mobile computing unit 2 -...
TRANSCRIPT
Mobile Computing Unit 2
TELE COMMUNICATIONS
Objective
This unit discusses the telecommunications systems which includes the GSM,
the GPRS, DECT. The basics of the Satellite networks, the Parameters and Configuration
and Capacity Allocation, the FAMA and DAMA. The Broadcast Systems like Digital
Audio Broadcasting and Digital Video Broadcasting are also being discussed.
Introduction
Digital cellular networks are the segment of the market for mobile and wireless
devices which are growing most rapidly. They are the wireless extensions of
traditional PSTN or ISDN networks and allow for seamless roaming with the same
mobile phone nation or even worldwide. Today, these systems are mainly used for
voice traffic. However, data traffic is continuously growing and, therefore, this
chapter presents several technologies for wireless data transmission using cellular
systems.
Global System for Mobile Communication (GSM):Rapid increase in the demand for data services, is the primary thrust for the
mobile industry to advance. However the radio access platforms that are different by
different service provides has been the inhibitor for the growth as there are a number
of different access 2 G technologies. International Telecommunications Union (ITU )
has specified the International Mobile Telecommunication 2000 (IMT 2000). IMT
2000 is the Radio and Network access specifications defining several methods or
technology platforms that meet the overall goals of the final specifications. It is meant to
be unifying specifications enabling mobile and fixed high speed data services to use
one or several radio channels with fixed network platforms for delivering the services
envisioned. Some IMT specifications are:
Global standard.
Compatibility of service within IMT 2000 and other fixed networks.
High quality
Worldwide common frequency band
Small terminals for worldwide use
Worldwide roaming capability
Multimedia application services and terminals
1
Mobile Computing Unit 2
Improved spectrum efficiency
Flexibility for evolution to the next generation of wireless systems.
High speed data rates.
2 Mbps for fixed environments
384 kbps for pedestrian
144 kbps for vehicular traffic
IN order to provide transition to 3 G technology different technology provider
were moving following different path so as to cater to the current 2G infrastructure
and the changes that need to be incorporated gradually to reach 3 G technology. Most
of these technologists have introduced a middle technology called 2. 5 G technology.
These are shown in the following diagram
MIGRATION PATH
General Packet Radio Service:
Provides higher data rate service
Same air interface as that of GSM is used.
GPRS defines a number of channel coding scheme
Coding
scheme
Air Interface Data Rate
Kbps
Usable data rate
CS 1 9.05 6.8
2
GSM (800,1900)
GPRS (800,1900)
EDGE (800,1900)
WCDMA
TD-SCDMA (CHINA)
TD-CDMA (JAPAN)
IS 95 CDMACDMA 20001x RTT
CDMA 2000 DO/DV
i DENWiDEN
Mobile Computing Unit 2
CS – 2 13.4 10.4CS-3 15.6 11.7CS – 4 21.4 16.0
If a single user access a multiple time slots, then speeds such as 40.2 ,
53.6 kbps becomes available. To the user
CS-2 has robust error correction over the air interface. CS - , 4 may
have higher data output rate, but have no error correction schemes
which may require retransmission leading wastage of transmission.
Biggest advantage of GPRS is not that it provides higher data rate, but it
facilitates packet switching wherein the network is connected as per
requirement rather than like in circuit switched for the full call
duration. When no data is transferred, channel is used by the other
users.
GPRS User devices:
The devices can transreceive both voice and data transmission. User may need
such service either separately or in combination. Accordingly, user can be grouped
into following classes.
a) Class A :
Supports simultaneous use of voice and data services. That is while holding
voice conversation, can download data at the same time.
b) Class B :
Supports simultaneous GPRS attach and GSM attach but not the
simultaneous use of both services. That is while downloading data, if a call a
received, the data download is put on hold and the voice call is attended.
Later down is resumed.
c) Class C :
Can attach eith GSM or GPRS but cannot attach both simultaneously. That is
at a given instant a class C device is either a GSM device or a GPRS device.
Other aspects of device are multislot capability of the device which directly
affects the supported data rate. Some device support three slot, others only two. As
the data down load requirement is asymmetric – high data rate in the down link
3
Mobile Computing Unit 2
and lower data rate in the uplink, some devices may have different slot for both up
and down link.
GPRS Air Interface:
Air interface is similar to GSM air interface. It is 200 KHz RF carrier and the
same eight slots per carrier. This allows both GSM and
GPRS to share the same RF resources. That is some slot may be carrying voice while
some slot may be carrying data.
Although GPRS makes use of the same basic infrastructure as GSM, it introduces
a number of logical channel types and new channel coding scheme. When the
GPRS related data traffic is handled, then it is known as Packet Data Channel
(PDCH) which has 52 frames per multiframe.
GPRS offers a point to point (PTP) packet service known as PTP CONS (Point to
Point Connection Oriented Network Service.) This is the ability of GPRS to maintain
the virtual circuit upon change of the cell with the GSM network. This type or
service corresponds to X.25 The other service PTP – CLNS – is the point to point
connection less network service that supports applications based on the internet
protocol IP.
GPRS Network Architecture:
4
Mobile Computing Unit 2
Details regarding various subsystems are given below:
PACKET CONTROL UNIT (PCF):
Responsible for a number of GPRS related functions such as air interface
access control, packet scheduling on the air interface and packet assembly and re
assembly. Located at BTS /BSC / SGSN
Serving GPRS Support Node (SGSN) :
Analogues to MSC / VLR of GSM. Performs MSC equivalent function in packet
switched domain – mobility management, security and access control etc. Service
area is divided into routing area – similar to location area. A SGSN may serve
multiple BSC, but each BSC will have only one SGSN. Various interfaces are shown
in the above diagram.
Gb interface SGSN ----- PCU :
Frame relay based interface that uses Base Station System GPRS Protocol
(BSSGP) – used to pass signaling, control information and data packet to and fro
from SGSN.
Gr interface between SGSN HLR :
5
Mobile Computing Unit 2
It uses Mobile Application Part (MAP) protocol. (similar to D interface between
a VLR and HLR). It is used to provide equipment identification, user authentication
and roaming and location updates to the HLR for GPRS subscribers. SGSN may also
retrieve the same information from HLR.
Gs interface between SGSN HLR :
SS7 based interface that used signaling, connection control part (SCCP).
Supports both circuit and packet switched services. This enables the coordination
between SGSN and MSC/VLR for subscribers of GPRS.
Gd interface between SGSN ----- SMSC:
Enables tran reception of SMS over GPRS. Uses SS 7 MAP protocol
Gn interface between SGSN ---- GGSN / SGSN:
It is internet protocol based interface carries signal and user data. This uses the
GPRS Tunneling Protocol GTP, which enables user data through the IP backbone
network between the SGSN and the GGSN.
Gateway GPRS Support Node (GGSN) :
It is a point of interface with external packet data network (such as internet).
Entry into and out of PLMN (Public Land Mobile Network) is through GGSN via Gn
interface. Gn is internet protocol based interface carries signaling and user data.
Gn interface uses GPRSs Tunneling Protocol (GTP), which tunnels the data through
IP backbone.
Gc interface between GGSN HLR :
It uses MAP (Mobile Application Part ) over SS7.It is used when GGSN wants to
know the serving SGSN for any subscriber.
GPRS Transmission Plane Protocol Reference Model:
6
Mobile Computing Unit 2
At the MS, there is RF interface, above which are Radio Link Control and
Medium Access Control functions. Above these are Logical Link Control (LLC) which
provides a logical link and framing structure for communication between the MS and
the SGSN. Any data between MS and SGSN is sent as Logical Link – Protocol Data Units
(LLPDU ). LLC supports management of this transfer, including mechanism for the
detection and recovery from, lost or corrupted LL-PDU, ciphering and flow control.
Above LLC, is Sub Network Dependent Convergence Protocol (SNDCP) which
resides between LLC and the network layer (such as IP and X.25) . The purpose of
SNDCP is to enable support for multiple network protocols without having to change
the lower layers such as LLC. It also help to multiplex several packet streams into a
single logical channel between MS and SGSN.
At the BSS, a relay function relays LL_PDU from Gb interface to the air interface
( the Um interface). Similarly, at SSGN, a relay function relays PDP PDUs between the
Gb interface and the Gn interface.
GTP- GPRS Tunneling Protocol: All data within GPRS backbone is transferred GTP.
It can use different transport protocols either the reliable TCP (needed for reliable
transfer of X.25 packets) or the non reliable UDP – used for packet IP. Tunneling is the
procedure of wrapping up the connection and its associated packets in a wrapper for
transmission through the IP network between GGSN and SGSN. In this case, the IP
network nodes (routers) between the SGSN and GGSN consider the GTP packets to be
application and those routers do not examine the contents of the GTP layer. At the
7
Mobile Computing Unit 2
SGSN, the wrapper is removed and the packet is passed to the MS using SNDCP, LLC
and the lower layers. For the packets from MS to external network- such as internet,
the GGSN removes the wrapper and forwards the IP packets.
Digital Enhanced Cordless Telecommunication (DECT)
It is specified by ETSI in 1998 -99. DECT is mainly used in offices, on campus, at
trade centers, or at home. Further access points to PSTN can be established within eg
at railway station, large government buildings and hospitals offering much cheaper
telephone services compared to a GSM
DECT may also provide last mile connectivity:
A big difference between the DECT and GSM is in terms of Cell diameter and
cell Capacity. While GSM can be used upto 70 KM, DECT is limited to 300 Meters
from the base station. DECT along with mobile station are cheap compared to that of
GSM.
The frequency range of DECT is 1880 – 1990 MHz offering 120 full duplex
channels. TDD is applied using 10 ms frames. The frequency range is divided into 10
carrier frequencies using FDMA each frame being divided into 24 slots using TDMA.
For the TDD mechanism, 12 slots are used for up link and 12 for down link. The digital
modulation technique used to GMSK. Each station has an average power of only 10
mw with a maximum of 250 mw.
System Architecture:
8
Mobile Computing Unit 2
Different DECT entities can be integrated into one physical unit or entities can
be distribute, replicated etc. However, the basic reference model is shown above. In
this a global network connects the local communication network to the outside world
and offers its services via a interface D. Global network could be ISDN, PSTN, PLMN eg
GSM or Packet Switched Public Data Network (PSPDN). The service offered by the
networks include transportation of data on one hand and the transition of address and
routing of data between the local networks on the other.
Local networks provides simple service to everything such as switching to call
forwarding, address translation etc. HDB – Home Data Base and VDB visitor data base
are also located at the local network.
The DECT core network consists of the fixed radio termination (FT) and the portable
Radio Termination PT and basically only provides multiplexing service.
Protocol Architecture:
DECT protocol reference architecture follows the OSI reference mode.
Following figures shows the layers covered by this standard.
9
Mobile Computing Unit 2
Physical Layer
The physical layer, medium access control, and data link control for both the
control place (C – Plane) and the user plane (U-Plane). Only for the C place, an
additional network layer has been specified so that the user data from layer two is
directly forwarded top the U plane. A management plane covers all lower layers of a
DECT system.
Physical layer comprises all functions for modulation / demodulation, incoming
signal detection,, sender / receiver synchronization, and collection of status
information for the management plane. On request from MAC layer, the physical layer
assigns a channel for data transmission.
Following diagram shows the TDMA frame structure used in DECT:
10
Mobile Computing Unit 2
Each frame has a duration of 10 ms and contains 12 slots for down link and 12 slots
for uplink. In basic connection mode. If a mobile receives data in slot n, it returns data
in n+ 12 slot. After leaving for sync bits and guard space, 388 bits are used for
network control (A field) and user data(B field).
With a data rate of 6.4 kbps, (64 bits per 10 ms) , the user data rate depends
on additional error correction mechanism. Simplex bearer provides a data rate of 32
kbps in unprotected mode while using 16 bit CRC checksum for data block of 64 bits in
the protected mode. This reduces the data rate to 25.6 kbps.
Medium Access Control Layer:
It is intended to establish, maintain and release channels for higher layers by
activating and deactivating physical channels. It multiplexes several logical channels
onto physical channels. Logical channel exists for signalling network control, user data
transmission, paging or sending broadcast messages. Additional services offered
include segmentation / re assembly of packets and error control / error correction.
Data Link Control Layer:
The purpose of the DLC is to create and maintain reliable connections between the
mobile and the base station. There are two services called C Plane (control
plane)and U plane (user plane).
C Plane:
It has Connectionless broadcast service for paging called Lb and point to point
protocol similar to LAPD (Link Access Procedure for D Channel) in ISDN but
adopted to the underlying MAC as LAPC +Lc
U plane:
In case of User plane, several services exists. Transparent unprotected service.
As forward error correction service, rate adaptation service, services for future
enhancement.
Network Layer:
11
Mobile Computing Unit 2
Network layer exist only in C plane. This layer provides services to
request, check, reserve control and release resources at the fixed station and the mobile
terminal
Mobility Management:
Mobility Management within the network layer is responsible for identity
management, authentication and management of the location data bases.
Call Control (CC):
Handles connection set up, release, and negotiation. Two message services,
connection oriented message service and connectionless message service transfers data
to and from the internetworking unit that connects the DECT system with the outside
world.
DECT
message
Time Division Multiple Access:
TDMA radio access, with its low radio interference characteristics, provides high
system capacity to handle up to 100'000 users per km² floor space in an office
environment.
Adaptive Differential Pulse Code Modulation:
ADPCM (Adaptive Differential Pulse Code Modulation) speech encoding ensures a
DECT cordless phone very high speech quality, comparable to wire line telephony.
SATELLITE SYSTEMS
12
Physical
Medium Access Control
Data Link control
Cal
l con
trol
Supp
lem
ent a
ry
Serv
ices
Con
nect
ionl
ess
Mes
sage
Ser
vice
Con
nect
ion
Ori
ente
d M
essa
ge S
ervi
ce
Mob
ilit
y M
anag
emen
t
Physical
Medium Access Control
Data Link control
Cal
l con
trol
Supp
lem
ent a
ry
Serv
ices
Con
nect
ionl
ess
Mes
sage
Ser
vice
Con
nect
ion
Ori
ente
d M
essa
ge S
ervi
ce
Mob
ilit
y M
anag
emen
t
Mobile Computing Unit 2
13
Mobile Computing Unit 2
14
Mobile Computing Unit 2
15
Mobile Computing Unit 2
16
Mobile Computing Unit 2
17
Mobile Computing Unit 2
BROADCAST SYSTEMS
18
Mobile Computing Unit 2
19
Mobile Computing Unit 2
20
Mobile Computing Unit 2
21
Mobile Computing Unit 2
22
Mobile Computing Unit 2
23
Mobile Computing Unit 2
24
Mobile Computing Unit 2
25
Mobile Computing Unit 2
Summary
In this unit, GSM is presented as the most successful second generation digital cellular
network. Although GSM was primarily designed for voice transmission, it showed the
evolution of the data oriented transfer via HSCSD and GPRS. This evolution also
includes the transition from a circuit switched network to a packet-switched system
that comes closer to the internet model. Other systems presented include DECT, the
digital standard for cordless phones and TETRA, a trunked radio system. DECT can be
used for wireless data transmission on a campus or indoors, but also for wireless local
loops. Also, an overview of the current and the future third generation systems were
discussed. The Broadcasting systems and their technologies were discussed in the later
part of the unit. DAB and DVB likely the successors of the traditional radio and
television, were presented.
Key Terms
GPRS-General Packet Radio Service
26
Mobile Computing Unit 2
DECT- Digital Enhanced Cordless Telecommunications
TETRA- Terrestrial Trunked Radio
DAB –Digital audio broadcasting
DVB –Digital video broadcasting
HSCSD -High Speed Circuit Switched Data
Multiple Choice Questions
1. ---------- introduced a packet-oriented service and higher data rates to GSM.
a) GPRS b)DECT c)TETRA d)UMTS
2. ----------replaces older analog cordless phone systems such as CT1 and CT1+.
a) GPRS b)DECT c)TETRA d)UMTS
3. ---------- use many different radio carriers but only assign a specific carrier to a certain user for a short period of time according to demand.
a) GPRS b)DECT c)TETRA d)UMTS
4. The ------------system does not only offer sound in a CD-like quality, it is also practically immune to interference and multi-path propagation effects.
a) DAB b)DVB c)TETRA d)UMTS
5. ----------- can be also used for high bandwidth, asymmetrical Internet access.a) DAB b)DVB c)TETRA d)UMTS
Question & Answers
Part A Questions
1. What is Network and Switching subsystem?The heart of the GSM is formed by the Network and Switching System (NSS). NSS consists of the following switches and databases: Mobile Services switching center(MSC) Home Location register (HLR) Visitor Location Register (VLR)
2. What is authentication centre?As the radio interface and mobile stations are particularly vulnerable a separate
AuC has been defined to protect user identity and data transmission. The AuC contains the algorithms for authentication as well as the keys for encryption and generates the values needed for user authentication in the HLR. The AuC may, in fact, be situated in a special protected part of the HLR.3. What is called burst and normal burst?
Data is transmitted in small portions called bursts, normal burst are used for data transmission inside a slot (user and signaling data).4. What are the basic groups of logical channels?
GSM specifies 2 basic groups of logical channels, Traffic channels
27
Mobile Computing Unit 2
Control channels5. Define traffic multiframe and control multiframe?
The periodic pattern of 26 slots occurs in all TDMA frames with a TCH. The combination of these frames is called traffic multiframe. TDMA frames containing data for the other logical channels are combined to a
control multiframe.6. What is OVSF?
Using orthogonal codes separates the different data streams of a sender UMTS uses so-called Orthogonal Variable Spreading factor codes (OVSF).
7. Specify the steps perform during the search for a cell after power on? Primary synchronization Secondary synchronization Identification of the scrambling code
8. Explain about transparent mode?The transparent mode transfer simply forwards MAC data without any further
processing. The system then has to rely on the FEC which is always used in the radio layer.9. What are the basic classes of handovers in UMTS?
UMTS has 2 basic classes of handovers, Hard handover Soft handover
10. Specify the security services offered by GSM.There are three security services offered by GSM.They are: Bearer Services. Tele Services. Supplementary Services.
11. What is the frequency range of uplink and downlink in GSM network? The frequency range of uplink in GSM network is 890-960 MHz. The frequency range of downlink in GSM network is 935-960 MHz.
12. What are the two basic groups of logical channels in GSM?The two basics groups of logical channels in GSM are: Traffic channels (TCH). Control Channels (CCH).
13. What are the control channel groups in GSM?The control channel groups in GSM are:
Broadcast control channel (BCCH). Common control channel (CCCH). Dedicated control channel (DCCH).
14. List out the numbers needed to locate an MS and to address the MS.The numbers needed to locate an MS and to address the MS are: Mobile station international ISDN number (MSISDN). International mobile subscriber identity (IMSI). Temporary mobile subscriber identity (TMSI). Mobile station roaming number (MSRN).
15. What are the four possible handover scenarios in GSM?The four possible handover scenarios in GSM are: Intra-cell handover. Inter-cell, intra-BSC handover.
28
Mobile Computing Unit 2
Inter-BSC, intra-MSC handover. Inter MSC handover.
16. What are the security services offered by GSM?The security services offered by GSM are: Access control and authentication. Confidentiality. Anonymity.
17. What is meant by GGSN?GGSN is Gateway GPRS Support Node. It is the inter-working unit between the
GPRS network and external packet data networks. The GGSN is connected to external networks via the Gi interface and transfers packets to the SGSN via an IP-based GPRS backbone network.18. What is meant by SGSN?
SGSN is Serving GPRS Support Node. It supports the MS via the Gb interface. The SGSN is connected to a BSC via frame relay.19. What is meant by BSSGP?
BSSGP is Base Station Subsystem GPRS Protocol. It is used to convey routing and QoS-related information between the BSS and SGSN.BSSGP does not perform error correction and works on top of a frame relay network.20. Define the protocol architecture of DECT.
The protocol architecture of DECT consists of three layers. Theyare: Physical Layer. Medium Access Layer. Data Link Control Layer. Network Layer.The first three layers are common for both Control Plane (C-Plane) and User Plane
(U-Plane). The network layer has been specified only for U-Plane, so that user data from layer two is directly forwarded to the U-Plane.21. Specify the standards offered by TETRA.
TETRA offers two standards. They are: Voice+Data (V+D). Packet Data Optimized (PDO).
22. How many ITU standardized groups of 3G radio access technologies are there in IMT-2000?There are five groups. They are:
IMT-DS IMT-TC IMT-MC IMT-SC IMT-FT
23. What are the steps perform during the search for a cell after power on?The steps perform during the search for a cell after power on is:
Primary Synchronization. Secondary Synchronization. Identification of the scrambling code.
24. What are the two basic classes of handover?The two basic classes of handover are: Hard Handover. Soft Handover.
29
Mobile Computing Unit 2
25. What are the two basic transport mechanisms used by DAB?The two basic transport mechanisms used by DAB are: Main Service Channel (MSC). Fast Information Channel (FIC).
26. What are the two transport modes defined for MSC?The two transport modes defined for MSC are:
Stream Mode Packet Mode.
27. Define the terms:i. Earth Station.ii. Uplink.iii. Downlink.
Earth Station:-The antenna systems on or near the earth are referred to as Earth Station.
Uplink:-A transmission from an earth station to the satellite is referred to as Uplink.
Downlink:-A transmission from the satellite to the earth station is referred to as Downlink.
28. Define Elevation Angle.The Elevation angle is the angle from the horizontal to the point on the center of
the main beam of the antenna when the antenna is pointed directlyat the satellite.29. What are the factors limited the number of sub channels provided within the satellite channel?
There are three factors limited the number of sub channels providedwithin the satellite channel. They are:-
Thermal Noise. Intermodulation Noise. Crosstalk.
Part B Questions
1. Explain GSM architecture? Mobile services Bearer services Tele services Supplementary services System architecture Radio subsystem Network and switching subsystem Operation subsystem
2. Explain Protocol architecture?Protocol architecture Physical Layer Medium access control Layer Data link control layer
3. Explain briefly about TETRA?The 2 standards are,Voice DataPacket data optimized (PDO)
30
Mobile Computing Unit 2
The system architecture of TETRA is similar to GSM.TETRA offers 2 channels similar to GSM as,
Traffic channels control channels
4.Write brief about UMTS and IMT-2000? UMTS releases and standardization UMTS system architecture UMTS radio interface
5.Explain about UTRAN? Radio network controller User equipment Core network Hand over
6. Explain Satellite networks in detail. Basic concepts Parameters and configurations Capacity Allocation-FDMA,TDMA FAMA DAMA
7. Write short notes on DAB. MSC FIC DAB Frame Structure Components of DAB sender Multimedia Object Transfer Protocol
8. Write short notes on DVB. DVB data broadcasting DVB for high-speed internet access
9. Explain DECT. DECT definition System architecture Protocol architecture
10. Explain about GSM
31
Mobile Computing Unit 2
Review Questions and Exercises
32
Mobile Computing Unit 2
33
Mobile Computing Unit 2
References
http://cst.mi.fu-berlin.de/resources/mobkom/material/English/PDF-Handout/C01-
Introduction.pdf
http://cst.mi.fu-berlin.de/resources/mobkom/material/English/PDF-Handout/C02-
Wireless_Transmission.pdf
http://cst.mi.fu-berlin.de/resources/mobkom/material/English/PDF-Handout/C03-Media_Access.pdf
34