7/25/2019 Matubo - návod - MATUBO miniDUO™ and RULLA_ - TARA Bracelet

http://slidepdf.com/reader/full/matubo-navod-matubo-miniduo-and-rulla-tara-bracelet 1/4

 Chiara earrings

Elegant earring component with Matubo Miniduos and Rullas.

Material (for one pair of earrings)

Matubo Miniduo (16 pcs)Matubo Rulla (16 pcs)

Matubo 8!s (8 pcs)

1"! #apanese seed beads (appro$. 1 gram)

11! #apanese seed beads (appro$. 1 gram)

%inch beads (8 pcs)

&eading needle and thread ('mo *ireline)

+ifficult, -ntermediate

1 +esign and tutorial b 'ela /0belo0 (www.gianelle.beadforum.c2)

3utorem tohoto designu a n0odu 4e 'ela /0belo0 (www.gianelle.beadforum.c2)  

www.matubobeads.com

7/25/2019 Matubo - návod - MATUBO miniDUO™ and RULLA_ - TARA Bracelet

http://slidepdf.com/reader/full/matubo-navod-matubo-miniduo-and-rulla-tara-bracelet 2/4

1) 5tring one Rulla one

Miniduo one Rulla one

Miniduo .. . total eight

of each.

) 5lide all the beads

to the end of the

thread. 7ie a suare

9not to form a circle.

7he pass through the

upper hole of the

nearest Rulla.

:) 3dd one 1"! and

pass through the upper

hole of the ne$t

Miniduo.

;) 3dd one 1"! and

pass through the upper

hole of the ne$t Rulla.

") Repeat steps : and

; until (ou reach the

end of the row.

Ma9e the step<up b(

passing through the

first 1"! (ou added in

this row.

6) 'ow the thread e$its

into the gap aboe the

Miniduo.

3dd three 1"!s and

pass through the ne$t

1"! Rulla and 1"!.

=) 'ow the thread e$its

< again < into the gap

aboe the Miniduo.

3dd one 11! one 8!

and one 11! and pass

through the ne$t 1"!

Rulla and 1"!.

8) Repeat steps 6 and

= .. .

>) . . . until (ou reach

the end of the row.

1!) ?eae through

beads to get to the

ne$t corner < between

the 1"! and the 11!.

+esign and tutorial b 'ela /0belo0 (www.gianelle.beadforum.c2)

3utorem tohoto designu a n0odu 4e 'ela /0belo0 (www.gianelle.beadforum.c2)  

www.matubobeads.com

7/25/2019 Matubo - návod - MATUBO miniDUO™ and RULLA_ - TARA Bracelet

http://slidepdf.com/reader/full/matubo-navod-matubo-miniduo-and-rulla-tara-bracelet 3/4

11) @o up through the

first 11! in this

corner.

1) 59ip the 8! and go

down through the

second 11! in the same

corner.

1:) 3dd two 1"!s

three 11!s and two

1"!s and then go up

again through the first

11! from the same

corner.

1;) %ull snug. 'ow (ou

hae created a loop.

1") ?eae through

beads to get to the

ne$t corner .. .

16) . . . and repeat step

11 .. .

1=) . . . step 1 .. .

18) .. . 1: and 1; .. . to

ma9e another loop.

1>) Repeat steps 11 <

1" until there is a loop

in each of the four

corners.

!) 3fter (ou ma9e the

last loop weae

through beads to get to

the middle 11! of

this loop.

: +esign and tutorial b 'ela /0belo0 (www.gianelle.beadforum.c2)

3utorem tohoto designu a n0odu 4e 'ela /0belo0 (www.gianelle.beadforum.c2)  

www.matubobeads.com

7/25/2019 Matubo - návod - MATUBO miniDUO™ and RULLA_ - TARA Bracelet

http://slidepdf.com/reader/full/matubo-navod-matubo-miniduo-and-rulla-tara-bracelet 4/4

1) 3dd one 1"! one

pinch bead and one

1"! and pass through

the middle 11! from

the ne$t loop.

) Repeat step 1 .. .

:) .. . until (ou reach

the end of the row .. .

;) .. . li9e this.

'ow weae through the

last row few more

times. -t is er(

important to do this

because otherwise the

last row would not hold

it As shape.

") 3fter (ou are done

with reinforcing the

last row the thread

should e$it from one of

the pinch beads.

6) 3dd one 11! and

pass through the ne$t

pinch bead.

=) Repeat step 6

until (ou reach the end

of the row.

7hen weae through the

last row few more

times and then tie off

the thread and cut off

all the tails.

8) Ma9e the second earring b( repeating steps 1

< =. Bse 4ump rings to attach earring components

of (our choice.

; +esign and tutorial b 'ela /0belo0 (www.gianelle.beadforum.c2)

3utorem tohoto designu a n0odu 4e 'ela /0belo0 (www.gianelle.beadforum.c2)  

www.matubobeads.com