meshing tutorial 3d-bushing v81 601b
TRANSCRIPT
-
8/8/2019 Meshing Tutorial 3d-Bushing v81 601b
1/7
Nyquist/ Haghighi
1
ANSYS Meshing Tutorial
This example creates a 3-D solid model of a centering bushing.
All dimensions are in inches.
-
8/8/2019 Meshing Tutorial 3d-Bushing v81 601b
2/7
Nyquist/ Haghighi
2
The following is the step-by-step procedure for the meshing tutorial using the ANSYS GUI (GraphicUser Interface) environment. Using the left button of the mouse, click on everything that is typed boldand type everything that is italicizedbelow.
(Go To ANSYS/Faculty Utility Menu)File
Change Jobname then type Bushing
PlotCtrlsNumbering
(Go to LINE and click) OFF (then OFF will be toggled to ON)(Go to AREA and click) OFF (then OFF will be toggled to ON)OK
(Go To Main Menu)Preprocessor
ModelingCreate
AreaRectangle
By 2 Corners(X box)0.56(Y box) 0(Width box) 1.12(Height box) 1.24& OK
LinesLine Fillet
(Pick lines L2 & L3) & OK(Radius box) 0.2& Apply
(Pick lines L3 & L4) & OK(Radius box) 0.2& OK
OperateBooleans
DivideArea by Line
(Pick area to be divided) Click A1 (rectangle) & Apply(Pick dividing lines) Click on L5 and L8 (fillets) & OK
(Note: A warning box may appear stating that Line 8 is attached to 2 areas and
can not be deleted. Click OK.)
DeleteAreas & Below
(Pick areas A2 & A3) & OK
CreateArea
RectangleBy 2 Corners
-
8/8/2019 Meshing Tutorial 3d-Bushing v81 601b
3/7
Nyquist/ Haghighi
3
(X box)0.24(Y box) 1.24(Width box) 0.48(Height box) 0.4475& OK
CircleSolid Circle
(X box) 0(Y box) 1.6875(Rad1 box) 0.24& OK
OperateBooleans
AddAreas
(Click on A1, A2, A4 the circle and 2 rectangles) & OK
CreateArea
CircleAnnulus
(X box) 0(Y box) 0(Rad1 box) 0.6875(Rad2 box) 1 & Apply
(X box) 0(Y box) 0(Rad1 box) 1(Rad2 box) 2.375& OK
OperateBooleans
SubtractAreas
(Click on base area from which to subtract) Click A1, A2 (annuli) & Apply(Click on area to be subtracted) Click A3 (rectangular slot) & OK
CreateArea
CircleSolid Circle
(X box) 1.6875
(Y box) 0(Rad1 box) 0.375& Apply
(X box)1.6875(Y box) 0(Rad1 box) 0.375& Apply
(X box) 0(Y box)1.6875(Rad1 box) 0.375& OK
-
8/8/2019 Meshing Tutorial 3d-Bushing v81 601b
4/7
Nyquist/ Haghighi
4
Operate
BooleansSubtract
Areas(Click on base area from which to subtract) Click A5 (annulus) & Apply(Click on area to be subtracted) Click A1, A2, A3 (3 small circles) & OK
ExtrudeAreas
Along Normal(Click on area 1) Click on A4 (small annulus) & Apply
(DIST length of extrusion) 2.62& OK
(Go To Utility Menu)Plot
Areas
(Go To Main Menu)
PreprocessorModeling
OperateExtrude
AreasAlong Normal
(Click on area 3) Click on the A6 (large annulus) & Apply(DIST length of extrusion) 0.62& Apply
(Go To Utility Menu)File
Save as Jobname.db (Check the working directory)
PlotVolumes
(Go To Main Menu)Preprocessor
Element TypeAdd/Edit/Delete
AddStructural & Solid & Tet 10 node 92 & OK
Close Element Type window
(Go To Preprocessor)MeshTool
Use the Area, Line and Volume commands to create a mesh for the bushing.
-
8/8/2019 Meshing Tutorial 3d-Bushing v81 601b
5/7
Nyquist/ Haghighi
5
-
8/8/2019 Meshing Tutorial 3d-Bushing v81 601b
6/7
Nyquist/ Haghighi
6
-
8/8/2019 Meshing Tutorial 3d-Bushing v81 601b
7/7
Nyquist/ Haghighi
7