memory card video recording system · lines), record tally output (1 line), and serial port. dc in...

Operating Instructions

Before operating this product, please read the instructions carefully and savethis manual for future use.

S0205N1035 -MPrinted in Japan

D

Memory Card Video Recording System

ENGLISHVQT0Q80-1

Model No. AG- P

Car Use only

2

WARNING:• TO REDUCE THE RISK OF FIRE OR SHOCK HAZARD, DO NOT

EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE. • TO REDUCE THE RISK OF FIRE OR SHOCK HAZARD, KEEP THIS

EQUIPMENT AWAY FROM ALL LIQUIDS. USE AND STORE ONLYIN LOCATIONS WHICH ARE NOT EXPOSED TO THE RISK OFDRIPPING OR SPLASHING LIQUIDS, AND DO NOT PLACE ANYLIQUID CONTAINERS ON TOP OF THE EQUIPMENT.

CAUTION:TO REDUCE THE RISK OF FIRE OR SHOCK HAZARD ANDANNOYING INTERFERENCE, USE THE RECOMMENDEDACCESSORIES ONLY.

indicates safety information.

3

CAUTION:In order to maintain adequate ventilation, do not install or place thisunit in a book case, built-in cabinet or any other confined space.To prevent risk of electric shock or fire hazard due to overheating,ensure that curtains and any other materials do not obstruct theventilation.

FCC Note:This equipment has been tested and found to comply with the limits for aclass A digital device, pursuant to Part 15 of the FCC Rules. These limitsare designed to provide reasonable protection against harmfulinterference when the equipment is operated in a commercialenvironment. This equipment generates, uses, and can radiate radiofrequency energy, and if not installed and used in accordance with theinstruction manual, may cause harmful interference to radiocommunications. Operation of this equipment in a residential area islikely to cause harmful interference in which case the user will berequired to correct the interference at his own expense.Warning: To assure continued FCC emission limit compliance, the usermust only use shielded interface cables when connecting to externalunits. Also, any unauthorized changes or modifications to this equipmentcould void the user’s authority to operate it.

• The recorder and camera are designed for use and installation in avehicle. For example, the components may be mounted on the centerconsole, in the trunk, or attached to a sun visor using a fastening holeor similar method.

• The recorder and camera installation must only be performed by aprofessional installer.

• The rating plate is on the underside of the recorder.

indicates safety information.

CAUTION:To reduce the risk of fire, the red (BATT) and white (SIGNAL) wiresof the power cable must be connected via fuses (5 A – 20 A) havingUL Listing (see page 12).

IMPORTANT SAFETY INSTRUCTIONS

4

(1) Read these instructions.

(2) Keep these instructions.

(3) Heed all warnings.

(4) Follow all instructions.

(5) Do not use this equipment near water.

(6) Clean only with a dry cloth.

(7) Do not block any ventilation openings. Install in accordance with themanufacturer’s instructions.

(8) Do not install near any heat sources such as radiators, heat registers, stoves,or any other equipment (including amplifiers) that produce heat.

(9) Only use attachments/accessories specified by the manufacturer, and asoutlined in this manual.

(10) Refer all servicing requests to qualified service personnel. Servicing isrequired when the equipment has been damaged in any way, such asdamage to the power supply cord or plug, liquid being spilled on or objectshave fallen into the equipment, the equipment has been exposed to rain ormoisture and does not operate normally, or has been dropped.

5

ContentsIMPORTANT SAFETY INSTRUCTIONS ..................................................4

Features....................................................................................................6

Configuration and included accessories ..............................................6

Options .....................................................................................................6

Before use ................................................................................................6

Control reference guide ..........................................................................8

Connections ...........................................................................................12

P2 card insertion and removal .............................................................14

Recording and stopping .......................................................................16

Camera operation ..................................................................................19

LEDs and recorder status .....................................................................20

Notes on handling .................................................................................21

Factory default settings ........................................................................23

Connector signals .................................................................................29

Troubleshooting ....................................................................................32

GPL .........................................................................................................36

LGPL .......................................................................................................39

OpenSSL License ..................................................................................43

Blowfish License ...................................................................................44

DES License ...........................................................................................44

Specifications ........................................................................................45

LIMITED WARRANTY ............................................................................47

Information on software for this product• Included with this product is software licensed under the GNU General Public License

(GPL) and GNU Lesser General Public License (LGPL), and users are hereby informedthat they have the right to obtain, change and redistribute the source codes of thissoftware. Details on GPL and LGPL can be found in the GPL and LGPL sections of thismanual.To obtain the source codes, go to the following home page.http://panasonic.biz/sav/The manufacturer asks users to refrain from directing inquiries concerning the sourcecodes they have obtained and other details to its representatives.

• Included with this product is software licensed under the OpenSSL License. Details onthe OpenSSL License can be found in the OpenSSL License section of this manual.

• Included with this product is software licensed under the Blowfish License. Details onthe Blowfish License can be found in the Blowfish License section of this manual.

• Included with this product is software licensed under the DES License. Details on theDES License can be found in the DES License section of this manual.

6

FeaturesVideo recorder with longrecording capabilityThe recorder uses memory cardsidentified by the P2 logo, such asthe separately available AJ-P2C002SG. (This type of card iscalled a "P2 card" in this manual.)For example, when two 4-gigabyteP2 cards are inserted, availablerecording time is up to 32 hours atthe 512 kbps rate setting.

Wide-angle, high-sensitivitycamera with IR functionThe IR capable camera improvesthe quality of images recorded atnight. The wide angle lens ensuresthat a wider area is covered.

File recordingVideo and audio files are recordedon the P2 card using a compressedformat (MPEG4 and G.726). In addition, meta data such asrecording date and time, recordingtrigger and other information canalso be recorded.

File playback and archivingRecorded files can be played backon a desktop computer. Recorded fi les can also beuploaded to an archival server via aLAN based network. (A specifiedapplication software running on acomputer is required.)

Configuration and included accessoriesThis product consists of a recorder, camera, and the following accessories.

Power cable .......................................1Camera cable ....................................1External trigger cable.........................1LAN cable (crossing type)..................1Wide conversion lens (installed on the recorder)..................1P2 card (4 GB) AJ-P2C004HG..........1

USB 2.0/LAN adapter(including driver CD) ..........................1Camera mount ...................................1Key.....................................................1Recorder mount adapter(installed on the recorder)..................2

P2 card (2 GB) AJ-P2C002SG P2 card (4 GB) AJ-P2C004HG

Set the internal clockBefore using the recorder for thefirst time or after reconnecting it tothe power supply, check that thepower cable is connected correctlyand then use the Toughbook-Arbitrator Front End Software to setthe date, time, and time zone of theinternal clock.

Exclusion of liabilityPanasonic does not accept liabilityfor any problems related directly orindirectly to data loss or failure torecord video data, audio data, ormeta data, that may be due to amalfunction of recorder, camera, orP2 card.

Options

Before use

7

Before use (continued)

Be sure to perform a trialrecordingBefore any important recordingapplication, be sure to first test thesystem to confirm that video andsound are recorded properly.Checking the correct settings isespecially important when using the“backlight compensation” and “IRenabled night recording” functions.

Use with specified applicationUse only the specified applicationsoftware for recorder and camerasetup and control. This applicationsoftware runs on a computer andallows recorder and camera setupand control via a networkconnection. For information on howto obtain the application software,consult the supplier of this product.In this manual, the applicationsoftware is referred to as the“Toughbook-Arbitrator Front EndSoftware”.

Finding related informationIn this manual, the format “see page00” is used to indicate pages withrelevant information.

Compatible memory cardsOnly P2 cards identified by the P2logo can be used with the recorder.

Never remove the P2 cardwhile it is being accessedIn some rare cases, the P2 card slotmay become inoperative. When thisis detected, the recorderautomatically restarts itself.

Before disconnecting thepower cable, make sure thatrecorder shutdown wasperformed properlyNever disconnect the power cable while

• In no event will Panasonic be liable forany damages, including any incidentalor consequential damages, stemmingfrom a failure to record data or fromlost settings or data.Any of the following actions canresult in problems:· Power supply to the recorder isinterrupted or impaired duringrecording, for example by startingan engine.

· A P2 card is removed duringrecording.

• This product is licensed under theMPEG-4 Visual patent portfoliolicense for the personal and non-commercial use of a consumer for(i) encoding video in compliancewith the MPEG-4 Visual Standard(“MPEG-4 Video”) and/or (i i)decoding MPEG-4 Video that wasencoded by a consumer engagedin a personal and non-commercialactivity and/or was obtained froma video provider l icensed byMPEG LA to provide MPEG-4Video. No license is granted orshall be implied for any other use.Additional information includingthat relating to promotional,internal and commercial uses andlicensing may be obtained fromMPEG LA, LLC.See http://www.mpegla.com/

the recorder is operating. In particular, ifthe power cable is disconnected duringrecording, P2 card managinginformation and data setting informationmay be lost or damaged. If the P2 cardmanaging information has beendamaged and files can no longer beread properly, you should format the P2card. This must be performed in acomputer where the P2 card driver hasbeen installed.

8

Control reference guideRecorder front panel

REC button ( )Starts recording of video and soundto a P2 card.

STOP button ( )Stops recording.

P2 card slots 1, 2Insert P2 cards here. Up to twocards can be insertedsimultaneously.

EJECT buttonServes to eject a P2 card.

REC LEDLights up during recording. If thecombined remaining recording timefor the cards inserted in the P2 cardslots 1 and 2 is less than 30minutes (see page 20), the LEDstarts to flash.

READY LEDLights up when recording ispossible on a P2 card inserted in aP2 card slot (see page 20).

BUSY LEDLights up or flashes while a P2 cardis accessed (recording or playback;see page 20).

LockServes to lock and unlock the coverof the P2 card slots.

CoverProtects the P2 card slots.

9

Control reference guide (continued)

Recorder rear panel

VIDEO IN connector(Pin jack)

This is a composite signal input.

VIDEO OUT connector(Pin jack)

This is a composite signal output.The signal from the camera cableconnector or the VIDEO INconnector can be supplied here. Forinformation on how to select thesignal, see the documentation of theToughbook-Arbitrator Front EndSoftware.

AUDIO IN 1, 2 connectors(Pin jack)These are line level signal inputs.The output signals of audiocomponents can be connectedhere. For details on the connection,see the installation manual.

MIC IN connector (Pin jack)This is a microphone level signalinput. For details on the connection,see the installation manual.

Cable clampThis clamp can be used to fastenthe video cable, audio cable,camera cable, and power cable.

LAN portThis port allows a 100BASE-TXconnection to a computer. Use thesupplied LAN cable.

Camera cable connectorUse the supplied camera cable toconnect the camera to the suppliedrecorder.

GPIO/SERIAL connectorThis connector serves as acombined trigger signal input (8lines), record tally output (1 line),and serial port.

DC IN connectorThis is the power supply connector.

Note:Do not disconnect the power cablewhile the recorder is operating. Inparticular, if the power supply isinterrupted during recording, P2card managing information and datasetting information may be lost ordamaged.

10


Recorder mount adapter

5555

187.4 (7-3/8 ")

(2-5

/32

")(2

-5/3

2 ")

30(1

-5/3

2 ")

Trunk mounting holes

These holes are used to mount therecorder in the trunk.For details, see the installationmanual.

Spaces for center consolemounting holes

In these spaces the holes can bemade to mount the recorder on thecenter console.For details, see the installationmanual.

11


Camera front, rear, and top

REC LEDLights up during recording.The LED starts to flash when thecombined remaining recording timefor the cards inserted in the P2 cardslots 1 and 2 is less than 30minutes (see page 20). The LEDcan also be permanently turned offusing a Toughbook-Arbitrator FrontEnd Software setting. For details onthe setting procedure, see thedocumentation of the Toughbook-Arbitrator Front End Software.

Sun shadeProtects the lens from direct sunlight.

Wide conversion lensThe wide conversion lens enables a widerviewing angle when recording video.

Backlight compensationbuttonControls the backlight compensationfunction. Each push of the buttonswitches the function ON or OFF.

Light buttonControls the camera operationpanel illumination. Each push of thebutton switches the illumination ONor OFF.

Camera cable connectorUse the supplied camera cable toconnect the camera to the supplied

recorder.

Zoom buttonsControl the zoom function. The Wbutton serves to zoom out and theT button to zoom in.

Auto zoom buttonPressing this button causes thecamera to automatically zoom in,pause for a certain period, andzoom out. The zoom factor andpause duration can be set. Fordetails on the setting procedure,see the documentation of theToughbook-Arbitrator Front EndSoftware.

REC buttonPressing this button causes therecorder to start recording.

Camera mount holesThe supplied camera mount can beattached here.When the wide conversion lens ismounted, use the front hole (A).When the wide conversion lens isremoved, use the rear hole (B).

Notes:•Use only the wide conversion lensthat was mounted on the camerawhen delivered.

•Use only the specified cameramount posit ions to install thecamera.

BA

12

Connections

•Turn power to all components off and disconnect the power cables before makingany connections. Be sure to finish all other connections first, and then connectthe power cables last. Also refer to the connector signal diagram on page 29 andto the documentation of the components that are to be connected.

•Verify that recording is not in progress prior to disconnecting any cables from the recorder.Be sure to disconnect the power cable first, and then disconnect any other cables.

•A wrong power cable connection will lead to malfunction. Make sure that thepower cable is connected correctly.

• To reduce the risk of fire or shock hazard, installation and wiring must only beperformed by a professional installer.

• To reduce the risk of fire, the red (BATT) and white (SIGNAL) wires of thepower cable must be connected via fuses (5 A – 20 A) having UL Listing.

• The provided power cable is not for use in the engine compartment.

13

VideoInput Output

(line level) (mic level)

Audio input

Camera(supplied)

Camera cable (supplied)

LAN cable (supplied)

External trigger cable (supplied)

Power cable (supplied)

Computer(available separately)

Others: Input signal lines

White (SIGNAL): Connect the signal line via timer equipment and a fuse

Black (GND): Connect to the negative terminal of the battery

Red (BATT): Connect via a fuse to a power supply that is constantly on, regardless of ignition key ON/OFF status

White: Rec Tally output line

RS-232C: Connect to equipment with serial connectors

Black: Connect to the negative terminal of the battery

Connections (continued)

14

P2 card insertion and removal

Never open the cover or remove the P2 card while the P2 card is beingaccessed. Otherwise the data on the card may be lost or damaged, and the P2card slot may become inoperative.

Inserting a P2 card

(1) Open the cover.Insert the key into the lock andturn it clockwise by 60 degrees.

(2) Insert a P2 card into the P2card slot and push it in untilthe EJECT button pops out.

Do not push in thisdirection.

EJECT button

Insert the cardwith the P2 logofacing up.

Do not touch to avoidthe risk of injury.

Notes:•To prevent damage, do not exertundue force on the open cover.

•Do not try to turn the key furtherthan the stop position, and do notmove it unnecessarily, to preventdamage to the key and lock.

(3) Fold the protruding EJECTbutton to the right.

Note:Make sure that the EJECT buttonhas been properly positioned asillustrated above before closing thecover. Otherwise the EJECT buttonwill be damaged.

15

P2 card insertion and removal (continued)

Note:If a P2 card was removed whiledata was being accessed, files maybe corrupted. In some rare cases,the P2 card slot may becomeinoperative. If this case, the filesmust be restored by controlling therecorder from the Toughbook-Arbitrator Front End Software.When this is detected, the recorderautomatically restarts itself.

(4) Close the cover.Return the cover to its originalclosed position and press thesection marked .PUSH

When you close the cover afterinserting a P2 card, the READY LEDindicates the recorder status (see page20).

(5) Turn the key counterclockwise tolock the cover and to allowremoval of the key from the lock.

Removing a P2 card

(2) Raise the EJECT button.

(1) Open the cover(see previous page).

(3) Push the EJECT button sothat the P2 card pops out.

(4) Close the cover(see top left of this page).

(5) Turn the key counterclockwiseto lock the cover and to allowremoval of the key from the lock.

16

Recording and stopping

Recording

Recording can be started by one of thefollowing methods:•Pressing the REC button on the recorder.•Pressing the REC button on the camera.•Clicking the REC button in theToughbook-Arbitrator Front EndSoftware.

•Activating a recording start triggerfrom a device connected via theGPIO/SERIAL connector on therecorder. (A setting must first bemade with the Toughbook-Arbitrator Front End Software.)

•Setting the SIGNAL pin of the powercable connected to the DC IN connectorof the recorder to ON. (A setting mustfirst be made with the Toughbook-Arbitrator Front End Software.)

When recording starts, the prerecordingfunction operates to ensure that materialfrom a certain interval before the startpoint is included in the recording. (Fordetails on prerecording, see page 17.)The duration of this interval can be setwith the Toughbook-Arbitrator Front EndSoftware. For details, see thedocumentation of the Toughbook-Arbitrator Front End Software.Make sure that the camera cable,external trigger cable, and audio cables(available separately) as well as anyother cables are connected correctly, asdescribed in the installation manual.

Notes:•Recording can be started only ifthe READY LED on the recorder islit. If recording is not possible whenthe REC button is pressed or therecording start trigger signal isactivated, the REC LED on therecorder and the camera will flashfor about 1 second.

•The video signal from the inputselected with the Toughbook-Arbitrator Front End Software willbe recorded (see page 18).

Recording can be stopped by one ofthe following methods:•Pressing the STOP button on therecorder.

•Clicking the STOP button in the Toughbook-Arbitrator Front End Software.

When recording is stopped, the post-recording function operates to ensurethat material from a certain intervalafter the stop point is included in therecording. The duration of this intervalcan be set with the Toughbook-Arbitrator Front End Software.

Notes:•The entire video and audio contentof the recording period, includingthe prerecording and post-recording intervals, is stored asone file on the P2 card.

•When recording on a 4 GB P2 cardat 512 kbps recording rate, therecording time may be 17 hours ormore, if there is no great change inthe recorded image. In such acase, the recorded fi le wil l beautomatically split.

•When recording is started by arecording start trigger signal, therecorded video signal will always bethe signal originating from thecamera unit, via the camera inputcable. If a recording start triggersignal is activated while recording avideo signal from the VIDEO INconnector, recording wil lautomatically switch to the videosignal originating from the cameraunit, via the camera input cable.

•The audio signal from the inputselected with the Toughbook-Arbitrator Front End Software willbe recorded (see page 18).

• If the cover is opened duringrecording, recording will stop.

• If the cover is not closed, recordingcannot be restarted.

Stopping

17

Recording and stopping (continued)

Write-protect switchThe P2 card is equipped with a write-protect switch. If you set this switch tothe PROTECT position, no data canbe written to the P2 card and noexisting file can be deleted.

PROTECT

write-protect switch

Prerecording and post-recording

Prerecording is the capability of includingmaterial from an interval before thespecif ied start point in a recording.Similarly, post-recording is the capability ofincluding material from an interval after thespecified stop point in a recording. Theintervals (prerecord time and post-recordtime) can be set using the Toughbook-Arbitrator Front End Software.

If recording is startedimmediately after system startupPrerecord time will be shorter.

If recording is started duringpost-record intervalPost-recording will be terminatedand next recording starts. There isno prerecording interval for thesecond recording.

REC button pressed(Recording starts)

STOP button pressed(Recording stops)

Actual recording time

Prerecord time Post-record time

Prerecord time Post-record time

REC button pressed(Post-recording halted andnext recording starts)


STOPbuttonpressed


REC button pressed(Recording starts)


Startupcompleted

Post-record time Post-record time

In the cases shown below, the actualprerecord and post-record time may beshorter than the respective setting.

Notes:• If you press the REC button andSTOP button alternately in rapidsuccession, the system may notseparate the two recording sessions,resulting in a single video file.

• If the remaining capacity of the P2card is low, the prerecord time or post-record time may become shorter.

Notes:•Any attempt to change the positionof the write-protect switch duringpower-on will have no effect. Toproduce the effect, turn the poweroff and then turn it on again orremove the card and then insert itagain.

• If the write-protect switch is set tothe PROTECT position on any ofthe cards in the two card slots,recording will not start.


Time

Time

Time

18

Recording and stopping (continued)

Selecting the video source to record

You can select to record from eitherthe camera cable input signal or theVIDEO IN connector input signal onthe rear panel. This selection is madeusing the Toughbook-Arbitrator FrontEnd Software.If a recording start trigger signal isactivated while recording a signal fromthe VIDEO IN connector, recording ofthe VIDEO IN signal will stop andrecording of the camera cable inputsignal will begin. In this case, separatefiles will be created. When recording isstarted by trigger activation, there willbe no prerecording or post-recording.

Recording start trigger activation

Recording of signalfrom VIDEO INconnector

Recording of signal fromcamera cable connector

Notes:• If switching was performed bysupplying a recording start trigger,the input signal immediately afterswitching will not be recorded.

• If the video signal selection ischanged during post-recording, post-recording will be halted.

• If recording is started immediatelyafter selecting the video signal, theprerecord time may be shorterthan the setting.

•When the recorder is restarted, thedefault video signal input setting isalways the camera cableconnector, regardless of whichselection was active beforeshutdown.

Note:When the recorder is restarted, thedefault audio signal sett ing isalways the MIC, regardless of whichselection was active beforeshutdown.

Time

The recorder can record up to twoaudio channels (L-CH and R-CH). Outof the three audio input connectors onthe rear panel (AUDIO IN 1, 2, andMIC IN), the signal of the sourceconnected to the AUDIO IN 1connector will always be recorded onthe left channel (L-CH). For the rightchannel (R-CH), you can select eitherthe signal from the AUDIO IN 2connector or the MIC IN connector.This selection is made using theToughbook-Arbitrator Front EndSoftware.The following two audio recordingmodes are available: AUDIO IN 2 andMIC

AUDIO IN2During recording, the audio signalfrom the AUDIO IN 2 connector willalways be recorded on the rightchannel (R-CH).

MICDuring recording, the audio signalfrom the MIC IN connector wil lalways be recorded on the rightchannel (R-CH).

Audio sources when recording

19

Zoom functionThe camera has the capability foroptical zoom (x22) and digital zoom(x10). The zoom function is controlledwith the W button and the T button.The maximum zoom factor is x220.When zooming in on a subject fromthe wide end, zooming automaticallypauses at the x22 limit of the opticalzoom. To zoom beyond this limit withthe digital zoom, release the zoombutton momentarily and press itagain, holding it down until thedesired zoom factor is reached. Thesame process is used to zoom outfrom the telephoto end.

Auto zoom functionWhen you press the auto zoombutton, the camera wil lautomatically zoom in, pause for acertain period, and zoom out. Thezoom factor and pause duration canbe set with the Toughbook-Arbitrator Front End Software.

Camera operationBacklight compensation functionWhen you press the backlightcompensation button, the backlightcompensation function is activated.Each push of the button toggles thefunction between ON and OFF.

Light buttonPressing this button activates thecamera operation panel illumination.Each push of the button toggles theillumination between ON and OFF.

20

LEDs and recorder statusThe relationship between the on/flashing status of the indicator LEDs on the recorderand camera and the operation status of the recorder is shown in the table below.

: LED lit : LED flashing : LED out

1 “REC LED” refers to the following indicators and pins:•REC LED on recorder•REC LED on camera•GPIO9 (pin 25) output of GPIO/SERIAL port (Rec Tally)The REC LED on the camera and the GPIO9 output connector will not flashimmediately after power-on.

2 Shows the following P2 card status information:•No P2 card is inserted.•P2 card does not have sufficient free space.•Write-protect switch is set to the PROTECT position on at least one card.

3 Carried out by the recorder in response to a request by the ToughbookArbitrator Front End Software.

4 If the P2 card does not have sufficient free space, the READY LED does not light.5 Recorder administrator settings can be changed from the Toughbook-ArbitratorFront End Software.

• If recording is already in progress or if recording cannot be started when theREC button is pressed or a recording start trigger is activated via theGPIO/SERIAL port, the REC LED flashes for about 1 second.

•During card access immediately after the cover was opened or closed, theBUSY LED flashes.

LED statusREC 1 READY BUSY

Immediately after power-on

During startup

Standby (recording possible)

Standby (recording impossible) 2

Recording in progress

Recording in progress (remaining capacity less than. 30 minutes)

Post-recording in progress

File restoration in progress 3

Playback (upload) in progress 4

Setting change in progress 5

Cover is open

Shutdown in progress

Recorder status

21

Notes on handlingInstallation• Install the recorder and camera

properly as described in theinstallation manual, so that theunits cannot come loose or fall off.

• Do not place heavy objects on thepower cable and other connectioncables.

• Do not exceed the rating of anyconnection cables and other wiringparts.

• Use only the supplied accessoriesand specified optional accessories.

• Keep the recorder, camera, P2card, power cable and connectioncables away from heat sources.

• Protect the recorder, camera andP2 cards from oily smoke,humidity, moisture, and dust.

• Do not touch the power supplyconnector with wet hands.

• Do not block the ventilation holesof the recorder.

Usage• The recorder is designed to be

powered from a 12-volt source. Itcannot be used in vehicles with adifferent electrical source voltage.(Never connect the recorder to a24-volt source.)

• When using the recorder for thefirst time or after reconnecting it tothe power supply, be sure to setthe date, time, and time zone ofthe internal clock using theToughbook-Arbitrator Front EndSoftware.

• Do not place any container withliquid or any small metal objectson top of the recorder, camera, orP2 card.

• Do not insert any foreign objectsinto the openings of the unit.

• Do not attempt to modify therecorder, camera, or P2 card.

• Take care not to damage thepower cable or connection cables.Do not modify, bend, twist, curl, orpull these parts or subject them toa strong stress force. Also avoidexposure to high temperatures.

• Protect the recorder, camera, andP2 cards from moisture and do notexpose them to water.

• Do not place heavy objects on therecorder or camera and do notstep on these parts. Do notsuspend any heavy objects fromthe mounted camera.

• Before moving the recorder orcamera, be sure to disconnect thepower cable and other connectioncables.

• Do not handle the recorder orcamera while driving a vehicle.

• Only P2 type memory cards canbe used in the recorder. Do notuse any other type of card,because this wil l damage therecorder.

• When inserting a P2 card, proceedcarefully and do not use excessiveforce. Otherwise the P2 card orthe card slot will be damaged.

• Do not insert the P2 card upsidedown.

• Do not insert a damaged ordeformed P2 card.

22

• Do not disconnect the power cablewhile the recorder is operating. Besure to perform recorder shutdownbefore disconnecting the cable.Otherwise recorder setting filesand P2 card managing informationmay be lost or damaged.When the SIGNAL pin at the DCIN connector goes OFF, therecorder will perform shutdownafter an interval set with theToughbook-Arbitrator Front EndSoftware.

• Do not open the cover during P2card access (BUSY LED is lit orflashing). Do not exert undue forceon the cover to prevent damage.

• Never remove the P2 card fromthe card slot during P2 cardaccess (BUSY LED is l i t orflashing). Otherwise data on theP2 card will be destroyed.

• Take care not to pinch your fingersin the P2 card slots or the cover.

• Protect the connector section ofthe P2 card from dust, sand,moisture etc. If a card has beenexposed to any of these, do notinsert it in the P2 card slot.

• Take care that no dust, sand,moisture etc. can enter a P2 cardslot.

• Before closing the cover, makesure that the EJECT button isfolded to the right.

• Do not exert undue force on theEJECT button to prevent damage.

What to do in case of a problem• If the recorder or camera was

dropped, or if a foreign substancehas entered a unit, stop recording,shut down the unit and disconnectthe power cable.

• If a component emits smoke,unusual smell or noise, or ifanother problem occurs,disconnect the power cable.

Maintenance• Before performing any

maintenance operation, make surethat the recorder is not operatingand then disconnect the powercable.

• Regularly check the ventilationholes for blockage by dust etc.

Notes on handling (continued)

23

Factory default settingsThe factory default settings are listed in the table below. To change any of thesesettings, use the Toughbook-Arbitrator Front End Software, but “17 IP Address”will not be changed.

Item Value Description(Recorder related settings)

ShiftShift Start 2005-01-01 Shift start date, time and day 1

09:00SAT

Shift End 2005-01-01 Shift end date, time and day 1

17:00SAT

Shift Pattern ---- Shift patternOfficerOfficer1 first name ---- Officer 1 first nameOfficer1 mid name - Officer 1 middle nameOfficer1 last name ---- Officer 1 last nameOfficer1 ID -------- Officer 1 IDOfficer2 first name ---- Officer 2 first nameOfficer2 mid name - Officer 2 middle nameOfficer2 last name ---- Officer 2 last nameOfficer2 ID -------- Officer 2 ID

3 Vehicle ID -------- Patrol car ID4 Area ---- Area number5 Record Rate 512 K Recording bit rate

Setting values 1M: 1 Mbps512 K: 512 Kbps

6 Time and Date (undefined) Year Month/Day Hour/Minutes Seconds7 Time Zone Pacific Daylight Time zone

Saving Time Setting values:Hawaii Standard TimeYukon Standard (Daylight Saving) TimePacific Standard (Daylight Saving) TimeMountain Standard (Daylight Saving) TimeCentral Standard (Daylight Saving) TimeEastern Standard (Daylight Saving) TimeAtlantic Standard (Daylight Saving) TimeAsia Tokyo

1

2

1 Displayed values differ depending on the Time Zone setting.

24

Factory default settings (continued)

8 V-CH 1 Video inputSetting values1: Camera cable connector input

2: VIDEO IN connector input9 AUDIO2 MIC Audio input

Setting values: AUDIO IN2MIC

(For information on audio settings, see page 18.)10 Pre Time 120 Prerecord time (seconds)

Setting values: 0 - 18011 Post Time 120 Post-record time (seconds)

Setting values: 0 - 18012 Power On/Off 120 Time lag between SIGNAL off and

recorder shutdown (minutes)Setting values: 0 - 180 1

13 P-Rec OFF Automatically start recording at SIGNAL ONSetting values: ON

OFFGPIO Settings for GPIO ports 1 - 8 (common to all ports)GPIO On/Off ON Enable/disable global GPIO

Setting values:ON (Globally enable GPIO input)OFF (Globally disable GPIO input)

DETECTION H Individual trigger settings for GPIO 1 - 8Setting values: N (No input)

H (High-edge trigger)L (Low-edge trigger)B (Both-edge trigger)

Name ---- GPIO 1 - 8 namesSetup ON Individual OSD display settings for GPIO 1 - 8

Setting values: ON (OSD on)OFF (OSD off)

Printable - OSD character string for GPIO 1 - 815 AUDIO2 REC ON Audio R-CH recording

Setting values: ONOFF

14

1 When set to “0”, the recorder will perform shutdown after about one minute.

25


OSDOSD On/Off OSD On OSD enable/disable

GPIO On Setting values: OSD OFFTimeDate On OSD ON, GPIO ON, TimeDate ON

OSD ON, GPIO ON, TimeDate OFFOSD ON, GPIO OFF, TimeDate ON

TIME-DATE ISO Time/Date display formatSTYLE Setting values: ISO (ISO format)

USA (USA format)--- 1lineUpper Display position

Setting values:1lineUpperEnd: 1-line display, upper end1lineUpper: 1-line display, top1lineBottom: 1-line display, bottom1lineBottomEnd: 1-line display, bottom end2linesL-upper: 2-line display, upper left2linesR-upper: 2-line display, upper right2linesL-bottom: 2-line display, bottom left2linesR-bottom: 2-line display, bottom right3linesL-upper: 3-line display, upper left3linesR-upper: 3-line display, upper right3linesL-bottom: 3-line display, bottom left3linesR-bottom: 3-line display, bottom right

16

26


R-ProtocolBaud Rate 4800 Radar gun communication rate (bps)

Setting value: 50 - 230400Bit Length 8 Communication word length (bits)

Setting values: 87

Stop Bit 1 Stop bits (bit)Setting value: 1,2

Parity NON ParitySetting values: ODD

NONEVEN

Delimit OFF DelimiterCharacter Setting value: OFF

\ D\ A

Buffer Size 255 Transfer buffer size (bytes)Setting value: 0 - 256

Data timeout 1 Transfer timeout (100 msec.)Setting value: 1 - 999

IP Address 192.168.10.10/24 IP Address of the recorder(This will not be changed.)

17

18

27


(Camera related settings)1 ZOOM-LIM 22 Maximum zoom factor

Target Magnification Setting values: 22 - 220(The values except 22 are multiples of 20.)

1 - 220(Values from 1 to 22 are integers, and valuesof 40 and above are multiples of 20.)

2 AUTO ZOOM 10 Target zoom factor when AutoZoom command is receivedTarget Magnification Setting values: 1 - 22 (integers)

3 AUTO ZOOM 3 Interval of maintaining target zoom Maintenance Time factor when AutoZoom command is received

Setting values: 0 - 9 (integers)4 Back Light OFF Backlight compensation enable/disable

Setting values: ON (Backlight compensation enabled)OFF (Backlight compensation disabled)

5 Camera LED ON Camera REC LED enable/disableSetting values:

ON (Camera REC LED lights up during recording)OFF (Camera REC LED is always off)

6 Flip OFF Camera output image top/bottom flip enable/disableSetting values:

ON (Top/bottom flip enabled)OFF (Top/bottom flip disabled)

28


7 Infra Red AUTO IR function auto switch/always ON/always OFF 2

Setting values:AUTO (IR function is automatically switched on and off)ON (IR function is always on)OFF (IR function is always off)

8 IR-Level LOW Level setting for IR auto switching mode 2

Setting values: LOWHIGH

9 IR-Time 30 Detection time setting for IR auto switching mode (seconds) 2

Setting values: 10: 10 seconds30: 30 seconds60: 60 seconds300: 300 seconds

10 AGC HIGH Camera input gain settingSetting values: LOW

MIDHIGHOFF

11 AE Shift 0 Auto exposure shift 3

Setting values: –2, –1, 0, 1, 2

2 The IR-Level and IR-Time settings are only available when IR is set to AUTO.3 When the “AE Shift” value is “2” and the object is fairly dark, the image may notbe updated at the 30 frames per second rate.The default AE shift value is always 0, when the recorder is restarted.

29

Connector signals

1 N.C.

2 V_OUT

3 BL_L

4 AUTO_ZOOM_L

5 REC_L

6 GND (DC_IN)

7 DC_IN

8 N.C.

9 GND (SHIELD)

10 GND (V_OUT)

11 GND (TxD/RxD)

12 TxD

13 RxD

14 REC_LED_L

15 GND (SHIELD)

16 GND (SHIELD)

Camera cable connector(recorder/female)

1 GND Black

2 BATT Red

3 SIGNAL White

4 N.C.

DC IN connector(recorder/female)

Pin number Signal

Pin number Signal Cable color

1

9 16

8

1 4

Power cable (supplied)

RedBlack

White

The SIGNAL pin can be used to turn power to the recorder on and off. When anOFF signal is input at this pin while the recorder is powered, the recorder willturn off after an interval set with the Toughbook-Arbitrator Front End Software.

30

Connector signals (continued)

1 N.C.

2 TxD Serial

3 RxD Serial

4 RTS Serial

5 CTS Serial

6 DSR Serial

7 SG Serial

8 CD Serial

9 GND GPIO Black

10 GPIO1 In Brown

11 GPIO2 In Red

12 GPIO3 In Orange

13 GPIO4 In Yellow

14 N.C.

15 N.C.

16 N.C.

17 N.C.

18 N.C.

19 N.C.

20 DTR Serial

21 GPIO5 In Green

22 GPIO6 In Blue

23 GPIO7 In Purple

24 GPIO8 In Gray

25 GPIO9 Out White

GPIO/Serial connector(recorder/female)

Pin number Signal Remarks Cable

color

13

25 14

1

External trigger cable (supplied)

BrownRedOrangeYellowGreenBluePurpleGrayWhite

Black

RS-232C

31

Connector signals (continued)

Camera cable connector(camera/female)

1 GND (SHIELD)

2 REC_LED_L

3 RxD

4 TxD

5 GND (TxD/RxD)

6 GND (V_OUT)

7 DC_IN

8 GND (DC_IN)

9 REC_L

10 AUTO_ZOOM_L

11 BL_L

12 V_OUT

Pin number Signal

912

5

10

111

32

TroubleshootingBefore requesting service, check the points listed below. If the problem persists,contact your local Panasonic dealer.

Starting up• Check whether power cable is connected

correctly.• Check whether a timer device is inserted in the

power supply for the recorder. Refer to theinstallation manual and connect the timerequipment correctly.

• Check the time lag setting between SIGNAL offand recorder power-off. For details, see thedocumentation of the Toughbook-ArbitratorFront End Software.

Operation• Are you using the supplied key?• Is the cover closed? The key can only be

removed if the cover is closed.• Is a P2 card inserted correctly in a P2 card slot?• Is the EJECT button folded to the right?• Is the supplied LAN cable (crossing type) being

used? Connect the recorder and the computeron which the Toughbook-Arbitrator Front EndSoftware is running directly, not via a hub.

• Are the network settings on the computercorrect? Subnet mask of the recorder and thatof the computer must be the same. For details,see the documentation of the Toughbook-Arbitrator Front End Software.

• When you press and hold the REC button andSTOP button on the recorder simultaneously forabout 10 seconds, the recorder will restart.Reset the computer after this.

• To reset the unit, hold down the REC button and STOPbutton on the front panel together for about 10 seconds.All LEDs go out for 1 - 2 seconds and then lightup for 1 - 2 seconds. Reset is now possible.

• If you remove the P2 card during P2 cardaccess (BUSY LED is lit), the P2 card slot maybecome inoperative. In such a case, therecorder automatically restarts itself, and thecard slot will become operative again.

Recorder

Cover cannot be opened.

Power does not come on.

Power gets turned offautomatically.

Key cannot be removedfrom lock.

Control from Toughbook-Arbitrator Front EndSoftware is not possible.

The unit does not respondor another problem hasoccurred.

Recorder was restartedwithout performing areset.

Cover cannot be closed.

33

Recorded data havebecome totally or partiallyunusable.

Troubleshooting (continued)

Recording(Check this with the Toughbook-Arbitrator FrontEnd Software.)• Is a P2 card inserted?• Does the P2 card have sufficient free space?

Check the free space with the Toughbook-Arbitrator Front End Software. Upload files andfree up space.

• Make sure that the write-protect switch of the P2card is not set to PROTECT.

• Is the GPIO cable connected properly? Alsoconnect the ground line of the GPIO cable. Fordetails, see the installation manual.

• Are the settings for the GPIO/SERIAL portcorrect? For details, see the documentation ofthe Toughbook-Arbitrator Front End Software.

• Is the P2 card usable? If file information cannotbe obtained using the Toughbook-ArbitratorFront End Software, you should format the P2card. For information on formatting, see theinstallation manual. (When you format a P2card, all existing data on it will be erased.)

• If the power source was interrupted or if thepower cable was disconnected during recording,data may become corrupted. Ensure that poweris never interrupted during recording. In somecases, it may be possible to restore corrupteddata using the Toughbook-Arbitrator Front EndSoftware.

Cannot start recording.

34


(Check this with the Toughbook-Arbitrator FrontEnd Software.)• Are camera and video monitoring equipment

connected properly?• Are both the video input connector selection and

the input selection made with the Toughbook-Arbitrator Front End Software the same?

• Are the video output settings correct for theconnected equipment? Connect a monitor to theVIDEO OUT connector on the rear panel of therecorder and check the picture.

(Check this with the Toughbook-Arbitrator FrontEnd Software.)• Is the cable connection to the audio input

correct?• Are both the audio input connector selection

and the input selection made with theToughbook-Arbitrator Front End Software thesame?

• Are the audio output settings correct for theconnected equipment? Consult thedocumentation of the connected equipment tocheck this.

• Check the audio settings at the computer.(Check this with the Toughbook-Arbitrator FrontEnd Software.)• Are the communication settings of the

connected equipment and the settings for theSERIAL port of the recorder the same? Checkthis while referring to the documentation forconnected equipment and the Toughbook-Arbitrator Front End Software.

Video is distorted or notrecorded.

Sound is distorted or notrecorded.

Information fromequipment connected viathe GPIO/SERIAL port isnot recorded in the metadata file

35

Video is distorted or notrecorded.


Power does not come on.Starting up and during operating

• Is the camera cable connected correctly? Checkthis while referring to the installation manual.

• Immediately after power-on or when switchingto IR mode, a mechanical operation sound willbe heard. This is not a malfunction of thecamera.

• During zoom, some operation noise will beheard. This is not a defect.

Picture(Check this with the Toughbook-Arbitrator FrontEnd Software.)• Are camera and video monitoring equipment

connected properly?• Are both the video input connector selection and

the input selection made with the Toughbook-Arbitrator Front End Software the same?

• Are the video output settings correct for theconnected equipment? Connect a monitor to theVIDEO OUT connector on the rear panel of therecorder and check the picture.

• The IR function was enabled, which results in aB/W picture.

• Under some circumstances, correct focus maybe difficult to achieve with auto-focusing. A fewexamples are listed below:· The field of view includes both distant andnear objects.

· The camera is shooting through dirty windowglass.

· Ambient lighting is low.· There are bright and reflective surfacesaround the object.

· The camera is shooting a rapidly movingobject.

· The object has little contrast.· A close-by object is being shot at high zoomratio.

Camera

Recorded video is inblack and white.Automatic focusing doesnot work.

Unusual sound is heard.

36

GPLGNU GENERAL PUBLIC LICENSEVersion 2, June 1991

Copyright (C) 1989, 1991 Free Software Foundation, Inc.59 Temple Place, Suite 330, Boston, MA 02111-1307 USAEveryone is permitted to copy and distribute verbatimcopies of this license document, but changing it is notallowed.

Preamble

The licenses for most software are designed to take awayyour freedom to share and change it. By contrast, theGNU General Public License is intended to guaranteeyour freedom to share and change free software--to makesure the software is free for all its users. This GeneralPublic License applies to most of the Free SoftwareFoundation’s software and to any other program whoseauthors commit to using it. (Some other Free SoftwareFoundation software is covered by the GNU LibraryGeneral Public License instead.) You can apply it to yourprograms, too.

When we speak of free software, we are referring tofreedom, not price. Our General Public Licenses aredesigned to make sure that you have the freedom todistribute copies of free software (and charge for thisservice if you wish), that you receive source code or canget it if you want it, that you can change the software oruse pieces of it in new free programs; and that you knowyou can do these things.

To protect your rights, we need to make restrictions thatforbid anyone to deny you these rights or to ask you tosurrender the rights. These restrictions translate to certainresponsibilities for you if you distribute copies of thesoftware, or if you modify it.

For example, if you distribute copies of such a program,whether gratis or for a fee, you must give the recipients allthe rights that you have. You must make sure that they,too, receive or can get the source code. And you mustshow them these terms so they know their rights.

We protect your rights with two steps: (1) copyright thesoftware, and (2) offer you this license which gives youlegal permission to copy, distribute and/or modify thesoftware.

Also, for each author's protection and ours, we want tomake certain that everyone understands that there is nowarranty for this free software. If the software is modifiedby someone else and passed on, we want its recipients toknow that what they have is not the original, so that anyproblems introduced by others will not reflect on theoriginal authors’ reputations.

Finally, any free program is threatened constantly bysoftware patents. We wish to avoid the danger thatredistributors of a free program will individually obtainpatent licenses, in effect making the program proprietary.To prevent this, we have made it clear that any patentmust be licensed for everyone’s free use or not licensed atall.

The precise terms and conditions for copying, distributionand modification follow.

GNU GENERAL PUBLIC LICENSE

TERMS AND CONDITIONS FOR COPYING,DISTRIBUTION AND MODIFICATION

0. This License applies to any program or other workwhich contains a notice placed by the copyright holdersaying it may be distributed under the terms of thisGeneral Public License. The “Program”, below, refers toany such program or work, and a “work based on theProgram” means either the Program or any derivativework under copyright law: that is to say, a workcontaining the Program or a portion of it, either verbatimor with modifications and/or translated into anotherlanguage. (Hereinafter, translation is included withoutlimitation in the term “modification”.) Each licensee isaddressed as “you”.

Activit ies other than copying, distribution andmodification are not covered by this License; they areoutside its scope. The act of running the Program is notrestricted, and the output from the Program is coveredonly if its contents constitute a work based on theProgram (independent of having been made by runningthe Program). Whether that is true depends on what theProgram does.

1. You may copy and distribute verbatim copies of theProgram ’s source code as you receive it, in anymedium, provided that you conspicuously andappropriately publish on each copy an appropriatecopyright notice and disclaimer of warranty; keep intactall the notices that refer to this License and to theabsence of any warranty; and give any other recipientsof the Program a copy of this License along with theProgram.

You may charge a fee for the physical act of transferringa copy, and you may at your option offer warrantyprotection in exchange for a fee.

2. You may modify your copy or copies of the Program orany portion of it, thus forming a work based on theProgram, and copy and distribute such modifications orwork under the terms of Section 1 above, provided thatyou also meet all of these conditions:

a) You must cause the modified files to carry prominentnotices stating that you changed the files and thedate of any change.

b) You must cause any work that you distribute orpublish, that in whole or in part contains or is derivedfrom the Program or any part thereof, to be licensedas a whole at no charge to all third parties under theterms of this License.

c) If the modified program normally reads commandsinteractively when run, you must cause it, whenstarted running for such interactive use in the mostordinary way, to print or display an announcementincluding an appropriate copyright notice and anotice that there is no warranty (or else, saying thatyou provide a warranty) and that users mayredistribute the program under these conditions, andtelling the user how to view a copy of this License.(Exception: if the Program itself is interactive butdoes not normally print such an announcement, yourwork based on the Program is not required to print anannouncement.)

37

GPL (continued)

These requirements apply to the modified work as awhole. If identifiable sections of that work are not derivedfrom the Program, and can be reasonably consideredindependent and separate works in themselves, then thisLicense, and its terms, do not apply to those sectionswhen you distribute them as separate works. But whenyou distribute the same sections as part of a whole whichis a work based on the Program, the distribution of thewhole must be on the terms of this License, whosepermissions for other licensees extend to the entire whole,and thus to each and every part regardless of who wroteit.

Thus, it is not the intent of this section to claim rights orcontest your rights to work written entirely by you; rather,the intent is to exercise the right to control the distributionof derivative or collective works based on the Program.

In addition, mere aggregation of another work not basedon the Program with the Program (or with a work based onthe Program) on a volume of a storage or distributionmedium does not bring the other work under the scope ofthis License.

3. You may copy and distribute the Program (or a workbased on it,under Section 2) in object code orexecutable form under the terms of Sections 1 and 2above provided that you also do one of the following:

a) Accompany it with the complete correspondingmachine-readable source code, which must bedistributed under the terms of Sections 1 and 2above on a medium customarily used for softwareinterchange; or,

b) Accompany it with a written offer, valid for at leastthree years, to give any third party, for a charge nomore than your cost of physically performing sourcedistribution, a complete machine-readable copy ofthe corresponding source code, to be distributedunder the terms of Sections 1 and 2 above on amedium customarily used for software interchange;or,

c) Accompany it with the information you received as tothe offer to distribute corresponding source code.(This alternative is allowed only for noncommercialdistribution and only if you received the program inobject code or executable form with such an offer, inaccord with Subsection b above.)

The source code for a work means the preferred form ofthe work for making modifications to it. For an executablework, complete source code means all the source code forall modules it contains, plus any associated interfacedefinition files, plus the scripts used to control compilationand installation of the executable. However, as a specialexception, the source code distributed need not includeanything that is normally distributed (in either source orbinary form) with the major components (compiler, kernel,and so on) of the operating system on which theexecutable runs, unless that component itselfaccompanies the executable.

If distribution of executable or object code is made byoffering access to copy from a designated place, thenoffering equivalent access to copy the source code fromthe same place counts as distribution of the source code,

even though third parties are not compelled to copy thesource along with the object code.

4. You may not copy, modify, sublicense, or distribute theProgram except as expressly provided under thisLicense. Any attempt otherwise to copy, modify,sublicense or distribute the Program is void, and willautomatically terminate your rights under this License.However, parties who have received copies, or rights,from you under this License will not have their licensesterminated so long as such parties remain in fullcompliance.

5. You are not required to accept this License, since youhave not signed it. However, nothing else grants youpermission to modify or distribute the Program or itsderivative works. These actions are prohibited by law ifyou do not accept this License. Therefore, by modifyingor distributing the Program (or any work based on theProgram), you indicate your acceptance of this Licenseto do so, and all its terms and conditions for copying,distributing or modifying the Program or works based onit.

6. Each time you redistribute the Program (or any workbased on the Program), the recipient automaticallyreceives a license from the original licensor to copy,distribute or modify the Program subject to these termsand conditions. You may not impose any furtherrestrictions on the recipients’ exercise of the rightsgranted herein. You are not responsible for enforcingcompliance by third parties to this License.

7. If, as a consequence of a court judgment or allegationof patent infringement or for any other reason (notlimited to patent issues), conditions are imposed on you(whether by court order, agreement or otherwise) thatcontradict the conditions of this License, they do notexcuse you from the conditions of this License. If youcannot distribute so as to satisfy simultaneously yourobligations under this License and any other pertinentobligations, then as a consequence you may notdistribute the Program at all. For example, if a patentlicense would not permit royalty-free redistribution of theProgram by all those who receive copies directly orindirectly through you, then the only way you couldsatisfy both it and this License would be to refrainentirely from distribution of the Program.

If any portion of this section is held invalid orunenforceable under any particular circumstance, thebalance of the section is intended to apply and the sectionas a whole is intended to apply in other circumstances.

It is not the purpose of this section to induce you toinfringe any patents or other property right claims or tocontest validity of any such claims; this section has thesole purpose of protecting the integrity of the free softwaredistribution system, which is implemented by publiclicense practices. Many people have made generouscontributions to the wide range of software distributedthrough that system in reliance on consistent application ofthat system; it is up to the author/donor to decide if he orshe is willing to distribute software through any othersystem and a licensee cannot impose that choice.

This section is intended to make thoroughly clear what is

38

GPL (continued)

believed to be a consequence of the rest of this License.

8. If the distribution and/or use of the Program is restrictedin certain countries either by patents or by copyrightedinterfaces, the original copyright holder who places theProgram under this License may add an explicitgeographical distribution limitation excluding thosecountries, so that distribution is permitted only in oramong countries not thus excluded. In such case, thisLicense incorporates the limitation as if written in thebody of this License.

9. The Free Software Foundation may publish revisedand/or new versions of the General Public License fromtime to time. Such new versions will be similar in spiritto the present version, but may differ in detail toaddress new problems or concerns.

Each version is given a distinguishing version number. Ifthe Program specifies a version number of this Licensewhich applies to it and “any later version”, you have theoption of following the terms and conditions either of thatversion or of any later version published by the FreeSoftware Foundation. If the Program does not specify aversion number of this License, you may choose anyversion ever published by the Free Software Foundation.

10. If you wish to incorporate parts of the Program intoother free programs whose distribution conditions aredifferent, write to the author to ask for permission. Forsoftware which is copyrighted by the Free SoftwareFoundation, write to the Free Software Foundation; wesometimes make exceptions for this. Our decision willbe guided by the two goals of preserving the free statusof all derivatives of our free software and of promotingthe sharing and reuse of software generally.

NO WARRANTY

11. BECAUSE THE PROGRAM IS LICENSED FREE OFCHARGE, THERE IS NO WARRANTY FOR THEPROGRAM, TO THE EXTENT PERMITTED BYAPPLICABLE LAW. EXCEPT WHEN OTHERWISESTATED IN WRITING THE COPYRIGHT HOLDERSAND/OR OTHER PARTIES PROVIDE THEPROGRAM “AS IS” WITHOUT WARRANTY OF ANYKIND, EITHER EXPRESSED OR IMPLIED,INCLUDING, BUT NOT LIMITED TO, THE IMPLIEDWARRANTIES OF MERCHANTABILITY ANDFITNESS FOR A PARTICULAR PURPOSE. THEENTIRE RISK AS TO THE QUALITY ANDPERFORMANCE OF THE PROGRAM IS WITH YOU.SHOULD THE PROGRAM PROVE DEFECTIVE, YOUASSUME THE COST OF ALL NECESSARYSERVICING, REPAIR OR CORRECTION.

12. IN NO EVENT UNLESS REQUIRED BY APPLICABLELAW OR AGREED TO IN WRITING WILL ANYCOPYRIGHT HOLDER, OR ANY OTHER PARTYWHO MAY MODIFY AND/OR REDISTRIBUTE THEPROGRAM AS PERMITTED ABOVE, BE LIABLE TOYOU FOR DAMAGES, INCLUDING ANY GENERAL,SPECIAL, INCIDENTAL OR CONSEQUENTIALDAMAGES ARISING OUT OF THE USE ORINABILITY TO USE THE PROGRAM (INCLUDINGBUT NOT LIMITED TO LOSS OF DATA OR DATABEING RENDERED INACCURATE OR LOSSES

SUSTAINED BY YOU OR THIRD PARTIES OR AFAILURE OF THE PROGRAM TO OPERATE WITHANY OTHER PROGRAMS), EVEN IF SUCH HOLDEROR OTHER PARTY HAS BEEN ADVISED OF THEPOSSIBILITY OF SUCH DAMAGES.

END OF TERMS AND CONDITIONS

39

LGPLGNU LESSER GENERAL PUBLIC LICENSEVersion 2.1, February 1999Copyright (C) 1991, 1999 Free Software Foundation, Inc.59 Temple Place, Suite 330, Boston, MA 02111-1307USA Everyone is permitted to copy and distribute verbatimcopies of this license document, but changing it is notallowed.

[This is the first released version of the Lesser GPL. It alsocounts as the successor of the GNU Library PublicLicense, version 2, hence the version number 2.1.]

PreambleThe licenses for most software are designed to take awayyour freedom to share and change it. By contrast, theGNU General Public Licenses are intended to guaranteeyour freedom to share and change free software--to makesure the software is free for all its users.

This license, the Lesser General Public License, applies tosome specially designated software packages--typicallylibraries--of the Free Software Foundation and otherauthors who decide to use it. You can use it too, but wesuggest you first think carefully about whether this licenseor the ordinary General Public License is the betterstrategy to use in any particular case, based on theexplanations below.

When we speak of free software, we are referring tofreedom of use, not price. Our General Public Licensesare designed to make sure that you have the freedom todistribute copies of free software (and charge for thisservice if you wish); that you receive source code or canget it if you want it; that you can change the software anduse pieces of it in new free programs; and that you areinformed that you can do these things.

To protect your rights, we need to make restrictions thatforbid distributors to deny you these rights or to ask you tosurrender these rights. These restrictions translate tocertain responsibilities for you if you distribute copies ofthe library or if you modify it.

For example, if you distribute copies of the library, whethergratis or for a fee, you must give the recipients all therights that we gave you. You must make sure that they,too, receive or can get the source code. If you link othercode with the library, you must provide complete objectfiles to the recipients, so that they can relink them with thelibrary after making changes to the library and recompilingit. And you must show them these terms so they knowtheir rights.

We protect your rights with a two-step method: (1) wecopyright the library, and (2) we offer you this license,which gives you legal permission to copy, distribute and/ormodify the library.

To protect each distributor, we want to make it very clearthat there is no warranty for the free library. Also, if thelibrary is modified by someone else and passed on, therecipients should know that what they have is not theoriginal version, so that the original author’s reputation willnot be affected by problems that might be introduced byothers.

Finally, software patents pose a constant threat to theexistence of any free program. We wish to make sure thata company cannot effectively restrict the users of a freeprogram by obtaining a restrictive license from a patent

holder. Therefore, we insist that any patent licenseobtained for a version of the library must be consistentwith the full freedom of use specified in this license.

Most GNU software, including some libraries, is coveredby the ordinary GNU General Public License. This license,the GNU Lesser General Public License, applies to certaindesignated libraries, and is quite different from theordinary General Public License. We use this license forcertain libraries in order to permit linking those librariesinto non-free programs.

When a program is linked with a library, whether staticallyor using a shared library, the combination of the two islegally speaking a combined work, a derivative of theoriginal library. The ordinary General Public Licensetherefore permits such l inking only if the entirecombination fits its criteria of freedom. The Lesser GeneralPublic License permits more lax criteria for linking othercode with the library.

We call this license the “Lesser” General Public Licensebecause it does Less to protect the user’s freedom thanthe ordinary General Public License. It also provides otherfree software developers Less of an advantage overcompeting non-free programs. These disadvantages arethe reason we use the ordinary General Public License formany libraries. However, the Lesser license providesadvantages in certain special circumstances.

For example, on rare occasions, there may be a specialneed to encourage the widest possible use of a certainlibrary, so that it becomes a de-facto standard. To achievethis, non-free programs must be allowed to use the library.A more frequent case is that a free library does the samejob as widely used non-free libraries. In this case, there islittle to gain by limiting the free library to free softwareonly, so we use the Lesser General Public License.

In other cases, permission to use a particular library innon-free programs enables a greater number of people touse a large body of free software. For example,permission to use the GNU C Library in non-free programsenables many more people to use the whole GNUoperating system, as well as its variant, the GNU/Linuxoperating system.

Although the Lesser General Public License is Lessprotective of the users’ freedom, it does ensure that theuser of a program that is linked with the Library has thefreedom and the wherewithal to run that program using amodified version of the Library.

The precise terms and conditions for copying, distributionand modification follow. Pay close attention to thedifference between a “work based on the library” and a“work that uses the library”. The former contains codederived from the library, whereas the latter must becombined with the library in order to run.

GNU LESSER GENERAL PUBLIC LICENSETERMS AND CONDITIONS FOR COPYING,DISTRIBUTION AND MODIFICATION0. This License Agreement applies to any software library

or other program which contains a notice placed by thecopyright holder or other authorized party saying it maybe distributed under the terms of this Lesser GeneralPublic License (also called “this License”). Eachlicensee is addressed as “you”.

A “library” means a collection of software functions and/or

40

LGPL (continued)

data prepared so as to be conveniently linked withapplication programs (which use some of those functionsand data) to form executables.

The “Library”, below, refers to any such software library orwork which has been distributed under these terms. A“work based on the Library” means either the Library orany derivative work under copyright law: that is to say, awork containing the Library or a portion of it, eitherverbatim or with modifications and/or translatedstraightforwardly into another language. (Hereinafter,translation is included without limitation in the term“modification”.)

“Source code” for a work means the preferred form of thework for making modifications to it. For a library, completesource code means all the source code for all modules itcontains, plus any associated interface definition files, plusthe scripts used to control compilation and installation ofthe library.

Activities other than copying, distribution and modificationare not covered by this License; they are outside itsscope. The act of running a program using the Library isnot restricted, and output from such a program is coveredonly if its contents constitute a work based on the Library(independent of the use of the Library in a tool for writingit). Whether that is true depends on what the Library doesand what the program that uses the Library does.

1. You may copy and distribute verbatim copies of theLibrary’s complete source code as you receive it, in anymedium, provided that you conspicuously andappropriately publish on each copy an appropriatecopyright notice and disclaimer of warranty; keep intactall the notices that refer to this License and to theabsence of any warranty; and distribute a copy of thisLicense along with the Library.

You may charge a fee for the physical act of transferring acopy, and you may at your option offer warranty protectionin exchange for a fee.

2. You may modify your copy or copies of the Library orany portion of it, thus forming a work based on theLibrary, and copy and distribute such modifications orwork under the terms of Section 1 above, provided thatyou also meet all of these conditions:

a) The modified work must itself be a software library.

b) You must cause the files modified to carry prominentnotices stating that you changed the files and thedate of any change.

c) You must cause the whole of the work to be licensedat no charge to all third parties under the terms of thisLicense.

d) If a facility in the modified Library refers to a functionor a table of data to be supplied by an applicationprogram that uses the facility, other than as anargument passed when the facility is invoked, thenyou must make a good faith effort to ensure that, inthe event an application does not supply suchfunction or table, the facility still operates, andperforms whatever part of its purpose remainsmeaningful.

(For example, a function in a library to compute squareroots has a purpose that is entirely well-definedindependent of the application. Therefore, Subsection2d requires that any application-supplied function or

table used by this function must be optional: if theapplication does not supply it, the square root functionmust still compute square roots.)

These requirements apply to the modified work as awhole. If identifiable sections of that work are not derivedfrom the Library, and can be reasonably consideredindependent and separate works in themselves, then thisLicense, and its terms, do not apply to those sectionswhen you distribute them as separate works. But whenyou distribute the same sections as part of a whole whichis a work based on the Library, the distribution of thewhole must be on the terms of this License, whosepermissions for other licensees extend to the entire whole,and thus to each and every part regardless of who wroteit.

Thus, it is not the intent of this section to claim rights orcontest your rights to work written entirely by you; rather,the intent is to exercise the right to control the distributionof derivative or collective works based on the Library.

In addition, mere aggregation of another work not basedon the Library with the Library (or with a work based onthe Library) on a volume of a storage or distributionmedium does not bring the other work under the scope ofthis License.

3. You may opt to apply the terms of the ordinary GNUGeneral Public License instead of this License to agiven copy of the Library. To do this, you must alter allthe notices that refer to this License, so that they referto the ordinary GNU General Public License, version 2,instead of to this License. (If a newer version thanversion 2 of the ordinary GNU General Public Licensehas appeared, then you can specify that version insteadif you wish.) Do not make any other change in thesenotices.

Once this change is made in a given copy, it is irreversiblefor that copy, so the ordinary GNU General Public Licenseapplies to all subsequent copies and derivative worksmade from that copy.

This option is useful when you wish to copy part of thecode of the Library into a program that is not a library.

4. You may copy and distribute the Library (or a portion orderivative of it, under Section 2) in object code orexecutable form under the terms of Sections 1 and 2above provided that you accompany it with thecomplete corresponding machine-readable sourcecode, which must be distributed under the terms ofSections 1 and 2 above on a medium customarily usedfor software interchange.

If distribution of object code is made by offering access tocopy from a designated place, then offering equivalentaccess to copy the source code from the same placesatisfies the requirement to distribute the source code,even though third parties are not compelled to copy thesource along with the object code.

5. A program that contains no derivative of any portion ofthe Library, but is designed to work with the Library bybeing compiled or linked with it, is called a “work thatuses the Library”. Such a work, in isolation, is not aderivative work of the Library, and therefore falls outsidethe scope of this License.

However, linking a “work that uses the Library” with theLibrary creates an executable that is a derivative of theLibrary (because it contains portions of the Library), rather

41

LGPL (continued)

than a “work that uses the library”. The executable istherefore covered by this License. Section 6 states termsfor distribution of such executables.

When a “work that uses the Library” uses material from aheader file that is part of the Library, the object code forthe work may be a derivative work of the Library eventhough the source code is not. Whether this is true isespecially significant if the work can be linked without theLibrary, or if the work is itself a library. The threshold forthis to be true is not precisely defined by law.

If such an object file uses only numerical parameters, datastructure layouts and accessors, and small macros andsmall inline functions (ten lines or less in length), then theuse of the object file is unrestricted, regardless of whetherit is legally a derivative work. (Executables containing thisobject code plus portions of the Library will still fall underSection 6.)

Otherwise, if the work is a derivative of the Library, youmay distribute the object code for the work under theterms of Section 6. Any executables containing that workalso fall under Section 6, whether or not they are linkeddirectly with the Library itself.

6. As an exception to the Sections above, you may alsocombine or link a “work that uses the Library” with theLibrary to produce a work containing portions of theLibrary, and distribute that work under terms of yourchoice, provided that the terms permit modification ofthe work for the customer’s own use and reverseengineering for debugging such modifications.

You must give prominent notice with each copy of thework that the Library is used in it and that the Library andits use are covered by this License. You must supply acopy of this License. If the work during execution displayscopyright notices, you must include the copyright notice forthe Library among them, as well as a reference directingthe user to the copy of this License. Also, you must doone of these things:

a) Accompany the work with the completecorresponding machine-readable source code for theLibrary including whatever changes were used in thework (which must be distributed under Sections 1and 2 above); and, if the work is an executable linkedwith the Library, with the complete machine-readable“work that uses the Library”, as object code and/orsource code, so that the user can modify the Libraryand then relink to produce a modified executablecontaining the modified Library. (It is understood thatthe user who changes the contents of definitions filesin the Library will not necessarily be able to recompilethe application to use the modified definitions.)

b) Use a suitable shared library mechanism for linkingwith the Library. A suitable mechanism is one that (1)uses at run time a copy of the library already presenton the user's computer system, rather than copyinglibrary functions into the executable, and (2) willoperate properly with a modified version of thelibrary, if the user installs one, as long as themodified version is interface-compatible with theversion that the work was made with.

c) Accompany the work with a written offer, valid for atleast three years, to give the same user the materialsspecified in Subsection 6a, above, for a charge nomore than the cost of performing this distribution.

d) If distribution of the work is made by offering accessto copy from a designated place, offer equivalentaccess to copy the above specified materials fromthe same place.

e) Verify that the user has already received a copy ofthese materials or that you have already sent thisuser a copy.

For an executable, the required form of the “work thatuses the Library” must include any data and utilityprograms needed for reproducing the executable from it.However, as a special exception, the materials to bedistributed need not include anything that is normallydistributed (in either source or binary form) with the majorcomponents (compiler, kernel, and so on) of the operatingsystem on which the executable runs, unless thatcomponent itself accompanies the executable.

It may happen that this requirement contradicts the licenserestrictions of other proprietary libraries that do notnormally accompany the operating system. Such acontradiction means you cannot use both them and theLibrary together in an executable that you distribute.

7. You may place library facilities that are a work based onthe Library side-by-side in a single library together withother library facilities not covered by this License, anddistribute such a combined library, provided that theseparate distribution of the work based on the Libraryand of the other library facilities is otherwise permitted,and provided that you do these two things:

a) Accompany the combined library with a copy of thesame work based on the Library, uncombined withany other library facilities. This must be distributedunder the terms of the Sections above.

b) Give prominent notice with the combined library ofthe fact that part of it is a work based on the Library,and explaining where to find the accompanyinguncombined form of the same work.

8. You may not copy, modify, sublicense, link with, ordistribute the Library except as expressly providedunder this License. Any attempt otherwise to copy,modify, sublicense, link with, or distribute the Library isvoid, and will automatically terminate your rights underthis License. However, parties who have receivedcopies, or rights, from you under this License will nothave their licenses terminated so long as such partiesremain in full compliance.

9. You are not required to accept this License, since youhave not signed it. However, nothing else grants youpermission to modify or distribute the Library or itsderivative works. These actions are prohibited by law ifyou do not accept this License. Therefore, by modifyingor distributing the Library (or any work based on theLibrary), you indicate your acceptance of this License todo so, and all its terms and conditions for copying,distributing or modifying the Library or works based onit.

10. Each time you redistribute the Library (or any workbased on the Library), the recipient automaticallyreceives a license from the original licensor to copy,distribute, link with or modify the Library subject tothese terms and conditions. You may not impose anyfurther restrictions on the recipients’ exercise of therights granted herein. You are not responsible forenforcing compliance by third parties with this License.

42

LGPL (continued)

11. If, as a consequence of a court judgment or allegationof patent infringement or for any other reason (notlimited to patent issues), conditions are imposed onyou (whether by court order, agreement or otherwise)that contradict the conditions of this License, they donot excuse you from the conditions of this License. Ifyou cannot distribute so as to satisfy simultaneouslyyour obligations under this License and any otherpertinent obligations, then as a consequence you maynot distribute the Library at all. For example, if a patentlicense would not permit royalty-free redistribution ofthe Library by all those who receive copies directly orindirectly through you, then the only way you couldsatisfy both it and this License would be to refrainentirely from distribution of the Library.

If any portion of this section is held invalid orunenforceable under any particular circumstance, thebalance of the section is intended to apply, and the sectionas a whole is intended to apply in other circumstances.

It is not the purpose of this section to induce you toinfringe any patents or other property right claims or tocontest validity of any such claims; this section has thesole purpose of protecting the integrity of the free softwaredistribution system which is implemented by public licensepractices. Many people have made generous contributionsto the wide range of software distributed through thatsystem in reliance on consistent application of thatsystem; it is up to the author/donor to decide if he or she iswilling to distribute software through any other system anda licensee cannot impose that choice.

This section is intended to make thoroughly clear what isbelieved to be a consequence of the rest of this License.

12. If the distribution and/or use of the Library is restrictedin certain countries either by patents or by copyrightedinterfaces, the original copyright holder who places theLibrary under this License may add an explicitgeographical distribution limitation excluding thosecountries, so that distribution is permitted only in oramong countries not thus excluded. In such case, thisLicense incorporates the limitation as if written in thebody of this License.

13. The Free Software Foundation may publish revisedand/or new versions of the Lesser General PublicLicense from time to time. Such new versions will besimilar in spirit to the present version, but may differ indetail to address new problems or concerns.

Each version is given a distinguishing version number. Ifthe Library specifies a version number of this Licensewhich applies to it and “any later version”, you have theoption of following the terms and conditions either of thatversion or of any later version published by the FreeSoftware Foundation. If the Library does not specify alicense version number, you may choose any version everpublished by the Free Software Foundation.

14. If you wish to incorporate parts of the Library into otherfree programs whose distribution conditions areincompatible with these, write to the author to ask forpermission. For software which is copyrighted by theFree Software Foundation, write to the Free SoftwareFoundation; we sometimes make exceptions for this.Our decision will be guided by the two goals ofpreserving the free status of all derivatives of our freesoftware and of promoting the sharing and reuse ofsoftware generally.

NO WARRANTY15. BECAUSE THE LIBRARY IS LICENSED FREE OF

CHARGE, THERE IS NO WARRANTY FOR THELIBRARY, TO THE EXTENT PERMITTED BYAPPLICABLE LAW. EXCEPT WHEN OTHERWISESTATED IN WRITING THE COPYRIGHT HOLDERSAND/OR OTHER PARTIES PROVIDE THE LIBRARY“AS IS” WITHOUT WARRANTY OF ANY KIND,EITHER EXPRESSED OR IMPLIED, INCLUDING,BUT NOT LIMITED TO, THE IMPLIED WARRANTIESOF MERCHANTABILITY AND FITNESS FOR APARTICULAR PURPOSE. THE ENTIRE RISK AS TOTHE QUALITY AND PERFORMANCE OF THELIBRARY IS WITH YOU. SHOULD THE LIBRARYPROVE DEFECTIVE, YOU ASSUME THE COST OFALL NECESSARY SERVICING, REPAIR ORCORRECTION.

16. IN NO EVENT UNLESS REQUIRED BY APPLICABLELAW OR AGREED TO IN WRITING WILL ANYCOPYRIGHT HOLDER, OR ANY OTHER PARTYWHO MAY MODIFY AND/OR REDISTRIBUTE THELIBRARY AS PERMITTED ABOVE, BE LIABLE TOYOU FOR DAMAGES, INCLUDING ANY GENERAL,SPECIAL, INCIDENTAL OR CONSEQUENTIALDAMAGES ARISING OUT OF THE USE ORINABILITY TO USE THE LIBRARY (INCLUDING BUTNOT LIMITED TO LOSS OF DATA OR DATA BEINGRENDERED INACCURATE OR LOSSESSUSTAINED BY YOU OR THIRD PARTIES OR AFAILURE OF THE LIBRARY TO OPERATE WITHANY OTHER SOFTWARE), EVEN IF SUCH HOLDEROR OTHER PARTY HAS BEEN ADVISED OF THEPOSSIBILITY OF SUCH DAMAGES.

END OF TERMS AND CONDITIONS

43

OpenSSL LicenseLICENSE ISSUES

The OpenSSL toolkit stays under a dual license, i.e. boththe conditions of the OpenSSL License and the originalSSLeay license apply to the toolkit.See below for the actual license texts. Actually bothlicenses are BSD-style Open Source licenses. In case ofany license issues related to OpenSSL please [email protected].

OpenSSL License

Copyright (c) 1998-2002 The OpenSSL Project. All rightsreserved.Redistribution and use in source and binary forms, with orwithout modification, are permitted provided that thefollowing conditions are met:

1. Redistributions of source code must retain the abovecopyright notice, this list of conditions and the followingdisclaimer.

2. Redistributions in binary form must reproduce the abovecopyright notice, this list of conditions and the followingdisclaimer in the documentation and/or other materialsprovided with the distribution.

3. All advertising materials mentioning features or use ofthis software must display the followingacknowledgment: “This product includes softwaredeveloped by the OpenSSL Project for use in theOpenSSL Toolkit. (http://www.openssl.org/)”

4. The names “OpenSSL Toolkit” and “OpenSSL Project”must not be used to endorse or promote productsderived from this software without prior writtenpermission. For written permission, please [email protected].

5. Products derived from this software may not be called“OpenSSL” nor may “OpenSSL” appear in their nameswithout prior written permission of the OpenSSL Project.

6. Redistributions of any form whatsoever must retain thefollowing acknowledgment: “This product includessoftware developed by the OpenSSL Project for use inthe OpenSSL Toolkit (http://www.openssl.org/)”

THIS SOFTWARE IS PROVIDED BY THE OpenSSLPROJECT “AS IS” AND ANY EXPRESSED OR IMPLIEDWARRANTIES, INCLUDING, BUT NOT LIMITED TO,THE IMPLIED WARRANTIES OF MERCHANTABILITYAND FITNESS FOR A PARTICULAR PURPOSE AREDISCLAIMED. IN NO EVENT SHALL THE OpenSSLPROJECT OR ITS CONTRIBUTORS BE LIABLE FORANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,EXEMPLARY, OR CONSEQUENTIAL DAMAGES(INCLUDING, BUT NOT LIMITED TO, PROCUREMENTOF SUBSTITUTE GOODS OR SERVICES; LOSS OFUSE, DATA, OR PROFITS; OR BUSINESSINTERRUPTION) HOWEVER CAUSED AND ON ANYTHEORY OF LIABILITY, WHETHER IN CONTRACT,STRICT LIABILITY, OR TORT (INCLUDINGNEGLIGENCE OR OTHERWISE) ARISING IN ANY WAYOUT OF THE USE OF THIS SOFTWARE, EVEN IFADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

This product includes cryptographic software written byEric Young ([email protected]). This product includessoftware written by Tim Hudson ([email protected]).

Original SSLeay License

Copyright (C) 1995-1998 Eric Young ([email protected])All rights reserved.

This package is an SSL implementation written by EricYoung ([email protected]).The implementation was written so as to conform withNetscapes SSL.This library is free for commercial and non-commercial useas long as the following conditions are aheared to. Thefollowing conditions apply to all code found in thisdistribution, be it the RC4, RSA, lhash, DES, etc., code;not just the SSL code. The SSL documentation includedwith this distribution is covered by the same copyrightterms except that the holder is Tim Hudson([email protected]).Copyright remains Eric Young ’s, and as such anyCopyright notices in the code are not to be removed.If this package is used in a product, Eric Young should begiven attribution as the author of the parts of the libraryused.This can be in the form of a textual message at programstartup or in documentation (online or textual) providedwith the package.Redistribution and use in source and binary forms, with orwithout modification, are permitted provided that thefollowing conditions are met:

1. Redistributions of source code must retain the copyrightnotice, this l ist of condit ions and the followingdisclaimer.


3. All advertising materials mentioning features or use ofthis software must display the followingacknowledgement: “This product includes cryptographicsoftware written by Eric Young ([email protected])”The word “cryptographic” can be left out if the rouinesfrom the library being used are not cryptographicrelated :-).

4. If you include any Windows specif ic code (or aderivative thereof) from the apps directory (applicationcode) you must include an acknowledgement: “Thisproduct includes software written by Tim Hudson([email protected])”

THIS SOFTWARE IS PROVIDED BY ERIC YOUNG “ASIS” AND ANY EXPRESS OR IMPLIED WARRANTIES,INCLUDING, BUT NOT LIMITED TO, THE IMPLIEDWARRANTIES OF MERCHANTABILITY AND FITNESSFOR A PARTICULAR PURPOSE ARE DISCLAIMED. INNO EVENT SHALL THE AUTHOR OR CONTRIBUTORSBE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,SPECIAL, EXEMPLARY, OR CONSEQUENTIALDAMAGES (INCLUDING, BUT NOT LIMITED TO,PROCUREMENT OF SUBSTITUTE GOODS ORSERVICES; LOSS OF USE, DATA, OR PROFITS; ORBUSINESS INTERRUPTION) HOWEVER CAUSED ANDON ANY THEORY OF LIABILITY, WHETHER INCONTRACT, STRICT LIABILITY, OR TORT (INCLUDINGNEGLIGENCE OR OTHERWISE) ARISING IN ANY WAYOUT OF THE USE OF THIS SOFTWARE, EVEN IFADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

The licence and distribution terms for any publicallyavailable version or derivative of this code cannot bechanged. i.e. this code cannot simply be copied and putunder another distribution licence [including the GNUPublic Licence.]

44

Blowfish License

DES License


This package is an Blowfish implementation written by EricYoung ([email protected]).

This library is free for commercial and non-commercial useas long as the following conditions are aheared to. Thefollowing conditions apply to all code found in thisdistribution.

Copyright remains Eric Young's, and as such anyCopyright notices in the code are not to be removed.

Redistribution and use in source and binary forms, with orwithout modification, are permitted provided that thefollowing conditions are met:



3. All advertising materials mentioning features or use ofthis software must display the followingacknowledgement:This product includes software developed by EricYoung ([email protected]).


This package is an DES implementation written by EricYoung ([email protected]).The implementation was written so as to conform withMIT’s libdes.

This library is free for commercial and non-commercial useas long as the following conditions are aheared to. Thefollowing conditions apply to all code found in thisdistribution.

Copyright remains Eric Young ’s, and as such anyCopyright notices in the code are not to be removed.If this package is used in a product, Eric Young should begiven attribution as the author of that the SSL library. Thiscan be in the form of a textual message at program startupor in documentation (online or textual) provided with thepackage.

Redistribution and use in source and binary forms, with orwithout modification, are permitted provided that thefollowing conditions are met:



3. All advertising materials mentioning features or use ofthis software must display the following

acknowledgement:This product includes software developed by Eric Young([email protected])


The license and distribution terms for any publicallyavailable version or derivative of this code cannot bechanged. i.e. this code cannot simply be copied and putunder another distrubution license [including the GNUPublic License.]

The reason behind this being stated in this direct manneris past experience in code simply being copied and theattribution removed from it and then being distributed aspart of other packages. This implementation was a non-trivial and unpaid effort.


The license and distribution terms for any publicallyavailable version or derivative of this code cannot bechanged. i.e. this code cannot simply be copied and putunder another distrubution license [including the GNUPublic License.]

The reason behind this being stated in this direct manneris past experience in code simply being copied and theattribution removed from it and then being distributed aspart of other packages. This implementation was a non-trivial and unpaid effort.

45

Specifications

Power requirements: 12 V DC (11 V - 15 V DC)

Input current: 0.9 A

indicates a safety related item.

Operating temperature:32 ˚F to 113 ˚F (0 ˚C to 45 ˚C)

Operating humidity:10 % to 80 % (no condensation)

Mass(recorder): 2.49 lb (1130 g)(camera): 1.15 lb (520 g)

Dimensions (W x H x D)(excluding protruding parts andrecorder mount adapters)(recorder):7 inches x1-31/32 inches x6-3/32 inches(178 mm x 50 mm x 155 mm)(camera):2-27/32 inches x3-7/32 inches x6-17/32 inches(72 mm x 82 mm x 166 mm)

Video format:NTSC(525 lines, 60 fields)

Recording media:P2 card

Recording format:Proprietary format

Video compression:MPEG4

Audio compression:G.726 2-channel

Recording time:Approx. 32 hours (max.)(using two 4-GB P2 cards at 512 kbps)

1 512 k approx.8

2 512 k approx.16

1 1 M approx.4

2 1 M approx.8

1 512 k approx.16

2 512 k approx.32

1 1 M approx.8

2 1 M approx.16

2 GB

4 GB

Card modelnumber Capacity Number

of cardsRecordingrate (bps)

Recordingtime (hours)

AJ-P2C002SG

AJ-P2C004HG

VideoInputs:

Line (CAMERA connector) x 11.0 Vp-p, 75 Ω, unbalanced

Line (Pin jack) x 11.0 Vp-p, 75 Ω, unbalanced

Output: (outputs an original input signal)Line (Pin jack) x 1

1.0 Vp-p, 75 Ω, unbalanced

AudioInputs:

Line (Pin jack) x 2–10 dBV, 47 kΩ, unbalanced

Microphone (Pin jack) x 1

–50 dBV, 3 kΩ, unbalanced(plug-in power 4.5 V)

DC IN connectorSIGNAL port

Input voltage L: 1.0 VH: 8 V- 15 V

Input current: 1 mA (max.)

Other I/O connectorsGPIO/SERIAL portRS-232CGPIO

Inputs: 8 portsInput voltage L: 1.0 V

H: 4 V- 15 VInput current: 15 mA (max.)

Output: 1 portOutput voltage: 5.0 VOutput current: 15 mA

CAMERA connector10/100 Mbps Ethernet (RJ-45)

General Recorder

46

Specifications (continued)

Image sensor1/4 inch CCD380,000 pixels (efective area)

LensFocal length

(optical zoom x22, digital zoom x10)(without wide conversion lens):f = 3.79 mm - 83.4 mm(With wide conversion lens):f = 2.65 mm - 58.4 mm

Maximum aperture ratio:F1.6 (WIDE) - F3.0 (TELE)

Field angle(without wide conversion lens):(Horizontal) 2.6 ˚ (TELE) - 52.3 ˚ (WIDE)(With wide conversion lens):(Horizontal) 3.5 ˚ (TELE) - 68.4 ˚ (WIDE)

Sensitivity0.7 lx (Color, AGC HIGH, SENS UP off)0.04 lx (B/W, AGC HIGH, SENS UP off)

Camera

47

LIMITED WARRANTY

For U.S.A.

Panasonic Computer Solutions Company (referred to as “Panasonic”) at it’s sole discretion,will replace or repair the below listed “Arbitrator” video system product components with newor rebuilt parts, free of charge in the U.S.A. for the period specified below from the date oforiginal purchase in the event of a defect in materials or workmanship. Coverage does notinclude wear or cosmetic damage. Lost items are also not covered under the warranty.

1 Year - Video Camera1 Year - Recorder Unit1 Year - Wireless Receiver Unit1 Year – P2 Card(s) (All Sizes)90 Days - Wireless Microphone(s)90 Days - All System Component Interconnect Cables

This warranty is extended solely to the original purchaser. A purchase receipt or other proofof date of original purchase will be required before warranty performance is rendered.

This warranty only covers failures due to defects in materials or workmanship which occurduring normal use. It does not cover damage which occurs in shipment or failures which arecaused by products not supplied by Panasonic, or failures which result from alteration,accident, misuse, introduction of liquid or other foreign matter into the unit, abuse, neglect,installation, maladjustment of consumer controls, improper maintenance, modification orservice by anyone other than a Factory Service Center or authorized Panasonic ServiceDealer, or damage that is attributable to acts of God or War.

Limits and Exclusions:

There are no other express warranties except as listed above.

PANASONIC SHALL NOT BE LIABLE FOR LOSS OF DATA OR OTHER INCIDENTAL ORCONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THIS PRODUCT, ORARISING OUT OF ANY BREACH OF THIS WARRANTY. ALL EXPRESS AND IMPLIEDWARRANTIES, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESSFOR A PARTICULAR PURPOSE ARE LIMITED TO THE APPLICABLE WARRANTYPERIOD SET FORTH ABOVE. Some states do not allow the exclusion or limitation ofincidental or consequential damages, or limitations on how long an implied warranty lasts, sothe above limitations or exclusions may not apply to you.

This limited warranty gives you specific legal rights, and you may also have other rightswhich vary from state to state.

If a problem with your product develops during or after the warranty period, you may contactour representatives at 1-800-LAPTOP5.

Video System Hardware LIMITED WARRANTY

memory card video recording system · lines), record tally output (1 line), and serial port. dc in...

Documents