MATERIAL SAFETYDATA SHEET

One ShoFM Gun Cleanerand Dry Lube

MSDS REV. DATE: 11/10/09

SECTION 1: PRODUCT AND COMPANY IDENTIFICATION

PRODUCT NAME: Hornady One ShoFM Gun Cleaner and Dry Lube

TRADE NAMES: Hornady One ShoFM Case LubeSYNONYMS: Gun cleaner, Dynaglide, One Shot, Dry lubePART NUMBERS: 9990

MANUFACTURERI DISTRIBUTOR: Hornady Manufacturing CompanyADDRESS: 3625 W. Old Potash Hwy

Grand Island, NE 68803

PRODUCT USE: Cleanerllubricant for firearms and other metal products.PREPARED BY: M. Spencer

EMERGENCY PHONE: 800-338-3220CHEMTREC PHONE: 800-424-9300 CHEMTREC INTERNATIONAL: +703-527-3887OTHER CALLS: (308) 382-1390

SECTION 2: COMPOSITIONIINFORMATION ON INGREDIENTS

HAZARDOUS INGREDIENTS:

NAME

Aliphatic HydrocarbonProprietary WaxesProprietary WaxesHydrocarbon Propellant

CAS#110-54-3

N/AN/A

68476-86-8

O/OWT93.631.5N/A

313YesN/AN/AN/A

OSHA PELTWA(ppm)

500N/AN/A800

ACGIH TLVTWA(ppm)

50.00N/AN/A

800

SECTION 2 NOTES:

SECTION 3: HAZARDS IDENTIFICATION

EMERGENCY OVERVIEW: Do not take internally. Flammable, keep away from sources of ignition. Symptoms of overexposure includegastrointestinal irritation, respiratory tract irritation, central nervous system depression (dizziness, drowsiness, weakness, fatigue, nausea,headache, unconsciousness), numbness of extremities. Causes mild to moderate eye irritation. Defats the skin.

ROUTES OF ENTRY: Inhalation, ingestion, eyes, skin absorption.

POTENTIAL HEALTH EFFECTS

EYES: May cause mild irritation. Symptoms may include stinging, tearing and redness.

SKIN: Low order of toxicity. Frequent or prolonged contact may irritate and cause dermatitis. Skin contact may aggravate and existingdermatitis condition.

INGESTION: Single dose oral toxicity is low. May cause abdominal pain and gastrointestinal irritation. Material that enters lungs duringswallowing or vomiting may cause lung irritation and/or lung damage.

INHALATION: Breathing small amounts of vapors during normal use is not likely to cause harmful effects; breathing large amounts maybe harmful. Symptoms, such as lung irritation and nerve damage or possibly even death may be seen following repeatedor prolonged exposure to concentrations exceeding the recommended exposure limits (see section 1).

ACUTE HEALTH HAZARDS: Irritation (eyes, skin, respiratory tract), gastrointestinal irritation, reversible liver effects, mild reversible kidneyeffects, nasal damage, chemical pneumonitis.

CHRONIC HEALTH HAZARDS: Central nervous system damage

MEDICALCONDITIONSGENERALLYAGGRAVATEDBYEXPOSURE:Conditionsthat afflict the following organs may be aggravated byexposure to this product: Lungs, kidneys, liver, skin.

PAGE 1 OF 5

MATERIAL SAFETYDATA SHEET

One ShOPM Gun Cleaner

and Dry Lube

MSDS REV. DATE: 11/10/09

CARCINOGENICITYOSHA: No IARC: NoOTHER: See section 15

SECTION 3 NOTES: Health studies have shown that many hydrocarbons pose potential human health risks which may vary from person toperson. As a precaution, exposure to liquids, vapors mists or fumes should be minimized.

SECTION 4: FIRST AID MEASURES

EYES: Immediately flush out fume or particles with large amounts of water for at least 15 minutes. If irritation develops, or if there is anyvisual distortion, call physician.

SKIN: Wash affected skin thoroughly with soap and water. Remove grossly contaminated clothing, including shoes. If symptoms persist,seek medical attention.

INGESTION: Do not induce vomiting; this material is an aspiration hazard. If victim is drowsy or unconscious, place on left side with the headdown. Keep victim at rest and seek medical attention. If possible, do not leave individual unattended.

INHALATION: If symptoms develop, move individual away from exposure and into fresh air. If symptoms persist, seek medical attention.Perform CPR if breathing stops.

SECTION 4 NOTES: Inhalation of high concentrations of this material, as could occur in enclosed spaces or during deliberate abuse may beassociated with cardiac arrhythmia's. Sympathomimetic drugs may initiate cardiac arrhythmia's in persons exposed to this material.

SECTION 5: FIRE-FIGHTING MEASURES

FLAMMABLE LIMITS IN AIR, UPPER: N/A(% BY VOLUME) LOWER: N/A

FLASH POINT:F: Level 3 AerosolC:

METHOD USED: TCC

EXPLOSIVE LIMIT:Lower: 1.1Upper: 7.5

HMIS HAZARD CLASSIFICATIONHEALTH: 2 FLAMMABILITY: 3OTHER:

Physical: 0

EXTINGUISHING MEDIA: Regular foam, carbon dioxide or dry chemical.

SPECIAL FIRE FIGHTING PROCEDURES: Water may be ineffective in fighting fires involving this product; however water may be used tokeep surrounding containers cool. Wear SCBA with full face piece operated in the positive pressure demand mode with appropriate turn-outgear and chemical resistant personal protective equipment.

UNUSUAL FIRE AND EXPLOSION HAZARDS: Material is highly volatile and gives off vapors which may travel along the ground or bemoved by ventilation and ignited by pilot lights, other flames, sparks, heaters, smoking, electric motors, static discharge, or other ignitionsources at locations distant from material handling point. Never use welding or cutting torch on or near container (even empty) becauseproduct or residue may ignite explosively.

HAZARDOUS DECOMPOSITION PRODUCTS: Carbon monoxide, carbon dioxide and various hydrocarbons.

SECTION 5 NOTES:

PAGE 2 OF 5

MATERIAL SAFETYDATA SHEET

One ShotTM Gun Cleanerand Dry Lube

MSDS REV. DATE: 11/10/09

SECTION 6: ACCIDENTAL RELEASE MEASURES

ACCIDENTAL RELEASE MEASURES:

Small Spill: Absorb liquid on vermiculite, floor absorbent or other absorbent material.Large Spill: Eliminate all ignition sources (flares, flames including pilot lights, electric sparks). Persons not wearing PPE should be

excluded from area of spill until cleanup has been completed. Stop spill at source. Prevent from entering drains. sewers, streams or otherbodies of water. Prevent from spreading. Cover sewer grates and dike the spill. If runoff occurs, notify authorities as required. Pump orvacuum transfer spilled product to clean containers for recovery. Absorb unrecoverable product. Transfer contaminated absorbent, soil andother materials to approved containers for disposal.

SECTION 6 NOTES:

SECTION 7: HANDLING AND STORAGE

HANDLING AND STORAGE: Containers of this material may be hazardous when empty. Since emptied containers retain product residue(vapor, liquid and/or solid), all hazard precautions given in the data sheet must be observed.

Hydrocarbon solvents are basically non-conductors of electricity and can become electro statically charged during mixing, filtering or pumpingat high flow rates. If this charge reaches sufficiently high level, sparks can form that may ignite the vapors of flammable liquids.

WARNING

Sudden release of hot organic chemical vapors or mists from process equipment operating at elevated temperature and pressure, or suddenincrease of air into vacuum equipment, may result in ignitions without the presence of obvious ignition sources. Published "auto ignition" or"ignition" temperature values cannot be treated as safe operating temperature in chemical processes without analysis of the actual processconditions. Any use of this product in elevated temperature processes or locations should be thoroughly evaluated to establish and maintainsafe operating conditions.

SECTION 7 NOTES: Refer to section 10 for firefighting equipment and procedures, and section 10 for reactivity information.

SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION

ENGINEERING CONTROLS: Provide room ventilation as needed to maintain exposures below PEL.

VENTILATION: Use sufficient mechanical (general exhaust) if needed to maintain exposure levels below PEL. This may be especiallynecessary when product is used in a confined area or is heated above ambient temperatures.

RESPIRATORY PROTECTION: Not generally needed for normal product use. If levels cannot be maintained below PEL, a NIOSH approvedorganic vapor or supplied air respirator will be required.

EYE PROTECTION: Safety glasses with side shields are recommended.

SKIN PROTECTION: Chemical resistant gloves are recommended if skin irritation develops, or to prevent prolonged exposure.

OTHER PROTECTIVE CLOTHING OR EQUIPMENT:

WORK HYGIENIC PRACTICES: Because the use of this product is generally associated with handling firearm cartridges and/or components,always wash hands thoroughly after use and before eating, drinking or using tobacco to reduce exposure to lead and other products of firearmdischarge.

SECTION 8 NOTES:

SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES

APPEARANCE: Solvent Lubricant

ODOR: Hydrocarbon odor.

PHYSICALSTATE: Liquid homogeneous mixture.

PAGE 3 OF 5

MATERIAL SAFETYDATA SHEET ornady

One ShotTMGun Cleanerand Dry Lube

MSDS REV. DATE: 11/10/09

pH AS SUPPLIED: N/ApH (Other): N/ABOILING POINT: Not DeterminedMELTING POINT: N/AFREEZING POINT: N/AVAPOR PRESSURE (mmHg): <75 psi @ 65° FVAPOR DENSITY (AIR = 1): Not DeterminedSPECIFIC GRAVITY (H2O = 1): .675@60°FEVAPORATION RATE: 9.00 (n-Butyl Acetate)SOLUBILITY IN WATER: NILPERCENT SOLIDS BY WEIGHT: N/APERCENT VOLATILE: Not DeterminedVOLATILE ORGANIC COMPOUNDS (VOC): n-HexaneMOLECULAR WEIGHT: N/A, MixtureVISCOSITY: N/ASECTION 9 NOTES:

SECTION 10: STABILITY AND REACTIVITY

STABILITY: Stable under normal conditions.

CONDITIONS TO AVOID (STABILITY): Extreme heat (over 130°F), contact with ignition sources.

INCOMPATIBILITY (MATERIAL TO AVOID): Strong oxidizing agents.

HAZARDOUS DECOMPOSITION OR BY-PRODUCTS: May form carbon dioxide and carbon monoxide as well as various hydrocarbons.

HAZARDOUS POLYMERIZATION: Will not occur

SECTION 11: TOXICOLOGICAL INFORMATION

TOXICOLOGICAL INFORMATION:

LD-50 (oral)

1100 ppm

SECTION 12: ECOLOGICAL INFORMATION

ECOLOGICAL INFORMATION: This product has no ecological information available. Individual component information is as follows:Hexane: Toxic to aquatic organisms.

TestType: EC50 DaphniaSpecies: Daphnia magnaTime: 48 h

Value: 3,878 mg/I

Test Type: EC50 AlgaeSpecies: Chlorella vulgarisTime: 3 h

Value: 12,840 mg/I

Test Type: EC50 AlgaeSpecies: SKELETOMATime:8hValue: 0.3 mg/I

PAGE40F 5

MATERIAL SAFETYDATA SHEET

One ShOPM Gun Cleanerand Dry Lube

~DedfJ.Dep~

MSDS REV. DATE: 11/10/09

SECTION 13: DISPOSAL CONSIDERATIONS

WASTE DISPOSAL METHOD: Product that has become waste may be considered hazardous and must disposed of accordingly. The userof this product is responsible for correctly classifying waste and seeing that it is disposed of in accordance with all federal, state and local laws.

RCRA HAZARD CLASS: D003

SECTION 14: TRANSPORT INFORMATION

U.S. DEPARTMENT OF TRANSPORTATIONPROPER SHIPPING NAME: Aerosols, flammable (each not exceeding 1L capacity)HAZARD CLASS: 2.1ID NUMBER: UN1950PACKING GROUP: IILABEL STATEMENT: Flammable Gas

SECTION 14 NOTES: May be marked and shipped ORM-D (domestic ground) per 49 CFR 173.306{a){3). For export of aerosols by vessel(IMDG) use UN1950, Limited Quantities (chapter 3.4).

SECTION 15: REGULATORY INFORMATION

U.S. FEDERAL REGULATIONSTSCA (TOXIC SUBSTANCE CONTROL ACT): Intentional ingredients of this product are listed.

CERCLA (COMPREHENSIVE RESPONSE COMPENSATION,AND LIABILITY ACT): n-Hexane= 5,000 Ibs.

SARA TITLE III (SUPERFUND AMENDMENTS AND REAUTHORIZATIONACT): Hexane (10,000 Ibs.)

311/312 HAZARD CATEGORIES: Immediate, Delayed, Fire.

313 REPORTABLE INGREDIENTS: see section 1

STATE REGULATIONS (Right-To-Know):Pennsylvania RTK: n-Hexane: (generic environmental hazard)Massachusetts RTK: n-Hexane

New Jersey: n-Hexane

CA. PROPOSITION 65:The following statement is made in order to complywith the California Safe Drinking Water and Toxic Enforcement Act of 1986:WARNING This product contains the following substance known to the state of California to cause cancer:

May contain 0-0.002% Benzene

SECTION 15 NOTES: Not intended to be all-inclusive, only selected regulations represented.

SECTION 16: OTHER INFORMATION

CONSUMER PRODUCT SAFETY ACT CERTIFICATION: This product was evaluated by Multi-Marketing Corporation and is certified to be incompliance with the provisions of the Consumer Product Safety Act, the Federal Hazardous Substances Act, and the Poison PreventionPackaging Act, as applicable. This product was manufactured at 3137 26th Street, Los Angeles, CA 90023. The date of manufacture isstamped on the product container. No testing is required to certify compliance with the above mentioned regulations.

DISCLAIMER: Hornady Manufacturing Company believes the information contained in this MSDS to be accurate and complete as of the dateof publication, however no responsibility is assumed for the suitability of this data to the end user or for omissions or errors in its content. Thissheet should be provided to all who use, handle, transport or store the material in question.

PAGE 5 OF 5