INFINITY ANALYZE Software Quick Start Guide - v4.0.2Thank you for purchasing a Lumenera INFINITY camera, which includes two complete sofrware packages - INFINITY CAPTURE andII{FINITY ANALYZE.

INFINITY CAPTURE is an intuilive user interface that contains all of the basic batu.es needed to conlrol lhe camera and capture imag€s.lNFlNlTY ANALYZE expands on the functionality of INFINITY CAPTURE, adding complete imaOe analysis funciions sucfi as m€asu.ement,annoialion, tiling, archiving and advanced image processing.

This guide will help you get started using INFINITY ANALYZE. For instructions on how to install your INFINITYcamera and software please refer to the INFINITY Camera and Software lnstallation Guide.

1) Control Panel:

Global White BalanceRemove the sample from the light path and click on the White Balance icon. This produces a global white balance.

Area White BalanceWith the sample in the light path click on the Area WB icon. The cursor is transformed into a dropper. Click on a whitearea of the sample. This produces an area white balance.

CaptureTo capture an image select the Capture icon in the Capture Controlsection, or double click on the live image. In orderto produce a preview, ensure that the Preview Captured lnage box, located under the Capture Options section,is checked.

Field GroupThe field group and imaging control menus can be toggled by clicking on the lmaging Controlicon at the top of thecontrol panel. The field group is a thumbnailwork space that stores the captured images in cached memory.

To F i I elF ield G rou pl BothChoose where captured images are stored by selecting File to have them automatically saved to a local drive,Field Group to save in the field group or Both. The directory where images will be saved is shown in the areaimmediately below, and can be changed at any time by clicking on the icon next to the disk address.

Auto Increment File NameSelect the File Path box to increment saved files. You must select the icon next to the Field Path box to select aninitialfile name. Once this is done each capture file name is automatically incremented by one.

Ctrhd Pdlcl

@ ;i; ffi Im.(irs cs*rd

Ca9twa Control

Firld Gu+

v I ImgrgCfitoi

2) Galibration, Measurement and Annotation

Calibration (captured image only)Prior io p€ricrming calibtation, tum off the ft fo rv,irdow oplion to display the image without sub sampling. To perform a calibration, plac€ a stagemicrometer in the field of view. Select the calibralion icon which tansiorms the cursor into a crosshair. Left click once to st rrt the calibration,drag the cutsor over the known distance then lefl click again to complete lhe calibration. This produces a Mrbrorreter Calibntion dialogbox.Input the length you have measured across lhe stage micromebr and the magnifcation on your microscope optics. Choose a linearmeasurement unit and input it€ conversion to miqons (i.e. inch (in) = 25,400 mic.ons). Press OK to complete the calibration. ElgSeIqEj The.SlF file brnat retains all calibration and measurem€nt information. Pl€ase €nsure files are saved in this format if future measurements are to b€EKEN.

i n - a li ra i Figure 2: Fit to Window icon

fFmo'? R!ri{ fE'-l

f .\.4&E@-l f FqE"eqdrjily' a*orve [i1 Couc

,,3) via.oon i.1) via*or

C4t6e Optknr

Asadng

0 1 0 z o r o e5r&aryFrg

or az os { : tl n

OF& OFi.ldGHr Ogodr

E:\BrirVak\Smole lmmi | |. r:J

EC!tr$c fll lidd ot vis

Pler*iew ca4uad inagc

flvaigmmruocgmilArro iurilsr tk ffirE

ICSwc16.bi ffefomd

I us Ertsted Erpare

o i o : ( * l 8 g 8 s . l

Figure 3: MicrometerCalibration Dialog Box

Saving CalibrationsMuftiple calibrations can be saved in the Capfure Controlsection as seen in Figure 1. To save a calibrationsefect the Add icon, which produces a Preset Name dialog box. Choose a name such as the optic youcalibrated against (10x, 20x etc...) the select OK to save the calibration information. When previewingprior to capture you must choose the applicable calibration in the drop down box above the Add icon.

F i n d i n g Cal i bratio n I nform ati onCalibration data for the live preview and captured images is found on the bottom right hand corner of theapplication window. The third item from the right is the current calibration setting.

Figure 1: Gapture Control

Figure 4: Calibration Data

Lumenera Corporation . 7 Capella Court, Ottawa, ON, Canada K2E 847 . (t) 1.613.736.4077 . (0 1.613.736.4071 . www.lumenera.com

@2007 Lumenera Corporation, all rights reserved.Design, features, and specifications are subject to change without notice.

01292007

MeasurementMeasurements may be performed on any captured images once lNFlNlW ANALYZE has been calibrated.Left cfick a Measuremenf icon transforming the cursor to a crosshair, choose your starting point, drag yourmouse to the end of you measurement and left click a second time to end the measurement.

i fr- #@ hh{,,a,}.bf E *&ffi#FiguF 5i earuBment Box

Eadr time a measurement is prcduc€d an entry ls creatgd In th€ iifeasurpr?gnt Box bund at the botlom of the soffi rare. Send this informationto Exc€l by opening the Excel sof,ivare, clicking on the data in the lrsasu.omert Bo(, dragging it to the Exc€l softt €re tab on your WindowaTaskber, end dropplng it.

t,edsure Opf'ons,ireasu|p Optbns can b€ found in the tlroas./re drcp dolm menu. Here users can solect lh€ numb€r of d€cinal plac€s and oth€r m€asuaemontoplions such 9s nomenclaturc.

ltorsure Coro.sTo change ihe cofor or slze of measursm€nt8, sslsc{ Or€rlay Color ot Oveday Sizp ln tE View d.op dodn menu.

AnnotationTo place an annotation on your image select the annotation icon. This greys out the measurement icons and allows access tothe annotation icons. Once the annotation section is selected, double click on the annotation to bring up a dialog box whichallows changes to its font, size and shape. Note that annotations and measurements may not be performed at the same time.

q-l

To go back to measurements, click the annotation icon a second time.

Burning Annotations and MeasurementsSefect the Burn Annotation icon to permanently add measurements and annotations to an image. All measurements andannotations will be lost if an image is saved without burning it first.

Removing An notations and MeasurementsMeasurements are removed using the Resef Measuremenf icon found in the measurement toolbar. Annotations are removed by selecting theDelete icon, but only when the annotation section is active. The number value for a measurement is considered an annotation and can only beremoved when annotations are active. Measurements and annotations are removed separately.

lmageWindow SizeThe size of the image window may be defined by the user. To activate this feature select the Fft to Window icon as seen in Figure 6, then theMinimize/Resfore icon in the upper right hand side of the software. To set the window size select lmage Window SEe in the View drop downmenu. To capture this section of the image uncheck the Capture Full Field of View box in the Capture Options section.

i lerl \ E F il M \ Hil lU

llr I

lhH

Figure 6: Fit to Window and Minimize/Restore lcons

3) Additional Help

The help section of your lNFlNlTY ANALYZE software contains a complete user-friendly manual that includes a detailed description of all thefeatures available.

Flash tutorials are available on the supporUdownload section of the Lumenera website at www.lumenera.com/supporUdownload.php. Thesetutorials offer an excellent opportunity to view the various functions of lNFlNlW ANALYZE.

For further assistance contact:LumeneraTechnicalSupport (613F736-4077

support@lumenera.com

Lumenera Corporation . 7 Capella Court, Oftawa, ON, Canada Y\2EBA7. (t) 1.613.736.4077. (f) 1.613.736.4071. www'|@glgB.8@

@2007 Lumenera Corporation, all rights reserved.Design, features, and specifications are subject to change without notice.

o't292007

Cdpar [tirtance ,63,50Area Perimeter Area 23+7,99

Area Perimter Perineter 184.03

Clcle :Radius ,?7,?B

INFINITY ANALYZE Software Overview

ii& dc Efr Snt

; r * f f i ; g

; : % , e € v

iQn, ' 'E E I S

n# AdF* Eftrr! [r|qr? Ifrdo."Y U*

,,., ."r, m il [iJ rfr S]lt{l:t € t g

E # e c o l l a € d 6 . h 4 d ) f r I W : i * ,O V r t r h i r X q q t * *

& @ [ fu{ r,r.;, K r.r r}

lmaging Control (toggles to Field Group)

KFIIi

$ t ^ e * i d " ' * n

LumeneraCorporat ion.7Gape| |aCourt ,ot tawa,oN,Canadal<2E8A7.( t )1.613.736.4o77.( f )1.613.736.4o71.@,

@2007 Lumenera Corporation, all rights reserved.Design, features, and specifications are subjec't to change without notice.

01292007

I-

I HLuI FRAcorI

ff .

INFINITY Gamera and Software lnstallation Guide

This guide explains the steps involved in the installation of the INFINITY software and camera, as well as system-requirements and helpful tips.

This camera is designed to operate straight out of the box, however, prior to plugging the camera into your computer youmust first install the INFINITY camera software. Failure to do so may result in the camera drivers not being operational.

System Requirements:o Windows 2000 (Service Pack 4) or XP (Service Pack2\. 600 Mhz Pentium lll or higher compatible computero Memory:256 MB min.,512 MB recommendedo USB 2.0 Port

lNFlNlry Software lnstallation:

1) To install lNFlNlTYcamera software, close all open applications and insertthe lNFlNlTYsoftware CD included withyour INFINITY camera into the CD-ROM drive. If you are upgrading your software, go to:http://wvyw.lumenera.com/supporUdownload.php to download the newest version of INFINITY camera software.The installation should start automatically. lf it does not, double-click "My Computer", double-click the CD icon, anddouble-click setup.exe

2) Read the License Agreement carefully and click "Yes".

f irrq6* k kd* S&-irltrt*kld* tu . f t *aSf f id f f ibr 4 E d H E s E d E - & 5 - d a a@*$ ' |F t t *64*H

h*medhba* f f i t f rF rp f ; : -

if f& -Fdh l rd f f4 f tk *d € l@ k F

I , t u | r r l l b I

3) Verify the destination folder in which to install theprogram and click "Next". The default destination isc\...\Lumenera Corporation\lNFlNlTY Software. Click"Browse" to change the destination folder.

4) Enter or select the name of the destination ProgramFolder for program icons.

tbkM{ * r a r y & s d d L r

&dd*mrr***hna*

3$t!ltl* **' lsr mt*Ad*

i -l';;*"fT;;-1

f - k;. " i

trrrN i{F f{fit

h d d + F s h t 4 s a e h * l d q F . € S| E r * ' 6 R f r q - l b h € *

h{st*--

ili[:fTil] f*j&l

Lumenera Corporation . 7 Capella Court, Ottawa, ON, Canada l<2EgA7. (t) 1.613.736.4077. (0 1.613.736.4071. www.lumenera.com

@2007 Lumenera Corporation, all rights reserved.Design, features, and specifications are subject to change without notice.

01292007

!t \-i

5) Click "Finish". INFINITY software installation iscomplete.

6) Please connect your INFINITY camera to thecomputer. The Found New Hardware Wizard will nowstart. Select "lnstallthe Software Automatically" andclick next.

7) The Windows Logo testing screen may now appear.Click "Continue Anyway".

t\ lhrrd.art..$ir*rtlr*rhrrldt.&r lih.p3ur,l0ersr

lrri d Flr*duhdM t qlpbegh vHly rr r.rmF tlfdh'r^ado*r;4 fl ltft cr" $d h|,n{ rcr|fr I

,--!Cfril.bE.drL ru raE- al-rbr L ccd.Or.fi d tcr."ff* -d*c i lbH{ - I rnd .b{ t--ran $-tf, n+ rlir-adatirE Gicil*El l* tr..*d. rildor t{ nlbra lial Lr

tor.auirfD I {. Lit

8) Once the INFINITY camera drivers have loaded youmay click "Finish".

9) Steps 6 through 8 will be repeated a second time. Oncethis is done installation is complete. An illuminated LEDlight on the back of your camera will confirm it isoperational. Run the application from your Start menu.

Please note: Windows will ask you to re-run these stepseach time you plug the camera into a new USB 2.0 port.

Technical Supoort

The Lumenera TechnicalAssistance Center (TAC) may be contacted by e-mail (support@lumenera.com) or by phone(613) 736-4077. Hours of operation are 9am to 5:30pm EST. Valuable information is also available online on the TACweb page htto ://www. I u menera. com/s u poorUi ndex. oh o.

Please refer to the INFINTY ANALYZE Quick Start Guide for tips on how to get started with camera control, calibrationsand measurements. The INFINITY ANALYZE overview gives a graphical location of the main features of the softwareand the FAQ sheet give answers to common questions.

Lumenera Corporation. T Capella Court, Ottawa, ON, Canada K2EBA7. (t) 1.613.736.4077. (0 1.613.736.4071. UAUgJ.U!!t91le,ru9g!

@2007 Lumenera Corporation, all rights reserved.Design, features, and specifications are subject to change without notice.

01292007

- . ) lp t * " * * -daa- rD€ . h r r * d . c

r j r *ch . t , * r * *F iwdr' * tb ' ! re* t ra .4 r r ' . t