material safety data sheet - signagensignagen.com/datasheet/sl100324 msds.pdf · 100324 sl100324...
TRANSCRIPT
Conforms to 93/112/EC and ISO 11014-1
Material Safety Data Sheet
BlotFreshTM Western Blot Stripping Reagent
100324
SL100324
CALL CHEMTREC:800.424.9300 3/21/2006
3/21/2006
Product name
Suppliernufacturer
Product No.
MSDS#Validation Date
Print DateIn Case of Emergency
Section 1. Chemical Product and Company IdentificationResponsible Name SignaGen Laboratories
Intended Use Refer to the instruction booklet for proper and intended use. Otherwise, contact supplier for specific applications.
Eng
1) Ingredient Name #1 2-7 -- Xi R362) Ingredient Name #2 0.5-1 -- C R343) Ingredient Name #3 1-6 -- C R34
Ingredient Name EC NumberCAS No. R-Phrases
Substance/Preparation Preparation
% Symbol
:
Section 2. Composition, Information on Ingredients
Physical/chemical hazardsHuman health hazardsEnvironmental hazards Not applicable.
Irritating to eyes, respiratory system and skin.Not applicable.
Eye contact. Ingestion.
Emergency Overview
Medical Conditions Aggravated byOverexposure:
Repeated or prolonged exposure is not known to aggravate medical condition.
Not available.Overexposure /Signs/Symptoms
Section 3. Hazards Identification
Routes of Entry
Potential Acute Health Effects
Carcinogenic Effects Data
See Toxicological Information (section 11)
Avoid contact with eyes, skin and clothing. Avoid breathing vapor or mist. Keep container closed. Use with adequate ventilation.Wash thoroughly after handling.
Hazardous in case of skin contact (irritant), of eye contact (irritant), of inhalation (lung irritant). Slightly hazardous in case ofskin contact (corrosive, permeator), of eye contact (corrosive), of ingestion, of inhalation (lung corrosive).CARCINOGENIC EFFECTS: Classified 3 (Not classifiable for human.) by IARC [Ingredient Name #2].MUTAGENIC EFFECTS: Not available.TERATOGENIC EFFECTS: Not available.
Review the most current and approved institutional guideline, protocol, standard operating procedure(s) and MSDS(s)for the proper handling of institutional materials/equipment associated with the use of this product.WARNING!CONTAINS MATERIAL WHICH CAUSES DAMAGE TO THE FOLLOWING ORGANS: LUNGS,RESPIRATORY TRACT, SKIN, EYES, EYE, LENS OR CORNEA.MAY CAUSE RESPIRATORY TRACT, EYE AND SKIN IRRITATION.
Classification R36/37/38
United States
Europe
Continued on Next Page
BlotFreshTM Western Blot Stripping Reagent Page: 2/6
Do NOT induce vomiting unless directed to do so by medical personnel. Never give anything by mouth to an unconsciousperson. Loosen tight clothing such as a collar, tie, belt or waistband. Get medical attention if symptoms appear.
Skin Contact
Ingestion
Check for and remove any contact lenses. In case of contact, immediately flush eyes with plenty of water for at least 15minutes. Cold water may be used. Get medical attention.
In case of contact, immediately flush skin with plenty of water. Cover the irritated skin with an emollient. Removecontaminated clothing and shoes. Cold water may be used.Wash clothing before reuse. Thoroughly clean shoes beforereuse. Get medical attention.
Hazardous in case of inhalation (lung irritant). Slightly hazardous in case of inhalation (lung corrosive).Slightly hazardous in case of ingestion.Sensitization of the product: Not available.Hazardous in case of skin contact (irritant). Slightly hazardous in case of skin contact (corrosive, permeator). Skininflammation is characterized by itching, scaling, reddening, or, occasionally, blistering.
Skin Contact
Hazardous in case of eye contact (irritant). Slightly hazardous in case of eye contact (corrosive).Eye Contact
Inhalation
Aggravating conditions Repeated or prolonged exposure is not known to aggravate medical condition.
First-Aid Measures
If inhaled, remove to fresh air. If not breathing, give artificial respiration. If breathing is difficult, give oxygen. Get medicalattention.
Notes to Physician Not available.Not available.Protection of first-aiders
Ingestion
Effects and symptoms
Inhalation
Eye Contact
Section 4. First Aid Measures
Notice to Reader Get immediate medical attention.
Hazardous thermal (de)compositionproducts
Not applicable.
Non-flammable.
Not applicable.
Not applicable.
Not applicable.
Section 5. Fire Fighting Measures
Flammability of the Product
Flash Points
Fire Hazards in Presence of VariousSubstances
Fire Fighting Mediaand Instructions
Not applicable.Protective Clothing (Fire)
Absorb with an inert material and put the spilled material in an appropriate waste disposal. Neutralize the residue witha dilute solution of sodium carbonate. Finish cleaning by spreading water on the contaminated surface and allow toevacuate through the sanitary system. Be careful that the product is not present at a concentration level above TLV.Check TLV on the MSDS and with local authorities.
Section 6. Accidental Release Measures
Small Spill and Leak Dilute with water and mop up, or absorb with an inert dry material and place in an appropriate waste disposal container.If necessary: Neutralize the residue with a dilute solution of sodium carbonate. Finish cleaning by spreading wateron the contaminated surface and dispose of according to local and regional authority requirements.
Environmental Precautions andClean-up Methods
Personal precautions Splash goggles. Lab coat. Vapor respirator. Be sure to use an approved/certified respirator or equivalent. Gloves.
Keep container tightly closed. Keep container in a cool, well-ventilated area.
Avoid contact with eyes, skin, and clothing. Avoid breathing vapors or spray mists. Keep container closed. Use withadequate ventilation. Wash thoroughly after handling.
Section 7. Handling and Storage
Handling
Storage
Intended Use Refer to the instruction booklet for proper and intended use. Otherwise, contact supplier for specific applications.
Continued on Next Page
BlotFreshTM Western Blot Stripping Reagent Page: 3/6
Suitable / Not suitablePackaging materials
Use original container.
1) Ingredient Name #1 Not available.2) Ingredient Name #2 TWA: 8 CEIL: 8 (mg/m3) from BAuA [Germany] [1999] Inhalation3) Ingredient Name #3 Not available.
Germany
1) Ingredient Name #1 Not available.2) Ingredient Name #2 Not available.3) Ingredient Name #3 Not available.
Netherlands
1) Ingredient Name #1 Not available.2) Ingredient Name #2 STEL: 5 (ppm) from INRS [France] [1999] Inhalation3) Ingredient Name #3 Not available.
France
1) Ingredient Name #1 Not available.2) Ingredient Name #2 CEIL: 5 (ppm) from Arbeidstilsynet [Norway] [1996] Inhalation3) Ingredient Name #3 Not available.
Norway
1) Ingredient Name #1 Not available.2) Ingredient Name #2 CEIL: 5 (ppm) from Arbejdstilsynet [Denmark] [1996] Inhalation3) Ingredient Name #3 Not available.
Denmark
1) Ingredient Name #1 Not available.2) Ingredient Name #2 STEL: 5 (ppm) from AFS [Sweden] [1996] Inhalation3) Ingredient Name #3 Not available.
Sweden
1) Ingredient Name #1 Not available.2) Ingredient Name #3 Not available.
United States
Ingredient Name Occupational Exposure Limits
Engineering Controls Provide exhaust ventilation or other engineering controls to keep the airborne concentrations of vapors below theirrespective threshold limit value.
Section 8. Exposure Controls/Personal Protection
Exposure Limit Values
Personal ProtectionEyesBody
Hands
Protective Clothing(Pictograms)
Gloves.Lab coat.Splash goggles.
Respiratory Respirator is not needed under normal and intended conditions of use, if exposures are kept below established limits.
The lowest known value is 100°C (212°F) (Milli-Q Water).
Liquid.
2.8 [Acidic.]
May start to solidify at -0.1°C (31.8°F) based on data for: Milli-Q Water.
Not applicable.
Not available.
Not available.
Clear (Light.)
Boiling/Condensation Point
Melting/Freezing Point
Physical State andAppearance
Molecular Weight
pH (1% Soln/Water)
Odor
Taste
Color
Section 9. Physical and Chemical Properties
Continued on Next Page
BlotFreshTM Western Blot Stripping Reagent Page: 4/6
1 (Water = 1)
The highest known value is 0.62 (Air = 1) (Milli-Q Water).
The highest known value is 2.3 kPa (@ 20°C) (Milli-Q Water).
See solubility in water, methanol.
Easily soluble in cold water.Soluble in methanol.Partially soluble in hot water.Insoluble in diethyl ether.
0.36 (Milli-Q Water) compared to Butyl acetate.
Specific Gravity
Vapor Pressure
Vapor Density
Evaporation Rate
Dispersion Properties
Solubility
The product is stable.
Slightly reactive to reactive with oxidizing agents, organic materials, metals, alkalis.
Will not occur.
Not available.
Section 10. Stability and Reactivity
Stability and Reactivity
Conditions to avoid
Materials to avoid
Hazardous Polymerization
Hazardous DecompositionProducts
Not applicable.
Acute oral toxicity (LD50): 3500 mg/kg [Rat]. (Ingredient Name #3).Acute dermal toxicity (LD50): >3000 mg/kg [Rabbit]. (Ingredient Name #3).
Hazardous in case of eye contact (irritant), of inhalation (lung irritant).Slightly hazardous in case of ingestion, .
CARCINOGENIC EFFECTS: Classified 3 (Not classifiable for human.) by IARC [Ingredient Name #2].
Not available.
To the best of our knowledge, the toxicological properties of this product have not been thoroughly investigated. (IngredientName #3)
Not available.
Section 11. Toxicological Information
Toxicity to Animals
Chronic Effects on Humans
Other Toxic Effects on Humans
Special Remarks on Toxicity toAnimals
Special Remarks on ChronicEffects on Humans
Special Remarks on Other ToxicEffects on Humans
Ecotoxicity Not available.
Mobility
Germany water class
Not available.
Not available.
Not available.
Persistence/degradability
Bioaccumulative potential
VCI WGK: No products were found.
Section 12. Ecological Information
Waste must be disposed of in accordance with federal, state and local environmental control regulations.
Not available.
Waste Information
Waste Stream
Section 13. Disposal Considerations
Consult your local or regional authorities.
Continued on Next Page
BlotFreshTM Western Blot Stripping Reagent Page: 5/6
Contact the supplier for all information regarding the proper transportation method for this material.
Section 14. Transport Information
U.S. Federal Regulations
Pennsylvania RTK: Ingredient Name #2: (environmental hazard, generic environmental hazard)Massachusetts RTK: Ingredient Name #2New Jersey: Ingredient Name #2
Irritating substance.Target organ effects.
HCS Classification
Section 15. Regulatory Information
California prop. 65: No products were found.
TSCA 8(b) inventory: Ingredient Name #1; Ingredient Name #2; Milli-Q WaterTSCA 8(d) H and S data reporting: Ingredient Name #2
Clean Water Act (CWA) 307: No products were found.
Clean Water Act (CWA) 311: Ingredient Name #2
Clean air act (CAA) 112 accidental release prevention: Ingredient Name #2
Clean air act (CAA) 112 regulated flammable substances: No products were found.
Clean air act (CAA) 112 regulated toxic substances: Ingredient Name #2
State Regulations
CEPA DSL: Ingredient Name #1; Ingredient Name #2; Milli-Q Water
Australia (NICNAS): Ingredient Name #1; Ingredient Name #2; Milli-Q Water
VCI WGK: No products were found.
Korea (TCCL): Ingredient Name #1; Ingredient Name #2; Milli-Q Water
Philippines (RA6969): Ingredient Name #1; Ingredient Name #2; Milli-Q Water
WHMIS (Canada) CLASS D-2A: Material causing other toxic effects (VERY TOXIC).
R36/37/38- Irritating to eyes, respiratory system and skin.DSCL (EEC)
International Regulations
Not available.EINECS
International Lists
SARA 302/304/311/312 extremely hazardous substances: Ingredient Name #2SARA 302/304 emergency planning and notification: Ingredient Name #2SARA 302/304/311/312 hazardous chemicals: Ingredient Name #2SARA 311/312 MSDS distribution - chemical inventory - hazard identification: Ingredient Name #2: immediate health hazard, delayed health hazard
R36/37/38- Irritating to eyes, respiratory system and skin.
S2- Keep out of the reach of children.S46- If swallowed, seek medical advice immediately and show this container or label.
Irritant
Label Requirements(Europe)
1
Continued on Next Page
BlotFreshTM Western Blot Stripping Reagent Page: 6/6
Version 1
Date of Previous Issue No PreviousValidation
Not available.
Section 16. Other Information
References
Validated by SignaGen Administration on 3/21/2006 Verified by SignaGen Administration.
Printed 3/21/2006Notice to ReaderTo the best of our knowledge, the information contained herein is accurate. However, neither the above named supplier nor any of its subsidiaries assumes anyliability whatsoever for the accuracy or completeness of the information contained herein.Final determination of suitability of any material is the sole responsibility of the user. All materials may present unknown hazards and should be used with caution.Although certain hazards are described herein, we cannot guarantee that these are the only hazards that exist.
Hazardous MaterialInformation System
(U.S.A.)
101h
10
1
* National Fire ProtectionAssociation (U.S.A.)
Health
Specific Hazard
Reactivity
Fire HazardHealth
Fire Hazard
Reactivity
Personal Protection
History of Document Changes Any information changes since last document version are marked with a triangle symbol.Irritating to eyes.Causes burns.Causes burns.
Full text of R-Phrasesreferenced under headings 2 and 3:
Intended Use Refer to the instruction booklet for proper and intended use. Otherwise, contact supplier for specific applications.