micro-nano bubble generator ma5s · 2016. 9. 7. · micro-nano bubble generator ma5s operation...

6
MICRO-NANO BUBBLE GENERATOR M M A A 5 5 S S OPERATION MANUAL JPN PAT.3762206 JPN PAT.4694633 MANUFACTURED BY HACK UFB CO. LTD. Made in Japan Please read this manual carefully to operate the machine in safe manner.

Upload: others

Post on 31-Jan-2021

13 views

Category:

Documents


0 download

TRANSCRIPT

  • MMIICCRROO--NNAANNOO BBUUBBBBLLEE GGEENNEERRAATTOORR

    MMAA55SS OOPPEERRAATTIIOONN MMAANNUUAALL

    JPN PAT.№3762206

    JPN PAT.№4694633

    MANUFACTURED BY HACK UFB CO. LTD. Made in Japan

    Please read this manual carefully to operate the machine in safe manner.

  • Specifications

    Model: MA5S

    Outer dimensions: H360mm × W310mm × D130mm

    Weight: Approx. 7kg

    Power: AC 100v

    Power Frequency: 50/60 Hz

    Power Consumption: 1.3A

    Capacity: Adjustable up to 200-300cc/min.

    Caution

    1. Please DO NOT try to disassemble the machine.

    2. Make sure NOT to use loose electrical outlet.

    3. Make sure to connect the ground wire attached to the plug.

    Operation

    1. Make sure the machine is set on secure place.

    2. Make sure the hoses are connected to the right places.

    3. All the valves have been factory adjusted with tap water. Make necessary

    adjustment when you are using other liquids. (refer to Page 4)

    Note:

    � There might be splash of water come out from air release valve which is

    located at the top of the machine. This is normal as the machine is purging

    excess water and air.

    � Do not lift inlet hose from water surface during the operation.

  • 【Name of parts】

    Header

    Pressure gage

    ④ Stroke Knob, Scale

    ①①①① Outlet Valve

    ③③③③ Suction Valve ⑤⑤⑤⑤ Air Intake valve

    OUT←←←←

    IN→→→→

  • 【Set-up】

    We ship ① pump , ② mixing header and ③ piston pole

    separately packed to avoid any damages by transportation.

    Put ①the piston pole into the holes (

    See the pictures above ) to connect

    ①pump and ③mixing-header.

    White part should be covered by blue

    part (see the left picture ).

    Turn the screws in clockwise

    direction to fix.

  • 【How to operate】

    ① Push the switch to start. Be sure both tube are under the

    water.

    ② Set the pressure at0.5-1.0Mpa adjusting outlet valve.

    (Turn clockwise to close : Turn counter clockwise to open)

    ※ Althogh outlet Valve is already adjusted the best

    position when it is dispatched, it might be needed adjusted.

    Keep the pressure under 1.0Mpa, otherwise water is possibly

    leaking.

    【Position of other adjustment parts 】

    Suction Valve:Open 45 degrees from full open position

    Air Intake Valve:Open between 2 to 5

    Stroke Knob:5

    ※ These also have been adjusted before dispatching.You do not

    need to adjust these everytime , but it is possible a sensitive

    adjustment turning these valves and knob when use liquids other

    than water or highly viscous liquid.

    During operation, never stop at a certain

    position. Please look at the average.

    Switch

  • One (1) Year Limited Warranty

    Model: MA5S Serial No:

    Original Customer:

    Purchase Date:

    HACK UFB Co.,Ltd warrants this hardware product against defects in materials and workmanship under normal use for a period of ONE (1) YEAR from the date of purchase by the original end-user purchaser. If a hardware defect arises and a valid claim is received by Asupu within the Warranty Period, at its option and to the extent permitted by law, Asupu will either (1) repair the product at no charge, using new parts or parts equivalent to new in performance and reliability or (2) exchange the product with a product that is new or equivalent to new in performance and reliability and is at least functionally equivalent to the original product. Asupu may request that you replace defective parts with new or refurbished user-installable parts that Asupu provides in fulfillment of its warranty obligation.