch to turn on or off.The light in the switch indicatesoperation.

Electrically operated door mirrorsalso have a heating element to clearthe glass. This system operateswhen the heated rear screen isswitched on.

The heating system switches offautomatically after a short period.

AUXILIARY HEATER(vehicles with a diesel engine −depending on country)

The auxiliary heater aids inwarming the interior compartmentand also the engine on vehicles withdiesel engines. It delivers warm airquickly after engine start, even ifthe engine is not warmed up yet. Itis automatically switched on or offdepending upon the outsidetemperature, the coolanttemperature and the alternatorload.

Lights

46

EXTERIOR LIGHTS

An audible signal will be heard ifthe driver’s door is opened with theexterior lights switched on and theignition switched off.

Exterior lights switch

Lights off

Side and tail lights

Headlights

The headlight beam directionshould be altered to suit driving onthe left- or right-hand side of theroad. Please consult an expert.

AUTO Autolamps(depending on model variant)

When the light switch is set toposition AUTO, the dipped beamheadlights will switch on and offautomatically depending on theambient light. The Autolamps areactivated only when the ignition isswitched on (position II).

The Autolamps feature is anauxiliary system which is not

intended to relieve the driver ofhis responsibility for the vehicle’sexterior lighting.

Note: In AUTO mode, main beamcan be activated only when theAutolamp feature has turned on theheadlights.

Lights

47

In AUTO mode, if the headlights gooff automatically with main beamactivated, the next time theAutolamp feature turns on theheadlights main beam will still beon. Dipped beam may be selectedby pulling the multifunction levertowards the steering wheel. Referto the section Multifunction lever,page 51 onwards.

Note: It is not possible to switch onthe front or rear fog lights when theexterior lights control is set toAUTO. To switch on the frontand/or rear fog lights, turn on theheadlights by setting the control toposition .

On vehicles with a Message Centre,if this message appears in thedisplay and the display warninglight illuminates amber, it indicatesa malfunction.

Switch the headlights on (position) and off (position ) manually

and have the system checked by anexpert.

Headlight indicator light

The headlight indicator lightilluminates when the headlights orthe side and tail lights are on.

Front fog lights

Switch on the headlights (position ) and pull out thecontrol switch one position.

The indicator light in theinstrument cluster will illuminatewhen the front fog lights are in use.The front fog lights should beused only when visibility isconsiderably restricted by fog,snow or rain.

Lights

48

Front and rear fog lights

Switch on the headlights (position ) and pull out thecontrol two positions.

On vehicles not equipped with frontfog lights the control switch can bepulled out only one position.

Both indicator lights in theinstrument cluster will illuminatewhen the front and rear fog lightsare switched on.

The rear fog lights mayonly be used when visibility

is restricted to less than 50 m andmust not be used when it israining or snowing.

Home safe lights

Within the first 10 minutes after theignition is switched off theheadlights can be switched on.They will then be switched offautomatically after a period of time.

On vehicles with Autolamps,

turn the exterior lights switchfrom the position to positionAUTO and back to position within 2 seconds, or

turn the exterior lights switchfrom the position AUTO toposition and back to positionAUTO within 2 seconds.

Lights

49

On vehicles without Autolamps,

turn the exterior lights switchfrom the position toposition and back toposition within 2 seconds, or

turn the exterior lights switchfrom the position toposition and back toposition within 2 seconds.

In addition, on vehicles with aMessage Centre, this message willappear in the display and thedisplay warning light illuminatesamber.

The lights will switch offautomatically:

• as soon as the exterior lightsswitch is turned to any position,

• as soon as the ignition is switchedon (position II),

• as soon as any door or the tailgateis unlocked using the remotecontrol,

• after 3 minutes, if any door or thetailgate is open, or

• after 30 seconds if all doors andthe tailgate are closed.

Welcome lights

Depending on model variant, theside and tail lights are switched onautomatically when the vehicle isunlocked using the radio frequencyremote control.

The lights switch off automatically

• after 25 seconds,

• or 5 seconds after all openeddoors are closed,

• or as soon as the ignition isswitched on or the vehicle islocked.

Lights

50

Headlight levelling control

The level of the headlight beamscan be adjusted according to thevehicle load.

Without headlight levelling

With headlight levelling

Recommended headlight levelling control positions

Load

Persons Load in Control positions

Front seatsRear seats

Load inluggage

compartment

Control positions

1-2 – – 0

1-2 3 – 1

1-2 3 max.1 1.5

1 – max.1 2

1 Data can be found in the section Vehicle weights from page 175 onwards.Higher control positions (+1) may be necessary when towing a trailer.

Lights

51

Multifunction lever

The following functions will operateonly with the ignition switched on.

Direction indicator

• Lane change indicatorsfunction

If the lever is tapped up or down,the direction indicators will flashthree times.

To activate/deactivate this feature,see section Settings menu, page 31onwards.

• Hazards on heavy braking

If the brakes are applied abruptly(e. g. in case of an emergencybraking), the hazard lights willautomatically flash for a minimumof three times.

For further information, see sectionHazards on heavy braking

feature, page 100.

Lights

52

Direction indicator light

A sudden increase in the rate offlashing warns of a failed indicatorbulb.

In addition, on vehicles with aMessage Centre, one of these orboth messages will appear in thedisplay and the display warninglight illuminates amber.

See also section Warning/

information messages, page 26onwards.

If your vehicle has been equippedwith factory fitted or original Fordtowing equipment, the indicatorlight also warns of failure of theindicator bulbs on the trailer.

Main/dipped beam

The main beam only operates withthe headlights switched on.

Pull the lever towards the steeringwheel to toggle between main anddipped beam.

Headlight flasher

Pull the lever slightly towards thesteering wheel.

Main beam indicator light

Illuminates when the headlights areon main beam or when theheadlight flasher is used.

Lights

53

INTERIOR LIGHTS

Off

Door contact

On

On some models, with the switch inthe position, the interior lightswill stay on for a while after thedoors are shut. They go offimmediately after the ignition isturned on.

When parking your vehicle with thedoors open for a long period oftime, the interior lights and theluggage compartment light areswitched off automatically after10 minutes. If the interior lights areleft in the position, they will beswitched off after 30 minutes.

To switch the lights back on, switchon the ignition (position II) for ashort time, open a door or press the

button of the radio frequencyremote control.

Reading lights

Reading lights(depending on model variant)

On

Off

Driver controls

54

STEERING WHEELADJUSTMENT

Never adjust the steeringwheel when the vehicle is

moving.

Release the locking lever to adjustthe height of the steering wheel.

Return the lever to its originalposition to secure the wheel.

For further details on sitting in thecorrect position, refer to sectionSeats, page 77.

HORN

The horn can also be operatedwhen the ignition is off.

Driver controls

55

SCREEN WIPER/WASHERCONTROLS

The following functions will operateonly with the ignition switched on.

Front screen

Lever positions:

Single wipe

Intermittent wiping orAutowipers(depending on model variant)

Normal wiping

High speed wiping

To set the intermittent wipeinterval:

Select wipe interval with rotaryswitch:

1 = Short time interval6 = Extended time interval

Autowipers(depending on model variant)

When Autowipers is selected(position ), the wipers will cycleonce regardless of whether thefront screen is wet or dry.

Thereafter, or when the ignition isswitched on with the wiper leveralready in position , the wiperswill not cycle until water isdetected on the front screen.

The rain sensor will continuouslymeasure the amount of water onthe front screen and adjust thespeed of the front wipersautomatically (single wipe,intermittent, normal or high speedwiping).

Driver controls

56

The sensitivity of the rain sensor isset using the rotary control:

1 = High sensitivity: The wipers willwipe even if only a small amount ofwater is detected on the frontscreen.

6 = Low sensitivity: The wipers willonly wipe when a larger amount ofwater is detected on the frontscreen.

Note: The Autowipers feature isintended for use during wetweather conditions only and is verysensitive to anything which touchesthe front screen near to the rainsensor. Objects such as dirt, mist orflies hitting the screen in thislocation may cause the wipers towipe even though the screen ismostly dry.

Note: The Autowipers functionshould not be selected when it issnowing or foggy, or when the roadshave been salted. In these weatherconditions, select position , or

, if necessary.

In icy conditions, make surethat it has been fully

defrosted before selectingautowipers.

Switch off the Autowipersbefore entering a car wash.

Replace the wiper blades assoon as they begin to leave

bands of water and smears orwhen they do not completelyremove water from the frontscreen. If the blades are notreplaced, the rain sensor willcontinue to detect water on thescreen. This will result in thewipers continuing to operatealthough the majority of thescreen is dry.

On vehicles with a Message Centre,if this message appears in thedisplay and the display warninglight illuminates amber, it indicatesa malfunction.

Switch the wipers on (position , or , as necessary) and off

manually and have the systemchecked by an expert.

Driver controls

57

Rear screen

Wiping

Pull the lever towards the steeringwheel. The wiper delay isautomatically set to match the frontwiper setting.

Reverse gear wipe

If only the front wipers areactivated, the rear screen wiper willbe activated automatically when thereverse gear is selected. When thefront screen wiper is switched off,the rear screen wiper will not workunless it is switched on manually.

Washer

While the button at the end of thelever is pressed or the lever ispulled towards the steering wheelthe washer will work in conjunctionwith the wipers.

Once the wash/wipe cycle iscompleted, the front wipers willpause and then perform one morewipe to clear the screen.

Do not operate the washerfor more than 10 seconds at

a time, and never when thereservoir is empty.

Driver controls

58

AUDIO REMOTE CONTROL

Select radio, CD or cassette modeon the radio.

The following functions can beoperated with the remote control:

Volume

Volume up: Pull the VOL+ switchtowards the steering wheel.

Volume down: Pull the VOL- switchtowards the steering wheel.

Seek

Move the SEEK switch towards thesteering wheel or the instrumentpanel:

• In radio mode, this will locatethe next radio station up or downthe frequency band.

• In CD mode, it will select thenext or the previous track.

Mode

Briefly press the � button on theside:

• In radio mode, this will locatethe next pre-set radio station.

• In CD mode, it will select thenext CD if a CD changer is fitted.

• In all modes to abort a trafficmessage during broadcasting.

Press and hold the � button on theside:

• In radio mode to change thewaveband.

For further details, please refer tothe separate manual.

Driver controls

59

MIRRORS

Interior rear-view mirror

To reduce glare when driving atnight dip the mirror by adjustingthe lever.

Convex outside rear-viewmirrors

The rearward field of vision isincreased to minimise blind spots atthe rear corners of the vehicle.

Objects seen in thesemirrors will look smaller

and appear further away thanthey actually are. Be careful notto overestimate the distance ofthe objects seen in the mirrors.

Manually adjustable outsiderear-view mirrors

Both outside rear-view mirrors areadjustable from inside the vehicle.

Manually folding outsiderear-view mirrors

If required, in narrow spaces forexample, your outside rear-viewmirror can be folded back manually.To return the door mirror to itsoriginal position, push it into themirror support until engaged.

Driver controls

60

Electrically operated and heatedoutside rear-view mirrors

The outside rear-view mirrors areheated when the heated rear screenis switched on.

Left-hand mirror

Off

Right-hand mirror

Mirror tilting positions

Up

Right

Down

Left

Electrically operated foldingfunction(depending on model variant)

In the centre position push thecontrol unit down. To return thedoor mirror to its original position,push the control unit down again.

If the mirrors are folded more than10 times in 60 seconds they willde-activate for 3 minutes to preventoverheating. After 3 minutes themirrors will return to normaloperation.

Automatic folding function(depending on model variant)

The outside rear-view mirrors arefolded back automatically:

• if the mirrors are not folded backusing the control unit and

• if the vehicle is locked using theradio frequency remote control.

After the mirrors were folded backautomatically, they unfold againautomatically:

• if the vehicle is unlocked in anyway, or

• if the ignition is switched on(position II).

Driver controls

61

FRONT POWER WINDOWS

Before operating powerwindows you should verify

they are free of obstructions andensure that children and/or petsare not in the proximity ofwindow openings. Failure to do socould result in serious personalinjury. It is the primaryresponsibility of the supervisingadults never to leave a childunattended in a vehicle and neverto leave the keys in anunattended vehicle.

Switch on the ignition to operatethe power windows.

Note: When the switches areoperated constantly, the system willautomatically switch off for a shortperiod of time to preventoverheating.

To open/close the windows

The front windows can be operatedwith switches located on the doortrim of the driver’s door. Thewindows open/close when theswitch is pressed. The frontpassenger’s window can also beoperated with a switch on the doortrim of the passenger’s door.

The windows open/close only whena button is pressed.

Press : to open.

Press : to close.

To open the driver’s windowautomatically

Briefly press button to thesecond action point to open. Pressagain to stop the window.

Driver controls

62

OTHER CONTROLS

Sunroof

Always push the handle back intoits recess after use.

To open the sunroof

Pull out the handle and turn itanticlockwise to open the sunroof.

With the first two revolutions therear of the sunroof will be lifted up.

If you turn the handle further, theraised sunroof will open from thefront and slide back over the roof.

To close the sunroof

Pull out the handle and turn itclockwise to close the sunroof.

Sun visors

The sun visors can be released fromthe retention clips and swivelledtowards the side window.

The mirror cover can be folded up.

Driver controls

63

Cigar lighter/power point

Never hold the lighter in, asthis will result in damage.

Always remove the lighter as aprecaution when children are leftalone in the vehicle.

To use the lighter press it in andwait until it pops out automatically.The lighter will also operate whenthe ignition is switched off.

The lighter socket can also be usedto power 12 volt appliances havinga maximum current rating of10 amperes. However, if the engineis not running, this will cause thebattery to discharge.

When connecting appliances, useonly specified connectors from theFord Accessory range or connectorssuitable for use with SAE standardsockets.

Front ashtray

Pull the cover to open.

To empty, gently pull up on theopen lid and extract the completeashtray.

Locks (security)

64

KEYS

In case of loss, replacement keysare available from dealers by statingthe key number shown on the tagprovided with the original keys.

For further information, refer tosection Engine immobilisation

system, page 73.

To ensure a trouble-freedata exchange between the

vehicle and key, do not shield thekeys with any metal objects.

Key with radio frequency remotecontrol

The transmitter is integrated intothe key.

General notes on the radiofrequency remote control

For type approval of your remotecontrol, refer to the table onpage 181.

The vehicle or luggagecompartment will be

unlocked if the or buttonsare pressed unintentionally,without the remote control beingdirected towards the vehicle (e.g.in your pocket).

The range between transmitter andvehicle is environmentallyinfluenced and varies greatly.

Locks (security)

65

The radio frequency usedby the remote control can

also be used by other shortdistance radio transmissions (e.g.amateur radios, medicalequipment, wireless headphones,remote controls, alarm systemsetc.). If the remote controlfrequencies are jammed, you willnot be able to use any remotefunctions to lock or unlock thevehicle or set the alarm. However,you can lock/unlock with the key.

LOCKS

From outside

All doors can be locked andunlocked from the outside with thekey on a front door.

Note: Only vehicles without remotecontrol are equipped with a lockcylinder in the passenger’s door.

From inside

When inside the vehicle, all doorscan be locked by depressing thedoor handle and unlocked bypulling the door handle.

Locks (security)

66

Rear door childproof safetylocks

When the childproof safetylock is activated, the door

can only be opened from outside.

Turn the key in the rear doorsrearward to activate the lock. Todeactivate the lock, turn the keyforward.

Luggage compartment

Opening the tailgate

The luggage compartment light willcome on automatically. If theluggage compartment remains openwith the ignition switched off, thelight will be switched offautomatically after 10 minutes.

1. By pressing the Remote luggagecompartment release on theinstrument panel.

Vehicle speed must be below7 km/h and the vehicle must beunlocked.

2. Using the key.

To unlock/open, turn the keyclockwise.

3. Using the radio frequencyremote control. See also section To

unlock the tailgate, page 69.

Locks (security)

67

Closing the tailgate

A recessed grip is incorporatedinside the tailgate to facilitateclosing.

Close the tailgate properlyto prevent it opening while

you are driving.

Doors open warning

The doors open warning lightilluminates when the ignition isswitched on and remains on if anydoor, the luggage compartment orthe bonnet is not closed properly.

On vehicles with a Message Centre,instead of the doors open warninglight one or more of these messageswill appear in the display and thedisplay warning light illuminatesamber.



Locks (security)

68

CENTRAL DOOR LOCKINGSYSTEM

The central door locking systemcan be activated from the driver’s orfront passenger’s door.

It operates only when both frontdoors are closed.

It is activated from the outside withthe key or the remote control andfrom inside by pressing the doorhandle on the driver’s door or(vehicles without remote control)the front passenger’s door.

When the system is activated, thelocking procedure is heard followeddirectly by a secondary noise. Thissecondary noise is a system checkand does not indicate amalfunction.

To lock the rear doors and (vehicleswith remote control) the frontpassenger’s door individually, pressthe door handle and close the doorwhen leaving the vehicle.

The luggage compartment remainslocked when the system isdeactivated.

Central locking with doublelocking system

Double locking is an additional theftprotection feature which preventsthe vehicle’s doors being openedfrom inside the vehicle.

Double locking should notbe activated when persons

are inside the vehicle.

Double locking is possible only ifthe front doors are closed.

Locks (security)

69

Unlocking the vehicle

With the key: Turn the key in thedriver’s or front passenger’s door toposition .

With the remote control: Press the button once.

• The direction indicators will flashonce to confirm that all doors areunlocked and the double lockingand the anti-theft alarm system (ifequipped) are deactivated.

Note: After 22 days the remotelocking system will shut down tosave the battery. It will bereactivated when the doors areunlocked with the key.

Automatic relocking

Note: To prevent the vehicle beingleft unlocked inadvertently, centrallocking and the anti-theft alarmsystem will be reactivatedautomatically 45 seconds after the

button is pressed if the followingoccurs during this period:

• No door is opened.

• The luggage compartment is notoppened.

• The ignition is not switched on.

If a failure occurs in thevehicle’s electrical system,

the front doors and the tailgatecan still be individually unlockedwith a key.

To unlock the tailgate

Press the button twice within3 seconds.

Locks (security)

70

Reprogramming the unlockingfunction

You can change the unlockingfunction so that pressing the button once deactivates the doublelocking and the anti-theft alarmsystem and unlocks only thedriver’s door. Pressing the buttonagain within 3 seconds also unlocksthe passenger’s doors.

To re-programme the function, seesection Settings menu, page 31onwards, if a message centre isequipped.

In order to re-programme thefunction, press and hold the and

buttons simultaneously for atleast four seconds with the ignitionswitched off. The directionindicators will flash twice toindicate that the unlocking functionhas been successfullyre-programmed.

Pressing and holding both buttonsagain simultaneously for at least4 seconds will change the functionback.

Locking the vehicle

To activate central locking and armthe anti-theft alarm system (ifequipped):

With the key: Turn the key in thedriver’s or front passenger’s door toposition .

With the remote control: Press the button once.

• On vehicles without doublelocking, the direction indicators willflash twice as confirmation.

Locks (security)

71

To activate double locking and armthe anti-theft alarm system (ifequipped):

Left-hand door.

Right-hand door.

With the key: Turn the key in thedriver’s or front passenger’s door toposition and then to position within two seconds.

With the remote control: Press the button twice within 3 seconds.

• The direction indicators will flashtwice as confirmation.

Programming additional radiofrequency remote controls

A maximum of four radio frequencyremote controls can beprogrammed (including the onesdelivered with the vehicle).

1. To programme new radiofrequency remote controls turn theignition key from position 0 toposition II four times within sixseconds.

2. Switch off the ignition. A tonesounds to indicate that it is nowpossible to programme new radiofrequency remote controls for10 seconds.

Locks (security)

72

3. Press any button on a new radiofrequency remote control. A tonewill sound as confirmation. Repeatthis last step for all your radiofrequency remote controls,including your original ones, within10 seconds.

4. Switch the ignition back on orwait for ten seconds withoutprogramming another remotecontrol to end the programming.Only the radio frequency remotecontrols which you have justprogrammed are now able to lockand unlock the vehicle.

Replacing the remote controlbattery

If the range of the transmitter inthe key decreases gradually, thebattery (type 3V CR 2032) shouldbe replaced.




• Carefully separate the transmitterunit from the key using a flat object(e.g. a screwdriver) in the recess onthe back.

• Open the transmitter unit byseparating the retaining clips on thesides with the flat object.

• Carefully prise out the batterywith the flat object. Fit the newbattery between the contacts withthe (+) sign facing upwards.Reassemble the transmitter unit inreverse order.

Locks (security)

73

ENGINE IMMOBILISATIONSYSTEM

The engine immobilisation systemis a theft protection feature whichprevents the engine from beingstarted with an incorrectly codedkey.

Coded keys

Your vehicle is supplied with codedkeys.

Replacement keys must be recodedtogether with your other keys.

Automatic arming

The system is armed after switchingoff the ignition. The Engineimmobilisation system indicatorlight in the instrument cluster willflash.

Automatic disarming

Switching on the ignition disarmsthe system if the correct code isrecognised. The indicator light inthe instrument cluster illuminatesfor approximately 3 seconds andthen extinguishes.

If the indicator light staysilluminated or begins to flashrapidly, the system remains armedand the engine does not start.Remove the key and try again.

If the engine does not start, asystem malfunction has occurred.Have the system checked by anexpert immediately.

Locks (security)

74

Key coding

A maximum of eight keys(including the ones delivered withthe vehicle) can be coded using twoother keys previously coded foryour vehicle.

Complete each of the followingsteps within 10 seconds.

1. Insert the first key in theignition switch and turn to position II.

2. Turn the key back to position 0and remove from the ignitionswitch.

3. Insert the second key in theignition switch and turn toposition II.

4. Turn the second key back toposition 0 and remove from theignition switch – the key codingmode is now activated.

5. If an uncoded key is nowinserted in the ignition switch andturned to position II within20 seconds, this key is coded to thesystem.

6. After the coding process iscompleted remove the key from theignition switch.

If coding is not completed correctly,the indicator light flashes after theignition is switched on with thenewly coded key and the enginewill not start.

If a key is lost, it isimperative that the

remaining keys are erased andrecoded. Consult an expert if younow have only one valid key.

Locks (security)

75

Coding erasure

With two keys coded for yourvehicle you can make all the othercoded keys unusable, e.g. after loss.

Complete each of the followingsteps within 10 seconds.

Carry out the first four steps underKey coding, then continue asfollows:

5. Insert the second key in theignition switch again and turn toposition II.

6. Remove the key from theignition switch.

7. Insert the first key in theignition switch, turn to position IIand hold. The indicator light flashesfor 5 seconds.

8. If the ignition is switched offduring these 5 seconds, the erasureprocess is terminated and no key iserased.

9. If the erasure process iscompleted, all the other keys, apartfrom the two used for erasure, canno longer be used unless recoded.

Additional keys can now be coded.

Locks (security)

76

ANTI-THEFT ALARM SYSTEM

The system is armed as soon as thevehicle is locked and acts as adeterrent to unauthorised personswho attempt to open the doors,bonnet or luggage compartment.

Automatic arming delay

Up to 20 seconds after arming theanti-theft alarm system, it is stillpossible to open the vehicle againwithout triggering the alarm. Afterthat, the anti-theft alarm systemwill monitor all doors, the bonnetand the tailgate, provided that theyare closed. If a door, the bonnet orthe tailgate is closed later, thesystem will monitor it after20 seconds.

Alarm

The alarm sounds for 30 seconds ifan unauthorised person opens adoor, the luggage compartment orthe bonnet. The hazard flasherlights will flash for 5 minutes.

Any attempt to start the enginewithout a valid key sounds thealarm again.

To switch off

The anti-theft alarm system can bedisarmed at any time – even whenthe alarm is sounding – byunlocking either of the front doorswith the key or with the remotecontrol.

The anti-theft alarm system on thetailgate is disarmed when theluggage compartment is unlockedwith a key.

After closure, the alarm is onceagain armed.

Seating and safety restraints

77

SEATS

Sitting in the correct position

• Sit in an upright position with thebase of your spine as far back aspossible and with the seatbackreclined no more than 30 degrees.

• Adjust the head restraints so thatthe top is level with the top of yourhead.

• Do not move the front seat tooclose to the instrument panel. Thedriver should hold the steeringwheel in the ‘10 to 2 o’ clock’position with arms slightly bent.The legs should also be slightly bentso that the pedals can be pressedfully to the floor.

• The seat belt should cross thecentre of the shoulder; the lap strapshould fit tightly across the hips,not the stomach.

Do not use any accessoryseat covers that are not

specifically designed for seatswith side airbags. These seatcovers must be fitted by properlytrained technicians.

Do not adjust the seatswhile the vehicle is moving.

Moving the seats forwards orbackwards

Pull the lever. Rock the seat toengage the catch.


78

Adjusting the height of thedriver’s seat

Each pull or press on the lever willraise or lower the height by a smallamount.

Adjusting the angle of theseatback

When the seats are slid fullyforward the seatbacks can be fullyreclined.

Armrest

To adjust the driver’s armrest to acomfortable height:

• Pull the armrest all the way back,past vertical .

• Push the armrest all the waydown .

• Slowly raise the armrest to thedesired position .

Note: If the armrest is too high,repeat the procedure.


79

Fold flat front passenger seat

To fold the front passenger seat flat,pull the unlocking lever and fold theseatback forwards. Turn thehandwheel at the side of the seatuntil the seatback reaches thehorizontal position.

Pull the unlocking lever to returnthe seatback to the uprightposition.

When returning the seatback to theupright position, ensure that itlocks with a distinct click.

The front passenger seatmust be in the upright

position when driving if the seatdirectly behind it is occupied.

Only children up to 18 kg maytravel on the rear seat when thepassenger seat is folded flat.

Do not place objects on thetable surface when driving

as these could become projectilesin the event of an accident orheavy braking.

Heated front seats

Driver’s seat

Front passenger’s seat


80

The red mark on the side of theswitch indicates that the heatedseat is on.

The maximum temperature isreached after five or six minutes. Itis regulated thermostatically.

When selected the heating willoperate when the ignition switch isin position II.

Heating with the engine offwill drain the battery.

Head restraints

Front head restraints

To adjust the height, pull the headrestraint up or press the lockingbutton and push the head restraintdown.

Make sure that the head restraintengages properly when in position.

To remove, press the locking buttonand pull out the head restraint.

To replace, push the head restraintback into position.

Rear head restraints

To raise, pull the head restraint upuntil it engages properly.

To lower, press the locking buttonand push the head restraint down.

Always have the rear headrestraint raised when the

rear seat is occupied by apassenger or a child restraint.


81

Folding the rear seatbackforwards

Lower the rear head restraints.

Pull the unlocking handle on therear seatback and fold the rearseatback forwards.

Returning the seatback to itsupright position

The seatback must engage in thelatches.

Note: When the red marking in theunlocking mechanism is visible, theseatback is not fully engaged.Release the seatback and repeat theprocedure until the red marking isno longer visible.

Note: If the seat belt integratedinto the centre seatback does notfunction properly, check theunlocking mechanism.

The seat belts must be forward ofthe seatback.


82

Folding the seat cushion andseatback forwards

Slide the front seat forwards.

Fold the seat cushion forwards .

Lower the head restraints of therear seats and fold the seatbackforwards as described in thesection Folding the rear seatback

forwards, page 81.

Press the rear of the seatback downto create a level surface .

When returning the seats to theiroriginal positions, make sure theseat belts will function properly andare positioned in front of theseatback.

SEAT BELTS

• Use seat belts at all times.

• Never use a seat belt for morethan one person.

• Avoid wearing thick clothing.

• The seat belts should fit tightlyaround the body.

Fastening the seat belts

Pull the belt out steadily. It maylock if pulled sharply or if thevehicle is on a slope.

Insert the tongue into thebuckle until a distinct click

is heard, otherwise the seat beltwill not be locked correctly.


83

To release the belt, press the redbutton on the buckle and let thebelt rewind completely andsmoothly.

Make sure that each seat belt usesthe correct buckle.

If your vehicle is equipped with acentre static belt:

To loosen, turn the tongue at rightangles to the webbing and pull it.When fastening, ensure the tongueengages in the buckle with apositive click. To tighten, pull theloose end through the tongueensuring the belt fits snugly acrossthe hips in a low position.

Adjusting the height of the frontseat belts

Press the locking control on theheight adjuster and move the pivotso that the belt rests across thecentre of the shoulder.


84

Pregnant women

Pregnant women must weara correctly positioned seat

belt; it is safer for mother andunborn child.

The lap strap should be fittedcomfortably across the hips, lowbeneath the pregnant abdomen.The diagonal part of the seat beltshould be placed between thebreasts, and worn above and to theside of the pregnant abdomen.

Always wear seat belts withoutslack or twists. For optimumprotection, the seat belts should fittightly around the body. Do notrecline the front seats excessively,as the belts provide maximumprotection when the seats are in thenear upright position.

Never wear just the lapstrap of a lap/shoulder

diagonal seat belt and never sit onthe lap strap using just theshoulder strap. Both of theseactions are extremely dangerousand may increase your risk ofserious injury.


85

Seat belt pretensioner

The belt pretensioners mustnot be removed. If the

pretensioners deployed during anaccident, they must be replaced.Have the pretensioners servicedand disposed of by speciallytrained personnel only.

Driver’s seat

Front passenger’s seat

The restraint system, with beltpretensioner in the front seats,helps to reduce the risk of seriousinjury in a major frontal impact.During a serious crash the seatbelts are pretensioned to helpreduce slack in the belt. The safetybelt pretensioner is a device whichremoves excess webbing from thesafety belt system. When the safetybelt pretensioner deploys, webbingfrom the lap and shoulder belt istightened.

The belt pretensioner is nottriggered in any side, rear or minorfrontal collisions. For further detailsrefer to section Airbag, page 87onwards.


86

Care of seat belts

Periodically check the belts fordamage or fraying.

Do not attempt to repair orlubricate retractor or buckle

mechanisms or to modify thebelts in any way.

Belts subjected to strain - as aresult of an accident - should berenewed and the anchorageschecked by an expert.

For information about cleaning theseat belts, please refer to sectionCleaning seat belts, page 161.


87

AIRBAG

The system

The airbag system comprises thefollowing:

• inflatable nylon bags (airbags)with gas generators

• side airbags

• curtain airbags

• seat belt pretensioners

• a number of crash sensors

• a warning light in the instrumentpanel

• an airbag deactivation switch (ifequipped)

• an airbag deactivation light in theinstrument panel (if equipped)

• an electronic control anddiagnostic unit

Note: A loud bang will be heardwhen an airbag deploys and it isnormal to see a cloud of harmlesspowdery residue.


88

Front airbags

The seat and back must be setcorrectly for the airbags to beoptimally effective. Refer to sectionSitting in the correct position,page 77.

This is the ideal seating position forthe driver and front passenger andhelps reduce the risk of injury fromsitting too close to an inflatingairbag.

Always wear the seat beltand keep sufficient distance

between the driver and thesteering wheel. Only when theseat belt is used properly, can ithold the body in a position whichallows the airbag to achieve itsoptimum effect. There is a risk ofinjury when the airbag deploys.

Do not modify the front ofthe vehicle in any way as

this can adversely affect airbagdeployment.

The front airbags activate duringmajor collisions which are eitherfrontal or up to 30 degrees fromthe left or the right. The airbagsinflate within a few thousandths ofa second. They will deflate oncontact with the front occupantsthus cushioning forward bodymovement.


89

During minor collisions as wellas overturns and rear or sidecollisions, the front airbagsystem will not be activated.

Always keep the areas infront of the airbags free.

Never affix anything to or overthese areas.

These areas should only be wipedwith a damp cloth, never with a wetcloth.

Repairs to the steeringwheel, steering column and

airbag system should be carriedout by properly trainedtechnicians.

Side airbags

A label on the seatback indicatesthat side airbags are fitted.

The side airbags are fitted on theside of the seatbacks of the frontseats. In case of a severe lateralcollision, the airbag on the sideaffected by the collision will beinflated.

The airbag will inflate between thedoor panel and occupant. Once theoccupant’s body contacts theairbag, the propellant escapes,thereby cushioning the impact.

The side airbags are notactivated upon minor lateralcollisions nor upon front orrear impacts.


90

Front and rear curtain airbags

Moulded badges in the headliningover the side windows indicate thatcurtain airbags are fitted.

The curtain airbags are fitted overthe front and rear side windowsinside the roof lining.

In case of a severe lateral collision,the airbag on the side affected bythe collision will be inflated.

The curtain airbags are notactivated upon minor lateralcollisions nor upon front orrear impacts.

Repairs to either of thefront seat covers, the

sensors attached to the seats aswell as to the roof lining shouldonly be carried out by properlytrained technicians. Injuries mayresult if the side airbags aretriggered inadvertently.

Do not block, obstruct or coverthe airbag because it may preventproper deployment.

Do not poke any sharp objectsinto the areas where airbags arefitted. This could damage theairbags.

Do not use any accessory seatcovers that are not specificallydesigned for seats with sideairbags. These seat covers mustbe fitted by properly trainedtechnicians.


91

Airbag/seat belt pretensionerwarning light

When the ignition switch is turnedto position II, the warning light onthe instrument panel illuminatesfor approximately 3 secondsto indicate that the system isfunctional.

If the warning light does notilluminate, if it stays on orilluminates intermittently orcontinuously while driving, it meansthere is a malfunction. Have thesystem checked by an expert.

Passenger airbag deactivation

If individual circumstances requireyou to fit a child seat/restraint on aseat protected by an operationalairbag in front of it, your vehicle isequipped to allow fitting of apassenger airbag deactivationswitch operated by the ignition key.

Your Ford Dealer will be able to fitit.

The key switch will be fitted on theend of the instrument panel with anairbag deactivation light in thecentre of the instrument panel.

To use a rear facing child restraintin the front, make sure that the keyswitch is turned to the OFFposition .


92

To avoid the risk of death orserious injury, NEVER use

a rearward facing child restraintin the front, unless the airbag isOFF.

When the ignition is switched on(position II), check that the airbagdeactivation light is illuminated.

If the instrument cluster airbag/seatbelt pretensioner warning lightilluminates intermittently, it meansthere is a malfunction. Remove thechild restraint from the front.

Have the system checked by anexpert for your own safety. Refer also to section Airbag/seat

belt pretensioner warning light,page 91.

ON

After removing the child restraintfrom the front, make sure that thekey switch is turned to the ONposition .

To ensure the adultrestraint system performs

as intended, make sure the airbagis ON.


93

CHILD RESTRAINTS

Together with the adult seat belt,these restraints help providemaximum security for children.

Children of height 150 cm or underor 12 years or under should besecured in special restraints forchildren, such as baby seats, childsafety seats or booster seats andcushions in the rear seat. Size andage limits for mandatory use ofchild restraints vary betweenindividual countries.

Such equipment must be suitableand government approved(depending on country).

Extreme Hazard! Do not usea rearward facing child

restraint on a seat protected byan operational airbag in front ofit!

There is a risk of death or seriousinjury when the airbag deploys.

Whenever installing a child seat/restraint, always read and followthe manufacturer’s instructions.

There is a risk of death orserious injury when the

manufacturer’s instructions arenot followed properly or when thechild restraint is modified in anyway.

Note: If your vehicle is equippedwith the airbag deactivationfeature, please see the sectionPassenger airbag deactivation,page 91.

Do not hold a child on yourlap when the vehicle is

moving.

A choice of ECE approved childrestraints is available at your FordDealer. Please ask for therecommended child seats.


94

Placement of child restraints

If your Ford vehicle isequipped with a front

passenger airbag, it isrecommended that children ofheight 150 cm or under or aged12 years and under should only beproperly restrained in the rearseat. Rearward facing childrestraints must NEVER be usedin the front passenger seatprotected by an OPERATIONALfront passenger airbag.

The following table advises on thesuitability of child restraint fitmentlocations.

Child restraint positions

Mass group categories

0 0+ I II III

Seatingpositions

Up to 10 kg(about 0-9months)

Up to 13 kg(about 0-18

months)

9 to 18 kg(about 9months-4 years)

15 to 25 kg(about31/2-

6 years)

22 to 36 kg(about 6-12

years)

Baby safety seatChild

safety seatBooster seat/cushion

Front passenger

airbag ONX X U1 U1 U1

Front passenger

airbag OFFU U U U U

Rear seats U U U U URear seats U U U U U

X = Seat position not suitable forchildren in this mass/age group.

U = Seat position suitable for�universal" category restraintsapproved for use in this mass/agegroup.

U1 = Seat position suitable for�universal" category restraints butFord recommends that childrenshould be secured in an appropriatechild restraint in the rear seats.

To use a child restraint in the front,make sure that the passengerairbag deactivation key switch isturned to the OFF position (seepage 91 onwards).


95

If completely unavoidablecircumstances call for a

child weighing more than 9 kg totravel in a front seat protected byan operational front airbag,always use a forward facing childrestraint.

Extreme Hazard! Do not usea rearward facing child

restraint on a seat protected byan operational airbag in front ofit!

Always have the headrestraint raised when a

child restraint is being installed oroccupying the seat, provideddoing so does not move the childrestraint away from the vehicleseat.

Child restraints for differentmass groups

The correct restraint to be useddepends on the child’s weight andage:

• Baby safety seat

Babies under 13 kg (approximately18 months) are best protected ifproperly restrained in rearwardfacing baby safety seats(Group 0+) in the rear seat.


96

• Child safety seat

Children weighing between 13 and18 kg (approximately eighteenmonths to four years old) should becarried properly restrained in childsafety seats (Group I) in the rearseat.

• Booster seat/booster cushion

Booster seat

Booster cushion

Children weighing more than 15 kgand under 150 cm should use abooster seat or booster cushion.Ford recommends using boosterseats that combine a boostercushion and a back rest into oneseat for children between 15 kg and25 kg. The raised seating positionensures that the adult seat belt canbe correctly guided over the centreof the shoulder instead of along theneck, the lap belt lying tightlyacross the hips instead of thestomach. Make sure that your childsits in an upright position.


97

Note:

• If the vehicle has been involved inan accident, have the child safetyseat checked by an expert as itmight be damaged.

• When the child seat is not in usebut inside the vehicle, secure itwith the seat belt.

• Do not leave children unattendedin the child safety seat or in thevehicle.

• When installing a childseat/restraint with the seat belt,always ensure belts fit without slackor twists.

You should never use abooster seat or cushion with

only a lap belt.

Never put the shoulder belt undera child’s arm or behind the back.

Never use pillows, books, ortowels to boost a child.

Driving

98

BRAKES

Dual circuit braking system

Your vehicle is equipped with adiagonally split dual circuit brakingsystem. If one of the brake circuitsfails, the other remains operative.

If a brake circuit fails, youwill at first experience a

softer feel to the brake pedal. Youwill then need to exert a greaterforce on the brake pedal, andmake allowance for increasedstopping distances. Have thebraking system checked by anexpert before continuing yourjourney.

Disc brakes

Wet brake discs result in reducedbraking efficiency.

After leaving a carwash or drivingthe vehicle through water, dab thebrake pedal while driving to removethe film of water.

Brake system warning

The Brake system warning lightremains illuminated when thehandbrake is engaged.

If it illuminates afterreleasing the handbrake or

when driving, have the brakingsystem checked by an expertimmediately.

In addition, on vehicles with aMessage Centre, this message willappear in the display and thedisplay warning light illuminatesred.



Driving

99

Anti-lock Braking System (ABS)

The ABS operates only when thewheels are about to lock. Itsoperation is indicated by a pulsingof the brake pedal and full steeringcontrol is retained. Do not releasethe pedal whilst braking.

Although the ABS ensuresoptimum braking efficiency,

stopping distances can varygreatly depending on the roadsurface and conditions. Use of theABS cannot eliminate the dangersinherent in driving too close tothe vehicle in front of you,aquaplaning, excessive corneringspeed or poor road surfaces.

ABS warning light

If the ABS warning light illuminateswhen driving, it indicates amalfunction. Have this checked byan expert.

Normal braking (without ABS) willbe maintained.

Brake system and ABS warninglights

If both warning lights illuminate atthe same time when driving, stopthe vehicle as soon as it is safe todo so. Have the braking systemchecked by an expert beforecontinuing your journey.

Reduce vehicle speedgradually. Use the brakes

with great care. Do not step onthe brake pedal abruptly.

In addition, on vehicles with aMessage Centre, the warningmessage will appear in the displayand the display warning lightilluminates red.

See also sections Brake system

warning, page 98, and Warning/


Driving

100

Emergency Brake Assist(depending on model variant)

The Emergency Brake Assist is ableto detect an emergency brakingsituation by measuring the rate atwhich the brake pedal is applied. Itautomatically provides maximumbraking efficiency as long as thepedal is applied. This can reducestopping distances in criticalsituations.

The Emergency BrakeAssist is an additional

system which is not intended torelieve the driver of hisresponsibility for exercising duecare and attention when driving.

Hazards on heavy brakingfeature(depending on country)

At a vehicle speed of 96 km/h ormore and if the brakes are appliedabruptly (e. g. in case of anemergency braking), the hazardlights will automatically flash for aminimum of three times.

When the vehicle moves off again orif the hazard flasher switch ispressed, the hazard lights areswitched off. The function isavailable again, when the vehicle’sspeed reaches 96 km/h or more.

To activate/deactivate this feature,see section Settings menu, page 31onwards.

Handbrake

• Press the foot brake pedal firmly.

• Pull the handbrake lever upsmartly to its fullest extent.

• Do not press the release buttonwhile pulling the lever up.

• If your vehicle is parked on a hilland facing uphill, select first gearand turn the steering wheel awayfrom the kerb.

• If your vehicle is parked on a hilland facing downhill, select reversegear and turn the steering wheeltowards the kerb.

Vehicles with an automatictransmission should always

be left with the selector lever inposition P.

To release the handbrake, press thebrake pedal firmly, pull the lever upslightly, depress the release buttonand push the lever down.

Driving

101

ELECTRONIC STABILITYPROGRAM (ESP)

Drivers should never takeunnecessary risks even

though the ESP system offersinherently safer driving potential.

Principle of operation

with ESP

without ESP

The ESP system provides anenhanced traction control functionby reducing wheel spin at thedriven wheels when accelerating.This improves the ability to pullaway on slippery roads or loosesurfaces.

The system also supports stabilityby counteracting the tendency ofthe vehicle to swerve away from theintended path. This is performed bybraking individual wheels and/orreducing engine torque as needed.

When the ignition is switched on(position II), the ESP indicator lightilluminates briefly to confirm thatthe system is operational.

Whilst driving, the light flashesduring periods of activation.

When the ESP indicatorlight is flashing the driver

should take care and adapt theirdriving to the current conditions.

Note: If the indicator light does notilluminate when the ignition isswitched on or if it staysilluminated whilst driving, itindicates a malfunction. Have thesystem checked by an expert.

Driving

102

Switching off the ESP

The system can be switched offmanually by pressing and holdingthe ESP switch for at least onesecond. When the system isswitched off, the ESP indicator lightin the instrument cluster willilluminate. The system can bere-enabled by pressing and holdingthe switch again.

Each time the ignition is switchedon, the system is automaticallyselected.

STEERING COLUMN LOCK/IGNITION SWITCH

0 Ignition off.

When the key is removed from theignition switch, the steering columnlock is activated as soon as thesteering wheel is turned.

On vehicles with automatictransmission, the ignition key canbe returned to position 0 andremoved only if the selector lever isin the park position P.

I Steering unlocked. Ignition andall main electrical circuits aredisabled.

The ignition key should not be leftin this position for too long to avoiddischarging the battery.

II Ignition switched on, allelectrical circuits operational.Warning and indicator lightsilluminate. This is the key positionwhen driving and must also beselected when being towed.

III Starter motor activated. Releasethe key as soon as the engine starts.

Never return the key to the0 position when the vehicle

is in motion.

Driving

103

GENERAL POINTS ONSTARTING

The starter will not operate forlonger than 30 seconds during eachstart cycle. Release the ignition keyas soon as the engine has started.

If the engine has not started, returnthe ignition key to position 0 andrepeat the starting procedure.

If the engine does not start,refer to the instructions

regarding the fuel injectionsystem shut-off switch onpage 139.

Engine speed limiter

The engine speed is limitedelectronically to protect the engine.

STARTING THE ENGINE

Vehicles with a petrol engine

Cold/hot engine

• Depress the clutch pedal fully andstart the engine without touchingthe accelerator.

At temperatures below-20 ºC, turn the ignition key

to position II for at least onesecond before starting the engine.This ensures that maximum fuelpressure is established.

• If the engine does not start within15 seconds, wait for a short periodand repeat the procedure.

• If the engine does not start afterthree attempts, wait 10 secondsand follow the Flooded engine

procedure.

• If starting difficulty isexperienced at temperatures below-25 ºC, depress the acceleratorpedal 1/4 to 1/2 of its travel to assiststarting.

Flooded engine

• Depress the clutch pedal fully.

• Slowly depress the acceleratorfully, hold it in this position andstart the engine.

• If the engine does not start repeatthe Cold/hot engine procedure.

Driving

104

Vehicles with a diesel engine

If the vehicle run out of fuel, seesection Diesel low fuel safety

mode, page 124.

Cold/hot engine

• Depress the clutch pedal withouttouching the accelerator.

• Turn the key to position II.

• If the Glow plug indicator lightilluminates, wait until itextinguishes before starting.

• Continue cranking withoutpausing until the engine starts.

• If the engine stalls, repeat the fullstarting procedure.

• At temperatures below -15 ºC itmay be necessary to operate thestarter for up to 30 seconds. Ifthese weather conditions persist, anengine block heater isrecommended.

Switching off the engine

Wait until the engine has reachedidle speed, then switch off.

Never depress the acceleratorpedal.

If the engine is switched off at highspeed, the turbocharger willcontinue running after the engineoil pressure has dropped to zero.This will lead to prematureturbocharger bearing wear.

Driving

105

Vehicles with automatictransmission

The engine can be started only withthe selector lever in position P.If necessary, it can also be startedwith the lever in position N.


After starting the engine, the levercan be moved out of position P onlywhen the foot brake is depressedand the release button ispressed.

See also section Automatic

transmission, page 107 onwards.

Vehicles with Durashift EST

The engine can be started onlywhen the lever position is in N andthe footbrake has been depressed.The display will show N. If thefootbrake is not pressed N willflash.

In addition, this message willappear in the display of theMessage Centre and the displaywarning light illuminates amber.

If the vehicle is parked in gear thebrake pedal should be pressed withthe ignition switched on whilstmoving the lever to neutral. Thiswill release the gear.

Driving

106

If the brake pedal is not pressed thegear will not be released, thedisplay will flash and the vehiclewill not start.


See also section Durashift EST

from page 115 onwards.

MANUAL TRANSMISSION

Do not apply any unduelateral force to the gear

lever when changing from 5th to4th gear as this could lead to theinadvertent selection of 2nd gear.

Engage reverse gear onlywhen the vehicle is

stationary.

To avoid shifting noises whenengaging the reverse gear, waitapproximately three seconds withthe clutch depressed when thevehicle is stationary.

To select the reverse gear, shift thelever into the neutral position andthen press the lever fully to theright against a spring pressure,before pulling rearwards until itengages.

Driving

107

AUTOMATIC TRANSMISSION

The four-speed automatictransmission is electronicallycontrolled.

Selector lever

To disengage from P, make sure theignition key is in position II, depressthe brake pedal and press therelease button on the side of theselector lever grip.

Press the release button to changefrom N to R or P, from D to 2 or 1and from R to P.

Selector lever positions

Apply the handbrake ordepress the footbrake

before selecting a gear. Failure todo so could result in the vehiclepulling away when you haveengaged a gear.

Note: A cold engine runs at ahigher idling speed after starting.This can cause a strong ‘creep’tendency in reverse and forwardgears.

Gear display

On vehicles with a Message Centre,the display in the instrumentcluster shows the gear currentlyengaged (P, R, N, D, 2 or 1).

Driving

108

P = Park

In this position, the transmission islocked.

This position should beselected only when the

vehicle is stationary.

Whenever you leave thevehicle, make sure that the

selector lever is securely latchedin P, always apply the handbrakefully and turn off the ignition.

A warning signal will soundif the drivers door is opened

when position P is not selected.


The battery saver deactivates thisalarm 10 seconds after the key isturned to position 0.

The key can be removed from theignition lock only in position P.

Before the transmission reachesnormal operating temperature, itruns in a special mode. See sectionCold mode on page 112.

R = Reverse

This position should be selectedonly when the vehicle is stationaryand the engine is idling.

N = Neutral

In this position, no power istransmitted to the drive wheels.

In this position, you have todepress the brake pedal or

apply the handbrake to preventthe vehicle from moving.

D = Drive

When stationary, thisposition should only be

selected when the engine isidling.

This is the normal driving position.

When the brake pedal is released,the vehicle will creep. All forwardgears are selected automaticallydepending on driving conditions.

Driving

109

2 = Gear 2

The automatic transmissionremains permanently in 2nd gear.

This position should be selected onsevere downhill gradients.

It can also be used to avoidfrequent shifting between 1st and2nd gears in slow moving traffic orto help when moving off on slipperyor icy surfaces.

For driving on long uphill gradients,see section Uphill mode, page 112.

1 = Gear 1

The automatic transmissionremains permanently in 1st gear.

This position should be selected onextreme downhill gradients.

For driving on long uphill gradients,see section Uphill mode, page 112.

Overdrive

The 4th gear is designed as anoverdrive.

Switching off the overdrive can helpto increase the engine brakingeffect for enhanced control whendriving on downhill gradients or ifthe transmission is frequentlyshifting between 4th and 3rd gear.

With the overdrive switched off, thetransmission will shift only betweengears 1 – 3.

Depress the button located underthe grip at the side of the selectorlever to switch the overdrive off andon. The overdrive can be switchedoff and on while driving.

When the ignition is switched onagain, overdrive is automaticallyswitched on.

Overdrive indicator light

The indicator light in theinstrument cluster illuminates whenthe overdrive is switched off.

Driving

110

Driving with automatictransmission

Moving off

With the engine idling and thebrake pedal depressed, move theselector lever to one of the drivingpositions. Release the brakes. Thevehicle will start to move slowly inthe selected direction. Depress theaccelerator pedal to increase speed.

When stationary, only movethe selector lever to one of

the driving positions when theengine is idling.

• Moving off in sand, mud orsnow

If the driving wheels are stuck, tryto rock the vehicle free by drivingforwards and backwards. To do this,move the selector lever alternatelyto D and R and depress theaccelerator as little as possible.

To increase the effect, move theselector lever to R while the vehicleis still moving forward and viceversa.

To avoid excessive wear on thetransmission when shifting betweenforward and reverse (rocking) keepthe engine speed as low as possible.

Selecting position 2 may assistdriving-off on icy or snowy roadsurfaces.

Manual gear changes

• Moving off

Select position 1, release thehandbrake and depress theaccelerator pedal. Move theselector lever to position 2 and D asthe road speed increases.

• Changing down

If the transmission is in 4th gearand the overdrive is switched offthe transmission will change downto 3rd gear if the vehicle speed isbelow 165 km/h. See also sectionOverdrive, page 109.

If the selector lever is moved fromposition D to position 2 whiledriving, the automatic transmissionwill change down to 2nd gear if thevehicle speed is below 85 km/h andwill then remain in this gear. If theselector lever is moved to position 1while driving, the transmission willchange down to 1st gear if thevehicle speed is below 45 km/h andwill then remain in this gear.

Stopping

Release the accelerator pedal anddepress the footbrake. Leave theselector lever where it is. To moveoff again release the footbrake.

Select position N if stationary forlonger periods of time.

Driving

111

Emergency park positionrelease lever

This enables the selector lever to bemoved out of the park position P inthe event of a discharged battery orelectrical failure.

Remove the cover in the centreconsole next to the selector leverwith a flat-bladed tool.:

With a suitable object push downthe locking lever in the slot beneaththe cover and simultaneously movethe selector lever out of the Pposition.

If position P is selectedagain, this procedure must

be repeated.

Drive modes

Downshift

When activated, this mode providesmaximum vehicle performancewhen overtaking or, in conjunctionwith the Uphill mode, driving upsteep gradients.

With the selector lever in positionD, the transmission will select theappropriate gear according to theposition of the accelerator pedal.

When the accelerator is pressed farenough, a resistance point can befelt. Maximum engine output isachieved when the pedal is heldagainst this resistance point. Thetransmission selects the optimumgear for comfort and acceleration.

The transmission will change to thenext higher gear before the enginespeed approaches its upper limit.

The maximum possible accelerationmay not be achieved. Use theKickdown mode to achievemaximum acceleration.

Driving

112

Kickdown

When activated, this mode providesmaximum possible accelerationwhen overtaking or, in conjunctionwith the Uphill mode, driving upsteep gradients.

With the selector lever in positionD, depress the accelerator pedalfully beyond its resistance pointand hold it down.

The Kickdown mode is activatedand the transmission will select theappropriate gear for maximumpossible acceleration. In somesituations, this gear may already beselected.

With the Kickdown mode activated,the transmission will not shift intothe next higher gear until theengine speed approaches its upperlimit.

Keep the pedal pressed fullybeyond the resistance point to keepthe Kickdown mode activated for aslong as maximum acceleration isrequired.

The transmission will return to itsnormal operating mode as soon asthe accelerator pedal is releasedand returns to any position beforethe resistance point.

Uphill mode

Always use selector lever position Dfor driving on uphill gradients. Theautomatic transmission detectsuphill gradients and automaticallyselects the most appropriate gear.

Avoid using selector lever positions1 and 2 when driving on long uphillgradients as under somecircumstances this can cause thetransmission operating temperatureto rise above normal limits andenter the Hot mode. See sectionHot mode, page 113.

Downhill mode

Supports your braking manoeuvrewhile driving downhill.

When appropriate, the transmissionshifts down from 4th to 3rd gear toincrease engine braking when thebrakes are applied during downhilldriving.

Cold mode

In order to increase thetransmission’s efficiency and reducewear and tear, 4th gear will not beselected until the transmission hasreached normal operatingtemperature.

Driving

113

Hot mode

When high transmissiontemperatures are detected, thismode is activated to help preventdamage to the transmission.

The Transmission/Engine systemsfault warning light may illuminatewhile the Hot mode is activated.

Note: On vehicles without MessageCentre, if this warning lightilluminates, refer also to sectionTransmission/Engine systems

fault warning, page 122.


The warning light and the messageextinguish when the transmissionhas cooled down to normaloperating temperature.

Note: Please follow the instructionsin the table on page 114.

Emergency mode

If a malfunction occurs in thetransmission, this mode may beactivated. This will result in unusualvehicle behaviour.

The Transmission/Engine systemsfault warning light illuminates whilethe Emergency mode is activated.

Note: On vehicles without MessageCentre, if this warning lightilluminates, refer also to sectionTransmission/Engine systems

fault warning, page 122.


Note: Please follow the instructionsin the table on page 114.

Driving

114

What to do if the transmission warning light is on

1 Stop the vehicle as soon as it is safe to do so.

2 Select position P or N and let the engine idle for 10 minutes.

3 Switch off the engine and restart the engine.

Warning light is still on: Warning light is off:

4Switch off the engine.

Have the transmission checked byan expert before continuing yourjourney.

You can continue your journey.Have your vehicle checked by anexpert at the earliest convenienttime.

Driving

115

DURASHIFT EST

The Durashift EST is an automatedfive-speed manual transmission.The clutch and the gear selectionare operated automatically.

Selector lever

Gear selections are made by use ofthe gear selector lever.

Creeping

If D or R are engaged withthe engine running and the

footbrake is then released, on aflat surface the vehicle will slowlymove off on its own (creepfunction).

A cold engine runs at a higher idlingspeed after starting causing anincrease in creep speed (manualand Auto mode).

On a gradient the vehicle may notcreep, depending on the steepnessof the incline and the weight of thevehicle.

The creep function is turned offwhen the handbrake or footbrake isapplied.

To protect the clutch from damagethe creep will be disabled when theclutch temperature is too high.

Never press accelerator and brake pedals

simultaneously.

Driving

116

Gear display

The display in the instrumentcluster shows the gear positioncurrently selected.

Auto is displayed when automatedmode is selected.

A flashing gear within the displayindicates a requested gear. Driveraction may be required. See alsosections Vehicles with Durashift

EST, page 115, D = Drive, page117, and Stopping, page 120.

Selector lever positions

Apply the handbrake ordepress the footbrake

before selecting a gear. Failure todo so could result in the vehiclepulling away when you haveengaged a gear.

N = Neutral

Note: In this position no gear isselected. To prevent the vehiclefrom moving you have to depressthe footbrake or to apply thehandbrake.

Driving

117

R = Reverse

Select this position onlywhen the vehicle is

stationary and the engine isidling.

To shift into reverse gear, thefootbrake needs to be depresseduntil reverse gear is engaged.

D = Drive (automated mode)

Depress the footbrake and movethe selector lever from N to D. Thetransmission will be in automatedmode and first gear will be engaged.

In this mode gear changes will bemade automatically depending ondriving conditions.

If the footbrake is not pressed whenmoving selector from N to D thedisplay will flash. Return theselector to N and repeat theprocess with the footbrakedepressed or press the acceleratordirectly.

Driving

118

When in automated mode andselector positions +, – or A are usedmanual mode will be selected. Thedisplay will show the currentengaged gear.

A = Mode change

It is possible to change betweenautomatic and manual mode at anytime by pushing the shift lever toposition A and releasing.

+/– = Manual mode

Do not hold the shift leverpermanently in A, + or –.

In manual mode the gears can bechanged manually.

+ Shifts to a higher gear

– Shifts to a lower gear.

Gears can be skipped by moving theselector repeatedly at shortintervals.

Note: If a higher gear is requestedwhen the speed is too low, or alower gear when the speed is toohigh no shift will occur. This willprevent the engine from running attoo high/low revolutions.

To avoid engine stall thetransmission will automaticallydownshift when the vehicle speed istoo low.

Driving

119

Driving with Durashift EST

Moving off

Depress the footbrake and movethe selector lever from N to D. Thetransmission will be in automatedmode and first gear will be engaged.

When the footbrake is released, ona flat surface the vehicle will creep.See also the sections Creeping,page 115, Stopping, page 120 andDriving on inclines, page 121.

Press the accelerator pedal to driveaway.

• Moving away in sand, mud orsnow

If it becomes necessary to rock thevehicle to free it from snow, mudetc. move the selector leverbetween D and R repeatedly whilstapplying light pressure to theaccelerator pedal.

Do not race the engine andavoid sudden acceleration.

To protect the system the startingoff aid is disabled at very highclutch temperatures.

On vehicles with a petrol engineand in manual mode the secondgear can be selected by using + toimprove pulling away in winterconditions etc..

Driving

120

Downshift (Kickdown)(Automated mode only)

When the accelerator pedal isdepressed beyond its resistancepoint the transmission willdown-shift into a lower gear. Thiswill make full use of the enginetorque when overtaking or drivingup steep gradients.

When the engine speed approachesits upper limit the transmission willshift into a higher gear.

Stopping

When stopping or waitingon a gradient always apply

the handbrake. To preventoverheating of the clutch do notincrease the engine revolutions.

When the selector is in the Dposition and the vehicle is atstandstill, 1st gear will be engagedautomatically.

Before exiting the vehicle with theengine still running place theselector in N and apply thehandbrake.

Note: If the selector is moved to agear, the engine is running and thedriver’s door is open, and no brakepedal pressed, a warning signal willsound and the gear display willflash.


Driving

121

Parking with Durashift EST

Before leaving the vehiclealways apply the

handbrake. If the engine is leftrunning move the selector leverto N.

To park in gear the ignition shouldbe on and the brake pedaldepressed. The last gear engagedwill be retained.

When the selector lever is inposition N no gear will be retainedand the vehicle is parked inNeutral.

When the ignition is switched offthe transmission no longerresponds to movement of the shiftlever.

Driving on inclines

• Hill starts

Do not hold the vehicle on a hill oragainst a kerb using acceleratorpedal.

If the clutch becomes overheated awarning will be activated. TheTransmission/Engine systems faultwarning light illuminates (see alsopage 122) and the clutch will pulse.Normal operation will return whenthe clutch has cooled down.

• Automated mode

When driving, a higher gear will notbe selected until a reasonably highengine speed has been achieved.

• Manual mode

To utilise engine braking select alower gear when driving down hill.

Adaptive Shift Programmes

Adaptive programmes automaticallyadapt gear shifting to suit thedriving conditions such as if thevehicle is towing a caravan/trailer,has a high payload or is beingdriven on steep inclines.

Driving

122

WARNING LIGHTS ANDMESSAGES

Transmission/Engine systemsfault warning

A malfunction of the engine andpowertrain related systems isindicated by the following:

1. The Transmission/Enginesystems fault warning lightilluminates permanently whendriving.

The vehicle can still be driven. Aminor reduction in performancemay occur such as reduced powerand/or acceleration.

Have your vehicle checked by anexpert as soon as possible.

2. If the Transmission/Enginesystems fault warning light flasheswhen driving, stop the vehicle assoon as safely possible and switchoff the engine immediately.

Have the engine checked by anexpert immediately.

In addition, on vehicles with aMessage Centre, this message willappear in the display.

The display warning lightilluminates amber (point 1) or red(point 2).

Vehicles with Durashift EST

In addition this message mayappear in the display and thedisplay warning light illuminatesred.

Refer to point 1.

Vehicles with automatictransmission

See also sections Hot mode andEmergency mode, page 113onwards.

Driving

123

Engine warning light

If the engine warning lightilluminates with the engine running,it indicates a malfunction.

If the engine warning light flasheswhen driving, reduce the vehiclespeed immediately. If it continuesto flash, avoid heavy accelerationand high engine speed.

Have your vehicle checked by anexpert immediately.

Power steering failure(vehicles with 1.6 l Duratorq-TDCiengine)

If the Power assisted steeringwarning light illuminates whendriving, it indicates a malfunction ofthe power assisted steering system.


Full steering will be maintained butyou will need to exert greater forceon the steering wheel.

Have the system checked by anexpert as soon as possible.

Driving

124

Frost warning

At temperatures between +4 ºC and+1 ºC, the orange Frost warninglight illuminates. At temperaturesbelow +1 ºC, the warning lightglows red.

In addition, on vehicles with aMessage Centre, this message willappear in the display and thedisplay warning light illuminates.

A warning chime will sound in thefollowing conditions:

+4 ºC or lower: frost warning(if all chimes are activated only, seealso section Chimes, page 34)The display warning lightilluminates amber.

0 ºC or lower: danger of icy roadsThe display warning lightilluminates red.



Even if the temperaturerises to above +4 ºC there is

no guarantee that the road is freeof hazards caused by inclementweather.

REFUELLING

Low fuel level warning light

If the fuel level is about 15 % of thetank capacity or below, the Low fuellevel warning light illuminates.Refuel as soon as possible. Pleaserefer also to section Fuel gauge,page 19.

In addition, on vehicles with aMessage Centre, a warning chimewill sound at the following ranges(if all chimes are activated only, seealso section Chimes, page 34):80 km, 40 km, 20 km and 0 km.Refer also to section Distance to

empty, page 25.

Diesel low fuel safety mode

In the case that the vehicle runs outof fuel:

• Switch off the ignition.

• Fill up the fuel tank with aminimum of 7 litres.

• Turn the key to position II for3 seconds.

• Start the engine.

For further information, see alsothe section Diesel low fuel safety

mode on page 9.

Driving

125

Fuel filler flap

To unlock the filler flap, turn thekey clockwise and open. Turn thecap anticlockwise and remove.

When the filler cap is removed, ahissing noise may be heard. This isnormal and should be disregarded.

To close, turn the cap clockwiseuntil it engages.

Filling up

Refer also to the section Fuel,page 172.

To avoid fuel spillage thatcould be hazardous to other

road users, always stop refuellingafter the fuel nozzle stops thesecond time. Additional fuel willfill the expansion space in the fueltank which could lead to fueloverflowing.

The fuel system is underpressure. There is a risk of

injury if the fuel system is leaking.Do not use any kind of flames orheat near the fuel system.

Incorrect fuel

If you fill your vehicle withincorrect fuel or additives,

do not attempt to start theengine. This may lead to enginedamage.

Driving

126

DRIVING WITH A CATALYTICCONVERTER

• Avoid running out of fuel.

• Avoid unnecessarily long enginecranking periods.

• Do not run the engine with adisconnected spark plug.

• Do not push-start or tow-start thevehicle; use jump leads.

• Never switch off the ignitionwhile driving.

Parking

It is important to avoidparking, idling or operating

the vehicle on dry leaves or drygrass. Even when the engine isswitched off, the exhaust willcontinue to radiate a considerableamount of heat for a short periodcreating a potential fire hazard.

VEHICLE LOADING

Transporting luggage

Luggage and other loadsshould be placed as low and

as far forward as possible withinthe luggage compartment. Drivingwith the tailgate/rear door open ispotentially dangerous as exhaustfumes may be drawn into thevehicle’s interior.

Driving

127

If objects have to be placedin the vehicle, secure them

from moving.

Luggage cover

Do not place objects on theluggage cover.

Removal

Detach the two lifting straps on thetailgate. Release the cover at itssides and pull it out horizontallywithout tilting it.

Refitting

Insert the cover horizontally, align itand push in as far as the stop.Attach the lifting straps to thetailgate.

Driving

128

Luggage net

In order to secure light objects, aluggage net can be fastened to bothsides of the trim in the luggagecompartment.

STORAGE AREAS

Front storage compartment

Press the button to open.

To close, push the cover down untilit engages.

Note: Avoid keeping heat-sensitiveobjects in the front storagecompartment.

Never drive with the frontstorage compartment lid

open. This will obscure yourvision out of the front screen.Before setting off, always ensurethat the lid is securely engaged.

Storage area passenger side

Storage compartment

A storage compartment is providedunderneath the instrument panelon the drivers side.

Driving

129

Glove compartment

Card holder

Coin holders

Pen/pencil clip

Under-seat storage

The storage box is located underthe front passenger seat.

• To open: Pull the front of the seatcushion up .

• Pull the seat cushion towards theinstrument panel .

• Lift the seat cushion to reveal thestorage area .

• To close, follow the above steps inreverse, making sure that you pushthe seat cushion downwards until itlocks into place.

Driving

130

Map pockets

The map pockets are located on therear of the front seatbacks.

Coin holder

Depending on model variant coinholders are provided on theinstrument panel.

Storage pockets(depending on model variant)

Driver’s seat

Rear seats

Driving

131

Installing the activity console(depending on model variant)

The activity console can beinstalled in the centre of the rearseat after removing the seatcushion.

To remove the seat cushion, pullthe loop at the bottom front edgeand take it out.

Gently press the console down untila distinct click is heard.

Press the rear half of the button toopen the storage compartment.

Driving

132

Press on the front half of the buttonto open the cupholders.

The cup holders can be removed toprovide additional storage capacity.

To avoid scalding, neverplace hot drinks in the cup

holders while driving.

To remove the console, gently pullthe front handle and take it out.

To reinstall the cushion, press itdown until it engages in its catch.

Ensure that the cushion isengaged properly and the

loop is not caught.

Driving

133

TRAILER TOWING

If your vehicle has adetachable towball arm,

remove and reinstall it regularlyto keep the locking mechanismworking smoothly.

The maximum vehicle and trailerpayloads represent technicallybinding values for gradients up to12 % and an altitude of 1 000 metres above sea level.

In high altitude regions, thinneratmosphere can reduce engineperformance so the followingrestrictions will apply:

Above 1 000 metres, the stipulatedmaximum permitted gross trainweight must be reduced by 10 % forevery 1 000 metres in altitude.

Steep gradients

Change down in plenty of timebefore downhill gradients.

If you have automatic transmission,according to the gradient, switch offthe overdrive or select position 2 or1 when going down steep hills.

For going up steep hills, refer to thesection Uphill mode, page 112.

The overrun brake on atrailer is not controlled by

the anti-lock braking system.

Detachable towball arm

Always remove the towballarm when it is not in use.

The towball arm must bestored securely in the

luggage compartment at all timeswhen detached.

Driving

134

Unlocking the towball armmechanism

• Remove the protecting cap. Insertthe key and turn anticlockwise tounlock.

• Hold the towball arm. Pull thehandwheel out and turn itclockwise until it clicks.

• The red mark on the handwheelmust align with the white mark onthe towball.

• Release the handwheel. Thetowball arm is unlocked.

Do not use any tools formounting/dismounting the

towball arm. Do not modify thetrailer coupling. Do notdisassemble/repair the towballarm.

Inserting the towball arm

Special care should betaken when fitting the

towball arm, as the safety of thevehicle and the trailer depends onthis.

The towball arm may beinserted only when

completely unlocked.

• Pull out the plug of the towballarm’s seat.

Driving

135

• Ensure that the towball armhandwheel is in the correct positionwith the red mark next to the whitedot.

• Insert the towball arm verticallyand push it up until the lockingmechanism engages automatically.When the towball arm is engaged,the green mark on the handwheelwill be next to the white dot.

• To lock: Turn the key clockwise.

• Pull out the key and insert theend of the protection cap into thekeyhole.

Driving with a trailer

Before starting your journey, ensurethe towball arm is properly locked.Check:

• The green mark on thehandwheel has to be next to thewhite dot on the towball arm.

• The key has been removed.

• Secure positioning of the towballarm. (Must remain perfectly inplace when jerked.)

• Attach the safety cable to thesafety cable eye.

Never attach the safetycable directly to the towball

arm.

If any of the aboveconditions cannot be met,

do not use the tow bar and have itinspected by an expert.

Driving

136

Removing the towball arm

• Remove the protection capcovering the keyhole.

• Insert the key and turn itanti-clockwise to unlock. The arrowon the key points to the unlocksymbol on the handwheel.

• Pull out the handwheel and turnit clockwise until the red mark isnext to the white dot.

• Pull the towball arm downwardsto remove.

• Insert the plug into its seat afterremoving the towball arm.

To avoid risk of injury, neverunlock the towball arm with

the trailer attached.

Maintenance

Keep the system clean. Periodicallylubricate the lock with graphite.

Remove the towball armand protect the seat with

the plug before steam cleaningyour vehicle.

Keep a note of the key number.

ROOF RACK

Driving with a roof load canhave a negative influence on

the driveability of the vehicle.

When driving with a roofload, the ESP system (if

equipped) must always beswitched on.

If the vehicle is used with aroof load, or is fully laden,

the tyres must be set to standardtyre pressure setting.

Driving

137

ULTRASONIC PARK DISTANCESENSOR

The park distance sensor isan auxiliary system which is

not intended to relieve the driverof his responsibility for exercisingdue care and attention whenreversing. In particular, someobjects close to the vehicle(approx. 30 cm) and above orbelow the sensors may not bedetected by the park distancesensor and cause damage to thevehicle. Ultrasonic waves, heavyrain and/or conditions causingdisruptive reflections may lead toobjects not being detected by thesensors. In addition, objectswhich absorb ultrasonic wavesmay not always be detected dueto their unfavourable surfacecharacteristics.

The system is activatedautomatically after the ignition isswitched on and the reverse gear isselected. A short tone will sound toindicate system readiness.

A system failure will be indicated bya deep continuous tone or by adeep tone sounding in three-secondintervals. In both cases the systemis not reliable.

Have the system checked by anexpert.

The measuring range is dividedinto five warning zones. As thedistance to an obstacle reduces, awarning sounds, beginning as aslow bleep and increasing to acontinuous tone.

Always keep the sensors free fromdirt, ice and snow (do not cleanwith sharp objects).

Roadside emergencies

138

HAZARD FLASHER SWITCH

Press the switch to turn on or off.The hazard flasher switch does notflash. The hazard lights can beoperated when the ignition is off.

FIRST AID KIT AND WARNINGTRIANGLE

A retaining strap on the right-handside of the luggage compartmentcan be used to secure a first aid kitbox.

A retaining strap on the rear panelof the luggage compartment can beused to secure a warning triangle.

LIMITED OPERATIONSTRATEGY PROGRAMME

The engine management systemincorporates a Limited OperationStrategy programme. If a faultoccurs in the system, the enginewill still function but performancemay be reduced.

The vehicle can be driven at roadspeeds of up to 60 km/h on levelsurfaces.

Have the vehicle checkedby an expert immediately.


139

FUEL INJECTION SYSTEMSHUT-OFF SWITCH(vehicles with a petrol engine)

The fuel supply may be cut off as aresult of an accident or suddenvibrations (e.g. collision whenparking).

The switch is located behind theglove compartment.

Open the glove compartment andempty it before continuing. Pressthe side parts of the glovecompartment inwards and swivelthe compartment further down.

The button under the yellow capwill be raised when the switch isactivated.

Resetting the switch

Do not reset the fuel pumpshut-off switch if you see or

smell leaking fuel.

• Turn the ignition switch toposition 0.

• Check the fuel system for leaks.

• If no fuel leak is apparent, resetthe switch by pushing in the button.

• Turn the ignition switch toposition II. After a few secondsreturn the key to position I.

• Make a further check for leaks inthe fuel system.


140

FUSES

Switch off the ignition andall the electrical equipment

before changing a fuse.

Always replace a faulty fuse with anew one of the same rating.

Any improper alterations tothe electrical or fuel system

can endanger the safety of thevehicle as they could constitute afire hazard or cause enginedamage. Have any work involvingthese systems or the replacementof relays or high current carryingfuses carried out by an expert.

Central fuse box

The central fuse box is locatedbehind the glove compartment inthe instrument panel.

To gain access to the fuse box:

• Open the glove compartment andempty it before continuing.

• Press the side parts of the glovecompartment inwards and swivelthe compartment further down.

Fuse chart label

Fuses

• Reinstall in the reverse order.


141

Fuse chart label

The fuse chart label showsrectangles representing a fuse. Thefollowing information is shown inthe rectangles:

Number of the fuse (F).

Symbol of the function, seetable on the following page.

L = left-hand side,R = right-hand side.

Ampere rating of the fuse.

Symbols in the fuse boxes

Symbol Definition

See Owner’s Handbook

Airbag

ABS

Dipped beam

Main beam

Fog lights

Light switch

Front wiper


142

Symbol Definition

Rear wiper

Heated front screen

Heated rear screen

Heated mirror

Electrically operatedoutside rear-viewmirrors

Front power windows

Electrically operatedsunroof (not used)

Heated seats

Symbol Definition

Heater blower

Air conditioning

Cigar lighter

Horn

Daytime running light(Scandinavia only)

Automatictransmission/Durashift EST

Engine management(Diesel only) orcatalytic converter

Starter motor


143

Symbol Definition

Audio, diagnostic plug

Engine managementor electronic module

Fuel pump

Auxiliary heater/Diesel glow plug/Injector pump relay/Fuel fired heater

Battery, alternator

Instrument cluster,battery saver, numberplate light, genericelectronic module

Side and tail lights

Central locking, alarmhorn

Symbol Definition

Hazard flasher,direction indicator

Ignition

Trailer towing module

Durashift EST

Brake light

Reversing light


144

BULB REPLACEMENT

Always switch off lights and ignitionbefore replacing any bulb.

Never touch the glass of the bulbs.Fit only bulbs having a UV filter.Always replace a faulty bulb with anew one of the same type. Afterreplacing a bulb, check that thelights operate correctly.

Have the headlightalignment checked after

each replacement of a bulb.

During operation, the bulbsand their surroundings get

hot. Switch off the lights and letthe bulbs cool down beforereplacing them.

Headlights, side lights, directionindicators

It is necessary to remove the lightassembly to remove any of thebulbs.

Removing the light assembly

1. Open the bonnet.

2. Remove the screws in the lightassembly.

3. Carefully pull out the lightassembly from the side and top clipand disconnect the wiringconnector.

Note: When installing in thereverse order, first fix the hook/pinunder the fender to get the rightposition for the other locator arms.Make sure that the side clipengages properly.


145

When re-installing the lightassembly, make sure that

the wiring connector is engagedproperly and that the wireharness is securely snapped intothe clip-in feature on the rear ofthe light assembly.

Front direction indicator

21 watt spherical bulb, orange

1. Turn the bulb holderanticlockwise and pull out.

2. Turn the bulb under slightpressure anticlockwise and removeit.

3. Replace the bulb.

When installing in the reverseorder, pay attention to the guidetabs.

Opening the headlight assembly

1. Remove the cover.


146

• Headlights – main/dippedbeam

H4, 55/60 watt halogen bulb

1. Pull off the wiring connector.

2. Disengage the wire clip and pullout the bulb.


When installing in the reverseorder, make sure the wire clipengages properly to bulb housing.

• Side lights

5 watt wedge base bulb

1. Carefully prise out the socket.

2. Pull out the bulb and replace it.

Install in the reverse order.


147

Side repeater indicator


1. Carefully pull out the lightassembly, complete with the bulbholder.

2. Grasp the bulb holder, turn thelight housing anticlockwise andremove it.

3. Pull the bulb out and replace it.


Front fog lights

H11, 55 watt halogen bulb

1. Reach behind the bumper andpull off the wiring connector.

2. Turn the bulb holderanticlockwise and pull it out.

3. Replace the bulb with theintegrated bulb holder.



148

Rear lights

1. Open the tailgate.

2. From inside the luggagecompartment, lift the flap in thetrim panel and remove the wing nuton the rear of the light assembly.

3. Remove the screws on the frontof the rear light assembly andcarefully pull it out.

4. Open the 6 clips and remove theentire bulb holder.

Brake/tail light 21/5 watt

Direction indicator 21 watt (orange bulb)

Reversing light 21 watt

Rear fog light 21 watt

5. Turn the bulb anticlockwiseunder slight pressure, and removeit.




149

High mounted central brakelight


1. Open the tailgate and removethe rubber grommet.

2. Depress the metal springsthrough the aperture using aflat-bladed screwdriver.

3. Unclip the light assembly.

4. Unclip the bulb holder from thelight assembly.



Number plate light

ZW5 watt festoon bulb

1. Loosen the screws, and removethe light assembly.



Interior lights

10 watt festoon bulb

1. Switch off the interior lights(left switch position).

2. Prise out the light assembly atthe side opposite the switch with aflat-bladed screwdriver.

3. Remove the reflector.

4. Remove the bulb and replace it.



150

Reading lights

5 watt spherical bulb

The bulbs can be replaced after thecontact plate has been hinged back.

Reading lights(depending on model variant)


1. Carefully prise out the lens.


Luggage compartment light


1. Carefully prise out the lightassembly from the holder with aflat-bladed screwdriver.

2. Remove the bulb and replace it.



151

CHANGING A WHEEL

• Park your vehicle in sucha position that neither the

traffic nor you are hindered orendangered when changing awheel.

• Set up a warning triangle.

• Ensure that the vehicle is onfirm, level ground.

• If necessary, secure the vehiclewith suitable chocks.

• Point the front wheels straightahead.

• Switch off the ignition andapply the handbrake.

• Select first or reverse gear.

With Durashift EST, depress thefootbrake and select the gearbefore switching off the ignition.

If the vehicle has an automatictransmission, select the Pposition.

The vehicle jack must onlybe used to carry out wheel

changes. Do not work under thevehicle when it is supported onlyby the jack.

If your vehicle is fitted withdirectional tyres, make sure

that the arrows on the tyres pointin the direction of rotation whenthe vehicle is moving forwards.The arrows on both tyre sidewallsindicate the direction of rotation.

If a spare wheel has to be fittedwith the arrows pointing in theopposite direction to the directionof rotation, have the tyreremounted in the correctdirection by an expert as soon aspossible.

Spare wheel

Use only approved wheeland tyre sizes. Using other

sizes could damage the vehicleand will make the National TypeApproval invalid.

If the spare wheel differsfrom the other fitted

wheels, these rules must befollowed:

• Do not exceed 80 km/h.

• Drive the shortest possibledistances.

• Do not fit more than one sparewheel on your vehicle at any onetime.


152

• Do not use snow chains on thistype of wheel.

• Do not drive through anautomatic car wash.

• Vehicles with Electronic StabilityProgram (ESP) may exhibit someunusual driving characteristics.Switch the ESP off. Refer to thesection Electronic Stability

Program (ESP), page 101onwards.

• If the spare wheel is used on therear axle of vehicles with DurashiftEST, the system may not be able toselect a higher gear in automatedmode (AUTO). This is due to thedifferent size of the spare wheeland the standard wheel/tyrecombination. Select manual modeto shift into a higher gear. Afterreplacing the spare wheel with thestandard wheel, normal operation inautomated mode (AUTO) willreturn.

The vehicle may exhibitsome unusual driving

characteristics or engineoverheating may occur if you usethe spare wheel on the rear axlein automated mode (AUTO) forlonger than a temporary period.Select manual mode to shiftgears.

The spare wheel is located underthe floor cover in the luggagecompartment.

• Raise the rear of the floor cover inthe luggage compartment andremove it.

• Completely unscrew the retainingdevice anticlockwise.

• Remove the spare wheel cover.

• Lift out the spare wheel.

• Install the defective wheel in thereverse order.


153

Vehicle jack

The jack and wheelbrace arelocated in the spare wheel well.Unscrew the retaining device byturning anticlockwise, and removethe jack with the wheelbrace.

Remove the clipped on towing eye.

Note: When reinstalling, use theleft hole in the jack for the jackretaining device and the right holefor the spare wheel retainingdevice.

Jacking points

The jack must only be used on thesmall indentations under thesills.

The jack must be appliedvertically to the jacking

point.


154

Points can be used for trolleyjacks, workshop hoists or jackstands. Points can be used fortrolley jacks in the centre, front orrear.

Positioning at other points maycause considerable damage to thebody, steering, suspension, engine,braking system or fuel lines.

Removing a wheel

• Make sure that the vehicle is on aflat surface and the front wheels arepointing straight ahead.

• Switch off the ignition and applythe handbrake.

• Select reverse or 1st gear.

With Durashift EST, depress thefootbrake and select the gear beforeswitching off the ignition.

If the vehicle has an automatictransmission select the P position.

• Have the passengers leave thevehicle.

• If necessary, secure the vehicleagainst rolling or sliding by usingsuitable wheel chocks.

• Insert the flat end of thewheelbrace between the rim andthe hub cover and twist carefully toremove the cover.


155

• Insert the nut key onto thelocking nut (if equipped).

• Slacken the wheel nuts.

• Place the jack with the whole footarea on firm ground.

• Jack up the vehicle until thewheel is clear of the ground.

• If the whole foot area does notremain on the ground, lower thevehicle and reposition the jack.

• Unscrew and remove the wheelnuts and take off the wheel.

Replacement locks and wheel nutscan be obtained using the wheel nutreference number certificate (ifequipped).

Fitting a wheel

Alloy wheels must never besecured using wheel nuts for

steel wheels.

• Push the wheel onto the wheelstuds. Screw on the wheel nuts andsecure in a clockwise directionensuring that the tapered end ofthe wheel nuts is facing the wheel.

Note: The wheel nuts of alloywheels can also be used for thesteel spare wheel for a short time(maximum two weeks).

• Lower the vehicle and remove thejack.

• Insert the nut key onto thelocking nut (if equipped).


156

• Fully tighten the wheel nuts inthe pattern shown.

• Press on the hub cap firmly withthe ball of the hand.

• Stow the locking nut key in a safeplace.

• Stow the jack and defective wheelin reverse order and secure them(see note on page 153).

Have the tightening torque of thewheel nuts and the tyre pressurechecked as soon as possible.

BATTERY

Maintenance

The battery requires very littlemaintenance. The fluid level ischecked during the routine serviceinspections.

Ignition warning light

If it illuminates whilst driving,switch off all unnecessary electricalequipment and drive immediatelyto the nearest expert.

Removal and installation

If the battery has beendisconnected the vehicle mayexhibit some unusual drivingcharacteristics for approximately8 km after battery reconnectionwhile the engine managementsystem realigns itself with theengine.

The audio system must bereprogrammed with the keycode.Refer to the separate manual.


157

JUMP STARTING

Connect batteries with only thesame nominal voltage (12 volts).Use jump leads with insulatedclamps and adequate size cable. Donot disconnect the battery from thevehicle’s electrical system.

To connect the leads

• Position the vehicles so that theydo not touch one another.

• Switch off the engine. Switch offelectrical equipment.

• Connect the positive (+) terminalof the flat battery to the positive(+) terminal of the booster battery

.

• Connect one end of the secondlead to the negative (–) terminalof the booster battery .

• Do not connect to thenegative (–) terminal of the flatbattery.

• On vehicles with a petrolengine, connect the other end oflead as far away from the batteryas possible to the engine block orthe engine mount of the engine tobe started.

• On vehicles with a dieselengine, connect the other end oflead to the turbo charger ofthe engine to be started (as shownin the graphic).

• Make sure that the jump leads areclear of moving parts of the engine.

Flat battery

Booster battery


158

To start the engine

• Run the engine of the vehiclewith the booster battery atmoderately high speed.

• Start the engine of the vehiclewith the flat battery.

• Run both vehicles for a minimumof three minutes beforedisconnecting the leads.

Do not switch on theheadlights when

disconnecting the leads. The peakvoltage could blow the bulbs.

• Disconnect the leads in thereverse order.

TOWING THE VEHICLE

The screw-in towing eye is attachedto the jack in the luggagecompartment.

The towing eye must always becarried in the vehicle.

Press the lower part of the cover inthe front bumper and prise it off.Install the towing eye.

The screw-in towing eyehas a left-hand thread.

Install it by turninganticlockwise. Use thewheelbrace to ensure the towingeye is fully tightened.

After use, unscrew the towing eyeand re-insert the cover.


159

Rear towing eye

Before using the rear towing eye,remove the cover. After use,reinstall the cover to its originalposition.

When towing always drive off slowlyand smoothly without jerking thetowing vehicle. Excessive tow ropetension could result in damage toeither vehicle.

Note: Observe the safetyregulations that are valid for towinga vehicle depending on country.

The ignition key must be setto position II when the

vehicle is being towed so that thesteering, direction indicator lightsand brake lights are fullyoperational. Since the brake servoand the power steering do notoperate with the engine switchedoff, you will need to exert greaterforce to the brake pedal andsteering wheel. Make allowancesfor the increased braking distanceand heavier steering.

Towing vehicles with DurashiftEST

When a vehicle with Durashift ESTis towed, N (Neutral) must beselected.


160

Towing vehicles with automatictransmission

When a vehicle with an automatictransmission is towed, the selectorlever must be in position N(neutral).

Never tow a vehicle with anautomatic transmission

faster than 50 km/h or furtherthan 50 kilometres.

If it is necessary to tow the vehiclea greater distance, the drive wheelsmust be lifted clear off the ground.

Never tow a vehiclebackwards with the drive

wheels turning. If this instructionis not adhered to, it could causedamage to the automatictransmission.

Starting vehicles by towing orpushing

To prevent damage youmust not push- or tow-start

your vehicle. Use jump leads anda booster battery.

Cleaning

161

WASHING YOUR VEHICLE

The best procedure is brushlesswashing in a good car washinstallation.

In installations operatingwith high water pressure,

water might be forced into thevehicle’s interior or parts may getdamaged.

Unscrew and remove theradio aerial before entering

an automatic car wash. Switch offthe heater blower to preventcontamination of the fresh airfilter.

If a waxing cycle is selected, pleaseensure that the wax is removedfrom the front screen afterwards.

Cleaning the headlights

To avoid damaging the clear plasticheadlight lens do not use aggressiveabrasives or chemical solvents. Donot wipe the lights when they aredry or use sharp objects to cleanthe lenses.

Cleaning the rear screen

To avoid damaging the heatingelements when cleaning the insideof the rear screen use only a softcloth or a damp chamois leather. Donot use solvent or sharp objects toclean the glass.

Cleaning seat belts

Use Interior Cleaner or clean warmwater. Dry naturally, away fromartificial heat.

Do not use chemical cleaners,boiling water, bleach, or dye. Do notallow moisture to penetrate the seatbelt retractor mechanism.

Cleaning

162

PAINT CHIP REPAIR

Paint damage from road chippingsor minor scratches can be repairedusing aerosol paint spray ortouch-up paint. The Ford Accessoryrange is recommended. Observe theapplication instruction on eachproduct.

To retain vehicle warrantyon paintwork, remove

apparently harmless looking butoften aggressive particles fromthe paintwork immediately - e.g.bird droppings, tree resins, insectremains, tar spots, road salt andindustrial fall-out.

BODY PAINTWORKPRESERVATION

Wax the body paintwork of yourvehicle once or twice a year. Thiswill help retain the glossy paintworkfinish and water droplets will runoff more easily.

When polishing your vehicleensure that polish does not

come into contact with the plasticsurfaces as it may prove difficultto remove.

Do not polish the vehicle in strongsunshine.

Do not apply polish to front or rearscreen, as this may result in poor ornoisy wiper action.

Maintenance

163

SERVICING

• Check and top up fluid levelsregularly.

• Check tyre pressure.

• Check brakes and lights areoperating correctly.

• Check warning and indicatorlights.

The electronic ignitionsystem works with high

voltage. Never touch thesecomponents with the enginerunning or the ignition switchedon.

The ignition must beswitched off before working

in the engine compartment.Under some operating conditions,the cooling system fan maycontinue to run for severalminutes after the engine has beenswitched off. This is quite normal.

Take care not to get any fingers orclothing such as ties or scarvescaught in the fan.

Maintenance chart

Every day check:

• Operation of all exterior andinterior lights and make surethat all lenses are clean.

When refuelling check:

• Engine oil level

• Brake fluid level

• Screen washer fluid level

• Tyre pressures and condition(only when cold)

Once a month check:

• Coolant level (engine cold)

• Assemblies, pipes, hoses andreservoirs for leaks

• Power steering fluid level

• Operation of air conditioning

• Operation of handbrake

• Operation of horn

Note: The air conditioning shouldbe used for at least 30 minutes permonth.

Maintenance

164

Opening the bonnet

• Pull the bonnet release lever situated in the left-hand sidefootwell.

• Push the safety catch to theleft to release it.

• Raise the bonnet fully andsupport its strut in the retainer ensuring it is secure.

To close, lower the bonnet andallow it to drop into the catch forthe last 30 cm.

Always check to ensure that thebonnet lock is fully engaged.

Maintenance

165

Engine compartment


Engine coolant reservoir1 169

Engine oil filler cap1 168

Auxiliary fuse box −2

Brake/clutch fluid reservoir1 168

Battery 156

Screen washer fluid reservoir(Power steering fluid reservoir3)

170

Air cleanerNo maintenance

necessary

Engine oil dipstick1 167

Power steering fluid reservoir(Screen washer fluid reservoir3)

170

1 For easy identification, filler caps and the engine oil dipstick are marked in colour.2 The replacement of these fuses/relays requires specialised knowledge.

Please ask an expert to check them.3 1.6 l Duratorq-TDCi engine only.

1.25/1.4/1.6 l Duratec

Maintenance

166

1.4 l Duratorq-TDCi

1.6 l Duratorq-TDCi

Maintenance

167

Engine oil dipstick

The oil consumption of new enginesreaches the normal value only afterapproximately 5 000 km.

Make sure the vehicle is standingon level ground. Check the engineoil before starting the engine. If theengine was running, switch it offand wait some minutes for theengine oil to flow back into thesump before checking it. Pull outthe dipstick, wipe it with a clean,non-fluffy cloth, re-insert itcompletely and pull it out oncemore.

If the level lies between the marks,there is no need to refill. Hot oilmay exceed the MAX mark by somemillimetres due to thermalexpansion.

If it lies at the MIN mark refill usingonly engine oil meeting the Fordspecification.

Top up to only the upper mark(MAX).

For further details, refer to sectionEngine oil, page 174 and tableCapacities, page 174.

1.25/1.4/1.6 l Duratec engine

1.4 l Duratorq-TDCi engine


Maintenance

168

Oil pressure warning light

If the light stays on after starting orilluminates during a journey, stopimmediately, switch off the engineand check the engine oil level.

Top up straight away if the level islow.

Do not resume the journeyif the oil level is correct.

Have the engine checked by anexpert.

Engine oil filler cap

To open, turn in the direction of thearrow and pull. Do not open the capwhile the engine is running.

Do not use oil additives orother engine treatments.

They are unnecessary and could,under certain conditions, lead toengine damage which is notcovered by Ford Warranty.

To close, turn the cap clockwiseuntil it is fully tightened.

Brake/clutch fluid reservoir

Do not allow this fluid tomake contact with the skin

or eyes. If this should happenrinse the affected areasimmediately with plenty of waterand contact your doctor.

Brake and clutch fluid systems aresupplied from the same reservoir.

The level of the fluid must liebetween the MIN and MAX markson the side of the reservoir.

If the level falls below the MINmark, the Brake system warninglight will illuminate. Refer to thesection Brake system warning,page 98.

Maintenance

169

Cooling system reservoir

To avoid scalding, neverremove the cap from the

coolant reservoir when the engineis hot. Do not restart the engineuntil the problem has beeneliminated.

The coolant level is visible throughthe translucent reservoir.

The coolant level should bebetween the MIN and the MAXmark when the engine is cold. Hotcoolant expands and may,therefore, extend beyond the MAXmark.

The coolant should be added whenthe engine is cold. If coolant has tobe added when the engine is hot,first wait 10 minutes for the engineto cool.

Unscrew the cap slowly. Anypressure will escape while you areturning the cap. Fully remove thecap.

Take great care whenadding coolant. Avoid

spillage on any part of the engine.

When the vehicle is new, thecooling system is filled with coolantwhich offers anti-freeze protectiondown to approximately −25 ºC.

Add only coolant that meets theFord Specification. For furtherdetails, refer to section Vehicle

fluids, page 174.

Engine coolant temperaturewarning

On vehicles with a Message Centre,this message will appear in thedisplay and the display warninglight illuminates red.

Refer also to the section Engine

coolant temperature gauge,page 19.

Engine coolant

Do not allow this fluid tomake contact with the skin

or eyes. If this should happenrinse the affected areasimmediately with plenty of waterand contact your doctor.

Maintenance

170

Checking power steering fluidlevel

The fluid level should come up tothe MAX mark when the engine iscold.

If it drops below the MIN mark, topup with the specified fluid. Forfurther details, refer to sectionVehicle fluids, page 174.


No fluid level checks are necessary.

Screen washer systems

Front and rear washer systems aresupplied from the same reservoir.

Replace the cap securely aftertopping up.

Adjusting screen washer jets

The eye ball jets can be adjustedprecisely using a pin.

The washer jet for the rear screenis located on the high mountedcentral brake light.

Maintenance

171

Checking wiper blades

Check the wiper blades on yourvehicle for roughness by runningthe tip of your fingers over the edgeof the blade. Clean the wiper bladelips with water applied with a softsponge.

Renewing wiper blades

Lift the wiper arm and position thewiper blade at a right angle to thewiper arm. To remove, press theretaining clip in the direction of thearrow, disengage the wiper bladeand pull it off the arm in theopposite direction.

TYRE INFORMATION

To make sure the front and reartyres wear evenly and last longer, itis recommended that you swap thetyres from front to rear and viceversa at regular intervals of 5 000 to10 000 km as shown in the graphic.

Depending on driving style andsurface conditions the mostappropriate interval can vary.

For your safety

If you have to mount a kerb, doso slowly and, if possible, approachit with the wheels at right-angles tothe kerb. Avoid steep and sharpedged obstacles. Do not scrub thetyre sidewalls when parking.

Regularly examine the tyre surfacefor cuts, foreign bodies and unevenwear. An uneven tread wear patterncould indicate faulty wheelalignment.

Refer to page 178 for permissiblesnow chains.

Capacities and specifications

172

IDENTIFICATION NUMBERS

xxxx kg

Vehicle identification plate

The vehicle identification plate islocated on the lower section of theright-hand front door pillar.

Vehicle identification number

The number is located in the enginecompartment. It is additionallystamped onto a tag on the left-handside of the instrument panel.

Engine number

The engine number is located onthe engine block (seen in thedirection of travel):

• All engines – near gearbox onfront left-hand side facing theradiator.

FUEL

Use only high quality fuel withoutany supplemental additives or otherengine treatments.

Vehicles with a petrol engine

Use unleaded petrol according tospecification EN 228 or equivalentwith minimum 95 octane. Leadedfuel or fuel/additives containingother metallic compounds (e.g.manganese-based) may damage theemission system.

Vehicles with a diesel engine

Use diesel fuel according tospecification EN 590 or equivalent.

Do not mix it with any oil, petrol orother liquids.

Diesel fuels which contain a mix ofup to 5 % RME (bio diesel) areacceptable.

Prolonged use of supplementaladditives to prevent fuel waxing isnot recommended. Do not addkerosene, paraffin or petrol todiesel fuels.


173

Fuel consumption according to EC Directive 80/1268/EEC

Fuel consumption –litres/100 km

Tyre size Axleratio

Urbanenviron-

ment

Non-urban

environ-ment

Total

CO2emissions (g/km)

1.25 l Duratec (Stage III/Stage IV)

All 4.25 8.6 5.1 6.4 152

1.4 l Duratec (Stage III/Stage IV) Manual transmission

All 4.25 8.5 5.3 6.5 154

1.4 l Duratec (Stage IV) Durashift EST transmission

All 4.25 8.0 5.2 6.2 148

1.6 l Duratec (Stage III/Stage IV) Manual transmission

All 4.25 8.9 5.3 6.6 157

1.6 l Duratec (Stage IV) Automatic transmission

All −1 10.3 6.1 7.6 181

1.4 l Duratorq-TDCi (Stage III) Manual transmission

All 3.61 5.3 3.9 4.4 116

1.4 l Duratorq-TDCi (Stage IV) Manual transmission

All 3.61 5.7 4.0 4.6 122

1.4 l Duratorq-TDCi (Stage III) Durashift EST transmission

All 3.37 5.1 3.9 4.3 114

1.6 l Duratorq-TDCi (Stage III/Stage IV) Manual transmission

All 3.37 5.5 4.0 4.5 119

1 Data not available at the time of printing.


174

ENGINE OIL

Engine oil change

Use Ford/Motorcraft Formula ESAE 5W-30 engine oil.

Alternative engine oils with theviscosity SAE 5W-30 meeting therequirements of Ford SpecificationWSS-M2C913-B may also be used.

For petrol engines, engine oilmeeting the Ford specificationWSS-M2C913-A may also be used.

Engine oil top-up

If you are unable to find an oil thatmeets this specification, you mustuse an oil of the viscositySAE 5W-30, SAE 5W-40 orSAE 10W-40 according to ambienttemperatures, meeting therequirements of eitherACEA A1/B1 or ACEA A3/B3specifications. Use of these oils mayresult in longer cranking periods,reduced engine performance,reduced fuel economy andincreased emission levels.

VEHICLE FLUIDS

Part Recommended fluid Specification

Power assisted steering Ford Power Steering Fluid WSA-M2C 195-A

Coolant Motorcraft SuperPlus Antifreeze WSS-M97 B44-D

Capacities (litres)

Engine1.25 l

Duratec1.4 l

Duratec1.6 l

Duratec

1.4 lDuratorq-

TDCi

1.6 lDuratorq-

TDCi

Engine oil – with filter– without filter

3.751/3.802

3.503.751/3.802

3.504.102/4.253

3.753.803.40

3.853.45

Power assisted steering MAX mark

Cooling system including heating

5.0 5.5 6.0

Screen washer system 2.5

Fuel tank 45 43

1 With engine oil filter EFL 500




175

VEHICLE WEIGHT

Vehicle weight (kg)

1.25 l Duratec

EC base kerb weight 1157

Maximum payload 448

Permissible gross weight 1605

Permissible roof rack weight 25

1.4 l Duratec


Maximum payload 449



1.4 l Duratec Durashift EST transmission


Maximum payload 443



1.6 l Duratec without ESP


Maximum payload 446



1.6 l Duratec with ESP


Maximum payload 441



1.6 l Duratec Automatic transmission


Maximum payload 466




176

Vehicle weight (kg)

1.4 l Duratorq-TDCi without ESP


Maximum payload 483



1.4 l Duratorq-TDCi with ESP


Maximum payload 478



1.4 l Duratorq-TDCi Durashift EST transmission


Maximum payload 478



1.6 l Duratorq-TDCi without ESP


Maximum payload 510



1.6 l Duratorq-TDCi with ESP


Maximum payload 505




177

TYRE DATA

Tyre pressure

The pressure for your spare tyreshould be set to the highest valuegiven for your vehicle/tyre sizecombination.

Note: If the spare wheel rim or tiresize differs from the other wheelsfitted, see also section Spare

wheel, page 151 onwards.

When using winter tyres, the tyrepressures recommended by the tyremanufacturer should be adhered to.

Standard tyre pressures up to 160 km/h (cold tyres)

bar

Model Tyre size1 Normal loadup to 3 persons

Full load morethan 3 persons

Front Rear Front Rear

175/65 R 142 3.0 3.0 3.0 3.0

185/60 R 143 2.4 2.2 2.5 2.8

All 195/60 R 15 2.4 2.2 2.5 2.8All

195/55 R 16 2.4 2.2 2.5 2.8

T125/80 R 142 4.2 4.2 4.2 4.2

1 Summer tyres with various speed rating, depending on engine performance.

2 Spare wheel/Temporary spare wheel, maximum speed 80 km/h.

3 Winter tyres.

Comfort tyre pressures

Driving at comfort tyre pressureswill improve ride comfort, howeverit will alter the drivingcharacteristics and fuelconsumption of the vehicle.

For optimum dynamic performancestandard pressure settings arerecommended.

If the vehicle is used with aroof load, or is fully laden,

the tyres must be set to standardtyre pressure setting.

Comfort tyre pressures up to 160 km/h (cold tyres)

bar

Model Tyre sizeNormal load

up to 3 personsFull load morethan 3 persons


185/60 R 143 2.0 1.8 2.5 2.8

All 195/60 R 15 2.0 1.8 2.5 2.8

195/55 R 16 2.0 1.8 2.5 2.8

3 Winter tyres.


178

Tyre pressures for continuous road speed over 160 km/h(cold tyres)

bar

Model Tyre size1 Normal loadup to 3 persons

Full load morethan 3 persons


All195/60 R 15 2.4 2.2 2.5 2.8

All195/55 R 16 2.4 2.2 2.5 2.8

1 Summer tyres with various speed rating, depending on engine performance.

Snow chains

Use only the recommended smalllink snow chains on the drivingwheels (front).

Snow chains must only be fitted to14" x 5.5" J (47.5 offset) steelwheels with 185/60 R 14 wintertyres.

Do not exceed 50 km/h. Removethe chains immediately onsnow-free roads.

The ABS will continue to functionnormally.

Vehicles with Electronic StabilityProgram (ESP) may exhibit someunusual driving characteristicswhich can be avoided by switchingthe system off. Refer to the sectionElectronic Stability Program

(ESP), page 101.

In order to avoid damagingfull-diameter wheel covers, theyshould be removed before drivingwith snow chains.


179

DIMENSIONS

Dimensions mm

A = Maximum length 4013

B = Overall width (including exterior mirrors) 1950/19631

C = Overall height (EC kerb weight) 1512-1543

D = Wheelbase 2486

E = Track front 1477-1487

rear 1435-1445

1 Vehicles with electrically operated outside mirrors

ATTACHMENT POINTS FORTOWING EQUIPMENT


180

The installation of towingequipment should only be

performed by an expert.

Distances mm1

A = Bumper – end of towball 133

B = Attachment point – centre of towball 12

C = Wheel centre – centre of towball 869

D = Centre of towball – side member 493

E = Inner side of side member 986

F = Centre of towball – centre 1. attachment point 436

G = Centre of towball – centre 2. attachment point 721

1 All measurements refer to towing equipment officially released by Ford.


181

RADIO FREQUENCY REMOTE CONTROL

If the type approval of your remotecontrol is inspected, refer to thetable below.

It is recommended that you use theremote control only in the countrieslisted.

Type approval of the remote control

Country Official test number

1

433,92 MHz5WK4 725/8686/8071

BAKOM 97.0946.K.P.

MCW 129/95 23/1997

272/3-1998

542/98

Ref.No.: 3K43D/3R1B9/SPLS-RX9/98

1 Hereby, Siemens, declares that this remote control is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.


182

ENGINE IMMOBILISATION SYSTEM

If the type approval of your engine immobilisation system is inspected,refer to the table below.

Type approval of the engine immobilisation system


No label required

– 1

3043 104475A

M.C.W. 129/95 /(11)

– 1

No type approval necessary.

WT/122/98 II

ENG 3/2/RFS29

M.Ł. S.H. Nr. 003/2002

1 Data not available at the time of printing.


183

Type approval of the engine immobilisation system


LPREQ-0259-2002

171

B.61.TK.0.22.00.00/4940−2632

FCC ID:NT8-15607-PAT3XCVR

Index

184

A

ABS. See Brakes

Activity console. See Storage areas

Air conditioning. See Heating,ventilation and air conditioning

Airbag 87-92. . . . . . . . . . . . . . . . . . .

Airbag deactivation 91-92. . . . . . .

Airbag deactivation light 91-92. . .

Airbag warning light 91. . . . . . . . .

Curtain airbags 90. . . . . . . . . . . . . .

Front airbags 88. . . . . . . . . . . . . . .

Passenger airbag deactivation 91.

Side airbags 89. . . . . . . . . . . . . . . .

Anti-lock braking system (ABS).See Brakes

Anti-theft alarm system 76. . . . . . . .

Switch off the alarm 76. . . . . . . . .

Ashtray, Front ashtray 63. . . . . . . . .

Audio remote control. See Audiosystems

Audio systems

Audio remote control 58. . . . . . . .

Radio display 33. . . . . . . . . . . . . . .

A

Automatic transmission 107-114. . .

Cold mode 112. . . . . . . . . . . . . . . . .

Drive modes 111-114. . . . . . . . . . .

Emergency park position release 111. . . . . . . . . . . .

Gear display 107. . . . . . . . . . . . . . .

Kickdown 112. . . . . . . . . . . . . . . . .

Moving off 110. . . . . . . . . . . . . . . . .

Overdrive 109. . . . . . . . . . . . . . . . .

Parking 108. . . . . . . . . . . . . . . . . . .

Release button 107. . . . . . . . . . . . .

Selector lever lock 107, 111. . . . .

Selector lever positions 107-109. .

Starting the vehicle 105. . . . . . . . .

Stopping 110. . . . . . . . . . . . . . . . . .

Towing 160. . . . . . . . . . . . . . . . . . . .

Transmission/Engine systems faultwarning light 113-114. . . . . . . . . . .

Warning signal, audible 108. . . . . .

Auxiliary heater 45. . . . . . . . . . . . . .

Index

185

B

Battery 156. . . . . . . . . . . . . . . . . . . . .

Booster battery 157-158. . . . . . . .

Disconnected battery 156. . . . . . .

Ignition warning light 156. . . . . . .

Maintenance 156. . . . . . . . . . . . . . .

Remote control, battery replacing 72. . . . . . . . . . . .

Body paintwork preservation 162. .

Bonnet 164. . . . . . . . . . . . . . . . . . . . .

Brakes 98-100. . . . . . . . . . . . . . . . . .

ABS warning light 99. . . . . . . . . . .

Anti-lock braking system (ABS) 99. . . . . . . . . . . . . . . . . . . . .

Brake fluid reservoir 168. . . . . . . .

Brake system warning light 98-99

Disc brakes 98. . . . . . . . . . . . . . . . .

Dual circuit braking system 98. . .

Emergency Brake Assist 100. . . . .

Handbrake 100. . . . . . . . . . . . . . . .

Hazards on heavy breaking 100. . .

C

Capacities and specifications 172-183. . . . . . . . . . .

Central door locking. See Lockingsystem

Children

Child restraints 93-97. . . . . . . . . . .

Childproof safety locks 66. . . . . . .

Mass group categories 94. . . . . . . .

Placement of child seats 94-96. . .

Cigar lighter 63. . . . . . . . . . . . . . . . .

Clock, digital. See Digital clock

Clutch fluid, Clutch fluid reservoir 168. . . . . . . . .

C

Cooling system

Antifreeze 169. . . . . . . . . . . . . . . . .

Coolant 169. . . . . . . . . . . . . . . . . . .

Coolant capacity 174. . . . . . . . . . .

Temperature gauge 19. . . . . . . . . .

D

Date 9. . . . . . . . . . . . . . . . . . . . . . . . .

Digital clock 9, 20. . . . . . . . . . . . . . .

Dimensions 179-180. . . . . . . . . . . . .

Driving, Driving with a roof load 136. . . . . . .

Driving with a catalytic converter 126. . . . . . . . . . .

Durashift EST 115-121. . . . . . . . . . .

Downshift (Kickdown) 120. . . . . .

Driving on inclines 121. . . . . . . . . .

Gear display 116. . . . . . . . . . . . . . .

Parking 121. . . . . . . . . . . . . . . . . . .

Starting the engine 105. . . . . . . . .

Stopping 120. . . . . . . . . . . . . . . . . .

Towing 159. . . . . . . . . . . . . . . . . . . .

Transmission/Engine systems faultwarning light 121, 122. . . . . . . . . .

Warning signal, audible 120. . . . . .

Index

186

E

Electronic Stability Program (ESP) 101-102. . . . . . . . . . . . . . . . . .

Engine compartment 165-166. . . . .

Engine oil 167-168. . . . . . . . . . . . . .

Capacities 174. . . . . . . . . . . . . . . . .

Engine oil dipstick 167. . . . . . . . . .

Engine oil filler cap 168. . . . . . . . .

Oil pressure warning light 168. . . .

Oil specifications 174. . . . . . . . . . .

Engine speed limiter 103. . . . . . . . .

Engines

Bonnet 164. . . . . . . . . . . . . . . . . . . .

Compartment 165-166. . . . . . . . . .

Coolant 169. . . . . . . . . . . . . . . . . . .

Diesel engine, starting 104. . . . . . .

Diesel engine, switching off 104. .

Diesel low fuel safety mode 124. .

Disconnected battery 156. . . . . . .

Engine immobilisation system 73-75. . . . . . . . . . . . . . . . . .

Engine immobilisation system, type approval 182-183. . .

Engine number 172. . . . . . . . . . . . .

Engine warning light 123. . . . . . . .

Limited operation strategyprogramme 138. . . . . . . . . . . . . . . .

Oil 167-168, 174. . . . . . . . . . . . . . .

Petrol engine, flooded 103. . . . . . .

Petrol engine, starting 103. . . . . . .

Running in 13. . . . . . . . . . . . . . . . .

Environment protection 13. . . . . . .

F

Filling capacities 174. . . . . . . . . . . .

First aid kit 138. . . . . . . . . . . . . . . . .

Fog lights. See Lights

Front and rear screen, heated 45. .

Front screen, heated 45. . . . . . . . . .

Fuel 172. . . . . . . . . . . . . . . . . . . . . . .

Diesel fuel 172. . . . . . . . . . . . . . . . .

Diesel low fuel safety mode 124. .

Filling up 125. . . . . . . . . . . . . . . . . .

Fuel consumption 173. . . . . . . . . .

Fuel gauge 19. . . . . . . . . . . . . . . . .

Incorrect fuel 125. . . . . . . . . . . . . .

Low fuel level warning light 124. .

Petrol fuel 172. . . . . . . . . . . . . . . . .

Refuelling 124. . . . . . . . . . . . . . . . .

Specifications 172. . . . . . . . . . . . . .

Tank capacity 174. . . . . . . . . . . . . .

Unleaded 172. . . . . . . . . . . . . . . . . .

Fuel filler flap 125. . . . . . . . . . . . . . .

Fuel injection system shut-off switch 139. . . . . . . . . . . . .

Fuses 140-143. . . . . . . . . . . . . . . . . .

G

Gauges 19-21. . . . . . . . . . . . . . . . . . .

Glove compartment. See Storageareas

Index

187

H

Handbrake 100. . . . . . . . . . . . . . . . . .

Hazard flasher switch 138. . . . . . . .

Hazards on heavy braking 33. . . . . .

See also Brakes

Head restraints. See Seats

Heating, ventilation and airconditioning 36-44. . . . . . . . . . . . . .

Active carbon filter 36. . . . . . . . . .

Adjusting the temperature 38. . . .

Air conditioning 37, 40-41. . . . . . .

Air conditioning, maintenance 163. . . . . . . . . . . . . . .

Air distribution 38, 43. . . . . . . . . . .

Blower 38. . . . . . . . . . . . . . . . . . . . .

Controls 38. . . . . . . . . . . . . . . . . . . .

Defrosting the windows 39, 43. . .

Electronic automatic temperature control 41-43. . . . . .

Fresh air filter 36. . . . . . . . . . . . . .

General notes 37. . . . . . . . . . . . . . .

Rapid cooling 40. . . . . . . . . . . . . . .

Recirculated air 36, 40. . . . . . . . . .

Vents 36. . . . . . . . . . . . . . . . . . . . . .

Horn 54. . . . . . . . . . . . . . . . . . . . . . . .

I

Identification numbers 172. . . . . . .

Ignition switch 102. . . . . . . . . . . . . .

Immobilisation system 73-75. . . . . .

Coded keys 73. . . . . . . . . . . . . . . . .

Indicator lights. See Warning andindicator lights

Information messages 26-29. . . . . .

Instrument cluster 16-21. . . . . . . . .

Instrument panel 14-15. . . . . . . . . .

Interior lights. See Lights

J

Jack 153. . . . . . . . . . . . . . . . . . . . . . .

Jacking points 153-154. . . . . . . . . . .

Jump starting 157-158. . . . . . . . . . .

K

Keys. See Locking system

Index

188

L

Lights

Autolamps 46-47. . . . . . . . . . . . . . .

Bulb replacement 144-150. . . . . . .

Dipped beam 46, 52. . . . . . . . . . . .

Direction indicator lever 51. . . . . .

Direction indicator light 52. . . . . .

Exterior lights, audible warningsignal 46. . . . . . . . . . . . . . . . . . . . . .

Front fog lights 47-48. . . . . . . . . . .

Hazards on heavy braking 33, 51. .

Headlight flasher 52. . . . . . . . . . . .

Headlight levelling control 50. . . .

Headlights 46. . . . . . . . . . . . . . . . . .

Home safe lights 48-49. . . . . . . . . .

Interior lights 53. . . . . . . . . . . . . . .

Lane change indicators 33, 51. . . .

Light switch 46. . . . . . . . . . . . . . . .

Main beam 52. . . . . . . . . . . . . . . . .

Main beam indicator light 52. . . . .

Multifunction lever 51. . . . . . . . . .

Reading lights 53. . . . . . . . . . . . . . .

Rear fog light 48. . . . . . . . . . . . . . .

Side lights 46. . . . . . . . . . . . . . . . . .

Welcome lights 49. . . . . . . . . . . . . .

L

Locking system

Central door locking 68-72. . . . . .

Childproof safety locks 66. . . . . . .

Doors open warning light. See

Warning and indicator lights

Double locking 68-71. . . . . . . . . . .

Ignition switch 102. . . . . . . . . . . . .

Keys 64-65. . . . . . . . . . . . . . . . . . . .

Keys, coded for immobilisationsystem 73. . . . . . . . . . . . . . . . . . . . .

Locking the vehicle 70-71. . . . . . .

Locks 65-67. . . . . . . . . . . . . . . . . . .

Luggage compartment 66-67. . . .

Opening the bonnet 164. . . . . . . . .

Remote control 64-65. . . . . . . . . . .

Remote control, battery replacing 72. . . . . . . . . . . .

Remote control, programming 71-72. . . . . . . . . . . .

Remote control, type approval 181. . . . . . . . . . . . . .

Reprogramming the unlockingfunction 33. . . . . . . . . . . . . . . . . . . .

Steering lock 102. . . . . . . . . . . . . . .

Unlocking the vehicle 69. . . . . . . .

Luggage compartment

Closing the tailgate 67. . . . . . . . . .

Increasing load floor 81-82. . . . . .

Luggage cover 127. . . . . . . . . . . . .

Luggage net 128. . . . . . . . . . . . . . .

Opening the tailgate 66-67, 69. . .

Transporting luggage 126-127. . . .

Warning light, luggagecompartment 67. . . . . . . . . . . . . . .

Index

189

M

Maintenance chart 163. . . . . . . . . . .

Manual transmission 106. . . . . . . . .

Map pockets. See Storage areas

Message Centre 20-21, 22-35. . . . .

Average fuel consumption 25. . . .

Average speed 25. . . . . . . . . . . . . .

Chime deactivation 34. . . . . . . . . .

Controls 22. . . . . . . . . . . . . . . . . . . .

Display warning light 26-29. . . . . .

Distance to empty 25. . . . . . . . . . .

Fuel economy 25. . . . . . . . . . . . . . .

Main menu overview 24. . . . . . . . .

Measure units 35. . . . . . . . . . . . . . .

Odometer 25. . . . . . . . . . . . . . . . . .

Outside temperature 25. . . . . . . . .

Setting the language 34-35. . . . . .

Settings menu 31-35. . . . . . . . . . .

Settings menu overview 32. . . . . .

Time setting 30. . . . . . . . . . . . . . . .

Tripmeter 25. . . . . . . . . . . . . . . . . .

Warning/information messages 26-29. . . . . . . . . . . . . . . .

Mirrors

Interior rear-view mirror 59. . . . . .

Outside rear-view mirrors,electrically operated 60. . . . . . . . .

Outside rear-view mirrors, convex 59. . . . . . . . . . . . . . . . . . . . .

Outside rear-view mirrors, folding 59, 60. . . . . . . . . . . . . . . . . .

Outside rear-view mirrors, heated 60. . . . . . . . . . . . . . . . . . . . .

Outside rear-view mirrors,manually 59. . . . . . . . . . . . . . . . . . .

M

Multifunction display 20-21. . . . . . .

Multifunction lever. See Lights

O

Odometer 21, 25. . . . . . . . . . . . . . . .

Oil types 174. . . . . . . . . . . . . . . . . . .

P

Paint chip repair 162. . . . . . . . . . . . .

Parking 126. . . . . . . . . . . . . . . . . . . .

Automatic transmission 108. . . . .

Durashift EST 121. . . . . . . . . . . . . .

Handbrake 100. . . . . . . . . . . . . . . .

Parking on a hill 100. . . . . . . . . . . .

Ultrasonic park distance sensor 137. . . . . . . . . . . . . . . . . . . .

Power point 63. . . . . . . . . . . . . . . . . .

Power windows. See Powerwindows

Preface 12. . . . . . . . . . . . . . . . . . . . .

R

Radio frequency remote control,type approval 181. . . . . . . . . . . . . . .

Rear screen, heated 45. . . . . . . . . . .

Refill capacities 174. . . . . . . . . . . . .

Reverse gear wipe. See Screenwashing/wiping

Roof rack 136. . . . . . . . . . . . . . . . . . .

Index

190

S

Screen washing/wiping

Autowipers 55-56. . . . . . . . . . . . . .

Front screen wiping 55-56. . . . . . .

Intermittent wipe interval 55. . . . .

Rear screen washing/wiping 57. . .

Reverse gear wipe 57. . . . . . . . . . .

Washer 57. . . . . . . . . . . . . . . . . . . . .

Washer fluid capacity 174. . . . . . .

Washer fluid reservoir 170. . . . . . .

Washer jets 170. . . . . . . . . . . . . . . .

Wiper blades 171. . . . . . . . . . . . . . .

Wiper lever 55-57. . . . . . . . . . . . . .

Seat belts 82-86. . . . . . . . . . . . . . . . .

Adjusting the height 83. . . . . . . . .

Care of seat belts 86. . . . . . . . . . . .

Pregnant women 84. . . . . . . . . . . .

Seat belt pretensioner 85. . . . . . . .

Seat belt pretensioner warninglight 91. . . . . . . . . . . . . . . . . . . . . . .

Seats 77-82. . . . . . . . . . . . . . . . . . . .

Armrest 78. . . . . . . . . . . . . . . . . . . .

Child restraints 93-97. . . . . . . . . . .

Correct position 77. . . . . . . . . . . . .

Fold flat front passenger seat 79. .

Folding the rear seatback forwards 81. . . . . . . . . . .

Folding the seat cushion andseatback forwards 4, 82. . . . . . . . .

Head restraints 80. . . . . . . . . . . . . .

Heated front seats 79-80. . . . . . . .

Mass group categories 94. . . . . . . .

Seat covers 77, 90. . . . . . . . . . . . . .

S

Servicing 163-171. . . . . . . . . . . . . . .

Socket/cigar lighter 63. . . . . . . . . . .

Speedometer 19. . . . . . . . . . . . . . . . .

Starting the engine 103-104. . . . . .

Starting, general points 103. . . . . . .

Steering

Adjusting the steering wheel 54. .

Power steering fluid level 170. . . .

Steering lock 102. . . . . . . . . . . . . . .

Storage areas

Activity console 131-132. . . . . . . .

Card holder 2, 129. . . . . . . . . . . . . .

Coin holder 2, 129, 130. . . . . . . . .

Front storage compartment 2, 128. . . . . . . . . . . .

Glove compartment 2, 129. . . . . . .

Map pockets 4, 130. . . . . . . . . . . . .

Pencil clip 2, 129. . . . . . . . . . . . . . .

Storage area passenger side 128. .

Storage compartment 2, 128. . . . .

Storage pockets 3, 130. . . . . . . . . .

Under-seat storage 3, 129. . . . . . . .

Storage pockets. See Storage areas

Sun visors 62. . . . . . . . . . . . . . . . . . .

Sunroof 62. . . . . . . . . . . . . . . . . . . . .

Index

191

T

Tachometer 19. . . . . . . . . . . . . . . . . .

Towing

Attachment points 180. . . . . . . . . .

Pushing/towing 158-160. . . . . . . . .

Starting by towing or pushing 160

Towing eye 153, 158-159. . . . . . . .

Trailer

Tow bar 133-136. . . . . . . . . . . . . . .

Trailer coupling, removable 133-136. . . . . . . . . . . . .

Trailer towing 133. . . . . . . . . . . . . . .

Steep gradients 133. . . . . . . . . . . .

Tripmeter 21, 25. . . . . . . . . . . . . . . .

Tyres and wheels

Changing a wheel 151-156. . . . . . .

Directional tyres 151. . . . . . . . . . .

Fitting a wheel 155-156. . . . . . . . .

Jacking up 153-155. . . . . . . . . . . . .

Removing a wheel 154-155. . . . . .

Snow chains 178. . . . . . . . . . . . . . .

Spare wheel 151-152. . . . . . . . . . .

Tyre data 177-178. . . . . . . . . . . . . .

Tyre information 171. . . . . . . . . . .

Tyre pressure 177-178. . . . . . . . . .

U

Under-seat storage. See Storageareas

V

Vehicle care 161. . . . . . . . . . . . . . . .

Vehicle fluids 174. . . . . . . . . . . . . . .

Capacities 174. . . . . . . . . . . . . . . . .

Specification 174. . . . . . . . . . . . . . .

Vehicle identification number 172. .

Vehicle identification plate 172. . . .

Vehicle weight 175-176. . . . . . . . . .

Ventilation. See Heating, ventilationand air conditioning

Index

192

W

Warning and indicator lights

ABS warning light 99. . . . . . . . . . .

Airbag deactivation light 91-92. . .

Airbag/seat belt pretensionerwarning light 91. . . . . . . . . . . . . . . .

Brake system warning light 98, 99, 168. . . . . . . .

Direction indicator light 52. . . . . .

Doors open warning light 67. . . . .

Electronic Stability Program(ESP) indicator light 101-102. . . .

Engine warning light 123. . . . . . . .

Front fog light indicator light 47-48. . . . . . . . . . . .

Frost warning 124. . . . . . . . . . . . . .

Glow plug indicator light 104. . . . .

Ignition warning light 156. . . . . . .

Low fuel level warning light 124. .

Main beam indicator light 52. . . . .

Oil pressure warning light 168. . . .

Overdrive indicator light 109. . . . .

Power steering 123. . . . . . . . . . . . .

Rear fog light indicator light 48. . .

Transmission/Engine systems faultwarning light 113-114, 121, 122. . .

W

Warning lights. See Warning andindicator lights

Warning messages 26-29. . . . . . . . .

Warning signal, audible

Automatic transmission 108. . . . .

Chime deactivation 34. . . . . . . . . .

Durashift EST 120. . . . . . . . . . . . . .

Exterior lights 46. . . . . . . . . . . . . .

Low fuel level 124. . . . . . . . . . . . . .

Message Centre, confirmationchime 22. . . . . . . . . . . . . . . . . . . . . .

Ultrasonic park distance sensor 137. . . . . . . . . . . .

Warning symbols 13. . . . . . . . . . . . .

Warning triangle 138. . . . . . . . . . . . .

Warranty 162. . . . . . . . . . . . . . . . . . .

Washing the vehicle 161. . . . . . . . . .

Weights 175-176. . . . . . . . . . . . . . . .

Wheels. See Tyres and wheels

Wiper lever. See Screenwashing/wiping

manual fusion

Documents