md110 forum
TRANSCRIPT
Can't remove call log
NCCOI (IS/IT--Management) 27 Feb 07 2:37
Hi there,
See below:
<cldfp; FILE ADMINISTRATION DATAFILE STATEAAU ACT IODEV/PATH USER DEVICE STATE PRIORITY CALL-LOGGING CIL-1 READY/STARTED CFILE STATETTMS ACT IODEV/PATH USER DEVICE STATE PRIORITY CALL-LOG-TTMS NONE READY/STARTED C CALL-LOG-TTMS2 NONE PASSIVE CEND <cldfe:iodev=call-log-ttms2,user=none;NOT ACCEPTEDFILE IS ACTIVE<
Although the cldfp says file is passive i can't remove call-log-ttms2 because cldfe says it's active.
What's the problem?
Thanx i.a.
whosrdaddy (Vendor) 27 Feb 07 7:07 use clode; and clohe; before cldfe; ----------------------------------------------------- What You See Is What You GetNever underestimate tha powah of tha google!
NCCOI (IS/IT--Management) 27 Feb 07 8:38 But what about the call-log-ttms in the same file ..?I have a call-log-ttms and a call-log-ttms2.This last one must be removed.
T.i.a.
whosrdaddy (Vendor) 27 Feb 07 9:37 look at CLINP;
you can give the file parameter with CLOHE; command ----------------------------------------------------- What You See Is What You Get
Never underestimate tha powah of tha google!
Direct Inward Dial - ISDN
tim080772 (TechnicalUser) 4 Jul 02 23:16 Hi guys (and girls if there are any in the forum)
I have just finished setting up a basic single LIM MD110 with BC 7.2 (Yes I know it's old, its for my test lab). The problem I have now is that the system terminates every incoming DID number on the attendant console. NADAP looks fine as do all the route settings, can anyone point me in the right direction to find whats missing?
Many thanks in advance.Tim Russellhttp://www.russellweb.co.uk/nortel
Rou5 (TechnicalUser) 5 Jul 02 6:12 Hi You can check following settings.!!opcgs , Operator call origin group set opcts, Operator call type data set RODNI Route day and night number initiate
here is some example, listing from md bc 7.2CALENDAR DATAVERSION=FIBC7.2A/CORR311:50:4205 JUL 2002<OPDDP:DIR=ALL; OPERATOR DIRECTORY DATA DIR EQU OCUST TYPE 890 001-0-10-00 - 1<OPCTP:CORG=ALL;OPERATOR CALL TYPE DATA CORG CALT ROU OACC CUST NDIR RERNUM CEN 1 1 - 9 - N - N 2 2 - 9 - N - N 3 3 - 9 - N - N 7 7 1 311 - Y 490 N<OPCGP:CORG=ALL; OPERATOR CALL ORIGIN GROUP DATA DIR 8 9 0CORG - 1 1 2 1 3 1 7 1<RODNP:ROU=ALL;;
ROUTE DAY AND NIGHT NUMBER DATA ROU TRU DAY NIG 1 9 490 <NADAP:NUMTYP=OC&OD;NUMBER ANALYSIS DATA TYPE OF SERIES NUMBER SERIES OPERATOR COMMON NUMBER SERIES 9OPERATOR COM. DID. NUM. SERIES 311
Obs. nig and day settings.!!test these...
GuauGuau (TechnicalUser) 8 Jul 02 5:58 Have tou checked NUTRP; settings? If B-number conversion isn't correct, calls could be rerouted to operator console.You should check traffic matrix (TCMAP:CON=T;) too.Good look!
tim080772 (TechnicalUser) 8 Jul 02 6:03 Thanks for the answers. I believe the problem was with the ISDN30 setup. I have now routed the ISDN to the Lab Meridian and instigated a QSIG link between the Meridian and the Ericsson, this works fine. I'll go back to the original setup when I can get someone to reconfigure the ISDN30 for me.
Tim Russellhttp://www.russellweb.co.uk/nortel
tim080772 (TechnicalUser) 15 Jul 02 5:20 So I've got it working now, here is the config:
ROCAP (ROCAI / ROCAE)ROU SEL TRM SERV NODG DIST DISL TRAF SIG BCAP2 111000000700 5 0000030111 0 30 128 00151515 111110000030 1111
RODAP (RODAI to initiate)ROU TYPE VARC VARI VARO FILTER 2 SL60 H'00000300 H'00000000 H'04010000 NO
This is for a Dutch EuroISDN30.
MD110 connection to An other PBX via LL a CISCO
mkhalil (IS/IT--Management) 8 May 02 12:30 HI,I'm looking for a solution for connecting an MD110 located in the Head Office (220 users) to an old Matra PBX in a remote site (60 users). The head office is connected to this site with an 128K Leased line for IP traffic via CISCO 3640 (Head Office) and CISCO 2610 (Remote site). Is there any options to use this link for voice ?
ysgoh88 (TechnicalUser) 8 May 02 21:42 You can used E&M tie line or Q-sig tie line to tie with the cisco at both side.this should work and cisco router should be able to provide this.
MD6 (TechnicalUser) 10 May 02 16:44 Hi,
How many connections you need at both side? Your link (128K) have free bandwith?
MD6
mkhalil (IS/IT--Management) 10 May 02 17:16 3 to 4 simultaneous connections will be OK and 40% of the bandwidth almost 50k. Many thanks in advance for your help.
Regards,
ysgoh88 (TechnicalUser) 11 May 02 1:47 then you can just used E&M tie line,and more easy for test.
How do I create a new user/password in BC10
ciceronen (TechnicalUser) 17 Sep 02 4:02 HiI'd like to know how I do to create a new user, that only have the right to read information (like isepp; SYEDP; OPCGP; and more) in a BC10. I would also like to know the differenses between a IPU and a NUI? What cables do I need to connect to the IPU/NUI cards?
mduser (TechnicalUser) 17 Sep 02 5:12 To create a new user, you first have to pinpoint what kind of I/O board is used. The IPU has only 1 password for each login level (0, 1,2,... 7). Th NIU board uses Username / Password and can have several usernames for the same level. This also explayins the differences on login. It's more security. Also you have the Ethernet possibility for the NIU and the IPU hasn't.
Normaly all printcommands are available in level 1.
To create a new user:
IPU: IOPWC:AUTH=<login level>,PSW=<password>;example: IOPWC:AUTH=1,PSW=SECRET;
niu: IOUAI:NAME=<username>,PSW=<password>,AUTH=<login level>;example: IOUAI:NAME=LEVEL1USER,PSW=SECRET,AUTH=1;
To print: IOPWP for IPU (passwords are shown).IOUAP for NIU (passwords aren't shown).
NIU cable: TSR 902 0459/10000
ciceronen (TechnicalUser) 17 Sep 02 5:23 Thank you
lalrl1 (TechnicalUser) 17 Sep 02 15:09 Hi,
to give a user certain rights for certain commands, use the command iocap and you will see, in which class you can do which action. Then use iocac and rearrange the commands.
MB
Hi again, How can I set up a voice
scuzzie (IS/IT--Management) 17 Sep 01 11:15 Hi again,How can I set up a voice category which permits sets to receive calls only???Thanx again
Scuzzie
Guest (Visitor) 30 Dec 01 9:46 Scuzzie,Yeah! you can restrict out dialing frm a particular phone
Vipin
yubaile (IS/IT--Management) 21 Aug 02 13:11 you can configurate with a spexi command
ysgoh88 (TechnicalUser) 27 Aug 02 2:30 better way is to restric from the traffic matrix.is very easy. just need to make sure that the traffic matrix is just for incoming.
UKboy (Programmer) 30 Aug 02 7:08 why not just use the cat peramiters to restrict outgoing calls, its what its designed to do?!?
yubaile (IS/IT--Management) 11 Sep 02 9:20 a better way is in the TRAF parameter in the extei o ksexi command to put TRAF=00000000
lalrl1 (TechnicalUser) 19 Sep 02 16:05 Hallo yubaille,
it is not sure, that it will help! You could block incoming calls too! Important ist traf=xxyyyyzz and here only yyyy. So check nadap and find in the tcd-categorie an unused amount (maybe 12). If you have a dialplan for example 100&&499 Then make nacds:cdcat=12,num=1&2&3&4; So the extension can dial internally. Then make a new category with exccs:cat=,traf=001212yy,....; Then give the extension the new cat with kscac/excac.
MB
I can't do dial-upthread806-377242Share This Forum Search FAQs Links Jobs Whitepapers MVPs
Check Out Our Whitepaper Library. Click Here.XCatalin (TechnicalUser) 9 Oct 02 7:49 I can't do dial-up connection trough an analogue extension.I have 1 digital trunk (2Mbps) for DID, connected at md110.For telephone calling it work good.If I try to connecting to the Internet, using dial-up trough an analogue extensions, the connection is establish, but after 2-3 min the connection is cut and I don't now why.Help.
TBLuk (Vendor) 9 Oct 02 8:19 This sounds like a sync problem.
Check the ALLOP table, are there any 274 alarms for Digital Trunk, clock malfunction (slip)?
Check the SCEXP; depending on your system setup and the amount of LIMs, you should have at least have a first choice Master LIM sych source. Check it's description under the 'Status' field. It should be sitting at SYNC RECEIVING.Any other clock sources such as Second Choice in the Master LIM, or First Choice in the Sparemaster LIM, should be sitting at an OK state.
If the First Choice source is not sitting at OK, but is displaying FAULTY or NOT PRESENT, you have a major problem, so post back here with the details!
PS If it *is* a sync problem, then you may also be able to hear slight crackles and jitters on voice calls as well.
XCatalin (TechnicalUser) 10 Oct 02 7:05 In ALLOP I have the alarm 274, Digital Trunk, clock malfunction.The answer for SCEXP is:SCEXP; EXTERNAL SYNC RECEIVING LINES DATANO DATA AVAILIBLE
What is the next step?
TBLuk (Vendor) 10 Oct 02 8:06 Ok you have no external clock source, so the MD110 is effectively 'running free'.
You need to setup a synchronisation source.
Do you know the board postion (LIM-MAG-SLOT) of your E1 card?
If so, just do the following command, I've used 1-0-00 as an example:
SCEXI:FEML=001-0-00-00;
It will say EXECUTED.
Wait about one minute for the clocking to take place, then do a SCEXP;
If you try and do the SCEXP too soon it will say EXECUTION INHIBITED.
Hope this helps.
XCatalin (TechnicalUser) 11 Oct 02 3:43 Hello TBLuk,I did exactly what you said.Now I reveive sync, and after that I verified the dial-up, it's a stabile connection.Thank you again.
TBLuk (Vendor) 11 Oct 02 10:39 Wicked, glad to hear it
Good
GE COMMANDSthread806-375283Share This Forum Search FAQs Links Jobs Whitepapers MVPs
Find A Job or Post a Job Opening Click Here.
fellicciano (TechnicalUser) 5 Oct 02 16:10
ANYONE COULD HELP ME WITH THE GE COMMANDS ?I DONT`T KNOW HOW TO USE THEM, COULD ANYONE SHOW ME AN APLICATION EXEMPLE WITH THEM?
Isinor (Instructor) 7 Oct 02 10:39 You could try reading the GE operational directions in Alex.
GE commands are used in various applications... DECT (Mobility), IP Extension, Integrated Voice Mail, Free-seating & SMS.
GE extensions are not associated with an EQU position, they also do not use common categories, they have a CSP (Common Service Profile) which is just like a common cat with the TRAF SERV CIDIV and ADC parameters all messed about to confuse old timers.
This example is a Mobility DECT Extension
You should create a CSP (common service profile) first...GESPI:CSP=0,TRAF=1113151515,SERV=206020000,CDIV=11510000,ROC=000001,NPRES=101;
Note CSP=0 has to be the first CSP code initiated in the exchange.
You then need a free EX number SUVIP:NUMTYP=EX; or NANSI:NUMTYP=EX,NUMSE=xxx;
Associate the DIR with a CSP…GEDII:DIR=2000,LIM= 3,CSP=0;
Then link the DIR to an IPEI and AUTHKEYCXAKI:DIR=2000,IPEI=0000707404102,AUTKEY=1111;
Good luck
Connect NokiaPremicell to MD110thread806-395110Share This Forum Search FAQs Links Jobs Whitepapers MVPs
XCatalin (TechnicalUser) 1 Nov 02 3:56 I have some GSM interface (NokiaPremicell and Nokia22) and I want to connect to MD110. How could do this? I must use LCR commands?
Avstral (TechnicalUser) 3 Nov 02 18:21 Going to connect almost any EXTERNAL equipment to MD110, you have to use some signalisation method between this equipment and MD.
Both physical connection and signalisation could be analog or digital.
Having basic info about interface & signaling type realized on your external device, you can chouse appropriate board type in MD, define which program unit you need and make programming for incoming/outgoing route.
You are to use NA-commands to expand your numeration plan (add some access code) and RO-commands to program all the interface parameters and connect hardware equipment.
If you never did this before, it could be rather complicated and you will need some more experience person on site to help with.
Regards
mduser (TechnicalUser) 4 Nov 02 4:44 In the past we used the Nokia Premicell. We connected it on a TLU-75/1 to the MD110. As we don't use it anby more I can't see the route parameters (ROCAI/RODAI) anymore. It was an external route with a route access code (DEST). LCR is optional to use.
At this moment we use the AS522 GSM Gateway which is connected to the Md110 (Bc10) over an TLU79 board (ISDN 2B+D) ... for info look at http://www.mcs-nl.com/as520_uk.htm
Route settings:ROCAI:ROU=...,TRM=5,SEL=711000000000001,SIG=511100000030,SERV=3101000001,TRAF=00151515,BCAP=111111;RODAI:ROU=...,VARC=00000344,VARI=10030000,VARO=44310000,TYPE=SL60;ROEQI:ROU=...,TRU=1-1&1-2,EQU=...-.-..-0;
Okoskata (TechnicalUser) 4 Nov 02 9:34 We are currently using 3 Nokia Premicells, with the following settings:ROCAI:ROU=...,TRM=3,SEL=013000000000001,SIG=110100000000,SERV=2100030000,TRAF=00151513,BCAP=111110;RODAI:ROU=...,VARC=00000100,VARI=00000002,VARO=00000009,TYPE=TL1;
call waiting analogthread806-389629Share This Forum Search FAQs Links Jobs Whitepapers MVPs
Tek-Tips Forums is Member Supported. Click Here to donate.Hitechbuzz (TechnicalUser) 24 Oct 02 18:29 have tried to set up a standard analog extension with call waiting works ok but not call waiting. System BC10 up to date service packsusing EXTEI:------serv=00021106--- does not work any ideas thanks Guys
mduser (TechnicalUser) 27 Oct 02 11:42
Your setting of the SERV: D1D2D3D4D5D6D7D8 = 00021106
D3D4 = 02 = Open for intrusion and reception of call waiting tone from another party.
D7D8 = 06 = Reception of call waiting tone from antother extension, PABX operator and external line permitted.
If you also want to initiate Call waiting from this extension you should change this setting to:
D7D8 = 07 = Reception of call waiting tone from antother extension, PABX operator and external line permitted (06) & permitted to initiate transmission of call waiting (01).
Just make three extensions with SERV = xx02xx07 and you will see it work.
Good trick if you can do it.thread806-372654Share This Forum Search FAQs Links Jobs Whitepapers MVPs
Arnoldnt (TechnicalUser) 2 Oct 02 9:57 People,
I need some help on a little problem that I've got.......
I currently deal with alot of extension moves and changes each day but one thing that bugging me. When i go to carry out the changes the exetensions are in use ....
As you well know the extension has to be free in order to renumber it, End it, etc etc
Is there anyway that I can end a call on an extension from the console ?Is there a program unit that can be stopped ???
Thanks in advance
Avstral (TechnicalUser) 2 Oct 02 19:10 Man,
What the console do you mean?
In common, there is no special command to stop only one established conversation and you can't stop PU.
1. First of all, block EQU position with BLEQI:EQU= ;If you can't wait and want stop the talk ASAP, you can proceed with:
2. Restart respective ELU board (RFBOI:BPOS=....;).But ALL the ext-s on the board will be interrupted.
3. Restart ELP6 or KLP1T1 program unit in LIM (RFPUI:LIM= ,UNIT= ;). But ALL analog or digital ext-s in the LIM wil be interrupted
4. In case of external connection, trace with CTDEI:DIR= ; trunk board and restart it or respecteg PU.But ALL the calls via this trunk board will be canceled.For some traffic case or trunk boards you will disturb less amount of ext-s compare to 2&3.
5. Absolutely not recommended for this case but still possible RFEXI; command. But you will interrupt traffic on ALL the exchange.
Too easy...
Gallian (TechnicalUser) 21 Oct 02 2:28
Hi,What you can do is Ctdei:dir =Busy Dir Number then do LSCOE on both the Equipment positions u will see in CTDEI.LSCOE:EQUA= "The Tone sender equipment position" EQUB="The directory Number equipment" and use CONTYP=3;Do the same command other way round as well with EQUA as Dir Equipment position and EQUB as tone sender position.This should disconnect the ongoing call.U wouldnt have to restart a program unit.BRecptfa
joka (TechnicalUser) 22 Oct 02 4:41 If you have ApplicationLink there is a simple way to solve this. There is a CSTA test tool included in ApplicationLink called ncstatool.exe. Use this to set up a monitor on the existing call and then just give the command to clear the call.
/Jonas
TBLuk (Vendor) 22 Oct 02 9:30 In response to epctfa,
LSCOE only ends the connection within the LSU, if you put the call on hold, and then back again, you are re-connected, for SUSIP purposes the device looks free, but is still marked as busy.
Periodically congestion in LIM1-need helpthread806-360840Share This Forum Search FAQs Links Jobs Whitepapers MVPs
Find A Job or Post a Job Opening Click Here.wladimir (TechnicalUser) 17 Sep 02 5:43 Hi!MD110 ver 9Sometimes (app. every 1.5-2 month) all outgoing calls from sets connected to LIM1 (at all - 3 LIMs + 1 GS) are impossible. Incoming calls and calls from other LIMs - OK.In ALLOP - no errors.FTMFI,GSFTI-OK. On EL6 and EL8 sets - congestion tone (shorter,than busy) on KS screens - CONGESTION. After restart LIM1 (BLLTI, RFLII, BLLTE) - all OK (some time to next "congestion"). What is wrong?
Jaydee2002 (IS/IT--Management) 17 Sep 02 6:44 Hi,
Wladimir How many PCM links do you have to the GS? Have checked that there is sufficient capacity there?
JD
wladimir (TechnicalUser) 17 Sep 02 8:11 Hi, Jajdee!It's 1 link to GS, but I think, that's no matter, because this error appear after week-end (traffic is _wery_ low) and newer "at once" - usually number of "congested" sets increasing from some to all at some hours. And congestion tone appears _before_ dialing any number - immediatly after lifting handset.
lalrl1 (TechnicalUser) 17 Sep 02 14:48 Hi,
what kind of external lines is connected to lim1? sl60? Internal calls within lim1 is possible? Internal calls to lim2 is possible? Next time try to start not the whole lim (rfrli would be easier than rflii)but only a single programm to fix the problem, for example klp1t1 or slp60
MB
wladimir (TechnicalUser) 18 Sep 02 0:44 Hi, DEMIBE2!In LIM1 - only TLU75(TLP95). At first, all calls are possible (some sets some times gets "congestion" after lifting handset, after 2-5 attemptions they can make call, incomming calls -OK). Number of "congestions" increasing very fast, and 3-4 hrs later all sets in LIM1 gets "congestion" immediatly after lifting handset (before any dial). At first, I tryed restart all PU-s in LIM1 sequentally. But work only full LIM restart.
Petya (Programmer) 18 Sep 02 1:20 Hi, Wladimir.I had absolutely the same problem. This problem is in very high traffic. If load of LIM more than 1.2 calls/second new calls are rejected. You should ask your local Ericsson company for patch 73006. This patch increases the max load level in LIM from 1.2 to 1.8 calls/second.
Orim (TechnicalUser) 18 Sep 02 2:58 Hi Vladimir,I had the same problem. I fixed it by replacing (not with new one) LSU and DSU board. Only pull and push
these boards 2-3 times. Replace the connectors too.
Avstral (TechnicalUser) 29 Sep 02 23:08 To Petya:Sorry, this is not high traffic problem. There is no alarm 320 and incoming traffic possible.
This look likes a problem with TMU in LIM 1.
To Vova: 1. Could you, please, check your software version with CADAP; command.
2. Check with CNLIP:LIM=1,DEV=ALL; number of TMU's installed in LIM 1. (They have BRDID=102).
3. How many extencions do you have in LIM 1?It is recommended by E/// to have 1 TMU per 80 extensions.
4. Check revision state for: TMU (it MUST R3A), LPU5, LSU and DSU's.
How to fight with this problem:
1. If this problem appear again, make FTTDI:LIM=1; LSFTI:LIM=1,FULL=YES;, check also HIMDP:LIM=1;
Try to restart with RFBOI:BPOS=...; TMU boards and program unit:RFPUI:LIM=1,UNIT=TSP;
2. If you have spare TMU - swap them in the evening.
3. DON'T WARRY, BE HAPPY.
It is IMXO.
It is extremely useful to make SFCEI; and RFEXI; at least once a month.
Clean up the brain, relief from the pain.
TBLuk (Vendor) 9 Oct 02 7:56 I agree this has, but also disagree with Avstral:
We need to know what CNA level you are at by doing a CADAP;
TMU does not *need* to be R3A, as it may be a TMU1 in the system rather than a TMU2
There is a problem with several variants of the TMU1 and TMU2, mainly TMU1 ROF1375335/1 at any revision, or the TMU2 ROF1375335/2 at R3 or higher, but we'll come to that later.
I would not agree with the fact that a RFEXI is required every month, this is totally unnecessary, and I cannot see the thinking behind it. A system should never need RFEXI'd in normal operation.One of the networks we operate is safety critical, and none of these 180 MD110's have been restarted in
over two years!
Avstral (TechnicalUser) 27 Oct 02 22:31 To TBLuk:
I've reed you post several times, but didn't catch, what do you agree with and what not.
Anyhow, I'll try to answer you step by step.
We need to know what CNA level you are at by doing a CADAP;
Great, this was the first point in my message to Wladimir.Just check it upper.
"TMU does not *need* to be R3A, as it may be a TMU1 in the system rather than a TMU2;There is a problem with several variants of the TMU1 and TMU2, mainly TMU1 ROF1375335/1 at any revision, or the TMU2 ROF1375335/2 at R3 or higher, but we'll come to that later.
I really didn’t mention about TMU /1 before, so let’s open Upgrade System Support (USS) program and check board status for TMU.
TMU board with ROF1375335/1 had releases from R1A to R6A.
Boards with R1A to R4A are to be modified to TMU2 ROF1375335/2 with R3.Boards with R5A are to be upgraded to TMU ROF1375335/2 with R3A changing two proms.Boards with R6A are OK for BC9 – BC11.
TMU board with ROF1375335/2 had releases from R1A to R3A.Boards with R1A and R2A are to be upgraded to with R3A changing one prom.Boards with R3A are OK for BC9 – BC11.
So, I still insist that TMU board MUST be R3A for almost all hardware. If you have TMU /1, you can relax only with R6A version. But! TMU /1 has never been delivered to Russia with BC9 (this is Russia because of TLP95 using). And if this exchange was upgraded from BC7, TMU was upgraded either.
TMU ROF1375335/2 higher than R3 not exist at all. Sorry.
I would not agree with the fact that a RFEXI is required every month, this is totally unnecessary, and I cannot see the thinking behind it.…One of the networks we operate is safety critical, and none of these 180 MD110's have been restarted in over two years!
My congratulations! You have very stabile and reliable MD net.
Just a question. In witch country?
When you work in Russia, you can forget about all your previous experience.
If you wish, I would organize a trip for you to Siberia. In 1995-2001 we installed there more than 300 LIMs in very different configurations (biggest transit node has 41 LIMs with GS). In this area, regular SFCEI+RFEXI set of commands is part of maintenance routine and executing regularly. Being there you can explain to maintenance personnel that you “cannot see the thinking behind it”.
Nothing personal.
Best regards
TBLuk (Vendor) 28 Oct 02 9:11 RE: The TMU issue.
I am going on what we have in the UK, and the part you quoted me on about the TMU revision was taken directly from an Ericsson patch report, on a TMU congestion problem we have had on our expansive MD110 network of around 200 sites with some sites having one LIM upto 20+ LIMs.The patch in question solved the problem, I will need to look into if it is a UK specific patch.
As you say 'TMU board MUST be R3A for almost all hardware', but there is still a version of TMU1 for which this is not the case, so your argument holds little water.
Regarding the CADAP, yes you did ask for it, but he did not provide it, so I asked again, he still did not reply.
Regarding SFCEI and RFEXI, my apologies, you have a very unstable network if you need to do these commands as part of routine maintenance, if these were routine maintenance commands they would be listed in the documented procedures.
I do not wish to enter into an argument, but wish to have a nice devate
Route Reportingthread806-409250Share This Forum Search FAQs Links Jobs Whitepapers MVPs
MJ6 (IS/IT--Management) 19 Nov 02 9:34 First post-joined today. I have sussed PCM Link reporting but need to report on Routes which arent currently being reported on. I have route numbers but need to check trunks relating to Route. Can someone help? :)
shaun123 (IS/IT--Management) 19 Nov 02 17:32 hithe commands you need aretrroi:rou=,timei=,timee=,date=roeqp:rou=,tru=allshaun
MJ6 (IS/IT--Management) 20 Nov 02 3:25 Shaun123-
ROEQP:ROU=x,TRU=ALL; didn't work-"COMMAND UNKNOWN". We've got BC10 if that helps. Is there a different comand for BC10?
eriuser (TechnicalUser) 20 Nov 02 4:49
Try rOEDP
MJ6 (IS/IT--Management) 20 Nov 02 5:21 Thanks.
Time of Day Routing ?thread806-401846Share This Forum Search FAQs Links Jobs Whitepapers MVPs
Check Out Our Whitepaper Library. Click Here.73vette (TechnicalUser) 9 Nov 02 17:31 Does anyone know how to do Time of Day Routing on an Extension or Hunt group? For example if you dial XXXX it will ring at a certain phone from 8-5 and then at a different phone at other times?
Regards.
dognbone (Programmer) 11 Nov 02 17:09 If you have a voice mail system you could time of day switch it.
73vette (TechnicalUser) 11 Nov 02 17:45 Thanks,
I know the MD can do it on the trunk level and this customer does not use voice mail on the front end........so back to the drawing board!
Cheers!
lalrl (TechnicalUser) 12 Nov 02 14:29 You have two chances:
1. You have DNA connected to the MD110. Then you can change the diversion for a blind grouphuntinggroup or ACD-group via Batchmode.
2. You have a lot of money! Then use time-of-day-function and least cost routing. Buy 2 Trunk-boards, make a physical loop between the boards and then use time-of-day function with least-cost-routing. Then you are free to decide where the call should go - based on day and time.
lalrl
73vette (TechnicalUser) 13 Nov 02 7:48 lalrl,
Can you expand on you idea with the 2 trunk cards?
We have many spare TLU75 ports. This number would be dialed internally only ext. possible hunt group.
Are you thinking of using RODDI AND RODNI?
Regards
lalrl (TechnicalUser) 17 Nov 02 7:48 Hallo 73vette,
I do not know exactly functon of TLU75. I think with this card you can have analouge trunk- or tielines. If so, you can use this cards. You must have so called routes (programmed with rocai, rodai, nansi:numtyp=ed,numse=aa;roddi:dest=aa...) Try to install tie-lines to your own system - by physical loop of two cards.If successful, caller has to dial the destination. This destination is configured as LC in nadap
and the dest will then be supervised by LCR with time of day. Then you can use the commands
lctdi...;lcddi:tab=fdt,frct=,...;, lcddi:tab=dnt1,frct=,entry=,trc=,pre=;
lalrl
Avstral (TechnicalUser) 18 Nov 02 4:06 To lalrl
This will definitely work. TLU75 is a 2-wire loop-start trunk board. Almost the same, as TLP11 or TLU44. All the difference is in number of the ports and filters installed on board. All three works with TLP11 PU.
The only problem could be visible time delay because of analog board’s nature: register signaling there is, in best case, rather slow DTMF.
Category ( TRAF digits 7 & 8 )thread806-412320Share This Forum Search FAQs Links Jobs Whitepapers MVPs
Check Out Our Whitepaper Library. Click Here.Arnoldnt (TechnicalUser) 22 Nov 02 7:13 Hi,
Can somebody tell me What the last 2 digits do on the TRAF Parameter ( Digit's 7 & 8 )
I've got a couple set to 01151515
Anybody know what they do or can you point me in the right direction to find out !!!
Thanks In advance
Arnoldnt
shaun123 (IS/IT--Management) 22 Nov 02 12:47 digits 7 and 8 refer to the tcmap 15 means that the extn is fully open do tcmap;(return)this will show u the traffic connection matrix for both conferance and trunk to trunk connections etclook in either dynatext or alex under tc commands(traffic connection from memory)
lalrl (TechnicalUser) 22 Nov 02 14:17 Hallo shaun,
is it really true, that tcmap; shows you both tables? Is n´t it better to make: tcmap:con=t; for normal traffic, and tcmap:con=c; for conference?
lalrl
eriuser (TechnicalUser) 27 Nov 02 7:50 Or you can try TCMAP:CON=ALL;
This is not only for Trunk or conference connections but for all devices & groups.
Backing up to an external HDthread806-425613Share This Forum Search FAQs Links Jobs Whitepapers MVPs
Mithrandir01 (MIS) 11 Dec 02 9:13 When I attended the MD110 "Implement and Manage" class, the instructor mentioned at the very end of the class that it was possible to telnet into the NIU and copy REL1 to another HD (like your local HD on your computer). I am not very familiar with telneting; can anyone tell me more specifically how to do this? We're using BC9. Thanks in advance!
Mithrandir01 (MIS) 11 Dec 02 14:15 For anyone who was wondering, this was the reply I got when I e-mailed the instructor with my question:
You can't telnet into the system with BC9...you must have BC11 and the NIU board. The NIU will have an IP address assigned to it with a LAN connection, and you can FTP into that and transfer the disk contents with an FTP command. I use WSFTP LE from IPswitch.com, it's easy (and free). There are a lot of FTP programs out on the web that make it so much easier than using a DOS window. So, the short answer is that you can't do it with BC9...better off with a spare HDU and swap them out occasionaly to keep them updated.
You used to be able to do it with MDDISKTOOL and a special SCSI cable that would dump directly to a PC, but I don't know if that is still available. Also, PCREGEN can handle something similar..basically, it sucks all the data off the system with a series of print commands, and regenerates files that will rebuild the system from ground zero. It is NOT a backup of the system, just the customer data (routes, phones, etc...) that will recreate your system in the event that you have to reload from a brand new disk with no backup on it.
shaun123 (IS/IT--Management) 11 Dec 02 17:08 you can also telnet on bc10 as the niu is used on bc10 as well
BC9CONSONO (TechnicalUser) 12 Dec 02 16:44 W/o eth port on your i/o board (like IPU) u can do nothing with telnet but with pc soft disk (ancient) or md disk tool (advanced) local of course... Hovewer, some kind people designed programs like rs232/telnet to use on your terminal pc...
How setting network connection on NIU?thread806-457645Share This Forum Search FAQs Links Jobs Whitepapers MVPs
machtus (TechnicalUser) 25 Jan 03 12:12
How setting network connection on NIU?
mdfan (IS/IT--Management) 25 Jan 03 14:19 Do you mean defining IP address for the NIU board or do you mean establishing a connection to external server application like DNA or external client application like CCM ?To set IP address use : IONPI:IP=,MASK=,..... (see alex for details)To setup connection to external server/client useIONCI:.....; (also in ALex)
Hope this helps .
lalrl (TechnicalUser) 25 Jan 03 17:45 sorry, duvel
not ionpi but ionpc
in detail (if NIU is not System-NIU or not already installed, it must be initiated first with cnhui: bpos=x-x-xx; and then iobpi:bpos=x-x-xx,node=yyy):ionpc:equ=x-x-xx-4,ip=,gate=,mask=;if not accepted maybe first:ioeqi:equ=x-x-xx-4,iodev=yyyy,type=network,usage=mml;
y = free characters
mdfan (IS/IT--Management) 26 Jan 03 3:41 Thanks lalrl , you are absolutely right . I must have been in a hurry. This command has only a change command instead of initiation command.Anyway it is good that this forum is consisting of so obervant and updated people.
machtus (TechnicalUser) 26 Jan 03 8:39 Thanks all but I send command:ionci:iodev=telnet,ip=192.168.1.7,rport=23,user=fiol;
and Pbx report NOT ACCEPTEDIODEV NOT APPLICABL
what is wrong
mdfan (IS/IT--Management) 26 Jan 03 9:23 The example you try indicate for instance that you want to define a GICI link towards a DNA server. Then there are following issues to invoke :1) The iodev used must have been defined with IOEQI , check with IODDP;In addition , if used for anything else than MML , USAGE parameter of IOEQI should say OUT.2)rport is the TCP port talking to the server , this must be configured the same on the server side.3) user should be identical to predefined user names. If using DNA , use GICI-x (x=1,2,3 etc.) , if using CCM use user=mis ( I think) and if using applicationlink use user=CSTA (I think) . Check ALEX for this.
Hope I did not miss out anything.
HOW DO I KNOW HOW ROUT IS FOR ONE
BOARD?thread806-442112Share This Forum Search FAQs Links Jobs Whitepapers MVPs
Check Out Our Whitepaper Library. Click Here.enlace1 (Programmer) 7 Jan 03 20:09 IF I HAVE SEVERAL ROUTS I LIKE TO KNOW, HOW CHOOSE ONE ROUT FOR ONE DID
lalrl (TechnicalUser) 8 Jan 03 16:42 with opcts you link the rou and the did (oacc) together with calt=7 (public lines). And if you establish a new corg, than you must use opcgs additionally. Check with opctp and opcgp
fellicciano (TechnicalUser) 26 Jan 03 15:59 I DON`T KNOW IF I UNDERSTOOD IT WELL,BUT IF I WANNA SEEAN ROUTE EQU I TYPE THE COMMAND SYEDP:ROU=XX,TRU=ALL;
FICRI (TechnicalUser) 27 Jan 03 2:37 If you know the route number the command to see its EQUs is ROEDP:ROU=,TRU=ALL;
ulhaq (TechnicalUser) 27 Jan 03 3:34 could exactly get the base question ??????
md110bc10 (TechnicalUser) 29 Jan 03 6:11 IF U DODT KNOW THR ROU NO TYPE RODDP:DEST=ALL;U WILL GET THE ROU NO AND THEN ROEDP:ROU=XX,TRU=ALL;
Still cannot remove TLU configurationthread806-474974Share This Forum Search FAQs Links Jobs Whitepapers MVPs
DevPlan (TechnicalUser) 13 Feb 03 13:40 Hi Patcher (or someone else).Actually I didn't went thru the whole re-configuration of the TLU board since I had already removed the board and I don't have the 2-Mbit line for that board anymore.
Thus I give you the missing data and I hope, you see some way how to remove the board configuration.============================================================
AUTHORITY CLASS 7 (C) COPYRIGHT ERICSSON SCIENT 13FEB03 19:05:41 1-0-60-01 SYSTERMINAL <ALLOP;ALARM LOG IDENTITY: SOLEND VERSION: LZY2035153/1/BC10CNA129/R1A
DATE: 13FEB03 TIME: 19:06:05 CLASS: 2 15 DEVICE BOARD FAULTY OR MISSINGDATE TIME ALP NOIF EQU BRDID10FEB03 17:44:23 2 1 001-0-30-00 57
END<CNBIP:BPOS=1-0-30; DEVICE BOARD REVISION INFORMATION DATE: 13FEB03 TIME: 19:06:53 BPOS BOARD/BRDID PRODUCT NUMBER REVISION STATUS ADD /IND 001-0-30 57 SYSTEM BLOCKED END<CNBOE:BPOS=1-0-30; CONFIGURATION BOARD END INDIVIDUAL STILL INITIATED ON EQU 1-0-30-00 END
<LSCNP:LIM=1;LIM SWITCH CONFIGURATION DATA LIM SIZE STATE 1 LSU 1024 OK DSU 0 256 OK DSU 1 256 OK DSU 2 256 OK DSU 3 256 NOT EQUIPPED END
<SYECP:LIM=1;SYSTEM EQUIPMENT CONFIGURATIONINITIATED LINE INDIVIDUALS IN LIM 1INTERNAL LINES: ANALOGUE 144 DIGITAL 49 CAS POTS ITS OPERATOR 1 DATA
DUALPUBLIC LINES: ANALOGUE 8 DIGITAL ISDN S0 ISDN S2M 60PRIVATE LINES: ANALOGUE DIGITAL APNSS DPNSS ISDN S0 ISDN S2MEND
<SYEDP:BPOS: =1-0-30;SYSTEM EQUIPMENT DATAEQU BOARDID TYPE DIR ROU/TRU001-0-30-00 57 - END<====================================================
patcher (TechnicalUser) 13 Feb 03 16:20 Can you do this and please can you post the whole process.
Step 1:>SACOP:LIM=1,UNIT=DCP,FILNO=3,RELOFF=06,POINT=60;If data is 02 goto step 2 if not, dont do anything.
Step 2:>SACOS:LIM=1,UNIT=DCP,FILNO=3,RELOFF=06,POINT=60,DATA=01;>YES;>CNBOE:BPOS=1-0-30;
Dump if successful.
//patcher
DevPlan (TechnicalUser) 13 Feb 03 17:16 Thanks Patcher, it looks like it worked.Here is what I did:=======================================================<SACOP:LIM=1,UNIT=DCP,FILNO=3,RELOFF=06,POINT=60; MEMORY CONTENT ON INDIVIDUAL POSITION EXE A FILE NUMBER RELOAD FILE START DS FILE START 3 0000074A POINT RELOFF DSOFF ADDRESS DATA ISO 0060 0006 00001170 02 .END <SACOS:LIM=1,UNIT=DCP,FILNO=3,RELOFF=06,POINT=60,DATA=01;
SACOS:LIM=1,UNIT=DCP,FILNO=3,RELOFF=06,POINT=60,DATA=01; SURE? (YES/NO)<Y WAIT EXECUTED <CNBOE:BPOS=1-0-30;EXECUTED<DUSYI:DUMP=CHANGES,PRINT=RESULT;ORDERED=======================================================Best regards! DevPlan
Routes ?thread806-472052Share This Forum Search FAQs Links Jobs Whitepapers MVPs
Tek-Tips Forums is Member Supported. Click Here to donate.Arnoldnt (TechnicalUser) 11 Feb 03 6:25 Hello people !
Does anybody know how to do this.
There is a sequence of keys you can press before making a call to 'force' the call to go over certain routes....
Anybody got any ideas as to how to figure these out ?????
Any help will be great.
Arnoldnt
FICRI (TechnicalUser) 11 Feb 03 6:33 Could you be a bit more specific?Is it a call to a private network or is it public call you refer to?Do you use LCR (Least Cost Routing)?
Isinor (Instructor) 11 Feb 03 8:42
Hi, this is close to it... I think from memory...*FC* individual line number # route access code + external number
E.g. *0*01#90012129763838
Gets TRU 01 in DEST 9 Dials 001212...
You can also do this from digital extensions.
m110d (TechnicalUser) 11 Feb 03 11:28
The following is an example of the procedure.
Let's say you have ROU=22 with 10 trunks in LIM 5 and 20 Trunks in LIM 6 and the access code is 0. To test individual trunks in each LIM you dial
*0*501#0number *0*(ind trunk select)501(LIM 5 TRU 01)0(DEST assigned to route)number(rest of digits)*0*502#0number*0*503#0numberand so on until*0*510#0number
*0*601#0number*0*602#0numberand so on until*0*620#0number
It is the DEST that selects the route. A point to note is the DEST must be the default assigned to the route, this will not work for CHO.Hope this helps
RODAP and COMMAND LOSTthread806-486868Share This Forum Search FAQs Links Jobs Whitepapers MVPs
spacer73 (IS/IT--Management) 27 Feb 03 6:22 SysInfo:BC11SP10, 5 LIMs, TLU80/1 (E&M, TLP22)
ROCAI:ROU=40,SEL=012000000000001,SIG=411110000000,TRAF=00151515,TRM=4,SERV=3100000001,DIST=030,DISL=128,NODG=0,BCAP=001100;RODAI:ROU=40,TYPE=TL22,VARI=00012000,VARO=04F11000,VARC=010F0002,FILTER=NO;ROEQI:ROU=40,TRU=3-1,EQU=3-1-52-00;ROEQI:ROU=40,TRU=3-2,EQU=3-1-52-01;ROEQI:ROU=40,TRU=3-3,EQU=3-1-52-02;
<RODAP:ROU=40;ROUTE DATAROU TYPE VARC VARI VARO FILTER WAITWAITWAITCOMMAND LOST
What is this? Message "COMMAND LOST" present only with option "TYPE=TL22". If I send comvand RODAI:TYPE=TL22 system say:
<RODAI:ROU=81,TYPE=TL22,VARI=00012000,VARO=04F11000,VARC=010F0002,FILTER=NO;NOT ACCEPTEDTYPENOT IN RANGE
What is this? Please help me!
Andy
P.S. With another unit (TL11,TL37, SL60) all work fine. RFEXI can't solve this problem.
dognbone (Programmer) 27 Feb 03 16:20 It sounds like you don't have the program unit TLP22 in the system. Try doing this:
CNPIP:UNIT=TLP22;
This will tell you if the unit is loaded in the system and in which LIM's.
GioBs (TechnicalUser) 27 Feb 03 16:32 HiI agree with dognbone, probably TLP22 is missing in your MD110, but this not justify the COMMAND LOST.Which was the system answer at ROEQI:ROU=40,... command?
Bye GioBs
spacer73 (IS/IT--Management) 27 Feb 03 20:40 Hi, dognbone and GioBs!
<CNPIP:UNIT=TLP22;
PROGRAM UNIT INFORMATION PU-NAME PU-NO PRODUCT NUMBER REV PATCH TLP22 H'39C 4/CAA 111 8765/011 R5A YES TYPE B'0000 0000 0000 0000 0001 0011 1000 0000 TYPEEXT B'0000 0000 0000 0000 1110 0000 0100 1011 LOADED IN LIM 1 2 3 4 5 END
<ROEDP:ROU=40,TRU=ALL;ROUTE EQUIPMENT DATAROU TRU EQU SQU INDDAT CNTRL 40 003-1 003-1-52-00 40 003-2 003-1-52-01 40 003-3 003-1-52-02
END
TLP22 present in system, all call over this route work fine , but not working command RODAP:ROU=40;
Andy
spacer73 (IS/IT--Management) 27 Feb 03 21:08 For more information:
<HIREI;
WAITEXECUTED<RODAP:ROU=40;ROUTE DATAROU TYPE VARC VARI VARO FILTER WAITWAITWAITCOMMAND LOST <HIMDP;
DIAGNOSTICS FROM OPERATING SYSTEMTIME DATE09:04:44 28FEB03DIAGNOSTICS FROM LIM 001
TIME DATE ERROR CODE09:03:35 28FEB03 H'14JUMP TO ILLEGALSTATELOGICAL PROGRAM ERROR ADDRESS = 02021FD6ENTERSWSW B-LEVEL SIGNAL PROK (H'005B)FROM OCM (H'017) EXE A IN LIM 001TO THH (H'3CC) EXE A IN LIM 001NUMBER OF DATA BYTES IN SIGNAL = 7 WITH 0 1 2 3 4 5 6 7 8 9000 04 02 6D 09 0C 00 17STACK ADDRESS = 00000000SIGNAL SEND ADDRESS = 0200367C
USER STACK DUMP 0 1 2 3 4 5 6 7 8 9 A B C D E F02 01 55 B8NO INFORMATION STORED IN LIM 002NO INFORMATION STORED IN LIM 003NO INFORMATION STORED IN LIM 004NO INFORMATION STORED IN LIM 005
END
Andy
spacer73 (IS/IT--Management) 27 Feb 03 22:35 Hi, All!
Problem fixed! I'm restart all PU in station with command SFCEI; All units in system working very fine.
Thanks for All, who helped me with my problem.
Andy
SPONTANEOUS RINGING OF ANALOG EXTENSIONSthread806-480426Share This Forum Search FAQs Links Jobs Whitepapers MVPs
kings1 (TechnicalUser) 20 Feb 03 5:02 Hello,
We have a 9-lims system running on BC11 SP8. Sometimes all analog extensions in one specific lim are spontaneous ringing. We can solve the problem by restarting all ELU29 in the Lim. A restart of PU ELP6 doesn't help.
Does someone know a solid solution for his problem?
kings1 (TechnicalUser) 27 Feb 03 4:51 Does nobody seen this problem before??
Hope that somebody know anything!!
Kings
spacer73 (IS/IT--Management) 27 Feb 03 6:43 Hi, kings1!
1. What analog phones working on your system?
Old model of "Panasonic" with long hookflash? I'm right, see ASPAP:PARNUM=253; I have PARVAL=120 (600ms).
2. You have VoiceMail on system? If right, then user has message in mailbox.
3. Sorry, I don't have this problem on me system a long time. I don't know what I help you any more.
Andy
ulhaq (TechnicalUser) 28 Feb 03 0:32 Hi
what revison of ELU-29 cards u have
is this an upgraded MD110
regards
kings1 (TechnicalUser) 28 Feb 03 1:45
Hello,
It's an upgrade MD110 from BC9 to BC11, but the lim's who have this problem are new consono's. The old /50 are replaced with the upgrade. The ELU29 have revision R9H. I don't know what kind of analog phone are used over there.
Hope you have enough info. If not let me know.
Kings
enktr (TechnicalUser) 28 Feb 03 9:28 Hello everbody,
We have 1 lim BC 11(SP8) system.We have the same spontenously ringing problem.But it doesn't change accordingto the firmware revisions of ELU-29 boards.Some of them are R8A and the others are R9H.This problem is not on thespecific boards.We have this on the all ELU-29 boards.not atthe same time.But some times 1 board sometimes 2 boards on the system can make this problem simultaneously.Swapping the boards doesn't help.
If anyone can share the solution.We will appreciate....
rrmagno (TechnicalUser) 2 Mar 03 4:56 I do have the same problem with my system, 5 LIMs and sometimes 1 or 2 individuals of ELU29 will rong spontaneously,restarting the board will resolve the problem. I Do have Philips telephone sets, ELU29 R4C in my BC9.
ulhaq (TechnicalUser) 3 Mar 03 0:29 I think you guys have the same problem as we had.Probably u need to approach Ericsson guys near you, this usually happens with induction in the OSP and high traffic rate, the solution is a firmware change on ELU29's.
Are you sure that the your Equipment is propoerly grounded and OSP is not affected with in kind of induction and transient voltages???
regards
fcpli (TechnicalUser) 5 Mar 03 16:43 Hi!
Are you sure that you do NOT have MEW or MMW functionaltyon these phones?The problem described above has NOTHING to do with the FW/SW, I mean that this is tested in the lab environment so many times that it is NOT possible! Also it has nothing to do with the RG board, - no way!!!! (the RG can not send sporadeuos ring to random pointer, eg. a phone!).If everything seems to be OK, and no ALLIP or HIMDP is shown concerning this matter, then you have a mechanicalproblem (task). Hope this answer helps you further.
kings1 (TechnicalUser) 7 May 03 2:03 On the knowledge base from ericsson is reported about this problem at the end of april. ELU29/11 R9H are affected with this problem and have to be downgraded to R8H.
You can order new eprom for the ELU29/11 on the knowledgebase from ericsson or contact your local service partner.
md110user (TechnicalUser) 7 May 03 11:32
Hi I face the Same Problem and by downgrade From R9H/11 to R8H, the Problem has been solved
Don't want an analog extension to dial 0 to make an external callthread806-541940Share This Forum Search FAQs Links Jobs Whitepapers MVPs
Check Out Our Whitepaper Library. Click Here.baldanondo (TechnicalUser) 5 May 03 12:49 Hello,
We need to configure an analog extension so that we can make external calls from it without needing to dial previously a 0 to get the dialling tone.
Is it possible to configure it? How?We have BC-11
Thank you
hotfix (TechnicalUser) 5 May 03 15:50 You only have do an special purpose on the extension:SPEXI:DIR=XXXX,OPT=N,NDC=0; where NDC are "none dialled connection".Best regards, Hotfix
Looking for help with Tie Line between MD110 and Cisco ICSthread806-571987Share This Forum Search FAQs Links Jobs Whitepapers MVPs
SLonge (IS/IT--Management) 10 Jun 03 9:17 Hey all, I'm working on connecting our Ericsson MD110 to a Cisco ICS. I'm not sure what card to use in the Ericsson however, I was thinking of using a TLU77/1, but I'm not sure if this is the best choice. We're on BC8, any help that you could offer would be greatly appreciated. Additionally, I was wondering exactly how one adds a card to the MD110. I know where the card goes, but I'm not sure how to initiate the card into the system. I've done plenty of MD110 administration, but never added a card on my own. I'd really appreciate any help that you are willing to offer.
Thanks,Steve
Isinor (Instructor) 10 Jun 03 10:25 Hi SLonge,
There are a few steps required…1. Insert card & run cable, then Add HW to MD1102. Ensure appropriate PU’s are on the MD110 (programs)3. Program Route
I can help with a bit of your question… How to add HW to the MD110…1. Find a free BPOS with enough Time Slots (24 I think for a TLU77) you might find using CNLIP:LIM=X,DEV=YES; helps a bit.2. Insert Card and cable. (Note: you will need to use a BPOS such as 1-1-10 or 1-1-20 as they will have 32 Time Slots)3. CNHUI:BPOS=X-X-XX;4. Wait a few sec’s then just do a ‘;rtn’ then one more ‘;rtn’ you should get new hardware found and then new hardware updated.5. CNLIP again to see if the HW is ‘Passive’
Then you can start to do the route programming…
timucin75 (TechnicalUser) 10 Jun 03 10:52 What kind of a hardware is this ICS ? A gateway ? router ? What is the specific ( in Cisco terminology) hardware that the MD will be connected to ??
SLonge (IS/IT--Management) 10 Jun 03 11:13 The ICS is "Integrated Call System" Cisco's new turn key PBX solution. The MD will be connected to a T1 PRI voice interface on this system.
Thanks for all your help!
Steve
External - Internal Distinctionthread806-579233Share This Forum Search FAQs Links Jobs Whitepapers MVPs
enktr (TechnicalUser) 18 Jun 03 5:14 hi all,
we have MD110 BC11 Sp10 2 lims, When an internal calls an intenral and transfer an external call, we recognize this as an internal call (although it is an external). so the last two digits of CDIV (011151311) Don't work. by the way, even though the call is an external, this call is analysed as an external call.
what can we do about this problem?
Best Regards....
fcpli (TechnicalUser) 18 Jun 03 8:37 Actually cdiv doesn't follow the transfer case, just diversion. You have to use ADC parameter (extension) in order to get the authority working, and then e.g. with TCMASdecide, who is allowed to transfer external calls.
Class of servicethread806-573008Share This Forum Search FAQs Links Jobs Whitepapers MVPs
Hitechbuzz (TechnicalUser) 11 Jun 03 6:48 Hi Guys I wish to set up a class of service that will allow local calls and national calls but not cell or pager.Local could be anything 1--9 national will be 01xx.03xx,04xx,06xx,07xx,09,freephone would be 0508xx or 0800xx,calls I wish to bar are 02xx can you please give details,many thanks Hitechbuzz.
Isinor (Instructor) 12 Jun 03 10:45
Hi Hitechbuzz,The following example is how you could do close to what you want… but starting as thought it was a new system. (You will have to adapt it to suit your existing setup)
The MD110 uses allowed numbers lists to control outgoing calls, so you do not bar calls as such… you just allow all appropriate numbers… The lists are called CDCAT’s ‘Call Discrimination Category’ you can have up to 15 of them.
You need to have a plan, such as…CDCAT 0 is the most restricted local and free calls CDCAT 1 is local & national but not cell or pagerCDCAT 2 is local & national & etc…
I would recommend you keep this as simple as you can. Use only the CDCATS that you really need! Since you do not say what access code is used for external access this example assumes 0 for PSTN access.
To Print the existing CDCAT’s…NADAP:NUMTYP=CD;
To Add numbers to the allowed list…NACDS:CDCAT=0&&2,NUM=01&02&03&04&05&06&07&08&09&00508&008; // Local calls & free 0800//NACDS:CDCAT=1&2,NUM=001&003&004&006&007&009; // National calls //NACDS:CDCAT=2,NUM=000; // International Calls //
Note that the solution may have several issues to be resolved… e.g. what happens if someone dial 0509xx ? the example will ‘bar’ that call as it is not in the allowed list!
To remove numbers from the allowed list…NACDR:CDCAT=0,NUM=03&09;
That’s part one, you have allowed number lists called CDCATS. Next you need to attach an extension or several extensions to these lists… as normal on the MD there is more that one possibility… You do not say what BC release so this is BC9 ish…
You could set up a new Common Category (CAT)… This example only deals with the ‘CDCATS’ bit of the CAT… Find a Free CAT... EXCCP:CAT=ALL; (any that is all 000000)
EXCCS:CAT=1,TRAF=xxNNDDxx,SERV=xxxxxxxx,CDIV=xxxxxxxxx;
Where NN is the CDCAT for Night time and DD is the CDCAT for day time… The CDCATS are always referred to as a two digit value in TRAF (NACDS = 00, 01, 02 to 15) e.g. EXCCS:CAT=1,TRAF=03000215,serv=0212107,CDIV=011150000;
Then change the extensions to match this Common Category (CAT)...EXCAC:DIR=xxxx&yyyy,CAT=1;KSCAC:DIR=xxxx&yyyy,CAT=1;
This process is detailed in Alex and is part of typical TTY admin courses... it’s not that easy and potentially problematic… good luck
RegardsIsinor
Hitechbuzz (TechnicalUser) 12 Jun 03 20:43 Thanks IsinorI have looked at NADAP:NUMTYP=CD;and got a long list with numbers on the left then on the right CAT with 7 6 5 4 3 2 1 opposite. 6 seems to be international,5 national,3 cell,2 local. I also use 1 to access PSTN so NACDS would read
NACDS:CDCAT=9,NUM=11&12&13&14&15&16&17&18&19&101&103&104&106&107&109; // National calls & local but not free phone or international.
I see 7, 8, &14 are in the print out.I also did a EXCCP:CAT=all & got alist of CAT's 0- 63these tie in with the Cat Cos I use on extensions.Then would EXCCS:CAT=54,TRAF=xx0909xx,SERV=xxxxxx,CDIV=xxxxxx;I get frustrated with Alex trying to find any thing.does that make sense.Thank you for your helpBrian
Hitechbuzz (TechnicalUser) 30 Jun 03 18:38 Thanks IsnorI took the plunge did printouts of NADAP'S& EXCCP had 60+ of them went through the Number analysis tables added another Cat 13 to them & added in EXCCS 54 crossed fingers. Have done some testing and all seems well seems to do what I wanted did a Dusyi & sync last night.So thanks once again. 2 stars for your helpCheers Brian
Delete of routethread806-593165Share This Forum Search FAQs Links Jobs Whitepapers MVPs
CIF (TechnicalUser) 3 Jul 03 9:00 I have a multi LIM system running on BC11/sp7.I want to remove a route but giving the command ROEDP:....I get the message: trunk is busy but, the trunk is already physically removed.
There is no traffic whatsoever.
Regards Andy Lemmens.
ButtonIt (Vendor) 3 Jul 03 11:17 You are probably getting this message because you have disconnected the circuit and the switch has blocked it. The first thing to try is re-connecting the circuit and then ending it.
Why are you using ROEDP to end route? Do you mean ROUTE?
Vanersborg (IS/IT--Management) 9 Jul 03 10:28 Hello
You have an pointer missmatch in in your system.Not an easy thing to handle. But try to restart SLP60, TLP60(if thats the type of route you are using).If this dosn't help, you must consult an expert........
rrmagno (TechnicalUser) 10 Jul 03 8:04 Try to end the equipment that is being used by your route. Remove any destinations that are tied to your route. Try also to block the board before ending equipments. Good luck!!!
2 ext. link and different routing for 2 numberthread806-606567Share This Forum Search FAQs Links Jobs Whitepapers MVPs
149149149 (TechnicalUser) 18 Jul 03 7:49 I have 2 external links into national provider . I want in order that all connection go across first external link(dial 0), but only town policy go across second external link(dial 0156).
This is first ext.link:<roddp:dest=0;EXTERNAL DESTINATION ROUTE DATADEST DRN ROU CHO CUST ADC TRC SRT NUMACK PRE0 20 0005000000000250000 0 1 0 99 1 0005000000000250000 0 2 0
How make this second ext.link? Is correctly this?EXTERNAL DESTINATION ROUTE DATADEST DRN ROU CHO CUST ADC TRC SRT NUMACK PRE0156 99 0005000000000250000 0 2 0 20 1 0005000000000250000 0 1 0
whosrdaddy (Vendor) 18 Jul 03 9:19 your solution will not work.
here's a straigth forward solution ...
make a new destination , let's take 99 for example :NANSI:NUMSE=99,NUMTYP=ED; (change 99 into something else if this number series is already assigned)RODDI:DEST=99,ROU=99,ADC=0005000000000250000,SRT=3;add some pseudo LCR :LCDDI:TAB=ENT,ENTRY=00156,TRC=1,PRE=99;
this will convert the dialled number 00156 into 990156 which is dest for your second link (route 99)
greetings,http://www.damovo.com
QuiltedCamel (MIS) 18 Jul 03 9:25 Would you not be better doing this through LCR ?
If you first initiate a destination for local calls (8000) and another for national calls (8001) with those parameters but changing the TRC & SRT figures to 4 & 5
Then populate your LCR tables something like:
LCDDI:TAB=FDT,FRCT=1,TZONE=1,PRE=8000;LCDDI:TAB=FDT,FRCT=2,TZONE=1,PRE=8001;
LCDDI:TAB=DNT1,ENTRY=0156,FRCT=2;This sends yout local traffic over Fictitious Route 2 which is destination 8001.
Anything that doesn't match the "0156" will fall through to DNT2
LCDDI:TAB=DNT2,ENTRY=0,FRCT=1;Will send it all to Ficticious Route 1, which is destination 8000.
Of course none of that will work unless you have your least cost routing access digit set (to '0') which you probably won't be able to do if '0' is used as part of a route selection digit.
rorni (IS/IT--Management) 18 Jul 03 9:43 HiYou need to use LCR feature :(backup first !)
first, change route access code to free "0":nansi:numse=XX,numtyp=ed;nansi:numse=YY,numtyp=ed;roddi:dest=XX,rou=20,srt=2,adc=...;roddi:dest=YY,rou=99,srt=2,adc=...;
Second, set LCR nanse:numse=0,numtyp=ed;nansi:numse=0,numtyp=lc;
lcddi:tab=fdt,frct=1,pre=YY;lcddi:tab=dnt1,entry=0156,trc=1,fdt=1;
lcddi:tab=fdt,frct=2,pre=XX;lcddi:tab=dnt2,entry=0,trc=1,fdt=2;
Good luck/rorni
Analogue internet connectionthread806-608449Share This Forum Search FAQs Links Jobs Whitepapers MVPs
kevxh (Programmer) 21 Jul 03 10:49 A client of mine needs to make an analogue internet connection, the modem will dial and begin handshake, handshake fails and line is dropped.
Don't know what to do, can anyone suggest anything?
mdfan (IS/IT--Management) 21 Jul 03 12:54 Check first IOIFP if Baudrate is set to all.
lancbomb (TechnicalUser) 21 Jul 03 14:52 ericsson dont support baudrate above 28800 on ana analogue extn so try dropping ypur baudrate
jay944 (TechnicalUser) 22 Jul 03 8:29 kev,
assume, ordinary ana ext, trying to dial out using a modem,
ok basics
1> scexp, make sure there is no clock slip2> can other people dial out ok via modems3> have you tried this modem on another ana port
holla back with this infomation and will try and help
kevxh (Programmer) 23 Jul 03 7:03 Thanks Jay.
1 - No clock slip2 - Yes3 - Yes
It seems that the internet connection is made, but connection to our jserver for applet download is the source of the failure. The internet connection stays up, just the jserver connection drops. Other internet stuff works fine.
It's a laptop that's being used and when it's taken off to a another site with an analogue line it works fine. No settings are changed.
jay944 (TechnicalUser) 23 Jul 03 8:47 hi,get another laptop, connect it to this port, dial into an isp etc does that fail as well ?
kevxh (Programmer) 25 Jul 03 3:32 Hi Jay,
Have tried another machine/modem, same thing. The actual connection is working fine, on any modem. The problem is a specific site that uses java to connect to a secure server, it's the secure login that fails.Works outside on a normal analogue connection but not on site over the digital.
Sorry i didn't mention this lot before, only just found out myself.
Kev
haja (TechnicalUser) 29 Jul 03 3:53 Hello,Can somebody tells me what i do wrong by making a safety backup. We have a 38 lim system on BC11 sp 7.
<BLEQI:EQU=1-0-50-00;EXECUTED<IOSII:IODEV=SAFE-DSK,NODE=SYSN,SIPOS=0,SUBFS=SAFETY-FS;EXECUTED <FICRI:SUBFS=SAFETY-FS,SIZE=64;FICRI:SUBFS=SAFETY-FS,SIZE=64;SURE? (YES/NO)<Y;EXECUTED <BLEQE:EQU=1-0-50-00,ALLFM=YES;EXECUTED
<DUBDP;BACKUP DATAEXTERNAL BACKUP LATEST PREVIOUS REL1 REL2 05:00 28JUL03 05:00 27JUL03LOCAL BACKUP NO LIM WITH DIVERGENT TIME AND DATE END
<FISBI:DIR=REL1,SUBFS=SAFETY-FS;FISBI:DIR=REL1,SUBFS=SAFETY-FS;SURE? (YES/NO)<Y;ORDERED <FISCP:IODEV=SAFE-DSK; FILE SYSTEM CAPACITY DATATOTAL DISK SPACE: 2067 MBYTESSUBFS: SAFETY-FSKBYTES FILESTOTAL AVAIL TOTAL MOUNTED65536 - 19200 - END SPONTANEOUS PRINTOUT
SAFETY BACKUP RESULTCOPYING TO SAFETY BACKUP FAILEDSUBFILE SYSTEM IS FULLEND
greatingHans
safety backupthread806-615701Share This Forum Search FAQs Links Jobs Whitepapers MVPs
haja (TechnicalUser) 29 Jul 03 4:00 Hello,Can somebody tells me what i do wrong by making a safety backup. We have a 38 lim system on BC11 sp 7.
<BLEQI:EQU=1-0-50-00;EXECUTED<IOSII:IODEV=SAFE-DSK,NODE=SYSN,SIPOS=0,SUBFS=SAFETY-FS;EXECUTED <FICRI:SUBFS=SAFETY-FS,SIZE=64;FICRI:SUBFS=SAFETY-FS,SIZE=64;SURE? (YES/NO)<Y;EXECUTED <BLEQE:EQU=1-0-50-00,ALLFM=YES;EXECUTED
<DUBDP;BACKUP DATAEXTERNAL BACKUP LATEST PREVIOUS REL1 REL2 05:00 28JUL03 05:00 27JUL03LOCAL BACKUP NO LIM WITH DIVERGENT TIME AND DATE END
<FISBI:DIR=REL1,SUBFS=SAFETY-FS;FISBI:DIR=REL1,SUBFS=SAFETY-FS;SURE? (YES/NO)<Y;ORDERED
<FISCP:IODEV=SAFE-DSK; FILE SYSTEM CAPACITY DATATOTAL DISK SPACE: 2067 MBYTESSUBFS: SAFETY-FSKBYTES FILESTOTAL AVAIL TOTAL MOUNTED65536 - 19200 - END SPONTANEOUS PRINTOUT
SAFETY BACKUP RESULTCOPYING TO SAFETY BACKUP FAILEDSUBFILE SYSTEM IS FULLEND
greatingHans
rorni (IS/IT--Management) 29 Jul 03 4:16 Hi
38 Lim is a really big system !I strongly suspect that 64 MByte is not enough to copy all data.You may check this by checking space on the main hard disk :"fiscp:iodev=sysdisk1;"Space required = used space USR1 + S2 +S3+...
You better to do safety using MDDT via NIU board
Hope this help/Rorni
jay944 (TechnicalUser) 29 Jul 03 5:06 Rorni is right,big systems you need to split the fisbi
haja (TechnicalUser) 29 Jul 03 5:08 Hi RorniThis is the result of fiscp.<fiscp:iodev=sysdisk1; FILE SYSTEM CAPACITY DATATOTAL DISK SPACE: 2067 MBYTESSUBFS: SYSSUBFS11KBYTES FILESTOTAL AVAIL TOTAL MOUNTED64512 21717 19200 /SYSN/USR1 SUBFS: SYSSUBFS12KBYTES FILESTOTAL AVAIL TOTAL MOUNTED64512 10398 19200 /SYSN/USR1/SES/DR/REL1/S2 SUBFS: TMFSKBYTES FILES
TOTAL AVAIL TOTAL MOUNTED64512 26619 19200 /SYSN/USR1/ACS/TM END <fiscp:iodev=sysdisk2; FILE SYSTEM CAPACITY DATATOTAL DISK SPACE: 2067 MBYTESSUBFS: SYSSUBFS21KBYTES FILESTOTAL AVAIL TOTAL MOUNTED64512 24549 19200 /SYSN/USR2 SUBFS: SYSSUBFS22KBYTES FILESTOTAL AVAIL TOTAL MOUNTED64512 8995 19200 /SYSN/USR2/SES/DR/REL2/S2 END
Both disks are also 64 MB
Hans
haja (TechnicalUser) 29 Jul 03 5:17 Hi Jay944,Can jou help me with te commands ?Hans
rorni (IS/IT--Management) 29 Jul 03 8:17 Ok,
You need a storage of :
SUBFS: SYSSUBFS11KBYTES FILESTOTAL AVAIL TOTAL MOUNTED64512 21717 19200 /SYSN/USR1 SUBFS: SYSSUBFS12KBYTES FILESTOTAL AVAIL TOTAL MOUNTED64512 10398 19200 /SYSN/USR1/SES/DR/REL1/S2
2*64512 - 21717 -10398 = +/- 90 MB which is biiger than the max size (64 M), so you need to split your safety.I've seen a procedure to do that. I will send it to you/rorni
haja (TechnicalUser) 29 Jul 03 8:31 Thanks rorni,I will wait for your reply.
hans
haja (TechnicalUser) 4 Aug 03 4:37 My e-mail adress is [email protected]
rorni (IS/IT--Management) 4 Aug 03 11:14 Hi
Try this.
Regards/rorni
IOSII:NODE=SYSN,IODEV=SAFETY,SIPOS=0,SUBFS=SAFETY-SF11&SAFETY-SF12;ficri:subfs=safety-sf11,size=xx;y;ficri:subfs=safety-sf12,size=xx;y;fimoi:subfs=safety-sf11,path=/sysn/usr3;fidii:path=/sysn/usr3/ses;fidii:path=/sysn/usr3/ses/dr;fidii:path=/sysn/usr3/ses/dr/rel1;fidii:path=/sysn/usr3/ses/dr/rel1/s2;fimoi:subfs=safety-sf12,path=/sysn/usr3/ses/dr/rel1/s2;fifoc:path=/sysn/usr3/ses/dr/rel1,owner=dr;ficpi:spath=/sysn/usr1/ses/dr/rel1,path=/sysn/usr3/ses/dr/rel1,coop=dir;
jay944 (TechnicalUser) 4 Aug 03 11:39 hey haja,I am "son of jan" ???
if were on the same wavelength !
haja (TechnicalUser) 5 Aug 03 8:04 Hi Rorni,
Everything works well,
thanksHans
Connect fixed Analogue number to a TLU75?thread806-625550Share This Forum Search FAQs Links Jobs Whitepapers MVPs
mdboy (TechnicalUser) 8 Aug 03 8:12 Hi,
I have a fixed number from the phonecompany (Sweden) and I want to connect my MD110 directly to that number so I can use the phones in my MD110 instead of plugging in a normal phone in the outlet. I have tried different parametres (dont have them right now) and I dont get it to work.
When I call from the MD I have to dial 00 and that should be the same as going offhook on the TLU75 meaning I would get dialtone on the fixed number from Phone Company. Then I just dial the number I want to call.
Hopefully you guys can help me with this since this is really bugging me. I havent tried this for a couple of months now but I found this link again and I thought I might give it a try :)
/Mdboy
00151515 (TechnicalUser) 9 Aug 03 1:11 Print this:
RODDP:DEST=00;
now look what is the ROU being used by this DEST and print
ROEDP:ROU=X,TRU=ALL;(where X being the route for DEST of 00)
now initiate this board using CNHUI.Check it by CNLIP if it is already initiated, next is to initiate equipment for Route X using ROEQI. But first let us see what you've got on the print-out and we'll see what we can do. Maybe we'll have to initiate a new route for your TLU75....
Kressmark (Instructor) 11 Aug 03 18:52 Hi,
Are you running the Swedish AS (Application System) in your MD110?
I think it is needed to get the TLU75 to work properly.
/mk
megglesfield (TechnicalUser) 13 Aug 03 2:12 The TLU75 works in the Standard AS, Saudi AS Export AS as well as Swedish to my experience. I am presently using TLU 75 in a similar manner.Here are the RODAP and ROCAP on the route I have set up.<rodap:rou=12;ROUTE DATAROU TYPE VARC VARI VARO FILTER 12 TL11 H'00000012 H'00000108 H'00002815 NO
END <rocap:rou=12;ROUTE CATEGORY DATAROU SEL TRM SERV NODG DIST DISL TRAF SIG BCAP12 711000000000001 4 3110100000 0 5 50 01050514 100011000000 001111
ENDYour RODDI, would then be:
RODDI:DEST=00,ROU=12,SRT=3;
ME
00151515 (TechnicalUser) 13 Aug 03 2:56 what happened to mdboy? have'nt heard from him...
total number of Trunklines in our MD110 B.C. 9.0thread806-621897Share This
Forum Search FAQs Links Jobs Whitepapers MVPs
melmj (TechnicalUser) 5 Aug 03 6:18 Hey Guys can anybody teach me how to count the total number of trunklines in our existing EPABX MD110 BC 9.0? Our Tel. Exchange administrator who installed our system died of cancer and he didn't left any documentation. We are about to begin a feasibility study for expansion and I can not determine the total number of trunklines. I can see we have these TLU44 and TLU23 cards does this mean anything to you? Is there anyway we can determine which trunklines are currently being used? Sorry about these absurd questions but I am new to this PABX system and worst of all I am tasked to continue the improvements and maintenance of this telephone system. Any suggestions, manuals or procedures that maybe sent to me will be of very much help and will be greatly appreciated. Thanks in advance. and More Power to All of you GUYS!!!
mdfan (IS/IT--Management) 5 Aug 03 6:36 Try first ROEDP:ROU=all,TRU=all;
This will give you all ext lines and which route they belong.
rrmagno (TechnicalUser) 5 Aug 03 9:07
Try also SYECP; It will tell you how many individuals are initiated in your system as well as Internal,Public and Private lines ie. Analogue, Digital, APNSS,DPNSS,ISDN, etc. etc..
cheers!
teletech (TechnicalUser) 17 Aug 03 9:14 TRY SYEVP:TYPE=TL11; Which will tell you how many analogue trunk vaccancies are there.
MD110 & Video Conferencingthread806-640600Share This Forum Search FAQs Links Jobs Whitepapers MVPs
Tek-Tips Forums is Member Supported. Click Here to donate.gibbo110 (TechnicalUser) 28 Aug 03 6:40 Can the md110 with bc11, be used for video-conferencing?I've seen reference to it in various Ericcson brouchers but am unable to confirm any facts.
Thanks
mdfan (IS/IT--Management) 29 Aug 03 15:36 You could install ELU26 which includes 4 x BRA 's .This is enough capacity for video conferencing.
dnaserver (TechnicalUser) 29 Aug 03 20:31 You can also program ELU28 to be ISDN line.2 BRIs (2 ISDN lines)are still ok ( 2 X 128kbps). The more ISDN lines you are using for video conferencingthe more cost you should invest.
Other equipment required are Ericsson NT (console)equipmennts boxes.
PABX MD110 shutdown procedures /tipsthread806-639225Share This Forum Search FAQs Links Jobs Whitepapers MVPs
dnaserver (TechnicalUser)
26 Aug 03 22:10
hello,
is there anybody knows the shutdown procedures for MD110 (BC9). Our premises always have monthly power shutdowns.Everytime when electrical power resumes back, at least one of power cards will be corrupted/faulty.
ammartins (TechnicalUser) 27 Aug 03 0:30 The PU4-DC cards manufactured in 1994/95/96, have a problem.Ericssson made a Recall to replace this cards.Contact your supplier.
dnaserver (TechnicalUser) 27 Aug 03 1:59 thankss... but how about the procedure to shutdown and switch on PABX for temporary purpose eg. due to power shutdown...
ButtonIt (Vendor) 27 Aug 03 3:37 After all backups have been completed:
1. Turn off HDU2. Turn off PU4DC/PU5DC (small blue switch on front of card) in every magazine.3. Turn off recitifiers.4. Turn off Batteries.
Just do the reverse to bring it back up again.
harddisk15 (Programmer) 27 Aug 03 7:53 Hi, It's better to switch off batteries before mains power - on power down - and switch on mains before batteries on power up.Cheers
dnaserver (TechnicalUser) 27 Aug 03 20:18 Do i need to switch off ringer card also ( if the LIM has one ringer card.)
ButtonIt (Vendor) 28 Aug 03 3:14 It is good practice to turn off the ringer card also, but you don't have to.
Remove extensionenthread806-645610Share This Forum Search FAQs Links Jobs Whitepapers MVPs
danwiking (TechnicalUser) 3 Sep 03 20:27 Hello
I need some help to remove a extension.
When i make a EXTEE:DIR=2423;
it tells me that this doesn't exist, but when i make a
EXTEI:DIR=2423,EQU=,TRM=,CAT ------
It tells me that it already exist
How can i remove this from the program ?????
whosrdaddy (Vendor) 4 Sep 03 1:51 It could be a group hunting, ACD group, Common bell group or maybe a digital extension or ....
if your system version is greater than BC7 you can do:SUDIP:DIR=2423;if it doesn't show up it must be an ACD group :ACCSP:GRP=2423;
hope this helps, http://www.damovo.com
danwiking (TechnicalUser) 4 Sep 03 2:58 no it's not a ACD or hunting group.
The problem is that the costumer has remove the extension with EMG, but something had gone wrong, because the can't make a new extension with the same number.
I had then tryed to make a new extension with winfiol,but it replyes with EXTENSION ALREADY ASSIGNED. i have then tried to make EXDDP and KSDDP, then it tells me that the extension doesn't exist.
NANSI (TechnicalUser) 4 Sep 03 3:19 Something whent wrong in EMG, that happends sometimes.You must update the EMG-database with the application MD110-Support. The extension the customer tried to remove was probably not an analog (EXDDP) or a digital (KSDDP). Maybe it was a cordless or a generic extension (CXAKP, GEDIP).
Try running a SUDIP:DIR as our daddy says.
Try to do it all from EMG if it´s possible.When the database in EMG and the MD110 are different EMG can´t handle the situation. If EMG databse thinks that extesion 1234 is free it can´t delete the extension from the MD110. If EMG thinks that extension 1234 already exist it cant add the extension to the MD110. It is vital that the MD110 and the EMG database are the same!!
NANSI
danwiking (TechnicalUser) 5 Sep 03 3:56 no no
the last it happens we made a SUDIP:DIR=xxxx
then it tells us that the DIR DOESN'T EXIST
We had E//// to Remove it.
So I think there must be some SACOP-SACOS commandthat can repair this hangup in the data,so that we can do it by our self.
danwiking (TechnicalUser) 7 Sep 03 6:24 hello
No it has nothing too do with EMG database
It's not a generic or cordless extension.
and when i make a EXDDP or KSDDP and SUDIP:DIR=XXXX it also tells me that the extension number doesn't exist.
But when i make a EXTEI:DIR=XXXX it tells me that thisextension already exist.
So there for i think that this directory number must besomewhere in the MD110 data files, and there must be away to get the info with a SACOP command from the MD110, and there must be away with a SACOS command to delete the number from the MD110.
Hitechbuzz (TechnicalUser) 7 Sep 03 21:41 Try doing Extee: Dir=2423 KSEXE:Dir=2423 Followed by NANSE:NUMTYP=EX,NUMSE=2423 & see what you get. one will give you an error just ignore it.If you do a DUSYI twice then "sync" your extension manager with MD110 support, (I usually do this at end of day as it takes time) You may clear it and bring the EMG into line with the systemCheersHitechbuzz
danwiking (TechnicalUser) 8 Sep 03 5:45 Okay
I will try it the next time i'm getting the fault.
But I don't think this will help. I still think that I have to make some SACOP - SACOS programming.
So if there are others that have a solution, then tell me please.
How to program a hot-linethread806-662914Share This Forum Search FAQs Links Jobs Whitepapers MVPs
baldanondo (TechnicalUser) 24 Sep 03 9:33 Hello,
We have BC-11 and we would like to program a analogue extension like with the hot-line functionality.
That is:
When an authorized user is going to use the phone, he will be able to call any destination.
When a not authorized user is going to use the phone, we need that the extension will ring automatically a programmed destination number and that that user won't be allowed to call any other number.
Thank you very much and regards
vdMerwe (TechnicalUser) 25 Sep 03 5:38 Hi,
Use a delayed hotline, than a person with an authorisation code can make a call and a non authorized person will be forwarded to the programmed destination.
This programming is all possible within Extension Manager
Harold
baldanondo (TechnicalUser) 25 Sep 03 5:41 Hello,
Thank you for the indications. But could you tell me which are the commands needed to program this functionality?
Regards
rfpui (TechnicalUser) 25 Sep 03 19:02 To program a delayed hotline use
SPEXI :DIR=..., OPT=D,NDC=......; Where DIR is extension numberNDC programmed destination number
And checkPARNUM=182 Length of delay time in Delayed hot-line
The parameter states the maximum time when an extension, defined as a Delayed hot-line, has to start dialling. On time out the call is automatically set up as a hotline call towards a predefined destination.
PRVAL value 2-16 in seconds
CAS Extension issuethread806-568167Share This Forum Search FAQs Links Jobs Whitepapers MVPs
tigerlow66 (TechnicalUser) 5 Jun 03 7:40 Hi,
We has an MD110 BC11SP9 system & install with CAS TLU76/3 card to external 3rd party IVR system.
Currently ,we has tested it
1. Call via hunting group internally.
2. Calling the CAS extension internally.
It work perfestly fine.Unfortunately,when i call via ISDN2 ( TLU79 ) i can hear the ringback from exchange & when i do a susip i can see that call is CALTER to the CAS ext with status BUSY.But it just stop there without going into SPEECH stage,therefore the IVR is unable to answer the call under this situration.
Can someone tell me ,is the fault lie on MD or the IVR.Is there any way to isolate it.bcos calling internally is OK.
ButtonIt (Vendor) 5 Jun 03 10:03 does your TCMAP permit them to connect to each other?
patcher (TechnicalUser) 5 Jun 03 18:27 Remember that IVR should be set properly according to A number identification. If you are calling from outside or from public you are dialling a number in MD. This number is then transferred to the IVR for analysis, if right number is received then IVR will play the right message. You need to test this IVR together with the IVR Techs. Check if integration is working properly. Test this machine properly before you introduce actual traffic. //patcher
tigerlow66 (TechnicalUser) 10 Jun 03 11:27 Patcher,
I don't understand.Bcos i use NUTRI to translate the incoming DDI number to a hunt group 198 as follow:
NUTRP;
ENTRY CNVTYP NUMTYP ROU PRE TRC 64654132 0 4 198 8
So my understanding is 63654132 is B-Number (Connected number, correct me, if i am wrong).Are u saying that the IVR (Dialogic card) has to set to recognize this B-number instead of the hunt group 198.
Thank in advance.
GASMAS (Programmer) 21 Jun 03 2:07 Hi we have same cases Ivr connected with tlu76/3 and we experienced many problems. We played around with the icat parameter of the cas extension and now no problem.Still since it works internally I would say that changing the type of number in the nutri might help.Also check that there is no rodni of this route to the ivr number.
tigerlow66 (TechnicalUser) 7 Jul 03 8:01 My ICAT==&;All other is not working.Is THERE A WAY TO TEST MAX CAS PROGRAMMING IS WORKING WITHOUT CONNECTING TO IVR.
THANK IN ADVANCE.
tigerlow66 (TechnicalUser) 7 Jul 03 8:02 SORRY THE ICAT=06 .
TripleT (Vendor) 10 Jul 03 19:50 Tigerlow66,
The problem will be that with ICAT=xxx6 the signalling pattern from the MD110 to the IVR is different for Internal and External calls. You may need to change the settings in the IVR so that it recognises both:-
0100 Internal Ring
0011 External Ring.
Otherwise as previously discussed play around with the ICAT settings to find the best match for your IVR.
Triple T
tigerlow66 (TechnicalUser) 14 Jul 03 8:07 Triple T,
Thank but i had tried & only ICAT=0006 the IVR will work with calling internally to the hunt group.
Sorry,if you happen to know the setting on IVR using Dialogic card D300 E1 PCI with globalcall,you may share with me.I am STUCK now.
TripleT (Vendor) 17 Jul 03 6:50 Tigerlow66,
Sorry I have had ne experience with that system.
However somewhere in the Dialogic Card Settings there you will be able to change the signalling pattern that the card will recognise.
The supplier / Manufacturer of the IVR should be able help you.
TripleT
GASMAS (Programmer) 30 Jul 03 1:33 If it works for internal calls try to change aspap:parnum 1to 0 . That might help.
jerommeke (TechnicalUser) 1 Aug 03 2:36 I've installed a Dialogic Board to support Genesys VTO Server and used the ICAT for IBM Direct Talk in a Dutch Application System BC9 and BC11.
Installed the Dialogic drivers without any (additional) prototcol.Could test it with a program from the disk, named "Multitest" if I remember correctly.
Worked fine only had to change the params if the application:
Ring = 0x9d6Ringing = 0x9d6OnHook = 0xfbOffHook = 0xfa
\\Jerommeke
Leonos (Programmer) 23 Sep 03 8:03 My problem with the md110 in combination with the dialogic D300 card is that with CAS (ICAT0006) signalling is missing.The dialogic card does not see incomming calls or is able to detect call pickups when making a call.What parameters am I missing here ?
2B+D ROUTE WITH CISCO 1751 ROUTERthread806-676368Share This Forum Search FAQs Links Jobs Whitepapers MVPs
Find A Job or Post a Job Opening Click Here.Runis (TechnicalUser) 9 Oct 03 12:40 Hi everyone,I have an MD110 BC10 system and I want to configure a 2B+D route between my system and a Cisco 1751 Router (ISDN-BRI). I have tried all kinds of ROCAI/RODAI variations, the channels are not blocked but it does not work.
Please, do you know what kind of route configuration do I need??
Thanks for your help!!!!!!!!
Astonces (TechnicalUser) 9 Oct 03 13:39 Hi Runis,
What do you want with this connection?
Do you want make a system between 2 MD110 with QSIG or one system between a MD110 and one CISCO?
I have something in BC9 for QSIG....
whosrdaddy (Vendor) 9 Oct 03 14:50 try this :
VARC=00000314VARO=15500000VARI=06010000 MD as USERVARI=06310000 MD as NETWORK
http://www.damovo.com
Runis (TechnicalUser) 10 Oct 03 3:48 Hi Astonces,
I want to make a Q-SIG between two MD (with 2 router), but the problem is that the connection between the MD and the router is E&M in one side and 2B+D on the other one...
Thanks,
TLU76/3thread806-678917Share This Forum Search FAQs Links Jobs Whitepapers MVPs
coslo (TechnicalUser) 13 Oct 03 11:15 I have a problem with the channels in an E1 CAS R2 link with PSTN. They are remaining one by one in NOPROGRESS / BUSY status until the communication is blocked. The channels are not connected ( I checked with LSCOP command ) but when I try to acces the route the message "Congestion" is appearing on the phone display. Only with command BLDBE the channels are released. The MD110 version is BC11, SP3. Thanks!
whosrdaddy (Vendor) 13 Oct 03 11:21 I think you'll need a serious upgrade to SP12(or even 13). there are several fixes regarding CAS... http://www.damovo.com
soaplover (Programmer) 13 Oct 03 11:28 Be sure to use appropiate VAR parameters and TL block also..
fcpli (TechnicalUser) 13 Oct 03 16:06 Are you using/having remote/mobile extension (REEXP)?
whosrdaddy (Vendor) 14 Oct 03 2:57 fcpli: RExxx commands are only available from SP9 http://www.damovo.com
fcpli (TechnicalUser) 14 Oct 03 5:18
Are you using/having remote/mobile extension (-----)?
coslo (TechnicalUser) 14 Oct 03 10:47 I don't have remote/mobile extension! I'm afraid the problem is around the TLU76/3 or TMU revision ( PROM-SET ). I upgraded the system from BC9 and before I didn't had that problem. The parameters for the route are the same.
whosrdaddy (Vendor) 14 Oct 03 11:09 coslo: aks your service provider for an update to SP12, changes are that your problem will be gone! http://www.damovo.com
CPKC (TechnicalUser) 14 Oct 03 14:13 I have this problem with SP12.
soaplover (Programmer) 15 Oct 03 0:24 Post your RODAP , ROCAP and RODDP for the dests .
There is often changes between releases that makes it neccesary to ajust some parameters .Specially the var parameters have to be compaired agains previous AS to get the same characteristics .
whosrdaddy (Vendor) 15 Oct 03 1:46 what do you mean CPKC? http://www.damovo.com
fcpli (TechnicalUser) 15 Oct 03 9:37 Are you using MFC? If yes, which is your R-state of MFU or MSU/MRU1&2?
CPKC (TechnicalUser) 15 Oct 03 15:31 To whorsdaddy
I also upgraded system from BC 9 to BC 11 SP12.There was no problem before.Since i change SIG parameter i have less channells in noprogress/busy state ,but they appeares sometime.
whosrdaddy (Vendor) 16 Oct 03 1:17 to coslo/CPKC : are you using paging (beepers)? http://www.damovo.com
coslo (TechnicalUser) 16 Oct 03 3:06
<ROCAP:ROU=10;ROUTE CATEGORY DATAROU SEL TRM SERV NODG DIST DISL TRAF SIG BCAP1 011000000000001 4 0001000001 0 30 128 00151515 011101000050 001100
END
<RODAP:ROU=10;ROUTE DATAROU TYPE VARC VARI VARO FILTER1 TL30 H'00000000 H'00000015 H'00000455 NO
cnbip:bpos=001-1-73;BPOS BOARD/BRDID PRODUCT NUMBER REVISION STATUS ADD /IND
001-1-73 MFU ROF1375348/1 R3B
END
I don't use paging (beepers).
soaplover (Programmer) 16 Oct 03 4:07 The var parameters compaired between bc9 & bc11 seems to match.The changes to BC11 VAR does not affect your spesific setting.Note !There are changes between the releases BC9/BC11.TL30:VARC D5 newD6 changedD7 equalD8 changedVARID5 newD6 changedD7 equalD8 changedVAROD4 newD5 changedD6 equalD7 equalD8 equal
However the programming looks like you are using MFC as register signalling SIG d11=5 , and digit reception/sending is DTMF the VAR parameters VARI d8 and VARO d8 your parameters are stated with tone code(dtmf) .Also i advice to change SIG d5=1 .in BC11 the SIG d5 is reserved to 1 (should not be 0 ).Other than that i looks okay.//Regards Soaplover
fcpli (TechnicalUser) 16 Oct 03 8:11 Your ROCAP and RODAP have a small mismatch: The B-answer from PSTN is ON in ROCAP but OFF in RODAP. I am not sure if it has anything to do with the prblem, but...
ROCAP:d4RODAP:VARO d7
rocap d5 has no affect (goes to nowhere)
If the problem is still there, try to make a call and trace TLP30.stisr;stuni:unit=tlp30,lim=x; (where the trunks are)sttsi:tri=1;make a callsttse:tri=1;strap:tri=1;and post it to the forum
NADAP; gives "COMMAND UNKNOWN" after initial load.thread806-637300Share This Forum Search FAQs Links Jobs Whitepapers MVPs
Check Out Our Whitepaper Library. Click Here.struthmate (TechnicalUser) 24 Aug 03 19:10 G'day All,I have created an INL file for my BC9 single lim PABX and thought everything was going fine. When I try and print number analysis or EXDDP:DIR=ALL; I get:-<NADAP;COMMAND UNKNOWN<I followed the directions in Alex under "Start of PABX" but got confused at point 60 in the flow chart which is "Enter the LIM disposition with the software configuration" I did the following:-<CNPUP;
LOADED PROGRAM UNITS IN EXCHANGE PU-NO PU-NAME PRODUCT NUMBER REV PATCH H' 3 EXS 7/CAA 111 442/1 R1A YES H' 4 PRP 6/CAA 111 583/2 R5A NO H' 5 PRH 7/CAA 111 441/2 R4A YESetc,etc,then got those program units and added them into the command:-<CNLDI:LIM=1,GSMULT=0-0,UNIT="PU-NAME";EXECUTEDthen:-<CNLDI:UNIT="PU-NAME";EXECUTEDthen they showed up in CNLDP;so done CNLDT;, LAPUT;, BLLTE;, SFEXI; and Dumped.
So can someone point out where I have gone wrong or what I have missed?Thanx,spence
mdfan (IS/IT--Management) 25 Aug 03 4:47 Writing a LIMdisp by hand ... sounds scary .. not recommendable at all.Have some send it you instead .
FICRI (TechnicalUser) 25 Aug 03 5:09
Hi,
When you make an initial load neccessary I/O programs are loaded automatically. To be able to continue from this point you have to specify all programs to be loaded to the system. This is done in the LIM-disp table.
It seems like your system only have the neccessary I/O programs so you have to start all over again from scratch. Make sure to have a complete LIM-disp table prepared in advance. You need a LIM-disp file for your specific BC release and Application System (Country).
patcher (TechnicalUser) 25 Aug 03 19:18 Your loading is not complete!!! Its okay if you are doing it for fun but if you are doing this for real; leave it to the experts. //patcher.
struthmate (TechnicalUser) 28 Aug 03 2:49 Ended up getting one from a bloke who has an Ericsson contact. Thanx for replies and the direction though. No doubt I will need to post again. ;)
MDadmin (TechnicalUser) 14 Oct 03 4:59 hi struthmateI hope your problem was solved.check if you have loaded NHH, if not try it:<LAPUL:UNIT=NHH,LIM=X,PATH=;after successful loadingSFCEI;
ACD Problem Parnum 138???thread806-665723Share This Forum Search FAQs Links Jobs Whitepapers MVPs
Kronehead (TechnicalUser) 26 Sep 03 19:30 I have just programmed up 5 ACD groups with overflow to a 6th group which should have music on wait and RVA's. The MD is BC9. I copied all the settings from another BC10 system with exactly the same set up. The BC9 won't pass the calls to the queue - it just keeps the initiated call open. The only difference I can see (apart from ROC 0230 for BC9 & 023001 for BC10 which doesn't look relevant)is PARNUM 138 False B answer duration is set to 5 on the working BC10 & 0 on the BC9 with the problem. Calls to the ACD group numbers ring through OK when logged on and go to voicemail when no groups logged on, as expected.Can anyone help?Thanks, Kronehead
Kringsaa (TechnicalUser) 29 Sep 03 3:57 Hi
I am not sure I understand your problem. Is it the overflow to 6th group? If this is the case. Overflow is controlled by the SEL parameter (d4 and d5) ex: SEL=11010
Regards Kringsaa
summerdike (Instructor) 24 Oct 03 18:01 Have the 5 acd groups all the same CDINI destination (The 6 th ACD group)?Or does acd gr. 1 divert to 2 . Two divert to 3 etc.??What do you mean with "it just keeps the initiated call open"?
NADAP;thread806-700083Share This Forum Search FAQs Links Jobs Whitepapers MVPs
Find A Job or Post a Job Opening Click Here.Joel007 (IS/IT--Management) 6 Nov 03 7:29 Hello could someone please help?
In the NADAP I have 98 & 97 but I'm unable to dial this number 98740****. What am I missing? The number is live I can dial it from my mobile. But from the PBX I get vacant number.
Joel
whosrdaddy (Vendor) 6 Nov 03 8:30 we need some more info here...
NADAP:NUMTYP=CD;RODDP:DEST=98; http://www.damovo.com
Joel007 (IS/IT--Management) 6 Nov 03 8:53 whorsrdaddy,RODDP:DEST=98; the switch is saying it's not assigned and for some reason I am unable to cut and paste the print out NADAP:NUMTYP=CD. But 98 & 97 are there. CAT on both entries is 5 4 3 2 1.
Joel
rfpui (TechnicalUser) 6 Nov 03 9:09 HiJoel
Are you using LCR?
Joel007 (IS/IT--Management) 6 Nov 03 9:13 Yes
whosrdaddy (Vendor) 6 Nov 03 9:39 give these printouts then :
NADAP:NUMTYP=LC;LCDDP:TAB=ENT;LCDDP:TAB=DNT1;LCDDP:TAB=DNT2;LCDDP:TAB=FDT;LCLDP:lIM=ALL; http://www.damovo.com
ISDN Extensionthread806-711159Share This Forum Search FAQs Links Jobs Whitepapers MVPs
Check Out Our Whitepaper Library. Click Here.jfleitas (MIS) 20 Nov 03 4:23 Hi all!
I´m trying to open a new ISDN line in an ELU 26 board. What would be the right command?
Thank you!
whosrdaddy (Vendor) 20 Nov 03 4:44 ITNUI:DIR=xxx,EQU=1-0-30-00,cat=1,ACCTYP=0;
(change cat and equ to correct values) http://www.damovo.com
Interconnect MD110 and Meridian1 using VoIPthread806-703685Share This Forum Search FAQs Links Jobs Whitepapers MVPs
ErikHemeleers (IS/IT--Management) 11 Nov 03 2:19 We want to interconnect an Ericsson MD110 and Nortel Meridian 1 using VoIP.
Any experience ? Regards,Erik
mdfan (IS/IT--Management) 11 Nov 03 5:03 What are the technical conditions on each side ?Both switches with latest SW ?
whosrdaddy (Vendor) 11 Nov 03 7:27 Do you mean IP trunking??if this is what you want ,you can do this from E/// side in BC12SP1 software version via ELU32. if Nortel supports H323 and H245 protocols, this should be no problem http://www.damovo.com
fidde (Programmer) 11 Nov 03 9:11 I recomend you to use two webswitches and tunnel a q-sig link over IP. This way you will get the features that exist on q-sig in between (Call back, Frowading, Path replacment....). H323 the Ericsson way do only support BC to other systems.Fredrik
ErikHemeleers (IS/IT--Management) 11 Nov 03 17:08 As requested by "duvel" : both switches will be upgraded to the latest version if necessary.
Nortel : Version 25MD110 : BC12
SYAR2003 (TechnicalUser) 11 Nov 03 17:25 Please dont confuse ErikHemelers with h.323 extensionsin this request .As fidde says , he needs some equipment tointerconnect the pbx's .The only tested solution for this is some kindof ip-router/ip-gateway with g.703/qsig supported interface .The services between Nortel and MD is to be looked at asa bonus , what we could get to work in GFP .The use two webswitches and tunnel a q-sig link over IPcan be one alternative .There is also Cisco and other like RAD that delivers usable equipments .
I recommend a following setup:MD ip-router ip-router Nortel/tt] |--| |--| |--| |--|| |<-qsig->| |<----lan/wan---->| |<-qsig->| ||--| |--| |--| |--|
SYAR
TLU76 - TLU79thread806-717421Share This Forum Search FAQs Links Jobs Whitepapers MVPs
Check Out Our Whitepaper Library. Click Here.vince62s (TechnicalUser) 28 Nov 03 5:38
What is the difference between TLU76 and TLU79 ?
there are a bunch of connectors on the TLU76 but only the bottom one is connected to a 30ISDN box
is the only difference the fact that TLU79 has only 4 channels?
thanks
RFLII (TechnicalUser) 28 Nov 03 5:47 The TLU76 is an board for an ISDN PRA connection. The TLU79 is for BRA conection
vince62s (TechnicalUser) 28 Nov 03 11:01 well I am not that technical....what is the difference?
thanks.
SYAR2003 (TechnicalUser) 28 Nov 03 11:39
TLU76/1 has 32 timeslotsPRI/PRA = ISDN Primary Rate interface/Primary Rate Access0 for syncronization16 for common signallingand channel 1-15 + 17-31 for carrying voice/dataEach channel is 64kbit witch means the board is a 2Mbit interface board .Giving it a total of 30 speech channels .(30 trunks + Sync channel + Signalling channel)
TLU79Has four time 2B+D channels (BRI / BRA)BRI/BRA = ISDN Basic Rate interface/Basic Rate AccessOne B channel is 64kbit and the signalling channel is 16kbit.Giving it a total of 8 speech channels .(8 trunks + 4 signalling channels one pr. BRI)
How is that for an explanation of differenceSYAR
vince62s (TechnicalUser) 28 Nov 03 12:07 thanks SYAR, thats' clear.
Now, can I connect an ISDN interface of a Cisco Router to one of these boards? both of them or just one kind ?
thanks
SYAR2003 (TechnicalUser) 28 Nov 03 12:33 TLU76
vince62s (TechnicalUser) 29 Nov 03 4:38 additional questions:
on the TLU 76 there are potentially 8 connectors.
are all the 30 voice channels connected to the bottom one ? (thats's the one connected to my T2 box)
what are the others for?
if I have to connect my other TLU76 to a cisco router, will it transport all the 30 voice channels?
thanks
SYAR2003 (TechnicalUser) 29 Nov 03 6:01 Connections to use is on the lower half of the board
A B C
x x xx x xx x xx x x
x x xx x x
x x xx x x
x x xx x xx x xx x x
x x xx x xx x xx x x
_____| || || |_____
x x x 02x x x 04x x x 06x x x 08
x x x 10x x x 12x x x 14x x x 16
x x x 18x x x 20x x x 22x x x 24
x x X 26x x X 28x x Y 30x x Y 32
TLU76, 120 ohm twisted pair cableconnects to the fourth connector seton the lower half.bold marked X is is the boards tx pairbold marked Y is is the boards rx pair
Connections is on the lower half of the board
A B C
x x xx x xx x xx x x
x x xx x xx x xx x x
x x xx x xx x xx x x
x x xx x xx x xx x x
_____| || || |_____
x x x 02x x x 04x x x 06x x x 08
x x x 10x x x 12x x x 14x x x 16
. . . 17X X X 18 X Y X 19X X X 20. . . 21X X X 22X Z X 23X X X 24
x x x 26x x x 28x x x 30x x x 32
TLU76, 75 ohm coaks cableconnects to the third connector seton the lower half.bold marked Y is is the boards tx pinbold marked Z is is the boards rx pinbold marked X is is the boards coaks shield(GND)
vince62s (TechnicalUser) 29 Nov 03 6:53
Thanks SYAR!
if I understand well:
1st part of your answer: TLU76 to T2 box2nd part of your answer: TLU76 to Cisco Router
now, it means I can use a single TLU76 for both connections, right?
how will the split between the 30 channels be handled?
SYAR2003 (TechnicalUser) 29 Nov 03 7:00 I'm not sure if you get it .It depends if the external equipment is deliveringa 75ohms coaks interface or a RJ45 120ohm pair connection.
I don't know what you mean by a t2box but if it has a coaksinterface yes it connects to a tlu76 at the third connector.And if it has a rj45 120ohm pair connector it connectsto the tlu76 at the fourh connector.
cisco routers delivers 120ohm pair via rj45 connector.
vince62s (TechnicalUser) 29 Nov 03 7:11 ok I see. clearer.
it means I have to use the second TLU 76
just for info, the T2 box is the telco trunk with 30 ISDN channels.
but I still cant see how I can use the second TLU76 for internet access over ISDN through the cisco router.
is all of this just for voice?maybe I should invite you in Paris!
SYAR2003 (TechnicalUser) 29 Nov 03 7:23 Explain to me what you are trying to achieve here.
I'm stumped.
vince62s (TechnicalUser) 30 Nov 03 8:29 I am trying or planning 2 different things:
1) internet access through ISDN for backup purpose. I dont want to order a new ISDN line since I already have these 30 channels. My idea is to connect the cisco router to a ISDN interface of the MD 110 , then I could have internet access.
2) My other plan is to have a remote site connected to the internet and have voice over IP with the TLU76 connection to the cisco router.
clearer?
mdfan (IS/IT--Management) 30 Nov 03 12:26 Vince , I think we are mixing telecom and datacom here.1) The ISDN of the MD110 is connected to PSTN and not a ISP . How can you access Internet through this ISDN then ? It must be through a dial-up connection then towards an ISP from a S0 equipment in the MD110. Or ?
2) This is possible , what kind of equipment do you plan to deploy at the remote site ? WEBSWITCH2000 ?
vince62s (TechnicalUser) 1 Dec 03 3:33
1) I see your point. However, what is a S0 equipment? I just have ELU28 and ELU29 cards plus a TLU79. I was trying to use existing equipment, but maybe I cannot accomplish dial-up over ISDN with these.
2)ideally I would like to do the same thing at the other end but I need to find out the PBX model first.
thanks
mdfan (IS/IT--Management) 1 Dec 03 7:47 Dial-up over ISDN from the MD110 , pls use either S0 adapter / Dual Access product which actually uses uses the ELU28/3 card configured with 32 individuals instead of 16.Or use ELU26 which gives you 4 BRA interfaces from within the MD110.
From any one of these products , just dial 0 + the ISP access number.
ozgur74 (TechnicalUser) 1 Dec 03 8:50 AND TLU64 ?Is it same ?what is TLU64 , differances ?
SYAR2003 (TechnicalUser) 1 Dec 03 9:00 Duvel ! whats the difference of havinga So/BRI connected to the router and a PRI from the MD.Access to internet would be possible anyway.
vince62s (TechnicalUser) 1 Dec 03 9:22 ok SYAR, so what's the step-by-step PRI/MD solution?
SYAR2003 (TechnicalUser) 1 Dec 03 10:17 Simple scematics
. . . . . . . . . LAN . . . SITE A . -------- . . |router| . ---^---- . ^ . | . | . . | . | | |-------| | | | MD | | | | | | | |--| |--|
| (2)T|L U 76| | | T|L U 76 pstn(1) | |<------- | | ----------> WAN | | | | | |--|-|--| | | | | - - | - - - - - - - - - - - - - - - - | | | . . . . |. . V . . LAN . . . SITE B . -------- . . |router| . . ---^---- . . | . . . | . | |-------| | | MD | | | | | |--| |--| (4)T|L U 76| | | T|L U 76 pstn(3) |<------- | | ----------> | | | | |--|-|--|
mdfan (IS/IT--Management) 1 Dec 03 10:53 Sure if IP trunking is just what he wants ....
BUT
corporate WAN = Internet ??
What do you mean with Internet ?
SYAR2003 (TechnicalUser) 1 Dec 03 10:58 Your routers will now have the possibility todial-up to your ISP's servicenumber ifyou pass the accesscode for PSTN+ISPnumber tothe tlu76 connected to your router.The internet ISP call will then go trough the md switchand out on the TLU76 connected to PSTN.
The same time you will have qsig connectionfor internall calls over ip between site A & B .
vince62s (TechnicalUser) 1 Dec 03 13:02 this sounds great.
now how do I configure the TLU76 (2) for:
1) initiate dial up on TLU (1)2) route the information properly.
mdfan (IS/IT--Management) 2 Dec 03 4:55 Wouldn't this imply the PBX act as a ip-router ?Indeed if possible , a very nice setup ; so SYAR2003 plstell us how ? (we will pay you well )
SYAR2003 (TechnicalUser) 2 Dec 03 5:28 It's just to setup the RODAI ROCAI RODDIas QSIG networking with closed numbering plan.The MD data should be setup to support GFP (Generic Functional Protocol) and to tunnel UUS data through GFP.The cisco ip-routers must be enabled to support QSIG w/GFP from the g.703 interfaces .
Something in the MD like (for BC11)VARC=00000310,VARI=75440000,(1-30 channel numbering)VARO=06300000 or 06400000 ( network or user)SIG=111110000031ADC=150510000000025010500000SERV=0110000001SEL=X11000000000001
Rest is in the routers witch is not my field i'm afraid.
Match the VARO's user side/network side to correspont with the routers to get the d-channel established.
SYAR
mdfan (IS/IT--Management) 2 Dec 03 5:36 Isn't this what is needed between (2) and (4) ?
Are you saying that this automatically gives the ISDN internet backup between (2) and (1) ? This is what vince wants.
SYAR2003 (TechnicalUser) 2 Dec 03 5:53 That is configured in the ip network /routers.Im not saying anything gets automaticly done.
It must be configured to work .How thats done in the routers i cant answer.If 0 is the access code for pstn at (1)the router in sita a has to dialup to (2) 0 + isp number and logon to the ISP.
Other internet routers must be updated by this routeso thay can have it as a backup route to internet.
This setup makes all that possible if someone thathas the right expertise can configure it correct.And the two md's is also qsig networked over ip.
"Dont hijack the tread"
mdfan (IS/IT--Management) 2 Dec 03 5:59 Have you done this router configuration ?
SYAR2003 (TechnicalUser) 2 Dec 03 6:07 This is excatly the same: . . . . . . . . . LAN . . . . -------- . pstn(1) . |router|<-----------------ISDN PRI -------- . . . . . . . .
SYAR2003 (TechnicalUser) 2 Dec 03 6:25 "vince62s (TechnicalUser) Nov 30, 2003 I am trying or planning 2 different things:
1) internet access through ISDN for backup purpose. I dont want to order a new ISDN line since I already have these 30 channels. My idea is to connect the cisco router to a ISDN interface of the MD 110 , then I could have internet access.
2) My other plan is to have a remote site connected to the internet and have voice over IP with the TLU76 connection to the cisco router.
Isn't this what we have covered here .
fidde (Programmer) 2 Dec 03 7:45 SYAR is correct this is no problem in achiving this. Though you will need special cisco hadware and a good cisco technican. We have been running both this senarios and number 1 is a easy thing, number 2 deamands special IOS software in the router for IP telephony.
Fredrik
SYAR2003 (TechnicalUser) 2 Dec 03 8:57 Thanks Fredrik.There is also a Cisco router forum hereForum557
vince62s (TechnicalUser) 3 Dec 03 2:34 SYAR,
will the config you mentionned VARI,VARO,... work with BC10?
also I have a E1/PRI cable with one end 13 PIN connectors going into the ctrl of the router, on the other end a RJ45. SHould I assume the RJ45 is a regular double pair tx rx?
what will be the actual speed between the MD and the router?
SYAR2003 (TechnicalUser) 3 Dec 03 3:14 I have to look at the parameters again.What BC10 cna version is it.
The connection to TLU76/1 is regular pair yes.The board should come with a connectioncable for pair named TSR 901 0481.If you don't have it ,order it from your local MD110provider .
Actual speed , i don't understand .This would be the same as having a ISDN from PSTNconnected to your router. It depends on how it's setupto dial the ISP (number of b-channels to establish)One b-channel is 64kbit.It's upto you and a cisco technican to decide .Just don't take so many channels that if effects thepbx voice traffic .
And do as Fredrik says consult a cisco technican withexperience of setting up voip on cisco equipment.
There might be some licenses in the MD you must purchase also if they arn't in the system already.EXTERNAL-LINE-QSIG FAL104466 30 pcs. for one tlu76NET-SERVICES FAL104505 1 pcs. for one MD
How change analog extension to ipthread806-732986Share This Forum Search FAQs Links Jobs Whitepapers MVPs
marcosa (IS/IT--Management) 18 Dec 03 9:17 Hi folks! I need know how change analog extension to ip on BC8 packet Q. I have installed call manager
connected to MD110 through TLU76. Greetings.
SYAR2003 (TechnicalUser) 18 Dec 03 15:04 explain some more please ....
The analoqe number sits in the md .The connection to callmanager is a trunk .You can't exchange this analoqe internal number in the md to ip in the callmanager .
What you can do is to direct incoming calls to this number over the trunk to callmanager and a H.323 extension there .
But theese extensions are completly isolated from eachother.
Note!You really dont need cisco callmanager if you have a md110.Update it to BC11 or BC12 and its fully IP extension enabled (and bc12 network md's directly via md's ELU32 card),and you have full feature transparency betweenip-extensions ,cordless extensions , analoqe extensions ,digital extensions ,mobile extensions and operator.
Hope i got the scenario right.RegardsSYAR
njohn343 (TechnicalUser) 19 Dec 03 20:33 A comment & a question :
Comment : The importance of feature transparency mentioned by SYAR should not be underestimated. We currently have a Cisco Call Manager connected to our Ericsson BC10 with a QSig tieline. But there is no co-operation between the two oregarding common, useful features such as Group Call Pickup, Group Hunt, Callback, Supervision (monitoring of another extension), simple Diversion, .... Also, you end up having to administer two different systems and have the added burden of trying to get some sort of integration and basic cooperation between the two.
Question : It seems that there is no provision on an IP extension to Supervise (monitor) other Ericsson extensions, such as can be done on the DBC3213 digital using MDN and MNS. If this is so, how does one implement this feature at a BC12 site. Do you need to retain the traditional LIM in order to run ELU28 cards for digitals or is there some sort of 19" rack mount device such as the Ericsson Enterprise Branch Gateway (EEBG) which can accept ELU28s and retain full funtionality ? The EEBG can accept TLU and ELU21 cards, although I believe the analogue cards cannot be used for faxing. You need a DRG for that, I am told. Can an EEBG also accept an ELU28 to run a DBC213 or newer model digital ?
The sort of application I have in mind is the small branch office with say 20 - 100 extensions, mostly IP
handsets, but also requiring a receptionist position with the ability to monitor other extensions and handle lots of calls - traditionally the job of a DBC213. Can this be done in BC12 without the old style magazines ?
There remains a need for supporting legacy analogue equipment. There is all sorts of 3rd party equipment on the market designed for analogue lines which I think will be around for quite a while yet.
regards, John
whosrdaddy (Vendor) 22 Dec 03 5:26 EEBG is nothing more than a stupid webswitch 2000. this means NO analog extensions by default, you need like you said an analog card which is specific for webswitch (is no MD110 hardware) so forget about putting digital extensions on the EEBG. your need for support to have traditional hardware will be adressed in future version of the MD110 where the switching part will be overtaken by a standard unix server (MECS). http://www.damovo.com
marcosa (IS/IT--Management) 29 Dec 03 4:48 Hi Folks! Well, i has been had this. The first, a ´extee:dir=1111;´. Then, ´roddi:dest=1111,adc=06061000000000250,rou=11;´. Now, i need change extension as route, how can i do it?.
Thanks, happy christmas :)
SYAR2003 (TechnicalUser) 29 Dec 03 4:59 An easier way would be toEXTEE:DIR=1111;NANSE:NUMTYP=EX,NUMSE=1111;Initiate 1111 as common abbrivated number:NANSI:NUMTYP=AC,NUMSE=1111;initiate the common abbrivated number with access code(xx) for the ip-trunk + the H.323.number(yyyy)ADCOI:ABB=1111,CLASS=0&3,TRA=XXYYYY;
syar
marcosa (IS/IT--Management) 29 Dec 03 5:26 Merry Christmas Good. And now, how do i know access code for the ip-trunk?
Happy new year, yeah!
marcosa (IS/IT--Management) 29 Dec 03 6:00 Good Morning I has just done i want it. Instead nansi:numtyp=ac,numse=1111, it is numtyp=ed. The command ´adcoi´ isn´t neccesary. But, how can i open the number´s rage 22xx as ´ed´?
Greetings
SYAR2003 (TechnicalUser) 29 Dec 03 6:33 You pick out one number from the EX range .And put it in the ED range series.e.g
NANSE:NUMTYP=EX,NUMSE=2212;(not neccesary if not used)NANSI:NUMTYP=ED,NUMSE=2212;Or if 22xx is unused use only 22 as numse and roddi.That will give 2200-2299 , 100 numbers if 4.digits.
Then make the destinationRODDI:DEST=2212,ROU=X,SRT=1,ADC=..;
Does this make sense for you...
syar
marcosa (IS/IT--Management) 29 Dec 03 6:46 Hello Yes, it is correct. I has been finished the same. Thanks very much for all...at moment! XD
SYAR2003 (TechnicalUser) 29 Dec 03 8:54 Sure thing .
Intrusion into routethread806-752968Share This Forum Search FAQs Links Jobs Whitepapers MVPs
Check Out Our Whitepaper Library. Click Here.149149149 (TechnicalUser) 19 Jan 04 5:10 Is possible intrusion into route?I have DTS:EXTENSION DIRECTORY CATEGORIESCAT TRAF SERV CDIV ROC TRM ADC CUST LANG13 01131301 02151201 000140000 000001 2 00100001010 5
and route:ROU SEL TRM SERV NODG DIST DISL TRAF SIG BCAP10 011000000000001 4 2110000000 30 128 01151514 111110000031 111100
and i called *0*201#10 (into busy trunk), i pressing 4, DTS write INT REQUEST FAILED
jazaya (Instructor) 20 Jan 04 6:00 Your settings are correct and I can think of 2 things:1-The extension which is connected to the external line is not open to intrusion2-I donot know which BC version u r using but there exists a PARNUM value that restricts/allows intrusion on external line for BC11 it is Parnum=36 parval=1(allows int on extline).3-you should also check Parnum=26 for intrusion on incoming trunk.Good luck and keep us posted Experience it, there is no [email protected]
149149149 (TechnicalUser) 21 Jan 04 5:28
I have BC10(VERSION=LZY2035160/6/BC10CNA142/R4A) and PARNUM 26 and 36 is 1.
149149149 (TechnicalUser) 21 Jan 04 5:32 The extension which is connected have SERV D3D4=02
PDFMAN (TechnicalUser) 22 Jan 04 1:47
1-Is "The extension which is connected have SERV D3D4=02"the one connected to the ext line or is it for the intruding party?
2-Check parnum 68 as well if you are using a DTS for intrusion.
149149149 (TechnicalUser) 22 Jan 04 3:31 the one connected to the ext line have SERV D3D4=02, intruding party have 15PARNUM 68=1
md110user (TechnicalUser) 22 Jan 04 13:50 My friend from OPII you can intrude the call by the following example:dial the line e,g.:*0*101#9 I asume that rou=1,tru=1-1,dest=9
then you will find it is busy, now dial the ring puttom and you will hear the the caller talking. I hope that will be usefull.
Bye the way: you have to disable the ability from the operator to cut the line by checking parnum=68.
SYAR2003 (TechnicalUser) 22 Jan 04 14:08
149149149 !
Description of parnum 68 for BC10 cna143:
0= Dts is permitted to intrude on an external line1= Dts is NOT permitted to intrude on an external line.
So try having parnum 68=0 and use a Dts (not analog or anyother type of extension)
syar
To create category to restrict call to operator.thread806-778443Share This Forum Search FAQs Links Jobs Whitepapers MVPs
Tek-Tips Forums is Member Supported. Click Here to donate.dnaserver (TechnicalUser) 17 Feb 04 21:10 Hi MD110ism
I'm planning to activate 10 extensions for the use of 'intercom' in a campus. The purpose is to enable student to consult their lecturers from hostel. The criteria of the 'intercom' are as follows:
1) The 'intercoms' are restricted to call between each
others, this is to avoid misued by students to chat with each others.
2) The 'intercomes' are restricted to call/dial operators '0' extension, this is to avoid high traffic calling handled by operator.
3) The 'intercomes' are restricted call external no.
4) The 'intercomes' are only allowed to call normal extension no. (Lecturers no). Students are given hardcopy directory for thier reference.
Can anybody help me how to program step by step to create the best category for the above lines with the specified criteria?.
May God Bless You All
wfhy (TechnicalUser) 17 Feb 04 22:29 Hi,It is very easy.
step1: EXCCP:CAT=ALL; check created CAT.step2: EXCCS:CAT=X,SERV=,TRAF=D1D2D3D4D5D6D7D8,CDIV=; creat a new CAT,note D3D4/D5D6 must be a new value. SERV and CDIV parameter can be copy. step3: NACDS:NUM=lectures no,CDCAT=d3d4 of TRAF in step2.
SPEXI with NDCthread806-788881Share This Forum Search FAQs Links Jobs Whitepapers MVPs
Check Out Our Whitepaper Library. Click Here.serg75 (TechnicalUser) 2 Mar 04 1:21 Hi!I have a problem with non-dialled connection extension function. When I make execution of command SPEXI:DIR=1000,OPT=N,NDC=9; and I lift a handset from ext. 1000, the system ejects an error "VACANT NUMBER". I have some prefixs, which one start with digit 9 (i.e. 90, 91, 92... 97, 99), and also 98 is LCR. If in quality NDC put in example 90 (i.e. 9x), all will work correctly. But it is necessary to use NDC=9. Also it is possible to make false DEST (001 for example) and to make NDC=001 is will work, but then for 001 it will be necessary to adjust whole NADAP.Why all this takes place and how it is possible to decide this problem?I use following parameters:
ROUTE DATAROU TYPE VARC VARI VARO FILTER 99 SL60 H'00000210 H'11400000 H'06410020 NO
ROUTE CATEGORY DATAROU SEL TRM SERV NODG DIST DISL TRAF SIG BCAP99 011000990000001 5 1001000001 0 30 128 01070701 111110000030 111111
EXTERNAL DESTINATION ROUTE DATADEST DRN ROU CHO CUST ADC TRC SRT NUMACK PRE90 99 1006000000000250000 0 2 0
EXTERNAL DESTINATION ROUTE DATADEST DRN ROU CHO CUST ADC TRC SRT NUMACK PRE91 99 1006000000000250000 0 2 0
..........
EXTERNAL DESTINATION CODE 90 - 97, 99
LEAST COST ROUTING ACCESS CODE NUMBER SERIES 98
.........
KEY SYSTEM CATEGORY PRINTDIR TRAF SERV CDIV ROC ITYPE TRM ADC LANG1000 01151515 02151207 011151000 000001 21 0 00100000010 F
System is BC10 CNA141.
GioBs (TechnicalUser) 2 Mar 04 3:49 Which is your goal? what do you want that happen when off-hook the telephone?
serg75 (TechnicalUser) 2 Mar 04 4:58 Would be fine to hear dial tone from PSTN (or from MD110). But because D1=1 in ADC, that means "silence" as response, and that's no so good... But why "vacant number"?
gedii (Programmer) 2 Mar 04 12:54 Hi Serg75
The reason I feel that this is resulting in "Vacant Number" is due to the fact that the MD110 deems the request for simply a '9' as kind of incomplete and ambiguous in your switch. This is because, as you said, the actual 'ED' or 'LCR' codes defined in NADAP are expanded to the 9x format.
What I'm suggesting is that if for instance the entire digit '9' was defined as either an 'ED' or 'LCR' in NADAP, you'd probably find that your scenario would work.
I don't know if there are any Parameters or Patches that could help in overcoming this problem unfortunately.
Best Regards
gedii
DUFQI (TechnicalUser) 2 Mar 04 12:55 "NDC" has to be part of "NADAP" (EX,DE,...)Your problem is the LC Routing Access. Without this, you could have "9" as "ED" and different RODDI's starting with "9".
serg75 (TechnicalUser) 3 Mar 04 6:14 O.K. guysI can make so that MD generated the own dial-tone after the fixed least cost routing access code (LAC) will be dialled?
whosrdaddy (Vendor) 3 Mar 04 14:51 check aspap 104 for that http://www.damovo.com
serg75 (TechnicalUser) 4 Mar 04 0:10 Aspap 104 force generate dial-tone for all LACs. But may I make it for FIXED LAC?
Device Boards go PASSIVE - URGENTthread806-796498Share This Forum Search FAQs Links Jobs Whitepapers MVPs
Tek-Tips Forums is Member Supported. Click Here to donate.73vette (TechnicalUser) 10 Mar 04 19:59 Hi to all,
We have a strange problem.
We had a PU4DC power supply fail in a BC8.0 system with Consono LIMS.
Since we replaced the power supply, all of the device boards in the magazine have gone passive and we cannot get them to go ACTIVE.
Any help or suggestions would be appreciatted.
Thanks!
SYAR2003 (TechnicalUser) 10 Mar 04 20:57 Run the command SFCEI .It updates active magazines .
Also check with first LSCNP:LIM= ;that the dsu is operational .
Syar
megglesfield (TechnicalUser) 10 Mar 04 20:59 Try SFCEI
73vette (TechnicalUser) 11 Mar 04 12:25 Thanks,
SFCEI fixed it!
problem with tlu76/3thread806-792914Share This Forum Search FAQs Links Jobs Whitepapers MVPs
Check Out Our Whitepaper Library. Click Here.jonhf (TechnicalUser) 5 Mar 04 22:50 Hi
I have a problem with the conection between a ericsson bc 9 (TLU76/3) and panasonic td 500 (E1). I have sychoronize and connection but when I take a channel and dial any number dosen´t happen
The Rocap
sel 71200000 serv, 211000000, sig 3111000005,trm=5
Rodap
varc 00000008, vari 00000006, varo 00000455
CAS, MFC, DR2
thanks
rfpui (TechnicalUser) 6 Mar 04 6:19
himore info where is the problem?You can't connect from MD to Panasonic or from Panasonic to MD?
and send RODDP:dest=(to panasonic)
SYAR2003 (TechnicalUser) 6 Mar 04 7:35
Jonhf !The settings in the panasonic is important to .E.g what one side excepts from the other likepts ,seizure , tone , mfc signalling type , etc .
We often have to break down the var parameters andcross check features/values with other side in theese kind of trunks.
Or perhaps you rfpui is an expert on panasonic also ,so you can circle your magic wand and propose a solution
for both sides .
Syar
jonhf (TechnicalUser) 8 Mar 04 11:18 Thanks RFPUI, and SYAR2003 for being so helpful.
The problems we thank is the same in both equipments MD and TD500.
The information requested is as follows:MD110Dest: 7810, Trc: 0, Srt: 0, NumAck: 0, Adc: 0005000000000250.
In the TD500:Trunk DR2, with MFC signalling.
The problem as we perceived is that when we try to get the trunk on any side we can hear the dial tone but when we dial any number we only receive white noise.
rfpui (TechnicalUser) 8 Mar 04 12:08 Are you sure that you don’t have alarm 303 Data link alarm in AL log?
jonhf (TechnicalUser) 8 Mar 04 12:19 For RFPUI
Yes, I don´t have any alarm
SYAR2003 (TechnicalUser) 8 Mar 04 13:05 Is that TLP30 u're using .Btw the dest i suppose the srt=1 not zero .
SYAR2003 (TechnicalUser) 8 Mar 04 13:21 From what i see you have
MFC Code type to Ericson code.(VARC D8=8)perhaps use standard type CCITT code - D8=0
Incoming digits MFC (not tone/DTMF)
Outgoing digits Tone/DTMF .
Are you sure this is the right setting.Only purpose i would have incoming to MFC is to show a-number .But then it would have to be requested i think .
rfpui (TechnicalUser) 8 Mar 04 13:24 hi Why D8=8 in VARC?From alex D8 is MFC type signaling
from 0 to 7 is CCITT CodeAnd from 8 to F Ericsson –code
In my opinion D8 should be set to 0
fcpli (TechnicalUser) 8 Mar 04 13:31 Seems to be that you don't have MSU/MRU/MFU boards inserted (for MFC).
SYAR2003 (TechnicalUser) 8 Mar 04 13:35 Well he could set DTMF in both directions ,
and have the line code to CCITT standard .
What do you think RestartUnit ...
jonhf (TechnicalUser) 8 Mar 04 13:54 Hi
Yes I Have MFU inserted and change de VARC (D8=0) in other test but dosen´t happen,
I don´t know it is possible to change for E&M
rfpui (TechnicalUser) 8 Mar 04 15:48 Hi jonhfHave you any documentation to MD program TLP30? Such as Alex or Dynatext?Because you must try more combination of VARI & VARO.Now I find another fault or mistake VARO D8=5 it is tone digits transmission to interworking exchange If you send printout from MD use copy and paste function. It is better For example your SIG is only 10 digits and should by 12
jonhf (TechnicalUser) 9 Mar 04 11:08 Thanks RFPUI, and SYAR2003 for being so helpful.
Up today the problem is solved and the fault was in the Panasonic, the problem was in the MFC signalling in the Panasonic side.
PS
I don´t have the Alex or Dynatext softwares, there is any possibility that you can bring me that information, or please tell me were I can get it. I live in Mexico. Best Regards. John F.
what "exactly" does an sfcei dothread806-792064Share This Forum Search FAQs Links Jobs Whitepapers MVPs
Tek-Tips Forums is Member Supported. Click Here to donate.lancbomb (TechnicalUser) 5 Mar 04 3:43 regarding program units etc.
cheers
mdfan (IS/IT--Management) 6 Mar 04 3:31 it enables intercommunication of signals between units but it does not open the PBX for traffic.
SYAR2003 (TechnicalUser) 6 Mar 04 4:40
As for lancboms's question what exactly does an sfcei do.That's not quite easy to describe without writing 100 pages ,as there is a lot happening on signallinglevel in the switch .
But here is a short description ,hope this helps .
Command SFCEI executes phase 1.3 and phase 1.5 in the entire system. This command [i]does not affect the traffic in the exchange[/i]. It is mainly used after the system has been reconfigurated.
Before phase 1.3 is executed, system tables BLT, PDT and the changed CFT are distributed ,update of BLT,PDT,CFT is important eg. if new programs is added/removed ,lim added/removed etc.
BLT Broadcast Link Table
The function of BLT (Broadcast Link Table) is to permit broadcast signalling in the system. Broadcast signalling means trying to reach a certain program unit in all LIM:s in the entire system by means of one signal.
BST and, consequently, BLT are built up of information which ECM has acquired continuously. Faulty LIM:s are always placed at the last position in BST.
This subfunction is initiated by signal BLTDISTR to ECM. ECM then distributes BLT data, on the basis of BST, to all LIM:s. LIM:s which do not answer on the signal during the BLT distribution are regarded as faulty, and are therefore marked as faulty.
Updating is done whenever a LIM has been marked as faulty and on a request from RE during the start.
A faulty BLT is detected through ECR checking that routine test signal EXTLIMTEST is sent from the correct FATHERLIM according to BLT. ECR also checks if own ROOTLIM number is equal to FATHERS ROOTLIM number. The result is included in reply signal EXTLIMTESTRT. If the SON considers himself to have a faulty BLT, he sends signal FAULTYBLT to ECM and informs the FATHERLIM who sent this EXTLIMTEST that there is a fault in BLT. This is done because the FATHERLIM might also have a faulty BLT. This FATHERLIM will then send FAULTYBLT too, and both LIM:s will get a new BLT. If ECM receives more than two FAULTYBLT at a time he will perform a total BLT distribution with signal BLTDISTR. A total distribution is also performed if a LIM reports a faulty ROOTLIM number in signal FAULTYBLT.
PDT Processor Distribution Table
The processor distribution table contains data needed for communication to/from other LIM-processors. All LIMs in a system have a position in PDT. The own LIM position is used for the communication with other processor side within a LIM. A PDT position contains the following data: Signalling path to LIM processor. The path consists of a multiple number to the board handling external signalling, an address to receiving LIM and signal split size. Sequence numbers for sending/receiving inter-processor/inter-LIM signals. Collect pointer. Points to the signal buffer where the subsignals are collected in. Collect subsignal pointer. Points to the position in the signal buffer where received subsignal is to be stored.
CFT Common Function Table
The function of CFT is to simplify signalling to CF programs. CF programs are programs that are located
only in one LIM. For security reasons, these programs may be duplicated in another LIM.
Utilizing this system table means that not all programs, which signal to the CF program, need to know which LIM they are loaded in. CFT provides the system with this information.
CFT is built up on order from RE, signal UPDATCFINFO. ECR in all LIM:s is then ordered to collect data about the programs that is CF and in which LIM:s these are loaded. ECM then collects the same data. The data is collected from PIR. UPDATCFINFO is only sent before phase 1.3.
Before phase 1.3 or phase 1.5 (depends on if phase 1.3 is executed or not) RE orders ECM to distribute CFT data to ECR. This is done with signal CFTDISTR. ECM's view of the CFT is distributed (TRAWCFT). If CF with lowest or highest LIM number is active and status on active and passive CF. ECR now updates it's CFT according to ECM's.
At initial load the common function with the lowest LIM number is set active.
Updating takes place when a change between active/passive CF is made, routinely and on a request from RE during the start.
Phases in sfcei 1.3 & 1.5
Phase 1.3 The phase 1.3 does not make any difference between the initial start and the restart cases.
Phase 1.3 is only executed in an initial start and when the system has been reconfigured.
During phase 1.3 an information exchange between different PU's can take place by means of regular signals.
The broadcast signalling structure has been organized just before phase 1.3, which implies that broadcast signalling reaches all initially started LIM:s.
Before phase 1.3 the CFT, BLT and PDT are distributed.
Examples of the information which is treated in some PU's during phase 1.3 are:
which LIM:s exist in the system which common functions exist and where are an active and a passive (if any) version of such a program located.
Phase 1.5 In phase 1.5 you do not make any difference between the initial start and the restart cases.
During phase 1.5 an information exchange between different PU's can take place by means of regular signals.
The CF-table is distributed in these cases when phase 1.5 is not preceded by phase 1.3.
Syar
lancbomb (TechnicalUser) 8 Mar 04 3:53
thanks Syar !
CAT not checked if SPEXIthread806-802110Share This Forum Search FAQs Links Jobs Whitepapers MVPs
serg75 (TechnicalUser) 18 Mar 04 0:03 Hi!
DIR A has CAT=Z. He (she) may dial X-X, but may not dial X-Y (according to own category). And that is correct.
But if I make SPEXI:DIR=A,OPT=N,NDC=X; then he (she) may lift a handset and dial Y. Why it is happening? And what I must do to prevent this?
SYAR2003 (TechnicalUser) 18 Mar 04 1:09 First way to prevent this may be to have the latest CNA orservicepack .Theese kind of faults may be corrected by patch(es).
Please inform system status BC version and cna/sp level.
serg75 (TechnicalUser) 18 Mar 04 1:15 Syar,system is BC10 CNA141 :(
rfpui (TechnicalUser) 18 Mar 04 15:36 Hi allSYAR: in main opinion you are an super expert
But I thing that is no fault and no correction exist (maybe for special market)OPT=N means that is non-dialed connection and in consequence NDC number is not analyzed by Category restriction. D3D4 & D5D6 position in TRAF (Extension category) are ignored.But TRAF position D7D8 traffic connection matrix is analyzed .
I’m sorry for my English
SYAR2003 (TechnicalUser) 18 Mar 04 16:33 Very well i'm sure you are right rfpui.As i think about it this must be constructed that wayfrom the start as the normal intension to use spexi is with a complete b-number thats entered by an md administrator.That way the spexi is controlled by the customer himself.The designers of the function may not felt that it was neccesary to add code for tcd analyzis for this reason.
I can only think this is the reason for that behavior .
Later it has been popular to make an NDC to 0(access code)for faxes and such .So it ends up to be the md technicans responsibility to inform the customer about the negative side ofthis usage.
Syar
rfpui (TechnicalUser) 18 Mar 04 17:01 SYARThanks for your opinion Other words can we write an answer to serg75 that is not fault ?
SYAR2003 (TechnicalUser) 18 Mar 04 17:26 Only way to be sure is to do a trace ifit attempts tcd analyzis or not (CHENUM to NAP )
But i think our conclusion is right .
Syar
serg75 (TechnicalUser) 18 Mar 04 22:36 Hi guys.Thank you for yours research!
I must emulate PSTN port in ELU29, but that port should be not accessed to international service. By means of what that may be reached?
SYAR2003 (TechnicalUser) 19 Mar 04 7:05 Serg !The answer is that you cannot control cdcat datawhen spexi is set to access code .It will be open forall numbers as no numberanalyzis is done .(this is that negative side i mentioned)
Syar
Alternate routing not working.thread806-800141Share This Forum Search FAQs Links Jobs Whitepapers MVPs
lancbomb (TechnicalUser) 16 Mar 04 4:54 Hi,
Have a prob with alternate routing,
LIM1 = 01895 areaLIM2 = 01865 area
ROU1 = DASS (01895)ROU4 = DASS (01865)ROU2 = ANA (01895)
Routes so that LIM1, = rou1, rou4, rou2 LIM2, = rou4, rou1, rou2
If LIM1's DASS goes down, second and third rou, apparently worksIf LIM2's DASS does down, 2nd and 3rd choice, def dont work.
LIM1 is main site so is generally bomb proof.
below is print out (BC10) any ideas, cheers-------------------------------------------
<NADAP;NUMBER ANALYSIS DATA TYPE OF SERIES NUMBER SERIES EXTERNAL DESTINATION CODE 77 781 - 786 79LCR ACCESS CODE NUMBER SERIES 9EXTERNAL NUMBER LENGTH DATA EXTERNAL NUMBER NUMBER LENGTH71 2 - 2072 2 - 673 2 - 2076 2 - 2077 2 - 2078 2 - 2079 2 - 209 2 - 20
<RODDP:DEST=ALL;EXTERNAL DESTINATION ROUTE DATADEST ROU CHO ADC TRC SRT NUMACK781 1 0005000000000250000 0 4 0 4 1 0005000000000250000 0 4 0 2 2 0005000000000250000 0 4 0 782 4 0005000000000250000 0 4 0 1 1 0005000000000250000 0 4 0 2 2 0005000000000250000 0 4 0
END <LCDDP:TAB=DNT1;NOT ACCEPTEDENTRY NOT FOUND <LCDDP:TAB=DNT2;NOT ACCEPTEDENTRY NOT FOUND
<LCLDP:LIM=ALL;LEAST COST LIM DATALIM AC DEST 1 01895 781 2 01865 782 END <ROCAP:ROU=1&4&2;ROUTE CATEGORY DATAROU SEL TRM SERV NODG DIST DISL TRAF SIG BCAP1 013000000000001 5 2100030001 0 30 128 00151510 111100000020 0011004 011000000000001 5 2100030000 0 30 128 00151510 111100000020 0011002 013000000000001 3 2100030000 0 15 128 00151510 111100000000 001100
END <RODAP:ROU=1&4&2;ROUTE DATAROU TYPE VARC VARI VARO FILTER 1 TL50 H'0000000C H'00000000 H'00000000 NO4 TL50 H'0000000C H'00000000 H'00000000 NO2 TL1 H'00000201 H'00000002 H'00000009 NO
END <RODNP:ROU=ALL;NOT ACCEPTEDDAY AND NIGNOT ASSIGNED
rfpui (TechnicalUser) 16 Mar 04 16:49 HiNow I analyze your’ printout and find one difference between ROU 1 and 4It is position D3 in SEL by ROCAP, try to set D3=3 in ROU =4
And probably you want send RONDP:ROU=ALL; and not RODNP:ROU=ALL;
lancbomb (TechnicalUser) 17 Mar 04 9:04 Hi RFPUI,
re: D3 in sel1 Sequential selection(Even seizure in own LIM and after that the same principle in the next LIM)
3 Sequential selection in route.(First free external line in route. Selection always starts with the same line.)
I dont see how that fixes it,
RONDP print has no entries, however.....
some testing shows, that selecting the dest codes, to other site works. also blocking rou4 will force calls to rou1.
BUT, and this is the case, I dont know if the situation when the links fallen over gives a IDLE and FREE in
the SUSIP print, will then route the calls, as the MD thinks its up ?
I know IDLE and BUSY does work though...
will continue looking, any further ideas ?
cheers
NUTRI PARAMETERSthread806-841003Share This Forum Search FAQs Links Jobs Whitepapers MVPs
Find A Job or Post a Job Opening Click Here.Chukwuemeka (TechnicalUser) 14 May 04 4:30 My client has a direct connect from a public switch and the digits being sent from the switch are 00&&99, while the internal directory is 4001&&4099.Meanwhile, he wants some digits 00&&09&80&&99 to ring at the Operator which is 4000.The other digits will ring at the marching extensionsEg. digit 10 goes to extension 4010 and so on. Note that the Operator number 4000 is also the DISA number. A caller dials 2709700 and expects to reach Operator on 4000 and dials 2709710 and expect to reach extension 4010. How do I set NUTRI parameters.
lalrl (TechnicalUser) 14 May 04 17:28 If a nutri for public route (Euro-ISDN) is already set, then check, that cont=1 is used. Then in my market for conversion of 10 to 4010:
nutri:entry=10,rou=x,cnvtyp=0,numtyp=12,pre=40;
If no nutri exist so far, you must allow numberconversion in route with rocac:rou=x,sel=xxxxxxxxx1;
Chukwuemeka (TechnicalUser) 17 May 04 3:14 Thanks.
It works fine with 4010, but dose not work on 4000.In fact it works well in all extensions but not for operator.
Note that 4000 is an operator.How do I handle Operator setting.
wfhy (TechnicalUser) 17 May 04 4:41 Hello,
You should do-nutri:entry=00,rou=x,cnvtyp=0,numtyp=12,pre=40;-nansi:numtyp=od,numse=4000;
good luck
wfhy
DUFQI (TechnicalUser) 17 May 04 5:23 thats's not the way DID-calls to the operator should be handled.As I read 00&&09&80&&99 are DID numbers to the operator.So initiate these numbers as OI and assign them in OPCTS.nutri:entry=AA,rou=x,cnvtyp=0,numtyp=12,pre=40;has to be done for (AA)1,2,3,4,5,6,7More help
eriuser (TechnicalUser) 26 May 04 5:13 Why use NUTRI at all, just put a PRE of 40 onto the route usingRONDI:ROU=XX,PRE=40;Then assign 4000,4009,4080&4099 as NUMTYP=OD in numanalThen make these numbers goto the switchboard using OPCTS:CORG=YY,CALT=7,ROU=XX,OACC=4000;etc.
Timing on trunkthread806-846359Share This Forum Search FAQs Links Jobs Whitepapers MVPs
Tek-Tips Forums is Member Supported. Click Here to donate.Chukwuemeka (TechnicalUser) 22 May 04 9:31 How can I cut off users on outgoing Trunk lines after some minutes- say Ten minute (10 Min.)
rfpui (TechnicalUser) 22 May 04 18:15 It is not possibleI never heard abut this in MD 110 and other telephony sytem
But if You have BC 12 You can use charging facility for limited call duration/limited cost
CPKC (TechnicalUser) 23 May 04 6:55 Is it analogue trunks?
Chukwuemeka (TechnicalUser) 24 May 04 2:39 1) It exists in MD110 its like a patch.
2) Yes it is on analogue trunk.
CPKC (TechnicalUser) 25 May 04 18:18 You can try this:
If you don't have polarity reversal on trunks from pstn,set SIG D4=1ASPAC:PARNUM=41,PARVAL=600;(600s=10 min)This is work on BC11SP12 AS standard.Good luck
interesting "EXTENSION IS BUSY"thread806-603542Share This
Forum Search FAQs Links Jobs Whitepapers MVPs
vjimeneztenas (Programmer) 15 Jul 03 17:09 Hello all:
Please help me on this:I have a BC10 an when I try to make a
<ksexc:dir=3426,equ=1-1-20-13;
the answer all time is
NOT ACCEPTEDEXTENSION IS BUSY
but the extension is not busy, see this:
<Ctcop:dir=3426;CALL TRACEFROM-CON EQU L>GS-EQU GS>L-EQU TO-CON EQUKL1 3426 001-2-32-15 * NO-CON *END<lscop:equ=1-2-32-15;LIM SWITCH MULTIPLE POSITION DATA EQU ATTN CONNECTION STATUS CONTROLLER ADDRA B LIM UNIT PTR1-2-32-15 NOT CONNECTEDEND <Ctdei:dir=3426;CALL TRACEINITIATED ON DIR: 3426 EQU: 001-2-32-15DEVICE TYPE KL1 PTR: H'01C2MP-IN EQU MP-OUT EQU DEV EQU DEV DIR EQU
* NO-CON * EXECUTED<
what I can do to change that extension?
rrmagno (TechnicalUser) 16 Jul 03 3:30 strange!
rorni (IS/IT--Management) 16 Jul 03 4:07 HiTry "susip:dir=3426"If busy in susip, try to restart klp1t1 in lim1 (during restart phase, all dts will drop calls for 15 seconds)
hope this help/Rorni
vjimeneztenas (Programmer) 16 Jul 03 10:44 rorni,
This is Virgilio,
I did the RFPUI:LIM=1,UNIT=klp1t1; and the problem is the same.the SPEXI show the extension lake FREE
shaun123 (IS/IT--Management) 16 Jul 03 11:34 does the extn have any mdns on it if so if any of these are busy that will give extn busy when trying to move its equ
vjimeneztenas (Programmer) 16 Jul 03 12:13 shaun123,
this is vjimeneztenassee this:
SUdip:dir=3426;DIRECTORY INFORMATION AT 10:07:58 16JUL03DIRECTORY NUMBER : 3426 TYPE OF DIRECTORY NUMBER : DTSNAME : Lopez Gustavo
EXTENSION TERMINAL DATAEQU TERMD ADN CALALT1-2-32-15 0019 1
EXTENSION DIRECTORY CATEGORIESCAT TRAF SERV CDIV ROC TRM ADC CUST LANG0 01000000 00021205 011151000 000001 0 00100010010 F
DIGITAL EXTENSION FUNCTION KEY DATAKEY KTYPE FCN VALUE DIG00 PGM 01 FCN CAB 02 FCN CAD 03 FCN TNS 09 ODN 3426 10 ODN 3426 11 ODN 3426 13 FCN TNS 14 FCN TNS
GROUP DATAGROUP CALL PICKUP: 0026
DIVERSION DATA
INDIVIDUAL ABBREVIATED DIALLING FACILITY DATAINDIVIDUAL ABBREVIATED DIALLING ALLOWED: Y
PAGING DATA
END
can you see? it is not the problem, other suggestion.
shaun123 (IS/IT--Management) 16 Jul 03 14:59 try restarting klp1o in low traffic as this will cut all digi calls in progres the o is the letter o not zero
md110user (TechnicalUser) 16 Jul 03 17:21
hi try to block the extension:bleqi:equ=1-2-32-15;rfpui:lim=1,unit=klp1t1;ksexe:dir=3426;y;
I hope this will solve the problem
vjimeneztenas (Programmer) 16 Jul 03 20:50 Shaun123 and md110user
thanks, but the problem continue,
other suggestion.
vjimeneztenas (Programmer) 16 Jul 03 22:12 Hello all,
this is vjimeneztenas
I solve it, but I did a
RFRLI:LIM=1;
that is not the best way, but it's work.
THANKS TO ALL
jay944 (TechnicalUser) 17 Jul 03 8:37 I dont think you need to restart the whole lim., thats a bit drastic !
sounds like theres corruption
try this,
1> diss of all lines, and stick a digi phone on there, is there DT does it work ??, retsart card and prog unit again
2> sfcei switch
3> block card/unjack card refit restart un block card
what does the blfdp say ? is it in line lock ?Shaun123, do you have the pointers to unlock a locked phone
otherwise I'd say pass to someone who can deal with programm corruptin, if critical, restart lim o o hours
shaun123 (IS/IT--Management) 17 Jul 03 9:17 dont get 2 technical jay944 as ive not touched an md110 since nov last year md whats an md oh i know someone who trys to run a successful company but fails drastically making a quarter of the staff redundant humm sounds fammilar that
vjimeneztenas (Programmer) 17 Jul 03 10:49 Hi jay944,
before restar the lim I did what you said
"1> diss of all lines, and stick a digi phone on there, is there DT does it work ??(it work), retsart card and prog unit again
2> sfcei switch (but I did it after block, unjack and refit)
3> block card/unjack card refit restart un block card"
but nothing, the blfdp said "Individual is blocked as a result of manual blocking of device board via command"
Due to that, I did the RFRLI, but anyway thanks for your tips, and if you know other solution, I listen you.
(the problem is interesting, right!!!!)
jay944 (TechnicalUser) 17 Jul 03 13:53 Shaun, you crack me up <giggles>
vjimenezteanas, ok, so you resatrted the lim after all that and still no joy,,, hmmm,
probably sounds like one of the program units has corruption, restarting the lim will in this case not solve it, hence why I asked shaun if he knew the pointers.
you could try, re-loading that program unit ie klp10, but not done it before so some serious tech boyz need to advise,
I'd also think a rfexi wont do anything,
sorry :(
CEMARG (MIS) 17 Jul 03 16:57 I would pay attention first not to have anything connected in Block-66 or PATCHPANEL. In order to discard a possible short circuit
NANSI (TechnicalUser) 18 Jul 03 11:53 check out my script for WinFIOL in the question DIR xxxx HAS QUE problem.
NANSI
shaun123 (IS/IT--Management) 18 Jul 03 14:55 rfexi and run thatll fix it for good
hdlek (TechnicalUser) 21 Jul 03 4:55 Hi vjimeneztenasIf still this problem occurs you should send BLLTI and RFLII commands to system respectively. Sending this commands will solve this problem.
Best Regards.
hdlek (TechnicalUser) 21 Jul 03 5:05 before doing this,you should change the telephone category with KSCAC command .after this you can the others. If this is not successful you can try other method which I sent you before
Best regards
whosrdaddy (Vendor) 21 Jul 03 16:45 [Quote]vjimeneztenas (Programmer) Jul 16, 2003
Hello all,
this is vjimeneztenas
I solve it, but I did a
RFRLI:LIM=1;
that is not the best way, but it's work.
THANKS TO ALL [/Quote]
As you can read he SOLVED his problem by restarting the lim.Anyway best solution is to restart DERS1 / DER in this caseworks everytime like a charm
Cheers http://www.damovo.com
CIF (TechnicalUser) 11 Jun 04 3:22 Hello,
I was having the same problem with a digital extension running BC12.I solved it thanks to this forum with the following:
bleqi:equ=26-0-52-9;rfpui:lim=26,unit=klp1o;
And it is running OK now.
Regards ...
COMMAND LOST WHEN ROUTE IS PRINTEDthread806-853666Share This Forum Search FAQs Links Jobs Whitepapers MVPs
Tek-Tips Forums is Member Supported. Click Here to donate.REL4 (TechnicalUser) 3 Jun 04 13:23 HI,I HAVE SOME PROBLEMS WHITH ROUTES PRINT .WHEN I GET THE ROCAP, FOR EXAMPLE, DIR=ALL; IT STOPS AT THE MEDLE OF PRINT AND IT RESPONSE WHITH TEXT "COMAND LOST";I THINK THE PROBLEM WAS WHEN WE ERASE ONE LIM IN THE SISTEM WHITHOUT ERASING ROUTE DATA.NOW THERE IS NO ALARMS IN LOG BUT PROBLEM STILL EXISTS, ANY IDEA TO SOLUTINATE THIS PROBLEM?THANKS ALL. AAAAH , ITS BC10...
rfpui (TechnicalUser) 3 Jun 04 18:03 Hiyou send an answer for your problem
It is a consequence of erase LIMLook to Thread806-834623And Thread806-821200
Now solution is to load system from INL and data
REL4 (TechnicalUser) 4 Jun 04 12:03 do you mean... make a new lim disp. whith all the lims again and charge all data in them?
whosrdaddy (Vendor) 4 Jun 04 12:46 scib, contact your local e/// provider they can solve this type of data corruption without the need to remake a complete system... -------------------------------------- What You See Is What You Get
rfpui (TechnicalUser) 4 Jun 04 14:10 Hi allwhosrdaddy have right. It is possible to reappear system by e/// engineersBut who now what else is faultyI have contacts with an e /// engineers and they says it is better to load new system
Scib How big is your system (how many LIMs)
REL4 (TechnicalUser) 7 Jun 04 2:20 hi, there are four lims in system, bc10 paq A , "Ro" are the only commands that fails...
Abbrivated numbersthread806-859795Share This Forum Search FAQs Links Jobs Whitepapers MVPs
md110user (TechnicalUser) 13 Jun 04 13:34 In my PBX MD110 BC12_SP3, I need to put a number and after voice mail answer i need the extension number to be dialed.
e.g: 123456789---123
I need to put all the number on an abbrivated.like 666,but when I programmed it was not dial the Extension number AFTER THE VOICE MAIL MAIN GREETING STARTED ON THE DESTINATION NUMBER??
I tried:
ADCOI:ABB=666,TRA=123456789C123,CLA=0&&3; ORADCOI:ABB=666,TRA=123456789D123,CLA=0&&3; ORADCOI:ABB=666,TRA=123456789E123,CLA=0&&3;
BUT NOW ONE WORKING WELL.
wfhy (TechnicalUser) 14 Jun 04 5:00
HI,CAN YOU DIAL 123 AFTER RECEIVING GREETING?
DUFQI (TechnicalUser) 14 Jun 04 8:19 TRA=...C (D)(E)...is only valid if you receive a PTS (proceed to send signal, like 2nd dialtone).VM systems normally don't send PTS.GreetingsDUFQI
md110user (TechnicalUser) 14 Jun 04 15:32 Thank you Gentelmen;to wfhy Yes I can.
so there is no pause to wait up to the greeting play!!!
TLU76 interworking with CISCO routerthread806-260037Share This Forum Search FAQs Links Jobs Whitepapers MVPs
GuauGuau (TechnicalUser) 25 Apr 02 18:49 Hi!I need to connect an 30B+D ISDN interface of a CISCO router to public ISDN Network. I'm thinking about connecting it to a TLU76, and do transit through MD110 to public ISDN network. I don't know if TLU76 can do that. Can TLU76 emulate public ISDN?
Could anybody help me?
Thanks a lot. Sorry my bad english.
ysgoh88 (TechnicalUser) 26 Apr 02 3:18 Should not be a problem..but you need to tell people what version software of the MD110 is.
GuauGuau (TechnicalUser) 26 Apr 02 10:29
The PBX is a MD110 BC9 Packet B.Thanks a lot.
naltalite (IS/IT--Management) 29 Apr 02 2:25
Should not be a problem. MD110 in BC9 is capable of doing ISDN "Network side".
MD6 (TechnicalUser) 2 May 02 15:24
Hi,
Only TLU76/1 is a ISDN Trunk (public or private). In MD110 have a : TLU76/1--> 30B+D ISDN TLU76/2--> 30B+D DPNSS TLU76/3--> 30B+D CAS TLU76/4--> 30B+D For signalling system no. 7 (ONLY BC11 VERSION)
You define if trunk is a public or private in the MD110 program (ROXXX comands).
Good Work
MD6
ges69 (TechnicalUser) 3 Aug 02 8:54 Yes, tlu 76/1 can.You need to use DSS1 protocoll.
vjimeneztenas (Programmer) 23 Aug 02 19:28 Tell me what kind of cisco and IOS version you have, maybe I can give you a configuration for the cisco and the PABX
mustafa61 (TechnicalUser) 30 Jun 03 5:34 Hi JimenezT,
We are trying to connect the MD110 BC10 to Cisco 2600. We want to seting up a PRI connection between them. Cisco 2600 is using primary net-5 i think. We couldn't establish a connection. Do you have any parameters for both sides. Or do you have any advice like using the q-sig singnalling. Which one do you prefer qsig or pri.
itcom (TechnicalUser) 10 Jul 03 4:38
For connection of MD to CIsco please see http://www.cisco.com/univercd/cc/td/doc/product/access/acs_mod/cis2600/sw_conf/pbx_int/
It is work.
Best regards,Alexey Gusev
GASMAS (Programmer) 14 Jul 03 12:02 We have managed to connect 2 md 110 with Cisco and E1 interface with q sig.Everything works fine.Has anyopne managed to have q-sig functionality with 2b+d interface?
dognbone (Programmer) 16 Jul 03 20:07
I have a site connected to Cisco on a BC9 MD110 using a TLU76/1. Here are the route parameters:-
<ROCAP:ROU=45;ROUTE CATEGORY DATAROU SEL TRM SERV NODG DIST DISL TRAF SIG BCAP45 111000010001 3 3100000000 0 30 128 00151515 111110000031 101100
END <RODAP:ROU=45;ROUTE DATAROU TYPE VARC VARI VARO FILTER 45 SL60 H'00001310 H'15400000 H'06700000 NO
END
I also manage another BC9 site which connects to a Cisco using a TLU79 (2B+D) and its parameters are:
<RODAP:ROU=70;;ROUTE DATA
ROU TYPE VARC VARI VARO FILTER 70 SL60 H'00001144 H'14400000 H'50210000 NO
END <ROCAP:ROU=70;;ROUTE CATEGORY DATAROU SEL TRM SERV NODG DIST DISL TRAF SIG BCAP70 611000001000 3 2100000002 0 30 128 00151515 111110110030 111110
END
Hope this helps.
rrmagno (TechnicalUser) 21 Jul 03 13:43 I've set up a new route for for TLU76/1 on my MD110 with Cisco router 3600.My MD110 version is LZY2035104/1/CNI85D/R1A.the parameters that I set up for this route are as follows:
<ROCAP:ROU=81;ROUTE CATEGORY DATAROU SEL TRM SERV NODG DIST DISL TRAF SIG BCAP 81 012000000000 5 2110000010 0 30 128 00151515 111101100031 001100
<RODAP:ROU=81;ROUTE DATAROU TYPE VARC VARI VARO FILTER81 SL60 H'00000210 H'054A0000 H'06300000 NO
<RODDP:DEST=84;EXTERNAL DESTINATION ROUTE DATADEST DRN ROU CHO CUST ADC TRC SRT NUMACK PRE 50 81 163610000000025000 0 1 0
hope this parameters would help..
vince62s (TechnicalUser) 28 Nov 03 5:01 maybe this will sound ridiculous but:
when connecting a cisco router to a TLU 76 board:
is this for connecting the router to an ISDN type dial up ISP ?
or is it to connect the MD 110 to an existing network ? subsequently, can we do VoIP with this configuration?
thanks guys
SYAR2003 (TechnicalUser) 29 Nov 03 6:13 Vince !See my reply in this threadThread806-703685 setup of md110 qsig networking between e.g twomd's can be utilized with this setup.
TLU76/1 cards connected to cisco ip-router witch havea G.703 interface .That for carrying the tie line(qsig) voice databetween the md's over ip-network.
You will need appropriate data set both for the md'sand in the routers.
SYAR
mdfan (IS/IT--Management) 29 Nov 03 6:36 To make it complete :
G.703/G.704 = E1 (PRA/PRI) .
ok vince ?
SYAR2003 (TechnicalUser) 29 Nov 03 6:43 Yeah!
bram123 (TechnicalUser) 14 Apr 04 4:31 MD110 BC11
I want to connect a TL76/3 CAS Trunks via a Router.
Has anyone had any experience?
Could you provide a quick config overview: any funnies I should be aware
RODAP:ROCAP:RODDP:
Thanks
sakhan (TechnicalUser) 14 Apr 04 9:52 These are the parameters for a route setup with CAS\ TLU76/3. Using it only for outgoing. If somebody need for incoming set VARI.
ROU SEL TRM SERV NODG DIST DISL TRAF SIG BCAP238 001000000000001 5 2100000010 0 30 128 02080812 311110110150 111111
ROUTE DATAROU TYPE VARC VARI VARO FILTER 238 TL30 H'00000000 H'00001216 NO
DEST DRN ROU CHO CUST ADC TRC SRT NUMACK PRE9000 238 00050000000002500000000 0 5 0
Cheers
bram123 (TechnicalUser) 15 Apr 04 5:56 Thanks Sakhan,
Will give it a try when I'm allowed!
As mentioned previously, I've got TL76/1 working Ok... however the returned speech path i.e the called party returning speech back to the Caller appears to degregate...(gets worse)!.....
73vette (TechnicalUser) 19 Jul 04 13:09 Does anyone have the Var's, Rodap, Rocap, Rodap for BC9.0 - TLU 76/3 to a Cisco Router?
Thanks
Trunk selection in "Multi-LIM" routethread806-874536Share This Forum Search FAQs Links Jobs Whitepapers MVPs
Check Out Our Whitepaper Library. Click Here.gedii (Programmer) 6 Jul 04 11:12 Hi
I have a Multi-LIM MD110 with PSTN routes which have members spread accross several LIM's. Some of the LIM's have no members so that when callers dial an External destination code, the call has to switch via the Group Switch to an available route member in another LIM accordingly.
The above all works fine ! If however, I power down LIM's 1 & 2, the LIM's that have no route members present "congestion" to callers dialling out whilst those LIM's with route members process the calls satisfactorily.
It seems to me that this loss of functionality is possibly something to do with "Common Function" program unit(s)in LIM's 1 and/or 2 not being accessible at the time. Is this a correct assumption ?
If so which is/are the concerned program unit(s) and could it/they exist in say LIM's 1 and 5 for example as opposed to LIM's 1 & 2 and function correctly.
Any other theories welcome also !!
Thankyou
gedii.
mundus (TechnicalUser) 7 Jul 04 2:03 Hello Gedii,it's the program DIM, normaly this program is in both lim 2 and 3.
LME (TechnicalUser) 7 Jul 04 14:36 Hi
I think the program unit is DTM
LME (TechnicalUser) 7 Jul 04 14:42 HiHow many LIMs do you have.If you have 5 LIM system then DTM would be in LIMs 3&5.
P.SDIM if for e.g Voice Mail ICU.How are your LIMs sited , are they all on the same site.
LME (TechnicalUser) 7 Jul 04 14:52 Hi If you do CNPIP:UNIT=DTM;It will tell you which LIMs DTM is loaded in.
gedii (Programmer) 8 Jul 04 12:35
Thanks for the advice.
Unit DTM resides in LIM's 2 & 3 which seems ok. The system has 14 LIM's.
I expect DTM should have gone active in LIM 3 immediately on "failure" of LIM 2 in that case ? Could it require a patch ? System is BC10 / CNA143GB. Any other possibilities ?
Cheers
gedii
LME (TechnicalUser) 10 Jul 04 2:49 HiIf you take LIM 2 out of service and do CNPIP:UNIT=DTM;it will show you if DTM is active in LIM 3.If that is the case and you can dial out in the LIM's that have no route members present then it could be a problem with the power down of LIM 1.I dont know how easy it is for you to test this but try to isolate the problem to the shutdown of LIM 1 or 2.
lalrl (TechnicalUser) 10 Jul 04 13:52 I believe, that it is possible to have the unit in LIM1 and LIM5 isstead 1 and 2. The distribution of the units via LIMDISP is in many cases a recommendation from Ericsson.
I´m not sure, but the follow procedure could work:dusii;lapur:unit=,lim=x; (x is lim with the inactive unit)lapul:unit=,lim=5;sfpui...rfpui...sfcei;ladci!!!
But don´t trust me, because it is really systemcritical! Let us hear, what whosrdaddy (god) will tell us...
External Dialtonethread806-895344Share This
Forum Search FAQs Links Jobs Whitepapers MVPs
ursusK (Programmer) 6 Aug 04 9:49 In our MD110 we had before, one could hear a difference in dialtone when it was internal or external.So when a user picked up the phone he would hear a different dialtone if he would press '0' (to get an outside line).
In our new md110 BC12 the dialtone sounds the same inside as outside.
Is there a command to change this? Is this dangerous to do?
Many thanks in advance !
Björn
testcentre (TechnicalUser) 9 Aug 04 2:15 i would check the setting of the SIG parameter in the route category.
ursusK (Programmer) 9 Aug 04 2:27 Sorry, how would i do that? (I'm rather new in de md110 world) :)
MDadmin (TechnicalUser) 9 Aug 04 7:54 Hi ursuk,you could check parnum=254,but rememeber after any changes restart TMU board to activate new tone.
MDadmin (TechnicalUser) 9 Aug 04 7:56 Hi ursuk,you could check parnum=254,but rememeber after any changes you must restart TMU board to activate new tone.
MDadmin (TechnicalUser) 9 Aug 04 7:59 Hi ursuk,you could check parnum=254,but rememeber after any changes restart TMU board to activate new tone.
mduser110 (TechnicalUser) 9 Aug 04 8:04 Hi ursuk,you could check parnum=254, but remember after any changes restart TMU boards to activate new tone.
MDadmin (TechnicalUser) 10 Aug 04 2:40 Hi ursusk,you could check parnum=254,but remember after any changes restat TMU boards to activate new tone.
whosrdaddy (Vendor) 10 Aug 04 3:11 UrsusK :
copy & paste printout of following commands :
RODAP:ROU=x; //replace x with the QSIG route numberROCAP:ROU=x;RODDP:DEST=ALL; -------------------------------------- What You See Is What You Get
ursusK (Programmer) 10 Aug 04 10:14 This is the output.. Hope it helps.. :)
VERSION=CXP1010111/1/BC12SP3/R4A
14:02:52TUE 10 AUG 2004END <RODAP:ROU=ALL;ROUTE DATA
ROU TYPE VARC VARI VARO FILTER
1 SL60 H'00000340 H'10020000 H'24410000 NO2 SL60 H'00000340 H'10020000 H'24410000 NO
END /* SUCCEED 14:02:55 *//* MML_TTY_COMMAND 14:03:35 [NLGBS01] Admin */ROCAP:ROU=ALL;ROUTE CATEGORY DATA
ROU SEL TRM SERV NODG DIST DISL TRAF SIG BCAP
1 7110000000000010 5 3101000101 0 30 128 03151515 511100000030 1111002 7110000000000010 5 3101000101 0 30 128 03151515 511100000030 111100
END /* SUCCEED 14:03:36 *//* MML_TTY_COMMAND 14:03:56 [NLGBS01] Admin */RODDP:DEST=ALL;EXTERNAL DESTINATION ROUTE DATA
DEST DRN ROU CHO CUST ADC TRC SRT NUMACK PRE
0 1 0005000000000250000000000 0 2 0 1 1 0005000000000250000000000 0 2 0 2 1 1 0005000000000250000000000 0 2 0 1 2 0005000000000250000000000 0 2 0
END
TLU76/1 behave as extension card?thread806-906781
Share This Forum Search FAQs Links Jobs Whitepapers MVPs
Find A Job or Post a Job Opening Click Here.ExtensionManager (MIS) 26 Aug 04 8:29 Hi All,
Is it possible to use TLU76/1 as an isdn extension card?If yes, how?
What I´d like:
TLU76 is connected to a Cisco Router.And if our Cisco´s wan line is down the other side router is starting the call to our pbx and get connected our router through the Tlu76.
BC9 software version
whosrdaddy (Vendor) 26 Aug 04 13:48 "isdn extension card" is an ELU26 (s0 bus) in the md110, if you are referring to a ISDN QSIG/PRA then yes, you can use the TLU76/1 -------------------------------------- What You See Is What You Get
ExtensionManager (MIS) 27 Aug 04 3:12 Yes, I mean ISDN pri.How to do it exactly? How to make the routing and programming for terminating the calls on a trunk card?
Number conversion on Analogue trunksthread806-905386Share This Forum Search FAQs Links Jobs Whitepapers MVPs
Check Out Our Whitepaper Library. Click Here.CIF (TechnicalUser) 24 Aug 04 9:21 I am using several analogue trunks but i can not call an internal extension with it.I have tried several different NUTRI conversions but nothing seems to help. The route is ready for incoming traffic.
mundus (TechnicalUser) 24 Aug 04 11:43 Hi' normaly you don't get any digits from the public when using analog trunks, here you can make a DID route ( new dialtone to the public ) and the must dial the extension number, if you want the route to be a manual route then you can use the OPCTS:CORG=x,ROU=x,CALT=5; and OPCGS:CORG=x,DIR=x,CHO=x; if you have an operator, if not you can assign a answer position pr. route or trunk by RONDI:ROU=x,DAY=x,NIG=x; and/or RONDI:ROU=x,TRU=x-x,DAY=x,NIG=x;
Adding a new magazine
thread806-903181Share This Forum Search FAQs Links Jobs Whitepapers MVPs
ogiebendogie (TechnicalUser) 19 Aug 04 15:04 I have a single LIM three high PWM, PSM, IFM. I ordered another IFM to go on top. I have it all bolted on. The new mag has a TMU in slot 10, a DSU in slot 163 and a RG5DC in the far right slot. What are the basic steps to get this new IFM connected and ready to put TLU28s in? It is running BC8 if that matters.
Thanks, Don
whosrdaddy (Vendor) 19 Aug 04 16:35 connect dsu to lsu mag 0power up magenter SFCEI; commandprogram new boards -------------------------------------- What You See Is What You Get
lalrl (TechnicalUser) 20 Aug 04 13:35 ...and control with lscnp
rfpui (TechnicalUser) 22 Aug 04 9:35 HiRecommended procedure is (as whosrdaddy wrote ) but new magazine should be empty only DSU and RG5DC of course After SFCEI and LSCNP plug in all boards and CNHUI:LIM=….
And You have new magazine with TMU and are you have TMU in old magazine?If no, it is not recommended (if I good remember – not possible) to use TMU with TSU-T in this same LIM
ogiebendogie (TechnicalUser) 24 Aug 04 14:55 I connected the DSU to the LSU and ran the power cable down to the power supply. There are DIP switches on the RG5DC that are not on the the other RG5DCs so I'm not sure how they should be set. Any ideas? Also, The other RG5DCs have another cable attached (alarm?) do I need this one?
Thanks,Don
rfpui (TechnicalUser) 24 Aug 04 15:06 Are you shure that you have RG5DC on your "old" magazine?I thing that You have PU4DC and not RG5DC
ogiebendogie (TechnicalUser) 24 Aug 04 15:55 Sorry it is PU4DCs in the old mags. The old mags also have their own TMUs.
Thanks,Don
rfpui (TechnicalUser) 24 Aug 04 16:49 I’m againHave you Alex?So, PU4DC is only Power Unit and You have REU board in LIMRG5DC is a board which replace REU board and PUxDCThis “other cable” from one PU4DC to other PU4DC is a ring signal link.Find a REU board and look how are jumper are set. Ring voltage and cadence
And set Dip switches on new RG5DC for this same combination as REU
How can I erase generic extensions thread806-912540Share This Forum Search FAQs Links Jobs Whitepapers MVPs
Check Out Our Whitepaper Library. Click Here.rokane (TechnicalUser) 6 Sep 04 22:00 How can I erase generic extensions when the LIM where the data are stored is already ended.It was erased with out knowing that some generic extensions data are stored in this lim.Can anyone pls help me how to clear this problem. I can't erase & prints data for those generic extensions the system always response is command lost.
wfhy (TechnicalUser) 6 Sep 04 23:35 Generic extension is a concept introduced in ASB 501 04. It is affiliated to an application such as Cordless, IP and RE extension. To delete a generic extension, you must delete the application. I give a exzample for Cordless:
CXAKE:DIR=;GEDIE:DIR=;CXRFE:FPI=,RPN=;CXCFE:FPI=;
Good luck!
rokane (TechnicalUser) 7 Sep 04 0:18 Wfhy,
The problem is that when the generic extension was intiatedthe data was stored in LIM 12 but for some reasons LIM12was removed not knowing that generic extension data werestored on this LIM 12. So when the command below is entered we got this respond command lost.
<gedip:dir=3348;WAIT WAITWAITWAITWAITWAITWAITWAITWAITCOMMAND LOST
<gedii:dir=3348,lim=12,csp=0;NOT ACCEPTEDDIR=3348 ALREADY ASSIGNED
singhbrindisi (TechnicalUser) 7 Sep 04 8:43 Hi,
If possible put one Dummy LIM as LIM12 & delete all the info about it,
BR, The truth about action must be known and the truth of inaction also must be known; even so the truth about prohibited action must be known. For mysterious are the ways of action.
rokane (TechnicalUser) 7 Sep 04 11:18 Hello,
Is there another way to do it without putting back the LIMagain?...the lim was already sent away to a remote site.
rokane
rfpui (TechnicalUser) 7 Sep 04 11:25 It can be other LIMfor examle one magazine with LPU LSU and DSU
rokane (TechnicalUser) 7 Sep 04 11:40
Do I have to do the same procedure as adding new lim for this one lim magazine as lim 12?
rokane
rfpui (TechnicalUser) 7 Sep 04 12:06 Yes
rokane (TechnicalUser) 7 Sep 04 12:19
thanks, I give you feedback on what happen.
rokane
rokane (TechnicalUser) 11 Sep 04 2:57 RFPUI,
I already returned the lim in the system, now how do I remove the generic extension or update the data base incurrent status?
rokane
rezal (Programmer) 11 Sep 04 8:29 z
rezal (Programmer) 11 Sep 04 8:35 I have had problems posting, that's why I did the test above.
Anyway if You ended a LIM without properly removing all dataYou basically have two options.1. Find an old dump with that LIM on and reload it.2. Try to print as much data as You possibly can regenerate it with PCREGEN and start from INL.
/rezal
rokane (TechnicalUser) 12 Sep 04 6:20 rezal,
The old dump is gone & if I use inl to load the system a newit will take so much time to restore it back & this will beun acceptable to the client having more than 4000 extensions. What I want is to be able to remove the datacorruptions with very minimal service interruptions. Theproblem I am having is as follows;
KSDDP:DIR=ALL; got command lost at certain pointsEXDDP:DIR=ALL; - same -RODAP:ROU=ALL; - same -ROCAP:ROU=ALL; - same -GEDIP:DIR=ALL; - same -GEDIE:DIR=xxxx; - same -
rokane
fcpli (TechnicalUser) 12 Sep 04 7:32
rokane!the corruption is surely in DEM (or DED), depends of yourBC release. This unit knows in which LIM an extension is located. Now you have to know, which directory numbers where located in LIM12. Then with a SGSAI that particular directory number can be removed from DEM data. But first of all, find out the numbers, somehow. One way is to print out e.g. excap:dir=xxxx, then dir=xxxx+1 and so on, until you get command lost. Of course, with 4000 extensions this is a hard task. But when you have the numbers, this can be cleared. There could also be some other data corruption, but try to solve this first.good luck!
rokane (TechnicalUser) 12 Sep 04 19:44 fcpli,
I already got those extensions, can you give me the exact command/s & procedures on how to do it.The MD110 softwareversion is BC11 SP9.
rokane
fcpli (TechnicalUser) 13 Sep 04 8:50 OK.
So, try with one extension first: Clear history (hirei). Print out one extension, which gives command lost. Then SGSAI and SGSSI. Print again, if no command lost, proceed. Otherwise send HIMDP.
sgsai:sigar=1,signo=129,level=b,lcside=exe,stype=swsw,unit=der,lim=1,byte=0-0&1-0&2-1&3-a8&4-c&5-ff&6-x1&7-x2&8-x3&9-x4&10-x5;sgssi:sigar=1;
x1-x5 is the directory numberbyte 4 is the LIM number, which is missing (c in your case)byte 5 = ff removes the info from the unit
below also a trace of this procedure
(H'0129) FROM SGR (H'00A6) EXE A IN LIM 001TO DER (H'017D) EXE A IN LIM 001WITH 0 1 2 3 4 5 6 7 8 9 000 H'00 H'00 H'01 H'A8 H'0C H'FF H'02 H'00 H'00 H'09 010 H'0F H'02 H'00 H'07 H'4C H'02 H'00 H'06 H'00
Note! Every directory number has to be removed separately!
summerdike (Instructor) 14 Sep 04 16:17 Why not try SFEXI;
in the evening
______________________________"Reload and Restart RequestedSystem Initiated"
fcpli (TechnicalUser) 15 Sep 04 1:38 SFEXI???? Maybe ALLIP?Forget it!!!!!
rezal (Programmer) 15 Sep 04 9:25 There may be data mismatches all over the place. It entirilydepends on what data that was left. Rocap and rodap doesn'thave any data dependencies to generic extensions. Thisimplies that more then just generic extensions was left.This system is very sick and You will probably have loadsof problems with any move add and change.
Unaccaptable or not At this point You don't have much choice. You must try to rescue as much data as possibleand rebuild it from there.
If You have a service contractract You may be ableto buy some time from Ericsson to help You. Good luck
/rezal
summerdike (Instructor) 15 Sep 04 11:16 I think Rezal is right about the fact that you can not trust the system anymore. Mismatches all over the place. If you start messing around in that it is hard to get it any better then it is.
Let the system clean up things by command, in a simple way (i.e. SFEXI or other command).
If that don't work build it again in a proper way. Which can be best done at a service center where they can simulate your system and dump it ta Disk.So....Get BC11 sp 9 INLGet license fileGet lim dispositionMake PC-regen of the current system (skip the unwanted extensions etc.).
Start "new" PBX!
______________________________"Reload and Restart RequestedSystem Initiated"
fcpli (TechnicalUser) 15 Sep 04 16:40 rezal, summerdike:Rokane wants to save the system as it is. SFEXI is only possible after first initial load, making a new system with INL, maybe not very clever in this case. If your opinion isto just give advices, which are counted to zero, don't bother, it's only a waste of space. If he wants to try this, OK. The RO case can also be solved, but first the DE case, and there are some other things also, so let's begin with this one, OK?
rezal (Programmer) 16 Sep 04 5:42 fcpli: It is NOT a good advice to leave the system like this. I would certainly not do that to any of my customers. This kind of stuff will give You headaches for a long time. The only sensible thing is to rescue as much data as possible and then rebuild it. After this I will not waste more space on this issue...
/rezal
rokane (TechnicalUser) 17 Sep 04 5:05 fcpli,
The gedip:dir=all; command is now okay, no more command lost after doing SGSAI. How about the procedures for rocap,ksddp & exddp I still experience command lost on these.
rokane
fcpli (TechnicalUser) 17 Sep 04 7:21 rokane!
Actually you can use the same SGSAI for the EL and KL, but to be accurate, change byte 3 to 99 for EL and to c2 for KL (3-99 or 3-C2). After the extensions are OK, there remains RO (at least). A good idea is to use pcregen to print all data out, and check where you got "command lost". Good luck
rokane (TechnicalUser) 17 Sep 04 8:40 fcpli,
Can you also give me the procedures for the route so I can do it at one time onsite.
thanks.
rokane
fcpli (TechnicalUser) 17 Sep 04 9:58 To erase the routes is a little bit tricky. What we need to know, is the reference pointer of the rou which is/was in the removed LIM. How to find it/them:1) With CNPIP:UNIT=DTM; check where the active unit resides.2) Then SACOP:UNIT=DTM,LIM=x,RELOFF=9,FILNO=1,POINT=0&&9c3; Where x is for the active DTM LIM. The printout is HUGE (2500 records), but don't care! Now, in the data, is the LIM number (in your case 12 -> 0C). Write down all thepointers, which point to LIM 12. 3) Now, to be sure that you are on the right track, sacop those pointers mentioned above withSACOP:UNIT=DTM,LIM=x,RELOFF=6&7,FILNO=1,POINT=xyzw; This sacop results in route number (HEX). If you have the information of them somewhere, it is good to check that they are correct.If OK, just a SGSAI remains. But first insert the sacops here (not the long one, just those pointers you need to "kill"). Have a "nice" weekend!
jazaya (Instructor) 18 Sep 04 6:56 To Fcpli:Nice to see you back in action.Please check your mails too.When i read your comments,they make me think you are a magician.
singhbrindisi (TechnicalUser) 18 Sep 04 8:13 I agree with Jazaya....FCPLI is a busy magician moving all around the globe....
BR, ""The truth about action must be known and the truth of inaction also must be known; even so the truth about prohibited action must be known. For mysterious are the ways of action""
rokane (TechnicalUser) 19 Sep 04 20:29 Fcpli,
Thank you very much for help extended it is very much appreciated. My problem is now okay.
rokane
fcpli (TechnicalUser) 21 Sep 04 17:17 rokane:OK, you are almost lucky now!So, what abot the RO part? Also, in order to get the data completely OK (as some people were concerned about), just check with PCREGEN that you don't receive any "COMMAND LOST" messages. Also check from HIMDP that the history does not show any faults (unusual ones)or lost LIMs. If all this seems to be OK, you are saved!
ps. There might also be GH or CH parts wrong here, check!
CENTRALIZED OPERATOR
thread806-923116Share This Forum Search FAQs Links Jobs Whitepapers MVPs
Chukwuemeka (TechnicalUser) 24 Sep 04 7:48 What are the requirements for initiating a central operator for three Exchanges tied together say A, B & C, with the Operator residing at A Exchange.
Isinor (Instructor) 24 Sep 04 8:28 Hi,
If you have access to Alex...
Basic Exchange ..Operation and Maintenance ACS ..General ..Centralized answer position ..Paragraph 14 has an example
If your existing system has Node ID's and links with network services e.g. call back working, it's not that hard to do.
RegardsIsinor
patcher (TechnicalUser) 30 Sep 04 23:35
This is an example and I used DPNSS. Programming is very similar./patcher
/* LIM-A-BC90 */KSTSC:STRNO=IDL1,STRING=" NODE-A";@/EXEC/KSTSC:STRNO=IDL12,STRING=" NODE-A";@/EXEC/
NANSI:NUMTYP=EX,NUMSE=3000&&3099;@/EXE/NANSI:NUMTYP=ED,NUMSE=1&4&701;@/EXEC/NANSI:NUMTYP=EN,NUMSE=700;@/EXE/NANSI:NUMTYP=OI,NUMSE=3999;@/EXE/NANSI:NUMTYP=OD,NUMSE=5300&0;@/EXE/NANSI:NUMTYP=OC,NUMSE=0;@/EXEC/NANSI:NUMTYP=AC,NUMSE=51;@/EXEC/
EXCCS:CAT=15,TRAF=00151515,SERV=02021201,CDIV=011150000;@/EXEC/
ROCAI:ROU=50,SEL=712000000000,SERV=2110030000,TRAF=00151515,TRM=5,SIG=111100000011;@/EXEC/RODAI:ROU=50,TYPE=TL50,VARC=00000000,VARI=00000000,VARO=00000000;@/EXEC/ROEQI:ROU=50,TRU=1-1&&1-5,EQU=1-0-30-01;@/EXEC/
RODDI:DEST=4,SRT=1,ROU=50,ADC=0606000000000250;@/EXEC/RODDI:DEST=701,SRT=1,ROU=50,ADC=0606000000000250;@/EXEC/
OPERI:DIR=3999,EQU=1-0-22-00,TRAF=1515,OPC=10,PRG=1,TYPE=1;@/EXEC/
OPCTS:CALT=1,CORG=1,OACC=0;@/EXEC/OPCTS:CALT=2,CORG=1,OACC=0;@/EXEC/OPCTS:CALT=3,CORG=1,OACC=0;@/EXEC/OPCTS:CALT=6,CORG=3,OACC=5300,ROU=50;@/EXEC/OPCTS:CALT=6,CORG=3,OACC=0,ROU=50;@/EXEC/OPCGS:CORG=1,CHO=1,DIR=3999;@/EXEC/OPCGS:CORG=2,CHO=1,DIR=3999;@/EXEC/OPCGS:CORG=3,CHO=1,DIR=3999;@/EXEC/
ADCOI:ABB=51,TRA=7010,CLASS=0&&3;@/EXEC/
OPCEI:CORG=1,PRIO=1,NCA=701,CENUM=51;@/EXEC/OPCEI:CORG=2,PRIO=1,NCA=701,CENUM=51;@/EXEC/OPCEI:CORG=3,PRIO=1,NCA=701,CENUM=51;@/EXEC/RORNI:ROU=30,PRIO=1,NCA=701,NUM=51;@/EXEC/OPNEI:OWNID=700,NEXGNO=701;@/EXEC/ASPAC:PARNUM=64,PARVAL=0; ! TO ACTIVATE COP ANSWERING POS !YES;@/EXEC//*-------------------------------------*//* LIM-B-BC90 */KSTSC:STRNO=IDL1,STRING=" NODE-B";@/EXEC/KSTSC:STRNO=IDL12,STRING= "NODE-B";@/EXEC/
NANSI:NUMTYP=EX,NUMSE=4000&&4099;@/EXE/NANSI:NUMTYP=ED,NUMSE=1&3&700;@/EXEC/NANSI:NUMTYP=EN,NUMSE=701;@/EXE/NANSI:NUMTYP=OI,NUMSE=4999;@/EXE/NANSI:NUMTYP=OD,NUMSE=5400&0;@/EXE/NANSI:NUMTYP=OC,NUMSE=0;@/EXEC/NANSI:NUMTYP=AC,NUMSE=51;@/EXEC/
EXCCS:CAT=15,TRAF=00151515,SERV=02021201,CDIV=011150000;@/EXEC/
ROCAI:ROU=50,SEL=712000000000,SERV=2110030000,TRAF=00151515,TRM=5,SIG=111100000011;@/EXEC/RODAI:ROU=50,TYPE=TL50,VARC=00000003,VARI=00000000,VARO=00000000;@/EXEC/ROEQI:ROU=50,TRU=1-1&&1-5,EQU=1-0-30-01;@/EXEC/
RODDI:DEST=3,SRT=1,ROU=50,ADC=0606000000000250;@/EXEC/RODDI:DEST=701,SRT=1,ROU=50,ADC=0606000000000250;@/EXEC/
OPERI:DIR=4999,EQU=1-0-40-00,TRAF=1515,OPC=10,PRG=1,TYPE=3;@/EXEC/OPCTS:CALT=1,CORG=1,OACC=0;@/EXEC/OPCTS:CALT=2,CORG=1,OACC=0;@/EXEC/OPCTS:CALT=3,CORG=1,OACC=0;@/EXEC/OPCTS:CALT=6,CORG=3,OACC=5400,ROU=50;@/EXEC/OPCTS:CALT=6,CORG=3,OACC=0,ROU=50;@/EXEC/OPCGS:CORG=1,CHO=1,DIR=4999;@/EXEC/OPCGS:CORG=2,CHO=1,DIR=4999;@/EXEC/OPCGS:CORG=3,CHO=1,DIR=4999;@/EXEC/
ADCOI:ABB=51,TRA=7000,CLASS=0&&3;@/EXEC/
OPCEI:CORG=1,PRIO=1,NCA=700,CENUM=51;@/EXEC/OPCEI:CORG=2,PRIO=1,NCA=700,CENUM=51;@/EXEC/OPCEI:CORG=3,PRIO=1,NCA=700,CENUM=51;@/EXEC/
RORNI:ROU=30,PRIO=1,NCA=700,NUM=51;@/EXEC/
OPNEI:OWNID=701,NEXGNO=700;@/EXEC/
ASPAC:PARNUM=64,PARVAL=1; ! TO ACTIVATE THE COP ANSWERING POS !YES;@/EXEC//*-------------------------------------*/
md110user (TechnicalUser) 1 Oct 04 16:20 PatcherYou are a Great manThank you Sir.
lalrl (TechnicalUser) 2 Oct 04 4:36 few questions:
1. Which Node has now the centralized operator? Or is one opi the substitute for a nightswitched opi in the other node?2. In Node A you have abb=51 with tra=7010. But couldn´t we avoid the extra dest 701, if we use the 4 for our purposes? Because now a user in Node A has 3 possibilities to dial to node B: 4, 701 and 51. How to reduce this?3. What happens, if both opi are nightswitched. Shouldn´t we have opadc or rodni?
patcher (TechnicalUser) 3 Oct 04 17:06 Well, any node can be an aswering point depend on parnum 64 and the above example was initiated for both nodes and controlled by parnum. If you need one-way only then initiate one side only. Both 51 and 700/701 is needed for different signalling. Remember the above example is an example. Your numbering scheme is probably different but the logic is same. /patcher
power failure by dsuthread806-928728Share This Forum Search FAQs Links Jobs Whitepapers MVPs
tomd110 (TechnicalUser) 5 Oct 04 4:06 hi to everybody
in my 3 lim bc9 system i have a class 4 alarm
102 power failure detected by dsu in lim 2 magazine 0
(only lim 1 has duplicated dsu's per magazine)
everything seems to work fine
so what's up ?
lancbomb (TechnicalUser) 5 Oct 04 5:27 try this first,
ALDAR:CODE=102;ALREI;ALDAS:CODE=102,CLASS=4(CLASS could be CLA, sorry from memory)
if real power alarm, it will come in again.
whosrdaddy (Vendor) 5 Oct 04 10:09 tomd110,
forget lancbomb's reply as the alarm WILL come back.
can you provide us a printout of the alarm (ALLOP;) the INFx paramater will provide enough info to determine what's wrong.
I suspect one of the voltages on your PU4DC/RG5DC is missing. You can test this yourself by measuring the voltages on the testpins.
lancbomb, stop using the ALDAR command, as it really doesn't make any sense using this command unless you intent to delete some anoying alarms like code 38. -------------------------------------- What You See Is What You Get
mdman (TechnicalUser) 5 Oct 04 10:15 The alarm indicates that there is a power missing from the power board in LIM 2.The correct action is to measure which power is actualy missing (this is usually stated in the ADDINFO).If power is missing your power board is probably broken.
If all power is correct you should replace the DSU board since that could be faulty as well.
The reason you don't notice aything is because there might be power missing that your are not using. F.e. there is a ringing voltage for analoge phones. If there are analoge phones in the magazine they might not have ring tone etc. anymore, if there are no analoge phones in that magazin you will not notice naything wrong.
Question to Lancomb, why are you always using ALDAR and ALDAS? For solving alarms you never need these to commands.
mdman (TechnicalUser) 5 Oct 04 10:26 Here the meaning of the ADD Info's for alarm code 102
ADD INFO 1: 0 - 3 = States DSU ADD INFO 2: 0 = DSU board is missing -5V 1 = DSU board is missing +12V 2 = DSU board is missing -12V 3 = DSU board is missing -48V 4 = DSU board is missing RGA (ringing voltage)
lalrl (TechnicalUser) 5 Oct 04 11:41 In the most cases REU-Board is the problem. Use cnrec to correct this.
tomd110 (TechnicalUser) 5 Oct 04 15:14 for i've already done what lancbomb suggested (aldar/aldas)the class4 alarm didn't come back
the addinfo of the 102 error was 102 power failure detected by dsu
alp noif equ inf1 inf2
1 1 002-0-**-** 1 2
parnum (TechnicalUser) 5 Oct 04 15:28 REU & CNREC is only applicable if the addinfo is 4 and the lim can't see the ringer voltage. In this case it's 2 which is loss of -12v in lim 2 mag 0, so check the voltage on the power card. the alarm will come back overnight i bet... as you have duplicated processor with no spare DSU slot you will have to swap out the faulty power card by powering the magazine off first.
whosrdaddy (Vendor) 5 Oct 04 15:31 tomd110,
just to make this clear :
addinfo 1 (inf1) states the magazine where the voltage is missing. so in your case the problem lies in magazine 1 -------------------------------------- What You See Is What You Get
patcher (TechnicalUser) 5 Oct 04 16:20 Lancbomb, I mostly noticed that your recommendation is to ALDAR the code. Is this the way you fix your problem??? Poor ericsson customer your working for.
apacheMD (TechnicalUser) 6 Oct 04 0:51 Hi
Try this.
CNREC:LIM=X,REU=NO;
br//
APACHE
lancbomb (TechnicalUser) 6 Oct 04 5:02 Dear all,
I give advice, you "dont" have to take it.The advice I give is on my experince working for /// and D.
We "all" have ways of going about resolving problems, given the fact that the information we get for faults, is usually only about 10%, misquoted, with no prints and sometimes not even written down properly.
We dont even get a list of what people have done to diagnose/resolve the fault, before it gets here.
If a suggestion doesnt work then come back and I can help further.
This was origianlly reported with no information or prints, in my experience the Aldar works, if it is a "real power alarm" it will come back. I should have added that.
Pls check all voltages etc to proove that this is not a major power alarm. But hey I'm just human and would assume somone has done this.
SO I really would appreciate less of the negative comments
cheers
LB
So I'd appreciate less of the "why do you" comments
whosrdaddy (Vendor) 6 Oct 04 5:51 we're just reacting because using aldar is not the normal procedure, that's all... -------------------------------------- What You See Is What You Get
tomd110 (TechnicalUser) 6 Oct 04 9:16 after 24 hours the class4 102 alarm is back
this time with addinfo inf1 = 0
after measuring i found the -12V on the PU5DC board in mag0 and mag1 missing
snakeblitsen (Programmer) 10 Oct 04 8:38 Hi,On one site I maintain remotely remotely, I was getting a power alarm class 4 code 769 alp1 noif 1. An engineer was sent to the site and the PU4DC and ALU1 was changed but the alarm remained. I read LANCBOMB's tip about ALDAR - removed it , replaced it and the alarm is now clear. Don't knock experience -- 'TIPS' is what it is all about. Not a lot of us speak PLEX.Thanks Lancbomb.Cheers
lancbomb (TechnicalUser) 11 Oct 04 4:24 hi,yeah, from my perpective, there are different fixes for the same thing. I've had faults where I've followed the book, then PSG help, only to get nowhere, then "as if by magic" the fault clears on "I'll try an Alrei one last time !"
Go figure ?
I have no "in-depth" explanation, however it seems to me that this wonderfull MD, tends to get its knickers in a twist at times.
I'm sure that you can fix problems with SACOP'ing, a full in-depth PLEX diagnostic and other magical spells. BUt sometimes the simple things work too.
I was told that little pearl when I was out in the field, ohh around 4 years ago, and someone did give me a reason why it works, but it does, I've also seen it work on other things.
Of course any power fault (and other fault) should alway's be checked properly. but if it works dont knock it, and if it doesnt work, come back and we'll try and help further,
cheers for the comments snakeblitsen ;)
take care all
happy MOnday (its going to be another long week) ;)
Avstral (TechnicalUser) 11 Oct 04 19:46 My 2 cents to support lancbomb.
I've 4 sites with VERY old hardware, currently loaded as BC10.Every 2-3 month some LIMs there start to generate 102 and 104 alarms referring to Mag 3.
But there are only 2 (two) magazines in every LIM....Very clear software glitch, from my point of view.
Should I spend a time with fault investigation if the customer is happy with current antic version and HAVE NO REAL TROUBLES, affecting trafic?
ALDAR+ALREI+ALDAS -->alarm gone for next couple of month.
And who will kick me for this?Regards
Change IP adressthread806-944593Share This Forum Search FAQs Links Jobs Whitepapers MVPs
Cascais (TechnicalUser) 2 Nov 04 8:53 Hello,
I'm a new user of this forum and I'm writing from Portugal.How do I change the IP adress of my MD110 BC11 ?Could anyone help me ?
Thank you very much,
P.S. I'm sorry about my english.
rfpui (TechnicalUser) 2 Nov 04 9:19 From Alex:IONPC:EQU=...,IP=...;orIONPC:EQU=[IP],[MASK],[GATE];
The command is used to change the network configuration of a physical I/O port on the NIU/NIU2. The network configuration must be changed prior to using IOEQI to initiate a logical network port. Only the
parameters that get a new value will be changed, other parameters will keep their existing values.
Once the network port configuration is defined it can be reset by specifying IP equal to NONE. The IP address of the I/O port, the IP address of default gateway, and the address mask will be reset to default values indicating that the network port configuration has not been set.
EXAMPLE 1 Change IP address of the Ethernet port at position 1-0-23-4 to 204.94.208.0.
< IONPC :EQU=1-0-23-4,IP=204.94.208.0; EXECUTED IONCP; to printout IP settings
summerdike (Instructor) 3 Nov 04 5:34 To let it work with the newe Ip address , key the command RFBOI....
This is what Alex "says":
Network port configuration 6.7.1 Changing the network configuration of an I/O port General
The following configuration of a port on the NIU/NIU2 (individual 1 to 4) can be changed:
IP address of the port IP address of default gateway Address mask Prerequisites
The port must not have been initiated with command IOEQI .
Execution
Key command IONPP to print out the current network configuration of the port.
Key command IONPC to change the network configuration of the port.
Key command RFBOI to restart the I/O board.
Key command IONPP to verify that the network configuration of the port has been changed.
______________________________"Reload and Restart RequestedSystem Initiated"
Analoque Trunksthread806-947876Share This Forum Search FAQs Links Jobs Whitepapers MVPs
notsniw (TechnicalUser) 8 Nov 04 8:25 Hi all;we have a problem with the audio level on the analoque trunks.My customer external analoque lines with audio level is very poor.System is Md110 bc12 sp5.Does any one knows workaround solution for this case?Thanks ....
rfpui (TechnicalUser) 8 Nov 04 9:07 First step is to change TRM value in ROute categoryROCAC:TRM=y, ROU=x;X is your analog route and Y value from 4 to 7.
asuvp (Programmer) 8 Nov 04 9:30 You can check the attenuation with LSCOP.
Make a call where the trunk and extension areconnected and enter LSCOP:LIM/EQU=xxx; andyou can see what you have today.
Note! do not confuse the ATTN value in the printoutwith the TRM value.The TRM is usad as index in a matrix where the ATTN isread from.
md110user (TechnicalUser) 8 Nov 04 9:37 Hi SIrrfpui is right but to add more:
Second step is to change TRM value in EXtension categoryEXCAC:TRM=y, dir=xxxx;X is your analog Extension and Y value from 0 to 3.and the defult is trm=0 try to increase it to 3, it will increase the level fpr internal and external calls.
I hope that will help.
asuvp (Programmer) 23 Nov 04 4:48 Here is a try to explain how the TRM parameter is used.
Below is a printout of the transmission matrix with SACOP(variable CTRANSPARMAT in SCP) from BC11-SP10.And a printout of the attenuation values used in LS(command LSATP).
If the matrix from the printout below is reformatted itlooks like this:
0 1 2 3 4 5 6 70 02 02 02 02 02 02 02 021 02 02 02 02 02 02 02 022 02 02 02 02 02 02 02 023 02 02 02 02 02 02 02 024 02 02 02 01 03 03 04 035 02 02 02 02 03 02 03 036 02 02 02 02 04 03 04 03
7 02 02 02 02 03 02 03 02
The rows is the TRM value for the sending partyand the column for the receiving party and the values inthe matrix is the attenuation used when the connection inthe LIM switch is setup.
Example:A extension with TRM=3 and a trunk with TRM=4 are connectedthen the switch path from the extension to the trunk hasATTN=2 (0 dB), and from the trunk to the extension ATTN=1(-3 dB (this means that the connection is amplified)).
Notes:1. the values in the matrix is market dependent.2. with sacos I have changed the values at (4,3) to 1, it was 2 before.
<sacop:unit=scp,Lim=1,sector=rel,addr=51&&90; MEMORY CONTENT ON ADDRESS POSITION EXE A
ADDRESS 0 1 2 3 4 5 6 7 8 9 A B C D E F ISO 00000050 01 02 02 02 02 02 02 02 02 02 02 02 02 02 02 02 ................ 00000060 02 02 02 02 02 02 02 02 02 02 02 02 02 02 02 02 ................ 00000070 02 02 02 02 01 03 03 04 03 02 02 02 02 03 02 03 ................ 00000080 03 02 02 02 02 04 03 04 03 02 02 02 02 03 02 03 ................ 00000090 02 FF FF FF FF FF FF FF FF FF FF FF 26 43 4F 50 ............&COPEND
<lsatp;LIM SWITCH ATTENUATION (DB)POS 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15------------------------------------------------------------------------LIM 1 -6 -3 0 3 6 9 12 15 18 21 24 27 30 33 36 39
END
lancbomb (TechnicalUser) 23 Nov 04 5:00 didnt some of the cards also have links on them ??
TLU76 programming question thread806-960319Share This Forum Search FAQs Links Jobs Whitepapers MVPs
rightsaidfred (TechnicalUser) 1 Dec 04 8:55 Hi All,
How to program a TLU76/1 card if it is connected to an external device? (voicemail or conference system or whatever)And signalling is qsig, or isdn.How will I be able to call the channels of this route?It´s dest code handles it like "group hunting group"?
Thanks
cuneyt2919 (TechnicalUser) 1 Dec 04 9:10
Hi it depends on the system, which you use as an external system and what the external system support as a protocol..
Generally for IVR or call detection systems , DPNSS or CAS is used... (TLU76/2 or 76/3)But also it's possible to use qsig or euro-isdn with external systems But if you use tlu76/1 then you should use qsig or EURO ISDN
If the external system will use md resources (ie. ext. system will make call thru Md system you should better to configure md as master and external system as slave.)
rightsaidfred (TechnicalUser) 1 Dec 04 9:46 What, if I want external callers to call did in external system?Shall they call the dest code, and make it did? ANd this one channel is getting offhook?
Operator Boardsthread806-960294Share This Forum Search FAQs Links Jobs Whitepapers MVPs
mack27 (Programmer) 1 Dec 04 8:20 Hi all,
Since we have upgrade from BC9 to BC11 we have an intermittent fault accross our operators boards on different lims they cannot hear customers.The usual resolution is to restart the boards this brings them back.Any ideas, we have upgraded the SP on the boards this has not resolved the problem.
pelpi1234 (TechnicalUser) 1 Dec 04 8:40 HiCheck Tmu boards. They should be Rof 1375335/2 R3A.
mack27 (Programmer) 1 Dec 04 8:59 pelpi1234 the TMU boards is ROF1375335/2 R3A
pelpi1234 (TechnicalUser) 1 Dec 04 9:42 Hi
Then of the Tmu's has to be faulty.Try and change the TMU board where the opi are connected.
Regards
patcher (TechnicalUser) 1 Dec 04 22:37 Its not TMU... Its more likely the revision of CTI adaptor or the telephone set connected to OWS. Is it OWS?
Avstral (TechnicalUser) 1 Dec 04 23:45 There was service advice from E/// about problems with OPI on the base of DBC213, 214 and 314 initiated on ELU25.
ELU25 must be swapped to ELU28.
Sorry, if this is your case..
Regards
mack27 (Programmer) 2 Dec 04 8:51 Avatral the boards are on an ELU28, Patcher they are OWS I do not beileve it is a problem with the CTI adaptor when the program units are restarted this brings back the boards
mack27 (Programmer) 2 Dec 04 10:00 My mistake Patcher the boards are OPI-11
Avstral (TechnicalUser) 2 Dec 04 19:17 mack27,
Buddy, your question looks exactly like this:"Doctor, I'm sick. Do you have a pill for me???"
If you need a help, why shell we gess about your simptoms?About your SP, boards and OPI revisions, programming.........
Anyhow, in SP14 there was a correction S101255A on OLP1Twith the description "No Speech between OPI and left party after Recall".
And if you have earler SP, first logical advice will be - upgrade your MD to latest possible SP. For BC11 this is SP14.
Regards
H323 TRUNKthread806-956774Share This Forum Search FAQs Links Jobs Whitepapers MVPs
Check Out Our Whitepaper Library. Click Here.notsniw (TechnicalUser) 24 Nov 04 3:36 Hi all,I ve md110 bc12 sp5.There are two sites.Everything is ok,good working.My problem is licence.EXTERNAL-LINE-H323-SERV FAL 1043611.What is the licence.What can i do.ALLIP;DATE: 24NOV04 TIME: 10:14:30CODE CLASS NOAF EXPLANATION
38 1 1 DISTURB. COUNTER INCREASED DUE TO FAULTY PROGRAM EXECUTION120 4 1 TOO MANY LICENSES ALLOCATED121 1 1 LICENSE SERVER BLOCKED
whosrdaddy (Vendor) 24 Nov 04 4:06 you have ip trunking initiated(in trial period) while you have no licenses for it.
2 options : 1) buy the license 2) deprogram ip trunk ->
check rodap:rou=all; and check for a route with type TL65deprogram all trunks of this route : roeqe:rou=xx,tru=y-zz;
cheers
-------------------------------------- What You See Is What You Get
lalrl (TechnicalUser) 24 Nov 04 18:06 3) or let reactivate Trialphase by /// until you have decided, what to do. Then you get a new license-file and you have 30 days more time.
Reouting in BC.9thread806-950720Share This Forum Search FAQs Links Jobs Whitepapers MVPs
Check Out Our Whitepaper Library. Click Here.aau2 (TechnicalUser) 12 Nov 04 8:10 Hi, I have a System in BC.9 , and I want to reeoute an incoming call for the same route. The route configuration is :<rocap:rou=4;ROUTE CATEGORY DATAROU SEL TRM SERV NODG DIST DISL TRAF SIG BCAP4 412010011000 5 3101000007 0 30 128 03151515 011111000031 111111
END<rodap:rou=4;ROUTE DATAROU TYPE VARC VARI VARO FILTER 4 SL60 H'00000110 H'04C00000 H'060100A0 NO
END<roddp:dest=72086;EXTERNAL DESTINATION ROUTE DATADEST DRN ROU CHO CUST ADC TRC SRT NUMACK PRE72086 4 1005000000000250 5 6 0 72086902404704
END <
When is an internal call it´s works fine, but when is as incoming call for the same route it's don't work. Please help me
HIREI (TechnicalUser) 12 Nov 04 9:17 Hi,we have BC9 too. Some people said that to reroute the call to the same PRI EDSS1 route, the patch is needed. Between such routes the calls is rerouted OK.
patcher (TechnicalUser) 13 Nov 04 1:54 The description is not really clear. Do you mean incoming call will go out on the same route. Why don't you use ACD group without member.1. ACGRI:GRP=XXXX,.......;
Then check if you have spare abb.
2. ADCOI:ABB=XXXX,TRA=72086,CLASS=0&&3;3. CDINI:DIR=ACDGROUP,DIV=ABB;
The above setup is just sample for you to see and I am assuming this is what you need. The numbers I used are all sample and you can use your own numbering plan.
lalrl (TechnicalUser) 13 Nov 04 10:11
I´m not sure, but: MD in BC9 is normally rejecting direct rou-rou-traffic, if the rou is the same. If patchers solution does not work, try this: Devide your trunks in two different routes (same parameters) with overflow (cho=1) to each other. Then the Caller will leave the MD via the 2. route. This works.
HIREI (TechnicalUser) 13 Nov 04 15:21 lalrl, it's sounds reasonably. But in AXE-10 such things we do without any problem and without dividing to two routes. Quod licet Jovi, non licet bovi?Who can explain the philosophy?
Thanks.
patcher (TechnicalUser) 14 Nov 04 16:04 In order to make tromboning to work, the number in MD110 should be assigned as extensions,groups but not ABB or dest.
aau2 (TechnicalUser) 15 Nov 04 3:05 Hi hirei, what patch would I need?
HIREI (TechnicalUser) 15 Nov 04 4:20 Hi, aau2,I know the story but the patch number.
The story told one specialist in inet - as he was needed to reroute a call back to the same PRI EDSS1 interface and one kind man :) wrote the patch and debugged it, and the problem was solved. That's all, sorry.
fcpli (TechnicalUser) 16 Nov 04 4:33 The patch number is 67990
aau2 (TechnicalUser) 16 Nov 04 11:25 I don't have this patch for the unit slp60. The MD110 is for the spanish market. Where do I get the patch?
HIREI (TechnicalUser) 16 Nov 04 11:49 The standard answer says: you can get this patch from your local E/// support or from local authorised dilers (representatives) (www.ericsson.com).
patcher (TechnicalUser) 17 Nov 04 15:47 Why pursue on a patch since there is a work around for sure. Also BC9 has Red package(multi divert).
aau2 (TechnicalUser) 18 Nov 04 2:16 Patcher, I thought that the muldivert is for BC.10 or upper
patcher (TechnicalUser) 18 Nov 04 22:21 No, its not. Its in BC9 only...
parnum (TechnicalUser) 19 Nov 04 11:41 multidivert is a patch in bc 7 and 8 as well as bc9, also controlled by aspac. see if you can do aspap, if you can't you haven't got it (192 in bc9, 190 in bc8, 185 in bc7). but there are issues and they may only work on no reply, dont have any further info to hand at the moment to check. maybe someone can give a clearer answer rather than this pointer.
regards
TRIDENT100 (TechnicalUser) 19 Nov 04 12:25 Maybe you can use this:(from alex)- This parameter is only valid for sent A/connected number i.e., CNVTYP = 1. NUTRP:CNVTYP=1,NUMTYP=B,ENTRY=CCCC,TARDST=BBBB;RODDI:ROU=A,DST=BBBB,SRT=1;
see alex for more information
I have not testet this, but will do Monday
*/Trident*/
whosrdaddy (Vendor) 19 Nov 04 15:31 Trident,
this will only work from BC11, aau2's system is BC9... -------------------------------------- What You See Is What You Get
lalrl (TechnicalUser) 19 Nov 04 15:58 to patcher and parnum: Multidiversion exists up to BC11.
Avstral (TechnicalUser) 23 Nov 04 1:11
Well,Coming back to aau2 's question about BC9 and 67990.
This is rather simple correction and to be used as customer installation.
aau2, try this:
PCASI:UNIT=RMPS5,CI=C67990A,REV=1-R9A,IA=1DA6,RA=1DC4; END; !A; PCASI:UNIT=RMPS5,CI=C67990A,REV=1-R9A,IA=3206,RA=3224; END; !A; PCACS:UNIT=RMPS5,CI=C67990A;
Y; PCCOS:UNIT=RMPS5,CI=C67990A; Y;
Regards
aau2 (TechnicalUser) 24 Nov 04 3:06 Hi Avstral, thanks it works very fine, but I don't understand it. Why does it work if the patch is empty?Thanks for all
lalrl (TechnicalUser) 24 Nov 04 18:02 easy to explain: pcasi with IA and RA forces the unit, to jump directly from Hex-Value 1DA6 to 1DC4. All values between will be ignored. So the behaving of this unit will be changed.
Avstral (TechnicalUser) 24 Nov 04 19:33 aau2,
It is not empty. As lalrl noted, it cut out route checking for the tromboning case
Please, check up status of the trunks in your route for the next couple of weeks.You can get looped trunks without "disconnect" signal. Regards
aau2 (TechnicalUser) 9 Dec 04 10:56 And in BC.11 what can I do?. The unit RMPS5 don´t exist.The aspap 118 works?????.
Avstral (TechnicalUser) 9 Dec 04 23:10 Well, as soon as we still have RMP unit, for BC11 (SP13) you can use this:
PCASI:UNIT=RMP,CI=BC11TRO,REV=1-R18A,IA=2D850,RA=2D85C; END; !A; PCASI:UNIT=RMPS5,CI=BC11TRO,REV=1-R18A,IA=2F238,RA=2F244; END; !A; PCACS:UNIT=RMP,CI=BC11TRO; Y; PCCOS:UNIT=RMP,CI=BC11TRO; Y;
PARNUM 118 does not exist in BC11.It works in BC12.
But you can use more elegant solution without any corrections. Split the route you use on 2 routs (rou1 & rou2).Incoming calls comes via rou1.Outgoing calls use rou1 as main cho, rou2 as second cho.
Rerouted calls must use only dest for rou2.Thats all.
Regards
QUESTIONS ABOUT MD PERFORMANCEthread806-960149Share This Forum Search FAQs Links Jobs Whitepapers MVPs
Check Out Our Whitepaper Library. Click Here.cuneyt2919 (TechnicalUser) 1 Dec 04 3:03 We have CCM server 4.0 SP3 on MD110 BC10 versionWe have been monitoring approximately 450 agents and 50 ACD groups with this system..But after couple of days we will need no longer to monitor these amount of agents and ACD groups because of Genesys Contact center implementation. I mean CSTA data will be more important for us and CCM MIS data will have less importance for us.Related this issue, we have some questions:
1) Is it possible to disable some ACD groups, so that the PBX will generate and send MIS data for only some of ACD groups and agents. and will not generate and send for others.Even we remove the ACD groups from CCM Configuration Manager, will it be enough for MD110 not to generate MIS data for that ACD groups?
2) Does CTI and CCM datas make load on NIU cards? or another question is, if a same NIU card is being used for both CCM and CSTA data (CSTLI and ACFUI), will these datas effect the performance of NIU cards? Do you think that removing CCM link on that NIU card, will give us a better CSTA performance?Some times i see some errors on some CCM or CSTA links such as "ACD MIS faulty link" or "CSTA faulty channel" Can it be related with the load on NIU cards?
3)We have 24 lims and 24 NIU cards.And each NIU cards are configured on different lims.Thinking of the MD110 whole system, what will be optimum design for us to make MIS, CSTA and CIL data load sharing on whole MD system , so that MD can work with hi performance on high traffic?
4)We configured one of NIU card for CIL data.But we are afraid that this will be a bottle-neck for traffic handling of the whole MDsystem?Is it possible to configure the system , so that each lim will generate and send its own CIL data?(When we tried to configure a NIU card to send CSTA and CIL data at he same time, it gave an error message "resource not available")
doktor (IS/IT--Management) 1 Dec 04 12:58 Hi cuneyt2919
I have written my comments for your questions.Tomorrow I will add sone MML commands to these issues.
1)Yes, it will be possible to disable the MIS output to some ACD groups, so that the PBX will generate and send MIS data for only some of ACD groups and agents, and will not generate and send for others.MML command ACPAC...
2)Yes, CTI (App.link) and CCM data make (big) load on NIU cards,If the same NIU card is being used for both CCM and CSTA data (CSTLI and ACFUI), this (big) amount of data CAN (easily) effect the performance of NIU cards!!Removing CCM link on a NIU card, will give us a better CSTA performance. Yes! Of course!!The ALLOP; errors seen with CCM or CSTA links such as "ACD MIS faulty link" or "CSTA faulty
channel" , can easily be related with the load on NIU cards.HINT or RULE #1. Only use SEPARATE NIU boards for CSTA, as this often is connected to the customers call centre, where the customer earns his money.
3)Q:We have 24 lims and 24 NIU cards.And each NIU cards are configured on different lims.Thinking of the MD110 whole system, what will be optimum design for us to make MIS, CSTA and CIL data load sharing on whole MD system , so that MD can work with hi performance on high traffic?
A: Load sharing on CSTA should be done.Where the CSTA agents are placed (LIMs), NIU boards should be installed.The same with ACD MIS output.
4)Q:4)We configured one of NIU card for CIL data.But we are afraid that this will be a bottle-neck for traffic handling of the whole MDsystem?Is it possible to configure the system , so that each lim will generate and send its own CIL data?(When we tried to configure a NIU card to send CSTA and CIL data at he same time, it gave an error message "resource not available")
A:Load sharing on CIL could be done.CIL data can be spread out over some LIMs. NIU boards should be installed in e.g. 3 LIMs. One board for local calls, one for long distance calls and one for international calls.
Hope that you can use this!
Best regards doktor
doktor (IS/IT--Management) 2 Dec 04 10:43 Hi again
1)Concerning your Question 1):Yes, it will be possible to disable the MIS output toALL ACD groups, NOT single ACD groups.This setting is a system paramter.MML command ACPAC:ACDNUM=2,ACDVAL=0;To check current setting: ACPAP:ACDNUM=2;
Hope that you can use this!
Best regards doktor
cuneyt2020 (TechnicalUser) 6 Dec 04 2:22 Thanks doktor,This is helpful answer for me..regards..
route programming to predefined extensions???thread806-962544Share This Forum Search FAQs Links Jobs Whitepapers MVPs
Check Out Our Whitepaper Library. Click Here.wizo (TechnicalUser) 5 Dec 04 20:18 Hi guys, currently route 10 is outgoing analogue trunks, i have been requested incase of emergency to be able to make these as incoming lines as well ringing directly to predefined extensions so as incase of congestion on isdn indial emergency services can ring into critical areas of our hospital.
example
route 10 tru 001-1 to ring extn 2910route 10 tru 001-2 to ring extn 2911...route 10 tru 001-6 to ring extn 2250route 10 tru 001-7 to ring extn 2405
etc etc
ROEDP:ROU=10,TRU=ALL;ROUTE EQUIPMENT DATAROU TRU EQU SQU INDDAT CNTRL 10 001-1 001-1-71-00 10 001-2 001-1-71-01 10 001-3 001-1-71-02 10 001-4 001-1-71-03 10 001-5 001-1-71-04 10 001-6 001-1-71-05 10 001-7 001-1-71-06 10 001-8 001-1-71-07 10 001-9 001-1-72-00 10 001-10 001-1-72-01 10 001-11 001-1-72-02 10 001-12 001-1-72-03 10 001-13 001-1-72-04 10 001-14 001-1-72-05 10 001-15 001-1-72-06 10 001-16 001-1-72-07 10 002-1 002-1-72-00 10 002-2 002-1-72-01 10 002-3 002-1-72-02 10 002-4 002-1-72-03 10 002-5 002-1-72-04 10 002-6 002-1-72-05
10 002-7 002-1-72-06 10 002-8 002-1-72-07 10 002-9 002-2-71-00 10 002-10 002-2-71-01 10 002-11 002-2-71-02 10 002-12 002-2-71-03 10 002-13 002-2-71-04 10 002-14 002-2-71-05 10 002-15 002-2-71-06 END
hardian (TechnicalUser) 5 Dec 04 21:00
RODNI: ROU=10,TRU=1-1,DAY=2910,NIG=2910;RODNI: ROU=10,TRU=1-2,DAY=2911,NIG=2911; . . .RODNI: ROU=10,TRU=1-6,DAY=2250,NIG=2250;RODNI: ROU=10,TRU=1-7,DAY=2405,NIG=2405;
VOIP calls get disconnectedthread806-969941Share This Forum Search FAQs Links Jobs Whitepapers MVPs
Check Out Our Whitepaper Library. Click Here.Schaffsau (TechnicalUser) 17 Dec 04 7:29 Hello everybody,
Maybe you can help me with this Problem.I have an MD110 BC11 Servipack 12 when I got calls from Switzerland (Nortel Meridan) over two Cisco Gatways to the MD and hook of the call is disconnected.But when the call goes to the int. Voicemail it function. So maybe one of you have an Idee
regards Schaffsau
MDfreak (Vendor) 18 Dec 04 3:13 check the paramter PARNUM=253,in AS paramters
CAS extensionthread806-969296Share This Forum Search FAQs Links Jobs Whitepapers MVPs
Check Out Our Whitepaper Library. Click Here.EchoSpark (MIS) 16 Dec 04 10:08 Hi,
We have installed CAS TLU76/3 card on MD110 BC11 via RAD Vmux 2100 as a cas extension to Vmux 1100. The two VMux are connected via LAN.There are no alarms on both the MD110 and VMux but there is no dial tone on the extension.EXDDP:DIR=2800,EQU=6-1-00-01,TYPE=EL7,ICAT=0000;
where EQU is TLU 76/3 card.
Can someone help me?
wfhy (TechnicalUser) 17 Dec 04 0:37 Hi,What is vmux? is it a voice mail? If yes, please change ICAT=0006. I have done voice mail connected by CAS extension to MD110.
EchoSpark (MIS) 17 Dec 04 3:12 Vmux is a modular voice trunking gateway that compresses and transports up to 16 E1/T1 voice trunks over E1, T1 or IP links.
E&M connection..thread806-966623Share This Forum Search FAQs Links Jobs Whitepapers MVPs
Tek-Tips Forums is Member Supported. Click Here to donate.bolivar (IS/IT--Management) 12 Dec 04 8:31 Do anybody know how to connect MD110bc12.1 and BP250 R14 with an E&M..We are using TLU80 and BTU-E.What is the route parameters on MD site and BP site..Thank you very much for your help
MDfreak (Vendor) 14 Dec 04 4:37
MD side: connect the tie lines to TLU80 board, you should have the ground wire work properly in order to get this work OK.
route parameters:ROCAI:ROU=1,SEL=011000000000001,TRM=5,SERV=2110000000,TRAF=03151515,SIG=111000000000;RODAI:ROU=1,TYPE=TL22,VARC=032F0032,VARI=00012240,VARO=43011100;ROEQI:ROU=1,TRU=1-1&&1-4,EQU=1-0-30-0; /* for lines to equipment */RODDI:DEST=4,SRT=1,ROU=2; change the nessacry
BP side: in trunk parameters activite the command by the parameter:
command 5401 create a routecommand 1201 choose one of the following08 = Sweden, E&M signaling *) 09 = Continuous E&M signaling, A-format *)
10 = Continuous E&M signaling, D-format *) 11 = Discontinuous E&M signaling *) command 1302 ---> 0 = Decadic impulsing command 1023 ---> 2 = Trunk to a private exchange, tie line (TIE LINE)
in route paramters predigits should be the first digit of the MD number plane.
that's it and it should work ok
replacing PU4DCthread806-966403Share This Forum Search FAQs Links Jobs Whitepapers MVPs
Check Out Our Whitepaper Library. Click Here.abuokarem (TechnicalUser) 11 Dec 04 6:54 Hi all,
I have replaced in one site all PU4DC boards with the new RG5DC according to service advice regarding faulty PU4DC.After I replaced the PU4DC, every thing worked fine except the TLU44 in some magazines.TLU44 in some magazines get blocked and alarm code 260 takes place. The alarm code says that it’s a current feed problem (No current feed). What this mean and how to be solved??Did any one have faced such problem??The magazines were the TLU44 got blocked are LBP 14 & 15
Plz adviceThnx
abuokarem (TechnicalUser) 13 Dec 04 2:10 any ideas ??
lancbomb (TechnicalUser) 13 Dec 04 4:20 I have no "field experience" with this,
but to pre-empt, have you checked the voltages and all connections ?
abuokarem (TechnicalUser) 13 Dec 04 8:42 hi lancbomb, i have checked the voltages and the connections and every thing seems ok.i just want if any one know what is the meaning of the alarm : no current feed on the TLU44!!!!
thnx
lancbomb (TechnicalUser) 13 Dec 04 10:03 error code 260 is.........................
260 Fault on line to interworking PABX or public exchange see fault locating directions for FAULT CODE 260
ADD INFO 1: Individual pointer to TRS data individual ADD INFO 2: Description about the type of line fault for analogue external lines
1 = No current feed 2 = No proceed-to-send signals 3 = No seizure acknowledgement 4 = No clear acknowledgement from cooperating exchange has been received 5 = Lack of ringing signal at incoming seizure 6 = Received faulty decadic pulse from public exchange 7 = Time out occurred during digit reception 8 = Wrong pattern received 9 = Pulse out of range 10 = Faulty MFPI/MFPII signal detected or time out occurred during MFPI/MFPII signalling
lancbomb (TechnicalUser) 13 Dec 04 10:05 do an allop prinout,blfdp printoutroute prinoutand susip prinout
lancbomb (TechnicalUser) 13 Dec 04 10:06 also 260 says that
The alarm is generated in the following situations:
- The voltage on the line is not in accordance with the table values - No current in idle state is detected - No seizure acknowledgement has been received - A number of consecutive proceed-to-send signals have failed to appear - No clearing acknowledgement has been received
abuokarem (TechnicalUser) 14 Dec 04 2:30 ALLOP;ALARM LOGIDENTITY: ST-BC12-SP05 VERSION: CXP1010101/2/BC12SP5/R2A
260 FAULT ON LINE TO INTERWORKING PABX OR PUBLIC EXCHANGEDATE TIME ALP NOIF UNIT EQU BRDID INF1 INF2 ******* 02:12:18 2 7 TLP11 001-0-63-00 7 98 1
<blfDP;
FAULTY DEVICESEQU BOARDID BLOCKING DISTMARK LINELOCK 001-0-63-00 007 B'0000000000001000 NO NO
END
TRU<susip:rou=10,tru=all;STATUS INFORMATION AT 00:00:00 01JAN00ROU TRU TYPE TRAFFIC STATE/PTR LINE STATE/PTR ADD INFO10 001-1 TL11 IDLE #0062 BLOCKED #00F4END
<rodap:rou=10;ROUTE DATAROU TYPE VARC VARI VARO FILTER 10 TL11 H'00000101 H'00000108 H'000000D1 NO
END <rocap:ROU=10;ROUTE CATEGORY DATAROU SEL TRM SERV NODG DIST DISL TRAF SIG BCAP10 0110000010000010 4 3110000000 0 30 128 00151515 400000000000 001100
END
lancbomb (TechnicalUser) 14 Dec 04 9:45 thankxs
have you tried or can you try the folowing and post the results
1> block card/reseat card/restart card/unblock card
2> physically check that line is ok
3> swap the card/port for another in the system
4> see if the fault follows the card or the line.
I still find it hard to believe that the Powerd card has caused this.
MDfreak (Vendor) 29 Dec 04 13:55 which BC release do you have and do you have REU's still in MAG,s
nutri to destthread806-987415Share This Forum Search FAQs Links Jobs Whitepapers MVPs
Check Out Our Whitepaper Library. Click Here.
cuneyt2020 (TechnicalUser) 19 Jan 05 5:57 Hi, we want to set a number conversion to route, so that the converted number will be a dest and the customer will call outside by the help of this dest number. The problem is, when the number is converted to an extension , it works properly, but when the same number is converted to dest number it doesn't work?What should be the reason..Md version is bC12 SP6
Route parameter, destination parameter and nutrp which doesn't work, is like this,
<rodap:rou=68;ROUTE DATAROU TYPE VARC VARI VARO FILTER 68 SL60 H'00000300 H'00000000 H'04310000 NO
END <rocap:rou=68;ROUTE CATEGORY DATAROU SEL TRM SERV NODG DIST DISL TRAF SIG BCAP68 0110000000000010 4 2000030001 0 30 128 00151515 111110000031 001100
<roddp:DEST=all;EXTERNAL DESTINATION ROUTE DATADEST DRN ROU CHO CUST ADC TRC SRT NUMACK PRE0100 55 2005000000000250000000000 0 3 0 01021 98 1606100000000250006000000 0 1 0 7 1 2005000000000250000000000 0 3 0 7 2 2005000000000250000000000 0 3 0 01022 7 2005000000000250000000000 0 3 0 01023 92 1606100000000250006000000 0 1 0 7 1 2005000000000250000000000 0 3 0 7 2 2005000000000250000000000 0 3 0 01024 92 1606100000000250006000000 0 1 0 7 1 2005000000000250000000000 0 3 0 01025 7 2005000000000250000000000 0 3 0 01026 7 2005000000000250000000000 0 3 0 01027 7 2005000000000250000000000 0 3 0 01028 7 2005000000000250000000000 0 3 0
01029 7 2005000000000250000000000 0 3 0 01031 92 1606100000000250006000000 0 1 0 7 1 2005000000000250000000000 0 3 0 7 2 2005000000000250000000000 0 3 0 01032 7 2005000000000250000000000 0 3 0 01033 7 2005000000000250000000000 0 3 0 01034 7 2005000000000250000000000 0 3 0 01035 7 2005000000000250000000000 0 3 0 01036 7 2005000000000250000000000 0 3 0 01037 7 2005000000000250000000000 0 3 0 01038 7 2005000000000250000000000 0 3 0 01039 7 2005000000000250000000000 0 3 0 nutrp; (rou=68 is the related one)NUMBER CONVERSION DATAENTRY CNVTYP NUMTYP ROU TARDST PRE TRC NEWTYP CONT BCAP HLC0100 0 0 08 2 0 2242 0 0 0001 4 0 5446 0 0 5353 4 0 7000 0 0 8403 0 7900 0 0 0000 4 0 1021 0 0 68 01 4 0
when i make the nutri
nutri:ROU=68,ENTRY=1021,CNVTYP=0,NUMTYP=0,PRE=5621,TRC=4;
5621 is an extension, and the nutri works properly..
Any idea to advise me? I tried other numtypes and nothing changed...Rgrds
whosrdaddy (Vendor) 19 Jan 05 6:39
if I'm reading this correct you want forward acall coming from rou 68 towards public?
so 1021 incoming from rou 68 should take dest 01021?then nutri should be :
nutri:ROU=68,ENTRY=1021,CNVTYP=0,NUMTYP=0,PRE=0,TRC=0;
-------------------------------------- What You See Is What You Get
cuneyt2020 (TechnicalUser) 21 Jan 05 15:21 Hi whosrdaddy,
What i want to do is, when digits come from route 68 (i.e 1021 02164444444, i want to convert it to 01 02164444444) when digits come such as 1021 03124444444 , i want to convert it to 0103124444444so 1021 should be converted to 01
And i gave the command nutri:ROU=68,ENTRY=1021,CNVTYP=0,NUMTYP=0,PRE=01,TRC=4;
But when i try to convert it to a digits such as 01, which is a prefix for different routes,it is useless.When i test it, It gives tri-tone
if 1021 had been converted to a fixed extension (an ODN number for exp.) it should have been no problem. md accepts it and it dials the ODN
The dest.numbers 01021 01031 .. etc are working properly..No problem on dest number if no conversion had been done before.
Thanks for the reponse
whosrdaddy (Vendor) 22 Jan 05 6:06 ok now I understand your problem.
looking into your MD110 programmation, this should work.a few questions though, if you dial the dest manually (like 01031...), does it work??you can always do a call trace to understand what happens
/* setup trace, x = lim trunks from rou 68 stuni:unit=slp60,lim=x,msksig=02&03&A1,store=yes;/* set sizesttss:tri=1,size=500;/* start tracesttsi:tri=1;/* make call/* stop tracesttse:tri=1;/* print tracestrap:tri=1;
if you dont have a signal interpreter, paste trace results here, we will do it for you.these prints are also useful :
ROEDP:ROU=ALL,TRU=ALL;NADAP;
greetings,Daddy -------------------------------------- What You See Is What You Get
rfpui (TechnicalUser) 22 Jan 05 16:36 Hi to allWhosrdaddy is a magician But I have some questions for Daddy.
Q:1 ADC for route with DEST 01021 01031 are set as local private number (6 on position D2 and D4 in ADC) and nutrX ( X represent last letter ) NUMTYP is always is set as Unknown public number. Why and in my opinion it can be a problem.Q:2 I think that printout of command RONDP:ROU=68 is needed Q:3 the length of sending digits using roddXNUTRX cut 4 digits and add 2 digits
What You think about?
Sorry my English is no perfect
whosrdaddy (Vendor) 23 Jan 05 7:09 Q1 : you must specify numtyp for INCOMING call, it doesn't depend where you send the call to, but you're correct in asking this question, that's why I requested a call trace...Q2 : wrong, rondp is for outgoing calls, not for incoming callsQ3 : ?? what do you mean ??
cheers -------------------------------------- What You See Is What You Get
corch (TechnicalUser) 26 Jan 05 11:57 HiAre you sure that route support private TON ? Try with D19 in ADC set to "0"
cuneyt2020 (TechnicalUser) 26 Jan 05 12:46 Hi all, I checked the TLU trace and saw that it's not MD's fault...Last two digits were missing (our gateway's sending less digits. There is a limitation i think) I sent 1021 0256 4440333 via route 68 to md110 and saw on trace that the digits are 1021 025644403
When i made the conversion with 09, it worked properlySo no problem now...
thanks for your help
Rgrds.
part of trace18.31.03.960 -> Outgoing Call Reference: #094 Message: CALL PROCEEDING
18.31.04.620 -> Outgoing Call Reference: #094 Message: ALERTING Progress Indicator Coding Standard: CCITT standardized coding Location: Private network serving the local user Progress Description: In-band information is now available
18.31.06.280 <- Incoming Call Reference: #096 Message: SETUP Bearer Capability Coding Standard: CCITT Information transfer capability: 3.1 kHz audio Transfer mode: Circuit mode Information transfer rate: 64 kbit/s User information layer 1 protocol: CCITT G.711 A-Law B-Channel: 29 Progress Indicator Coding Standard: CCITT standardized coding Location: Private network serving the local user Progress Description: Origination address is non ISDN Calling Party Number Type of number: Unknown Numbering plan: Unknown Presentation indicator: Presentation restricted Screening indicator: User-provided, verified and passed Digits: 059992 Called Party Number Type of number: Unknown Numbering plan: ISDN/telephony numbering plan Digits: 1021025644403
Call Routingthread806-1003096Share This Forum Search FAQs Links Jobs Whitepapers MVPs
EchoSpark (MIS) 10 Feb 05 5:30 Hi,
I have MD110 with TLU-44 as trunk connected to PSTN. How do i program such that a call from external (PSTN) direct to the auto attendant and make a call using least cost routing table.
Thanks.
Isinor (Instructor) 10 Feb 05 8:40 To route a call to an Auto attendant...
RODNI:ROU=...,TRU=...,DAY=..,NIG=...;
To set up LCR for outgoing calls is a bit more complex, it requires a lot more info from you.
Such as your Existing LCR setup or ROU's, DEST's, Number plan, Access codes to service providers, what calls to what providers, etc.
RegardsIsinor
EchoSpark (MIS) 11 Feb 05 6:36 What i want is that an external caller should be able to get to auto attendant and dial 8(LCR code) to make another external call.Below is the data.
<LCDDP:TAB=FDT;LEAST COST DESTINATION DATAFICTITIOUS DESTINATION TABLEFRCT TZONE PRE 1 1 7500 6 1 7505 END<LCDDP:TAB=DNT2;LEAST COST DESTINATION DATANUMBER TABLEENTRY TRC PRE ACCT FRCT TOLL CBCS BTON TNS OSA8011 1 0 6 111111000000000 0 81 1 0 1 111111000000000 0 9009 1 0 2 000100001000000 0 END
NADAP;NUMBER ANALYSIS DATA TYPE OF SERIES NUMBER SERIES EXTERNAL DESTINATION CODE 7500 - 7509 75800 - 75999 770 - 776 778 - 779
LEAST COST ROUTING ACCESS CODE NUMBER SERIES 8 - 9EXTERNAL NUMBER LENGTH DATA EXTERNAL NUMBER NUMBER LENGTH7500 5 - 157505 7 - 19
<RODDP:DEST=7500&7505;EXTERNAL DESTINATION ROUTE DATADEST DRN ROU CHO CUST ADC TRC SRT NUMACK PRE7500 10 000500000001025000000000 0 5 0 20 1 000500000000025000000000 4 3 0 75009 21 2 000500000000025000000000 4 3 0 75009 7505 10 000500000001025000000000 0 5 0 20 1 000500000000025000000000 7 3 0 75009
21 2 000500000000025000000000 7 3 0 75009
<RODAP:ROU=10;ROUTE DATAROU TYPE VARC VARI VARO FILTER 10 SL60 H'00000310 H'15400000 H'06004010 NO
END <ROCAP:ROU=10;ROUTE CATEGORY DATAROU SEL TRM SERV NODG DIST DISL TRAF SIG BCAP10 711000000000001 7 3110000010 0 5 128 00151515 211110000031 111111
Thanks.
EchoSpark (MIS) 16 Feb 05 2:27 I know i can use DISA to achieve this, but is there any other way?
fcpli (TechnicalUser) 16 Feb 05 6:12 If I understand this correct, you want an incoming call(TLU44) to have a RVA message (or just dialtone), and then dial out (SLP60), no DISA? If this is the case, there is a patch for such a functionality (at least BC10, maybe other versions too).
EchoSpark (MIS) 18 Feb 05 2:09 Thanks fcpli, that is exactly what i want. I have BC11, what patch will i use.
fcpli (TechnicalUser) 18 Feb 05 5:45 Try 96737. Note that if using RVA, the MSG number has to be 3 and VARI in TLP11 xxxxxxx0!
SCEXI ?thread806-1019214Share This Forum Search FAQs Links Jobs Whitepapers MVPs
Find A Job or Post a Job Opening Click Here.mantra4all (TechnicalUser) 7 Mar 05 4:31 I have two MD110 with QSIG link between them.Both MD110 have only analog trunks to public switch.
What is the proper way to do SCEXI:
1) Both MD110 should receive sync from each other?or2) only one MD110 should have SCEXI, other is master exchange and does not receive sync?
lancbomb (TechnicalUser) 7 Mar 05 5:38 are they 2 stand alone lims ?
or LIM1 and LIM2 ?
cheers
whosrdaddy (Vendor) 7 Mar 05 6:47 lb : it's QSIG, so I suppose these are 2 separate systems.
mantra : In this case it is best to sync one system to another so case 2 is fine. -------------------------------------- What You See Is What You Get
himdp (TechnicalUser) 8 Mar 05 3:42 Mantra,case 1 is deffinitely NOT recommended. Ever seen a dog trying to catch its tail?
VBPCASI (TechnicalUser) 8 Mar 05 13:18 you can give SCEXI only on the slave LIM not on the master
mantra4all (TechnicalUser) 9 Mar 05 4:37 Hi people,
Thanks. Both MD are 1 LIM systems, exchange A is BC11, exchange B is BC12. I have done SCEXI only in exchange A, and it works OK.SCEXI:FEML=1-0-00-00; (QSIG equ, exchange A)
In the future I will have public ISDN for DID purposes in both MD110. I suppose that both MD110 should have SCEXI: SCEXI:FEML=R; ( to remove sync in exchange A)SCEXI:FEML=1-1-00-00; (public ISDN equ, exchange A) SCEXI:FEML=1-1-20-00; (public ISDN equ, exchange B)
Should I than put SCEXI:SEML=1-0-00-00; for spare clock in exchange A ?Is it mandatory to put public ISDN TLU76 in BPOS=1-0-00 ?
mundus (TechnicalUser) 9 Mar 05 10:41
Hi'Should I than put SCEXI:SEML=1-0-00-00; for spare clock in exchange A ?-you can do it as a spare but it's not a demand.
Is it mandatory to put public ISDN TLU76 in BPOS=1-0-00 ?- no.
Group hunting with external numbersthread806-1028886Share This Forum Search FAQs Links Jobs Whitepapers MVPs
Gezaba (TechnicalUser) 21 Mar 05 13:15 Has anyone an idea how to solve the following problem?
There is a group hunting group with internal and fixed remote extensions. This means, that they can receive local calls when the GH tries to give them a call. As the originating GH doesn't realizes, that the remote extension is busy, this member will be excluded from the group. The remote extension doesn't realizes, that it is excluded. After a while all remote members are excluded. SW is BC11.
lalrl (TechnicalUser) 21 Mar 05 14:21 Normally a gh-member will not be excluded from gh if MEX is busy. Only at "no answer" this can happen - depending on aspap:parnum=178. parval=1 will prevent this.
And you should make sure, that calls to and from the MEX will not bypass the MD.
And MEX should deactivate itself as answerposition via *21*own number# and reactivate with #21# to signal, that agent is not ready or ready.
Gezaba (TechnicalUser) 22 Mar 05 10:14 This is exactly what I tought. The problem arises in conjunction with calls bypassing the MD and going directly to the remote extensions. The exclusion happens at "no answer"....:(Is there any way to handle the situation when the remote extension receives a direct call, bypassing the MD? According to your opinion, can the PARNUM=178 PARVAL=0 help?(It is difficult to test it, because no remote access is allowed in this MD.)
lalrl (TechnicalUser) 22 Mar 05 17:06 I will test it tomorrow.
Connecting two different versions of MD110 remotelythread806-1026328Share This Forum Search FAQs Links Jobs Whitepapers MVPs
Check Out Our Whitepaper Library. Click Here.dnaserver (TechnicalUser) 16 Mar 05 20:35 Hi,
We have 2 different version of MD110 at different locations BC9 and BC11. The distance between them is about 300 KM. We have existing VPN leased line with 512kbps. We would like to connect both MD110 so that calls between them are free (VOIP). Is there any possiblity to connect them with different version of MD110? What is the exact router, cards and other item required ?
Thank You in advance.
whosrdaddy (Vendor) 17 Mar 05 4:09 you could do the trick with cisco 2610's (or equivalents) and connect them towards the MD110 with QSIG connection. this requires a TLU76 card in each MD110 (+ qsig licences for the BC11) -------------------------------------- What You See Is What You Get
Operator console.thread806-1032973
Share This Forum Search FAQs Links Jobs Whitepapers MVPs
Find A Job or Post a Job Opening Click Here.srad (Programmer) 28 Mar 05 19:41 Hi,
I have two Operator console, the problem is when phoning the principal console and this console is turned off (not night service),the result of call is "operator is absent". Why the call doesn't jump to the second operator console?How I can make it so that it jumps to the second console? How I can make it to put in night service the principal console?
Best regard.
whosrdaddy (Vendor) 29 Mar 05 1:03 need some printouts here :
opddp:dir=all;opcap:dir=all;opcgp:corg=all;opctp:corg=all;nadap:numtyp=oi&oc&od; -------------------------------------- What You See Is What You Get
pawshman (Programmer) 29 Mar 05 4:25 daddy is right,I would hazzord a guess that the OPCGP is not set upas an example (from memory)
55 00 00 12corg --1 112 123 01
In this example, there are 3 corg's or call orgin groups.1, 2 & 3 (this is how the calls come into the operators_
0 means no-calls handled1 firstb choice2 second choice
the opertors are 5001 and 5002
so corg (route 1) calls are handled evenly betweeen both operators.corg 2 (route 2) 5001 takes calls and as second choice 5002 then takes callsand corg 3 (route 3) only operator 5002 takes calls.
the word "route" doesnt refer to a route number, but as a generic term for incoming call, either internal or
external
HTH
PM
and 5002 will handle corg 1
srad (Programmer) 29 Mar 05 16:09 Hi,
This is the result of printouts:
<opddp:dir=all; OPERATOR DIRECTORY DATA
DIR EQU OCUST TYPE PCM REV 28500 001-0-22-00 - 5 1 R6A 38300 001-1-30-08 - 5 1 R6A
END
<opcap:dir=all; OPERATOR CATEGORY DATA
DIR OPC PRG TRAF TRM 28500 1000 3 1515 0 38300 1000 0 1515 0
END
<opcgp:corg=all; OPERATOR CALL ORIGIN GROUP DATA
DIR 23 88 53 00 00 CORG -- 1 12 2 11 3 11 4 11 5 11 6 11
END <opctp:corg=all; OPERATOR CALL TYPE DATA
CORG CALT ROU OACC CUST NDIR RERNUM CEN CCOP 1 7 2 28500 - N - N N
1 6 5 28500 - N - N N 2 1 - 9 - Y 38300 N N 3 2 - 9 - Y 38300 N N 4 3 - 9 - Y 38300 N N 5 5 1 - - Y 38300 N N 6 7 6 28500 - Y 38300 N N
END
<nadap:numtyp=oi&oc&od;NUMBER ANALYSIS DATA
TYPE OF SERIES NUMBER SERIES
OPERATOR INDIV. NUMBER SERIES 28500 38300
OPERATOR COMMON NUMBER SERIES 9
OPERATOR COM. DID. NUM. SERIES 28500
END
Thanks for all
Best regard.
whosrdaddy (Vendor) 29 Mar 05 16:52 I see what you mean,
you want to call 28500 and if it absent go to 38300 right?
a common mistake when programming ops is to give ops the DID number.
very simple solution : make all ops internal (like 101 and 102, people should never call these numbers) and make did numbers also common number -------------------------------------- What You See Is What You Get
Emergency Number - Functionalitythread806-1052329Share This Forum Search FAQs Links Jobs Whitepapers MVPs
akademik (TechnicalUser) 29 Apr 05 10:27 Hi Everyone
We have just upgraded to BC12 6.2.
We have an emergency phone SPEXI:DIR=3333,OPT=E;
Until the upgrade calls to the emergency phone were able to be transferred from the Voicemail system after certain options had been keyed. The progress of the call would be Recall - Dial 3333 - Wait for ring tone - Release. The call would then have been extended by the voicemail system to the emergency extension.
Now the same thing happens only the system doesn't allow a transferred call from an analogue line to the emergency extension. NU is encountered after Recall - Dial 3333, If we remove the SPEXI from the extension the call progresses normally.
We'd leave it like that if we didn't need other calls to conference onto the extension.
Reported it to the Service Provider they are looking in to it.
Consensus is that the facility isn't widely used. However, should anyone have found a solution to the issue we'd be grateful of any input.
Thanks - Paul
akademik (TechnicalUser) 29 Apr 05 15:13
Hi again - Just as I posted this the SP called back with the reason for the problem.
Are you ready for this?
The powers that be (Swedesville maybe) don't think that this should be a feature to allow an analogue extension to be able to hold a call and dial the emergency number. It shouldn't have worked in BC8 (although it did) and in BC10 it didn't and there was a patch created to overcome the issue. Only calls from analogue lines are affected in this way.
Reasons against providing the facility (The all knowing powers that be) In essence calling an emergency number automatically starts the conference bridge. This may conflict with the system which may believe that the extension calling in with a call on hold may want to start a conference.
In addition a call to an emergency line should only be made direct i.e. in an emergency situation such as the lift phone or fire call.
Reasons for providing the facility (in our opinion) In some cases the call may be forwarded by the voicemail system, where the caller has selected an option to direct his call to such a number, restricted extensions for example. Or the caller is already on a call and something which he may think he needs to report to the emergency number occurs, whether he puts the call on hold actively, or in haste and only effects a recall unaware that he has held his original call, receives dial tone and dials the emergency number.
We can see the logic however, if it worked in BC8 and there weren't any problems, maybe there were we don't know, what possessed them to take it away when they knew they had had to create a patch in BC10 to
provide the facility.
Fortunately we have been advised of two workarounds by the SP , a) to make the call over the PSTN then it doesn't know where the call is from, or b) to use a TLU card to fool the system into thinking the call is from another source. Thanks to the SP for being able to quickly re-create the scenario and provide a
solution.
If you have more to add on this your feedback is welcome.
Ciao - Paul
routine maintenancethread806-1111277Share This Forum Search FAQs Links Jobs Whitepapers MVPs
snakeblitsen (Programmer) 22 Aug 05 6:13 Hi, What routine maintenance should be done on an MD110 daily/weekly/monthly? backup etc. What about the batteries - on the Consono cabinet they are a bit inaccessible. Please advise - big interview comming up.cheers
MDatHome (Programmer) 23 Aug 05 4:18 This is my sugestion to you:- Backup should be done automaticly every day. (DUFQI)- Replace HDU every month. (have at least 3 HDUs to switch with) Store the "not in use" HDUs in a safe.- Do a check every day for alarms and history logs and clean them up after solving the problems. (If the history/alarm logs is too big the LIM(s) will restart).- 2 times/year do a powerfailure test. Run the system on batterys until it stops working. This is good for the batterys.
/MDatHome
How to: Divert calls to an external numberthread806-1110035Share This Forum Search FAQs Links Jobs Whitepapers MVPs
MrAds (IS/IT--Management) 18 Aug 05 12:11 I'm hoping this will be a straight forward question for someone to answer.
We have a number of fax machines that use 'Internal' lines connected to our PBX (Ericsson MD110 - very old), but we have recently inplimented a new ZetaFax server with multiple DDI's that can direct Faxes to email accounts.
In order not to have to tell every contact and customer we have ever dealt with that we are changing our Fax Numbers, I would like to be able to redirect these extentions to the direct BT telephone numbers associated with the ZetaFax server.
When I try this on our telephone system I can only divert calls to other internal extension numbers.
Is it possible to put an extention number on divert to an external number, and if so how?
cnhui (TechnicalUser) 19 Aug 05 3:08 YOU CAN CHANGE THE FAX EXTENSION NUMBER INTO GENERIC EXTENSION (GEDII), THEN WITH COMMAND GEPEI:DIR=XXXX,PROC=A22BXXXXXXXXB;YOU INITIALIZE THE DIVERSION PROCEDURE TOWARD THE EXTERNAL NUMBER. THE CDIV OF CSP OF THE GENERIC EXTENSION MUST BE SET APROPRIATERLY FOR THE EXTERNAL DIVERSION.
whosrdaddy (Vendor) 19 Aug 05 3:23 MrAds,
what is the version of your MD110?please provide the printout of the CADAP; command ----------------------------------------------------- What You See Is What You GetNever underestimate tha powah of tha google!
alchohaz (TechnicalUser) 19 Aug 05 9:56
There are plenty of ways to do this..
Turn the extensions into Common Abbreviated Dial numbers and then set the translation to the new DDI (useful as you can get stats on the amount of incming calls)
Allow external follow me on the Extensions (Change the Category).. and then key in from the handset *22*9xxxxxxxxx#Where 9 is the number for an outside line and xxx is the new external DDI. - this means you still have the fax to SEND faxes
Use Generic extension and Personal number, (BC10 and later revisions)
You could probably do something in NUTRI also, and i;m sure there are more solutions too... If you are on older software use of the first two listed
CheersAl Striker : My orders came through. My squadron ships out tomorrow, we're bombing the storage depots at Daiquiri at 18:00 hours. We're coming in from the North, below their radar.Elaine : When will you be back?Striker : I can't tell you that? It's classified.
Delster (TechnicalUser) 19 Aug 05 11:04 easiest solution is to remove the extension numbers in question from the ex number range (cease them first) and place in common abb dial range then program as abb dials. I've used that lots of times before and it works just fine.
NANSE:numtyp=ex,numse=(extension numbers);Nansi:numtyp=ac,numse=(extension numbers);Adcoi:abb=(extension number),tra=(zetafax number),class=0&&3;
just don't forget to add the 9 or whatever for an external line on the TRA
Del~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~umm,it IS supposed to do that, right??
IP NETWORKING WITH ELU32, BC12 SP2thread806-775902Share This Forum Search FAQs Links Jobs Whitepapers MVPs
Check Out Our Whitepaper Library. Click Here.TRIDENT100 (TechnicalUser) 14 Feb 04 8:47 Anybody have parameters for IP-trunk with ELU32?ROCAI:RODAI:ROEQI:RINII:RIANI:RODDI
whosrdaddy (Vendor) 16 Feb 04 4:34
Hi,
I use these parameters :
ROCAI:ROU=65,SEL=7110000000000010,SIG=111110100091,TRAF=03151515,SERV=3110000001,TRM=5,BCAP=001100;RODAI:ROU=65,TYPE=TL65,VARC=00000001,VARI=00000011,VARO=00000000; ROEQI:ROU=65,TRU=2-1&&2-8; /* make sure to use correct TRU ind depending on LIM number (where ELU32 is located)
RINII:BPOS=2-0-30,GRP=1,IP=10.12.17.12,MASK=255.255.255.0,ROUTER=10.12.17.1;RIANI:ROU=65,GRP=1,LROUid="local";
NANSI:NUMTYP=EN,NUMSE=95;SYIDI:EXGID=95;RONDI:EXNOPR=6-95,ROU=65;NANSI:NUMTYP=EC,NUMSE=90;RODDI:DEST=90,ROU=65,SRT=1,ADC=0626100000000050006000000,IP=10.12.17.16,rrouid="remote";http://www.damovo.com
corch (TechnicalUser) 30 Aug 04 7:14 HiPerhaps you can help me¿Which is the difference between IP in RIANP and IP in RODDI? Any of them can be used as a mask of getting connection to more than one board?If I want to use the same ELU32 for several routes, can I define several groups on it, or I must use only RODDI to choose where I would like to go?If I want to use several ELU32 for one route, I put all of them in the same group with RINII?Thanks
mundus (TechnicalUser) 30 Aug 04 14:20
Hi'¿Which is the difference between IP in RIANP and IP in RODDI? Any of them can be used as a mask of getting connection to more than one board?The IP adr. in RODDI has preference.If I want to use the same ELU32 for several routes, can I define several groups on it, or I must use only RODDI to choose where I would like to go?No, only one groups can be assign to one ELU 32 boards, but several route and RODDI to one groups. If I want to use several ELU32 for one route, I put all of them in the same group with RINII?Yes.
alchohaz (TechnicalUser) 23 Aug 05 12:06
Can anyone add anything to the above....
The ELU32 seems to allow for 8 trunks, does this mean that ONLY 8 seperate destinations can be applied to the card? So once a trunk is assigned to a route it cannot be used to go elswhere ??
i think i am missing a piece somewhere.. what is the best way to set up a MESH IP route network with the ELU32.
Lastly can some just put in plain English "RROUID" & "LROUID" which is the site at which where i am, and which is the distant end ??
CheersAl Striker : My orders came through. My squadron ships out tomorrow, we're bombing the storage depots at Daiquiri at 18:00 hours. We're coming in from the North, below their radar.Elaine : When will you be back?Striker : I can't tell you that? It's classified.
whosrdaddy (Vendor) 23 Aug 05 16:11 mundus,
if you have an IP trunking "network", I mean several sites with ELU32 in IP trunking mode, it is best to not set the IP address in the RAINI but in RODDI. concerning groups : you can have multipe ELU32's in one group but not multiple groups for 1 ELU32, use the method described above. It is best to have only one route per board.if you need more capacity just add more boards to the same group with rinii and increase the nr of trunks in the route.
alcohaz,the route can be reused for several destinations with different ip addresses.LROUID and RROUID are just name identifiers for a specific route. you don't have to use them but they are very usefull from a maintenaince point of view.ROUID's are case sensitive and are also used in the IP call setup. let me give you an example how to setup all of this :
suppose you have MD110 sites in london, bristol and glasgow, all sites have 1 ELU32 and all sites have WAN connections to each other.
suppose london has EN (exchange number) 910, bristol 911 and glasgow 912. ELU32 positions and IP addresses are not real offcourse.
london config :
NANSI:NUMTYP=EN,NUMSE=910;
NANSI:NUMTYP=EC,NUMSE=911&912;ROCAI:rou=65,xxxRODAI:ROU=65,xxxROEQI:ROU=65,TRU=1-1&&1-8;RIINI:BPOS=1-0-42,GRP=1,IP=10.10.10.100,MASK=255.255.255.0,ROUTER=10.10.10.1,ETHCNF=4;RAINI:ROU=65,LROUID="LONDON",GRP=1;/* bristol dest */RODDI:DEST=911,ADC=0626100000000050006000000,IP=10.10.11.100,SRT=1,RROUID="BRISTOL";/* glasgow dest */RODDI:DEST=912,ADC=0626100000000050006000000,IP=10.10.12.100,SRT=1,RROUID="GLASGOW";
bristol config :
NANSI:NUMTYP=EN,NUMSE=911;NANSI:NUMTYP=EC,NUMSE=910&912;ROCAI:rou=65,xxxRODAI:ROU=65,xxxROEQI:ROU=65,TRU=1-1&&1-8;RIINI:BPOS=1-0-42,GRP=1,IP=10.10.11.100,MASK=255.255.255.0,ROUTER=10.10.11.1,ETHCNF=4;RAINI:ROU=65,LROUID="BRISTOL",GRP=1;/* bristol dest */RODDI:DEST=910,ADC=0626100000000050006000000,IP=10.10.10.100,SRT=1,RROUID="LONDON";/* glasgow dest */RODDI:DEST=912,ADC=0626100000000050006000000,IP=10.10.12.100,SRT=1,RROUID="GLASGOW";
glasgow config :
NANSI:NUMTYP=EN,NUMSE=912;NANSI:NUMTYP=EC,NUMSE=910&911;ROCAI:rou=65,xxxRODAI:ROU=65,xxxROEQI:ROU=65,TRU=1-1&&1-8;RIINI:BPOS=1-0-42,GRP=1,IP=10.10.12.100,MASK=255.255.255.0,ROUTER=10.10.12.1,ETHCNF=4;RAINI:ROU=65,LROUID="BRISTOL",GRP=1;/* bristol dest */RODDI:DEST=910,ADC=0626100000000050006000000,IP=10.10.10.100,SRT=1,RROUID="LONDON";/* glasgow dest */RODDI:DEST=911,ADC=0626100000000050006000000,IP=10.10.11.100,SRT=1,RROUID="BRISTOL";
to make a correct printout for IP destinations, do RODDP:DEST=ALL (or X),IPOPT=YES;
here's a sample printout from my labo MD110 :
<RODDP:DEST=ALL,IPOPT=YES;EXTERNAL DESTINATION ROUTE DATADEST DRN ROU CHO CUST IP ADDRESS RROUID 95 65 10.10.17.16 peru 98 65 10.10.16.241 chili
Hope you can make sense of all this :))
Cheers,Daddy ----------------------------------------------------- What You See Is What You GetNever underestimate tha powah of tha google!
alchohaz (TechnicalUser) 24 Aug 05 11:57
This is very helpful.. thanks.. I will work through it and may have more questions to follow..
Such as - is there any means of pinging from the ELU32 interface?
alchohaz (TechnicalUser) 26 Aug 05 9:57 whosrdaddy
You have listed setting EN & EC in NADAP, i have not used these before, but seems straight forward.. Are they neccessary, will it work without that ??
whosrdaddy (Vendor) 26 Aug 05 11:41 EN = exchange numberEC = the same as ED but with coordinated number plan (give a difference in call logging output)
you can use ED if you want. ----------------------------------------------------- What You See Is What You GetNever underestimate tha powah of tha google!
alchohaz (TechnicalUser) 5 Sep 05 10:51
whosrdaddy - Gold star.. it now works after some major hassle with the Network... thanks for your valuable input.
CheersAl
Exclude extension diversion from Routethread806-1118314Share This
Forum Search FAQs Links Jobs Whitepapers MVPsFind A Job or Post a Job Opening Click Here.
tobsv (Programmer) 6 Sep 05 3:29 Hi,I have a route where I have an IVR connected. When someone call an extension the call is diverted on busy and no answer to the route. Perfect. If the IVR on this route calls a busy extension I would like it to be busy and not get diverted. The same goes for the no answer case. Is this possible? Route data:
/Tobias
<rocap:rou=3;ROUTE CATEGORY DATAROU SEL TRM SERV NODG DIST DISL TRAF SIG BCAP3 011010000000001 4 2010030000 0 30 128 00151515 111110000031 101100
END <roddp:DEST=999;EXTERNAL DESTINATION ROUTE DATADEST DRN ROU CHO CUST ADC TRC SRT NUMACK PRE999 3 060610000000008000600000 0 1 0
END <rodaP:ROU=3;ROUTE DATAROU TYPE VARC VARI VARO FILTER 3 SL60 H'00000310 H'15440000 H'06300000 NO
fouesnant (TechnicalUser) 6 Sep 05 6:41 Hi
If I understand well, phone A calls phone B diverted to an IVR connected via an ISDN route.Then if the IVR calls phone B, the diversion shall not take place, i.e. avoid loop on the ISDN route.Am I correct?
In any case, diversion of a phone is selected by D1 of CDIV parameter.Otherwise, you can play with D6D7D8D9 of CDIV parameter of the phone to allow or not diverstion depending of the origin of the call.Regarding loop avoidance on the same route, in BC12 you have ASPAC 118 that check the rerouting of a call coming on one route to go bak on the same route.
tobsv (Programmer) 6 Sep 05 9:24 Thanks for reply The scenario you describe is exactly correct. I have BC11 to ASPAC 118 is not available to me. For CDIV on the extension the only thing that change behavior is setting the D9 to 3. That stops diversion for the route but unfortunately that stops diversion for calls coming from our PSTN route also. I would still like incoming PSTN calls to get diverted to IVR route when the extension is busy/no answer.
To me it would seem like the PSTN calls should be affected by D8 (Origin is external public line) not D9 ( origin is private external line ). Can I change this on the PSTN route? That would probably solve my diversion problem to use different origins.
Current extension CDIV=011151113It seems like I must have CDINI on all extension for the diversion on busy/no answer to work.
regards Tobias
fouesnant (TechnicalUser) 6 Sep 05 12:50
Hi
Your problem can easly be solvedThe D3 bit in the SERV parameter of the route is made to differentiate Private line (your IVR) from Public line.For you IVR, you have set it to 1 which is correct.For you Public line you must set it to 0
tobsv (Programmer) 7 Sep 05 5:40 Absolutely perfect
Thank you very much
/Tobias
Problem with Trunksthread806-1110918Share This Forum Search FAQs Links Jobs Whitepapers MVPs
Check Out Our Whitepaper Library. Click Here.EchoSpark (MIS) 20 Aug 05 6:26 I have a route with trunks assigned as CO trunks but they get blocked intermittently.When i acknowledge alarms, the trunks get unblocked. I have included the Route parameters and the alarm log below. What can be done to rectify this?Please help me out.
<RODAP:ROU=9;ROUTE DATAROU TYPE VARC VARI VARO FILTER 9 TL11 H'00000002 H'00000008 H'00000015 NO
END <ROCAP:ROU=9;ROUTE CATEGORY DATAROU SEL TRM SERV NODG DIST DISL TRAF SIG BCAP9 0120000000000010 4 3100000000 0 30 128 00151515 400010000000 001100
<ALLOP;ALARM LOGRDATE RTIME 19AUG05 12:24:38 260 FAULT ON LINE TO INTERWORKING PABX OR PUBLIC EXCHANGEDATE TIME ALP NOIF UNIT EQU BRDID INF1 INF2 19AUG05 12:24:40 4 1 TLP11 001-1-50-00 7 96 1 RDATE RTIME 19AUG05 12:26:05 260 FAULT ON LINE TO INTERWORKING PABX OR PUBLIC EXCHANGEDATE TIME ALP NOIF UNIT EQU BRDID INF1 INF2
19AUG05 12:24:40 5 1 TLP11 001-1-50-01 7 95 1 RDATE RTIME 19AUG05 12:26:05 260 FAULT ON LINE TO INTERWORKING PABX OR PUBLIC EXCHANGEDATE TIME ALP NOIF UNIT EQU BRDID INF1 INF2 19AUG05 12:24:40 6 1 TLP11 001-1-50-02 7 94 1 RDATE RTIME 19AUG05 12:26:05 260 FAULT ON LINE TO INTERWORKING PABX OR PUBLIC EXCHANGEDATE TIME ALP NOIF UNIT EQU BRDID INF1 INF2 19AUG05 12:24:40 7 1 TLP11 001-1-50-03 7 93 1 RDATE RTIME 19AUG05 12:26:05
END
BLFDP;FAULTY DEVICESEQU BOARDID BLOCKING DISTMARK LINELOCK001-1-50-01 007 B'0000000000001000 NO NO 001-1-50-02 007 B'0000000000001000 NO NO 001-1-50-03 007 B'0000000000001000 NO NO001-1-50-00 007 B'0000000000001000 NO NOEND
VMPOP (Programmer) 22 Aug 05 4:22 Change those values
VARC=00000112,VARI=00000448,VARO=00000815;
may be it will help;East Or West Google Is The Best
EchoSpark (MIS) 24 Aug 05 13:59 Thanks VMPOP, i will try that and get back .
The voltage on the line is 75V...seems to be too high..can this be a problem?
NIUX (TechnicalUser) 27 Aug 05 3:19
Hi,
You have to keep your VARC=00000002 since your trunk board is TLU11 not TLU75.75V is too high and the MD110 may consider it as >RINGREC> signal, and it must be reduced.
BR///
EchoSpark (MIS) 31 Aug 05 2:52 Voltage is now okay but problem persists, noticed that the earth cable to the MD110 was disconnected.
Can this be a problem?
NIUX (TechnicalUser) 31 Aug 05 11:32
What happen if you tried to get the access code?Are the trunks blocked? print SUSIP:ROU=9,TRU=ALL;
The earth is a must, but sometimes it may work if the voltage difference between the PSTN and the MD is low.
One thing you can try to make sure it is not an earth problem, connect an analogue extension into one of the trunks (Loopback) and try to access it.
BR///
EchoSpark (MIS) 1 Sep 05 3:24 Thanks Niux,The trunks are blocked with blocking variable B4.
ROU TRU TYPE TRAFFIC STATE/PTR LINE STATE/PTR ADD INFO9 001-1 TL11 IDLE #0060 BLOCKED #00DF9 001-2 TL11 IDLE #005F BLOCKED #00DE9 001-3 TL11 IDLE #005E BLOCKED #00DD9 001-4 TL11 IDLE #005D BLOCKED #00DC9 001-5 TL11 IDLE #005C BLOCKED #00DB9 001-6 TL11 IDLE #005B BLOCKED #00DAEND
NIUX (TechnicalUser) 3 Sep 05 3:08
Have you tried connecting an analogue extension into one of the trunk lines?
BR///
EchoSpark (MIS) 15 Sep 05 3:30 Thanks a lot. It was discovered that the earthing on the power cable to the PBX was failing. The power cable has been changed and everything is working now.
Thanks for your help.
Procedure to program TLU79thread806-1128321Share This Forum Search FAQs Links Jobs Whitepapers MVPs
Check Out Our Whitepaper Library. Click Here.Chukwuemeka (TechnicalUser) 27 Sep 05 6:57 I need to programm ATEUS GSM Gateway BRI (TLU79)to MD110.
ROCAI:ROU=15,SEL=7110000000000010,TRM=5,SERV=3100000010,TRAF=00151515,SIG=111110000031,BCAP=101100;
RODAI:ROU=15,TYPE=SL60,VARC=00000204,VARI=05400000,VARO=46410000;
ROEQI:ROU=15,TRU=2-1&&2-4,EQU=2-1-60-01;
I programmed ROCAI, RODAI, but when I tried to do ROEQI, it said not accepted INIT. WRONG ORDER.
Can some one guide me on the correct procedure to go about, if possible, the correct parameters.
mundus (TechnicalUser) 27 Sep 05 8:07 Hi' try:ROEQI:ROU=15,TRU=2-1&&2-4,EQU=2-1-60-00;
singhbrindisi (TechnicalUser) 27 Sep 05 12:55 Hi,
ROCAI/RODAI/RODDI/ROEQI/RODNI ETC.
Cheers,""The truth about action must be known and the truth of inaction also must be known; even so the truth about prohibited action must be known. For mysterious are the ways of action""
Route between BC11 and BC12thread806-1111886
Share This
Forum Search FAQs Links Jobs Whitepapers MVPs
Find A Job or Post a Job Opening Click Here.
robsod (TechnicalUser) 23 Aug 05 5:33
We have recently upgrade a stand alone site to bc12 and moved the pbx, the other site is still bc11.After this was done i get many alarms with fault code 268,270,303 and 309. They come back every hour. I checked
CODERODAP:ROU=*IONCP;IONPP;
for that ROU and the parameters seem to be right on both sites.Any ideas of what could be wrong ? What could affect the trunk since the move. I can still dial the numbers over the trunk but the connection goes up and down for split second.
THX in advance.
robsod (TechnicalUser) 25 Aug 05 5:50
Any ideas ?
IPuser (TechnicalUser) 15 Sep 05 16:01
Could it be :-a) noisy line - or b) faulty card ?
To test a) Take the line out of service & try a BERT test.For b) Change the card(s)
whosrdaddy (Vendor) 15 Sep 05 17:53
check earthing on both sides.are you sure about the link, is there a provider involved??
----------------------------------------------------- What You See Is What You GetNever underestimate tha powah of tha google!
robsod (TechnicalUser) 19 Sep 05 8:11
I tried to change the TLU cards without any sucess...Yes there is provider involved with the link. But when i disconnect the slave side of the line is working perfectly.Whats a BERT test and how do i take the line out of service ? Earthing on both sides is OK.
whosrdaddy (Vendor) 19 Sep 05 12:05
seems to me this could be faulty cabling at one of the 2 sites or a provider problem...
----------------------------------------------------- What You See Is What You GetNever underestimate tha powah of tha google!
robsod (TechnicalUser) 20 Sep 05 2:05
I havent seen the cabling on the slave side myself, but how many ways is it possible to connect the cable ?
CLASS: 3thread806-1127122Share This Forum Search FAQs Links Jobs Whitepapers MVPs
Find A Job or Post a Job Opening Click Here.juanmiortiz (TechnicalUser) 23 Sep 05 11:57 hi,
I have the following message after ALLOP:
CLASS: 392 FAILURE TO SEIZE AN I/O PORT
can someone help me about what it means ??
Thanks in advance
rfpui (TechnicalUser) 23 Sep 05 12:46 from alex
The alarm will be generated if the I/O port, which should be used for spontaneous alarm printout or heart beat, could not be seized.
ADD INFO 1 Contains the number of the I/O port (first or second port). The first port printed in ALDIP is number one and the second port is number two.
----------------------------------If anything can go wrong, it will.(Murphy's Law)
acmi (TechnicalUser) 4 Oct 05 5:15 Automatic alarm output (ALDIP;) is turned on by ALAPI:IODEV=SYSTERMINAL,CLASS=X&&X; (or IO terminal from ALDIP;). To end ALAPE:IODEV=SYSTERMINAL;
Alarm output to modem dialing to a remote terminal is not very reliable. Alarm can also come up if local terminal collecting alarm data is off or disconnected from correct IO port.
See also ioifc & iofdc to set modem & IO port for output to remote terminal.
Setting up a new range of extension numberthread806-1133660Share This Forum Search FAQs Links Jobs Whitepapers MVPs
Tek-Tips Forums is Member Supported. Click Here to donate.major3838 (IS/IT--Management) 7 Oct 05 5:06 Hello All,
we tried to setting up a new range for extension numbers in MX-One (EMG).Within RDS configuration, PBX numbering series, we add a new range, and do the refresh database.
In EMG the new range is still not there.
Is there something more to do in order to reflect the new settings ( we don't want to use MML ) ?
NCCOI (IS/IT--Management) 7 Oct 05 6:26 As far as i know is there no way to assign a numbering serie with EMG without using MML in TTY.In my opinion is this unfortunately one of the restrictions of EMG.
major3838 (IS/IT--Management) 7 Oct 05 7:26 Thanks for your answer.
So if i 've to go with MML.....could you give me the command ?
whosrdaddy (Vendor) 7 Oct 05 7:29 Hi,
example for adding range 1000-1999NANSI:NUMSE=1000&&1999,NUMTYP=EX; ----------------------------------------------------- What You See Is What You GetNever underestimate tha powah of tha google!
whosrdaddy (Vendor) 7 Oct 05 7:30 don't forget to resync EMG (MD110 support) after this command ----------------------------------------------------- What You See Is What You GetNever underestimate tha powah of tha google!
major3838 (IS/IT--Management) 7 Oct 05 8:29 Many thanks for your Help.
The command is running fine.But i've this response :Number series already assigned !
Or in EMG, node "number series/voice extension" there is no such series.I've looked for in every node, and i did not find any trace of the series i try to create.
How to get revelant information about already assigned series numbers ?
Thanks,Philippe.
whosrdaddy (Vendor) 7 Oct 05 8:35 to see complete number plan :
NADAP; ----------------------------------------------------- What You See Is What You GetNever underestimate tha powah of tha google!
major3838 (IS/IT--Management) 10 Oct 05 4:21 Thank you for your Help.
I've already type this command but no trace of the new series number i try to setting up ......
whosrdaddy (Vendor) 10 Oct 05 4:51 post your NADAP here and the wanted number range... ----------------------------------------------------- What You See Is What You GetNever underestimate tha powah of tha google!
Need help deleting external numbersthread806-1139727Share This
Forum Search FAQs Links Jobs Whitepapers MVPs
Aythami (ISP) 20 Oct 05 7:33 Hello all I need to know how I can delete the external numbers 06 and 006 that is a NADAP; of my external numbers:
NUMBER ANALYSIS DATA
EXTERNAL NUMBER LENGTH DATA
EXTERNAL NUMBER NUMBER LENGTH
000 4 - 20001 4 - 4002 4 - 4003 4 - 4004 4 - 4005 4006 4 - 4007 7008 4 - 4009 4 - 4010 5 - 5011 4 - 6014 5 - 504 8 - 805 8 - 806 10 - 1007 8 - 808 10 - 1009 10 - 10
END
What I need to know is the command to delete it, thanks.
rfpui (TechnicalUser) 20 Oct 05 7:51
NANLR:EXL=06&006; ----------------------------------If anything can go wrong, it will.(Murphy's Law)
Operator console doesn't ringthread806-1147733Share This Forum Search FAQs Links Jobs Whitepapers MVPs
Tek-Tips Forums is Member Supported. Click Here to donate.cuneyt2020 (TechnicalUser) 7 Nov 05 4:02 Hi,
One of our customer upgraded their switch to BC12SP1.After upgrading they have a problem with their operator console. Sometimes the console doesn't ring, just shows calling number on display so they understand there is a new call.It's not a good situation for them. The product No. of the OPI console is " 1/DGF 220 01/4 R6A ".
Is there any idea what to do?
Rgrds.
slash50 (TechnicalUser) 7 Nov 05 5:11 Can you print out OPDDP:DIR=ALL; and OPCAP:DIR=ALL; and show the results here.
Do all the other functions on the OPS console work? Is there only 1 ops console? Does it even attempt to make a sound?
fcpli (TechnicalUser) 7 Nov 05 12:20 There is a correction for this. Ask your local /// vendor to deliver the patch. Or u can upgrade the switch to e.g. SP4 or higher. Maybe the latest (SP8) ????
whosrdaddy (Vendor) 7 Nov 05 14:16
a servicepack upgrade is really recommended here ----------------------------------------------------- What You See Is What You GetNever underestimate tha powah of tha google!
mundus (TechnicalUser) 7 Nov 05 16:19
I agree with whosdaddy - upgrade to sp 8 !
robsod (TechnicalUser) 8 Nov 05 2:56 Seen the same problem in BC11SP10 systems...Could someone explain whats wrong and how i fix it. When it happens OPTSP; says that the number is "Busy" and "Absent" like its a call stuck on it.Tried RFPUI:UNIT=DOM/DOR is that the best way to go around it ???Any more solutions ?
whosrdaddy (Vendor) 8 Nov 05 5:32 restarting OLP1T&DOR normally helps ----------------------------------------------------- What You See Is What You GetNever underestimate tha powah of tha google!
NCCOI (IS/IT--Management) 10 Nov 05 9:10 We have BC12SP6 and the same problem on several OWS's on different places and different times. So the problems seemed not related to one another. Is there a solution other than upgrading to SP8?
Thnx i.a.
PCLOP (TechnicalUser) 10 Nov 05 17:19 check TMU and UNIT=MPP.
erase OPI and init again OPI normally get new TMU channels
PCLOP
CAN'T INITIATE ANALOG EXTENSIONSthread806-1162266Share This Forum Search FAQs Links Jobs Whitepapers MVPs
mdtech (TechnicalUser) 7 Dec 05 21:05 I'm working on a BC11 systen that has never had analog extensions. I must be brain dead because I can't initiate analog extensions. The system gives me the following:<EXTEI:DIR=3220&&3235,TYPE=EL6,TRM=0,EQU=1-0-52-0,TRAF=00151501,SERV=000212070,CDIV=000071121,ROC=020001;WAITWAITWAITFAULT INTERRUPT
MESSAGE FROM OPERATING SYSTEM: RELOAD REQUESTEDRELOAD REQUESTED SYSTEM INITIATED DATA<HELP!!!!!!!!!!!
fouesnant (TechnicalUser) 8 Dec 05 3:01 Hi
May be some stupid question :What SP you have?Have you licenses for analogue extention?Is the board 1-0-52 an ELU29?Is the numbers 3220 to 3235 in extenions series? Have you tried to initiate only one extentions on the board?
I guess that you have data corruption on this number range.
slash50 (TechnicalUser) 8 Dec 05 3:09 Try restarting unit ELP6?
cfrei (TechnicalUser) 8 Dec 05 4:32 HIREI;EXTEI:DIR=XXXX,....HIMDP;
Try first this, then SFCEI;
slash50 (TechnicalUser) 8 Dec 05 5:11 To cfrei - Doing a HIREI will have no effect at all. That just clears the history log. SFCEI might do something, but I doubt it.
cfrei (TechnicalUser) 8 Dec 05 6:18 To slash50 - HIREI has no effect, but try HIMDP without previous HIREI. You got a lot of signals. If you first clear log, then send command and next read log, there were only some signals from program units.
I usually use SFCEI as first step, this command don't interrupt traffic in exchange. Next you can read HIMDP and restart units.
Very last possibility is RFEXI. This command is dangerous, interrupts ALL traffic.
pawshman (Programmer) 8 Dec 05 7:14 hi mdTECH,
i'D TRY THIS IN ORDER
1> if NO other extension on that card do 2> BLDBI:BPOS=xxxxxxxx;3> reseat card4> BLDBE:BPOS=xxxxxxx;5> CNBOE:BPOS=xxxxxxxx;6> CNHUI:LIM=1;
then try yout EXTEI, if still fails do following
1> HIREI2> do your EXTEI command3> if fails HIMDP (see what lost signals if need be print out here)4> restart/investigate the results
then try yout EXTEI, if still fails do following
1> SFCEI
any further holla back
rfpui (TechnicalUser) 8 Dec 05 7:35 mdtechIs the position 1-0-53 free? ----------------------------------If anything can go wrong, it will.(Murphy's Law)
mdtech (TechnicalUser) 8 Dec 05 13:24 Wow, thanks for all the great responses. This is actually a licensed lab system that I can restart at will. I've tried different NUMSE,BPOS and even different ELU29s. A more detailed fault report would be that once I CNBOI the board it shows up passive in CNLIP. I then EXTEI, as stated, and get no dial tone. When digitals call the exts they see "Vacant Number". I have a TMU/2 and RG5DC in the same LBP16 mag. Could they cause this problem?
rfpui (TechnicalUser) 8 Dec 05 15:02 Can You send to forum printout of commands:BLFDP:LIM=1;EXDDP:DIR=ALL;ECCAP:DIR=ALL;NADAP;CNLIP:DEV=YES;
Before sending printout read thread806-898504 please.----------------------------------If anything can go wrong, it will.(Murphy's Law)
Delster (TechnicalUser) 15 Dec 05 4:35 This may be a silly question but are there 16 free analogue ports available to you? also try setting up one extension and see what the response is to that.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~umm,it IS supposed to do that, right??
Replacement batteries for MD110thread806-1182931Share This Forum Search FAQs Links Jobs Whitepapers MVPs
Gosy (TechnicalUser) 27 Jan 06 3:53 We used to use Powersafe 6VJ11 cells but these are no longer made. We are now using Powersafe 12V62F but these do not fit at all well. Can you please advise me on an alternative for the 6VJ11. Thanks in advance.
slash50 (TechnicalUser) 27 Jan 06 4:14 Which type of power rack are they fitting into?
kank (IS/IT--Management) 27 Jan 06 8:29 Instead of using internal bateries we prepaired a home made cabinet (external) and put some big bataries which lasts longer. And put some extra fuses.
Gosy (TechnicalUser) 30 Jan 06 2:58 Our battery cabs have two rows of four Powersafe 6VJ11, can't remember the part number.
slash50 (TechnicalUser) 30 Jan 06 4:48 It is very easy to fabricate your own battery back-up. As long as you check the power ratings of the batteries and cable it correctly it will work with any battery.
Operator can't receive external callthread806-1204809Share This Forum Search FAQs Links Jobs Whitepapers MVPs
Find A Job or Post a Job Opening Click Here.david977 (TechnicalUser) 15 Mar 06 9:51 Hi All, I have one site (BC10) with the following problem:the operator can't receive external calls if it's assigned as answering position. for other answering positions like normal extensions and AA there is no problem. The queue counter in the operator display shows that there is call in queue. the caller receive silence for 5 seconds then disconnection tone. the trunk type is ISDN PRI. DID is disabled from PTT side. System data as following:
------------------------------------------------ <ROCAP:ROU=42;ROUTE CATEGORY DATAROU SEL TRM SERV NODG DIST DISL TRAF SIG BCAP42 011000001000001 4 3100000011 0 30 128 00151515 511110000030 101100
END
<RODAP:ROU=42;ROUTE DATAROU TYPE VARC VARI VARO FILTER 42 SL60 H'00000040 H'10020000 H'00010000 NO
END <RODDP:DEST=2;EXTERNAL DESTINATION ROUTE DATADEST DRN ROU CHO CUST ADC TRC SRT NUMACK PRE2 42 0005000000000250100 0 2 0
END <OPDDP:DIR=ALL; OPERATOR DIRECTORY DATA DIR EQU OCUST TYPE PCM REV 697 001-0-60-00 - 2 - - 698 001-0-60-01 - 2 - - 699 001-0-60-02 - 2 - -
END <OPCTP:CORG=1; OPERATOR CALL TYPE DATA CORG CALT ROU OACC CUST NDIR RERNUM CEN CCOP 1 5 42 - - N - N N 1 1 - 9 - N - N N 1 2 - 9 - N - N N 1 3 - 9 - N - N N
END <OPCGP:DIR=ALL; OPERATOR CALL ORIGIN GROUP DATA DIR 666 999 789 CORG --- 1 211
<CADAP;CALENDAR DATAIDENTITY=CROWN-PRINCE VERSION=LZY2035151/5/BC10CNA138/R4A16:05:23WED 15 MAR 2006END
---------------------------------------Please Advise
mundus (TechnicalUser) 15 Mar 06 11:28
If route 42 is a DID route ( which is normal ! ), then you recieved the B number digits from public eg. xxxx5678 or all digits 12345678.If you only recieved the last digit ( 5678 ) then you shall assign this in NA as NANSI:NUMTYP=ED,NUMSE=5678; remove OPCTR:CALT=5,ROU=42; and assign OPCTS:CORG=1,OACC=5678,CALT=7,ROU=42;If you recieved all digits ( 12345678 ) you shall also make NUTRI:ENTRY=1234,CNVTYP=0,NUMTYP=0,TRC=4,ROU=42,NUMTYP=0;Repeat this with NUMTYP=1, 2 and maybe also 3 and 4, this depend on what NUMTYP the public sent.
How do i initiate a TLU76 cardthread806-1210192Share This Forum Search FAQs Links Jobs Whitepapers MVPs
Check Out Our Whitepaper Library. Click Here.koobro (TechnicalUser) 28 Mar 06 4:16 How do i initiate a TLU76 card for ISDN PRI. I have BC12 SP9.
slash50 (TechnicalUser) 28 Mar 06 7:09
A lot depends on the settings your service provider are expecting, but here are some that should work...
Initiate the board: CNHUI:BPOS=x-x-xx-;
Initiate the route:ROCAI:ROU=X,SEL=7110000000000010,TRM=5,DIST=30,DISL=128,TRAF=00151515,SIG=111100000031,BCAP=001100;
RODAI:ROU=X,TYPE=SL60,VARC=00000300,VARI=00000000,VARO=00410000;
ROEQI:ROU=X,TRU=Z-1&&Z-15,EQU=X-X-XX-01;ROEQI:ROU=X,TRU=Z-16&&Z-30,EQU=X-X-XX-17;
Then assign a destination code to the route:RODDI:DEST=VV,ROU=X,ADC=0005000000000250000000000,TRC=0,SRT=2;
The important thing here is to set the start (SRT) point to send the digits to line after whatever digits you are using for a dest code. So if your dest code is 9 then SRT=2, if your dest code is 4920 then SRT=5.
Hope that makes sense....
koobro (TechnicalUser) 28 Mar 06 7:15 Slash50,
Thanks for the info.
Koobro
PCLOP (TechnicalUser) 28 Mar 06 8:30 very bad exampel Slash50. Your sig parameter required VPN licens.
slash50 (TechnicalUser) 28 Mar 06 9:10 What? The Net Services? It was only a quick example of initiating an ISDN route copying my parameters.
If you want to write out which sig, serv and sel parameters control what functions then you go ahead ;o)
Koobro - If you don't have the license for Network Services then set the last digit of sig to 0.
route to route connectivitythread806-1183251Share This Forum Search FAQs Links Jobs Whitepapers MVPs
Wachange (TechnicalUser) 27 Jan 06 13:00 I have VSATs connection to MD110 and I would like interconnect the two such that customers on route 1 can dial to the route 2 clients and communicate without passing the operator.
TeleLion (TechnicalUser) 27 Jan 06 19:11 If I understood you right, people will be calling external from route 1 into the MD and you want them to connect to another external number through route 2? If that is the tuition and if u have access to ALEX you can use the DISA function which allows an external caller to call an MD extension and from there you can dial and external number through that extension,,,,,,,,there are other ways of doing this,,,,,,let me know if you need another way.
Enjoy
Wachange (TechnicalUser) 28 Jan 06 2:00 TeleLion;Thanks, if I put in some details; I have two VSAT routes from different providers. The clients on route 1 would like to dial directly to clients on route 2. Route 2 is a global network interconnection of MD110 in so many countries while route 1 connects the clients within one country but are connected to MD110 via the VSAT. Send me more options that you be having.regardsWachange
VMPOP (Programmer) 13 Feb 06 5:29
you need a privite network router PNR , read about this in ALEX it's simple and could be done only via MD110 coomands
the PNR is the code for every PBX located in every countrey and it's used to dial using your VSAT routes, Question: are you connected via ISDN Qsig or another Tech.?because i have done this but via WAN instead of VSAT. East Or West Google Is The Best
kank (IS/IT--Management) 14 Feb 06 8:13 Define a common abrivation code(ABB) to get route 2. (ADCOI). Give command RORNI to reroute the call to this ABB. But important both can not be analog lines.
Wachange (TechnicalUser) 16 Feb 06 9:05 VMPOP;Thanks for your good answer. Actually, I would appreciate the configurations that you have done although
my setup is different.Route 1 on my PABX has a number scheme with 7 digits. A caller from a remote site dials the number directly then it is answered by operator.Route 2 on my PABX is 8 digit private network interconnecting different locations via the headquaters with DID facilities where you dial location code followed by the extension of the person you wish to speak to as: (XXXX+extension)The idea iam looking for is to allow remote clients on route 1 to call users directly in route 2 network just the same way an extension on the MD110 will dial to any extension within the network.
If you are in a postion to give an example of your configs, please, i will appreciate.
ThanksWachange
TeleLion (TechnicalUser) 17 Feb 06 13:05 What are your two routes ISDN, CAS, CCS, APNSS? or are they normal analogue trunks?
Wachange (TechnicalUser) 19 Feb 06 3:19 TelelionMy line are ordinary analogue telephone lines through the FXS card of the VSAT in door unit. I think for PNR to work I may need to change them to ISDN; what is your suggestion?
ThanksRgdWachange
Wachange (TechnicalUser) 19 Feb 06 6:52 Telelion;Mine are just ordinary trunks; I think it will be necessary to organize with service provider if such features has to be activated, What do you think about it...., please advice
Wachange
VMPOP (Programmer) 7 Mar 06 3:11 hey Telelioni advice you to use ISDN instead of analog to get the different Nodes you want.and i guess there's a way to do this using analog but i searched alot without any clue.
cheers East Or West Google Is The Best
Wachange (TechnicalUser) 17 Mar 06 5:52 VMPOP;It looks a great idea to PNR, is possible to share your configs as an example in this case. In other words can you share the cofigs.ThanksWachange
Wachange (TechnicalUser) 17 Mar 06 5:52 VMPOP;It looks a great idea to PNR, is possible to share your configs as an example in this case. In other words can you share the configs.ThanksWachange
VMPOP (Programmer) 19 Jun 06 6:50 PNR is used for routing of outgoing external private network calls i.e. calls terminating in the own private network. The function is the same as with basic routing, but PNR enables a lot more destinations to be
stated as entry to routing.
In addition to this, PNR enables each destination to have two route choices with enhanced number translation. One route choice can have a PRE of maximum 10 digits, and the other a PRE of maximum 16 digits. This is often sufficient for routing through the public network.
This means that the system is able to handle much bigger numbering plans by using PNR.
--------------------------------------------------------------------------------
PNR structure
PNR is basically a preprocessor to the existing basic routing software. The pre-process consists of two tables where the dialled number leads to a prefix, which in turn addresses a Route Choice Table (RCT). Basic routing uses the dialled number directly to address an RCT.
An RCT is all the route choices for a (fictitious) destination. Each route choice uses one destination data record. The route choices are initiated with the command RODDI .
The first PNR table is the PNR Destination Number Table (PR DNT). This is a table with 1500 entries where an entered destination (parameter ENTRY) will result in an index (parameter FRCT) to the next table, the fictitious RCT. Also the enhanced number translation data are stored in the PR DNT, two sets per destination.
The prefix stored in the fictitious RCT is used to address an RCT. The prefix is used by itself as a destination, it is not used for prefixing.
The purpose of the fictitious RCT is to restrict the addressing of the RCTs.
The purpose with restricting the addressing of the RCTs is that RCTs are taken from the common pool of 2500 destination data records that PNR shares with LCR and basic routing. An RCT may consist of up to 8 linked route choices, where each route choice uses one destination data record ( RODDI :DEST=,CHO=).
With PNR, one RCT may be used by many entries in the PR DNT. Because of this possibility of efficient utilization of the RCTs there should be enough destination data records for all (PNR, LCR and basic routing) if the PNR-configuration (and LCR-configuration) is well planned. This will be shown in the examples below.
The PNR data tables are administered by the command group LC and data is set, deleted or printed using the LCDDI /E/P commands where the parameter TAB is set to either PNR or RCT.
--------------------------------------------------------------------------------
Prerequisites Initiate the external destination number series using the command NANSI :
NANSI :NUMTYP=ED,NUMSE=85024; NANSI :NUMTYP=ED,NUMSE=85040; These external destination numbers will be used to address the PNR access code in the PR DNT.
If the market dependent parameter (MDP) NONADESTCHECK is set to Check is made, the prefix in the fictitious RCT must be initiated as an external destination number. This MDP states if the destination is to
be checked in the number analysis or not.
NANSI :NUMTYP=ED,NUMSE=0123; This external destination number is used by PNR to address an RCT. It is necessary to initiate it in the number analysis in order to be able to initiate it as a destination in the external analysis.
Initiate the external destination number series for PSTN access using the command NANSI :
NANSI :NUMTYP=ED,NUMSE=00; This external destination is required for overflow to the PSTN, when the dialled number is translated into a public number.
Outgoing routes must be assigned. In the following examples ROU=50 is a tie line route and ROU=20/30 are public external line routes.
--------------------------------------------------------------------------------
Execution Example 1, initiation of a tie line route
Initiate a route between the location Karlskrona (KA) and the locations Bollmora (BO) and Sundbyberg (SG). (HF is Huvudfabriken, a transit exchange near BO/SG.) The route in this example is a single tie line route.
Initiate the PNR access code for BO and SG. The same FRCT may be used for both BO and SG as they are both reached using the same route. Using the same FRCT means that they will share the same RCT. FRCT may be assigned any value between 1 and 64, X is used in this example.
LCDDI :TAB=PNR,ENTRY=85024,FRCT=X; LCDDI :TAB=PNR,ENTRY=85040,FRCT=X;
Result:
Table 7-1 PR DNT - PNR Destination Number Table ENTRY PRE TRC PRE TRC FRCT 85024 X 85040 X
Initiate the data in position X in the fictitious route choice table for PNR. The digits 0123 are used as prefix (external destination).
Note: RCT in the LCDDI command is only used as a parameter to distinguish this table from the other tables handled by the LCDDI command.
LCDDI :TAB=RCT,FRCT=X,PRE=0123;
--------------------------------------------------------------------------------
Result:
Initiate the RCT in the external analysis.
RODDI :DEST=0123,ROU=50,SRT=5; The SRT value depends on how the numbering plan in the network is set up. If the composed number is passing a transit exchange, the whole number may be sent, and the decision of the further routing is made in that same transit exchange.
Result:
Now the single tie line route between KA and BO/SG is initiated. If the user dials 85024 or 85040 followed by the extension number, the system will select route 50 for the completion of the call. The digits sent to the co-operating exchange will be either 24xxx or 40xxx.
--------------------------------------------------------------------------------
Example 2, initiation of an alternative route
Add a public alternative to the single tie line route between the location Karlskrona (KA) and the locations Bollmora (BO) and Sundbyberg (SG).
In this case the private numbers 85024 and 85040 will be translated individually.
The national public directory number for Bollmora is 08-682xxxx and for Sundbyberg 08-764xxx, where 08 is the area code and the following digits is the subscriber number (location code + directory number).
Add an alternative RCT. No editing information (PRE/TRC) is assigned with RODDI , instead a flag in the route choice indicates that this information will be found in the PNR destination table, under the PNR access code that was used to address the present RCT. The flag is: D 16 is set to 1 in the ADC parameter. The 1 also refers to set 1 in the PR DNT.
RODDI :DEST=0123,ROU=50,SRT=5; (initiated earlier) RODDI :DEST=0123,ROU=30,SRT=3,CHO=1,ADC=000000000000025100000;
--------------------------------------------------------------------------------
Result:
Update the PNR access code with the individual number translation information (set 1) for the BO and SG locations.
LCDDI :TAB=PNR,ENTRY=85024,FRCT=X,TRC=3,PRE=000868; LCDDI :TAB=PNR,ENTRY=85040,FRCT=X,TRC=3,PRE=000876;
Result:
PR DNT - PNR Destination Number Table ENTRY PRE TRC PRE TRC FRCT 85024 000868 3 X 85040 000876 3 X
Now the public choice is initiated. With alternative routing the route 30 is selected. The number translation information is found in the PR DNT (set 1) as indicated by D 16 in the ADC parameter.
If the user dials 85024/85040 followed by an extension directory number, and meet congestion at the ordinary choice, the system selects route 30 for completion of the call. The digits sent out to the co-operating exchange will be either 08682xxxx or 08764xxxx as indicated by set 1 of individual number translation information.
--------------------------------------------------------------------------------
Example 3, initiation of a second alternative route
Add a second alternative to the single tie line route between the location Karlskrona (KA) and the locations Bollmora (BO) and Sundbyberg (SG).
In this example a second set of individual number translation data is assigned to the private numbers 85024 and 85040. As there is no second network between KA and BO/SG in real life, the symbolic national PDN NNNNNN is used in this example.
--------------------------------------------------------------------------------
Add a second alternative RCT. No editing information (TRC/PRE) is assigned with RODDI , instead a flag in the route choice indicates that this information will be found in the PNR destination table, under the PNR access code that was used to address the present RCT. The flag is: D 16 is set to 2 in the ADC parameter. The 2 also refers to set 2 in the PR DNT.
RODDI :DEST=0123,ROU=50,SRT=5; (initiated earlier) RODDI :DEST=0123,ROU=30,SRT=3,CHO=1,ADC=xxxxxxxxxxxxx251xxxxx; (initiated earlier) RODDI :DEST=0123,ROU=20,SRT=3,CHO=2,ADC=xxxxxxxxxxxxx252xxxxx;
Result:
--------------------------------------------------------------------------------
Update the PNR access code with the individual number translation information (set 2) for the BO and SG locations.
LCDDI :TAB=PNR,ENTRY=85024,FRCT=X,TRC=3,PRE=000868,TRC1=N,PRE1=NNNNNN; LCDDI :TAB=PNR,ENTRY=85040,FRCT=X,TRC=3,PRE=000876,TRC1=N,PRE1=NNNNNN;
Result: PR DNT - PNR Destination Number Table ENTRY PRE TRC PRE TRC FRCT
85024 000868 3 N X 85040 000876 3 N X
Now the second choice is initiated. With alternative routing the route 20 is selected. The number translation information is found in the PR DNT (set 2) as indicated by D 16 in the ADC parameter.
If the user dials 85024/85040 followed by an extension directory number, and meet congestion at both the ordinary choice and the first alternative choice, the system selects route 20 for completion of the call. The digits sent out to the co-operating exchange will be either NNNNNNxxxx or NNNNNNxxxx as indicated by set 2 of individual number translation information.
Reverse polarity over analogue trunksthread806-1261758Share This Forum Search FAQs Links Jobs Whitepapers MVPs
Check Out Our Whitepaper Library. Click Here.trond456 (TechnicalUser) 2 Aug 06 8:29 I just asked the PTT for the reverse polarity service on the analogue trunks to avoid charging for the unanswered outgoing calls, parmeters below helped me to do this but the case now when make a call towards a site answered by Auto attendant the call disconnected,(calls not answered by auto attendant are successfully established)ROCAP:ROU=4;ROU SEL TRM SERV NODG DIST DISL TRAF SIG BCAP4 0110000001000010 4 3110000000 0 30 128 00151515 400110000000 001100
RODAP:ROU=ALL;ROUTE DATAROU TYPE VARC VARI VARO FILTER 4 TL11 H'0000A021 H'00000708 H'0000A015 NO
Is there any advice to modify the parameters above... and I will appreciate if there are parameters already tested with reverse polarity over analogue trunks...
mundus (TechnicalUser) 2 Aug 06 11:51 the reverse polarity service - EOS or B-answer ? If EOS then VARO d6 and SIG d4 is wrong and if B-answer then the VARO d7 is wrong but SIG d4 ok.
trond456 (TechnicalUser) 3 Aug 06 8:03 Thanks, I just tried the parametes below and this seems fine
ROCAI:ROU=1,SEL=0110000001000010,TRM=4,SERV=3110000000,SIG=500100020000,TRAF=00151515;
RODAI:ROU=1,TYPE=TL11,VARC=0000A021,VARI=00000708,VARO=0000A055;
Thanks you
Operator category thread806-1269108Share This Forum Search FAQs Links Jobs Whitepapers MVPs
niine (TechnicalUser) 21 Aug 06 7:11 hello!i have to block the calls from the operator to cellular phones, now the traf of the po is 1515, how can i do this?
Isinor (Instructor) 21 Aug 06 7:19 Hi,
The command is easy...
OPCAC:DIR=xxx,TRAF=xx15;
You need to know the CDCAT value to use in the xx bit, you can find this using...
NADAP:NUMTYP=CD; RegardsIsinor
niine (TechnicalUser) 21 Aug 06 7:57 Thank You Isinor, i'll try in this way
niine (TechnicalUser) 21 Aug 06 9:33 It works!Thank You Thank You Thank You
BC13thread806-1278783Share This Forum Search FAQs Links Jobs Whitepapers MVPs
rogers33 (TechnicalUser) 15 Sep 06 4:58 Hello,
We have just upgraded to BC13 and we have various sporadic glitches regarding various actions:
transfers not working,
pickups (i.e. not being able to pick up, as well as a delay in picking up the call. This is mainly on Analogue extensions.
trouble clearing lines on digital handsets (i.e. pressing buttons and nothing happens) and
screeching phones (mode D3),
phones being reported as busy when being dialled even though they aren't
If anyone has experienced these issues or any others on BC13 please let me know how they got fixed, or whether they are still an issue.
Cheers
fouesnant (TechnicalUser) 15 Sep 06 5:10 Hi
Are the involved extension using the parallel ringing feature?
rogers33 (TechnicalUser) 15 Sep 06 5:18 No we haven't programmed up this feature yet
fcpli (TechnicalUser) 15 Sep 06 14:17 About the screeching phones: This seems not to be just a BC13 (TSW) problem, it exists even in a BP. Just check the manufacturer and dateof manufacturing in the bottom of the D3 phone. A Fault report is made to // concering this matter, but at least I haven't seen any answer (yet). All other problems you describe here, are working normally. Did you convert the print data to BC13 with correct PC-REGEN?regardsfcpli
edex (TechnicalUser) 18 Sep 06 4:04 regards BC13/MX-ONE TSW where can I find the PC REGEN scripts. I only have upto BC12.1. Anyone help?
rogers33 (TechnicalUser) 18 Sep 06 4:27 You need the latest SP for Sam toolbox.
edex (TechnicalUser) 18 Sep 06 6:09 thanks for the info
LIDAP!!! Command Unkownthread806-1302914Share This Forum Search FAQs Links Jobs Whitepapers MVPs
admiralzino (IS/IT--Management)
17 Nov 06 4:53
i entered the command LIDAP and it is giving command unknown! does anyone know why?
thnx
AdmiralZino <LIDAP;COMMAND UNKNOWN<LIDAP;COMMAND UNKNOWN
doktor (IS/IT--Management) 17 Nov 06 5:02 What s/w version of MD110 do you have installed?LIDAP came with MD110 in BC10, so earlier versions such as BC 1 to BC 9 wil show COMMAND UNKNOWN.///doktor
admiralzino (IS/IT--Management) 17 Nov 06 5:21
VERSION=CXP1010101/2/BC12SP6/R3B
all the LI commands are returning with Command Unknown! which is strange cos these are commands i have been using until today.
<LIDAP;COMMAND UNKNOWN<LIDFP;COMMAND UNKNOWN<LIDAI;COMMAND UNKNOWN
whosrdaddy (Vendor) 17 Nov 06 5:27 rfpui:unit=lish,lim=1;
beware, this can cause a data reload , so check your backup first... ----------------------------------------------------- What You See Is What You GetNever underestimate tha powah of tha google!
admiralzino (IS/IT--Management) 23 Nov 06 5:20 thanks for the tip. LIDAP is now behaving normally.
rgds,Admiralzino
Can't remove call logthread806-1339380Share This Forum Search FAQs Links Jobs Whitepapers MVPs
NCCOI (IS/IT--Management) 27 Feb 07 2:37
Hi there,
See below:
<cldfp; FILE ADMINISTRATION DATAFILE STATEAAU ACT IODEV/PATH USER DEVICE STATE PRIORITY CALL-LOGGING CIL-1 READY/STARTED CFILE STATETTMS ACT IODEV/PATH USER DEVICE STATE PRIORITY
CALL-LOG-TTMS NONE READY/STARTED C CALL-LOG-TTMS2 NONE PASSIVE CEND <cldfe:iodev=call-log-ttms2,user=none;NOT ACCEPTEDFILE IS ACTIVE<
Although the cldfp says file is passive i can't remove call-log-ttms2 because cldfe says it's active.
What's the problem?
Thanx i.a.
whosrdaddy (Vendor) 27 Feb 07 7:07 use clode; and clohe; before cldfe; ----------------------------------------------------- What You See Is What You GetNever underestimate tha powah of tha google!
NCCOI (IS/IT--Management) 27 Feb 07 8:38 But what about the call-log-ttms in the same file ..?I have a call-log-ttms and a call-log-ttms2.This last one must be removed.
T.i.a.
whosrdaddy (Vendor) 27 Feb 07 9:37 look at CLINP;
you can give the file parameter with CLOHE; command ----------------------------------------------------- What You See Is What You GetNever underestimate tha powah of tha google!
NCCOI (IS/IT--Management) 27 Feb 07 10:08 That's it.
Thank you. I'm grateful.
Internal Follow methread806-1671987Share This Forum Search FAQs Links Jobs Whitepapers MVPs
Find A Job or Post a Job Opening Click Here.renke (TechnicalUser) 16 Jan 12 9:32 Hi there,
im pretty new with the MD 110 and there is a lot to learn ;)My first question is about the internal follow me.
there are some extensions that are able to configure other extension with the *21*number*target-number#. It don´t metter wich target number was configured befor.But now i have an cordless phone that is only allowed to configure the extension when the follow me is activeted with *21*cordless-phone-number# for the cordless phone.
Is this a configuration fault?
Kind regards
renke
lalrl (TechnicalUser) 17 Jan 12 4:32 there are two procedures:
1. *21*target#
This is a normal calldiversion for the case you know what the goal is.
2. *21*own number#
With this procedure you initiate "follow me". This means that you can go now to a any extension. There you can make procedure
*21*own number*number where you are#
If you go to the next extension, you can repeat the procedure. This is "follow me". All my calls follow me to the phone where I'm
renke (TechnicalUser) 17 Jan 12 5:20 hey lalrl,
thanks for your reply. I followed your instructions so i typed *21*259# (21*own-number#)on my phoneDisplay shows redirected to 259
so I went to my Cordless phone to actived the follow me.i´ve tried it with *21*259*459# (*21*own-number*number where i am#but i received an error, the display shows fault....
if i use another cordlessphone.. it works....
So how can i get my cordlessphone to do the same?
renke (TechnicalUser) 17 Jan 12 5:42 i think this is some kind of security-setting that allows the extension to do the follow me or not....?!
lalrl (TechnicalUser) 17 Jan 12 6:36 give the non working phone the same cat as the working phone (gedip, gedic)
DUMPING ISSUE
thread806-1663372Share This Forum Search FAQs Links Jobs Whitepapers MVPs
Check Out Our Whitepaper Library. Click Here.erickjper13 (TechnicalUser) 12 Oct 11 6:35 Guys,
I need your favorable help and your technical assistance about my case with "Dumping or DUSYI".
Thanks and best regards,
Here are some informations;
<DUSYI;SYSTEM DUMP INFORMATIONINCONSISTENT DATA DUE TO LAST RELOAD OF DATA WAS ERRONEOUS END
<ALLOP;ALARM LOGIDENTITY: ONSHORE-KJO VERSION: CXP1010104/2/BC12SP6/R3A
DATE: 12OCT11 TIME: 13:07:46CLASS: 342 RELOAD OF EXCHANGE DATA IN LIM HAS FAILEDDATE TIME ALP NOIF EQU INF1 INF2 INF3 12OCT11 13:06:41 1 1 001-*-**-** 132 1 128
42 RELOAD OF EXCHANGE DATA IN LIM HAS FAILEDDATE TIME ALP NOIF EQU INF1 INF2 INF3 12OCT11 13:06:41 2 1 002-*-**-** 132 1 128
42 RELOAD OF EXCHANGE DATA IN LIM HAS FAILEDDATE TIME ALP NOIF EQU INF1 INF2 INF3 12OCT11 13:06:41 3 1 003-*-**-** 132 1 128
42 RELOAD OF EXCHANGE DATA IN LIM HAS FAILEDDATE TIME ALP NOIF EQU INF1 INF2 INF3 12OCT11 13:06:41 4 1 004-*-**-** 132 1 128
42 RELOAD OF EXCHANGE DATA IN LIM HAS FAILEDDATE TIME ALP NOIF EQU INF1 INF2 INF3 12OCT11 13:06:41 5 1 005-*-**-** 132 1 128
42 RELOAD OF EXCHANGE DATA IN LIM HAS FAILEDDATE TIME ALP NOIF EQU INF1 INF2 INF3 12OCT11 13:06:42 6 1 006-*-**-** 132 1 128
42 RELOAD OF EXCHANGE DATA IN LIM HAS FAILEDDATE TIME ALP NOIF EQU INF1 INF2 INF3 12OCT11 13:06:42 7 1 007-*-**-** 132 1 128
42 RELOAD OF EXCHANGE DATA IN LIM HAS FAILEDDATE TIME ALP NOIF EQU INF1 INF2 INF3 12OCT11 13:06:42 8 1 008-*-**-** 132 1 128
42 RELOAD OF EXCHANGE DATA IN LIM HAS FAILEDDATE TIME ALP NOIF EQU INF1 INF2 INF3 12OCT11 13:06:42 9 1 009-*-**-** 132 1 128
42 RELOAD OF EXCHANGE DATA IN LIM HAS FAILEDDATE TIME ALP NOIF EQU INF1 INF2 INF3 12OCT11 13:06:42 10 1 010-*-**-** 132 1 128
42 RELOAD OF EXCHANGE DATA IN LIM HAS FAILEDDATE TIME ALP NOIF EQU INF1 INF2 INF3 12OCT11 13:06:42 11 1 011-*-**-** 132 1 128
42 RELOAD OF EXCHANGE DATA IN LIM HAS FAILEDDATE TIME ALP NOIF EQU INF1 INF2 INF3 12OCT11 13:06:42 12 1 012-*-**-** 132 1 128
42 RELOAD OF EXCHANGE DATA IN LIM HAS FAILEDDATE TIME ALP NOIF EQU INF1 INF2 INF3 12OCT11 13:06:42 13 1 013-*-**-** 132 1 128
42 RELOAD OF EXCHANGE DATA IN LIM HAS FAILEDDATE TIME ALP NOIF EQU INF1 INF2 INF3 12OCT11 13:06:42 14 1 014-*-**-** 132 1 128
42 RELOAD OF EXCHANGE DATA IN LIM HAS FAILEDDATE TIME ALP NOIF EQU INF1 INF2 INF3 12OCT11 13:06:42 15 1 015-*-**-** 132 1 128
42 RELOAD OF EXCHANGE DATA IN LIM HAS FAILEDDATE TIME ALP NOIF EQU INF1 INF2 INF3 12OCT11 13:06:43 16 1 016-*-**-** 132 1 128
42 RELOAD OF EXCHANGE DATA IN LIM HAS FAILEDDATE TIME ALP NOIF EQU INF1 INF2 INF3 12OCT11 13:06:43 17 1 017-*-**-** 132 1 128
<FISCP:IODEV=SYSDISK1; FILE SYSTEM CAPACITY DATATOTAL DISK SPACE: 488 MBYTESSUBFS: SYSSUBFS11KBYTES FILESTOTAL AVAIL TOTAL MOUNTED65536 65112 16000 /SYSN/USR1 SUBFS: SYSSUBFS21KBYTES FILESTOTAL AVAIL TOTAL MOUNTED65536 65124 16000 /SYSN/USR2
END <ALREI;
MESSAGE FROM OPERATING SYSTEM: RELOAD REQUESTED SYSTEM INITIATED DATAEXECUTED<HIREI;WAITEXECUTED<CADAP;CALENDAR DATAIDENTITY=ONSHORE-KJO VERSION=CXP1010104/2/BC12SP6/R3A13:06:54WED 12 OCT 2011END <IODDP;I/O DEVICE DATANODE IODEV/SUBFS BPOS/EQU I/O-BUS TYPE/USAGE STATUS AUTHSYSN - 001-0-22 - - IN SERVICE SYSN SYSDISK1 001-0-22-0 MASTER SanDisk IN SERVICE SYSSUBFS11 SYSSUBFS21SYSN SYSTERMINAL 001-0-22-1 - MML - 7SYSN MODEM 001-0-22-2 - MML - 7SYSN SPARE 001-0-22-3 - MML - 7SYSN NET1 001-0-22-4 - NETWORK/MML - 7OFFSHORE - 017-0-70 - - IN SERVICE OFFSHORE SYSTERMINAL1 017-0-70-1 - MML - 7OFFSHORE MODEM1 017-0-70-2 - MML - 7END <FIOFP:NODE=SYSN;NOT ACCEPTEDOPEN FILES NOT FOUND
erickjper13 (TechnicalUser) 16 Oct 11 2:07 Is there anybody who can help me about this problem.
Thanks,
parnum (TechnicalUser) 16 Oct 11 7:07
pls post DUBDP;
best parnum
erickjper13 (TechnicalUser) 16 Oct 11 23:57 Parnum,
here is the DUBDP printout;
DUBDP;
BACKUP DATAEXTERNAL BACKUP LATEST PREVIOUS REL1 REL2 NOT VALID NOT VALIDLOCAL BACKUP DIVERGENT TIME AND DATE LIM 1 08:50 28SEP11 09:35 26SEP11 2 08:50 28SEP11 09:35 26SEP11 3 08:50 28SEP11 09:35 26SEP11 4 08:50 28SEP11 09:35 26SEP11 5 08:50 28SEP11 09:35 26SEP11 6 08:50 28SEP11 09:35 26SEP11 7 08:50 28SEP11 09:35 26SEP11 8 08:50 28SEP11 09:35 26SEP11 9 08:50 28SEP11 09:35 26SEP11 10 08:50 28SEP11 09:35 26SEP11 11 08:50 28SEP11 09:35 26SEP11 12 08:50 28SEP11 09:35 26SEP11 13 08:50 28SEP11 09:35 26SEP11 14 08:50 28SEP11 09:35 26SEP11 15 08:50 28SEP11 09:35 26SEP11 16 08:50 28SEP11 09:35 26SEP11 17 08:50 28SEP11 09:35 26SEP11 END < MESSAGE FROM OPERATING SYSTEM: RELOAD REQUESTED SYSTEM INITIATED DATA
Thanks,
parnum (TechnicalUser) 17 Oct 11 8:43 First of all try
BLEQI:EQU=1-0-22-0;FIMOE:SUBFS=SYSSUBFS11;FIMOE:SUBFS=SYSSUBFS21;FIFTI:SUBFS=SYSsUBFS11;FIFTI:SUBFS=SYSSUBFS21;FIMOI:SUBFS=SYSSUBFS11;FIMOI:SUBFS=SYSSUBFS21;BLEQE:EQU=1-0-22-0,ALLFM=YES;RFBOI:BPOS=1-0-22;
log back on
RFPUI:UNIT=DRDH&DRDM,LIM=1;RFPUI:UNIT=NIP&FIP,LIM=1;
log back on
DUSYI;
best parnum
erickjper13 (TechnicalUser) 18 Oct 11 0:37 Parnum,
i have tried all of the above, unfortunately i got the same problem.
appreciate your kind assistance and support.
best regards,
<BLEQI:EQU=1-0-22-0;EXECUTED<FIMOE:SUBFS=SYSSUBFS11;EXECUTED <FIMOE:SUBFS=SYSSUBFS21;EXECUTED <FIFTI:SUBFS=SYSSUBFS11;FUNCTION TEST RESULTTEST OKEND <FIFTI:SUBFS=SYSSUBFS21;FUNCTION TEST RESULTTEST OKEND <FIMOI:SUBFS=SYSSUBFS11;EXECUTED <FIMOI:SUBFS=SYSSUBFS21;EXECUTED <BLEQE:EQU=1-0-22-0,ALLFM=YES;EXECUTED<RFBOI:BPOS=1-0-22;RFBOI:BPOS=1-0-22;SURE? (YES/NO)<Y;
AUTHORITY CLASS 7(C) COPYRIGHT ERICSSON ONSHORE-KJO 18OCT11 07:20:22 1-0-22-01 SYSTERMINAL
<RFPUI:UNIT=DRDH&DRDM,LIM=1;RFPUI:UNIT=DRDH&DRDM,LIM=1;SURE? (YES/NO)<Y;
RESTART PROGRAM UNITLIM STARTED PU:S FAILED PU:S
1 DRDH DRDM
EXECUTED
MESSAGE FROM OPERATING SYSTEM: RELOAD REQUESTED<RFPUI:UNIT=NIP&FIP,LIM=1;RFPUI:UNIT=NIP&FIP,LIM=1;SURE? (YES/NO)<Y;ORDERED <
SPONTANEOUS PRINTOUT MRESTART PROGRAM UNITJLIM STARTED PU:S FAILED PU:SJ 1 NIPM FIPMMENDMMLOGGED OFFè AUTHORITY CLASS 7(C) COPYRIGHT ERICSSON ONSHORE-KJO 18OCT11 07:22:24 1-0-22-01 SYSTERMINAL
<DUSYI;SYSTEM DUMP INFORMATIONINCONSISTENT DATA DUE TO LAST RELOAD OF DATA WAS ERRONEOUS END
Extension command lostthread806-1654690Share This Forum Search FAQs Links Jobs Whitepapers MVPs
Satellite1900 (TechnicalUser)
13 Jul 11 8:30
Hello guys,I have a problem on an extension. I know the number but I do not know what type it is, executing commands EXDDP, KSDDP, Sudip the answer is always "command lost".I would like to use the SGSAI command, but I do not know how to use it in my case.Do you have ideas?Greetings
batkotivalio (IS/IT--Management) 13 Jul 11 15:38 Try to restart the following program units:EHH, KHH, SUH by RFPUI command...
Satellite1900 (TechnicalUser) 14 Jul 11 2:33 the first thing I did, but it does not work
cfrei (TechnicalUser) 15 Jul 11 10:37 This units are not responsible for this problem. Only handlers. Try:HIREIEXDDP,(KSDDP),(SUDIP)HIMDP
In my very private opinion it can be problem in Number Analysis.
Satellite1900 (TechnicalUser) 15 Jul 11 12:53 Hi, the result of your request...
<HIREI;WAITEXECUTED<SUDIP:DIR=6847;DIRECTORY INFORMATION AT 18:41:39 15JUL11COMMAND LOST <EXDDP:DIR=6847;WAITWAITWAITCOMMAND LOST <KSDDP:DIR=6847;WAITCOMMAND LOST <HIMDP;
DIAGNOSTICS FROM OPERATING SYSTEMTIME DATE18:46:55 15JUL11NO INFORMATION STORED IN LIM 001NO INFORMATION STORED IN LIM 002NO INFORMATION STORED IN LIM 003NO INFORMATION STORED IN LIM 004NO INFORMATION STORED IN LIM 005NO INFORMATION STORED IN LIM 006NO INFORMATION STORED IN LIM 007NO INFORMATION STORED IN LIM 008NO INFORMATION STORED IN LIM 009NO INFORMATION STORED IN LIM 010NO INFORMATION STORED IN LIM 011NO INFORMATION STORED IN LIM 012NO INFORMATION STORED IN LIM 013NO INFORMATION STORED IN LIM 014NO INFORMATION STORED IN LIM 015NO INFORMATION STORED IN LIM 016NO INFORMATION STORED IN LIM 017NO INFORMATION STORED IN LIM 018
NO INFORMATION STORED IN LIM 019NO INFORMATION STORED IN LIM 020DIAGNOSTICS FROM LIM 021
TIME DATE ERROR CODE18:46:15 15JUL11 H'10EXECUTION TIMEOUTLOGICAL PROGRAM ERROR ADDRESS = 02041730ENTERSWSW B-LEVEL SIGNAL FETTCSNUME (H'0024)FROM KHH (H'1C2) EXE A IN LIM 001TO DER (H'17D) EXE A IN LIM 021NUMBER OF DATA BYTES IN SIGNAL = 10 WITH 0 1 2 3 4 5 6 7 8 9000 00 20 01 C2 01 06 08 04 07 0F
USER STACK DUMP 0 1 2 3 4 5 6 7 8 9 A B C D E F02 03 99 AA
TIME DATE ERROR CODE18:45:06 15JUL11 H'10EXECUTION TIMEOUTLOGICAL PROGRAM ERROR ADDRESS = 02041710ENTERSWSW B-LEVEL SIGNAL FETTCSNUME (H'0024)FROM EHH (H'199) EXE A IN LIM 001TO DER (H'17D) EXE A IN LIM 021NUMBER OF DATA BYTES IN SIGNAL = 10 WITH 0 1 2 3 4 5 6 7 8 9000 00 0E 01 99 01 06 08 04 07 0F
USER STACK DUMP 0 1 2 3 4 5 6 7 8 9 A B C D E F02 03 99 AA
TIME DATE ERROR CODE18:41:41 15JUL11 H'10EXECUTION TIMEOUTLOGICAL PROGRAM ERROR ADDRESS = 0204173EENTERSWSW B-LEVEL SIGNAL FETTCSNUME (H'0024)FROM SUH (H'334) EXE A IN LIM 001TO DER (H'17D) EXE A IN LIM 021NUMBER OF DATA BYTES IN SIGNAL = 10 WITH 0 1 2 3 4 5 6 7 8 9000 01 2B 03 34 01 06 08 04 07 0F
USER STACK DUMP 0 1 2 3 4 5 6 7 8 9 A B C D E F02 03 99 AANO INFORMATION STORED IN LIM 022NO INFORMATION STORED IN LIM 023NO INFORMATION STORED IN LIM 024NO INFORMATION STORED IN LIM 025
NO INFORMATION STORED IN LIM 026NO INFORMATION STORED IN LIM 027NO INFORMATION STORED IN LIM 028NO INFORMATION STORED IN LIM 029
END
Any idea?
himdp (TechnicalUser) 16 Jul 11 2:11 DER in LIM 21 is not responding to the request FETTCSNUME for exension number 6847. It is posible that a restart of DER in that LIM might fix this, but I am reluctant to restart DER in any single LIM as it can cause problems with freeseating linkages. It is also possible that there is data corruption in DER in that LIM which would need to be fixed with sacos or signals. Good luck.
cfrei (TechnicalUser) 16 Jul 11 7:30 What about tryEXTEI:DIR=6847,.....Probably it won't helps but better try everything before restart.
fcpli (TechnicalUser) 17 Jul 11 13:54 This is a corruption in DER. Which is your BC (CADAP) and DER version (CNPIP)?Then, I think that you have several "faulty" numbers in LIM 21.Print out EXCAP:DIR=ALL; and KSCAP:DIR=ALL; and check which is the first number failing (supposed to be in LIM 21).If so, print out SYEDP:LIM=21; In this case, no restart helps. If you have a dump with proper data, OK, but if not, this has to be solved step by step (or if you prefer, contact your SP).
Satellite1900 (TechnicalUser) 19 Jul 11 4:44 Hi fcpli,i don't have a dump with proper data, i'm sorry!The print of your reqestRegards<CNPIP:UNIT=DER;
PROGRAM UNIT INFORMATION PU-NAME PU-NO PRODUCT NUMBER REV PATCH DER H'17D 4/CAA 111 9572/011 R14A YES TYPE B'0000 0000 0000 0000 0100 0011 0000 0000 TYPEEXT B'0000 0000 0000 0000 0110 0000 0000 0011 LOADED IN LIM 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 END
<CADAP;CALENDAR DATAIDENTITY=Pluto VERSION=CXP1010015/5/BC11SP12/R2A10:34:52TUE 19 JUL 2011END
<EXDDP:DIR=ALL;EXTENSION DIRECTORY DATA DIR CUST EQU CAT TYPE ICAT AUX 1507 008-1-10-00 12 EL6 0000 1508 005-1-11-03 12 EL6 0000 1516 026-1-42-08 12 EL6 0000 1519 005-1-22-03 12 EL6 0000 15530 016-0-10-01 12 EL6 0000 15535 023-0-52-03 12 EL6 0000 15536 023-1-50-06 12 EL6 0000 15537 005-0-13-05 12 EL6 0000 .... many number..6790 026-0-42-08 37 EL6 0000 6791 026-0-42-09 37 EL6 0000 6794 001-1-20-04 14 EL6 0000 6797 7 028-3-52-07 2 EL6 0000 6804 012-0-21-02 16 EL6 0000 6806 7 014-0-12-04 56 EL6 0000 6815 7 028-3-52-08 2 EL6 0000 6818 7 028-3-52-09 2 EL6 0000 6827 007-1-50-05 27 EL6 0000 6829 7 028-3-52-10 2 EL6 0000 6835 004-0-20-05 2 EL6 0000 6839 009-1-10-03 16 EL6 0000 6841 7 011-1-10-03 17 EL6 0000 WAITWAITWAITCOMMAND LOST <KSDDP:DIR=ALL;KEY SYSTEM DIRECTORY DATADIR CUST EQU CAT ADN ODN CALALT 1429 57 22929 11430 57 6461 11521 2 4245 11522 2 4247 1 2 7247 1 7 6889 1...... MANY NUMBER....
.
.6603 7 3599 16605 020-1-50-00 2 6 2 26860 1 2 26861 1 2 26862 1 2 26863 16608 019-1-22-00 57 16612 018-1-10-01 7 16613 017-0-11-01 6 16614 011-1-61-04 7 1 2 6916 16619 020-1-40-06 16 16620 026-0-20-10 57 16625 013-1-61-03 6 16626 029-1-30-01 57 16643 7 4503 16646 008-1-52-00 7 16648 7 4513 16649 7 4590 16652 020-1-50-08 6 16669 029-2-32-05 7 16671 020-1-50-12 6 1 6 28767 16672 014-1-42-05 57 16675 029-1-30-06 7 16678 5 6009 16681 011-1-23-00 7 1 2 7288 16684 020-0-60-08 56 1 56 15971 1 5 27772 1 7 6122 16695 029-2-32-06 7 16700 26 5766 16702 012-1-42-03 7 1 2 5177 16703 020-0-60-02 7 16706 009-0-11-04 57 1 56 6302 1 2 6270 1 2 6823 16711 015-1-13-06 59 1 7 7094 0 7 8097 1 7 6945 16725 009-1-42-02 6 16726 028-2-62-15 6 16734 020-2-60-00 57 16736 010-1-60-04 56 16747 016-0-40-07 6 16762 7 011-1-23-04 17 16768 020-1-40-00 57 1 2 2200 1
6777 005-1-23-00 2 16778 020-1-30-00 56 1 7 8760 16783 013-0-50-05 6 16792 004-1-11-07 2 16793 020-1-30-02 57 16810 010-1-60-06 56 1 2 27784 1 6 3920 16813 029-2-22-00 57 16817 - 6105 16822 7 5741 26823 2 6706 16824 7 3215 16828 010-1-70-02 26 16830 008-1-71-02 7 16844 2 6582 16846 020-2-60-05 7 1COMMAND LOST <GEDIP:DIR=ALL;DIRECTORY NUMBER PROFILEDIR LIM CSP CUST LANG1200 20 10 - 41265 25 10 - 41266 25 10 - 41267 25 10 - 41270 25 10 - 41271 25 10 - 41420 25 10 - 41422 25 10 - 41427 25 6 - F1431 25 10 - 41432 25 10 - 41433 25 10 - 41434 25 10 - 41435 25 10 - 41436 25 10 - 41437 25 10 - 41438 25 10 - 41439 25 10 - 41440 25 10 - 41455 20 10 - 41456 26 10 - 41457 26 10 - 4... many number..8415 23 5 - 48416 28 5 - 48418 20 5 - 48420 22 6 - 48421 21 1 - 4
8422 23 6 - 48423 24 1 - 48424 20 1 - 48425 21 1 - 48426 20 4 - 48427 27 5 - 48428 27 6 - 48429 21 5 - 48430 20 5 - 48431 27 5 - 48433 1 5 - 48435 23 3 - 48436 20 5 - 48437 26 6 - 48440 20 6 - 48441 20 3 - 48442 26 5 - 48443 23 6 - 48444 23 5 - 48447 20 5 - 48448 22 5 - 48449 21 3 - 48450 22 10 - 48451 20 5 - 48453 26 4 - 48457 24 5 - 48458 21 3 - 48459 25 1 - 48460 21 5 1 48462 20 10 - 48463 22 10 - 48468 22 6 - 48469 23 6 - 48470 24 5 - 08471 27 1 - 48473 23 7 - 48475 22 6 - 48476 20 5 - 48480 21 1 - 48481 19 1 - 48482 22 3 - 48483 25 1 - 48485 23 6 - 48487 26 5 - 48488 23 10 - 48490 24 5 - 48491 20 10 - 48492 20 6 - 48494 22 10 - 48500 19 5 - 48509 23 10 - 48510 23 10 - 48511 23 6 - 48512 22 6 - 48513 20 5 - 4
8514 22 6 - 48517 20 6 - 48518 23 6 - 08519 23 6 - 48523 22 6 - 18555 26 6 - 48562 19 10 - 48566 20 5 - 48567 20 5 - 48588 20 5 - 48590 20 1 - 48609 24 1 - 48613 28 6 - 48614 22 10 - 48628 22 10 - 48632 25 4 - 48633 23 1 - 48635 1 1 - 48636 20 5 - 48640 21 10 - 48641 28 1 - 48645 22 10 - 48664 22 10 - 48671 28 6 - 48673 28 6 - 48674 23 6 - 48675 23 6 - 08676 22 6 - 08677 23 6 - 08681 22 10 - 48691 22 5 - 48693 28 1 - 48694 28 1 - 48698 28 5 - 48699 22 1 - 48700 20 5 - 48703 22 1 - 48705 20 1 - 48707 22 1 - 48711 22 6 - 48712 21 5 - 48717 23 5 - 48723 23 1 - 48730 22 1 - 48731 21 1 - 48737 23 1 - 48738 22 1 - 48748 19 6 - 48749 21 6 - 48750 21 6 - 48751 28 6 - 48759 23 6 - 48763 26 6 - 48768 23 1 - 48776 22 6 - 4
8781 27 10 - 48784 22 1 - 48793 20 10 - 48826 28 5 - 48835 22 1 - 48839 22 1 - 48852 21 1 - 48855 21 10 - F8857 23 1 - 48861 22 6 - 48864 20 5 - 48867 21 5 - 48880 9 0 - F8890 10 5 - 48895 25 1 - 48904 22 6 - 48905 22 6 - 48908 20 10 - 48909 23 10 - 48910 20 10 - 48912 20 10 - 48913 27 5 - 48917 23 1 - 48949 20 10 - 48979 18 10 - 48985 20 5 - 48986 21 5 - 4
END <ITDAP:DIR=ALL;ISDN EXTENSION DIRECTORY DATADIR EQU CUST SERV TRAF ADC CDIV ROC CAT ACCTYP 15532 026-0-20-00 - 020212010 00010102 00000001 000151000 000001 2 0-DUALWAITWAIT3184 020-1-50-05 - 021210000 00151515 00000001 000090000 000001 40 13349 019-2-40-01 - 021210000 00151515 00000001 000090000 000001 40 1-DUAL3350 019-2-40-01 - 021210000 00151515 00000001 000090000 000001 40 1WAITWAIT3782 019-2-40-02 - 021210000 00151515 00000001 000090000 000001 40 1-DUAL3783 019-2-40-02 - 021210000 00151515 00000001 000090000 000001 40 13812 020-1-50-05 - 020212010 00101003 00000001 001151000 000001 56 1-DUALWAITWAIT4439 021-0-30-07 - 021210000 00151515 00000001 000090000 000001 40 14447 021-0-30-07 - 020212010 00060603 00000001 001151000 000001 57 1-DUALWAITWAIT5454 013-0-50-00 - 021210000 00151515 00000001 000090000 000001 40 0-DUAL5455 013-0-50-00 - 021210000 00151515 00000001 000090000 000001 40 0WAIT5736 026-0-20-00 - 021210000 00151515 00000001 000090000 000001 40 0
WAITWAITWAITWAITCOMMAND LOST <SYEDP:LIM=21;SYSTEM EQUIPMENT DATAEQU BOARDID TYPE DIR ROU/TRU021-0-00-00 36 GJUL . .021-0-00-31 36 GJUL 021-0-10-00 102 AD . .021-0-10-31 102 AD 021-0-20-00 108 CTL 021-0-20-01 108 CTL 021-0-20-02 108 CTL 021-0-20-03 108 CTL 021-0-20-04 108 CTL 021-0-20-05 108 CTL 021-0-20-06 108 CTL 021-0-20-07 108 CTL 021-0-20-08 108 CTL 021-0-20-09 108 CTL 021-0-20-10 108 CTL 021-0-20-11 108 CTL 021-0-20-12 108 CTL 021-0-20-13 108 CTL 021-0-20-14 108 CTL 021-0-20-15 108 CTL 021-0-22-00 108 CTL 021-0-22-01 108 CTL 021-0-22-02 108 CTL 021-0-22-03 108 CTL 021-0-22-04 108 CTL 021-0-22-05 108 CTL 021-0-22-06 108 CTL 021-0-22-07 108 CTL 021-0-22-08 108 CTL 021-0-22-09 108 CTL 021-0-22-10 108 CTL 021-0-22-11 108 CTL 021-0-22-12 108 CTL 021-0-22-13 108 CTL 021-0-22-14 108 CTL 021-0-22-15 108 CTL 021-0-30-00 77 KL1 3853 021-0-30-01 77 KL1 6855 021-0-30-02 77 KL1 3886 021-0-30-03 77 KL1 7230 021-0-30-04 77 KL1 24614021-0-30-05 77 KL1 27149
021-0-30-06 77 KL1 27750021-0-30-07 77 KL1 4447 021-0-30-08 77 KL1 3129 021-0-30-09 77 KL1 4034 021-0-30-10 77 KL1 4571 021-0-30-11 77 KL1 36684021-0-30-12 77 KL1 4239 021-0-30-13 77 KL1 6856 021-0-30-14 77 KL1 5835 021-0-30-15 77 KL1 6857 021-0-30-23 77 KL1 4447 021-0-40-00 108 CTL 021-0-40-01 108 CTL 021-0-40-02 108 CTL 021-0-40-03 108 CTL 021-0-40-04 108 CTL 021-0-40-05 108 CTL 021-0-40-06 108 CTL 021-0-40-07 108 CTL 021-0-40-08 108 CTL 021-0-40-09 108 CTL 021-0-40-10 108 CTL 021-0-40-11 108 CTL 021-0-40-12 108 CTL 021-0-40-13 108 CTL 021-0-40-14 108 CTL 021-0-40-15 108 CTL 021-0-42-00 108 CTL 021-0-42-01 108 CTL 021-0-42-02 108 CTL 021-0-42-03 108 CTL 021-0-42-04 108 CTL 021-0-42-05 108 CTL 021-0-42-06 108 CTL 021-0-42-07 108 CTL 021-0-42-08 108 CTL 021-0-42-09 108 CTL 021-0-42-10 108 CTL 021-0-42-11 108 CTL 021-0-42-12 108 CTL 021-0-42-13 108 CTL 021-0-42-14 108 CTL 021-0-42-15 108 CTL 021-0-50-00 57 - 021-0-50-01 57 SL60 49/021-01021-0-50-02 57 SL60 49/021-02021-0-50-03 57 SL60 49/021-03021-0-50-04 57 SL60 49/021-04021-0-50-05 57 SL60 49/021-05021-0-50-06 57 SL60 49/021-06021-0-50-07 57 SL60 49/021-07021-0-50-08 57 SL60 49/021-08021-0-50-09 57 SL60 49/021-09021-0-50-10 57 SL60 49/021-10021-0-50-11 57 SL60 49/021-11
021-0-50-12 57 SL60 49/021-12021-0-50-13 57 SL60 49/021-13021-0-50-14 57 SL60 49/021-14021-0-50-15 57 SL60 49/021-15021-0-50-17 57 SL60 49/021-16021-0-50-18 57 SL60 49/021-17021-0-50-19 57 SL60 49/021-18021-0-50-20 57 SL60 49/021-19021-0-50-21 57 SL60 49/021-20021-0-50-22 57&
fcpli (TechnicalUser) 19 Jul 11 10:06 OK, the number is not in LIM21. Question: Is 6847 an existing number?If yes, let's see where it is located (if anywhere):sacop:uni´=ded,lim=1,sector=rel,addr=1b0d;Also, just for curiosity, trace DED when sending SUDIP:DIR=6847;:stisr;stuni:unit=ded,lim=1;sttsi:tri=1;SUDIP:DIR=6847;sttse:tri=1;create a log filestrap:tri=1;
fcpli
Satellite1900 (TechnicalUser) 19 Jul 11 13:13 Hi,Unfortunately, the 'extension does not exist.this is the result of trace:<STRAP:TRI=1;TRACE IND READ RESULTTRACE INDIVIDUAL NO 1TIME LINE(S)18.59.59.840 00001 SWSW SIGNAL GETDIRLIMNO (H'0045) FROM DER (H'017D) EXE A IN LIM 001 TO DED (H'017C) EXE A IN LIM 001 WITH 0 1 2 3 4 5 6 7 8 9 000 H'86 H'74 H'0F H'02 H'04 H'45 H'F6 H'02 H'03 H'78 010 H'C018.59.59.840 00002 SWSW SIGNAL *************** (H'0000) FROM DED (H'017C) EXE A IN LIM 001 TO DER (H'017D) EXE A IN LIM 001 WITH 0 1 2 3 4 5 6 7 8 9 000 H'15 H'02 H'00 H'0A H'9A H'00 H'00 H'00 H'0019.00.11.420 00003 SWSW SIGNAL FETDIRLIMNO (H'0023) FROM DER (H'017D) EXE A IN LIM 001 TO DED (H'017C) EXE A IN LIM 001 WITH 0 1 2 3 4 5 6 7 8 9 000 H'12 H'40 H'0F H'02 H'02 H'5B H'1A H'02 H'02 H'B0 010 H'D019.00.11.420 00004 SWSW SIGNAL *************** (H'0000) FROM DED (H'017C) EXE A IN LIM 001 TO DER (H'017D) EXE A IN LIM 001 WITH 0 1 2 3 4 5 6 7 8 9 000 H'19 H'02 H'00 H'02 H'7E H'00 H'00 H'00 H'00
19.00.17.480 00005 SWSW SIGNAL FETDIRLIMNO (H'0023) FROM DER (H'017D) EXE A IN LIM 001 TO DED (H'017C) EXE A IN LIM 001 WITH 0 1 2 3 4 5 6 7 8 9 000 H'88 H'15 H'0F H'02 H'02 H'5B H'1A H'02 H'02 H'B0 010 H'D019.00.17.480 00006 SWSW SIGNAL *************** (H'0000) FROM DED (H'017C) EXE A IN LIM 001 TO DER (H'017D) EXE A IN LIM 001 WITH 0 1 2 3 4 5 6 7 8 9 000 H'FF H'02 H'00 H'02 H'7E H'00 H'00 H'00 H'0019.00.20.120 00007 SWSW SIGNAL FETDIRLIMNO (H'0023) FROM DER (H'017D) EXE A IN LIM 001 TO DED (H'017C) EXE A IN LIM 001 WITH 0 1 2 3 4 5 6 7 8 9 000 H'58 H'01 H'0F H'02 H'02 H'5B H'1A H'02 H'02 H'B0 010 H'D019.00.20.120 00008 SWSW SIGNAL *************** (H'0000) FROM DED (H'017C) EXE A IN LIM 001 TO DER (H'017D) EXE A IN LIM 001 WITH 0 1 2 3 4 5 6 7 8 9 000 H'17 H'02 H'00 H'02 H'7E H'00 H'00 H'00 H'0019.00.20.920 00009 SWSW SIGNAL FETDIRLIMNO (H'0023) FROM DER (H'017D) EXE A IN LIM 001 TO DED (H'017C) EXE A IN LIM 001 WITH 0 1 2 3 4 5 6 7 8 9 000 H'58 H'01 H'0F H'02 H'02 H'5B H'1A H'02 H'02 H'B0 010 H'D019.00.20.920 00010 SWSW SIGNAL *************** (H'0000) FROM DED (H'017C) EXE A IN LIM 001 TO DER (H'017D) EXE A IN LIM 001 WITH 0 1 2 3 4 5 6 7 8 9 000 H'17 H'02 H'00 H'02 H'7E H'00 H'00 H'00 H'0019.00.23.160 00011 SWSW SIGNAL FETDIRLIMNO (H'0023) FROM DER (H'017D) EXE A IN LIM 001 TO DED (H'017C) EXE A IN LIM 001 WITH 0 1 2 3 4 5 6 7 8 9 000 H'58 H'01 H'0F H'02 H'02 H'5B H'1A H'02 H'02 H'B0 010 H'D019.00.23.180 00012 SWSW SIGNAL *************** (H'0000) FROM DED (H'017C) EXE A IN LIM 001 TO DER (H'017D) EXE A IN LIM 001 WITH 0 1 2 3 4 5 6 7 8 9 000 H'17 H'02 H'00 H'02 H'7E H'00 H'00 H'00 H'0019.00.23.320 00013 SWSW SIGNAL FETDIRLIMNO (H'0023) FROM DER (H'017D) EXE A IN LIM 001 TO DED (H'017C) EXE A IN LIM 001 WITH 0 1 2 3 4 5 6 7 8 9 000 H'58 H'01 H'0F H'02 H'02 H'5B H'1A H'02 H'02 H'B0 010 H'D019.00.23.320 00014 SWSW SIGNAL *************** (H'0000) FROM DED (H'017C) EXE A IN LIM 001 TO DER (H'017D) EXE A IN LIM 001 WITH 0 1 2 3 4 5 6 7 8 9 000 H'17 H'02 H'00 H'02 H'7E H'00 H'00 H'00 H'00
19.00.24.720 00015 SWSW SIGNAL FETDIRLIMNO (H'0023) FROM DER (H'017D) EXE A IN LIM 001 TO DED (H'017C) EXE A IN LIM 001 WITH 0 1 2 3 4 5 6 7 8 9 000 H'08 H'58 H'0F H'02 H'02 H'5B H'1A H'02 H'02 H'B0 010 H'D019.00.24.720 00016 SWSW SIGNAL *************** (H'0000) FROM DED (H'017C) EXE A IN LIM 001 TO DER (H'017D) EXE A IN LIM 001 WITH 0 1 2 3 4 5 6 7 8 9 000 H'15 H'02 H'00 H'02 H'7E H'00 H'00 H'00 H'0019.00.24.860 00017 SWSW SIGNAL FETDIRLIMNO (H'0023) FROM DER (H'017D) EXE A IN LIM 001 TO DED (H'017C) EXE A IN LIM 001 WITH 0 1 2 3 4 5 6 7 8 9 000 H'58 H'01 H'0F H'02 H'02 H'5B H'1A H'02 H'02 H'B0 010 H'D019.00.24.860 00018 SWSW SIGNAL *************** (H'0000) FROM DED (H'017C) EXE A IN LIM 001 TO DER (H'017D) EXE A IN LIM 001 WITH 0 1 2 3 4 5 6 7 8 9 000 H'17 H'02 H'00 H'02 H'7E H'00 H'00 H'00 H'0019.01.29.120 00019 SWSW SIGNAL FETDIRLIMNO (H'0023) FROM DER (H'017D) EXE A IN LIM 001 TO DED (H'017C) EXE A IN LIM 001 WITH 0 1 2 3 4 5 6 7 8 9 000 H'62 H'82 H'0F H'02 H'02 H'5B H'1A H'02 H'02 H'B0 010 H'D019.01.29.120 00020 SWSW SIGNAL *************** (H'0000) FROM DED (H'017C) EXE A IN LIM 001 TO DER (H'017D) EXE A IN LIM 001 WITH 0 1 2 3 4 5 6 7 8 9 000 H'17 H'02 H'00 H'02 H'7E H'00 H'00 H'00 H'0019.01.44.520 00021 SWSW SIGNAL FETDIRLIMNO (H'0023) FROM DER (H'017D) EXE A IN LIM 001 TO DED (H'017C) EXE A IN LIM 001 WITH 0 1 2 3 4 5 6 7 8 9 000 H'93 H'01 H'0F H'02 H'02 H'5B H'1A H'02 H'02 H'B0 010 H'D019.01.44.520 00022 SWSW SIGNAL *************** (H'0000) FROM DED (H'017C) EXE A IN LIM 001 TO DER (H'017D) EXE A IN LIM 001 WITH 0 1 2 3 4 5 6 7 8 9 000 H'15 H'02 H'00 H'02 H'7E H'00 H'00 H'00 H'0019.02.14.920 00023 SWSW SIGNAL FETDIRLIMNO (H'0023) FROM DER (H'017D) EXE A IN LIM 001 TO DED (H'017C) EXE A IN LIM 001 WITH 0 1 2 3 4 5 6 7 8 9 000 H'58 H'01 H'0F H'02 H'02 H'5B H'1A H'02 H'02 H'B0 010 H'D019.02.14.920 00024 SWSW SIGNAL *************** (H'0000) FROM DED (H'017C) EXE A IN LIM 001 TO DER (H'017D) EXE A IN LIM 001 WITH 0 1 2 3 4 5 6 7 8 9 000 H'17 H'02 H'00 H'02 H'7E H'00 H'00 H'00 H'00
19.02.18.120 00025 SWSW SIGNAL FETDIRLIMNO (H'0023) FROM DER (H'017D) EXE A IN LIM 001 TO DED (H'017C) EXE A IN LIM 001 WITH 0 1 2 3 4 5 6 7 8 9 000 H'58 H'01 H'0F H'02 H'02 H'5B H'1A H'02 H'02 H'B0 010 H'D019.02.18.120 00026 SWSW SIGNAL *************** (H'0000) FROM DED (H'017C) EXE A IN LIM 001 TO DER (H'017D) EXE A IN LIM 001 WITH 0 1 2 3 4 5 6 7 8 9 000 H'17 H'02 H'00 H'02 H'7E H'00 H'00 H'00 H'0019.02.18.300 00027 SWSW SIGNAL FETDIRLIMNO (H'0023) FROM DER (H'017D) EXE A IN LIM 001 TO DED (H'017C) EXE A IN LIM 001 WITH 0 1 2 3 4 5 6 7 8 9 000 H'58 H'01 H'0F H'02 H'02 H'5B H'1A H'02 H'02 H'B0 010 H'D019.02.18.300 00028 SWSW SIGNAL *************** (H'0000) FROM DED (H'017C) EXE A IN LIM 001 TO DER (H'017D) EXE A IN LIM 001 WITH 0 1 2 3 4 5 6 7 8 9 000 H'17 H'02 H'00 H'02 H'7E H'00 H'00 H'00 H'0019.02.37.820 00029 SWSW SIGNAL FETDIRLIMNO (H'0023) FROM DER (H'017D) EXE A IN LIM 001 TO DED (H'017C) EXE A IN LIM 001 WITH 0 1 2 3 4 5 6 7 8 9 000 H'62 H'82 H'0F H'02 H'02 H'5B H'1A H'02 H'02 H'B0 010 H'D019.02.37.820 00030 SWSW SIGNAL *************** (H'0000) FROM DED (H'017C) EXE A IN LIM 001 TO DER (H'017D) EXE A IN LIM 001 WITH 0 1 2 3 4 5 6 7 8 9 000 H'17 H'02 H'00 H'02 H'7E H'00 H'00 H'00 H'0019.03.01.520 00031 SWSW SIGNAL FETDIRLIMNO (H'0023) FROM DER (H'017D) EXE A IN LIM 001 TO DED (H'017C) EXE A IN LIM 001 WITH 0 1 2 3 4 5 6 7 8 9 000 H'27 H'71 H'0F H'02 H'02 H'5B H'1A H'02 H'02 H'B0 010 H'D019.03.01.520 00032 SWSW SIGNAL *************** (H'0000) FROM DED (H'017C) EXE A IN LIM 001 TO DER (H'017D) EXE A IN LIM 001 WITH 0 1 2 3 4 5 6 7 8 9 000 H'17 H'02 H'00 H'02 H'7E H'00 H'00 H'00 H'0019.03.14.180 00033 SWSW SIGNAL FETDIRLIMNO (H'0023) FROM DER (H'017D) EXE A IN LIM 001 TO DED (H'017C) EXE A IN LIM 001 WITH 0 1 2 3 4 5 6 7 8 9 000 H'58 H'01 H'0F H'02 H'02 H'5B H'1A H'02 H'02 H'B0 010 H'D019.03.14.180 00034 SWSW SIGNAL *************** (H'0000) FROM DED (H'017C) EXE A IN LIM 001 TO DER (H'017D) EXE A IN LIM 001 WITH 0 1 2 3 4 5 6 7 8 9 000 H'17 H'02 H'00 H'02 H'7E H'00 H'00 H'00 H'00
19.03.14.820 00035 SWSW SIGNAL FETDIRLIMNO (H'0023) FROM DER (H'017D) EXE A IN LIM 001 TO DED (H'017C) EXE A IN LIM 001 WITH 0 1 2 3 4 5 6 7 8 9 000 H'72 H'23 H'09 H'02 H'02 H'5B H'1A H'02 H'02 H'B0 010 H'D019.03.14.820 00036 SWSW SIGNAL *************** (H'0000) FROM DED (H'017C) EXE A IN LIM 001 TO DER (H'017D) EXE A IN LIM 001 WITH 0 1 2 3 4 5 6 7 8 9 000 H'1A H'02 H'00 H'02 H'7E H'00 H'00 H'00 H'0019.03.17.020 00037 SWSW SIGNAL FETDIRLIMNO (H'0023) FROM DER (H'017D) EXE A IN LIM 001 TO DED (H'017C) EXE A IN LIM 001 WITH 0 1 2 3 4 5 6 7 8 9 000 H'58 H'01 H'0F H'02 H'02 H'5B H'1A H'02 H'02 H'B0 010 H'D019.03.17.020 00038 SWSW SIGNAL *************** (H'0000) FROM DED (H'017C) EXE A IN LIM 001 TO DER (H'017D) EXE A IN LIM 001 WITH 0 1 2 3 4 5 6 7 8 9 000 H'17 H'02 H'00 H'02 H'7E H'00 H'00 H'00 H'0019.03.17.180 00039 SWSW SIGNAL FETDIRLIMNO (H'0023) FROM DER (H'017D) EXE A IN LIM 001 TO DED (H'017C) EXE A IN LIM 001 WITH 0 1 2 3 4 5 6 7 8 9 000 H'58 H'01 H'0F H'02 H'02 H'5B H'1A H'02 H'02 H'B0 010 H'D019.03.17.180 00040 SWSW SIGNAL *************** (H'0000) FROM DED (H'017C) EXE A IN LIM 001 TO DER (H'017D) EXE A IN LIM 001 WITH 0 1 2 3 4 5 6 7 8 9 000 H'17 H'02 H'00 H'02 H'7E H'00 H'00 H'00 H'00END Thanks
fcpli (TechnicalUser) 20 Jul 11 4:36 OK, seems that DED has old information of the number. So, we have to remove it. For this, I need to see the sacop mentioned before, this just to be sure that we are on the right track...
fcpli
Satellite1900 (TechnicalUser) 22 Jul 11 1:26 Hi,tihis is the print
sacop:uniT=ded,lim=1,sector=rel,addr=1b0d; MEMORY CONTENT ON ADDRESS POSITION EXE A
ADDRESS 0 1 2 3 4 5 6 7 8 9 A B C D E F ISO 00001B00 FF 04 15 FF FF 09 FF 0B FF FF 0A FF 14 15 FF FF ................END
Best regards
fcpli (TechnicalUser) 22 Jul 11 8:16 OK,
sacos:uniT=ded,lim=1,sector=rel,addr=1b0d,data=ff;
This sacosneeds to be entered in all other LIMs, too. But before this, check that the command is executed (excap). Then, if lucky,print out all numbers with respective commands, and check that you won't get command lost from any other number.
fcpli
Satellite1900 (TechnicalUser) 22 Jul 11 9:14 Hi,next week I run the command and let you know.thank you very muchbye
Satellite1900 (TechnicalUser) 3 Aug 11 13:34 This night i try the command, but the excap does not work, same result lost command. I run on the same Sacos?
fcpli (TechnicalUser) 11 Aug 11 4:09 I am on leave, coming back next week. What you can do meanwhile,check sacop (mentioned before), address 1b0d should have value ff. Seems that there are more numbers with corrupt data
fcpli
Satellite1900 (TechnicalUser) 12 Aug 11 3:53 sorry, I expressed myself badly.the command "excape" failed before I run the "Sacos". I misunderstood what you wrote, and not being sure I have not run the Sacos. I will make another attempt next week.Thanks
Satellite1900 (TechnicalUser) 13 Sep 11 4:53 it works great!fcpli, how can I figure out where in memory worked in the future?Best regards \Satellite1900
MD110 - IP phones category changethread806-1648581Share This Forum Search FAQs Links Jobs Whitepapers MVPs
Find A Job or Post a Job Opening Click Here.jhonnyx (TechnicalUser) 16 May 11 10:03 Hello everybody and thanks for all your support,
I am not familiar with md110 ip phones but i need to change a category on one of those ip phones,
i need it to call outside of the premises, not only on the company phones, on other extensions i just change
teh category with excac or kscac, no clue about ip phones...
Thank you
doktor (IS/IT--Management) 16 May 11 16:13 In MX-ONE 3.2 and below: GEDIC:DIR=,CSP=;In MX-ONE 4.1 and up: extension -c -d XXXX --csp YY ///doktor
jhonnyx (TechnicalUser) 17 May 11 19:28 Thank you very much, i have to receive confirmation that it worked but i am sure it's all right
Thank you again.
Delay in ringingthread806-1640353Share This Forum Search FAQs Links Jobs Whitepapers MVPs
Check Out Our Whitepaper Library. Click Here.Faramir56 (TechnicalUser) 3 Mar 11 10:25 Hi all,is there anyone who can solve this riddle?An extension of my Ericsson MD110 start to ring only after three-four times after dialed number. The red light on telephon start to show, but ring tone start later. All parameters run OK.Thank you in advance,Faramir56
whosrdaddy (Vendor) 3 Mar 11 17:34
the CALALT setting is set to delayed ringing.If this is a digital handset (which i presume) push the program button and select the ringing signal with digits 0-6
/Daddy ----------------------------------------------------- What You See Is What You GetNever underestimate tha powah of tha google!
batkotivalio (IS/IT--Management) 26 Mar 11 7:20 You sould change CALALT to 1...
incoming external callsthread806-1641343Share This
Forum Search FAQs Links Jobs Whitepapers MVPs
contactnow (TechnicalUser) 11 Mar 11 8:35
Need help,All incoming (external) traffic from public, in one route has to go to switchboard operator number,no matter if they dial extension, all traffic to divert to operator.
System in use mxone-tsw.
Thank you
Monrovia (TechnicalUser) 11 Mar 11 9:28 use command RODNI:ROU=XX,TRU=X-XX&&X-YY,DAY=XXXX,NIGH=ZZZZ;
but what type of trunk? caller id? If caller identity activated, use NUTRI to direct the calls to operator extension
contactnow (TechnicalUser) 14 Mar 11 9:50 Hi Monrovia
Route type is SL60.Rodni does not help, it may be that something is missing.The idea is that all incoming calls day and night should be directed to switchboard number!(All incoming traffic has to go to switchboard number first)!
Thanks for help
parnum (TechnicalUser) 14 Mar 11 11:12
then it's a ddi route? use NUTRI as advised?
best parnum
Isinor (Instructor) 15 Mar 11 8:42 Hi
Try setting the call type with OPCTS, you might need to tweak CALT 5, 6 or 7 depending the the route configuration.
OPCTS:CORG=xx,CALT=5,ROU=rr; RegardsIsinor
External diversion - MD110thread806-1638650Share This Forum Search FAQs Links Jobs Whitepapers MVPs
Check Out Our Whitepaper Library. Click Here.
bart023 (TechnicalUser) 17 Feb 11 3:40 Hi All,
I'm using below command to divert calls on external cell number*22#external_cell_number# and it works fine , but currently on my cell phone I see that my office phone is calling me. I would like to see which number called to my office and is diverted.
Category on office phone:EXCCP:CAT=10;CAT TRAF SERV CDIV ROC10 00151515 0213110600 011150000 020001
Could You plese help me with this task??
doktor (IS/IT--Management) 17 Feb 11 3:56 You need to ask your telephone line provider for the service "CLIP-SA" (Calling Line Information Presentation - Special Arrangement).Not all providers can give you this feature - and anly if you use ISDN lines. ///doktor
bart023 (TechnicalUser) 17 Feb 11 4:38 Thanks doktor,I already ask our provider and waiting for response.
bart023 (TechnicalUser) 4 Mar 11 3:35 Hi,Operator said "It's not allowed"
but i have another question,when someone from our company (the same provider-internal incoming) call to number (internal) which is diverted to my mobile, is it possible to see which number called to my office and is diverted?
I understand that it's impossible to see another number (from other provider-external incoming) on my mobile. regards/bart
Alpha011 (TechnicalUser) 4 Mar 11 7:29 I think it depends on a number of factors . From your mobile i dont think this is possible.
If you are in your office or have access to a call logger and Winfoil/Extension Manager , you may work this out . This also depends on whether the caller has barred their number.
HTH
How to setup a siu card.thread806-1634331Share This Forum Search FAQs Links Jobs Whitepapers MVPs
Check Out Our Whitepaper Library. Click Here.
station51 (TechnicalUser) 13 Jan 11 18:57 Hi
I have a siu card that I need to setup on the md110 system.What are the coomands to setup the card using winfoil?
Does the NIU/2 card need to be in the rack to do this?
doktor (IS/IT--Management) 14 Jan 11 7:09 This is how to enable SMDR on a SIU board:
EDEQI:DEV=SI-0,EQU=x-x-xx-0;EDICC:DEV=SI-,BAUDR=9600,WORDL=8,STPBIT=1,PARITY=NO,PROC=NO;EDFII:FILE=SMDR;EDDFI:DEV=SI-0,FILE=SMDR;CLOHI:FILE=SMDR,FORM=2,DMPSIZ=2,DISCR=0;CLODI:FILE=SMDR;CLTGI;
Q:Does the NIU/2 card need to be in the rack to do this?A:Yes, in LIM=1.You use the NIU to login.
What software do you use in your MD110 system? ///doktor
station51 (TechnicalUser) 17 Jan 11 23:19 I am running BC12 Service pack 07 NIU/2 card.
What is command if i want to make a one extension thread806-1625748Share This Forum Search FAQs Links Jobs Whitepapers MVPs
Find A Job or Post a Job Opening Click Here.TYP3R10 (TechnicalUser) 28 Oct 10 12:07 what is the command if want to make an extension that can call only one or two extention , what i mean is for example i make 100 extentions, start from 3300 - 3399 but for extension 3300 and 3301 can call only from number 3302 - 3305(ex. 3300 and 3301 can call only 3302 - 3305) and it cannot call to other extension. please help me to this matter, your help is highly appreciated. Thanks.
Monrovia (TechnicalUser) 28 Oct 10 15:29 Try SPEXI - special purpose extensions
problem with cil over ethernet
thread806-1611377Share This Forum Search FAQs Links Jobs Whitepapers MVPs
user25 (TechnicalUser) 9 Jul 10 9:23 i've tried to configure cil over ethernet in MXONE (NIU2)butit dosn't work. please show me the mistake where it is.I've done:
ioeqi:iodev=cil2,equ=1-2-10-4,type=network,usage=out;ionci:iodev=cil2,rport=7000,ip=10.12.8.110;cldfi:file=taxlan,iodev=cil2,user=cil-2;clohi:file=taxlan,form=1,dmpsiz=1;clodi:file=taxlan,dial=09;cltgi;
i've also:cldfp;taxlan actiodev/path user device state prioritycil2 cil-2 passive c
at th pc where i wante to get cil report i used HyperTerminal connection with ip adress 10.12.8.2 (NIU ip adress) and number port 7000. the ip adress of the pc is 10.12.8.110
now when i try to open a connction i get a messge "imposible to connect to 10.12.8.2" however i can ping this adress from the pc!!
where is the problem???!!!
whosrdaddy (Vendor) 9 Jul 10 11:10 the problem is that the PBX acts as a telnet client and you need to setup a Telnet server. Hyperterminal is a telnet client.
/Daddy ----------------------------------------------------- What You See Is What You GetNever underestimate tha powah of tha google!
user25 (TechnicalUser) 11 Jul 10 3:55 please what is the telnet server aplication you recomand me to use?? NB: i've a pc with XP os.
cpux10 (TechnicalUser) 11 Jul 10 15:31 To test, you can use HyperTerminal and in the call menu, select "wait for a call". When the first record arrives, you will get connected and receive the call records from that point on.
phrankie (TechnicalUser) 13 Jul 10 5:11
hi user25,i had a similar problem once,you can download and install portpeeker on the machine then configure the port to listen to(7000 in this case) as well as the ip address,you should be able to see your call log information.
cheers!Phrankie!
user25 (TechnicalUser) 15 Jul 10 11:24 thanks phrankie i've used portkeeper it works well and very easy to configure it! thank you once again
IP phones over Internetthread806-1592911Share This Forum Search FAQs Links Jobs Whitepapers MVPs
todori (Programmer) 26 Feb 10 6:47 Greetings,
we are using MD110 TSW with IPLU cards (H.323 protocol). Recently we decided to open 1 IPLU IP address to Internet and bypass company firewall in order to allow phone calls over ADSL. When we did it, we cannot connect to IPLU card over Internet with physical IP phones. Strangely, when using PC with ACC (Aastra Communication Client) we can subscribe and talk from anywhere in the world with no problems (and no vpn connection but direct connection to Internet). When I connect IP phone (Dialog 4425) it cannot start and I have message "User not logged on". When I enter correct IP extension but wrong password phone recognizes it and alerts me that I have entered wrong password - that shoes there is some communication between IPLU and phone. Our Ericsson support says that it should work, and it really does work when using PC.Why do my physical phones not work this way and PC softphone does work?Thank you in advance.
parnum (TechnicalUser) 26 Feb 10 7:08
Have you http:// onto the phone to view debug log to see what happens, or done wireshark track on the phone?
best parnum
todori (Programmer) 26 Feb 10 8:15 I have checked web configuration of the physical phone. It seems that "Debug log" option does not work because last entry is from "70-01-01 00:00:00" and it is not changing with time.Option "show phone configuration" gives me
-------------------------------------------HW ver./Application CAA1580043 ver./Boot ver.:R2E/A/R7E/R3L
It's a DBC425 02 Extension Number: 3433The phone is NOT logged on!
The phone is configured for MX_ONECurrent gatekeeper IP:xxx.xxx.xxx.xxxBackup Gatekeeper IP Address: 0.0.0.0 Domain(from DHCP server):lanDomain(from config. file):DHCP is usedgatekeeperId:LIM*Configured TTL:600gH323Debug:0gkUsed:4Used TTL:540
IP Address:192.168.1.3Current software server IP:130.100.17.80Port 1 Link UP with 100 Mbps FULL DUPLEXPort 2 Link DOWN ----------------------------------------------------
IP address of the gatekeeper is correct, I just don't want to broadcast it :-)IP address of software server 130.100.17.80 is default address written in config file and I have not changed it. It appeared when I entered 0.0.0.0 to avoid problems with software server which is unavailable. I have placed config files on local computer on remote site and entered its IP address and it did not help.Is there a way for me to "unlock" debug log option? Wire Shark is beyond my knowledge and I would like to avoid it as long as possible :-)
Thank you in advance.
parnum (TechnicalUser) 26 Feb 10 11:53
[DebugLevel] H323Debug=4RTPDebug=4
in the config file sets the level, so change and reboot the phone to pick up change.
You need to stop avoiding Wireshark and start using it now and it will all become clearer, you will see your blocked path. I do not believe it is above your level, you just need to run it and look at where the packets fail.
best parnum
whosrdaddy (Vendor) 26 Feb 10 14:41 are you using the phone behind a router?
----------------------------------------------------- What You See Is What You GetNever underestimate tha powah of tha google!
todori (Programmer) 1 Mar 10 2:15 Thank you parnum I will definitely try WireShark.
whosrdaddy, yes phone is behind ADSL router.
whosrdaddy (Vendor) 1 Mar 10 3:26 H323 with NAT is asking for trouble.your router needs to be H323 aware.
http://www.technodata.org/files/technical/H323-NAT%20Technical%20Guide.htm
your best bet is using a fixed VPN connection over internet (for example juniper netscreen solutions)
/Daddy ----------------------------------------------------- What You See Is What You Get
Never underestimate tha powah of tha google!
todori (Programmer) 2 Mar 10 4:43 We are using CISCO vpn router, I think it is 871 and it works well, but now it is in Vancouver for Olympic games. I wanted to try to connect with ADSL for another event while Vancouver crew is away. I will have to wait for vpn router to come back then
Tnx.
Problem with ABBREVIATED COMMON thread806-1585518Share This Forum Search FAQs Links Jobs Whitepapers MVPs
Check Out Our Whitepaper Library. Click Here.emags (TechnicalUser) 7 Jan 10 1:53 Hi guys, Happy New year 2010..!
Back to matter, i'm having a problm with ABB numbers.I ended a ABB number using; ADCOE:ABB=5995; So that i can reprogram it to a new mobile number using ADCOI:ABB=5995,TRA=04767529475,CLASS=0&1&2&3,NPRES=1; But the fun thing is, once i dial the it it shows that number is vacant! when i print it the number is there 5995 04767529475 0123 1...?What might be a problem, I need your help!
thx.
parnum (TechnicalUser) 8 Jan 10 8:15 try
ADCOE:ABB=5995;NANSE:NUMSE=5995,NUMTYP=AC;NANSI:NUMSE=5995,NUMTYP=AC;ADCOI:ABB=5995,TRA=04767529475,CLASS=0&1&2&3,NPRES=1;
best parnum
program0 (TechnicalUser) 12 Jan 10 6:27 dont forget you need to add your external dest code to the beginning of the TRA if going to a mobile or external landline!! It's never too late to try something new
RODDI COMMANDthread806-1582336Share This Forum Search FAQs Links Jobs Whitepapers MVPs
bagao (TechnicalUser) 8 Dec 09 23:23 I dont understand about RODDI command.Here is my scenario.I need to route a group to analog trunk,when have call to this analog,all extension of this group will be ring.I don't have Alex library.Please help me to do that.Thanks a lot.PS: this is route on MXONE TSW<RODAP:ROU=ALL;ROUTE DATAROU TYPE VARC VARI VARO FILTER 1 TL11 H'00000012 H'00000109 H'00002815 NO59 SL60 H'00100200 H'00000000 H'00010000 NO60 SL60 H'00100200 H'00000000 H'00010000 NO61 SL60 H'00100200 H'00000000 H'00010000 NO62 SL60 H'00100200 H'00000000 H'00010000 NO63 SL60 H'00100200 H'00000000 H'00010000 NO66 TL65 H'00000110 H'00000001 H'00000000 NO73 SL60 H'00000310 H'15400000 H'16400000 NO74 SL60 H'00000310 H'15400000 H'16700000 NO and <ROCAP:ROU=ALL;ROUTE CATEGORY DATAROU SEL TRM SERV NODG DIST DISL TRAF SIG BCAP1 0110000000000010 4 3100100100 0 30 128 00151515 400000000000 00110059 0110000000000010 5 3100000001 0 30 128 00151515 511110000030 11111060 7110000000000010 5 3100000001 0 30 128 00151515 111110000030 11111061 7110000000000010 5 3100000001 0 30 128 00151515 111110000030 01111062 7110000000000010 5 3100000001 0 30 128 00151515 511110000030 11111063 7110000000000010 5 3100000001 0 30 128 00151515 511110000030 11111066 7110100000000010 5 2110000007 0 30 128 00010115 011110121191 11111173 7110000000000010 5 3100000001 0 30 128 00020215 111100000031 11111074 7110000000000010 5 3100000001 0 30 128 00020215 111100000031 111110
Monrovia (TechnicalUser) 9 Dec 09 1:47 Post RODNP:ROU=1,TRU=ALL;
your route 1 is analog trunk. is that the same trunks u want to make changes?
bagao (TechnicalUser) 9 Dec 09 2:45 Hi MonroviaROU TRU DAY NIG
1 001-1 16000 160001 001-2 16000 160001 001-3 16000 160001 001-4 10063 100631 001-5 10063 100631 001-6 10063 100631 001-7 10063 100631 001-8 38004 38004
ENDYes, I just have 1 analog trunk connect to MXONE.Please instruct me how to route it?Thanks
Monrovia (TechnicalUser) 9 Dec 09 3:18 I hope you might have understood from the above post. It is as simple as that. just read the lines.
route = 1. in one trunk board you have 8 trunk lines. and each trunk line is assigned to different extensions
in day mode as well in night mode.
use command RODNI
RODNI:ROU=1,TRU=01-1,DAY=11111,NIG=xxxxxx;
same for each TRU
bagao (TechnicalUser) 9 Dec 09 4:18 Thanks a lot Monrovia!I create analog trunk,it works well.If you don't mind,please keep in touch, I should to learn from you a lot
roddi command for a numbering range?thread806-1581199Share This Forum Search FAQs Links Jobs Whitepapers MVPs
REP000 (TechnicalUser) 1 Dec 09 10:30 I need a roddi command for a numbering range.If i get a single number, this command is shuch this:roddi:dest=8989,rou=50,...;But if i want to do this for a numbering range (8000-8975), exist any command in MD-110 PBX for it?
Otherwise I would have to do:roddi:dest=8000,rou=50,...roddi:dest=8001,rou=50,......
roddi:dest=8975,rou=50,..
(976 times!)
norrman (TechnicalUser) 1 Dec 09 11:29 Or you could trydest=80dest=81..dest=88dest=890..dest=896dest=8970..dest=8975(22 times)
parnum (TechnicalUser) 1 Dec 09 13:20
takes 5 minutes to write in excel and export as txt file tab delimited and then run in winfiol F2 in the way described.
best parnum
denicvne (TechnicalUser) 1 Dec 09 13:44 If i have destination range as you have i will define destination 8 to route 50 and job is done!
parnum (TechnicalUser) 1 Dec 09 17:13
8976 to 8999 are not dest codes so that's not correct
best parnum
mundus (TechnicalUser) 4 Dec 09 10:54 use PNR - it's simpel and it's working !
CAN MAKE ALL EXT CALL TO OPERATOR ONLYthread806-1565403Share This Forum Search FAQs Links Jobs Whitepapers MVPs
ALTAMIMI (MIS) 20 Aug 09 14:06 CAN MAKE ALL EXT CALL TO OPERATOR ONLY?
I HAVE 1800 EXT ANALOG AND DIGITAL NEED ONLY CALL TO 9 THE OPRETOR AND THY CAN NOT CALL TO GITHAR OR TAK TRANK LIN;
HOW I MAKE THAT IF I CAN FROM TRAFFIC MATRIX?
asuvp (Programmer) 21 Aug 09 0:35 It is easier to read your question if the CAPS-lock is off.
ALTAMIMI (MIS) 22 Aug 09 14:12 Can make all EXT call to Operator only? i have 1800 EXT analog and digital need only call to operator "9" and thy can not call together or trunk line.how i make that?
Monrovia (TechnicalUser) 23 Aug 09 4:33 you would like to block all your extension making external calls? and they should call only operator?
pls post CADAP; NADAP; & TCMAP;
ALTAMIMI (MIS) 24 Aug 09 3:25 <CADAP;CALENDAR DATAVERSION=CXP1010104/4/TSWSP04/R5A13:25:48MON 10 AUG 2009END
<NADAP;
NUMBER ANALYSIS DATA TYPE OF SERIES NUMBER SERIES EXTENSION NUMBER SERIES 1000 - 1030 1032 - 1050 2000 - 2887 28889 2889 - 3832 3900 - 3910 3999 4400 - 4900 6666EXTERNAL DESTINATION CODE 0 60 - 63 700 - 709 8OPERATOR INDIV. NUMBER SERIES 5001 - 5007OPERATOR COMMON NUMBER SERIES 9OPERATOR COM. DID. NUM. SERIES 9ABBREVIATED COMMON NUMBER SERIES 4000 - 4398COMMON PUBLIC DIRECTORY NUMBER 28888DIRECT INWARD SERVICE ACCESS 1031TYPE OF SERVICE CODE SERVICE CODE ANSWER ON CALL TO COMMON BELL 55EXTERNAL NUMBER LENGTH DATA EXTERNAL NUMBER NUMBER LENGTH019 4 - 902 4 - 804 4 - 863 9 - 20PROCEED TO SEND SIGNAL DATA EXTERNAL NUMBER POS. TYPECALL DISCRIMINATION DATA EXTERNAL/INTERNAL NUMBER CAT 011 8 5 3 01700 5 3 019 8 5 3 02 10 9 8 6 5 3 2 03 5 3 04 10 9 8 6 5 3 2 08 10 9 6 5 3 2 0902 10 9 8 5 3 2 0903 10 9 5 3 2 0904 10 9 8 5 3 2 0905 10 9 8 5 3 2 0906 10 9 5 3 2 0907 10 9 8 5 3 2 0908 10 9 5 3 2 0909 10 9 8 5 3 0919 5 3 0920 10 9 6 5 3 2 0930 5 3 0939 8 6 5 4 3 2 0940 10 9 8 6 5 3 2 0961 8 5 3 2 0963 5 3
0992 10 9 8 6 5 4 3 2 0993 10 9 5 3 2 0996 10 9 5 3 2 0997 10 9 5 3 2 0998 10 9 5 3 2 0999 10 9 5 3 2 1 10 9 8 6 5 4 3 2 12 10 9 8 6 5 4 3 2 13 10 9 8 6 5 4 3 2 14 10 9 8 6 5 4 3 2 160 8 5 61 9 62 10 63 9 8 7 6 5 4 3 2 6666 10 9 8 7 6 5 4 3 2 1 0701 5 705 11 706 10 4 3 2 1 8 10 9 8 6 5 9 10 9 8 6 5 3 2 1 0END
<TCMAP:CON=ALL;TRAFFIC GROUP MATRIX DATACON = T BA 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 0 1 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 2 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 3 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 4 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 5 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 1 6 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 7 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 8 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 9 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 110 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 111 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 112 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 113 1 1 0 0 0 0 0 0 0 0 0 0 0 1 1 114 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 115 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1CON = C BA 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 2 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 3 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 4 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1
5 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 6 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 7 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 8 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 9 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 110 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 111 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 112 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 113 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 114 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 115 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1END
Monrovia (TechnicalUser) 24 Aug 09 3:40 change the CAT of all extension to 1
parnum (TechnicalUser) 24 Aug 09 9:46
We need to see EXCCP:CAT=ALL: as well to check the CAT, CD number is in day/night TRAF of CAT, which is related to TCMAP for extension and route. Pls send EXCCP print, TCMAP does not show CAT number.
best parnum
ALTAMIMI (MIS) 24 Aug 09 11:07 <EXCCP:CAT=ALL;EXTENSION CATEGORY CODE CAT TRAF SERV CDIV ROC 0 00000014 0202120100 000000000 0000011 00010114 0202120100 000070000 0000012 01020213 0202120100 000070000 0000013 01050513 0202120100 000070000 0000014 03020213 0202120100 000070000 0000015 01050513 0202120700 011150000 0000016 01060613 0202120700 011150000 0000017 03060613 0202120700 001150000 0000018 03030313 0202120300 000070000 0000019 00090915 0202120700 011150000 00000110 01030313 0202120700 001150000 00000111 00010114 0202020100 000071000 00000112 01020213 0202020100 000071000 00000113 01060613 0202020100 000071000 00000114 01020213 0202120100 000071000 00000115 01050513 0202120100 001150000 00000116 01060613 0202120100 001150000 00000117 02060613 0202020100 111150000 00000118 00000000 0000000000 000000000 00000119 00101015 0202120700 011150000 00000120 02090915 0215120700 111151321 00000121 00000000 0000000000 000000000 00000122 03020213 0202120300 000070000 00000123 00000000 0000000000 000000000 00000124 00000000 0000000000 000000000 000001
25 00000000 0000000000 000000000 00000126 00000000 0000000000 000000000 00000127 00000000 0000000000 000000000 00000128 00000000 0000000000 000000000 00000129 00000000 0000000000 000000000 00000130 01040413 0202120100 000070000 00000131 00000000 0000000000 000000000 00000132 00000000 0000000000 000000000 00000133 00000000 0000000000 000000000 00000134 00000000 0000000000 000000000 00000135 00000000 0000000000 000000000 00000136 00000000 0000000000 000000000 00000137 00000000 0000000000 000000000 00000138 00000000 0000000000 000000000 00000139 00000000 0000000000 000000000 00000140 02080813 0202120700 011141111 00000141 00000000 0000000000 000000000 00000142 00000000 0000000000 000000000 00000143 00000000 0000000000 000000000 00000144 00000000 0000000000 000000000 00000145 00000000 0000000000 000000000 00000146 00000000 0000000000 000000000 00000147 00000000 0000000000 000000000 00000148 00000000 0000000000 000000000 00000149 00000000 0000000000 000000000 00000150 00000000 0000000000 000000000 00000151 00000000 0000000000 000000000 00000152 00000000 0000000000 000000000 00000153 00000000 0000000000 000000000 00000154 00000000 0000000000 000000000 00000155 00000000 0000000000 000000000 00000156 00000000 0000000000 000000000 00000157 00000000 0000000000 000000000 00000158 00000000 0000000000 000000000 00000159 00000000 0000000000 000000000 00000160 00000000 0000000000 000000000 00000161 00000000 0000000000 000000000 00000162 00000000 0000000000 000000000 00000163 00000000 0000000000 000000000 000001
MINIMUM CATEGORY CODE FOR AUTHORIZATION CODE IS 02DEFAULT CATEGORY CODE FOR AUTHORIZATION CODE IS 02
END
parnum (TechnicalUser) 26 Aug 09 7:56 Set up with EXCCS new CAT 18 with TRAF xx1111xx, and NACDS:NUM=9,CDCAT=11;
Put extensions in CAT 18, then they can only dial 9 for operator. Operators are TRAF=15 so they can call any number and do not look at CDCAT.
Also TCMAS:A=11,B=11,CON=ALL;TCMAS:B=11,A=11,CON=ALL;
You also need to NACDS in your emergency number so extensions can call emergency services at all times in case of workers in emergency where no operator is available.
best parnum
HOW TO REPLACE THE 4 DIGIT TO 5 DIGIT & DEST FROM 0 TO 9?thread806-1563501Share This Forum Search FAQs Links Jobs Whitepapers MVPs
Find A Job or Post a Job Opening Click Here.ALTAMIMI (MIS) 10 Aug 09 7:40 I HAVE 1000 ANALOG EXTENITON AND 900 DIGITAL EXTENITON EVRY EXTENITON HAVE 4 DIGIT TO 5 DIGIT AND ALL THESE EXTENITON MAKE E1 TLU76\3?HOW THE ESYE WAY TO CHANGE ALL EXTENITONS AND THE DIGITAL EXTENITON HAVE FUNCTION KEY'S
doktor (IS/IT--Management) 10 Aug 09 9:43 You can use the NUTRI command to convert from 4 to 5 digits, or end all numbers (EXTEE/KSEXE) and initiate them al again by EXTEI/KSEXI. ///doktor
ALTAMIMI (MIS) 10 Aug 09 13:53 thanks Mr. doktor
how abut PC-REGEN i take from MD110(TSWSP4). i thenk i can replace from some command but i do not know wich file i have to change?
doktor (IS/IT--Management) 11 Aug 09 2:49 Hi ALTAMIMI
We use a very good text editor called TextPad.You can take you re-generated INI files, like e.g. EXTEI, and add the 5 digit by marking it in TextPad "block mode".The marked area can be changed, deleted or digigts could be added.E.g.EXTEI;DIR=5644,CAT=15,EQU=1-1-22-11,TYPE=EL6;If 7 should be added "75644", the area in the text file just before the digit 5 is marked - top to buttom of the file - and the digit 7 is added to all lines.Easy and fast! ///doktor
DUFQI (TechnicalUser) 11 Aug 09 3:49 If you are using a new numberrange just use KSDNC and EXDNC
doktor (IS/IT--Management) 11 Aug 09 7:40
Take care using " KSDNC and EXDNC ". You MD may reload if you have high traffic. ///doktor
ALTAMIMI (MIS) 11 Aug 09 8:43 THANKS FOR ALL
ABUT "EXDNC" AND "KSDNC" I CAN NOT USE IF THE EXTENTION HAVE PARALLEL RINGING.I MAKE RE-GENERATED FORM PC-REGEN I WILL TRAY FROM THERE
I CHANG IN "KSEXI" AND "EXTEI"BUT WICH COMMAND I HAVE TO CHANGE ELSE
doktor (IS/IT--Management) 11 Aug 09 9:10 You need to change also your groups GHDAP:GRP=ALL; and ACD groups.If you check your number analysis (NADAP;) you will see all active (existing) numbers. ///doktor
whosrdaddy (Vendor) 12 Aug 09 8:31 Altmamimi,
first of all don't use CAPS in your post, it is considered as shouting. About your question: yes it's best to use PC-REGEN to create a new system.
so steps to be taken:
1) take a full PC-REGEN printout from your PBX (this file can be generated from PC-REGEN) and must be sent with winfiol. Regenerate initiate commands from printout files using PC-REGEN.2) edit all files, changing all the required extension numbers3) start a new system from INL, load license and send LIM disposition file.4) send initiate command files to PBX with winfiol
If you have not fully understood what I'm trying to explain here, then don't do it, you must have full knowledge of the MD110 to achieve this task. Do you have a local service provider? They should be able to do this work for you.
Cheers,Daddy ----------------------------------------------------- What You See Is What You GetNever underestimate tha powah of tha google!
ALTAMIMI (MIS) 12 Aug 09 16:56 thanks to all
i chang all extentions from file "KS" and "EX" this is "NADAP" for my system
<NADAP;NUMBER ANALYSIS DATA TYPE OF SERIES NUMBER SERIES EXTENSION NUMBER SERIES 1000 - 1030 1032 - 1050 2000 - 2887 28889 2889 - 3832 3900 - 3910 3999
4400 - 4900 6666EXTERNAL DESTINATION CODE 0 60 - 63 700 - 709 8OPERATOR INDIV. NUMBER SERIES 5001 - 5007OPERATOR COMMON NUMBER SERIES 9OPERATOR COM. DID. NUM. SERIES 9ABBREVIATED COMMON NUMBER SERIES 4000 - 4398COMMON PUBLIC DIRECTORY NUMBER 28888DIRECT INWARD SERVICE ACCESS 1031TYPE OF SERVICE CODE SERVICE CODE ANSWER ON CALL TO COMMON BELL 55EXTERNAL NUMBER LENGTH DATA EXTERNAL NUMBER NUMBER LENGTH019 4 - 902 4 - 804 4 - 863 9 - 20PROCEED TO SEND SIGNAL DATA EXTERNAL NUMBER POS. TYPECALL DISCRIMINATION DATA EXTERNAL/INTERNAL NUMBER CAT 011 8 5 3 01700 5 3 019 8 5 3 02 10 9 8 6 5 3 2 03 5 3 04 10 9 8 6 5 3 2 08 10 9 6 5 3 2 0902 10 9 8 5 3 2 0903 10 9 5 3 2 0904 10 9 8 5 3 2 0905 10 9 8 5 3 2 0906 10 9 5 3 2 0907 10 9 8 5 3 2 0908 10 9 5 3 2 0909 10 9 8 5 3 0919 5 3 0920 10 9 6 5 3 2 0930 5 3 0939 8 6 5 4 3 2 0940 10 9 8 6 5 3 2 0961 8 5 3 2 0963 5 3 0992 10 9 8 6 5 4 3 2 0993 10 9 5 3 2 0996 10 9 5 3 2 0997 10 9 5 3 2 0998 10 9 5 3 2 0999 10 9 5 3 2 1 10 9 8 6 5 4 3 2 12 10 9 8 6 5 4 3 2
13 10 9 8 6 5 4 3 2 14 10 9 8 6 5 4 3 2 160 8 5 61 9 62 10 63 9 8 7 6 5 4 3 2 6666 10 9 8 7 6 5 4 3 2 1 0701 5 705 11 706 10 4 3 2 1 8 10 9 8 6 5 9 10 9 8 6 5 3 2 1 0END
how to change "0" to "9" for all system frme PC-REGEN?
aftare i change evry thing i will make REL for system
whosrdaddy (Vendor) 12 Aug 09 17:46 you need to change the number for your operator.
as you can see in nadap, operater nr is now 9 (OC and OD).
so assign it another nr, then you can put 9 in ED range and program RODDI.
/Daddy ----------------------------------------------------- What You See Is What You GetNever underestimate tha powah of tha google!
ALTAMIMI (MIS) 13 Aug 09 6:27 HI EVRY BODYTHIS COMMAND I TAKE IT FROM PC-REGENWICH COMAND FROM THIS I HAVE TO CHANG THE DEST FROM 0 TO 9?GSMULTCNBOI CNBRI IOBPI IONPC IOEQI IOIFC IOFDC ALEOI ALDAS ALULS IOCAC SYDAS SYTDS ASPAC TCMAS
NUMANALNUTRI OPERI OPISS EXCCS GESPI ADCOI ROCAI RODAI RODDI GEDII IPBOI IPEXI IPGKC EXTEI KSEXI KSANIKSMDI KSFKC GHGRIGHGMI ACPAC ROEQIOPCTSOPCGSOPADCOPRSCOPDNC CPDNIRODNILCTDICLCCCAUCOIKSTSCKSCHC GETSCCXSYCSPEXICDINICASIICHCMIGEFKI
Monrovia (TechnicalUser) 13 Aug 09 6:52 Note: If you dont have some expertise in reading & executing commands, dont try these steps. These steps will make your operator & outgoing calls Dead.
Using WINFIOL
NANSE:NUMSE=9,NUMTYP=OC;NANSE:NUMSE=9,NUMTYP=OI;you end the Operator Common no & Operator Individual no.
NANSI:NUMSE=5000,NUMTYP=OC;NANSI:NUMSE=5000,NUMTYP=OI;You initiate OC & OI as 5000, which is free in your number series.(1,2,3,4,5XXX,6,7,8&9 already in use)Once you converted your Dest 0 to 9, you may make operator as 0 which may be free to use at that time.(for the time being there will be no calls to operator) So take care, your Operator parameters has to be set accordingly.
NANSI:NUMSE=9,NUMTYP=ED;you initiate ED in number series
now initiate the route parameters, for which need your RO details, roodp, rocap, roeqp, rodap, rodnp, etc
ALTAMIMI (MIS) 14 Aug 09 6:43 THAKS ALL I WILL TRY IT AND TELL YOU WHAT HAPEN.
How To Remove Additional Numberthread806-1557422Share This Forum Search FAQs Links Jobs Whitepapers MVPs
hisyam74 (TechnicalUser) 5 Jul 09 20:53 Hi Everybody!
Can you all help me how to remove additional number? Here are the details. <CADAP;CALENDAR DATAIDENTITY=UTMSKUDAI VERSION=CXP1010119/4/TSWSP03/R4A08:58:09MON 06 JUL 2009END < <SUDIP:DIR=33999;DIRECTORY INFORMATION AT 08:55:41 06JUL09DIRECTORY NUMBER : 33999TYPE OF DIRECTORY NUMBER : ATSNAME : ADDITIONAL NUMBER : 33123
EXTENSION TERMINAL DATAEQU TERMD ADN4-0-52-12 0000000
EXTENSION DIRECTORY CATEGORIESCAT TRAF SERV CDIV ROC TRM ADC CUST LANG BSEC MCOST10 03151515 0015110700 001151000 000001 0 010000301 - 0 -
EXTENSION MULTIPLE DIRECTORY NUMBER DATA
DIR KEY CALALT*33999 - - 33123 06 0
GROUP DATA
PARALLEL RINGING DATA
DIVERSION DATA
PAGING DATA
END <
doktor (IS/IT--Management) 6 Jul 09 10:01 Try with EXTEE:DIR=33123; ///doktor
hisyam74 (TechnicalUser) 6 Jul 09 19:57 Hi doktor!!
I've try EXTEE:DIR=33123;...,still cannot remove the additional number, any idea? Please help me
doktor (IS/IT--Management) 7 Jul 09 3:30 Let me have these printouts...SUSIP:DIR=33999;SUDIP:DIR=33123;SUSIP:DIR=33123; ///doktor
Belyaev (TechnicalUser) 7 Jul 09 4:50
EXADC:DIR=33999,ADDNUM=33999;
hisyam74 (TechnicalUser) 7 Jul 09 11:06 Hi Belyaev!!
Thanks for the helpful tips..., it works and thanks again..
code to access main/Tie lines..thread806-1540067Share This Forum Search FAQs Links Jobs Whitepapers MVPs
amalpbx12 (TechnicalUser) 31 Mar 09 9:27 Hi guys,
here I am again guys,I have a hot question 4 u.I know that there is a code in md110 BC10 to access main lines and Tie-lines.It is something like *0*Route*xxxx#
my question is:Is there any command to tell you what the code is?
really I'll be gr8ful F U could reply as soon as possible.
thanx guys. To ALREI or not to ALREI,this is the command
parnum (TechnicalUser) 31 Mar 09 9:47
ROEDP:ROU=x,TRU=ALL;
give you the lim and trunk number like 1-03.
RODRP:ROU=x;
give you the dest code
*0*103#DEST then number
RODDP:DEST=y;
give you route number if you do not know it
best parnum
routesthread806-1541371Share This Forum Search FAQs Links Jobs Whitepapers MVPs
Tek-Tips Forums is Member Supported. Click Here to donate.ehsan62 (IS/IT--Management) 6 Apr 09 23:55 hi!I have a question about routes in md110.we have many co(trunk) in our office that each belongs to one person. also each person have an extension and we want that when one person dials 0 he could reach to his own external number (for example his extension is 101 and his own external number is 8519600 and we want that when he dials the number 0 he could access the external number). I could'nt find any way, can you help me about this?thanks
Isinor (Instructor) 7 Apr 09 5:22
Hi,
The 'Customer Group' might be able to do this... if you have less than 250 co(trunks)
More info in ALEX \Solution Documents\Customer Group
EXCUC:DIR=...,CUST=1;KSCUC:DIR=...,CUST=1;
RODDI:DEST=...,CUST=1,ETC...;
RegardsIsinor
How to make all external telephone numbers jump to switchboard?thread806-1517440Share This Forum Search FAQs Links Jobs Whitepapers MVPs
srad (Programmer) 4 Dec 08 10:42 Hi,
How to make (when call a officce number) for all external telephone numbers (that they not answer or not localizable)jump to switchboard?
Regards,Toni.
kank (IS/IT--Management) 4 Dec 08 10:50 I think you mean if someone dials an outside number first the call shall visit the switchboard.Or you want to forward all incoming calls to visit operator. If it is the second one, what type of trunks do you have (analog, PRI)
srad (Programmer) 4 Dec 08 11:10 How to make a trunks?I want to the same one than PELPI instruction, but to do it for everyone is very laborious.Is possible to do it?
Regards,Toni
kank (IS/IT--Management) 4 Dec 08 11:21 I got it now.For example your operator common number is 9.Try CDCOI:INTDIV=9,PUBDIV=9,PRIDIV=9;This forwaring is common for the exchange. Unless you give individual diversion or personal number (CDINI or PELPI). This will work for all extensions.
srad (Programmer) 4 Dec 08 12:00 Thanks for all kank.
whosrdaddy (Vendor) 4 Dec 08 12:13 our you can use rerouting:
RODNI:ROU=x,DAY=9,NIG=9;
where x is your incoming route
/Daddy ----------------------------------------------------- What You See Is What You GetNever underestimate tha powah of tha google!
additional new limthread806-1505466Share This Forum Search FAQs Links Jobs Whitepapers MVPs
kscac (TechnicalUser) 8 Oct 08 2:04 we have 3 md 110 system in our company (BC 13),We are planning to add 1 lim.can somebody give me the step by step command how to add new LIM.
kank (IS/IT--Management) 8 Oct 08 10:11
1 Check that the system is correct by using command ALLIP and command HIMDP 2 Check that the backup unit is connected to the I/O bus. 3 I there is any previous initial load directory present on the hard disk, remove the previous initial load directory from the hard disk. 4 Create an initial load directory in the existing system.5 Make sure that the storage device has enough space for a system dump. 6 Check that the PCM lines, extensions, external lines, and PABX operators are connected.7 Switch on the DC/DC unit in the new LIM(s). 8 Are any fuse lamps lit on the new LIM(s)? 9 Check the fuses in the DC/DC unit. See installation test instructions for INSTALLATION TESTING OF ASB 501 04 . 10 Press the restart button on the LPU board in the new LIM(s).11 If there is voice compression on any PCM-line or is the line AMI-coded or similar change the time slot categories for the PCM-line(s) in the I/O LIM by using command GJTSC . The configuration of the PCM-lines in the I/O LIM must reflect the worst line in the system, because the selection of the time slots for loading is made in the I/O LIM. Time slots used for voice compression cannot be used for loading.Verify by using command GJTSP .12 Install licence data. 13 Order generation and transmission of the LIM disposition table for the new LIM(s) by using commands CNLDI and CNLDT . Completely new programs not included in the initial load directory should not be included in the LIM disposition table. These programs should be added separately after addition of LIM. 14 Order distribution of the program units from the initial load directory by using command LAPUT . Await printouts LOADING INFORMATION, (obtained immediately) LOADING WAS SUCCESSFUL, (obtained after about 20 minutes) and START PHASE 1, 1.3 AND PHASE 1.5 READY (obtained after some minutes). If the LPU display is used on any of the existing LIMs, 101 will be shown. 101 remains which is correct. 15 Initiate PCM-lines by using command GJLII. This is done for every line. 16 Initiate signalling links distribution using command ILLAI . 17 Verify group switch status by using commands GJLCP , GJLSP and SCICP . 18 If there is voice compression on any PCM-line change the time slot categories for all PCM-lines in the system by using command GJTSC. Note: The configuration of the PCM-lines in the I/O LIM must reflect the worst line in the system, because the selection of the time slots for loading is made in the I/O LIM. Time slots used for voice compression cannot be used for loading. 19 Order a complete clock control of the group switch by using command SCICI. 20 Verify the complete control of the group switch by using command SCICP.21 Initiate start-up of the added LIM by using command SFLII.22 Deblock the tone sender, the tone receiver, the conference equipment and the multi frequency equipment in the new LIM.23 Read out the alarm log by using command ALLIP and deal with alarms (if any).
24 Check the fault signal buffer by using command HIEDP or HIMDP.25 Make a system dump of the changes. By making a system dump at this point problems are avoided in case the reading of exchange data should fail.
kscac (TechnicalUser) 9 Oct 08 16:16 kank,
thank you very much for your quick response and for your help.youre the best.good luck.
Satellite1900 (TechnicalUser) 10 Oct 08 5:21 When you add to your system lim number 4 or number 8 lim need to redo the package because there are units that are common program end up in such lim.Otherwise the existing lim would be overloaded.
Satellite1900 (TechnicalUser) 10 Oct 08 5:21 When you add to your system lim number 4 or number 8 lim need to redo the package because there are units that are common program end up in such lim.Otherwise the existing lim would be overloaded.
kank (IS/IT--Management) 10 Oct 08 8:26 kscac,
no big thing, just copy paste from alex :)
second call to operator not ringthread806-1502212Share This Forum Search FAQs Links Jobs Whitepapers MVPs
kscac (TechnicalUser) 23 Sep 08 1:49 when the operator answer the first call,he hear the ring but when there is another incoming call while the operator is busy to the first caller,the operator cannot hear the ringing on second caller.
whosrdaddy (Vendor) 23 Sep 08 1:53 this is logical because the call is in the operator queue. ----------------------------------------------------- What You See Is What You GetNever underestimate tha powah of tha google!
kank (IS/IT--Management) 23 Sep 08 6:29 Do not mix operator usage with digital set. Most companies(especially small capacity) want to give operators some other jobs near being an operator. They want to use operators as secretaries, receptionists etc. In those cases we offer digital phones with ACD definitions.In your case, on operator display there is a notification that shows how many people waiting on the queue.
pcasi (TechnicalUser) 23 Sep 08 12:49 You can try initiating the operator with parameter MODE=1, eg.
OPERI:DIR=XXXX,MODE=1,EQU=A-BB-C,..........;
That would give you more audible signals but i´m not sure if it would ring the second call as normal call.
b17liviu (TechnicalUser) 2 Oct 08 4:40 Try OPISS:DIR=XXXXX,MODE=1;
why the trunks was disconnected after a period of time (3 min).thread806-1497635Share This Forum Search FAQs Links Jobs Whitepapers MVPs
b17liviu (TechnicalUser) 1 Sep 08 2:17
HI,
Please help me with this case on my MD110: I have ROU=3 TL11 route; after 2-3 min the call is automatically disconected and I do not understand why.
This is route setting:
<RODAP:ROU=3;ROUTE DATAROU TYPE VARC VARI VARO FILTER 3 TL11 H'00000012 H'00000188 H'00002845 NO
<ROCAP:ROU=ALL;ROUTE CATEGORY DATAROU SEL TRM SERV NODG DIST DISL TRAF SIG BCAP3 7110000000000010 4 2000000000 0 30 128 00151515 300000000000 001100
<CADAP;CALENDAR DATAIDENTITY VERSION=CXP1010110/2/BC12SP10/R7A14:37:34WED 27 AUG 2008
rfpui (TechnicalUser) 2 Sep 08 12:17 Try VARO=000020C5 or VARO=000020D5 ----------------------------------If anything can go wrong, it will.(Murphy's Law)
b17liviu (TechnicalUser) 3 Sep 08 2:02
i fix the problem for an moment with that:-remove PARNUM=41,PARVAL=180 with PARNUM=41 ,PARVAL=600
fcpli (TechnicalUser) 3 Sep 08 13:16 Your MD seems to wait for a B-answer from the PSTN, which is never received. Change VARO to 00002805 (or 2815). This should make the trick
b17liviu (TechnicalUser) 4 Sep 08 2:00
If i change VARO to 00002805 the route not dial,the route dial with only varo 00002845 .
fcpli (TechnicalUser) 4 Sep 08 5:11 Strange....Is this line connected to a PSTN or some kind of other equipment?The B-answer (if any) is received from the external party, and before this parameter has any affect, the dialling procedure should already be ready. In your case, the dial tone is sent from the MD, change sig d1 to e.g. 1, can you hear the dial tone from the external after dialling the dest? What about nuber length and roddp?Then, which board type are you using? TLU75?
b17liviu (TechnicalUser) 5 Sep 08 2:00 HELLO!
The line is connecting to private PBX (TOPEX with DTMF board) I using TLU 75 board. Yes i can hear the dial tone (TOPEX diall ton )after dialling the dest=77. The number length is not setting. I change the SIG=100010000000;but is the same situation.
<RODDP:DEST=77;EXTERNAL DESTINATION ROUTE DATADEST DRN ROU CHO CUST ADC TRC SRT NUMACK PRE77 3 0005000000000250000000000 0 3 0
END <RODRP:ROU=3;EXTERNAL DESTINATION DATAROU DEST 3 77
END <ROEDP:ROU=3,TRU=ALL;ROUTE EQUIPMENT DATAROU TRU EQU IP ADDRESS SQU INDDAT CNTRL 3 001-1 001-0-42-06
END Thank you for all fcpi.
b17liviu (TechnicalUser) 8 Sep 08 1:33 HELLO fcpli, do you have eny idea about this ; sorry for my english.
kank (IS/IT--Management) 8 Sep 08 8:57 hi try in VARO respectively 00002855, 00002865, 00002875
b17liviu (TechnicalUser) 8 Sep 08 11:50
HI
I try , but my route dial with only varo 00002845 .
pcasi (TechnicalUser) 8 Sep 08 16:50 Have you tried ?
ROCAC:ROU=3,SIG=300110000000;
fcpli (TechnicalUser) 9 Sep 08 11:47 Hi
I have no clear idea. But maybe a trace helps to figure this out...So, trace TLP11, start before dialling, and stop after the disconnection. stisr;stuni:unit=tlp11;sttsi:tri=1;sttse:tri=1;Log filestrap:tri=1;
and post it here
b17liviu (TechnicalUser) 12 Sep 08 8:36 Hi, fcpliThis is my trace TLP11:
<strap:tri=1;TRACE IND READ RESULTTRACE INDIVIDUAL NO 1TIME LINE(S)14.45.16.160 00001 HWSW SIGNAL IDENTY (H'0016) FROM EQU NO 1-0-42-00 TO TLP11 (H'0391) EXE A IN LIM 001 WITH 0 1 2 3 4 5 6 7 8 9 000 H'00 H'62 H'4C H'C7 H'00 H'00 H'00 H'00 H'00 H'00 010 H'00 H'00 H'00 H'00 H'00 H'00 H'00 H'00 H'0014.45.16.160 00002 SWSW SIGNAL BORDIDENTY (H'001E) FROM TLP11 (H'0391) EXE A IN LIM 001 TO DCP (H'007E) EXE A IN LIM 001 WITH 0 1 2 3 4 5 6 7 8 9 000 H'00 H'90 H'00 H'4C H'C7 H'03 H'91 H'00 H'62 H'02 010 H'00 H'81 H'2A H'00 H'00 H'00 H'0014.45.28.500 00003 HWSW SIGNAL IDENTY (H'0016) FROM EQU NO 1-0-42-00 TO TLP11 (H'0391) EXE A IN LIM 001
WITH 0 1 2 3 4 5 6 7 8 9 000 H'00 H'62 H'4C H'C7 H'00 H'00 H'00 H'00 H'00 H'00 010 H'00 H'00 H'00 H'00 H'00 H'00 H'00 H'00 H'0014.45.28.500 00004 SWSW SIGNAL BORDIDENTY (H'001E) FROM TLP11 (H'0391) EXE A IN LIM 001 TO DCP (H'007E) EXE A IN LIM 001 WITH 0 1 2 3 4 5 6 7 8 9 000 H'00 H'90 H'00 H'4C H'C7 H'03 H'91 H'00 H'62 H'02 010 H'00 H'81 H'2A H'00 H'00 H'00 H'0014.45.40.820 00005 HWSW SIGNAL IDENTY (H'0016) FROM EQU NO 1-0-42-00 TO TLP11 (H'0391) EXE A IN LIM 001 WITH 0 1 2 3 4 5 6 7 8 9 000 H'00 H'62 H'4C H'C7 H'00 H'00 H'00 H'00 H'00 H'00 010 H'00 H'00 H'00 H'00 H'00 H'00 H'00 H'00 H'0014.45.40.820 00006 SWSW SIGNAL BORDIDENTY (H'001E) FROM TLP11 (H'0391) EXE A IN LIM 001 TO DCP (H'007E) EXE A IN LIM 001 WITH 0 1 2 3 4 5 6 7 8 9 000 H'00 H'90 H'00 H'4C H'C7 H'03 H'91 H'00 H'62 H'02 010 H'00 H'81 H'2A H'00 H'00 H'00 H'0014.45.53.180 00007 HWSW SIGNAL IDENTY (H'0016) FROM EQU NO 1-0-42-00 TO TLP11 (H'0391) EXE A IN LIM 001 WITH 0 1 2 3 4 5 6 7 8 9 000 H'00 H'62 H'4C H'C7 H'00 H'00 H'00 H'00 H'00 H'00 010 H'00 H'00 H'00 H'00 H'00 H'00 H'00 H'00 H'0014.45.53.180 00008 SWSW SIGNAL BORDIDENTY (H'001E) FROM TLP11 (H'0391) EXE A IN LIM 001 TO DCP (H'007E) EXE A IN LIM 001 WITH 0 1 2 3 4 5 6 7 8 9 000 H'00 H'90 H'00 H'4C H'C7 H'03 H'91 H'00 H'62 H'02 010 H'00 H'81 H'2A H'00 H'00 H'00 H'0014.46.05.520 00009 HWSW SIGNAL IDENTY (H'0016) FROM EQU NO 1-0-42-00 TO TLP11 (H'0391) EXE A IN LIM 001 WITH 0 1 2 3 4 5 6 7 8 9 000 H'00 H'62 H'4C H'C7 H'00 H'00 H'00 H'00 H'00 H'00 010 H'00 H'00 H'00 H'00 H'00 H'00 H'00 H'00 H'0014.46.05.520 00010 SWSW SIGNAL BORDIDENTY (H'001E) FROM TLP11 (H'0391) EXE A IN LIM 001 TO DCP (H'007E) EXE A IN LIM 001 WITH 0 1 2 3 4 5 6 7 8 9 000 H'00 H'90 H'00 H'4C H'C7 H'03 H'91 H'00 H'62 H'02 010 H'00 H'81 H'2A H'00 H'00 H'00 H'0014.46.17.880 00011 HWSW SIGNAL IDENTY (H'0016) FROM EQU NO 1-0-42-00 TO TLP11 (H'0391) EXE A IN LIM 001 WITH 0 1 2 3 4 5 6 7 8 9 000 H'00 H'62 H'4C H'C7 H'00 H'00 H'00 H'00 H'00 H'00 010 H'00 H'00 H'00 H'00 H'00 H'00 H'00 H'00 H'0014.46.17.880 00012 SWSW SIGNAL BORDIDENTY (H'001E) FROM TLP11 (H'0391) EXE A IN LIM 001 TO DCP (H'007E) EXE A IN LIM 001 WITH 0 1 2 3 4 5 6 7 8 9
000 H'00 H'90 H'00 H'4C H'C7 H'03 H'91 H'00 H'62 H'02 010 H'00 H'81 H'2A H'00 H'00 H'00 H'0014.46.30.620 00013 HWSW SIGNAL IDENTY (H'0016) FROM EQU NO 1-0-42-00 TO TLP11 (H'0391) EXE A IN LIM 001 WITH 0 1 2 3 4 5 6 7 8 9 000 H'00 H'62 H'4C H'C7 H'00 H'00 H'00 H'00 H'00 H'00 010 H'00 H'00 H'00 H'00 H'00 H'00 H'00 H'00 H'0014.46.30.620 00014 SWSW SIGNAL BORDIDENTY (H'001E) FROM TLP11 (H'0391) EXE A IN LIM 001 TO DCP (H'007E) EXE A IN LIM 001 WITH 0 1 2 3 4 5 6 7 8 9 000 H'00 H'90 H'00 H'4C H'C7 H'03 H'91 H'00 H'62 H'02 010 H'00 H'81 H'2A H'00 H'00 H'00 H'0014.46.43.060 00015 HWSW SIGNAL IDENTY (H'0016) FROM EQU NO 1-0-42-00 TO TLP11 (H'0391) EXE A IN LIM 001 WITH 0 1 2 3 4 5 6 7 8 9 000 H'00 H'62 H'4C H'C7 H'00 H'00 H'00 H'00 H'00 H'00 010 H'00 H'00 H'00 H'00 H'00 H'00 H'00 H'00 H'0014.46.43.060 00016 SWSW SIGNAL BORDIDENTY (H'001E) FROM TLP11 (H'0391) EXE A IN LIM 001 TO DCP (H'007E) EXE A IN LIM 001 WITH 0 1 2 3 4 5 6 7 8 9 000 H'00 H'90 H'00 H'4C H'C7 H'03 H'91 H'00 H'62 H'02 010 H'00 H'81 H'2A H'00 H'00 H'00 H'0014.46.47.640 00017 SWSW SIGNAL CRADRCHECK (H'0035) FROM LCR (H'0070) EXE A IN LIM 001 TO TLP11 (H'0391) EXE A IN LIM 001 WITH 0 1 2 3 4 5 6 7 8 9 000 H'02 H'00 H'48 H'C2 H'02 H'00 H'47 H'BC14.46.47.640 00018 SWSW SIGNAL NRPOINTER (H'001B) FROM TLP11 (H'0391) EXE A IN LIM 001 TO LCR (H'0070) EXE A IN LIM 001 WITH 0 1 2 3 4 5 6 7 8 9 000 H'03 H'91 H'02 H'B5 H'02 H'00 H'96 H'FC H'00 H'00 010 H'00 H'0014.46.47.640 00019 SWSW SIGNAL CRADREXEC (H'0060) FROM TLP11 (H'0391) EXE A IN LIM 001 TO LCR (H'0070) EXE A IN LIM 001 WITH 0 1 2 3 4 5 6 7 8 9 000 H'03 H'91 H'02 H'00 H'B8 H'9E H'02 H'00 H'97 H'4614.46.49.320 00020 SWSW SIGNAL SIZTRU (H'0039) FROM DTR (H'035A) EXE A IN LIM 001 TO TLP11 (H'0391) EXE A IN LIM 001 WITH 0 1 2 3 4 5 6 7 8 9 000 H'00 H'5F H'00 H'00 H'F9 H'03 H'5A H'39 H'7C H'03 010 H'19 H'01 H'10 H'00 H'03 H'00 H'00 H'00 H'00 H'0F 020 H'00 H'00 H'00 H'00 H'01 H'00 H'19 H'00 H'00 H'00 030 H'01 H'FF H'FF H'FF H'FF H'FF H'FF H'FF H'FF H'02 040 H'00 H'02 H'00 H'CC H'78 H'02 H'00 H'5A H'2E14.46.49.320 00021 SWHW SIGNAL LOOPST (H'000A) FROM TLP11 (H'0391) EXE A IN LIM 001 TO EQU NO 1-0-42-06 WITH 0 1 2 3 4 5 6 7 8 9
000 H'02 H'02 H'00 H'6D H'DC H'02 H'00 H'43 H'1014.46.49.320 00022 SWSW SIGNAL SIZTRURES (H'002E) FROM TLP11 (H'0391) EXE A IN LIM 001 TO RMP (H'0319) EXE A IN LIM 001 WITH 0 1 2 3 4 5 6 7 8 9 000 H'39 H'7C H'00 H'00 H'5F H'2A H'03 H'91 H'01 H'00 010 H'F9 H'03 H'5A H'03 H'00 H'01 H'00 H'00 H'02 H'00 020 H'43 H'C2 H'00 H'00 H'00 H'0014.46.49.320 00023 SWSW SIGNAL SENFILCAT (H'0067) FROM RMP (H'0319) EXE A IN LIM 001 TO TLP11 (H'0391) EXE A IN LIM 001 WITH 0 1 2 3 4 5 6 7 8 9 000 H'00 H'5F H'2A H'00 H'00 H'00 H'02 H'08 H'C2 H'6C 010 H'02 H'03 H'38 H'7214.46.49.340 00024 SWSW SIGNAL FETMULPOS (H'002B) FROM SCP (H'032F) EXE A IN LIM 001 TO TLP11 (H'0391) EXE A IN LIM 001 WITH 0 1 2 3 4 5 6 7 8 9 000 H'00 H'5F H'2A H'00 H'02 H'6F H'03 H'2F H'01 H'FF 010 H'02 H'00 H'92 H'8A H'02 H'00 H'3A H'1614.46.49.340 00025 SWSW SIGNAL FETMULPOSRES (H'0042) FROM TLP11 (H'0391) EXE A IN LIM 001 TO SCP (H'032F) EXE A IN LIM 001 WITH 0 1 2 3 4 5 6 7 8 9 000 H'00 H'02 H'6F H'00 H'96 H'02 H'00 H'52 H'68 H'00 010 H'00 H'00 H'0014.46.49.640 00026 SWSW SIGNAL SENNUM (H'010D) FROM RMP (H'0319) EXE A IN LIM 001 TO TLP11 (H'0391) EXE A IN LIM 001 WITH 0 1 2 3 4 5 6 7 8 9 000 H'00 H'5F H'2A H'00 H'FF H'FF H'FF H'FF H'00 H'09 010 H'00 H'FF H'FF H'FF H'00 H'00 H'00 H'02 H'08 H'C3 020 H'8C H'02 H'08 H'47 H'8414.46.49.640 00027 SWSW SIGNAL MINNUMSEN (H'00AE) FROM TLP11 (H'0391) EXE A IN LIM 001 TO RMP (H'0319) EXE A IN LIM 001 WITH 0 1 2 3 4 5 6 7 8 9 000 H'39 H'7C H'02 H'00 H'6F H'4C H'02 H'00 H'4C H'0C14.46.49.880 00028 HWSW SIGNAL LINELEVEL (H'0007) FROM EQU NO 1-0-42-06 TO TLP11 (H'0391) EXE A IN LIM 001 WITH 0 1 2 3 4 5 6 7 8 9 000 H'00 H'5F H'02 H'02 H'00 H'00 H'00 H'00 H'00 H'00 010 H'00 H'0014.46.49.880 00029 SWHW SIGNAL LOOPPE (H'000B) FROM TLP11 (H'0391) EXE A IN LIM 001 TO EQU NO 1-0-42-06 WITH 0 1 2 3 4 5 6 7 8 9 000 H'03 H'02 H'00 H'6D H'C0 H'02 H'00 H'18 H'D414.46.49.940 00030 HWSW SIGNAL LINELEVEL (H'0007) FROM EQU NO 1-0-42-06 TO TLP11 (H'0391) EXE A IN LIM 001 WITH 0 1 2 3 4 5 6 7 8 9 000 H'00 H'5F H'03 H'02 H'00 H'00 H'00 H'00 H'00 H'00 010 H'00 H'00
14.46.50.080 00031 SWSW SIGNAL SENNUM (H'010D) FROM RMP (H'0319) EXE A IN LIM 001 TO TLP11 (H'0391) EXE A IN LIM 001 WITH 0 1 2 3 4 5 6 7 8 9 000 H'00 H'5F H'2A H'00 H'FF H'FF H'FF H'FF H'00 H'05 010 H'00 H'FF H'FF H'FF H'00 H'00 H'00 H'02 H'08 H'C3 020 H'8C H'02 H'08 H'47 H'8414.46.50.480 00032 SWSW SIGNAL SENNUM (H'010D) FROM RMP (H'0319) EXE A IN LIM 001 TO TLP11 (H'0391) EXE A IN LIM 001 WITH 0 1 2 3 4 5 6 7 8 9 000 H'00 H'5F H'2A H'00 H'FF H'FF H'FF H'FF H'00 H'06 010 H'00 H'FF H'FF H'FF H'00 H'00 H'00 H'02 H'08 H'C3 020 H'8C H'02 H'08 H'47 H'8414.46.50.500 00033 SWSW SIGNAL JOBCONTINUE (H'00B9) FROM TLP11 (H'0391) EXE A IN LIM 001 TO TLP11 (H'0391) EXE A IN LIM 001 WITH 0 1 2 3 4 5 6 7 8 9 000 H'00 H'5F H'00 H'07 H'02 H'00 H'6D H'5C H'02 H'00 010 H'78 H'A414.46.50.500 00034 SWSW SIGNAL CONKS (H'0048) FROM TLP11 (H'0391) EXE A IN LIM 001 TO TSP (H'033B) EXE A IN LIM 001 WITH 0 1 2 3 4 5 6 7 8 9 000 H'03 H'91 H'00 H'5F H'2A H'00 H'96 H'01 H'02 H'00 010 H'65 H'9A H'02 H'00 H'5F H'7E14.46.50.520 00035 SWSW SIGNAL KSCON (H'0087) FROM TSP (H'033B) EXE A IN LIM 001 TO TLP11 (H'0391) EXE A IN LIM 001 WITH 0 1 2 3 4 5 6 7 8 9 000 H'00 H'5F H'2A H'9F H'70 H'03 H'3B H'02 H'00 H'55 010 H'D6 H'02 H'00 H'2E H'7614.46.50.520 00036 SWSW SIGNAL SENKEYDIG (H'0028) FROM TLP11 (H'0391) EXE A IN LIM 001 TO TSP (H'033B) EXE A IN LIM 001 WITH 0 1 2 3 4 5 6 7 8 9 000 H'9F H'70 H'09 H'50 H'02 H'00 H'6A H'12 H'02 H'00 010 H'09 H'2214.46.50.720 00037 SWSW SIGNAL KEYDIGSEN (H'0029) FROM ADP (H'028C) EXE A IN LIM 001 TO TLP11 (H'0391) EXE A IN LIM 001 WITH 0 1 2 3 4 5 6 7 8 9 000 H'00 H'5F H'2A H'02 H'00 H'14 H'C6 H'00 H'00 H'00 010 H'0014.46.50.720 00038 SWSW SIGNAL SENKEYDIG (H'0028) FROM TLP11 (H'0391) EXE A IN LIM 001 TO TSP (H'033B) EXE A IN LIM 001 WITH 0 1 2 3 4 5 6 7 8 9 000 H'9F H'70 H'05 H'50 H'02 H'00 H'6A H'12 H'02 H'00 010 H'24 H'F614.46.50.900 00039 SWSW SIGNAL SENNUM (H'010D) FROM RMP (H'0319) EXE A IN LIM 001 TO TLP11 (H'0391) EXE A IN LIM 001 WITH 0 1 2 3 4 5 6 7 8 9 000 H'00 H'5F H'2A H'00 H'FF H'FF H'FF H'FF H'00 H'00
010 H'00 H'FF H'FF H'FF H'00 H'00 H'00 H'02 H'08 H'C3 020 H'8C H'02 H'08 H'47 H'8414.46.50.940 00040 SWSW SIGNAL KEYDIGSEN (H'0029) FROM ADP (H'028C) EXE A IN LIM 001 TO TLP11 (H'0391) EXE A IN LIM 001 WITH 0 1 2 3 4 5 6 7 8 9 000 H'00 H'5F H'2A H'02 H'00 H'14 H'C6 H'00 H'00 H'00 010 H'0014.46.50.940 00041 SWSW SIGNAL SENKEYDIG (H'0028) FROM TLP11 (H'0391) EXE A IN LIM 001 TO TSP (H'033B) EXE A IN LIM 001 WITH 0 1 2 3 4 5 6 7 8 9 000 H'9F H'70 H'06 H'50 H'02 H'00 H'6A H'12 H'02 H'00 010 H'24 H'F614.46.51.140 00042 SWSW SIGNAL KEYDIGSEN (H'0029) FROM ADP (H'028C) EXE A IN LIM 001 TO TLP11 (H'0391) EXE A IN LIM 001 WITH 0 1 2 3 4 5 6 7 8 9 000 H'00 H'5F H'2A H'02 H'00 H'14 H'C6 H'00 H'00 H'00 010 H'0014.46.51.140 00043 SWSW SIGNAL SENKEYDIG (H'0028) FROM TLP11 (H'0391) EXE A IN LIM 001 TO TSP (H'033B) EXE A IN LIM 001 WITH 0 1 2 3 4 5 6 7 8 9 000 H'9F H'70 H'00 H'50 H'02 H'00 H'6A H'12 H'02 H'00 010 H'24 H'F614.46.51.200 00044 SWSW SIGNAL SENNUM (H'010D) FROM RMP (H'0319) EXE A IN LIM 001 TO TLP11 (H'0391) EXE A IN LIM 001 WITH 0 1 2 3 4 5 6 7 8 9 000 H'00 H'5F H'2A H'00 H'FF H'FF H'FF H'FF H'00 H'00 010 H'00 H'FF H'FF H'FF H'00 H'00 H'00 H'02 H'08 H'C3 020 H'8C H'02 H'08 H'47 H'8414.46.51.360 00045 SWSW SIGNAL KEYDIGSEN (H'0029) FROM ADP (H'028C) EXE A IN LIM 001 TO TLP11 (H'0391) EXE A IN LIM 001 WITH 0 1 2 3 4 5 6 7 8 9 000 H'00 H'5F H'2A H'02 H'00 H'14 H'C6 H'00 H'00 H'00 010 H'0014.46.51.360 00046 SWSW SIGNAL SENKEYDIG (H'0028) FROM TLP11 (H'0391) EXE A IN LIM 001 TO TSP (H'033B) EXE A IN LIM 001 WITH 0 1 2 3 4 5 6 7 8 9 000 H'9F H'70 H'00 H'50 H'02 H'00 H'6A H'12 H'02 H'00 010 H'24 H'F614.46.51.560 00047 SWSW SIGNAL KEYDIGSEN (H'0029) FROM ADP (H'028C) EXE A IN LIM 001 TO TLP11 (H'0391) EXE A IN LIM 001 WITH 0 1 2 3 4 5 6 7 8 9 000 H'00 H'5F H'2A H'02 H'00 H'14 H'C6 H'00 H'00 H'00 010 H'0014.46.51.580 00048 SWSW SIGNAL DISAUXDEV (H'0046) FROM TLP11 (H'0391) EXE A IN LIM 001 TO TSP (H'033B) EXE A IN LIM 001 WITH 0 1 2 3 4 5 6 7 8 9
000 H'00 H'9F H'70 H'02 H'00 H'6A H'FC H'02 H'00 H'60 010 H'5A14.46.55.680 00049 HWSW SIGNAL IDENTY (H'0016) FROM EQU NO 1-0-42-00 TO TLP11 (H'0391) EXE A IN LIM 001 WITH 0 1 2 3 4 5 6 7 8 9 000 H'00 H'62 H'4C H'C7 H'00 H'00 H'00 H'00 H'00 H'00 010 H'00 H'00 H'00 H'00 H'00 H'00 H'00 H'00 H'0014.46.55.700 00050 SWSW SIGNAL BORDIDENTY (H'001E) FROM TLP11 (H'0391) EXE A IN LIM 001 TO DCP (H'007E) EXE A IN LIM 001 WITH 0 1 2 3 4 5 6 7 8 9 000 H'00 H'90 H'00 H'4C H'C7 H'03 H'91 H'00 H'62 H'02 010 H'00 H'81 H'2A H'00 H'00 H'00 H'0014.46.56.500 00051 SWSW SIGNAL EOSMES (H'0046) FROM TLP11 (H'0391) EXE A IN LIM 001 TO RMP (H'0319) EXE A IN LIM 001 WITH 0 1 2 3 4 5 6 7 8 9 000 H'39 H'7C H'03 H'FF H'01 H'00 H'02 H'00 H'6C H'D4 010 H'02 H'00 H'78 H'EC14.46.56.520 00052 SWSW SIGNAL RELINK &
himdp (TechnicalUser) 15 Sep 08 7:19 I assume that the external caller is called and answers but is diconnected after 2 Minutes. If this is the case then D7 of VARO should be '0' i.e VARO should be set to 00002805.Give it a try
b17liviu (TechnicalUser) 15 Sep 08 8:02
HI
I try , but my route dial with only VARO D7=4,D7=C.
himdp (TechnicalUser) 15 Sep 08 8:48 the call is cleared after 2 minutes by CMP, this means that the MD110 is clearing the call. You have confirmed this by changing PARNUM 41. The 2 minute timeout is waiting for B-Answer. If this is not expected then no timeout will occur. With D7=4, you are set for no clear signal from line, no PTS signal from line but B-answer expected from line. The equivelent to this for no B-Answer expected is D7=0.
To dial out, 0, 4, 8 and C should work however 4, 8 and C will be expecting B-Answer and if none is received will time out and clear (as you see)
If 0 does not work, as you say, then I have no more ideas.
fcpli (TechnicalUser) 16 Sep 08 8:04 The timeout comes from CMP routine TRURINTIMSUP, meaning that the timer supervises the ringing time. I checked this in the lab with your parameters, and with D7=4 the problem is there. But with value "1" it works fine. What you need to do, is to confirm that the MD really is not dialling towards the line when D4 /= 4. If you trace it, you'll most probably see that the digits are sent. What you can do is to listen to the line when sending DTMF. What happens? We can always remove the ringtime supervision from outgoing TLP11, but this is not the correct way...Note that the B-answer is a polarity reversal, and this is expected according the parameter in VARO. The ASPAC valueaffects the whole switch.
If you want, change the value D7 to e.g. 1, start the trace, dial some number, and post that one here, if you are not sure that the system sends the digits from/to RMP, TLP11, TSP, ADP.
b17liviu (TechnicalUser) 17 Sep 08 3:15 The P.B.X. is from long distance and the test i make with my opeator. When i setting D7=0, he said that route don't working. I checking again and my route dial with D7=0. Sorry for my confusion. Thank you for all.
Operator Diversionthread806-1492835Share This Forum Search FAQs Links Jobs Whitepapers MVPs
grinchstyle (TechnicalUser) 8 Aug 08 9:44 Hi Guys,
I've been trying over the last couple days to get my absent operator to divert but still no success. PELPI, CDINI commands dont work and OPADC. Any suggestion guys? I dont think a *21*ext# works either...
Thanks
whosrdaddy (Vendor) 8 Aug 08 10:06 show some commands:
NADAP:NUMTYP=OI&OD&OC;OPDDP:DIR=ALL;OPCTP:CORG=ALL; ----------------------------------------------------- What You See Is What You GetNever underestimate tha powah of tha google!
Satellite1900 (TechnicalUser) 8 Aug 08 10:07
Hello,Do you entered the command RODNI on incoming rou and also on internal calls?
grinchstyle (TechnicalUser) 8 Aug 08 10:12 Here's the output of the commands.
<∟NADAP:NUMTYP=OI&OD&OC; NUMBER ANALYSIS DATA
TYPE OF SERIES NUMBER SERIES
OPERATOR INDIV. NUMBER SERIES 200
OPERATOR COMMON NUMBER SERIES 0
OPERATOR COM. DID. NUM. SERIES 1000
END
<∟OPDDP:DIR=ALL; OPERATOR DIRECTORY DATA
DIR EQU OCUST TYPE PCM REV 200 001-0-30-00 1 6 - -
END
<∟OPCTP:CORG=ALL; NOT ACCEPTEDCORGNOT ASSIGNED
Thanks!
Satellite1900 (TechnicalUser) 8 Aug 08 10:39 You need to configure the corg with its calt for all types of calls, then entering the command opadc for service night.For incoming calls also rodni.
Satellite1900 (TechnicalUser) 8 Aug 08 15:36 Follow this configuration:OPCTS:CORG=1,CALT=1,OACC=0;OPCTS:CORG=2,CALT=2,OACC=0;OPCTS:CORG=3,CALT=3,OACC=0;OPCTS:CORG=7,CALT=7,OACC=1000,ROU=(INCOMING ROU);OPCGS:CORG=1,DIR=200,CHO=1;OPCGS:CORG=2,DIR=200,CHO=1;OPCGS:CORG=3,DIR=200,CHO=1;OPCGS:CORG=7,DIR=200,CHO=1;OPADC:CORG=1,NDIR=Y,RERNUM=(NUMBER OF NIGHT SERVICE);OPADC:CORG=2,NDIR=Y,RERNUM=(NUMBER OF NIGHT SERVICE);OPADC:CORG=3,NDIR=Y,RERNUM=(NUMBER OF NIGHT SERVICE);OPADC:CORG=7,NDIR=Y,RERNUM=(NUMBER OF NIGHT SERVICE);RODNI:ROU=(INCOMING ROU),NIG=(NUMBER OF NIGHT SERVICE);
This configuration is for all types of calls.The night service is configured for both internal calls both for those entrants.Try it and good luck
grinchstyle (TechnicalUser) 9 Aug 08 11:30 Thanks a bunch! I'll try this out and let you know how it works..
Hitechbuzz (TechnicalUser) 18 Aug 08 18:10 Hi grinchstyle I did not see if you got this sorted I use *24*(hunt group that calls are going to)eg8128*(phone thats are to terminate on)eg.8989# So the commaned is *24*8128*8989#then when I wish to restore it the command is #24*8128# This means that the operator can use a master phone if She loses the consul hope this helpscheers Brian Cheers BrianTo see is to know To Know is to see
Huntingthread806-1491559
Share This
Forum Search FAQs Links Jobs Whitepapers MVPs
jaylek (TechnicalUser)
3 Aug 08 15:41
Hai,
I need some help to the following scenareo...I have 7 digital extensions and 2 dect phones. I need to programme these as hunting. digital extensions are 501,502,522,530,532...Dect extensions are 545,546....My hunt group number is 500.<GHDAP:GRP=500;GROUP HUNTING DATA GRP LIM SERV TRAF SEL QUE CUST RLTC DIR 500 1 11010 15 010001 10 0 501 502 522 530 532
I need to work in this way.External Call reaches 500 Then it should ring to first member 501, if not answer/busy it should deflect to 502 and if 502 no answer/bsy it shoul ring to dect 545,and if 545 no answer/bsy it should deflect to 530 etc ......
Will it work???
Another one request is if a call lands on 500 it reaches 1st member (501)and 501 is busy whether there is an option to divert to 501 again if it is free????
<ROCAP:ROU=ALL;ROUTE CATEGORY DATAROU SEL TRM SERV NODG DIST DISL TRAF SIG BCAP10 7130000000000010 5 0100000001 0 30 128 00151514 211100010031 111111<RODAP:ROU=ALL;ROUTE DATAROU TYPE VARC VARI VARO FILTER 10 SL60 H'00000110 H'15400000 H'06110000 NO<GESPP:CSP=ALL;COMMON SERVICE PROFILECSP TRAF SERV CDIV ROC NPRES
0 0103151515 2051101011300 00013213 402401 00101 0113010115 2051101111300 11513103 402401 00102 1103151515 2051101011300 00013213 402401 00103 0103040415 2051101011300 11210103 402401 00104 1103151515 0000000010200 00700003 000001 00108 0103020215 2051101011300 00013213 402401 0010
<EXCCP:CAT=1&&12;EXTENSION CATEGORY CODE CAT TRAF SERV CDIV ROC 1 00010115 0215120700 000120000 0000012 00020215 0215130700 010151311 0000013 00151515 0215130700 010151311 0000014 00040415 0215130700 010151311 0000015 00050515 0215130700 010151311 0000016 00060615 0200120700 010151311 0000017 00000000 0000000000 000000000 0000018 00030315 0215130700 000120000 0001119 00090915 0215130700 000120000 00000110 00101015 0215120700 000120000 00000111 00060615 0215130700 010151311 00000112 03060615 0215130700 010151311 000001
Finally can we mix digital extensions and dect phones in the hunt group??
Thanks in advance
drewMk2 (TechnicalUser) 4 Aug 08 3:59
First qestion everyone will ask you is what version your system is.....you should always post this as well it give you quicker responses
"There is no place like 127.0.0.1"
jaylek (TechnicalUser) 4 Aug 08 6:16
Hai
Sorry for that.
MX ONE VERSION: CXP1010101/4/TSWSP04/R5A
It was BC12 upgraded to MX-ONE.
whosrdaddy (Vendor) 4 Aug 08 6:55
Rule #1 on MD110:
don't use no anwser diversions in a GH.
the functionality that you describe can perfectly be done with a personal number (PELPI)
make a GEDII as pilot number and put the PELPI on that...
the only limitation is that you have 10 positons...
/Daddy
----------------------------------------------------- What You See Is What You GetNever underestimate tha powah of tha google!
jaylek (TechnicalUser) 4 Aug 08 8:10
You mean to say a mix of digital and dect possible with PELPI???
whosrdaddy (Vendor) 4 Aug 08 12:04
yes offcourse.
Alex says:
Quote:
DIR =D 1 D 2 D 3 D 4 D 5 D 1 D 2 D 3 D 4 D 5 = 00-99 999 Directory number corresponding to a Personal Number that can be: - An analogue extension - A digital extension - A digital POTS - An ISDN terminal - A CAS extension - An integrated cordless extension - An IP extension - A remote extension (mobile and fixed remote extension)
/Daddy
----------------------------------------------------- What You See Is What You GetNever underestimate tha powah of tha google!
Voip on Md110thread806-1489378Share This Forum Search FAQs Links Jobs Whitepapers MVPs
Chamvari (Vendor) 24 Jul 08 6:05 we have recently taken over maintenance of md110 pbx. The client wans to go Voip linked to a Lg IPldk and the other site has a patton Voip gateway. What is the requirement for the md110 to go Ip .
LeeMason (MIS) 29 Jul 08 3:27 You will probably need to be on at least BC12 (I think - possibly BC13). You will need an ELU32 (or more dependent on your requirements) in the system to provide IP connectivity.
I'm not sure about the Patton gateway. Is this H.323 or SIP?
I know that the MX-ONE can do SIP trunking and think that the MD-110 can also do this but I'm not sure. I know that the MD-110 can have SIP extensions so I guess trunking is possible. Lee MasonOptimal Projects Ltdwww.opl.co.ukwww.backupsanywhere.com
doktor (IS/IT--Management) 29 Jul 08 3:49 Hi Petros
We tried years ago to interconnect an MD100 BC12 and ipLDK-100 version 3.0, but gave up as there were problems with CODEC negotiations (G.711, G723). The call setup failed due to these problems.Maybe these problems are solved now?///doktor
Chamvari (Vendor) 29 Jul 08 7:50 Patton you can have on with both sip & h.323.
RODDI = no free spacethread806-1488405Share This Forum Search FAQs Links Jobs Whitepapers MVPs
cablejerk (TechnicalUser) 19 Jul 08 21:36 Hello All I have a problem iniating new ED's, can anyone help me find the cause of this problem? Here is a printout
<RODDI:DEST=6388,ROU=53;NOT ACCEPTED NO FREE SPACE<ALLOP;ALARM LOGIDENTITY: XXXXX-BC90REVB
VERSION: LZY2035106/1/53-CNI85-000003FF/R1A
DATE: 20JUL08 TIME: 10:37:08CLASS: 1320 HIGH CALL RATEDATE TIME ALP NOIF UNIT EQU INF1 INF2 18JUL08 16:44:01 2 34 RMPS2 005-*-**-** 0 14
CLASS: 0113 FAILURE TO SEIZE AN I/O PORT BY COMMAND HIADPDATE TIME ALP NOIF UNIT EQU 18JUL08 15:41:58 1 1 001-*-**-**RDATE RTIME 18JUL08 15:43:18
END<FISCP:IODEV=SYSDISK1; FILE SYSTEM CAPACITY DATATOTAL DISK SPACE: 2067 MBYTESSUBFS: SYSSUBFS11KBYTES FILESTOTAL AVAIL TOTAL MOUNTED64512 47213 19200 /SYSN/USR1 SUBFS: SYSSUBFS21KBYTES FILESTOTAL AVAIL TOTAL MOUNTED64512 47504 19200 /SYSN/USR2 END <IODDP;I/O DEVICE DATANODE IODEV/SUBFS EQU/BPOS SIPOS VEND/USAGE STATUSSYSN - 001-0-23 - - IN SERVICE SYSN SYSDISK1 001-0-23-0 3 ADTX IN SERVICE SYSSUBFS11 SYSSUBFS21SYSN SYSTERMINAL 001-0-23-1 - MML - SYSN SYSTERM2 001-0-23-2 - MML - SYSN SYSTERM3 001-0-23-3 - MML - LIM5 - 005-0-41 - - IN SERVICE LIM5 SYSTEMINAL3 005-0-41-1 - MML - LIM5 SYSTEMINAL4 005-0-41-2 - MML - LIM5 SYSTEMINAL5 005-0-41-3 - MML - END <FIOFP:NODE=SYSN;NOT ACCEPTEDOPEN FILES NOT FOUND <FIOFP:NODE=LIM5;NOT ACCEPTEDOPEN FILES NOT FOUND <CADAP;CALENDAR DATA
IDENTITY=XXXXX-BC90REVBVERSION=LZY2035106/1/53-CNI85-000003FF/R1A10:46:04SUN 20 JUL 2008END Thanks in advanceCablejerk
whosrdaddy (Vendor) 20 Jul 08 14:32 how many entries do you have in roddp:dest=all; ? ----------------------------------------------------- What You See Is What You GetNever underestimate tha powah of tha google!
cablejerk (TechnicalUser) 20 Jul 08 15:27 Hello Daddy, not on site at the moment but there would be around 300 ED's programmed,some of them in ranges of up to 500 numbers some individual, is there a limit?
cablejerk (TechnicalUser) 20 Jul 08 17:53 Should have waited, RODDP:DEST=ALL results in 499 entries.
cablejerk (TechnicalUser) 20 Jul 08 20:03 Alex answers the question
"Route Choice Table Maximum 500 route choices to be shared by LCR, PNR, CUST and Automatic Alternative Routing. One table can contain maximum 8 route choices. "
The question now is, can this be changed?
cablejerk (TechnicalUser) 21 Jul 08 4:12 QED, some lateral thinking reduced the ED route table to 30 entries. Thanks All
ISDN Release problemthread806-1472635Share This Forum Search FAQs Links Jobs Whitepapers MVPs
Find A Job or Post a Job Opening Click Here.cpux10 (TechnicalUser) 12 May 08 5:23 Hi,
I am experiencing this problem on both TSW SP3 and BC12 SP11 systems:
An external caller calls my MD110/MX-ONE system using ISDN PRI lines, the call is routed through an ISDN QSIG line to an external Call Center system (so I have an SL60-SL60 connection). After the call is disconnected, the trunk individuals involved in this connection are not released until after 40 seconds.
This is causing me some trouble during high traffic. Any ideas or suggestions to decrease this release time?
ceejay55 (TechnicalUser) 12 May 08 18:59
We have to set VARC D3=1 on public ISDN otherwise call will hold up for 30 secs to a digital phone(unless of course the B party hangs up first)This is for Support of Inband tones
cpux10 (TechnicalUser) 14 Jul 08 0:24 Tried setting VARC D3=1, but the problem is still there.
Any other ideas?
Auth Codesthread806-1484726Share This Forum Search FAQs Links Jobs Whitepapers MVPs
Check Out Our Whitepaper Library. Click Here.tczmbara (MIS) 3 Jul 08 7:28 Hi All,Im trying to initiate auth code on extension 7320
typing command:auth_code_init -dir 7320 -cat 10 -restrict -code 2731 -cil 7320 -customer 0
trying to initiate a phone call, using code *72*auth_code#, im gettin Wrong Auth Code
What Im doing wrong
please advise Best Regardstczmbara
mbtoma (TechnicalUser) 4 Jul 08 6:55 Hi tczmbara,I guess the FC is wrong, i.e. you defined a individual (regional) authorization code, so you should try *75* (dialling) or *76* (blocking). Give it a try.Toma
tczmbara (MIS) 7 Jul 08 8:46 Hiim able to block extension using code *76*code#
but im not able to make a call (using *75*code#number) Best Regardstczmbara
Group call pick upthread806-1482863Share This
Forum Search FAQs Links Jobs Whitepapers MVPsFind A Job or Post a Job Opening Click Here.
jaylek (TechnicalUser) 25 Jun 08 8:49
Is there any limitation on the IP extensions for using Group call pick up? Or is there any additional set up?
Regards,
rfpup (TechnicalUser) 25 Jun 08 9:00 No limitation, normal behavior as digital phones
jaylek (TechnicalUser) 25 Jun 08 12:04 Rfpup,
I created a group with 2 members and tried but getting like vacant number. What could be the issue?
GPGRI & GHGMI both executed.
I beleive the group pick up code is "8".
Any help. I am not at site to give u a print out.
Regards,
mundus (TechnicalUser) 25 Jun 08 12:18 Maybe it's the config file, for example:
[SuffixServices] Intrusion=4 Callwaiting=5 CallBack=6 CallPickup=8
jaylek (TechnicalUser) 25 Jun 08 14:29 Let me check. Thanks for the info.I will come back to uRegards
jaylek (TechnicalUser) 29 Jun 08 1:23 Mundus,
[STOREPHONEBOOKS]EnableStoring=NO
[SuffixServices]Intrusion=8CallWaiting=4CallBack=5CallPickUp=6Conference=3
Actually call pick up is ok. But group call pick not working.Any hint?
mundus (TechnicalUser) 30 Jun 08 14:17 Do you only have this problems ( group call pick-up ) from IP extension ?And what digit are using to group call pick-up - 8 ?
jaylek (TechnicalUser) 30 Jun 08 14:29 Mundus,
Yes I am trying 8. It says vacant number. FYI, I tried 6 also. The individual call pick up is working fine. Kindly look into this.
Regards,
whosrdaddy (Vendor) 30 Jun 08 16:22 please post NADAP; ----------------------------------------------------- What You See Is What You GetNever underestimate tha powah of tha google!
jaylek (TechnicalUser) 4 Jul 08 11:44 Dear whosrdaddy,
Done man. There was a problem in NADAP.
Many thanks.Bye.
rfpup (TechnicalUser) 7 Jul 08 5:54 Hi jaylek!
What was the problem?
Thanks
jaylek (TechnicalUser) 7 Jul 08 6:19 You need to add the service code in NANSI Please check this command NASCS!!!!!!!
Ip phones---don't connect to analog/digitalthread806-1482807Share This Forum Search FAQs Links Jobs Whitepapers MVPs
Check Out Our Whitepaper Library. Click Here.robra (TechnicalUser) 25 Jun 08 4:34 Hi all,
I have a big problem and i can't manage to solve it so if anyone can help me it will mean a lot, so let me tell you my configuration, i have an md110 BC13, with an IPLU card, a ESU, a ELU34 and ELU33, i managed to create the IP Phones and i can call from one to another, and also i created digital and analog ones, which are working together, but i can't call from an IP phone to a digital/analog one, it gives me an error on the IP phone congestion.......so please can you tell me if i should put a command or something else is the problem?????
Thanks a lot
TeleLion (TechnicalUser) 27 Jun 08 0:18 Calling from IP to TDM needs RTP resources check yoyr resources are available, and check your codecs, between phone and gateway. TELEC3
robra (TechnicalUser) 1 Jul 08 5:21 Thanks a lot, finally i succeeded in making the calls, it was my mistake that i didn't put an IP to the IPLU board, and also after checking the rtp and i saw there were ok, i made the call and it worked :). Thanks for your support.
NUTRIthread806-1482734Share This Forum Search FAQs Links Jobs Whitepapers MVPs
Check Out Our Whitepaper Library. Click Here.642234 (TechnicalUser) 24 Jun 08 17:35
Dear all,
I have E-1 link with mobile compnay and receiving digit 113 on that route and 113 is forwarded to hunp group 2300. In MD 110 i want to remove digit 113 after receiving this number on hunt group. I have BC12 SP7 version.Please send me nutri command how i can remove receiving digit 113. Bcoz 2300 is voice mail and when i dail 113 from mobile number it coming (extension 113 does not answer) after this my voice mail greeting start and then after greeting call went through.Bocz this incoming route is forwarded to voice mail.Plz help
642234 (TechnicalUser) 26 Jun 08 14:38 Dear All,
Please help me. using BC12SP7. receiving digit 113 on incoming route. I want to convert113 in to 2300. Please advise.Thanks
dstrang1 (TechnicalUser) 26 Jun 08 22:57 NUTRI:ENTRY=113,CNVTYP=0,NUMTYP=?,TRC=3,PRE=2300;
The ? for numtyp is because you have to know how the digits 113 are formatted. You could start with NUMTYP=0 (0 is unknown type of number) but you may have to play around with it.
Good luck,
Dave Strang
642234 (TechnicalUser) 27 Jun 08 9:56
Dear Dstrang1
Thanks a lot it is woking.Best Regards
T1 in Republic dominicanthread806-1482808Share This Forum Search FAQs Links Jobs Whitepapers MVPs
DEIVIDOS (TechnicalUser) 25 Jun 08 4:38 Hi,
The next week I'm going to install a MX-ONE in Dominican Republic, and I never have programed a T1 route, Somebody can help me with parameters of a T1 route?
ROCAI and RODAI
In a MX-ONE 3.1 with TLU76/11
Thanks
pcasi (TechnicalUser) 26 Jun 08 17:42 TLU76/11 is for E1 links, you´ll need TLU77/11 for T1 to work, otherwise you will have to use a E1-T1 converter.
Regards,pcasi
BPOS Assignment 1-0-30thread806-1482869Share This Forum Search FAQs Links Jobs Whitepapers MVPs
Tek-Tips Forums is Member Supported. Click Here to donate.Monrovia (TechnicalUser) 25 Jun 08 9:06 hi everybody
I am bit confused in this matter
i have one bpos 1-0-30 free. actually i was in a thought that i will use this bpos for ELU29. so i inserted one elu29 and assigned extensions on it. But later on I have decided to go for ELU28. but after removing the elu29, the slot still remain for elu29, even after giving CNHUI command, restarting the lim, on off the lim (reload & restart), the bpos still remain for elu29DEVICE BOARDS NUMBER OF BPOS BOARDID INDIVIDUALS SERVICE STATE
001-0-00 57 32 PASSIVE 001-0-10 102 32 ACTIVE 001-0-20 116 16 ACTIVE 001-0-22 77 16 ACTIVE 001-0-30 87 16 PASSIVE 001-0-32 87 16 PASSIVE
I have not configured 1-0-32(elu29) too. but it is ok, i am going for elu29.
so when i insert the elu28, and CNHUI:BPOS=1-0-30; it is giving like system blocked
DEVICE BOARDS NUMBER OF BPOS BOARDID INDIVIDUALS SERVICE STATE 001-0-00 57 32 PASSIVE 001-0-10 102 32 ACTIVE 001-0-20 116 16 ACTIVE 001-0-22 77 16 ACTIVE 001-0-30 87 16 SYSTEM BLOCKED 001-0-32 87 16 PASSIVE
what could be the reason, that the system is not taking the hardware change?
dstrang1 (TechnicalUser) 25 Jun 08 9:26
Send CNBOE:BPOS=1-0-30; then you should be able to add the new board with CNHUI.
Good luck,
Dave Strang
Monrovia (TechnicalUser) 25 Jun 08 9:34 oh my god! since morning i am trying relod restart,etc etc
thanks dstrang
tomorrow morning let me do this
incoming number to ED to external numberthread806-1481057
Share This
Forum Search FAQs Links Jobs Whitepapers MVPs
DevPlan (TechnicalUser)
17 Jun 08 17:02
I have BC10 and use the numtyp ED to have incoming calls routing over a DIGIUM E1 card that sits in an asterisk box
and then routing the calls to another building to an asterisk server which works fine.
However - due to the problem of receiving and sending fax over voip, I have been asked to forward specific incoming numbers to new POTS numbers to where the fax machines have been connected to.
When I used the following command, calls from internal to 3286 forward correctly to the fax nbr, but when I dial the full number 12343286, I get a voice that this function isn't implemented:
CODEroddi:dest=3286,adc=0225000000000250002,rou=1,pre=328645678910,trc=4,srt=5;
My rondp for route 1 shows:
CODE<rondp:rou=all;ROUTE NUMBER DATAROU PRE ROUDIR EXNOPU EXNOPR TERAC1 2-1234
(3286, 1234 and 45678910 are made-up samples)What would I need to change in order to make the rerouting work when dialed externally?
rgds, devplan
mundus (TechnicalUser) 18 Jun 08 11:20
Hi'
"but when I dial the full number 12343286, I get a voice that this function isn't implemented:"
Some is missing, your dest is 3286 - but you dial 1234... ?
dstrang1 (TechnicalUser) 18 Jun 08 11:59
Create a dest code that is the same as the extension # for the FAX. Then use NUTRI to create an entry to translate the external DID number you wish to use to the dest code (for the dest code set SRT=1 and no entry for PRE or TRC).
With your first RODDI you are sending 89103286 to the asterisk box.
If you have trouble with the NUTRI entry, print out the entry for one of your existing direct dial numbers that go to the asterisk.
Good luck,
Dave Strang
DevPlan (TechnicalUser) 18 Jun 08 14:04
Thanks for the replies.
Probably I wasn't clear about my setup.
We have two LIMs that can call each other internally (like 82xx) and each extension can be called with an outside prefix of 1234 - thus the external complete number to reach ext. 3200 would be 1234 3200.
The extension series 32xx used to be set earlier at one of the LIMs. As the offices with 32xx moved to a different location, I changed the 32xx from EX to ED and setup for each old extension of the 32xx a dest. What was probably not clear from my earlier posting is that I route those 32xx dest out on route 8 (which connects locally to an asterisk box.) Like this:
CODE<roddp:dest=3286;EXTERNAL DESTINATION ROUTE DATADEST DRN ROU CHO CUST ADC TRC SRT NUMACK PRE3286 8 0005000000000250000 4 5 0 32863286
END
The above sample routed correctly the calls (whether internal or external) to the correct asterisk extension.
Now - in order to route the incoming 3286 to 45678910 (new external POTS fax nbr), I tried to simply change route 8 to 1 (route 1 is used for inbound calls and national outbound calls over ISDN30) and to re-route the arriving calls at 3286 to the 45678910 nbr.
It worked when dialing "internally" 3286 - but not from outside 1234 3286.
I hope it's more clear. - and opens a door to a handling. (maybe my pre, trc or srt in roddi is incorrect.)
rgds, devplan
dstrang1 (TechnicalUser) 18 Jun 08 14:25
If I understand correctly, external calls to the FAX will come IN to your MD on Rou=1 and need to be sent OUT to the asterisk on rou=8. You need to create an NUTRI entry for the digits you will receive on rou=1 for external fax calls.
If an external FAX call results in digits 12343286 being received by the MD, and the asterisk needs to be sent 3286, then your NUTRI entry would be: NUTRI:ENTRY=12343286, TRC=4,CNVTYP=0,NUMTYP=x;
And your RODDI would be: (based on vlues above)RODDI:DEST=3286,ROU=8,ADC=0005000000000250000,SRT=1;
Your entry above has you adding 8 digits, truncating 4 and ignoring the next 4.
Hope this helps,
Good Luck,
Dave Strang
DevPlan (TechnicalUser) 18 Jun 08 14:54
Hi dstrang1
Quote:If I understand correctly, external calls to the FAX will come IN to your MD on Rou=1 and need to be sent OUT to the asterisk on rou=8. You need to create an NUTRI entry for the digits you will receive on rou=1 for external fax calls.
Actually like that:
External calls to the FAX come in on my MD on route 1 and needs to go out again on route 1 (as the new FAX nbr 89103286).
Not out on route 8, which it has been previously, that routes to my asterisk box.
rgds, devplan
dstrang1 (TechnicalUser) 18 Jun 08 23:06
OK,
Let's try to simplify this.......your fictitious examples are confusing things.
What would an internal extension on the MD dial if it wanted to call the new external FAX machine?
Whatever that number is, that's what you need to translate the received digits (when an EXTERNAL party calls the FAX)to.
If you want to provide actual numbers along with a print of a dest code or LCR entry for an outbound call for ROU=1, I'm sure we can get your FAX calls routed correctly.
Good luck,
Dave Strang
TLU76/3 configuration
thread806-1480545Share This Forum Search FAQs Links Jobs Whitepapers MVPs
Tek-Tips Forums is Member Supported. Click Here to donate.emags (TechnicalUser) 16 Jun 08 3:56 Hi,
I'm trying to connect 2LIMS by TLU76/3 through Ericsson Mini-Link. This is how i stsrted This is how i started1. <cnhuI:bpos=1-2-60;ORDERED CONFIGURATION HARDWARE UPDATE LIM 001 NEW BOARD FOUND END
CONFIGURATION HARDWARE UPDATE EXECUTED 2. CNLIP:LIM=1,DEV=YES;
LIM CONFIGURATION LIM NUMBER 1 LIM CONTROL LIM CONTROL NUMBER OF SERVICE SYSTEM SIDE SYSTEM STATE PCM-LINKS STATE LIM A EXECUTING 2 ACTIVE B NOT EQUIPPED MEMORY MEMORY MEMORY SPARE VOLUME SPARE AFTER PACKING 65535 KB 14200 KB 14200 KB BUAR1 3435 KB BUAR2 2646 KB INTER LIM SIGNAL PACKET LENGTH CAPABILITY BPOS CAPABILITY 001-0-00 90 001-1-00 90
DEVICE BOARDS NUMBER OF BPOS BOARDID INDIVIDUALS SERVICE STATE 001-0-00 36 32 ACTIVE 001-0-10 78 32 ACTIVE 001-2-60 27 32 PASSIVE 3. <ROCAI:ROU=6,SEL=7110000000000010,SIG=211100100031,TRAF=00151515,TRM=7,SERV=3010000011;EXECUTED 4. <RODAI:ROU=6,TYPE=SL60,VARO=06300000,VARI=05400000,VARC=00000010;EXECUTED
5. <ROEQI:ROU=6,TRU=1-1&&1-15,EQU=1-2-60-1;NOT ACCEPTEDEQUINCORRECT BOARDTYPE
could anyone help!
cfrei (TechnicalUser) 16 Jun 08 4:15 Board TLU76/3 = K sig = TLP30Programming ISDN,Qsig = SLP60
emags (TechnicalUser) 16 Jun 08 5:19 Thanks!
SIP extensionsthread806-1477616Share This Forum Search FAQs Links Jobs Whitepapers MVPs
Check Out Our Whitepaper Library. Click Here.Option43 (TechnicalUser) 3 Jun 08 6:50 Hello,Anyone tell me how to setup SIP extensions on BC13?
I am used to setting up H.323 extensions but now need to setup SIP.
Any help would be kind.
Option43 (TechnicalUser) 6 Jun 08 15:24 Hello,Can anyone help with please?
dusyi (TechnicalUser) 6 Jun 08 16:35 In TSW is no possibility for SIP-Extension.You need TSE.
Option43 (TechnicalUser) 8 Jun 08 14:14 Hello Dusyi,Can you then tell me what and how for TSE please?
SLU (TechnicalUser) 12 Jun 08 6:15 SIP is supported in mxone TSE 3.xYou initiate an IP-extension ( same as for H.323 )in mx-one.e.g. GEDII:DIR=1234,csp=5,lim=1;IPEXI:DIR=1234;Then it is the terminal that desides if it will use SIP or H.323./Stefan
Having trouble initiating EL7 extensionsthread806-1478724Share This Forum Search FAQs Links Jobs Whitepapers MVPs
AntBan (TechnicalUser) 6 Jun 08 15:15 Hello Experts,I'm trying to install EL7 CAS extensions to an MD110 BC13. The Voicemail system is already integrated, but only has 8 EL6 ports. We want to add more users and would like to uses TLU76/3 cards as EL7 extensions.
I had to remove a E1-DPNSS (TLU76/2)card no longer used and placed a TLU76/3 in its place. But everytime i try to initiate the EL7 extensions I get a "incorrect boardtype" error message. Do I need to configure the board position to recognize TLU76/3?
Thanks for your help
Here is what I get from the CLI
<∟EXTEI:DIR=1066,TYPE=EL7,EQU=1-0-00-1,CAT=0; NOT ACCEPTEDINCORRECT BOARDTYPE
dstrang1 (TechnicalUser) 6 Jun 08 16:12 You have to end the TL76/2 (CNBOE:BPOS=xx-x-xx-xx;) and initiate the new TL76/3(CNHUI:BPOS=xx-x-xx-xx;)
You also need to make sure you have the correct ICAT value for EL7 to interface with the voicemail.
Good luck,
Dave Strang
AntBan (TechnicalUser) 6 Jun 08 18:57 Thank You dstrang1,
Turns out I don't have the license required to initiate CAS-Extensions, but at least now i know what I need to do when we do get the license enabled.
Peace :)
which board is responsible of connecting with PSTNthread806-1474030Share This Forum Search FAQs Links Jobs Whitepapers MVPs
amalpbx12 (TechnicalUser) 16 May 08 10:15 Hi guys,Please I wanna ask a question,which board is responsible of connecting PSTN main lines to MD110 PBX. To ALREI or not to ALREI,this is the command
dstrang1 (TechnicalUser) 16 May 08 10:55 Any board with the TLU-xx designation, with the xx being specific to the type of PSTN line (ie, analog, digital, tie, T-1/E-1, ISDN, Qsig etc.). Unless you can connect to the PSTN w/IP, then you need an IPLU.
Good luck,
Dave Strang
LeeMason (MIS) 21 May 08 12:33 We use to use TLU-76 boards to connect to ISDN-30 (E1). Lee MasonOptimal Projects Ltdwww.opl.co.ukwww.backupsanywhere.com
parnum (TechnicalUser) 21 May 08 18:55 you will need TLU76/1 (prom) for Q931/QSIG, make sure you have correct /prom on the board (do CNBIP:BPOS=x-x-x;) as /2 and /3 are no good for ISDN signals.
best parnum
Help!!!!!!!!!!!!!!!!thread806-1474654Share This Forum Search FAQs Links Jobs Whitepapers MVPs
Find A Job or Post a Job Opening Click Here.benaja75 (TechnicalUser) 20 May 08 5:16 I'm triying to delete one number but I receive message that it's busy.The funny thing is I disconnect the cable.What's happens?
HIREI (TechnicalUser) 20 May 08 5:47 May be, this info will be of interest:http://www.tek-tips.com/viewthread.cfm?qid=1452565&page=12 .
whosrdaddy (Vendor) 20 May 08 9:00 printout these commands
SUSIp:DIR=x;
SUDIP:DIR=x;
where x is the extension ----------------------------------------------------- What You See Is What You GetNever underestimate tha powah of tha google!
benaja75 (TechnicalUser) 20 May 08 10:16 Below the printout.
<SUSIP:DIR=2224;STATUS INFORMATION AT 14:16:25 20MAY08DIR TYPE TRAFFIC STATE/PTR LINE STATE/PTR DIV STATE ADD INFO2224 DTS IDLE #027B BLOCKED #03D2 ODN1:IDLE ODN2:IDLE ODN3:IDLE END <SUDIP:DIR=2224;DIRECTORY INFORMATION AT 14:16:45 20MAY08DIRECTORY NUMBER : 2224 TYPE OF DIRECTORY NUMBER : DTSNAME : ADDITIONAL NUMBER :
EXTENSION TERMINAL DATAEQU TERMD ADN CALALT TIMER2-0-20-04 0028 1 0
EXTENSION DIRECTORY CATEGORIESCAT TRAF SERV CDIV ROC TRM ADC CUST LANG BSEC MCOST4 00040415 0207120700 000151111 000001 0 00000002010000 F 0 -
DIGITAL EXTENSION FUNCTION KEY DATAKEY KTYPE FCN VALUE DIG00 FCN TNS 01 FCN CAB 02 FCN CAD 03 FCN TNS 04 SKI F1 05 SKI F2 06 SKI F3 07 SKI F4 09 ODN 2224 10 ODN 2224 11 ODN 2224 12 FCN TNS 13 FCN TNS 14 FCN TNS
GROUP DATA
PARALLEL RINGING DATA
DIVERSION DATA
PAGING DATA
END
whosrdaddy (Vendor) 20 May 08 10:22 try RFPUI:UNIT=DER,LIM=2;
----------------------------------------------------- What You See Is What You GetNever underestimate tha powah of tha google!
benaja75 (TechnicalUser) 20 May 08 11:33 The line stat still the sameCheers
TheCurious (TechnicalUser) 20 May 08 12:20 Sounds silly, but try to connect digital telephone again.blfdp:lim=2,type=kl; gives the reason of blockingrfboi:bpos=2-0-20; restarts the boardbleqe:equ=2-0-20-4,allfm=yes; unblocks the extension
The Curious
benaja75 (TechnicalUser) 20 May 08 12:55 Thanks GUYS for your input Every thing is ok now.Cheers
TLU76 license questionthread806-1460516
Share This
Forum Search FAQs Links Jobs Whitepapers MVPs
DevPlan (TechnicalUser)
24 Mar 08 7:49
I have a BC10 and my license info says:
CODELICENCE TAG ALLOWED USEDANALOGUE-EXTENSION 240 239DIGITAL-EXTENSION 128 125DISA-NUMBER 1 0EXTERNAL-LINE-CAS-ANA 24 15EXTERNAL-LINE-ISDN-USR 120 90GROUP-SWITCH-LINK 4 2LICENSE-FILE 1 0OM-ETH-INTERFACE 1 0OM-V24-INTERFACE 2 2OPERATOR-EXTENSION 2 2
RVA-EXTERNAL 8 0RVA-INTERNAL 12 0SMDR-V24-INTERFACE 1 1TRAFFIC-MEASUREMENT 1 0
My question is:Can I buy an additional TLU76/1 card without license as per what I understand from the above, I still have 30 unused at "External-Line-ISDN-USR"?
rgds, devplan
whosrdaddy (Vendor) 24 Mar 08 8:14
if you want to connect a public PRA, then yes, no problem...
----------------------------------------------------- What You See Is What You GetNever underestimate tha powah of tha google!
DevPlan (TechnicalUser) 24 Mar 08 8:34
Thanks for your fast reply, whorsdaddy!
I am planning to interconnect TLU76/1 with an Asterisk box.Do I need a QSIG license instead or should I be fine with the ISDN-USR license?
rgds, devplan
whosrdaddy (Vendor) 24 Mar 08 10:00
then in that case, you'll need the QSIG license (or the ISDN-NET eventually)
----------------------------------------------------- What You See Is What You GetNever underestimate tha powah of tha google!
DevPlan (TechnicalUser) 28 Mar 08 10:42
What TLU76/1 license is the appropriate to link the MD110 with Sangoma E1 card:
EXTERNAL-LINE-QSIG FAL104466 30 0 or:FAL104507 DSS1 Network Side (2B+D, 30B+D)?
rgds, devplan
whosrdaddy (Vendor) 28 Mar 08 15:37
if you want to do QSIG the first, for ISDN-NET the second...
----------------------------------------------------- What You See Is What You GetNever underestimate tha powah of tha google!
DevPlan (TechnicalUser) 2 Apr 08 4:30
Why wouldn't the "External-Line-ISDN-USR" license work? I.e. I would just need to use a different signaling - don't I?Anybody around who is an expert on ISDN signaling?
rgds, devplan
DevPlan (TechnicalUser) 13 Apr 08 11:22
Is there anybody who successfully setup an MD110 --> Asterisk interfacing with a different signaling than QSIG?
Anybody?
rgds, devplan
fouesnant (TechnicalUser) 14 Apr 08 5:41
Hi
You can connect you TLU76/1 with the existing licence. It is just an configuration in the PATTON to interpret the signalling correctly as coming from a PBX an not from operator.The main difference is that you will not have services, like name, diversion and so on working on the line.But for basic calls with CLIP and CLIR, it is ok.
DevPlan (TechnicalUser) 28 Apr 08 18:12
Thanks fouesnant.
Could you give me a sample config on the PATTON?
Also - I got my TE122P on the Asterisk correctly setup by DIGIUM (excellent service) and have nolonger alarms on my TLU76/1.I have setup all route configs on the MD110 but when I dial the created trunk access code - which should route and ring into my Asterisk box, I get "ROUTE BUSY" displayed on my DBC212. (But a ctcop:bpos=1-0-30; says: * NO-CON *)
I can't figure the reason for this and what am I missing?
rgds, devplan
fouesnant (TechnicalUser) 29 Apr 08 5:34
Hi DevPlan
Here is some PATTON configuration
You will see that port 0 and 2 are used to connect to network while port 1 and 3 are used to be connected to PABX which was an ALACTEL 4200, but that gives no difference if you connect it to Ericsson
#----------------------------------------------------------------## ## SN4638/5BIS/UI ## R4.2 2007-09-19 H323 SIP BRI ## 1970-01-01T00:56:32 ## SN/00A0BA026798 ## Generated configuration file ## ##----------------------------------------------------------------#
cli version 3.20dns-relaywebserver port 80 language ensntp-clientsntp-client server primary 129.132.2.21 port 123 version 4
system
ic voice 0 low-bitrate-codec g729
system clock-source 1 bri 0 0 clock-source 2 bri 0 1 clock-source 3 bri 0 2 clock-source 4 bri 0 3 clock-source 5 bri 0 4
profile napt NAPT_WAN
profile ppp default
profile tone-set default
profile voip default codec 1 g711alaw64k rx-length 20 tx-length 20 codec 2 g711ulaw64k rx-length 20 tx-length 20
profile pstn default
profile sip default
profile dhcp-server DHCPS_LAN network 192.168.1.0 255.255.255.0 include 1 192.168.1.10 192.168.1.99 lease 2 hours default-router 1 192.168.1.1 domain-name-server 1 192.168.1.1
profile aaa default method 1 local method 2 none
context ip router
interface WAN ipaddress dhcp use profile napt NAPT_WAN tcp adjust-mss rx mtu tcp adjust-mss tx mtu
interface LAN ipaddress xxx.xxx.xx.xxx 255.255.255.0 tcp adjust-mss rx mtu tcp adjust-mss tx mtu
context ip router dhcp-server use profile DHCPS_LAN
context cs switch digit-collection timeout 15 address-completion timeout 30 national-prefix 0
routing-table called-e164 SIP_entrant route 0[1-9]........ dest-service Liens_Operateur_FT route 3699 dest-service Liens_Operateur_FT route ... dest-service Liens_PABX ReroutageVersAlcatel
routing-table called-e164 T0_Operateur_entrant route default dest-interface IF_log_SIP
routing-table called-e164 T0_Pabx_entrant route default dest-service Liens_Operateur_FT
mapping-table called-e164 to called-e164 ReroutageVersAlcatel map 100 to 8100 map 101 to 8101 map 102 to 8102 map 103 to 8103 map 104 to 8104 map 110 to 8110 map 112 to 8112 map 113 to 8113 map 114 to 8114 map 116 to 8116 map 117 to 8117 map 118 to 8118 map 120 to 8120 map 121 to 8121 map 122 to 8122 map 123 to 8123 map 124 to 8124 map 125 to 8125 map 133 to 8133 map 140 to 8140
map 141 to 8141 map 151 to 8151 map 152 to 8152 map 158 to 8158 map 192 to 8192 map 193 to 8193 map 194 to 8194 map 195 to 8195 map 196 to 8196 map 197 to 8197 map 198 to 8198 map 199 to 8199 map 200 to 8200 map 201 to 8201 map 202 to 8202 map 203 to 8203 map 204 to 8204 map 205 to 8205 map 206 to 8206 map 207 to 8207 map 208 to 8208 map 209 to 8209 map 210 to 8210 map 211 to 8211 map 212 to 8212 map 213 to 8213 map 214 to 8214 map 215 to 8215 map 216 to 8216 map 217 to 8217 map 218 to 8218 map 219 to 8219 map 220 to 8220 map 221 to 8221 map 222 to 8222 map 223 to 8223 map 224 to 8224 map 225 to 8225 map 226 to 8226 map 227 to 8227 map 228 to 8228 map 229 to 8229
interface isdn IF_log_BRI_0-0 route call dest-table T0_Operateur_entrant dtmf-dialing inband-info accept transparent 1-CallIsNotIsdnToIsdn 2-DestinationNotIsdn 8-InbandInfoAvailable
interface isdn IF_log_BRI_0-2 route call dest-table T0_Operateur_entrant dtmf-dialing inband-info accept transparent 1-CallIsNotIsdnToIsdn 2-DestinationNotIsdn
8-InbandInfoAvailable
interface isdn IF_log_BRI_0-3 route call dest-table T0_Pabx_entrant dtmf-dialing inband-info accept transparent 1-CallIsNotIsdnToIsdn 2-DestinationNotIsdn 8-InbandInfoAvailable
interface isdn IF_log_BRI_0-4 route call dest-table T0_Pabx_entrant dtmf-dialing inband-info accept transparent 1-CallIsNotIsdnToIsdn 2-DestinationNotIsdn 8-InbandInfoAvailable
interface sip IF_log_SIP bind gateway Gateway_Netxserv service default route call dest-table SIP_entrant early-connect early-disconnect
service distribution-group Liens_Operateur_FT cyclic min-concurrent 1 max-concurrent 1 route call 1 dest-interface IF_log_BRI_0-0 route call 2 dest-interface IF_log_BRI_0-2
service distribution-group Liens_PABX cyclic min-concurrent 1 max-concurrent 1 route call 1 dest-interface IF_log_BRI_0-3 route call 2 dest-interface IF_log_BRI_0-4
context cs switch no shutdown
gateway sip Gateway_Netxserv bind interface LAN router
service default defaultserver manual 10.92.13.1 5060 loose-router registration auto 10.92.13.1 5060 user pattont0 authenticate password 6ZGkNNnYu5Cb/4u1YcUaLA== encrypted default register display-name pattont0 phone-context pattont0 user 100 authenticate password A/0WjgD0UNk= encrypted register display-name 100 phone-context 100 user 101 authenticate password A/0WjgD0UNk= encrypted register display-name 101 phone-context 101 user 102 authenticate password A/0WjgD0UNk= encrypted register display-name 102 phone-context 102 user 103 authenticate password A/0WjgD0UNk= encrypted register display-
name 103 phone-context 103 user 104 authenticate password A/0WjgD0UNk= encrypted register display-name 104 phone-context 104 user 110 authenticate password A/0WjgD0UNk= encrypted register display-name 110 phone-context 110 user 112 authenticate password A/0WjgD0UNk= encrypted register display-name 112 phone-context 112 user 113 authenticate password A/0WjgD0UNk= encrypted register display-name 113 phone-context 113 user 114 authenticate password A/0WjgD0UNk= encrypted register display-name 114 phone-context 114 user 116 authenticate password A/0WjgD0UNk= encrypted register display-name 116 phone-context 116 user 117 authenticate password A/0WjgD0UNk= encrypted register display-name 117 phone-context 117 user 118 authenticate password A/0WjgD0UNk= encrypted register display-name 118 phone-context 118 user 120 authenticate password A/0WjgD0UNk= encrypted register display-name 120 phone-context 120 user 121 authenticate password A/0WjgD0UNk= encrypted register display-name 121 phone-context 121 user 122 authenticate password A/0WjgD0UNk= encrypted register display-name 122 phone-context 122 user 123 authenticate password A/0WjgD0UNk= encrypted register display-name 123 phone-context 123 user 124 authenticate password A/0WjgD0UNk= encrypted register display-name 124 phone-context 124 user 125 authenticate password A/0WjgD0UNk= encrypted register display-name 125 phone-context 125 user 133 authenticate password A/0WjgD0UNk= encrypted register display-name 133 phone-context 133 user 140 authenticate password A/0WjgD0UNk= encrypted register display-name 140 phone-context 140 user 141 authenticate password A/0WjgD0UNk= encrypted register display-name 141 phone-context 141 user 151 authenticate password A/0WjgD0UNk= encrypted register display-name 151 phone-context 151 user 152 authenticate password A/0WjgD0UNk= encrypted register display-name 152 phone-context 152 user 158 authenticate password A/0WjgD0UNk= encrypted register display-name 158 phone-context 158 user 192 authenticate password A/0WjgD0UNk= encrypted register display-name 192 phone-context 192 user 193 authenticate password A/0WjgD0UNk= encrypted register display-name 193 phone-context 193 user 194 authenticate password A/0WjgD0UNk= encrypted register display-name 194 phone-context 194 user 195 authenticate password A/0WjgD0UNk= encrypted register display-name 195 phone-context 195 user 196 authenticate password A/0WjgD0UNk= encrypted register display-name 196 phone-context 196 user 197 authenticate password A/0WjgD0UNk= encrypted register display-name 197 phone-context 197
user 198 authenticate password A/0WjgD0UNk= encrypted register display-name 198 phone-context 198 user 199 authenticate password A/0WjgD0UNk= encrypted register display-name 199 phone-context 199 user 200 authenticate password A/0WjgD0UNk= encrypted register display-name 200 phone-context 200 user 201 authenticate password A/0WjgD0UNk= encrypted register display-name 201 phone-context 201 user 202 authenticate password A/0WjgD0UNk= encrypted register display-name 202 phone-context 202 user 203 authenticate password A/0WjgD0UNk= encrypted register display-name 203 phone-context 203 user 204 authenticate password A/0WjgD0UNk= encrypted register display-name 204 phone-context 204 user 205 authenticate password A/0WjgD0UNk= encrypted register display-name 205 phone-context 205 user 206 authenticate password A/0WjgD0UNk= encrypted register display-name 206 phone-context 206 user 207 authenticate password A/0WjgD0UNk= encrypted register display-name 207 phone-context 207 user 208 authenticate password A/0WjgD0UNk= encrypted register display-name 208 phone-context 208 user 209 authenticate password A/0WjgD0UNk= encrypted register display-name 209 phone-context 209 user 210 authenticate password A/0WjgD0UNk= encrypted register display-name 210 phone-context 210 user 211 authenticate password A/0WjgD0UNk= encrypted register display-name 211 phone-context 211 user 212 authenticate password A/0WjgD0UNk= encrypted register display-name 212 phone-context 212 user 213 authenticate password A/0WjgD0UNk= encrypted register display-name 213 phone-context 213 user 214 authenticate password A/0WjgD0UNk= encrypted register display-name 214 phone-context 214 user 215 authenticate password A/0WjgD0UNk= encrypted register display-name 215 phone-context 215 user 216 authenticate password A/0WjgD0UNk= encrypted register display-name 216 phone-context 216 user 217 authenticate password A/0WjgD0UNk= encrypted register display-name 217 phone-context 217 user 218 authenticate password A/0WjgD0UNk= encrypted register display-name 218 phone-context 218 user 219 authenticate password A/0WjgD0UNk= encrypted register display-name 219 phone-context 219 user 220 authenticate password A/0WjgD0UNk= encrypted register display-name 220 phone-context 220 user 221 authenticate password A/0WjgD0UNk= encrypted register display-name 221 phone-context 221 user 222 authenticate password A/0WjgD0UNk= encrypted register display-name 222 phone-context 222 user 223 authenticate password A/0WjgD0UNk= encrypted register display-name 223 phone-context 223 user 224 authenticate password A/0WjgD0UNk= encrypted register display-
name 224 phone-context 224 user 225 authenticate password A/0WjgD0UNk= encrypted register display-name 225 phone-context 225 user 226 authenticate password A/0WjgD0UNk= encrypted register display-name 226 phone-context 226 user 227 authenticate password A/0WjgD0UNk= encrypted register display-name 227 phone-context 227 user 228 authenticate password A/0WjgD0UNk= encrypted register display-name 228 phone-context 228 user 229 authenticate password A/0WjgD0UNk= encrypted register display-name 229 phone-context 229
gateway sip Gateway_Netxserv no shutdown
port ethernet 0 0 medium auto encapsulation ip bind interface WAN router no shutdown
port ethernet 0 1 medium auto encapsulation ip bind interface LAN router no shutdown
port bri 0 0 clock slave encapsulation q921
q921 permanent-layer2 protocol pp uni-side user encapsulation q931
q931 protocol dss1 uni-side user bchan-number-order ascending-cyclic encapsulation cc-isdn bind interface IF_log_BRI_0-0 switch
port bri 0 0 no shutdown
port bri 0 1 clock auto encapsulation q921
q921 uni-side auto
encapsulation q931
q931 protocol dss1 uni-side net bchan-number-order ascending
port bri 0 1 shutdown
port bri 0 2 clock slave encapsulation q921
q921 permanent-layer2 protocol pp uni-side user encapsulation q931
q931 protocol dss1 uni-side user bchan-number-order ascending-cyclic encapsulation cc-isdn bind interface IF_log_BRI_0-2 switch
port bri 0 2 no shutdown
port bri 0 3 clock master encapsulation q921
q921 permanent-layer2 protocol pp uni-side net encapsulation q931
q931 protocol dss1 uni-side net bchan-number-order ascending-cyclic encapsulation cc-isdn bind interface IF_log_BRI_0-3 switch
port bri 0 3 no shutdown
port bri 0 4 clock master encapsulation q921
q921 permanent-layer2 protocol pp uni-side net encapsulation q931
q931 protocol dss1 uni-side net bchan-number-order ascending-cyclic encapsulation cc-isdn bind interface IF_log_BRI_0-4 switch
port bri 0 4 no shutdown
good luck
DevPlan (TechnicalUser) 29 Apr 08 11:39
Thanks for the data.
Now, actually I don't have a PATTON connected but a DIGIUM TE122P that sits in my asterisk box.
Why would I get a "ROUTE BUSY" displayed on my DBC212 when I dial the route access code 9000?
Here are my route settings:
<roddp:dest=9000;EXTERNAL DESTINATION ROUTE DATADEST DRN ROU CHO CUST ADC TRC SRT NUMACK PRE9000 8 0005000000000250000 0 5 0 8 1 0005000000000250000 0 5 0 8 2 0005000000000250000 0 5 0 8 3 0005000000000250000 0 5 0 8 4 0005000000000250000 0 5 0
<NADAP:NUMTYP=ED;NUMBER ANALYSIS DATA TYPE OF SERIES NUMBER SERIES EXTERNAL DESTINATION CODE 114 2800 2828 2996 - 2999 9000 - 9599
<RODAP:ROU=8;ROUTE DATA
ROU TYPE VARC VARI VARO FILTER 8 SL60 H'00000110 H'15400000 H'06410000 NO
<roedp:rou=8,tru=all;ROUTE EQUIPMENT DATAROU TRU EQU SQU INDDAT 8 001-10 001-0-30-01 H'0000000000008 001-11 001-0-30-02 H'0000000000008 001-12 001-0-30-03 H'0000000000008 001-13 001-0-30-04 H'0000000000008 001-14 001-0-30-05 H'0000000000008 001-15 001-0-30-06 H'0000000000008 001-16 001-0-30-07 H'0000000000008 001-17 001-0-30-08 H'0000000000008 001-18 001-0-30-09 H'0000000000008 001-19 001-0-30-10 H'0000000000008 001-20 001-0-30-11 H'0000000000008 001-21 001-0-30-12 H'0000000000008 001-22 001-0-30-13 H'0000000000008 001-23 001-0-30-14 H'0000000000008 001-24 001-0-30-15 H'0000000000008 001-40 001-0-30-17 H'0000000000008 001-41 001-0-30-18 H'0000000000008 001-42 001-0-30-19 H'0000000000008 001-43 001-0-30-20 H'0000000000008 001-44 001-0-30-21 H'0000000000008 001-45 001-0-30-22 H'0000000000008 001-46 001-0-30-23 H'0000000000008 001-47 001-0-30-24 H'0000000000008 001-48 001-0-30-25 H'0000000000008 001-49 001-0-30-26 H'0000000000008 001-50 001-0-30-27 H'0000000000008 001-51 001-0-30-28 H'0000000000008 001-52 001-0-30-29 H'0000000000008 001-53 001-0-30-30 H'0000000000008 001-54 001-0-30-31 H'000000000000
rgds, devplan
fouesnant (TechnicalUser) 30 Apr 08 10:56
Hi
I guess that it is your digium box configuration that reply this message.You should make a trace on SLP60 on your PBX and analyse the result with STI (from SAM tool Box) to see why you get this message, or if the Digium box offer it (Patton does) see what are the incoming messages.
CNLIP
thread806-1469849
Share This
Forum Search FAQs Links Jobs Whitepapers MVPs
Monrovia (TechnicalUser)
30 Apr 08 3:17
hi all
one small doubt it is.using this command CNLIP:LIM=1; i was getting all the data regarding the boards active, inactive in that lim like
CODE CNLIP:LIM=1;
LIM CONFIGURATION LIM NUMBER 1 LIM CONTROL LIM CONTROL NUMBER OF SERVICE SYSTEM SIDE SYSTEM STATE PCM-LINKS STATE LIM A EXECUTING 0 ACTIVE B NOT EQUIPPED MEMORY MEMORY MEMORY SPARE VOLUME SPARE AFTER PACKING 65535 KB 12248 KB 12248 KB BUAR1 3810 KB BUAR2 2989 KB
NUMBER OF BPOS BOARDID INDIVIDUALS SERVICE STATE 001-0-00 57 32 ACTIVE 001-0-10 102 32 ACTIVE 001-0-20 77 16 ACTIVE 001-0-22 77 16 ACTIVE 001-0-30 77 16 ACTIVE 001-0-32 87 16 ACTIVE 001-0-40 87 16 ACTIVE 001-0-42 87 16 ACTIVE 001-0-50 87 16 ACTIVE 001-0-52 87 16 ACTIVE 001-0-60 106 16 ACTIVE 001-0-62 NOT EQUIPPED 001-0-63 76 8 ACTIVE
001-0-70 42 32 ACTIVE 001-1-00 57 32 ACTIVE 001-1-10 102 32 ACTIVE 001-1-20 77 16 ACTIVE 001-1-22 87 16 ACTIVE 001-1-30 57 32 ACTIVE 001-1-40 108 16 ACTIVE 001-1-42 NOT EQUIPPED 001-1-43 NOT EQUIPPED 001-1-50 27 32 ACTIVE 001-1-60 106 16 ACTIVE 001-1-62 77 16 ACTIVE 001-1-70 57 32 ACTIVE
but now i am only getting a small description like
CODE<CNLIP:LIM=1;
LIM CONFIGURATION LIM NUMBER 1 LIM CONTROL LIM CONTROL NUMBER OF SERVICE SYSTEM SIDE SYSTEM STATE PCM-LINKS STATE LIM A EXECUTING 0 ACTIVE B NOT EQUIPPED MEMORY MEMORY MEMORY SPARE VOLUME SPARE AFTER PACKING 65535 KB 12248 KB 12248 KB BUAR1 3810 KB BUAR2 2989 KB
why like this?
now what i am doing is using the command CNBIP:LIM=1; i am finding out. to get back the same details using cnlip, what is wrong with the system?
parnum (TechnicalUser) 30 Apr 08 3:28
CNLIP:LIM=1,DEV=YES;
Monrovia (TechnicalUser) 30 Apr 08 5:17
oops!!!!
my mistake. i fogot it ;)
DISA and authorization code
thread806-1467092Share This Forum Search FAQs Links Jobs Whitepapers MVPs
bb34nne (Programmer)
18 Apr 08 5:38
Hi!
Can someone write here how can I set code for DISA calls. I want to set code when someone call DISA number from outside line, first they have to enter code and then(if code is correct)dial number. Now I have DISA but with no protection.
Thanks bb34nne
rfpui (TechnicalUser) 18 Apr 08 7:56 From AlexPARNUM=184 DISA with or without authorization code
0 Common (central) authorization code is required on DISA calls 1 Individual (regional) authorization code is required on DISA calls 2 Individual or common authorization code is required on DISA calls 3 Authorization code is not required on DISA calls ----------------------------------If anything can go wrong, it will.(Murphy's Law)
bb34nne (Programmer) 21 Apr 08 2:42 How to set up autorization code for DISA? I tried to set individual code for DISA, but I get message "DIR not in range". I used ASPAC:PARNUM=184,PARVAL=1, and AUCOI:DIR="DISA number",AUTH=XXXX,CAT=10,CILCOD=XXXX;
Another question: how to set that nothing is possible to dial from DISA, only when I enter authcode is possible to dial outside. Now I can dial everything thru DISA, but I want to restrict that.
thanks bb34nne
fouesnant (TechnicalUser) 21 Apr 08 3:32 Hi
Here is an extract from Alex how to dial authorization code with DISA.Authorisation code can be individual (AUCOI:DIR=...), or Common (AUCOI:AUTH=...;)
With common authorization code
DISA number DT * FC * AUTH.CODE # DT + Wanted number DISA number DT * FC * AUTH.CODE * FC * ACO.CODE # DT + Wanted number.
With individual authorization code
DISA number DT * FC * RAC * DIR # DT + Wanted number DISA number DT * FC * RAC * DIR * FC * ACO.CODE # DT + Wanted number.
Without authorization code (only if permitted)
DISA number DT + Wanted number DISA number DT * FC * ACO.CODE # DT + Wanted number.
DT Dial tone FC Feature code AUTH.CODE Authorization code RAC Individual Authorization code DIR Directory number ACO.CODE Account code
So if you want to analyze the dialled number, you can perfom it via the autorisation code, or from the Leat code routing.
I would prefer to use Mobile Extension to provide a check for allowing callers to use the PBX capacity.
Good Luck
lalrl (TechnicalUser) 22 Apr 08 1:54 I can change the profile of my ext. via disa:
Disa-nr. DT *72*RAC*ext.# DT *10*ext*profile#
Now I try to make *21* or *22* but it does not work. Is only Personal Number supported? What else can I do with my extension via Disa?
fouesnant (TechnicalUser) 22 Apr 08 3:41 Hi
just concentrate on what's DISA meanDirect Inward Service Access; that does not mean that you will have all facilities available.If you want to make diversion,you can test this procedure; your phone must be diverted to itself first and then you can may be do the procedure *21*your phone*answering phone#Regarding external divertion, this is not possible as the action is made directly on the phone that make the request, and DISA ferature is not attached to a phone.
The best solution is to us Mobile Extension, which is exactly made for your need.
Best regards
Batteries MD110thread806-1562013Share This Forum Search FAQs Links Jobs Whitepapers MVPs
Find A Job or Post a Job Opening Click Here.bb34nne (Programmer) 31 Jul 09 3:34
Does someone know which batteries, model of batteries can work with MD110? System is CXP1010101/4/TSWSP02/R3A, 1 LIM, 4 magazines. Batteries that I have in exchange works only 30 minutes when is a blackout. bb34nne
subzerocool (MIS) 1 Aug 09 1:42 How many batteries do you have? I'm not at the office but I can find out for you, I don't have a copy of ALEX on my computer so I can't pull it up for you but I do have the batteries at the office.
bb34nne (Programmer) 1 Aug 09 5:41 I have 4 battery in exchange. Can you post which kind of battery is good for MD110? bb34nne
subzerocool (MIS) 1 Aug 09 5:47 I will be heading into the office in 8 hours(it's 2:45AM here). I will check for you. When I worked at Ericsson a long time ago, we had a room with batteries separate. A contractor came and did maintenance on the set up. I'm not sure how long the ones we have will last.
subzerocool (MIS) 1 Aug 09 19:05 I have have systems at work for my lab with 4 batteries in each. They are the orange SBS 30 batteries that are 12V 26Ah each.
whosrdaddy (Vendor) 2 Aug 09 7:15 normal battery life is 4 years. If you use larger batteries (like for cars/trucks) that can be refilled with water, life can be longer.
/Daddy ----------------------------------------------------- What You See Is What You GetNever underestimate tha powah of tha google!
djudjuman (TechnicalUser) 2 Aug 09 7:35 In stead of starting a new thread, I'll put my request here.
I'm also looking for MD110 batteries.The specification of the battery is as follows:12V 26AHHeigth (H) = 15CMWidth (W) = 10CMLength (L) = 25CM
Who can give me the name of a supplier?
subzerocool (MIS) 2 Aug 09 16:44 Sorr I didn't mention the brand, the ones we have in our MD's are Hawker.
slash50 (TechnicalUser) 6 Aug 09 5:35 Any batteries can be used, as long as the total in the string is 48v. If you want longer time, use smaller voltage batteries with higher capacity. You will require more space though.
DUFQI (TechnicalUser) 6 Aug 09 5:54 Welcome to Enersys - Hawker Motive Power Wherever in Europe there is a need for motive power batteries or chargers, Enersys is here to provide the perfect solution. The Hawker-branded battery ranges, matched chargers and battery management systems deliver sustained, trouble free and economical performance under the most demanding operational conditions. Hawker Motive Power is part of EnerSys, the world leader in industrial batteries with activities covering reserve power (standby batteries for telecoms, UPS etc), defence, and motive power (traction batteries and
chargers).
We are the largest European manufacturer of industrial lead-acid batteries, and have locations and service networks spanning Europe, Africa, Middle East - and the rest of the world.
merlin3355 (TechnicalUser) 25 Aug 09 12:13 HI
Is it for a Consono?
If so SBS30 are standard. I have mpst type of LIM let me know and I will have a look
Merlin
MD110 TTY Commandsthread806-1457425Share This Forum Search FAQs Links Jobs Whitepapers MVPs
DASIS (MIS)
11 Mar 08 4:24
Can anyone please provide a list of all the TTY Commands. In Particular one to check if a digital phone is unplugged from the port where it is assigned a number and EQU to enable recovery of the EQU and extension. Thanks in advance.
assarvahid (MIS) 11 Mar 08 7:53 BLFDP will show you if the phone is not connected and Ksddp shows you the equ position.
DASIS (MIS) 11 Mar 08 19:25 Many Thanks. Do you perhaps have a list of all the TTY commands for the MD110?
drewMk2 (TechnicalUser) 11 Mar 08 20:08 susip:dir=XXXX;
drewMk2 (TechnicalUser) 11 Mar 08 23:43 it will be easier to get a logon to Ericsson Info channel and download Alex. this is the help publication for MD110/MX-One and everything you will ever need to know.
Monrovia (TechnicalUser) 12 Mar 08 4:31 open alex
go to General - Commands in ASB 501 04
all the commands are given in a row
Can i Add more boards in this Magazine?thread806-1451508Share This
Forum Search FAQs Links Jobs Whitepapers MVPs
Monrovia (TechnicalUser)
18 Feb 08 3:04
I am new to this MD110. I am copypasting my CNLIP:LIM=1,Dev=YES; here. please advice me, that whether i can add more boards in this magazine. it is showing, some time slots are free (not equiped). And my license capacity is fully open for anything.
<CADAP;CALENDAR DATAIDENTITY=MD110 VERSION=CXP1010101/2/BC12SP7/R4ACALENDAR TIME NOT VALID10:03:12MON 18 FEB 2008END <CNLIP:LIM=1,DEV=YES;
LIM CONFIGURATIONLIM NUMBER 1 LIM CONTROL LIM CONTROL NUMBER OF SERVICE SYSTEM SIDE SYSTEM STATE PCM-LINKS STATE LIM A EXECUTING 0 ACTIVE B NOT EQUIPPED MEMORY MEMORY MEMORY SPARE VOLUME SPARE AFTER PACKING 65535 KB 12248 KB 12248 KB BUAR1 3810 KB BUAR2 2989 KB
DEVICE BOARDS NUMBER OF BPOS BOARDID INDIVIDUALS SERVICE STATE 001-0-00 57 32 ACTIVE 001-0-10 102 32 ACTIVE 001-0-20 77 16 ACTIVE 001-0-22 77 16 ACTIVE 001-0-30 77 16 ACTIVE 001-0-32 87 16 ACTIVE 001-0-40 87 16 ACTIVE 001-0-42 87 16 ACTIVE 001-0-50 87 16 ACTIVE 001-0-52 87 16 ACTIVE 001-0-60 106 16 ACTIVE 001-0-62 NOT EQUIPPED 001-0-63 76 8 ACTIVE 001-0-70 42 32 ACTIVE 001-1-00 57 32 ACTIVE 001-1-10 102 32 ACTIVE 001-1-20 77 16 ACTIVE 001-1-22 87 16 ACTIVE 001-1-30 57 32 ACTIVE 001-1-40 108 16 ACTIVE
001-1-42 NOT EQUIPPED 001-1-43 NOT EQUIPPED 001-1-50 27 32 ACTIVE 001-1-60 106 16 ACTIVE 001-1-62 77 16 ACTIVE 001-1-70 57 32 SYSTEM BLOCKED
END<
DisWire (TechnicalUser) 18 Feb 08 4:04 Seems to me that you can put a 8port card in each of these slots....1-0-621-1-421-1-43Alternatively you can put a 8port card in 1-0-62 and a 16port in 1-1-42 but this will make 1-1-43 unuseable.
Make sure that the slots are physically available though. Sometimes you may find a HDU or other card that doesn't use timeslots sitting in a card postion.
Monrovia (TechnicalUser) 18 Feb 08 4:08 thanks diswire.
what about the board on slot 001-1-70. what does "system blocked" means. is it manually blocked? so can remove it and put some other board over there?
DisWire (TechnicalUser) 18 Feb 08 7:45 As the board ID is 57 then there should be a TLU76/1 (ISDN30) card in position 1-1-70. As the system has blocked the card it's safe to assume that it's not in use.As long as you don't need an additional ISDN30 then there's no reason why it couldn't be removed and replaced with something else. Depending on the magazine if you remove the TLU76/1 then slot 1-1-72 may also become available.
GFDANNHAUSER (Programmer) 26 Feb 08 10:15 Hi Do Yourself a favour, do a SYEDP:BPOS=1-1-70; first, and see if there is anything tied to it.
BR
Monrovia (TechnicalUser) 27 Feb 08 3:19 I am sorry, that time when i take cnlip, the board has some problems. now the tlu76 at 1-1-70 is working - active
DEVICE BOARDS NUMBER OF BPOS BOARDID INDIVIDUALS SERVICE STATE 001-0-00 57 32 ACTIVE 001-0-10 102 32 ACTIVE 001-0-20 77 16 ACTIVE 001-0-22 77 16 ACTIVE 001-0-30 77 16 ACTIVE 001-0-32 87 16 ACTIVE 001-0-40 87 16 ACTIVE 001-0-42 87 16 ACTIVE 001-0-50 87 16 ACTIVE 001-0-52 87 16 ACTIVE 001-0-60 106 16 ACTIVE
001-0-62 NOT EQUIPPED 001-0-63 76 8 ACTIVE 001-0-70 42 32 ACTIVE 001-1-00 57 32 ACTIVE 001-1-10 102 32 ACTIVE 001-1-20 77 16 ACTIVE 001-1-22 87 16 ACTIVE 001-1-30 57 32 ACTIVE 001-1-40 108 16 ACTIVE 001-1-42 NOT EQUIPPED 001-1-43 NOT EQUIPPED 001-1-50 27 32 ACTIVE 001-1-60 106 16 ACTIVE 001-1-62 77 16 ACTIVE 001-1-70 57 32 ACTIVE
how to intrude an external line??thread806-1449474Share This Forum Search FAQs Links Jobs Whitepapers MVPs
Check Out Our Whitepaper Library. Click Here.user25 (TechnicalUser) 9 Feb 08 6:06 Hi all!I found in ALEX that's possible to make intrusion and forced the extenal line to be disconectedwe have just to dial:Dial *44*individual external line number# and external destination code (busy tone). an press 4.. But after pressing 4 i always hear the busy toneIn my case The externa line belong to rou=41 whose category is:
rocap:rou=41;ROUTE CATEGORY DATAROU SEL TRM SERV NODG DIST DISL TRAF SIG BCAP41 013000000000 4 2100030000 0 30 128 01151506 200000000000 001100
My extension category is:<kscap:dir=1007;KEY SYSTEM CATEGORY PRINTDIR TRAF SERV CDIV ROC ITYPE TRM ADC 1007 03151515 00131207 011151000 0000 1 0 00000002011
Other extension have cat=2<exccp:cat=2;EXTENSION CATEGORY CODE CAT TRAF SERV CDIV ROC 2 01020202 00021207 001151000 0000
Is there problem in category parameters??
Thank you for all!
bija77 (TechnicalUser) 11 Feb 08 7:50
hi user25,check the command:ASPAP:PARNUM=23; (suffix digit to requesting intrusion)it's by default 8then from dir 1007 try to Dial * 0 * individual external line number # external destination code then when you get the busy tone press the suffix digit to intrusion (i.e 8).
good luck
CIL thread806-1445672Share This Forum Search FAQs Links Jobs Whitepapers MVPs
642234 (TechnicalUser)
26 Jan 08 16:24
Hi Dear All,
I have BC 12 version. i want to intiate CIL in MD 110. Please can you send me all commands with parameters. Thanks
kank (IS/IT--Management) 28 Jan 08 9:20 rs-232 or ip or cil on hdu?
642234 (TechnicalUser) 28 Jan 08 12:22 Dear Kank,
Both RS 232 and also on CIL on hard disk
Thanks
642234 (TechnicalUser) 30 Jan 08 7:53
Hi Kank,,can youhelp me regarding CIL on rs 232 and cil on Hard diskThanks
doktor (IS/IT--Management) 30 Jan 08 8:30
Hello!
Here is the CIL on HDU initiation commands...
Call Information Logging on HDU:
FIDAP:PATH=/SYSN/USR1/ACS/CIL/*.*;CLDFI:PATH=/SYSN/USR1/ACS/CIL,FILE=CILBUF,USER=CIL-2,PRIO=D;CLOHI:FILE=CILBUF,FORM=2,DMPSIZ=4,DISCR=0 or 2;CLODI:FILE=CILBUF;
CLTGI;
Use these print commands to verify the result:FIDAP:PATH=/SYSN/USR1/ACS/CIL/*.*;CLDFP;CLINP;And see the raw SMDR/CDR data in the directory on the HDU:FIFCP:PATH=/SYSN/USR1/ACS/CIL/CILBUF20080130,FORMAT=ASCII;
CIL through RS-232 on the NIU board:IOEQI:EQU=x-x-xx-x,IODEV=SYSNET,USAGE=OUT;CLDFI:FILE=NIU-CIL,IODEV=SMDR-CIL1,USER=CIL-1;CLOHI:FILE=NIU-CIL,FORM=2,DMPSIZ=2,DISCR=0 or 2;CLODI:FILE=NIU-CIL;CLTGI;
///doktor
642234 (TechnicalUser) 31 Jan 08 11:31
Dear Dokter,Thanks a lot
Monrovia (TechnicalUser) 10 Feb 08 7:25 thank you dokto :D
time slotsthread806-1444457Share This Forum Search FAQs Links Jobs Whitepapers MVPs
Tek-Tips Forums is Member Supported. Click Here to donate.new2md (TechnicalUser) 23 Jan 08 3:58 Hi ! everyone !1- Please someone define the term time slot and its funtionality.2- How many TS are consumed by NIU2, LPU5, ELU 32, and IPLU 3- Does the TS keeps changing depending on usage of any card
rgds
whosrdaddy (Vendor) 23 Jan 08 11:35
1) a timeslot is nothing more than one channel (64kb) on a PCM bus (compare it with a E1/T1)the DSU board can provide 256 timeslots, the DSU is Linked to the LSU board which provides 1024 timeslots (so max 4 DSU's on LSU = max 4 magazines)
2) NIU2 =16 LPU5 = 4 - 32, depends on board position ELU32 = 16 IPLU = 323) each board position has its own dedicated timeslots
hope this clears your mind...
/Daddy----------------------------------------------------- What You See Is What You GetNever underestimate tha powah of tha google!
new2md (TechnicalUser) 24 Jan 08 3:31 Brilliant !
External Destination CATthread806-1440731Share This Forum Search FAQs Links Jobs Whitepapers MVPs
bb34nne (Programmer)
10 Jan 08 5:09
Hi all!
I have some problems with External Destinatios. Is it possible to set category for ED? To set outgoing call barring? With extensions is easy, but set restriction for external destination in MD110 is difficult(for me). How can I set that?
patcher (TechnicalUser) 10 Jan 08 15:35 You need to set Call Descrimination data under NADAP. Then use this call descrimination in setting up your extension CAT. You can check it in Alex document. Regards.
bb34nne (Programmer) 11 Jan 08 1:51 Can someone post example?
bb34nne (Programmer) 21 Jan 08 7:22 I contacted Ericsson about this problem and they said that this is not possible. I dont understand. How is that impossible? We use that external destination like regular telephone and I want to restrict phone calls on that ED. Someone here said that this is possible?
<RODDP:DEST=2400;EXTERNAL DESTINATION ROUTE DATADEST DRN ROU CHO CUST ADC TRC SRT NUMACK PRE2400 93 00050000000002500000000000 0 1 0 bb34nne
parnum (TechnicalUser) 21 Jan 08 9:49
if you want to restrict access to 2400 from extns in only some CAT, then in NADAP numtyp CD set 2400 with certain TRAF related to ext CAT and this will restrict the same as any other number restriction. If this is now what you are asking then please be clear about what you want to do.
best parnum
bb34nne (Programmer) 21 Jan 08 13:35 No, I know that. I want to restrict calls FROM dest 2400, not restrict calls TO dest 2400. Everybody can dial call 2400 and get that number.
Did you understood me?? bb34nne
whosrdaddy (Vendor) 21 Jan 08 14:23 only way to do that is to use the traffic matrix.
please do understand that TCMAP only works on a route level not on destinations. ----------------------------------------------------- What You See Is What You GetNever underestimate tha powah of tha google!
bb34nne (Programmer) 22 Jan 08 1:36 OK, thanks! Another question: do you recommend that I create two routes, one where is everything allowed, and one where I block international calls? And then initiate dest 2400 on route where I blocked international numbers?
thanks again for answers bb34nne
bb34nne (Programmer) 23 Jan 08 2:19 How to create 2 routes on one E1/T1 connection? Now I have 1 route(trunks 1-1&&1-31), is it OK to initiate another route on trunks 1-25&&1-31? Will it work? Do I have to do something with signalling? bb34nne
Number Conversion. ****Urgent!thread806-1438143Share This Forum Search FAQs Links Jobs Whitepapers MVPs
Tek-Tips Forums is Member Supported. Click Here to donate.sx0sx (TechnicalUser) 30 Dec 07 15:06 Hi Guys,
Currently my 1st TSW(6xxx series ext) is connected to a router(Netrix) using E&M(rou 77).Then the 1st TSW is connected to my 2nd TSW(8xxx series ext) using a Q-sig(rou 67).
The idea is to make the 1st TSW as a transit whereby all incoming from Netrix that start wif 8xxx will be sent to the 2nd TSW via Q-sig.
My question is, how can i convert incoming call to the 1st TSW and then point it to the 2nd TSW whenever the received number start from 8xxx series number.
for example :i used nutri like below but it wont work.
NUTRP:ENTRY=ALL;NUMBER CONVERSION DATA
ENTRY CNVTYP NUMTYP ROU PRE TRC CONT BCAP HLC8828 0 6 77 70068828 4
*7006 is a destination code to seize the Q-sig.*8828 is basically a number that i receive from the E&M.
appreciate if someone can give a help. Thanks.
mundus (TechnicalUser) 30 Dec 07 15:54 Hi' why not make a dest "8" from TSW1 to TSW2 and then use the recieved 8xxx to point out this dest ?Normally you don't receive TON from a E&M connection, so here you must use the NUMTYP 5 ( Unknown ).
sx0sx (TechnicalUser) 30 Dec 07 21:16 hi mundus!
i cannot use "8" for dest since it was a suffix digit for call pickup.
so, you mean i should do the programming as this? :
NUTRP:ENTRY=ALL;NUMBER CONVERSION DATA
ENTRY CNVTYP NUMTYP ROU PRE TRC CONT BCAP HLC8828 0 5 77 70068828 4
How about the CNVTYP? should i leave it as 0 which means as received B-number?
mundus (TechnicalUser) 31 Dec 07 10:09 Yes, but keep it more simple:ENTRY CNVTYP NUMTYP ROU PRE TRC CONT BCAP HLC8828 0 5 77 7006
whosrdaddy (Vendor) 1 Jan 08 3:24 yet more simple is
ENTRY CNVTYP NUMTYP ROU PRE TRC CONT BCAP HLC8 0 5 77 7006
(do not forget to use monotags (tt) folks)
please show rocap, rodap and roddp:dest=7006 ----------------------------------------------------- What You See Is What You GetNever underestimate tha powah of tha google!
sx0sx (TechnicalUser) 8 Jan 08 3:06 thanks for replying.
here is the rocap and rodap for both q-sig and E&M.
For Q-sig :ROCAP<ROCAP:ROU=67;ROUTE CATEGORY DATAROU SEL TRM SERV NODG DIST DISL TRAF SIG BCAP67 0110000000000010 5 3110000000 0 30 128 03050515 311100100031 111111
RODAP<RODAP:ROU=67;ROUTE DATAROU TYPE VARC VARI VARO FILTER 67 SL60 H'00000310 H'15400000 H'06B00000 NO
RODDP DEST=7006<RODDP:DEST=7006;EXTERNAL DESTINATION ROUTE DATADEST DRN ROU CHO CUST ADC TRC SRT NUMACK PRE7006 67 06061000000002500060000000 0 5 0
THIS IS WHERE THE INCOMING COMES FROM (E&M)ROCAP<ROCAP:ROU=77;ROUTE CATEGORY DATAROU SEL TRM SERV NODG DIST DISL TRAF SIG BCAP77 0120000000000010 7 2110000000 0 30 128 00050515 211100000000 001100
RODAP<RODAP:ROU=77;ROUTE DATAROU TYPE VARC VARI VARO FILTER 77 TL22 H'031F0132 H'00012040 H'00011000 NO
mundus (TechnicalUser) 8 Jan 08 10:32 You need to open up for number conversion, last digits in SERV - 2110000001.
sx0sx (TechnicalUser) 8 Jan 08 21:12 Thanks, i will give it a try. will update u guys the outcome.
ALL Analogus Extensions not WORKING!!!thread806-1437170Share This Forum Search FAQs Links Jobs Whitepapers MVPs
Check Out Our Whitepaper Library. Click Here.admiralzino (IS/IT--Management) 22 Dec 07 10:39 Dear all,
I'm in a tight corner. in one of my sites, all the analogue extensions connected to MAG1 are not working!! analogue extensions on MAG 0 are working and digital extensions are also working. i've exhausted all ideas. does someone have an idea what the problem is? MD revision is
VERSION: CXP1010101/4/TSWSP02/R3A
thanks.
The Admiral
whosrdaddy (Vendor) 22 Dec 07 10:48 maybe you have a defective board?
please do a CNLIP:LIM=1,DEV=YES; and ALLOP; ----------------------------------------------------- What You See Is What You GetNever underestimate tha powah of tha google!
admiralzino (IS/IT--Management) 22 Dec 07 14:01 See below for cnlip printout. the alarm log is cleared.
<CNLIP:LIM=1,DEV=YES;
LIM CONFIGURATION LIM NUMBER 1 LIM CONTROL LIM CONTROL NUMBER OF SERVICE SYSTEM SIDE SYSTEM STATE PCM-LINKS STATE LIM A EXECUTING 0 ACTIVE B EQUIPPED MEMORY MEMORY MEMORY SPARE VOLUME SPARE AFTER PACKING 65535 KB 11820 KB 11820 KB BUAR1 4020 KB BUAR2 3136 KB
DEVICE BOARDS NUMBER OF BPOS BOARDID INDIVIDUALS SERVICE STATE 001-0-00 NOT EQUIPPED 001-0-01 NOT EQUIPPED 001-0-02 NOT EQUIPPED 001-0-03 NOT EQUIPPED 001-0-10 102 32 ACTIVE 001-0-20 57 32 ACTIVE 001-0-30 87 16 ACTIVE 001-0-32 87 16 ACTIVE 001-0-40 87 16 ACTIVE 001-0-42 87 16 ACTIVE 001-0-50 NOT EQUIPPED 001-0-51 NOT EQUIPPED 001-0-52 NOT EQUIPPED 001-0-53 NOT EQUIPPED 001-0-60 106 16 ACTIVE 001-0-62 NOT EQUIPPED 001-0-63 96 1 ACTIVE 001-0-70 87 16 ACTIVE 001-0-72 31 8 PASSIVE 001-0-73 42 4 ACTIVE 001-1-00 NOT EQUIPPED 001-1-01 NOT EQUIPPED 001-1-02 NOT EQUIPPED 001-1-03 NOT EQUIPPED 001-1-10 102 32 ACTIVE 001-1-20 77 16 ACTIVE 001-1-22 77 16 PASSIVE 001-1-30 87 16 ACTIVE 001-1-32 NOT EQUIPPED 001-1-33 NOT EQUIPPED 001-1-40 NOT EQUIPPED 001-1-41 NOT EQUIPPED 001-1-42 87 16 ACTIVE 001-1-50 87 16 ACTIVE 001-1-52 87 16 ACTIVE 001-1-60 87 16 ACTIVE
001-1-62 NOT EQUIPPED 001-1-63 NOT EQUIPPED 001-1-70 77 16 ACTIVE 001-1-72 NOT EQUIPPED 001-1-73 42 4 ACTIVE
END
admiralzino (IS/IT--Management) 22 Dec 07 15:29 we've been able to resolve the problem. the REU card and PU4DC cards were replaced with RG5DC card. and the extensions started working.
but i'm still wondering what the real problem was. REU only provides ringing; TMU provides the tone and still the non working extensions had no tone - were "dead". Now after replacing the REU, they are all working. any explanation for this?
thanks for your assistance.
rgds,
The Admiral
whosrdaddy (Vendor) 22 Dec 07 16:20 could be a tension problem on the PU4DC. ----------------------------------------------------- What You See Is What You GetNever underestimate tha powah of tha google!
Card and Extension Typesthread806-1424324Share This Forum Search FAQs Links Jobs Whitepapers MVPs
Check Out Our Whitepaper Library. Click Here.PaulMcGuinness (Programmer) 6 Nov 07 11:51 Hi all,
How can I determine if a card is an Extension or Trunk card and what type of circuits (analog / digital) they are?
Is there a list of card types somewhere???
Cheers,
Paul
etompau (TechnicalUser) 6 Nov 07 13:17 ELU=Extension Line UnitTLU=Trunk Line Unit
PaulMcGuinness (Programmer) 7 Nov 07 4:12 Hi there,
Many thanks for the info.
What about these other types:-
GJUL4 ROF1375393/1 R8A TMU ROF1375335/2 R3A 31 NO INFORMATION AVAILABLENIU2 ROF 137 5396/2 R3A LPU5 ROF1314602/3 R7B 7 NO INFORMATION AVAILABLE85 CAA1122644 R4A01
Regards,
Paul
aau2 (TechnicalUser) 7 Nov 07 6:06 GJUL4 Board to connect to other Lim or GSTMU Send and receive tone, and MOH31 ELU-5 8 Digital estenssion, B+DNIU2 Board Input output, and is able to be config as CIL port.LPU5 Processor7 TLU-11 2 analog trunks85 VSU2, mesages of welcome, qeue, etc.
MD110 PRI connection to routerthread806-1420492Share This Forum Search FAQs Links Jobs Whitepapers MVPs
Check Out Our Whitepaper Library. Click Here.JosieL (TechnicalUser) 24 Oct 07 11:56 If anyone has any ideas I would appreciate it.I have an IP Call Center that is set up. I connect to the Call Center using a TLU77/1 T1 ISDN PRI connection. Problem: you can call all three numbers internally but two of the three are DID numbers and cannot be called from public. When called from PUBLIC you get a Qwest message that the number is not in service, I receive this message on all numbers that are VACANT in the switch. I receive 4 digit from the CO on my DIDsSET UP follows on both router & switch.Cisco 3825 router has the following set on itdial-peer voice 5004 voip translation-profile outgoing IPCC_IVR destination-pattern 5004 session protocol sipv2 session target ipv4:172.16.5.137 dtmf-relay sip-notify rtp-nte codec g711ulaw no vad
!dial-peer voice 7890 voip translation-profile outgoing IPCC_IVR destination-pattern 7890 session protocol sipv2 session target ipv4:172.16.5.137 dtmf-relay sip-notify rtp-nte codec g711ulaw no vad!dial-peer voice 2500 voip translation-profile outgoing IPCC_IVR destination-pattern 2500 session protocol sipv2 session target ipv4:172.16.5.137 dtmf-relay sip-notify rtp-nte codec g711ulaw no vadEricsson set up for route & numbers:Ericsson MD110<rodap:ROU=20;ROUTE DATAROU TYPE VARC VARI VARO FILTER 20 SL63 H'00000100 H'00000002 H'00000080 NO
<rocap:ROU=20;ROUTE CATEGORY DATAROU SEL TRM SERV NODG DIST DISL TRAF SIG BCAP20 0110000010000010 7 0100000010 0 30 128 01151515 211110000031 111100
<roddp:DEST=320;EXTERNAL DESTINATION ROUTE DATADEST DRN ROU CHO CUST ADC TRC SRT NUMACK PRE320 20 1505000000000000005000000 0 1 1
<adcdp:ABB=5004&7980&2500;COMMON ABBREVIATED DIALLING FACILITY DATAABB TRA CLASS NPRES5004 320D5004 12 07980 320D7980 123 02500 320D2500 12 0
dstrang1 (TechnicalUser) 24 Oct 07 14:10 Which of the three *does* work when called from external?
Is there anything different about that number as compared to the other 2 with regard to number translation when those numbers come in from the PSTN?
How is the number that does work defined in number analysis compared to the 2 that don't work?
Dave Strang
JosieL (TechnicalUser) 24 Oct 07 14:42 5004 & 7980 are valid DID numbers and are the only 2 that I need to work from external and they don't.
2500 is only a valid internal number so no need to work from externalSorry that may not have been clear.in Number Analysis all three are set up as ACMD110 VERSION=CXP1010130/2/BC12SP7/R2ANADAP;ABBREVIATED COMMON NUMBER SERIES 2500 2900 - 2950 2990 - 2999 5004 7580 - 7583 7980
dstrang1 (TechnicalUser) 24 Oct 07 16:15 I think that's your problem.You can't access a system feature from outside the system....abbreviated dial is a system feature.
Try converting those DID's into dest codes pointed at the PRI - set up just like dest code 320 (remember srt=1).
I've done this *many* times when I've needed to transit a call thru the MD to some other system (touchtone registration, emergency event server, digital modem pools, IP PBX's). You may have to play with the number formatting (use NUTRI) but only if calls fail.
Good luck,
Dave Strang
JosieL (TechnicalUser) 24 Oct 07 17:20 Could you expand more on treating them as DEST codes? I tried it and could not go through internal or external but may have done wrong.
I used a similar setup for a Diaphonics IVR and used Abbreviated numbers for the application and I can call those from outside and inside on that I used a TLU77 & ABB numbers. No Cisco router involved though <rocap:rou=39;ROUTE CATEGORY DATAROU SEL TRM SERV NODG DIST DISL TRAF SIG BCAP39 0110100010000010 7 0000000011 0 10 128 01151515 211110000031 111100rodap:ROU=39;ROUTE DATAROU TYPE VARC VARI VARO FILTER 39 SL63 H'00000100 H'00000002 H'00000090 NOEXTERNAL DESTINATION ROUTE DATADEST DRN ROU CHO CUST ADC TRC SRT NUMACK PRE380 39 1225000000000251002001000 0 1 1 COMMON ABBREVIATED DIALLING FACILITY DATAABB TRA CLASS NPRES7580 380D7580 1 0
whosrdaddy (Vendor) 25 Oct 07 3:13 JosieL, what you are trying to do is tromboning. what version do you have(CADAP;) if you have BC12 or higher, you can allow tromboning by setting ASPAC 118 to 0. another solution is to reprogram the AC's to empty acd's with a CDINI to an AC (from BC11 you can use GH for that sort of functionality)
/Daddy ----------------------------------------------------- What You See Is What You GetNever underestimate tha powah of tha google!
JosieL (TechnicalUser) 25 Oct 07 10:10 Setting ASPAP 118 made no differenceSetting up ACD group no differenceSetting up a GH group no differenceStill can't call 7980 or 5004 from external
whosrdaddy (Vendor) 25 Oct 07 10:20 try to remove the 'D' from your ABB codes.
try to make a call trace:
stuni:unit=SLP63,lim=x; (lim where PRI resides)sttsi:tri=1;/*make call*/sttse:tri=1;/* open logfile */strap:tri=1;/* close logfile */analyse logfile with signal trace interpreter (sam toolbox)if you don't have that, then past the trace here (keep it as short as possible) and explain the correct callcase ----------------------------------------------------- What You See Is What You GetNever underestimate tha powah of tha google!
JosieL (TechnicalUser) 25 Oct 07 16:18 Finally working but really had to jump through HOOPS on this one.
Took the D out of the TRA in the Abbreviated Dial, but then you could only dial from external. Internal dialing would not work so....Added a Generic Extension and put a PELPI on it to the External number and it works. It's a trunk hungry solution but it works.
Route infothread806-1407496Share This Forum Search FAQs Links Jobs Whitepapers MVPsNCCOI (IS/IT--Management)
12 Sep 07 6:37
Hi friends,
I need to know the direction of the traffic at the trunks in our routes.Incoming or outgoing or two-way? How can i verify this?Any suggestions?
Thanks in advance.
**************************************“Science may never come up with a bettercommunication system than the coffee break.”**************************************
fouesnant (TechnicalUser) 12 Sep 07 10:41 Hi NCCOI
Norammly your operator knows how much channels are set for incoming, or outgoing or bothway direction. As far as I know, the MD110/Mxone assume that channels are bothway, as soon as you have assigned a dest to them.If no dest, the system will no try to make outgoing call, and therefore only incoming call will be handled
singhbrindisi (TechnicalUser) 12 Sep 07 12:04 Hi,
If i remember correctly , RODAI is the parameter in which you can create traffic either for Incoming / outgoing or both way.... Escaping VARO or VARI makes the difference to create one way traffic...
TLU75/1 and UK central office trunkthread806-1407110
Share This
Forum Search FAQs Links Jobs Whitepapers MVPs
kkong42 (TechnicalUser)
11 Sep 07 6:43
Hi there,
Does anyone have know the parameters to use with the TLU75/1 and a standard UK 2-wire analogue trunk line.
I tried some parameters but without success... previously we used the TLU74 card and function block TL1, but TLU75 can't use TL1, only TL11 and TL25 for PSTN lines.
I am using MX-ONE TSW SP3.
Thanks a lot,kong
IPuser (TechnicalUser) 11 Sep 07 9:23
Which Standard ( UK 2-wire analogue trunk line ) would that be ?
kkong42 (TechnicalUser) 11 Sep 07 12:38
Hi
It's just your standard "central office" trunk, e.g. the dialtone as provided by BT to your house or an analogue extension port from another interworking PABX.
An FXS circuit, what you would connect a standard telephone to.
Regards,kong.
IPuser (TechnicalUser) 11 Sep 07 13:44
With Type=TL25, for Regular (non-DDI) PSTN useVARC=00000010,VARI=00000000,VARO=00001071 PTS or 0000C071 PSP
kkong42 (TechnicalUser) 11 Sep 07 16:18
Thanks, tried that, but as soon as I assign an individual to the route (ROEQI:ROU=3,TRU=2-1,EQU=002-2-10-1), I get one of the same error messages as I had before.
The TLU75 is the only traffic board in LIM2, MAG2.
CODE<ALLOP;ALARM LOG
IDENTITY: XXXXXXXXVERSION: CXP1010125/4/TSWSP03/R4A
DATE: 11SEP07 TIME: 21:16:06
CLASS: 4
12 NO CONNECTION WITH DEVICE BOARDS IN ONE MAGAZINEDATE TIME ALP NOIF EQU INF1 11SEP07 21:03:47 4 1 002-0-**-** 2
CLASS: 2
15 DEVICE BOARD FAULTY OR MISSINGDATE TIME ALP NOIF EQU BRDID11SEP07 21:03:41 3 1 002-2-10-00 76
LAST ALREI: 11SEP07, 11:38:47
END
<RODAP:ROU=3;ROUTE DATAROU TYPE VARC VARI VARO FILTER3 TL25 H'00000010 H'00000000 H'00001071 NOEND
<ROCAP:ROU=3;ROUTE CATEGORY DATAROU SEL TRM SERV NODG DIST DISL TRAF SIG BCAP3 0110000000000010 4 3100100100 0 30 10 00151515 400110000000 001100END
<ROEDP:ROU=3,TRU=ALL;ROUTE EQUIPMENT DATAROU TRU EQU IP ADDRESS SQU INDDAT CNTRL3 002-1 002-2-10-01END
IPuser (TechnicalUser) 12 Sep 07 12:19
That usually means a Faulty Card.How did you ever get the Card initiated ?CNHUI or CNBOI ?
CDINI command equivalent for IP extensionsthread806-1407482Share This Forum Search FAQs Links Jobs Whitepapers MVPs
baldanondo (TechnicalUser) 12 Sep 07 5:36 Hello,
We are trying to configure call diversion for IP extensions when calls are missed because the extensions are busy or when they have not been attended
We can't use CDINI command as we do in analog or digital extensions, how could we do it?
regards
pd: we have BC12
Mpe (TechnicalUser) 12 Sep 07 8:38 You have to use PELPI command:
Extension 251 wants a diversion on no answer to and also when busy.
pelpi:dir=251,list=1,cho=1,anspos=251,TIME=10,bsycho=3;pelpi:dir=251,list=1,cho=2,aspos=252,time=10;pelpi:dir=251,list=1,cho=3,aspos=252,time=10;mpe
baldanondo (TechnicalUser) 12 Sep 07 9:13 Hello,
Thank you for the quick answer. I've tried it and it works, the problem is that after configuring it we see in the main screen "List act 1" instead of the date and time that we saw before configuring it. Isn't it possible to have this call diversion configured without having to see it at the screen? regards
singhbrindisi (TechnicalUser) 12 Sep 07 12:07 Hi,
I think List act 1 / Profile 1 etc are stored in the text strings..
Try manipulating with KSTSC or explore somewhere there...
Cheers, ""The truth about action must be known and the truth of inaction also must be known; even so the truth about prohibited action must be known. For mysterious are the ways of action""
DEST issuethread806-1370701Share This Forum Search FAQs Links Jobs Whitepapers MVPs
Find A Job or Post a Job Opening Click Here.Option43 (TechnicalUser) 23 May 07 10:30 Hello, I have a customer who has asked if we can manipulate numbers sent to the call logger. Here is the example, user dials 1234 which is an extension on another system via a digital link. 12 is the DEST and 34 is the last 2 digits of the extension. When we look at the call logging the 12 shows as Access Code and 34 show as Dialled Digits. We need to get the 12 incorporated in the Dialled Digits. Does anyone know how to do this on a BC12 system?
Thanks
ceejay55 (TechnicalUser) 23 May 07 18:58 numtyp=EC instead of ED
bpetya (Programmer) 24 May 07 15:45
Hello!
NANSI:NUMTYP=ED,NUMSE=1200&&1299; //not 12!!RODDI:DEST=12, rou=x, adc=x, SRT=1;
Peter
Option43 (TechnicalUser) 31 May 07 16:02 Hello Peter,A big thanks for the information. Our customer has 2, 3 & 4 digit range. 2 & 3 are fine but I can't add the 4
range due to a 3 digit restriction with NUMTYP EC. Do you know of a patch number to increase this? If so I can then get intouch with Ericsson and try and obtain it.
Many thanks.
bpetya (Programmer) 5 Jun 07 14:53 Hello!
I wrote NUMTYP=ED! You will can use 5 digit to programise. And CIL will fine.
Peter
Option43 (TechnicalUser) 6 Jun 07 4:58 Hello,Appologies it was ceejay55 who mentioned EC. Can you advise ceejay55 please?
Thanks.
MD110 configurationthread806-1362202Share This Forum Search FAQs Links Jobs Whitepapers MVPs
cspectra (TechnicalUser)
30 Apr 07 10:02
I am assigned to figured out the problem with our Ericsson MD110 BC12. I know almost nothing about PBX, but I have ALEX, and could not do much with it since I am a novice in this field. The old expert left and took all document with him, I guess.In general, the voice is OK. But we got some problem dial in and out. The provider told us that they could not receive any information from our side except the called number (B-party). Besides, the CLI number they got on their test phone is the CLI they assigned to our main PBX, 999-9999-9999! They said the problem is on our side.Could anybody help me with this. Thanks
pawshman (Programmer) 1 May 07 8:26 You can set the CLI to ON or OFF,
however, it depends on what your carrier does with the calls.
If the Carrier has been instructed not to display CLI it will withold it, if they will display it, it will display the first number in the DDI range: example
DDI range is 01256 123000-1234000your extension is 3156
so your DDI number is 01256-123156
The caller will have displayed 01256-123000
cspectra (TechnicalUser) 1 May 07 10:20 Thank you for your prompt response.The problem is, according to them, the PBX never sent any B-party number out. I'd like to know how to
check and turn on this feature so that all possible call-information sould be sent out to trunk line. I am studying the PARNUM list, but not sure which one relates to this, and which command will be used to change this. Put up with me please!
dstrang1 (TechnicalUser) 1 May 07 12:00
cspectra (TechnicalUser) 1 May 07 10:20 WRIT: >Thank you for your prompt response.>The problem is, according to them, the PBX never sent any >B-party number out. I'd like to know how to check and >turn on this feature so that all possible call-information >sould be sent out to trunk line. >I am studying the PARNUM list, but not sure which one >relates to this, and which command will be used to change >this. Put up with me please!
What type of trunks do you have? If they're not ISDN or IP, you won't be sending out any calling party info anyway.
The calling extensions have to be allowed to present their internal number to the network -- enabled in the ADC parameter for the extension category info. (ADC bit 9 for analog and ADC bit 10 for digital)
You'll need to use the number translation feature and RONDI to build out the rest of the public number as it goes out to the network.
And, as stated above, your circuit (if ISDN) has to be enabled by the carrier to pass the calling party info to the rest of the network.
Good luck,
Dave Strang
cspectra (TechnicalUser) 1 May 07 16:38 dstrang1; I post wrong info; the A-number is not sent out to the destination, not the B-number. The only trunk is ISDN.There is only 1 route in the system. How many routes can we create? And I am not sure how to check for the setting of the calling extension. Could you help please. Thanks
dstrang1 (TechnicalUser) 2 May 07 15:09 To check an analog extension: EXCAP:DIR=xxxxx;
In the printout, under ADC - the last bit should be a one.
To check a digital extension: KSCAP:DIR=xxxxx;
In the printout, under ADC - the tenth bit should be a one.
The best way to find out what your switch is sending out is by monitoring the D-channel messages with a protocol analyzer.
Good luck,
Dave Strang
cspectra (TechnicalUser) 3 May 07 15:18 dstrang1. Thank you for your tips. I made it work, and the Extension number shown on the trace for call setup going out. However, it is only its extension, no PBX number.I think nobody ever set this up. Could you tell me the sequence and command to set this up. Please.
Again, thank you very much.
whosrdaddy (Vendor) 3 May 07 15:51
check your outgoing routes with RODDP:DEST=ALL;then assign prefix to the outgoing route with RONDI.
small example:
suppose we have DDI range 123 3xxx (3xxx = extension)RONDI:ROU=X,EXNOPU=2-123; the '2'-123 stands for national number. if the PBX sends out unknoxn number format, change 2 into 0 (so 0-123)
/Daddy ----------------------------------------------------- What You See Is What You GetNever underestimate tha powah of tha google!
dstrang1 (TechnicalUser) 3 May 07 15:59 You can use number conversion and route number data to build out the rest of the calling number. You can actually do it all in number conversion....
The command is :NUTRI:, the parameters you'll be concerned with are entry, cnvtyp, numtyp, and pre
Look in ALEX, Operation and Maintenance,ACS under Number Conversion for info regarding the command and the above parameters.
Good luck,
Dave Strang
whosrdaddy (Vendor) 3 May 07 17:38 small NUTRI example
suppose we have extension 3xxx series:
NUTRI:ENTRY=3,CNVTYP=1,NUMTYP=10,pre=12345;
/Daddy ----------------------------------------------------- What You See Is What You GetNever underestimate tha powah of tha google!
cspectra (TechnicalUser) 4 May 07 10:31 Thank dstrang1 and whosrdaddy. The conversion for both received B-num and sending A-num is working now. However; I am not sure what RONDI does for the number to call out? Besides, can you tell if I can make more routes with one ISDN trunk, in which all lines are tied to the existing rou?I'd like to create all routes, if neccesary, for international, nat, unknown, and subscriber; could that be possible with just one route per different destinations?
Thank you again.
dstrang1 (TechnicalUser) 4 May 07 11:26 cspectra (TechnicalUser) 4 May 07 10:31 sed: >Thank dstrang1 and whosrdaddy.
You're welcome.
>The conversion for both received B-num and sending A-num >is working now. However; I am not sure what RONDI does for >the number to call out?
In my case, I use number conversion to add the rest of the office code to the outgoing station number, and then I use RONDI to add on the area code and form the complete 10 digit national number for the calling party.
Both the NU and RO settings (RONDI and RODDI for the dest codes pointed to the route) are tied to the LCR tables and the various entries made for dialled numbers.
> Besides, can you tell if I can make more routes with one >ISDN trunk, in which all lines are tied to the existing >rou?
You'll only have one "route"......you can however, have multiple ways to to manipulate and format dialled digit strings before they are actually sent out over that route to their destination.
>I'd like to create all routes, if neccesary, for >international, nat, unknown, and subscriber; could that be >possible with just one route per different destinations?
Essentially, yes........but it can get fairly complex (an unfortunate side effect of flexibility).
You first program the "route" - the physical trunks.(RODAI, ROCAI)
Then you assign destination codes which point to that "route". (RODDI)There is a parameterin that command - ADC - within which is determined the type of calling number, called number and other interrelated info.
The dest codes are then entered in LCR as the value for "PRE" in the Fictitious Destination Table (FDT).
Then entries are made in the various LCR tables for the dialled digits according to number length, possible conflict with other dialled numbers, digits to be added, digits to be removed - and possibly be replaced with other digits, dest code to be used before sending the call out to the trunks (which determines type of called and calling number)and formatting of the dialled number (TON).
If you didn't catch on, the dialled number is formatted in both the RODDI command and the LCDDI (LCR entry) command......the entries for both should agree with each other. Some CO switches are more forgiving than others when it comes to what the number is formatted as and the actual number sent.
For example, if I format an outbound number as "national", but send only xxx-xxxx instead of xxx-xxx-xxxx, my call may be rejected because a "national" (North American Numbering Plan)number is supposed to be 10 digits.
An AT&T 5E switch won't care, a Verizon GTD5 or a Seimens WILL care.
>Thank you again.
Good luck,
Dave Strang
cspectra (TechnicalUser) 4 May 07 16:24 dstrang1 or whosrdaddy;Could you explain or help me with this.Since I want to follow your guidances, I add new DEST (2) for National call-type, and delete the old one, DEST (0).Then we cannot make the call any more, if we put it back, then the call is through. I know that we should leave it alone, but I want to know what else related to it prevents the new one to work?Thanks again.
dstrang1 (TechnicalUser) 4 May 07 17:17 First rule: If it already works, don't change it!
Second, in order to try to determine why the 2nd one didn't work, you'll need to provide the printouts for RODDP:DEST=0; and RODDP:DEST=2; to compare them.
C-ya,
Dave Strang
cspectra (TechnicalUser) 7 May 07 10:22 dstrang1 or whorsdaddy;Could you look at the data I provide below to tell what's wrong, please.I did everything you suggested and concentrated on TON=2 for national, the call is true, but the A-number did not show up correct, without the area code.
#### starting of data<ROCAP:ROU=ALL; ROUTE CATEGORY DATA
ROU SEL TRM SERV NODG DIST DISL TRAF SIG BCAP
1 7110000000000010 5 0000000011 0 30 128 00151515 111100000031 001100
END
<RODAP:ROU=ALL; ROUTE DATA
ROU TYPE VARC VARI VARO FILTER
1 SL60 H'00000300 H'10040000 H'00410000 NO
END
<RODDP:DEST=ALL; EXTERNAL DESTINATION ROUTE DATA
DEST DRN ROU CHO CUST ADC TRC SRT NUMACK PRE
0 1 0225200000000250002001110 0 2 01 1 0125200000000250001001110 0 2 02 1 0025200000000250000001110 0 2 04 1 0425200000000250004001110 0 2 0
END
<RONDP:ROU=1; ROUTE NUMBER DATA
ROU PRE ROUDIR EXNOPU EXNOPR TERAC
1 1-269 2-301 4-379
END
<ROELP; PUBLIC EXCHANGE NUMBER PER LIM DATA
LIM EXNOPU
1 2-301
END
<NADAP; NUMBER ANALYSIS DATA
TYPE OF SERIES NUMBER SERIES
EXTENSION NUMBER SERIES 1000 - 1999 3013
EXTERNAL DESTINATION CODE 0
LEAST COST ROUTING ACCESSCODE NUMBER SERIES 7
TYPE OF SERVICE CODE SERVICE CODE
EXTERNAL NUMBER LENGTH DATA
EXTERNAL NUMBER NUMBER LENGTH
PROCEED TO SEND SIGNAL DATA
EXTERNAL NUMBER POS. TYPE
CALL DISCRIMINATION DATA
EXTERNAL/INTERNAL NUMBER CAT
END
<NUTRP:CNVTYP=0; NUMBER CONVERSION DATA
ENTRY CNVTYP NUMTYP ROU TARDST PRE TRC NEWTYP CONT BCAP
HLC
269301379 0 1 9 0301379 0 2 6 0379 0 4 3 0END
<NUTRP:CNVTYP=1; NUMBER CONVERSION DATA
ENTRY CNVTYP NUMTYP ROU TARDST PRE TRC NEWTYP CONT BCAP HLC
379 1 4 301 01 1 10 379 0END
### end of data
If you need more information, let me know.Thanks
cspectra (TechnicalUser) 8 May 07 15:48 hello everybody.I restarted from no route; setup new one, new destination, new LCR code and table, new entries for number analysis; but just for TON=2 (national) as dstrang1, whosrdaddy, and ALEX recommend. However, the only thing that did not work right is the "sent A-number/connected number" option. I did as dstrang1 said, but cannot find out what went wrong. I have to cheat using the hardcode for area+office+extension.We can live with it, but the company needs that feature to be dynamic. Can some body look at the data below and give me some help.
<NADAP; NUMBER ANALYSIS DATA
TYPE OF SERIES NUMBER SERIES
EXTENSION NUMBER SERIES 1000 - 1999
EXTERNAL DESTINATION CODE 240
LEAST COST ROUTING ACCESSCODE NUMBER SERIES 0
TYPE OF SERVICE CODE SERVICE CODE
EXTERNAL NUMBER LENGTH DATA
EXTERNAL NUMBER NUMBER LENGTH
PROCEED TO SEND SIGNAL DATA
EXTERNAL NUMBER POS. TYPE
CALL DISCRIMINATION DATA
EXTERNAL/INTERNAL NUMBER CAT
END
<ROCAP:ROU=ALL; ROUTE CATEGORY DATA
ROU SEL TRM SERV NODG DIST DISL TRAF SIG BCAP
1 7110000000000010 5 0000000011 0 30 128 00151515 111100000031 001100
END
<RODAP:ROU=ALL; ROUTE DATA
ROU TYPE VARC VARI VARO FILTER
1 SL60 H'00000300 H'10040000 H'00410000 NO
END
<RODDP:DEST=ALL; EXTERNAL DESTINATION ROUTE DATA
DEST DRN ROU CHO CUST ADC TRC SRT NUMACK PRE
240 1 0225200000000250002001111 0 4 0
END
<ROELP; PUBLIC EXCHANGE NUMBER PER LIM DATA
LIM EXNOPU
1 1-269 2-301 4-379
END
<RONDP:ROU=1; ROUTE NUMBER DATA
ROU PRE ROUDIR EXNOPU EXNOPR TERAC
1 1-269 2-301
4-379
END
<?LCDDP:TAB=DNT2; LEAST COST DESTINATION DATA
NUMBER TABLE
ENTRY TRC PRE ACCT FRCT TOLL CBCS BTON TNS OSA
0240 1 0 1 111111111111111 0END
<LCDDP:TAB=FDT; LEAST COST DESTINATION DATA
FICTITIOUS DESTINATION TABLE
FRCT TZONE PRE
1 1 240END
<NUTRP; NUMBER CONVERSION DATA
ENTRY CNVTYP NUMTYP ROU TARDST PRE TRC NEWTYP CONT BCAP HLC
301379 0 2 6 01 1 10 301379 0END
<?<?KSCAP:DIR=ALL; KEY SYSTEM CATEGORY PRINT
DIR TRAF SERV CDIV ROC ITYPE TRM ADC LANG BSEC
1001 00151515 0000100000 000000000 000001 33 0 00000000010000 F 01002 00151515 0000100000 000000000 000001 28 0 00000000010000 F 0
END
dstrang1 (TechnicalUser) 9 May 07 9:57 The BTON in the LCR entry, digit 2 in ADC for the dest code (type of called number) have to agree...in your case, you want to send the dialled number out as "National" so BTON=2 and bit 2 in ADC for the dest code also =2.
The RONDP/ROELP and NUTRP entries have to do with the *calling* number.
For the NUTRI entry, you have cnvtyp and numtyp = 1 and 10 respectively. The value for ENTRY = the internal directory number, and the value for PRE will = local office code associated with the DID number.
For ex: internal number = 1001 and the local public exchange number is 555-1001 (the complete National public number is 301-555-1001).
The number conversion entry would be: NUTRI:entry=1001,cnvtyp=1,numtyp=10,pre=555;
If you have digit #3 in ADC for the dest code set as "2" (type of calling public number = national)then your entry for RONDI is RONDI:ROU=1,EXNOPU=2-301;
Thus, when ext. 1001 initiates an external call, the number presented to the public network is 301-555-1001.
As for LCR entries for the dialled numbers......it appears above that you created an entry for the dest code - that's not necessary as dest codes are not actually *dialled*.The dest code is dealt with in the FRCT parameter.
Aside from the ENT and FDT tables, your LCR entries deal with the numbers *exactly* as the user dials them, and how those digits are manipulated as they pass thru each table before they are actually sent to a particular trunk route.
FWIW, your LCR entry for FDT is correct.
Hope this helps,
Dave Strang
cspectra (TechnicalUser) 9 May 07 14:10 Dave, I changed all as you said, then make a call.The public number is 379-1001. I am wondering if the 301 will be out on the trunk, since I am not sure if the "Tracer" software utility we have here collects data from inside PBS or at the "door" to the trunk
dstrang1 (TechnicalUser) 10 May 07 11:25 cspectra (TechnicalUser) 9 May 07 14:10 sed: >Dave, I changed all as you said, then make a call.>The public number is 379-1001. I am wondering if the 301 >will be out on the trunk, since I am not sure if >the "Tracer" software utility we have here collects data >from inside PBS or at the "door" to the trunk
Place a call to your cellphone or to an external number which you know can display caller ID.
Good luck,
Dave Strang
cspectra (TechnicalUser) 10 May 07 11:33 Dave;I did many times. The number appear on the MS phone is 301-379-1000 which is the CLIP numbet that the provider set-up at their side. If I hardcode the PRE, then the EXT numbbers show correctly.Is there any other things that might prevent this? I can provide more data. Thanks
dstrang1 (TechnicalUser) 10 May 07 13:24 cspectra (TechnicalUser) 10 May 07 11:33 says:>Dave;>I did many times. The number appear on the MS phone is >301-379-1000 which is the CLIP numbet that
the provider >set-up at their side. If I hardcode the PRE, then the EXT >numbbers show correctly.
I guess the short answer is to leave it set that way - I assume that "hardcode the PRE" means you put both the area code and the office code in front of the ext in the NUTRI entry. If that method achieves the desired results and your outbound calls complete successfully, then it's not necessarily "wrong" to do it that way.
>Is there any other things that might prevent this? I can >provide more data. Thanks
Without seeing the LCR entry for the number you dialled, along with the dest code used by that entry, it's difficult to say......
Unless you know the correct signal trace & how to read the result, the only way to be sure what your MD is sending out is to monitor the D-channel with a protocol anlyzer and look at the setup message for the call. If you can't get your hands on one, ask the CO guys to show you a trace from one of your calls.
Good luck,
Dave Strang
cspectra (TechnicalUser) 14 May 07 15:10 Dave.Here are all of my settings:
CSPBX 14MAY07 13:15:52 1-0-60-04 SYSMML
<?NADAP; NUMBER ANALYSIS DATA
TYPE OF SERIES NUMBER SERIES
EXTENSION NUMBER SERIES 1000 - 1999
EXTERNAL DESTINATION CODE 240
LEAST COST ROUTING ACCESSCODE NUMBER SERIES 0
TYPE OF SERVICE CODE SERVICE CODE
EXTERNAL NUMBER LENGTH DATA
EXTERNAL NUMBER NUMBER LENGTH
PROCEED TO SEND SIGNAL DATA
EXTERNAL NUMBER POS. TYPE
CALL DISCRIMINATION DATA
EXTERNAL/INTERNAL NUMBER CAT
END
<?LCDDP:TAB=EXT; NOT ACCEPTEDTABNOT IN RANGE<?LCDDP:EXT=NLT; NOT ACCEPTEDMISSING PARAMETERTAB<?LCDDP:TAB=DNT1; NOT ACCEPTEDENTRY NOT FOUND
<?LCDDP:TAB=DNT2; LEAST COST DESTINATION DATA
NUMBER TABLE
ENTRY TRC PRE ACCT FRCT TOLL CBCS BTON TNS OSA
0240 1 0 1 111111111111111 2END
<?LCDDP:TAB=FDT; LEAST COST DESTINATION DATA
FICTITIOUS DESTINATION TABLE
FRCT TZONE PRE
1 1 240END
<?RODDP:DEST=ALL; EXTERNAL DESTINATION ROUTE DATA
DEST DRN ROU CHO CUST ADC TRC SRT NUMACK PRE
240 1 0225000000000250002001111 0 4 0
END
<?RONDP:ROU=ALL; ROUTE NUMBER DATA
ROU PRE ROUDIR EXNOPU EXNOPR TERAC
1 1-269 2-301 4-379
END
<?ROCAP:ROU=ALL; ROUTE CATEGORY DATA
ROU SEL TRM SERV NODG DIST DISL TRAF SIG BCAP
1 7110000000000010 5 0000000011 0 30 128 00151515 111100000031 001100
END
<?RODAP:ROU=ALL; ROUTE DATA
ROU TYPE VARC VARI VARO FILTER
1 SL60 H'00000300 H'10040000 H'00410000 NO
END
<?NUTRP; NUMBER CONVERSION DATA
ENTRY CNVTYP NUMTYP ROU TARDST PRE TRC NEWTYP CONT BCAPLC
301 0 2 1 6 0100 1 10 379 0END
<?KSCAP:DIR=ALL; KEY SYSTEM CATEGORY PRINT
DIR TRAF SERV CDIV ROC ITYPE TRM ADC LANG BSEC
1001 00151515 0000100000 000000000 000001 33 0 00000000010000 F 01002 00151515 0000100000 000000000 000001 28 0 00000000010000 F 0
END
### and here is the trace
13.27.02.940 -> Outgoing Call Reference: #025 Message: SETUP Bearer Capability Coding Standard: CCITT Information transfer capability: Speech Transfer mode: Circuit mode Information transfer rate: 64 kbit/s User information layer 1 protocol: CCITT G.711 A-Law B-Channel: 7 Progress Indicator Coding Standard: CCITT standardized coding Location: Private network serving the local user Progress Description: Origination address is non ISDN Calling Party Number Type of number: National number
Numbering plan: ISDN/telephony numbering plan Presentation indicator: Presentation allowed Screening indicator: User-provided, verified and passed Digits: 3791001 Called Party Number Type of number: National number Numbering plan: ISDN/telephony numbering plan Digits: 2409100303
13.27.02.960 <- Incoming Call Reference: #025 Message: SETUP ACKNOWLEDGE B-Channel: 7
13.27.07.240 <- Incoming Call Reference: #025 Message: CALL PROCEEDING
13.27.07.340 <- Incoming Call Reference: #025 Message: ALERTING
13.27.10.480 <- Incoming Call Reference: #025 Message: CONNECT Facility Network protocol profile: 00
13.27.10.540 -> Outgoing Call Reference: #025 Message: CONNECT ACKNOWLEDGE
13.27.12.540 <- Incoming Call Reference: #025 Message: DISCONNECT Cause: Unknown Reason: 80
13.27.16.620 -> Outgoing Call Reference: #025 Message: RELEASE
13.27.16.680 <- Incoming Call Reference: #025 Message: RELEASE COMPLETE
### I hope you could recognize some mis-configuration.
Thanks.
dstrang1 (TechnicalUser) 14 May 07 16:21 cspectra (TechnicalUser) SED:>>### I hope you could recognize some mis-configuration.
>-> Outgoing> Call Reference: #025> Message: SETUP> Bearer Capability> Coding Standard: CCITT> Information transfer capability: Speech> Transfer mode: Circuit mode> Information transfer rate: 64 kbit/s > User >information layer 1 protocol: CCITT G.711 A-Law> B-Channel: 7> Progress Indicator> Coding Standard: CCITT standardized coding> Location: Private network serving the local user^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^The above line may have some significance
> Progress Description: Origination address is non ISDN> Calling Party Number> Type of number: National number> Numbering plan: ISDN/telephony numbering plan> Presentation indicator: Presentation allowed> Screening indicator: User-provided, verified and >passed> Digits: 3791001^^^^^^^^^^^^^^^^^^^^^^^^^You may need to add an NUTRI entry: (this is reference to my statement above)
NUTRI:ENTRY=100,CNVTYP=1,NUMTYP=11,PRE=379;
> Called Party Number> Type of number: National number> Numbering plan: ISDN/telephony numbering plan> Digits: 2409100303^^^^^^^^^^^^^^^^^^^^^^^^^
Is this the number you meant to dial??
I see that your DEST code is 240 and your LCR entry is 0240,
Is the number your are trying to dial 240-910-0303?If this is correct, then your call likely is failing because you've formatted the calling number as "National" but are still sending ony 7 digits.
You could also build your calling line info all in NUTRI:NUTRI:ENTRY=100,CNVTYP=1,NUMTYP=10,PRE=301379;
You'll have to end the existing entry for 100 (NUTRE:ENTRY=100;)
Good Luck,
Dave Strang
Checking for extensionsthread806-1363508Share This Forum Search FAQs Links Jobs Whitepapers MVPs
dgsmith80 (MIS)
3 May 07 6:04
Hello,
I was after some help with commands on the Ericsson, I am a Realitis trained engineer, but I have recently taken over the support of 4 or 5 sites running Ericsson.
I have been asked to find out how many digital lines we have available at one of the sites, and how to change the time. I used ALEX to find the command for changing time and date, that has worked fine, but I can't seem to figure out how to list extensions, and how to determine which is Analogue and which is Digital etc.
Any help suggestions welcome.
ThanksDave
Mpe (TechnicalUser) 3 May 07 6:14
Simplest way to do it is to use command:SYECP;
With this command you get a overview of the the system.Broken down to amount of: Analouge, digital etc....
Mpe
dstrang1 (TechnicalUser) 3 May 07 9:28
If you want to know available capacity WRT licenses use command: LIDAP;
If you want to know how many available ports there are for digital or analog phones:
SYEVP:TYPE=EL6; for analogSYEVP:TYPE=KL1; for digital
If you want to know how many directory numbers you have available: SUVIP:NUMTYP=EX;
If you want to know how many of each type you have already assigned in the system: SYECP;
Good luck,
Dave Strang
dgsmith80 (MIS) 8 May 07 9:59
Thanks for those commands guys, but I am not too sure how to read the output...
SYECP;
SYSTEM EQUIPMENT CONFIGURATION
INITIATED LINE INDIVIDUALS IN THE SYSTEM
INTERNAL LINES: ANALOG DIGITAL 50 CAS POTS ITS OPERATOR 1 DATA DUAL
PUBLIC LINES: ANALOGUE 1 DIGITAL 30 ISDN S0 ISDN S2M
PRIVATE LINES: ANALOGUE DIGITAL APNSS DPNSS ISDN S0 ISDN S2M
<syevp:type=el6;SYSTEM EQUIPMENT VACANCIES
EQU BOARDID 001-0-62-08 87 001-0-62-09 87 001-0-62-10 87 001-0-62-11 87 001-0-62-12 87 001-0-62-13 87 001-0-62-14 87
<SYEVP:TYPE=KL1;SYSTEM EQUIPMENT VACANCIES
EQU BOARDID 001-1-60-03 31 001-1-60-05 31 001-1-60-06 31 001-1-60-07 31 001-0-12-04 59
So how many digital extensions do I have spare?
pawshman (Programmer) 8 May 07 10:17
Dave,
BPOS=
1-0-60. ONE CARD, has up to 16 ports on it
EQU=
1-0-60-00. ONE PORT or equipment positions
in the print out,
every EQU is a SPARE/UNUSED equipment/port positionor in ISDX speak PAD
dgsmith80 (MIS) 14 May 07 4:50
Thank you Pawshman, that is excellent. Being an old Realitis user it is similar in the extension card usage of the card shelf ID then the port on that card being the channel.
So from my post I have 7 digital channels, and 5 analogue channels.
Now all I need to figure out is how to list the physical extension numbers that are spare, and how to assign an extension to a channel.
NCCOI (IS/IT--Management) 14 May 07 7:13
suvip:numtyp=ex,format=list;will provide a list of all your free, unused extension numbers.
ksexi:dir=xxxx,equ=x-x-xx-xx,cat=x,itype=xx;is used to assign a new digital extension, whereequ is your free digital equipment cat is the common category code,itype is a code for the type of telephone you use, i.e. itype=19 is used for a Vox Dialog 3212
extei:dir=xxxx,equ=x-x-xx-xx,cat=x,type=el6;is used to assign an new analogue extension, whereequ is your free analogue equipmentcat is the common category codetype=el6 is used to define it's a analogue extension
pawshman (Programmer) 14 May 07 9:50 Dave,
pleasure, and like NCCOI said :)
New Extension problemthread806-1362109Share This Forum Search FAQs Links Jobs Whitepapers MVPs
Tek-Tips Forums is Member Supported. Click Here to donate.sagetarious1977 (IS/IT--Management) 30 Apr 07 3:12 Hi,
I have an ERICSSON MD 110 PABX, I created a new extension properly but after several seconds when I want to dial it, I got CONGESTION, when I tried to delete the extension, I got a message told me that the extension is busy and I can't delete this extension.What can I do?
Thanks & regards
thedayaftertomorrow (TechnicalUser) 30 Apr 07 4:02 Hi,delete extension RFPUI:UNIT=DER,LIM=X;EXTEE:DIR=XXXX; or KSEXE:DIR=XXXX;
Best Regards
sagetarious1977 (IS/IT--Management) 30 Apr 07 4:39 Hi,
Thanks for your help, but it didn't work either.
Regards.
fouesnant (TechnicalUser) 30 Apr 07 5:14 Hi
poste the result of the commandSUSIP:DIR=XXXX;SUDIP:DIR+XXXX;
fouesnant (TechnicalUser) 30 Apr 07 5:15 sorry wrong typing
SUSIP:DIR=xxxx;
and
SUDIP:DIR=xxxx;
sagetarious1977 (IS/IT--Management) 30 Apr 07 5:35 HiNow I began to face a new problem. I can't increase my LICENSES of creating new extensions. I already have 48 licenses for creating digital extensions and I used only 8 of them, if I want to add another on by using (RFPUI:LIM=1,UNIT=LISH;) it became 7 and the last extension that I made will be deleted.I don't know what's the problem?
sagetarious1977 (IS/IT--Management) 30 Apr 07 6:17 This is the result of the SUDIP: and the extension that I want to delete is 167
<SUDIP:DIR=167; DIRECTORY INFORMATION AT 14:14:29 30APR07
DIRECTORY NUMBER : 167 TYPE OF DIRECTORY N NAME : EXT. 167
EXTENSION TERMINAL DATA
EQU TERMD ADN CALALT TIMER
1-0-30-10 0026 1 0
EXTENSION DIRECTORY CATEGORIES
CAT TRAF SERV CDIV ROC TRM ADC CUST LANG B SEC MCOST
4 01010415 0000120000 010130000 000001 0 00000000010000 F 0 -
DIGITAL EXTENSION FUNCTION KEY DATA
KEY KTYPE FCN VALUE DIG
00 PGM01 FCN CAB02 FCN CAD03 FCN TNS09 ODN 16710 ODN 16711 ODN 16713 FCN TNS14 FCN TNS
GROUP DATA
DIVERSION DATA
PAGING DATA
END
<
thedayaftertomorrow (TechnicalUser) 30 Apr 07 9:23 Hi RFPUI:UNIT=KLP1T,LIM=1;RFPUI:UNIT=KLP1D,LIM=1;afterKSEXE:DIR=167;
Hunting group with external extensionthread806-1667016Share This Forum Search FAQs Links Jobs Whitepapers MVPs
Find A Job or Post a Job Opening Click Here.tono7 (IS/IT--Management) 17 Nov 11 4:18 Hello!I try to create a hunting group with 1 internal extension and 1 external extension so:
<ghdap:grp=47777;GROUP HUNTING DATA47730 47731
pelpi:dir=47730,anspos=0652907079,cho=1,time=30;
It does not work,Any ideas?
Thanks!
parnum (TechnicalUser) 17 Nov 11 4:33
Hunt group is internal only, will not ever work
best parnum
doktor (IS/IT--Management) 17 Nov 11 5:53 You can do like this:
pelpi:dir=47777,anspos=47730,cho=1,time=20;pelpi:dir=47777,anspos=47731,cho=2,time=20;pelpi:dir=47777,anspos=0652907079,cho=3,time=30; ///doktorhttp://www.kandu.dk/spg153996.aspx
tono7 (IS/IT--Management) 17 Nov 11 5:56 Hunt group is internal only, but maybe using CDINI, PELPI, GEPEI...
tono7 (IS/IT--Management) 17 Nov 11 10:24 Thanks Doctorpelpi:dir=47777,anspos=47730,cho=1,time=20;pelpi:dir=47777,anspos=47731,cho=2,time=20;pelpi:dir=47777,anspos=0652907079,cho=3,time=30;
Thus the extension 47730 receives all calls and what we need is a call for each extension
parnum (TechnicalUser) 17 Nov 11 12:59
Looks like you need mobile extension if you want internal and external to both ring
best parnum
doktor (IS/IT--Management) 17 Nov 11 15:48 Yes. Listen to parnum. That is the right way. Otherwise you will have ringing on the 3 numbers -one by one - not like in a group. ///doktorhttp://www.kandu.dk/spg153996.aspx
Satellite1900 (TechnicalUser) 20 Jan 12 4:15 try,PELCS:DIR=47730,NPRES=2,SERV=11; \Satellite1900
Blocking internal extension to internal extensionthread806-1358571Share This Forum Search FAQs Links Jobs Whitepapers MVPs
JosieL (TechnicalUser)
19 Apr 07 10:50
Hi, we currently are using the MD110 BC12SP7.Our jail has a few cellpod areas with phones installed for inmates to use for court calls. I need to block these phones so that they can only dial specific numbers internally, blocking access to external lines is not a problem that is done. But some inmates have figured out how to dial certain internal extensions and then dial from there when it hits voicemail, they still don't get external but they dial other extensions who don't want calls from inmates. So I want to put tighter rescritions on these phones so that they can only dial only specific extensions.
Any information would be helpful Thanks
dstrang1 (TechnicalUser) 19 Apr 07 11:45 You should be able do this in the traffic matrix.....if the inmate extensions have their own category, you can change the last two digits of the traff parameter to a matrix value "A" for which the "B" value of the last 2 digits in the traf for the admin phones is 0.
Print out the traffic matrix -- TCMAP:CON=T;
The "A" column goes down the left side and B goes across......for any particular "A" value (the A party), if you go across, the extension with that "A" value can only initiate a call towards another device for which there is a 1 under the "B" value of the called device (the B-party).
It's really more complicated to explain than it is to do.
For ex:Assign all the inmates to a category with the last 2 digits of traf set to 01.
Then sssign all the internal numbers that you don't want inmates to dial to a cat that has the last 2 digits of traf set to any value other than 1 or 15.
Unless you already do alot with your traffic matrix, chances are that for your system when the matrix is printed out, for A=1 there will be zero's all the way across except for B=15. (Matrix value 15 is wide open by default.)
Good luck,
Dave Strang
singhbrindisi (TechnicalUser) 22 Apr 07 14:31 Hi,
I had absoultely similar situation few years back... As dave advised initiate cat X with all matrix blocked...
In my situation i had them calling to a designated operator, with no access to any internal extn , also they can't speak with each other as they had different customer groups.. there extn series was choosed with no relation to DID series... etc etc.. tried all sort of methods...
TRAFFIC GROUP MATRIX DATACON = T BA 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 0 0 1 1 1 1 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 3 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 4 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 5 1 1 1 1 1 1 0 1 1 1 1 1 1 1 1 1 6 1 1 1 1 1 0 0 1 1 1 1 1 1 1 1 1 7 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 8 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 9 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 110 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 111 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 112 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 113 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 114 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 115 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1CON = C BA 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 0 1 1 1 1 0 0 0 0 0 0 0 0 0 0 1 2 0 1 1 1 1 0 0 0 0 0 0 0 0 0 0 1 3 0 1 1 1 1 0 0 0 0 0 0 0 0 0 0 1 4 0 1 1 1 1 1 1 0 0 1 0 0 0 0 0 1 5 0 0 0 0 1 1 1 0 0 0 0 0 0 0 0 1 6 0 0 0 0 1 1 1 0 0 0 0 0 0 0 0 1 7 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 8 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 9 0 1 1 1 1 0 0 0 0 1 0 0 0 0 0 110 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 111 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 112 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 113 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 114 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 115 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1END</****** END OF PRINT ******/
<GEDIP:DIR=ALL;DIRECTORY NUMBER PROFILEDIR LIM CSP CUST LANG MCOST BSEC4901 1 2 1 0 - 04902 1 2 2 0 - 04903 1 2 3 0 - 04904 1 2 4 0 - 04905 1 2 5 0 - 04906 1 2 6 0 - 04907 1 2 7 0 - 04908 1 2 8 0 - 04909 1 2 9 0 - 0
EXTERNAL NUMBER POS. TYPECALL DISCRIMINATION DATA EXTERNAL/INTERNAL NUMBER CAT 4901 11 1 4902 11 1 4903 11 1 4904 11 1 4905 11 1 4906 11 1 4907 11 1 4908 11 1 4909 11 1 4921 11 1 4922 11 1 4923 11 1 4924 11 1 4925 11 1 4926 11 1
Cheers, ""The truth about action must be known and the truth of inaction also must be known; even so the truth about prohibited action must be known. For mysterious are the ways of action""
rfpui (TechnicalUser) 22 Apr 07 16:03 To singhbrindisi please read
thread806-898504: For all MD110 PBX Forum members ----------------------------------If anything can go wrong, it will.(Murphy's Law)
JosieL (TechnicalUser) 23 Apr 07 9:00 Thanks, I am working it through the Matrix and just have a few things to tweak. Plus this is helping to solve some extension payphones we are using too.
Music on Hold on analog extensionthread806-1671578Share This Forum Search FAQs Links Jobs Whitepapers MVPs
denicvne (TechnicalUser) 11 Jan 12 13:09 Is it possible to stop MOH service on several analog extension?What are parametars?
pixelix (TechnicalUser) 12 Jan 12 5:25 racee:dir=XXX
adminpabx (TechnicalUser) 12 Jan 12 6:46 Hi !So far havn't heard of anything like that. But there is a parameter for both Analog and Digital to stop MoH Aspac:parnum=154,parval=0;N.B. If you want to increase the parval value by 1 or 2, have to pull out TMU and re insert.
whosrdaddy (Vendor) 12 Jan 12 14:08 devicne, what PBX version are we talking about?
if you have TSW (BC13) or TSE then the advise from pixelix is correct.
/Daddy ----------------------------------------------------- What You See Is What You GetNever underestimate tha powah of tha google!
denicvne (TechnicalUser) 13 Jan 12 12:46 TSW (BC13)