mirror – power mirror control systemstuff.jaygroh.com/prius/prius info/official toyota info... ·...
TRANSCRIPT
MIRROR – POWER MIRROR CONTROL SYSTEM MI–1
MI
BODYMIRRORPOWER MIRROR CONTROL SYSTEMPARTS LOCATION
OUTER MIRROR SWITCH
OUTER REAR
VIEW MIRROR RH
OUTER REAR
VIEW MIRROR
LH
DRIVER SIDE JUNCTION BLOCK
- ACC FUSE
- AM2 FUSE
- ACC-B FUSE
Left/Right Adjustment
Switch
Outer Mirror Switch
ACC RELAY
B127647E01
MI–2 MIRROR – POWER MIRROR CONTROL SYSTEM
MI
SYSTEM DIAGRAM
M M M M
Outer Mirror Switch
Left
HL
MH MV M+ MH MV M+
SSW1 SSW2 HR VL VR M+ E
B
Left/
Up
RightRight/
Down
Mirror
Switch
Select
Switch
Up Down
from Multiplex Communication System
from Battery
from Battery
Power Source
Control ECU
AM2
AM1 ACCD
ACC-B
ACC
Outer Rear View
Mirror LHOuter Rear View
Mirror RH
ACC
B127648E01
MIRROR – POWER MIRROR CONTROL SYSTEM MI–3
MI
PROBLEM SYMPTOMS TABLEHINT:Use the table below to help determine the cause of the problem symptom. The potential causes of the symptoms are listed in order of probability in the "Suspected area" column of the table. Check each symptom by checking the suspected areas in the order they are listed. Replace parts as necessary.
Power mirror control systemSymptom Suspected area See page
Mirror does not operate
1. ACC fuse MI-1
2. AM2 fuse MI-1
3. ACC-B fuse MI-1
4. ACC relay MI-1
5. Outer mirror switch assembly MI-14
6. Outer rear view mirror assembly MI-10
7. Wire harness -
Mirror operates abnormally
1. ACC fuse MI-1
2. AM2 fuse MI-1
3. ACC-B fuse MI-1
4. ACC relay MI-1
5. Outer mirror switch assembly MI-14
6. Outer rear view mirror assembly MI-10
7. Wire harness -
MI–4 MIRROR – INNER REAR VIEW MIRROR
MI
BODYMIRRORINNER REAR VIEW MIRRORCOMPONENTS
INNER REAR VIEW MIRROR ASSEMBLY
INNER REAR VIEW MIRROR ASSEMBLY
INNER REAR VIEW
MIRROR COVER
w/ EC Mirror
B129178E01
MIRROR – INNER REAR VIEW MIRROR MI–5
MI
REMOVALHINT:EC mirror stands for "electrochromic mirror".1. REMOVE INNER REAR VIEW MIRROR ASSEMBLY
(w/o EC Mirror)(a) Push the cover in the direction indicated by the
arrows labeled A and remove it.(b) While holding down the claw in the direction
indicated by the black arrow labeled B, slide the mirror in the direction indicated by the white arrow and remove it.
2. REMOVE INNER REAR VIEW MIRROR ASSEMBLY (w/ EC Mirror)(a) Remove the inner rear view mirror cover.(b) Remove the screw.(c) Slide the mirror in the direction indicated by the
arrow in the illustration and remove the mirror.
A
A
Claw
Cover
B
B064964E02
B056435E02
MI–6 MIRROR – INNER REAR VIEW MIRROR
MI
INSPECTION1. INSPECT INNER REAR VIEW MIRROR ASSEMBLY
(w/ EC Mirror)(a) Check operation of the electrochromic inner mirror.
(1) Connect the battery's positive (+) lead to terminal 10 and the negative (-) lead to terminal 8.
(2) Attach black colored tape to the forward sensor to block it.
(3) Light up the mirror with an electric light, and check that the mirror surface changes from bright to dark.If the result is not as specified, replace the mirror assembly.
INSTALLATION1. INSTALL INNER REAR VIEW MIRROR ASSEMBLY
(w/o EC Mirror)(a) Install the mirror in the direction of the white arrow.(b) Install the cover as shown in the illustration.
Sensor
Black Colored Tape
Bright
Dark
Battery
8
10
B137708E04
Cover
Claw
B113835E01
MIRROR – INNER REAR VIEW MIRROR MI–7
MI
2. INSTALL INNER REAR VIEW MIRROR ASSEMBLY (w/ EC Mirror)(a) Install the mirror.(b) Install the screw.(c) Install the inner rear view mirror cover.
B056435E05
MI–8 MIRROR – OUTER REAR VIEW MIRROR
MI
BODYMIRROROUTER REAR VIEW MIRRORCOMPONENTS
DOOR PULL HANDLE
FRONT DOOR ARMREST
UPPER BASE PANEL
FRONT DOOR ARMREST
UPPER BASE PANEL
FRONT DOOR INSIDE
HANDLE BEZEL LH
FRONT DOOR LOWER FRAME
BRACKET GARNISH LH
FRONT DOOR TRIM BOARD
SUB-ASSEMBLY LH
OUTER REAR VIEW MIRROR ASSEMBLY LH
for RH Side
MIRROR COVER
MIRROR
5.5 (56, 49 in.*lbf)
N*m (kgf*cm, ft.*lbf) : Specified torque
B135938E01
MIRROR – OUTER REAR VIEW MIRROR MI–9
MI
REMOVALHINT:• Use the same procedures for the LH side and RH side.• The procedures listed below are for the LH side.
1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINALCAUTION:Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.
2. REMOVE FRONT DOOR INSIDE HANDLE BEZEL LH (See page ED-11)
3. REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH LH (See page ED-11)
4. REMOVE DOOR PULL HANDLE (See page ED-11)5. REMOVE FRONT DOOR ARMREST BASE PANEL
UPPER (See page ED-11)6. REMOVE FRONT DOOR TRIM BOARD SUB-
ASSEMBLY LH (See page ED-12)7. REMOVE OUTER REAR VIEW MIRROR ASSEMBLY
LH(a) Disconnect the mirror connector.(b) Remove the 3 nuts and mirror.
8. REMOVE OUTER REAR VIEW MIRROR ASSEMBLY LH(a) Using a moulding remover, detach the 4 claws and
outer rear view mirror.HINT:Apply protective tape to the mirror body.
B075148E01
Protective Tape
B137710E01
MI–10 MIRROR – OUTER REAR VIEW MIRROR
MI
(b) Disconnect the 2 connectors and remove the mirror.
(c) Using a screwdriver, detach the 6 claws and remove the mirror cover. HINT:Tape the screwdriver tip before use.
INSPECTION1. INSPECT OUTER REAR VIEW MIRROR ASSEMBLY
LH(a) Disconnect the mirror connector.(b) Apply battery voltage and check the operation of the
mirror.OK
If the result is not as specified, replace the mirror assembly.
B136005
B076118E01
(A)
(C)
(B)
(D)
MH
M+ MV
B070997E04
Measurement Condition Specified Condition
Battery positive (+) → Terminal 5 (MV) Battery negative (-) → Terminal 4 (M+)
Turns upward (A)
Battery positive (+) → Terminal 4 (M+) Battery negative (-) → Terminal 5 (MV)
Turns downward (B)
Battery positive (+) → Terminal 3 (MH) Battery negative (-) → Terminal 4 (M+)
Turns left (C)
Battery positive (+) → Terminal 4 (M+) Battery negative (-) → Terminal 3 (MH)
Turns right (D)
MIRROR – OUTER REAR VIEW MIRROR MI–11
MI
(c) Apply battery voltage to the mirror terminals and check the operation of the mirror heater.OK
If the result is not as specified, replace the mirror assembly.
2. INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH(a) Disconnect the mirror connector.(b) Apply battery voltage and check the operation of the
mirror.OK
If the result is not as specified, replace the mirror assembly.
(c) Apply battery voltage to the mirror terminals and check the operation of the mirror heater.OK
If the result is not as specified, replace the mirror assembly.
M-
M+
B076304E01
Measurement Condition Specified Condition
Battery positive (+) → Terminal 2 (M+) Battery negative (-) → Terminal 1 (M-)
Mirror becomes warm
(A)
(B)
(C) (D)
MH
MVM+B070998E03
Measurement Condition Specified Condition
Battery positive (+) → Terminal 5 (MV)Battery negative (-) → Terminal 4 (M+)
Turns upward (A)
Battery positive (+) → Terminal 4 (M+)Battery negative (-) → Terminal 5 (MV)
Turns downward (B)
Battery positive (+) → Terminal 3 (MH)Battery negative (-) → Terminal 4 (M+)
Turns left (C)
Battery positive (+) → Terminal 4 (M+)Battery negative (-) → Terminal 3 (MH)
Turns right (D)
M-
M+
B076303E01
Measurement Condition Specified Condition
Battery positive (+) → Terminal 2 (M+) Battery negative (-) → Terminal 1 (M-)
Mirror becomes warm
MI–12 MIRROR – OUTER REAR VIEW MIRROR
MI
INSTALLATION1. INSTALL OUTER MIRROR COVER LH
(a) Install the mirror cover as shown in the illustration.
(b) Check that there is no gap between the cover and mirror body.HINT:If there is a gap between the cover and body, noise will occur during driving.
(c) Connect the 2 connectors.
(d) Attach the 4 claws to install the mirror.
B075311E01
Mirror Body
Mirror Cover
B076333E01
B136005
B075313E01
MIRROR – OUTER REAR VIEW MIRROR MI–13
MI
2. INSTALL OUTER REAR VIEW MIRROR ASSEMBLY LH(a) Install the mirror with the 3 nuts.
Torque: 5.5 N*m (56 kgf*cm, 49 in.*lbf)(b) Connect the connector.
3. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH (See page ED-21)
4. INSTALL FRONT DOOR ARMREST BASE PANEL UPPER LH (See page ED-21)
5. INSTALL DOOR PULL HANDLE (See page ED-22)6. INSTALL FRONT DOOR LOWER FRAME BRACKET
GARNISH LH (See page ED-22)7. INSTALL FRONT DOOR INSIDE HANDLE BEZEL LH
(See page ED-22)8. PERFORM INITIALIZATION
(a) Perform initialization (see page SS-2).NOTICE:Certain systems need to be initialized after disconnecting and reconnecting the cable from the negative (-) battery terminal.
B075148E01
MI–14 MIRROR – OUTER MIRROR SWITCH
MI
OUTER MIRROR SWITCHINSPECTION1. INSPECT OUTER MIRROR SWITCH ASSEMBLY
(a) The L position of the left/right adjustment switch: Measure the resistance of the mirror switch.Standard resistance (for left side)
If the result is not as specified, replace the switch assembly.
(b) The R position of the left/right adjustment switch: Measure the resistance of the mirror switch.Standard resistance (for right side)
If the result is not as specified, replace the switch assembly.
LEFT RIGHT
Left/Right Adjustment Switch
Mirror
Switch
UP
LEFT RIGHT
DOWN
E MRV No PinNo Pin
MRHMLVMLHM+B
B059702E03
Tester Connection Switch Condition Specified Condition
4 (MLV) - 8 (B)6 (M+) - 7 (E)
UP Below 1 Ω
4 (MLV) - 7 (E) 6 (M+) - 8 (B)
DOWN Below 1 Ω
5 (MLH) - 8 (B) 6 (M+) - 7 (E)
LEFT Below 1 Ω
5 (MLH) - 7 (E) 6 (M+) - 8 (B)
RIGHT Below 1 Ω
Tester Connection Switch Condition Specified Condition
3 (MRV) - 8 (B) 6 (M+) - 7 (E)
UP Below 1 Ω
3 (MRV) - 7 (E) 6 (M+) - 8 (B)
DOWN Below 1 Ω
2 (MRH) - 8 (B) 6 (M+) - 7 (E)
LEFT Below 1 Ω
2 (MRH) - 7 (E) 6 (M+) - 8 (B)
RIGHT Below 1 Ω
MIRROR – MIRROR HEATER RELAY MI–15
MI
MIRROR HEATER RELAYON-VEHICLE INSPECTION1. INSPECT MIRROR HEATER RELAY
(a) Remove the mirror heater relay.(b) Measure the resistance of the relay.
Standard resistance
If the result is not as specified, replace the relay.(c) Install the mirror heater relay.
3
2
5
1
3
2
5
1
B060778E04
Tester Connection Specified Condition
3 - 5 10 kΩ or higher
Below 1 Ω(when battery voltage is applied to terminals 1 and 2)