metra group puvip® puvip® the vacuum insulation panel, with hybrid-system barrier film (without...
TRANSCRIPT
METRA GROUP
PUVIP®
The Vacuum Insulation Panel , with Hybrid-System barrier film (without edge effect) completely enveloped by the closed cell Polyurethane (PU) Foam as PUVIP®. In addition to the stable build, due PU-Foam, the energy efficiency loss is reduced, thus more lifetime is ensured. The long-term test over 5 years in our R&D Center proves that PUVIP® very low loss of thermal conductivity. The six sides of PUVIP® is very smooth, that is very easy to apply and the edges are without gap. PUVIP® allows a safe and easy application, without damaging a single panel.
PUVIP® has a lot of advantages, here are main points:•Minimum risk of damage•can not be bent and folded•impact and shock resistant•Long durability•very easy to apply•almost constant isolating effect•very robust against shock•waterproof, airtight•PUVIP® is suitable for each PU and saves 10 mm PU foam (Home Appliance)
Dimensions: The difference between the VIP size and the PUVIP® panel size:The thickness with PU Cover is additional 10mm (5mm+5mm) thicker than VIP 's thickness. The length and width is additional 30mm (15mm+15mm) longer than VIP’s.
Save Your Energy…
Aging Data of PUVIP®
Storage Condition of Samples: •Kept in Samples Room•Temperature: Room Temp (Approx 23 ). ℃•Humidity: Approx 75%•Produced Date: 2009-05-20, •The panel with Getter •No:R&D-1-F-724～ R&D-1-F-726
Measured Date vs K-factor for the PUVIP ® ( Total 5 Years )
Size of "PU-VIP Sheet" 2009-5-24 2009-12-28 2010-09-07 2011-12-28 2012-5-31 2013-8-3
A（ 1010*410*40
mm）3.64 3.72 3.43 3.42 3.58 3.72
B（ 1010*410*40
mm）3.64 3.63 3.35 3.41 3.52 3.71
C（ 1010*265*40
mm）3.63 3.72 3.45 3.43 3.61 3.81The K-factor was measured every year as the date below showing from May.29th, 2009 to Aug.03, 2013
Size of VIP (mm) VIP Initial K-factor (mW/m.K)
1000*400*15 3.01
1000*400*15 2.91
1000*255*15 2.92
Save Your Energy…METRA GROUP
PUVIP® is due to the PU foam cover and PHENOVIP® phenolic foam cover very safe and easy applicable everywhere of building. PHENOVIP® is developed for the higher fire protection requirements and unique Vacuum Insulation Panel in Flammability Class B1 (flame retardant) worldwide. In addition to the stable build, due PU-Foam / Phenolic-Foam, the energy efficiency loss is reduced, thus more lifetime is ensured. The long-term test over 5 years in our R&D Center proves that PUVIP® / PHENOVIP® very low loss of thermal conductivity. The six sides are very smooth, that is very easy to apply and the edges are without gap. PUVIP® / PNENOVIP® allows a safe and easy application, without damaging a single panel and no installation partner is necessary.
Save Your Energy…METRA GROUP
Application Areas of PUVIP® / PHENOVIP®
EIFS is very easy to apply without damaging a single PUVIP® / PHENOVIP®. It is easy to fix with dowels at the jointed Corner of Four panels. There is a circular area of 30mm diameter as PU / Phenol area. The remaining component of EIFS can be applied without special caution on PUVIP® / PHENOVIP®.
Save Your Energy…METRA GROUP
According to energy saving regulations, insulation in the existing buildings is also necessary.Old building renovation is very complicated. Most often, the external insulation by precious stucco facades, historic preservation, etc. is not possible.Interior insulation is the only alternative but the right insulation for everyday habitable areas are rare and very expensive.PUVIP® / PHENOVIP® is the excellent solution with the following arguments:•best price / performance ratio worldwide•best insulation effect worldwide•minimum area loss•no condensation•no mold between components (wall-PUVIP®)PUVIP ® / PHENOVIP® is as interior insulation in existing buildings very easily and seamlessly applied as tiles, since the six sides of the PUVIP® /PHENOVIP® are very smooth. PUVIP® / PHENOVIP® ensures optimal insulation on the historic buildings, stucco facades and half-timbered houses. No scaffolding and no planning application required.
Save Your Energy…METRA GROUP
Dimensions:PUVIP® is at four edges and 15mm at upper-lower surfaces each with 5 mm enveloped with PU foam. e.g. In PUVIP® with dimensions 500mm * 500mm * 30mm is integrated VIP panel with dimensions 470mm * 470mm * 20mm.
PUVIP® standard panel sizes:•250 mm x 250 mm,•250 mm x 500 mm, •500 mm x 500 mm •500 mm x 1000 mm Thickness of VIP: 10 mm, 15mm, 20mm and 25mm + additional 10mm PU-Foam (5mm+5mm)
Save Your Energy…METRA GROUP
470
Certification: Diameter of Fiberglass of the 2nd Generation VIP is approx 6 ～ 11 micron, which conforms to European Regulations, “Directive 67/548/EWG Note R, revised by Directive 97/69/EC Note Q” (the classification as carcinogenic material is not applicable to fibers with a length weighted geometric mean diameter minus two standard errors above the limit of 6 µm) Biopersistence Test Certificated by Fraunhofer Institute Hannover/Germany. Our products are certified to meet the stringent European requirements and German Hazardous Substances Ordinance.
Save Your Energy…METRA GROUP
VIP Specification
Thicknes range 5-35mm
Max. Size 1800 x 800mm
Diameter of Fiberglass6-11 micron (which conform to the European regulations)
The K-Factor 0.002 W/(mK) for mass production
Density 260-300kg
Temperature resistance -70°C - 80°C (due to the barrier film)
Only two companies have the Nano Getter Technology worldwide:1. Our Production Capacity: 10,000,000 pcs / month2. Company Production Capacity: 30,000 pcs / monthWe offer the getter to desiccant prices.
The Comparison of Absorption Performance between our Getter, E-getter and Desiccant
CONTACT:
TURKEYMetra Enerji Sistemleri Ltd. StiAngora is merkezi No:22Cayyolu 06530 AnkaraMr. Erol [email protected]
GERMANYMetra Energy Systems GmbHMarkt 45-4752062 AachenMr. Taner [email protected]
HONG KONGMetra Group Co., Ltd.Henan Bldg RM 170190 Jaffe RD [email protected]
Technical Support:Mr. Gurol [email protected]
Save Your Energy…METRA GROUP