McDONALD’S DIRECTIONAL WITH ARCH

3’-0 ½”

3’-2

1/1

6”

4’-1

0”

(SIG

N O

AH

)

2” X 2” X 1/8”SQ. TUBE

½” X 20”ANCHOR BOLTS

(QTY 4)

ELECTRICAL CONDUIT

FINISHED GRADE

ANCHOR BOLT MOUNTING DETAIL

(FIG. 1)

ANCHOR BOLT DETAIL

NOTICE:IF PERSONA DOES NOT COORDINATE INSTALLATION, PERSONA CAN NOT BE

HELD RESPONSIBLE FOR ANY VIOLATIONS OF THE SPECIFICATIONS

SET FORTH IN THIS DOCUMENT.THIS DOCUMENT IS FOR BIDDING PURPOSES ONLY. EXACT INSTALLATION PROCEDURES MAY VARY BASED ON SITE SPECIFIC CONDITIONS.

½” THICK 3/4” HOLES½” BOLTS

1” ELECTRICAL HOLE

BASE PLATE DETAIL

½” THICK 9/16” HOLES

½” BOLTS1” ELECTRICAL HOLE

SIGN PLATE DETAIL

7” 6”

7” 6”

5” 4 ½”

5” 4”

McDONALD’S

VARIOUS

6-18-12

McDONALD’S DIRECTIONAL INSTALLATION

MWR/CMFile Name:

Prepared By:Date:Customer:

Location:

Note: Color output may not be exact when viewing or printing this drawing. All colors used are PMS or the closest CMYKequivalent. If these colors are incorrect, please provide the correct PMS match and a revision to this drawing will be made.

Page

1 OF 1Rev

4

700 21st Street SouthwestPO Box 210Watertown, SD 57201-02101 (800) 843-9888 • www.persona-inc.com

DISTRIBUTED BY SIGN UP COMPANY

DIRECTIONAL INSTALLATION INSTRUCTIONS:

1. General contractor to stake sign location(s), establish final grade requirements and determine the sign orientation on the property, prior to excavation.2. General contractor to excavate directional foundations, set anchor bolts and conduit per template included with plate & bolt kit. Pour concrete according to engineered drawing specifications .3. Uncrate and inspect sign & faces (faces packaged separately). Notify Persona of any damage.4. Place leveling nuts & washers on anchor bolts (see anchor bolt detail) and level temporarily for final adjustment later.5. Feed primary electrical wires up through the base column and plates. 6. Feed primary electrical wires through the hole in bottom of sign frame and bolt sign to matching plate on support column. Tie a strain relief knot in the primary wires within the sign frame to prevent wires from falling back and to prevent poor connections. 7. If authorized to do so, make final electrical connections to primary power. Shorten wires prior to making final connections to avoid excess wires shadowing on the faces when illuminated. Test light for proper illumination.8. Install directional faces with graphics as required for each specified location.9. Re-check sign for level, make final adjustments, and tighten nuts on anchor bolts.10. Touch up any paint on sign, bolts or structure as required.11. Clean area. Remove excess soil & discard installation debris off-premise.

(see note)

Bolt down over leveling nuts.

elevation: 16 / plates: 8

ANCHOR BOLT DETAIL

BASE PLATE

DOUBLE NUT

PLATE WASHER

CONCRETEFOOTING

½” Ø GALVANIZED ANCHOR BOLT

20” LONG W/ 5” THREAD @ TOP & 2” THREAD

@ BOTTOM; 5 NUTS & 3 PLATE WASHERS

PER BOLT

LEVELING NUT& PLATE WASHER

DOUBLE NUT & PLATE WASHER

**NOTE: ALL PLATE WASHERS, NUTS, & LOCK NUTS TO REMAIN ON BOLTS DURING INSTALLATION OF FOUNDATION TO AVOID BEING MISPLACED ON THE JOB SITE

This sign is intended to be installed in accordance With the requirements of article 600 of the national Electrical Code and / or applicable local codes.This includes proper grounding and bonding of the sign.

NOTE: REFERENCE ENGINEERED DRAWINGS FOR DETAILS:

Any modifications to base plates, anchor bolts, or any other structural elements must be approved by a registered structural engineer and documented on

a stamped print

http://www.personasigns.com/mcdonalds/products.htm

ELECTRICAL SPECIFICATIONS:1. ILLUMINATION: WHITE LEDS2. POWER SUPPLY: (1) LED POWER SUPPLY3. LOAD: 0.85 AMPS 4. CIRCUITS: (1) 20 AMP - 120 VOLT

ELECTRICAL SPECIFICATIONS:1. ILLUMINATION: WHITE LEDS2. POWER SUPPLY: (1) LED POWER SUPPLY3. LOAD: 0.32 AMPS 4. CIRCUITS: (1) 20 AMP - 120 VOLT

McDONALD’S DIRECTIONAL WITHOUT ARCH

3’-0 ½”

1’-3

½”

NOTICE:IF PERSONA DOES NOT COORDINATE INSTALLATION, PERSONA CAN NOT BE

HELD RESPONSIBLE FOR ANY VIOLATIONS OF THE SPECIFICATIONS

SET FORTH IN THIS DOCUMENT.THIS DOCUMENT IS FOR BIDDING PURPOSES ONLY. EXACT INSTALLATION PROCEDURES MAY VARY BASED ON SITE SPECIFIC CONDITIONS.

McDONALD’S

VARIOUS

6-18-12

McDONALD’S DIRECTIONAL INSTALLATION

MWR/CMFile Name:

Prepared By:Date:Customer:

Location:

Note: Color output may not be exact when viewing or printing this drawing. All colors used are PMS or the closest CMYKequivalent. If these colors are incorrect, please provide the correct PMS match and a revision to this drawing will be made.

Page

1 OF 1Rev

4

700 21st Street SouthwestPO Box 210Watertown, SD 57201-02101 (800) 843-9888 • www.persona-inc.com

DISTRIBUTED BY SIGN UP COMPANY

½” THICK 3/4” HOLES½” BOLTS

1” ELECTRICAL HOLE

BASE PLATE DETAIL

½” THICK 9/16” HOLES

½” BOLTS1” ELECTRICAL HOLE

SIGN PLATE DETAIL

7” 6”

7” 6”

5” 4 ½”

5” 4”

elevation: 16 / plates: 8

2’-11

7/1

6”

(SIG

N O

AH

)

2” X 2” X 1/8”SQ. TUBE

½” X 20”ANCHOR BOLTS

(QTY 4)

ELECTRICAL CONDUIT

FINISHED GRADE

ANCHOR BOLT MOUNTING DETAIL

(FIG. 1)

ANCHOR BOLT DETAIL

ANCHOR BOLT DETAIL

BASE PLATE

DOUBLE NUT

PLATE WASHER

CONCRETEFOOTING

½” Ø GALVANIZED ANCHOR BOLT

20” LONG W/ 5” THREAD @ TOP & 2” THREAD

@ BOTTOM; 5 NUTS & 3 PLATE WASHERS

PER BOLT

LEVELING NUT& PLATE WASHER

DOUBLE NUT & PLATE WASHER

**NOTE: ALL PLATE WASHERS, NUTS, & LOCK NUTS TO REMAIN ON BOLTS DURING INSTALLATION OF FOUNDATION TO AVOID BEING MISPLACED ON THE JOB SITE

This sign is intended to be installed in accordance With the requirements of article 600 of the national Electrical Code and / or applicable local codes.This includes proper grounding and bonding of the sign.

NOTE: REFERENCE ENGINEERED DRAWINGS FOR DETAILS:

Any modifications to base plates, anchor bolts, or any other structural elements must be approved by a registered structural engineer and documented on

a stamped print

http://www.personasigns.com/mcdonalds/products.htm

DIRECTIONAL INSTALLATION INSTRUCTIONS:

1. General contractor to stake sign location(s), establish final grade requirements and determine the sign orientation on the property, prior to excavation.2. General contractor to excavate directional foundations, set anchor bolts and conduit per template included with plate & bolt kit. Pour concrete according to engineered drawing specifications .3. Uncrate and inspect sign & faces (faces packaged separately). Notify Persona of any damage.4. Place leveling nuts & washers on anchor bolts (see anchor bolt detail) and level temporarily for final adjustment later.5. Feed primary electrical wires up through the base column and plates. 6. Feed primary electrical wires through the hole in bottom of sign frame and bolt sign to matching plate on support column. Tie a strain relief knot in the primary wires within the sign frame to prevent wires from falling back and to prevent poor connections. 7. If authorized to do so, make final electrical connections to primary power. Shorten wires prior to making final connections to avoid excess wires shadowing on the faces when illuminated. Test light for proper illumination.8. Install directional faces with graphics as required for each specified location.9. Re-check sign for level, make final adjustments, and tighten nuts on anchor bolts.10. Touch up any paint on sign, bolts or structure as required.11. Clean area. Remove excess soil & discard installation debris off-premise.

(see note)

Bolt down over leveling nuts.