medical vacuum systems: lubricated vane - allied ... · general product specification the...
TRANSCRIPT
Product Specification
GENERAL The Chemetron® medical vacuum system is designed to
create a suction system to remove unwanted fluids or
gases from hospital/laboratory working areas. The
medical vacuum system package is compliant with the
NFPA 99 requirements for medical vacuum. Note that
larger systems are shipped on 2 or more skids and require
connection of clearly labeled wiring and piping between
skids once they are mounted on-site.
MEDICAL VACUUM SYSTEM The package shall include multiple vacuum pumps and
associated equipment, one ASME tank and one medical
control panel. Each pump is factory piped to a common
intake manifold. The system shall be completely tested
prior to shipment. Vibration isolation pads are included
with the system.
ROTARY VANE VACUUM PUMP The medical vacuum pumps shall be of the rotary vane air
cooled design, and manufactured in the USA. Each
vacuum pump shall be direct-driven through a shaft
coupling by a TEFC electric motor. Belt drives shall not
be permitted. Each vacuum pump shall be air cooled and
have absolutely no water requirements. Each vacuum
pump shall have an end (ultimate) vacuum of 29.3" Hg
(15 torr). Lubrication shall be provided by an integral,
fully recirculating oil supply that is filtered by an
automotive-type, spin-on oil filter. Non-recirculating
(once-through) or partial recirculating oil supply systems
shall not be permitted. Each vacuum pump shall be
capable of operation with standard SAE 30 weight oil.
The oil separation systems shall be integral and shall
consist of no less than three stages of internally installed
oil and smoke eliminators through which the exhaust gas
stream must pass. This system shall consist of bulk
separation, oil mist elimination, and smoke elimination,
and shall be capable of removing 99.9+ percent of all oil
and smoke particles from the exhaust gas stream. Each
vacuum pump shall include a built-in anti-suck-back
valve, mounted at the pump inlet, and three sliding vanes.
Each vacuum pump shall be equipped with a 10 micron
inlet filter for removal of particulates. The vacuum
pumps shall be mounted on vibration isolators.
MOTOR The motor is continuous duty, NEMA rated, C-face,
TEFC, suitable for 208-230, or 460V, 3 phase, 60 hertz
electrical operation.
AIR RECEIVER The system shall include an ASME rated air receiver
rated for 200 psi MAWP. The tank shall be equipped with
a vacuum gauge, block and by-pass valves, and a manual
drain.
CONTROL PANEL The system shall include a UL listed control panel in a
NEMA 12 enclosure with the following accessories for
each pump: externally operable disconnect, magnetic
starter with 3-leg overload protection, Hand/Off/Auto
lighted selector switch, minimum run timer to prevent
short cycling of the pump, and hour meter.
Standard features shall also include a main power on
light, timed lead/lag pump alternation, a reserve pump-in-
use alarm with visual and audible indications, and duplex
control circuit transformers with fused primary and
secondary protection. All alarms shall have dry contacts
on a labeled terminal strip for remote alarm monitoring,
and an acknowledge pushbutton for horn silencing. The
lag vacuum pump shall be able to start automatically if
the lead vacuum pump fails to operate.
AVAILABLE OPTIONS
High discharge air temperature shutdown alarm with
visual and audible indicators and dry contacts
Oil temperature gauges
Internal tank lining for corrosion resistance
Tank sight gauge
Medical Vacuum Systems:
Lubricated Vane
Medical Vacuum Systems:
Lubricated Vane
Product Specification
Duplex Lubricated Vane
Tankmount
1 - 10 hp
208V 230V 460V
DLV010-80T 1 4 4 80 2,546 70 10 10 6 730
DLV015-80T 1-1/2 7 7 80 3,819 70 11 11 7 730
DLV020-80T 2 11 11 80 5,092 70 14 14 8 835
DLV030-80T 3 17 17 80 7,638 70 19 18 10 894
DLV050-120T1 5 26 26 120 12,730 71 30 28 15 1,049
DLV050-120T2 5 38 38 120 12,730 71 35 32 16 1,077
DLV075-200T 7-1/2 52 52 200 19,095 79 44 43 23 1,727
DLV100-200T 10 77 77 200 25,460 81 55 53 28 2,165
No tes : 1 - HP and NFP A Sys tem Capacity is s ho wn with o ne o r mo re pumps in res erve per NFP A 99
2 - BTU/HR Levels a re s ho wn with res erve pump(s ) o n s tandby
3 - dB(A) is s ho wn with o ne pump in res erve per NFP A99
TANK
SIZEBTU/HR2 dB(A)3
LEVEL
SYSTEM
WEIGHT
SYSTEM F.L.A.
Duplex Lubricated Vane
NFPA
System
Capacity
SCFM @
19" Hg
Each
MODEL HP1
Product Specification
Medical Vacuum Systems:
Lubricated Vane
Duplex Lubricated Vane
Vertical
1 - 3 hp
Product Specification
Medical Vacuum Systems:
Lubricated Vane
Duplex Lubricated Vane
Vertical
5 hp
Product Specification
Medical Vacuum Systems:
Lubricated Vane
Duplex Lubricated Vane
Basemount
7-1/2 - 25 hp
Product Specification
Medical Vacuum Systems:
Lubricated Vane
Triplex Lubricated Vane
Basemount
5 - 10 hp
Product Specification
Medical Vacuum Systems:
Lubricated Vane
Triplex Lubricated Vane
Basemount
15 - 25 hp
Product Specification
Medical Vacuum Systems:
Lubricated Vane
Quad Lubricated Vane
Basemount
5 - 25 hp
All specifications are nominal and subject
to change without notice.
Warranty: See Allied Statement of Warranties for details.
© 2009 Allied Healthcare Products, Inc.®
1720 Sublette Avenue
St. Louis, MO 63110 USA
314/771-2400
800/444-3954 www.alliedhpi.com
ISO 13485: 2003
Construction Customer Service
USA: 800/444-3960
FAX: 314/771-7537
Canada/Mexico: 800/446-0552
FAX: 800/246-6201
International: 314/268-1683
FAX: 314/771-5183
Medical Vacuum Systems: Lubricated Vane
Form 62-00-3800 June 2009
Product Specification