model ni8 al-xx70-b rs-x70 20210302 available …
TRANSCRIPT
MODELOL-HRN-RS-NI8
GUIDE IDNI8_AL-XX70-B_RS-X70_20220131
AVAILABLE ACCESSORIESOL-HRN-RS-PWR (Adapt to any brand remote start)
INSTALL GUIDE
VEHICLE COMPATIBILITY
DISCLAIMER: The manufacturer of this product nor its affiliates accept any responsibility for any electrical damage to the vehicle or any other connected systems as a result of improper installation of this product. All wiring connections & vehicle compatibility must be verified by a professionally qualified technician prior to installation.!
For AL-XX70-B installations see pages 2-13For RS-X70 installations see pages 14-25
For OL-MDB-ALL Stand-Alone installations see pages 26-36
Infiniti QX50 Push-to-Start Automatic 2019 - 2020 DL-NI8 RS-NI8 4
Nissan Altima Push-to-Start Sedan Automatic 2019 - 2021 DL-NI8 RS-NI8 2
Nissan Qashqai Push-to-Start 4 Cyl. Automatic 2017 - 2020 DL-NI8 RS-NI8 2
Nissan Qashqai Std. Key 4 Cyl. Automatic 2017 - 2018 DL-NI9 RS-NI9 2
Nissan Qashqai Std. Key 4 Cyl. Automatic 2019- 2020 DL-NI9 RS-NI9 3
Nissan Rogue Push-to-Start 4 Cyl. Automatic 2014 - 2016 DL-NI8 RS-NI8 1
Nissan Rogue Push-to-Start 4 Cyl. Automatic 2017 - 2020 DL-NI8 RS-NI8 2
Nissan Rogue Std. Key 4 Cyl. Automatic 2014 - 2016 DL-NI9 RS-NI9 1
Nissan Rogue Std. Key 4 Cyl. Automatic 2017 - 2017 DL-NI9 RS-NI9 2
Nissan Rogue Std. Key 4 Cyl. Automatic 2018 - 2020 DL-NI9 RS-NI9 3
Nissan Rogue Sport Push-to-Start 4 Cyl. Automatic 2017 - 2020 DL-NI8 RS-NI8 2
Nissan Rogue Sport Std. Key 4 Cyl. Automatic 2017 - 2018 DL-NI9 RS-NI9 2
Nissan Rogue Sport Std. Key 4 Cyl. Automatic 2019 - 2020 DL-NI9 RS-NI9 3
Make Model Trim YearsFirmware
DiagramXX70 or X70 Stand-Alone
For AL-XX70-B & RS-X70 installations configure Installer Feature #9 to LOCK AFTER RS OFF to control
RAP/Autolight Shutdown. See system installtion guide for programming instructions
INSTALL GUIDEGUIDE ID: NI8_AL-XX70-B_RS-X70_20220131 Page 2 of 36
MODEL: OL-HRN-RS-NI8
INSTALLATION STEPS:1) Go to OmegaWeblink.com or use WebLink Mobile to fl ash the OL-BLADE-AL64 with the fi rmware matching the vehicle.
NOTE: If OEM remote is being used to activate the remote start be sure to enable “Factory keyless RS sequence” as “Lock + Lock + Lock” OR “Lock + Unlock + Lock”2) While at OmegaWeblink.com, make sure the AL-XX70-B is updated to v1.5 FW or higher.3) Make all the connections shown in the diagram on the following pages.4) Connect any optional hardware as needed.5) Program the OL-BLADE-AL64 to the vehicle (see “BLADE Programming” on the following pages).6) Perform Vehicle Learn to confi gure the remote start to match the vehicle (see “AL-XX70-B Programming/Vehicle Learn” on the following pages).
NOTE: If Vehicle Learn is not performed remote start operation could fail.7) Test the system for all desired functions.
NOTE: Any features NOT supported by the interface module must be hard wired from the remote start to the vehicle. Refer to the remote start install guide and vehicle wiring info at www.wiresheet.com (only available for authorized dealers) for instructions.
AL-XX70-B Layout
F WHITE 4 PIN PLUG-IN SENSOR PORTS (harness included w/ optional sensors)
G TEMPERATURE SENSOR - DO NOT COVER(For high/low temp auto start and for automatic low temp crank extender)
H BLADE CARTRIDGE PORT - For OL-BLADE-AL64 or OL-BLADE-TB
I GREEN & BLACK DATA PORTS - For Telematics / Data Sensor (Shock, Tilt, etc) / Vehicle Interface Module. (DBI & iDatalink protocols supported on both ports - see ‘Vehicle Learn’ or installer feature #12)
J BLADE HARNESS PORT - Use harness from BLADE or an ‘OL-HRN-RS’ T-Harness.
L BACKUP BATTERY PORT - Uses standard 9v battery with bracket & plug. Featuring PowerMaze technology - only supports security critical functions!
K ANTENNA / STATUS LIGHT / VALET PORT - Supports compatible plug-in antennas or push-button status light (P/N: AU-LED-PB2)
A WHITE 6 PIN HIGH CURRENT POWER HARNESS (P/N: H-RS6E*)
B WHITE 18 PIN MAIN INPUT/OUTPUT HARNESS (P/N: H-RS18A)
C RED 4 PIN DOOR LOCK/UNLOCK HARNESS (P/N: DLP-N4)
D RED 3 PIN REMOTE START HARNESS (P/N: RS-OUTPUT)
E WHITE 4 PIN AUXILIARY HARNESS (P/N: H-RS4)
F
C D E I J K
G
L
H
AB
AL-XX70-B Installation Steps
INSTALL GUIDEGUIDE ID: NI8_AL-XX70-B_RS-X70_20220131 Page 3 of 36
MODEL: OL-HRN-RS-NI8Wire Location Chart Diagram #1
Nissan Rogue Push-to-Start 4 Cyl. Automatic 2014 - 2016
Body Control Module - - - - - Under Driver Side Dash
Horn WHITE 100 35 TAN (-) Driver Kick Panel
Lift Gate GREEN 8 6 LT.GREEN (-) At Switch On Lower Dash
Nissan Rogue Std. Key 4 Cyl. Automatic 2014 - 2016
Body Control Module - - - - - Under Driver Side Dash
Horn WHITE 100 35 TAN (-) Driver Kick Panel
Lift Gate GREEN 8 6 LT.GREEN (-) At Switch On Lower Dash
Make Model Trim Year Item Connector Color
Connector Pins Pin # Wire Color Polarity Location
INSTALL GUIDEGUIDE ID: NI8_AL-XX70-B_RS-X70_20220131 Page 4 of 36
MODEL: OL-HRN-RS-NI8
J
E
PIN COLOR1 PINK2 WHITE/BLUE3 LT. GREEN/RED4 LT. GREEN/BLACK
1
4
N/CN/CN/CN/C
DPIN COLOR
1 BLUE2 RED3 GREEN3
1
BLUE
N/CN/CN/C
DPIN COLOR
1 BLUE2 RED3 GREEN3
1
RED
N/CN/CN/C
C
B
PIN COLOR1 VIOLET/WHITE2 BLACK/RED3 GREEN/VIOLET4 WHITE/BLACK5 BROWN/RED6 WHITE/RED7 WHITE8 BROWN/BLACK9 VIOLET/BLACK
10 GREEN11 VIOLET12 RED/WHITE13 ORANGE14 BLACK15 BLACK/WHITE16 GRAY17 BROWN18 BLUE/BLACK
110
918
N/CN/CN/C
N/CN/CN/CN/C
N/CN/C
N/C
N/C
N/C
A
AL-XX70-B Diagram #1
Door Lock Option A
Door Lock Option B
CAN Option A
CAN Option B
BLUE/BLACK - OEM Horn (-) OutputOPTIONAL
BROWN - Siren (+) OutputOPTIONAL
BLACK -Chassis Ground
Optional Siren
RED
OEM Horn
GRAY - Connect to supplied hood pin IF no OEM hood pin is present
A
PINK - Not Used
CB
BCM HARNESS (BLACK CONN)
DE
BCM HARNESS (GRAY CONN)
HJ
BCM HARNESS (BLACK CONN)
OL-HRN-RS-NI8(A)
OL-HRN-RS-NI8(D)DL-NI8/9
DO NOT CONNECT
BLACK - Ground
FG
Body Control Module
DO NOT CONNECT
DO NOT CONNECT
K L
VEHICLE’S OBDII
CONNECTOR
RED/WHITE - Trunk Release (-) OutputPower Liftgate
OPTIONAL
INSTALL GUIDEGUIDE ID: NI8_AL-XX70-B_RS-X70_20220131 Page 5 of 36
MODEL: OL-HRN-RS-NI8Wire Location Chart Diagram #2
Nissan Altima Push-to-Start Sedan Automatic 2019 - 2021
Body Control Module - - - - - Under Driver Side Dash
Horn BLACK 16 10 VIOLET (-) Horn Switch On Column
Trunk Release GRAY 4 2 BROWN (-) At Liftgate Switch Lower Dash Panel
Nissan Qashqai Push-to-Start 4 Cyl. Automatic 2017 - 2020
Body Control Module - - - - - Under Driver Side Dash
Horn WHITE 14 14 WHITE (-) At Horn Switch On Column
Lift Gate GREEN 8 6 LT.GREEN (-) At Liftgate Switch Lower Dash Panel
Nissan Qashqai Std. Key 4 Cyl. Automatic 2017 - 2018
Body Control Module - - - - - Under Driver Side Dash
Horn WHITE 14 14 WHITE (-) At Horn Switch On Column
Lift Gate GREEN 8 6 LT.GREEN (-) At Liftgate Switch Lower Dash Panel
Nissan Rogue Push-to-Start 4 Cyl. Automatic 2017 - 2020
Body Control Module - - - - - Under Driver Side Dash
Horn WHITE 100 35 TAN (-) Driver Kick Panel
Lift Gate GREEN 8 6 LT.GREEN (-) At Liftgate Switch Lower Dash Panel
Nissan Rogue Std. Key 4 Cyl. Automatic 2017 - 2017
Body Control Module - - - - - Under Driver Side Dash
Horn WHITE 100 35 TAN (-) Driver Kick Panel
Lift Gate GREEN 8 6 LT.GREEN (-) At Liftgate Switch Lower Dash Panel
Nissan Rogue Sport Push-to-Start 4 Cyl. Automatic 2017 - 2020
Body Control Module - - - - - Under Driver Side Dash
Horn WHITE 100 79 PINK (-) Driver Kick Panel
Lift Gate GREEN 8 6 LT.GREEN (-) At Liftgate Switch Lower Dash Panel
Nissan Rogue Sport Std. Key 4 Cyl. Automatic 2017 - 2018
Body Control Module - - - - - Under Driver Side Dash
Horn WHITE 100 79 PINK (-) Driver Kick Panel
Lift Gate GREEN 8 6 LT. GREEN (-) At Liftgate Switch Lower Dash Panel
Make Model Trim Year Item Connector Color
Connector Pins Pin # Wire Color Polarity Location
INSTALL GUIDEGUIDE ID: NI8_AL-XX70-B_RS-X70_20220131 Page 6 of 36
MODEL: OL-HRN-RS-NI8
J
E
PIN COLOR1 PINK2 WHITE/BLUE3 LT. GREEN/RED4 LT. GREEN/BLACK
1
4
N/CN/CN/CN/C
DPIN COLOR
1 BLUE2 RED3 GREEN3
1
BLUE
N/CN/CN/C
DPIN COLOR
1 BLUE2 RED3 GREEN3
1
RED
N/CN/CN/C
C
B
PIN COLOR1 VIOLET/WHITE2 BLACK/RED3 GREEN/VIOLET4 WHITE/BLACK5 BROWN/RED6 WHITE/RED7 WHITE8 BROWN/BLACK9 VIOLET/BLACK
10 GREEN11 VIOLET12 RED/WHITE13 ORANGE14 BLACK15 BLACK/WHITE16 GRAY17 BROWN18 BLUE/BLACK
110
918
N/CN/CN/C
N/CN/CN/CN/C
N/CN/C
N/C
N/C
N/C
A
AL-XX70-B Diagram #2
Door Lock Option A
Door Lock Option B
CAN Option B
CAN Option A
BROWN - Siren (+) OutputOPTIONAL
BLACK -Chassis Ground
Optional Siren
RED
GRAY - Connect to supplied hood pin IF no OEM hood pin is present
A
PINK - Not Used
CB
BCM HARNESS (BLACK CONN)
BCM HARNESS (GRAY CONN)
BCM HARNESS (BLACK CONN)
BLACK - Ground
BCM HARNESS (GREEN CONN)
Body Control Module
VEHICLE’S OBDII
CONNECTOR
OL-HRN-RS-NI8(A)
OL-HRN-RS-NI8(D)DL-NI8/9
BLUE/BLACK - OEM Horn (-) OutputOPTIONAL
OEM Horn
RED/WHITE - Trunk Release (-) Output
Power Liftgate/Trunk Release
OPTIONAL
DO NOT CONNECT
DE
HJ
FGK L
INSTALL GUIDEGUIDE ID: NI8_AL-XX70-B_RS-X70_20220131 Page 7 of 36
MODEL: OL-HRN-RS-NI8Wire Location Chart Diagram #3
Nissan Qashqai Std. Key 4 Cyl. Automatic 2019 - 2020
Body Control Module - - - - - Under Driver Side Dash
Horn WHITE 14 14 WHITE (-) At Horn Switch On Column
Lift Gate GREEN 8 6 LT.GREEN (-) At Liftgate Switch Lower Dash Panel
Nissan Rogue Std. Key 4 Cyl. Automatic 2018 - 2020
Body Control Module - - - - - Under Driver Side Dash
Horn WHITE 100 35 TAN (-) Driver Kick Panel
Lift Gate GREEN 8 6 LT.GREEN (-) At Liftgate Switch Lower Dash Panel
Nissan Rogue Sport Std. Key 4 Cyl. Automatic 2019 - 2020
Body Control Module - - - - - Under Driver Side Dash
Horn WHITE 100 79 PINK (-) Driver Kick Panel
Lift Gate GREEN 8 6 LT.GREEN (-) At Liftgate Switch Lower Dash Panel
Make Model Trim Year Item Connector Color
Connector Pins Pin # Wire Color Polarity Location
INSTALL GUIDEGUIDE ID: NI8_AL-XX70-B_RS-X70_20220131 Page 8 of 36
MODEL: OL-HRN-RS-NI8AL-XX70-B Diagram #3
J
E
PIN COLOR1 PINK2 WHITE/BLUE3 LT. GREEN/RED4 LT. GREEN/BLACK
1
4
N/CN/CN/CN/C
DPIN COLOR
1 BLUE2 RED3 GREEN3
1
BLUE
N/CN/CN/C
DPIN COLOR
1 BLUE2 RED3 GREEN3
1
RED
N/CN/CN/C
C
B
PIN COLOR1 VIOLET/WHITE2 BLACK/RED3 GREEN/VIOLET4 WHITE/BLACK5 BROWN/RED6 WHITE/RED7 WHITE8 BROWN/BLACK9 VIOLET/BLACK
10 GREEN11 VIOLET12 RED/WHITE13 ORANGE14 BLACK15 BLACK/WHITE16 GRAY17 BROWN18 BLUE/BLACK
110
918
N/CN/CN/C
N/CN/CN/CN/C
N/CN/C
N/C
N/C
N/C
A
Door Lock Option A
Door Lock OptionB
CAN Option B
CAN Option A
CONNECT
BROWN - Siren (+) OutputOPTIONAL
BLACK -Chassis Ground
Optional Siren
RED
GRAY - Connect to supplied hood pin IF no OEM hood pin is present
A
PINK - Not Used
CB
BCM HARNESS (BLACK CONN)
BCM HARNESS (GRAY CONN)
BCM HARNESS (BLACK CONN)
BLACK - Ground
BCM HARNESS (GREEN CONN)
Body Control Module
VEHICLE’S OBDII
CONNECTOR
OL-HRN-RS-NI8(A)
OL-HRN-RS-NI8(D)DL-NI8/9
BLUE/BLACK - OEM Horn (-) OutputOPTIONAL
OEM Horn
RED/WHITE - Trunk Release (-) OutputPower Liftgate
OPTIONAL
DE
HJ
FGK L
INSTALL GUIDEGUIDE ID: NI8_AL-XX70-B_RS-X70_20220131 Page 9 of 36
MODEL: OL-HRN-RS-NI8Wire Location Chart Diagram #4
Infiniti QX50 Push-to-Start Automatic 2019 - 2020
Body Control Module - - - - - Under Driver Side Dash
Horn WHITE 100 18 GRAY (-) Driver Kick Panel
Lift Gate WHITE 16 4 WHITE (-) At Liftgate Switch Lower Dash Panel
Make Model Trim Year Item Connector Color
Connector Pins Pin # Wire Color Polarity Location
INSTALL GUIDEGUIDE ID: NI8_AL-XX70-B_RS-X70_20220131 Page 10 of 36
MODEL: OL-HRN-RS-NI8AL-XX70-B Diagram #4
J
E
PIN COLOR1 PINK2 WHITE/BLUE3 LT. GREEN/RED4 LT. GREEN/BLACK
1
4
N/CN/CN/CN/C
DPIN COLOR
1 BLUE2 RED3 GREEN3
1
BLUE
N/CN/CN/C
DPIN COLOR
1 BLUE2 RED3 GREEN3
1
RED
N/CN/CN/C
C
B
PIN COLOR1 VIOLET/WHITE2 BLACK/RED3 GREEN/VIOLET4 WHITE/BLACK5 BROWN/RED6 WHITE/RED7 WHITE8 BROWN/BLACK9 VIOLET/BLACK
10 GREEN11 VIOLET12 RED/WHITE13 ORANGE14 BLACK15 BLACK/WHITE16 GRAY17 BROWN18 BLUE/BLACK
110
918
N/CN/CN/C
N/CN/CN/CN/C
N/CN/C
N/C
N/C
N/C
A
Door Lock Option B
Door Lock Option A
CAN Option B
CAN Option A
BROWN - Siren (+) OutputOPTIONAL
BLACK -Chassis Ground
Optional Siren
RED
GRAY - Connect to supplied hood pin IF no OEM hood pin is present
A
PINK - Not Used
CB
BCM HARNESS (BLACK CONN)
BCM HARNESS (GRAY CONN)
BCM HARNESS (BLACK CONN)
BLACK - Ground
BCM HARNESS (GREEN CONN)
Body Control Module
VEHICLE’S OBDII
CONNECTOR
OL-HRN-RS-NI8(A)
OL-HRN-RS-NI8(D)DL-NI8/9
BLUE/BLACK - OEM Horn (-) OutputOPTIONAL
OEM Horn
RED/WHITE - Trunk Release (-) OutputTrunk Release
OPTIONAL
CONNECT
DE
HJ
FGK L
INSTALL GUIDEGUIDE ID: NI8_AL-XX70-B_RS-X70_20220131 Page 11 of 36
MODEL: OL-HRN-RS-NI8
YELLOW - Alarm notifi cation input (+/-)
AL-XX70-B Optional Accessories
Antenna Cable
Push-Button LED Cable
K Antenna/LED Cable OR
Mod
el: L
INKR
-LT
ww
w.o
meg
alin
kr.c
om
I
I OL-ADAPTOR-B2G DATA CABLE
DATA CABLE
OR
F SENSOR CABLE
BLACK
GREEN
Any Add-onSensor
AL-XX70-B MUST have V1.4 or newer fi rmware for Linkr-LT compatibility.
INSTALL GUIDEGUIDE ID: NI8_AL-XX70-B_RS-X70_20220131 Page 12 of 36
MODEL: OL-HRN-RS-NI8Blade Installation
Slide Blade into unit. Notice programming button under LED.
Blade Programming
Blade Programming (cont.)
OR
Wait, the LED will turn OFF.
Turn the ignition to the ON position.1
Turn the ignition to the OFF position.
4
Wait, the LED will turn solid RED, then solid BLUE for 1 second, then solid RED.
2
3
ENGINESTARTSTOP
ENGINESTARTTTSTOP
OFF ACC STARTON
ENGINESTARTSTOP
ENGINESTARTTTSTOP
OFF ACC STARTON
5
6
Turn the ignition to the ON position.
ENGINESTARTSTOP
ENGINESTARTTTSTOP
OFF ACC STARTON
If LED flashes BLUE rapidly proceed with step 7. If LED turns solid BLUE for 2 seconds proceed to step 13.
WARNING:Disconnect power lastDisconnect remote start from vehicle.
WARNING: Do not press Blade programming button. Connect power first.Connect all other remote start connectors
10
Connect remote start to computer and proceed with extended programming.9
8
Turn the ignition to the OFF position.7
Proceed to AL-XX70-B Programming/Vehicle Learn.
Turn the ignition to the ON position.11
Turn the ignition to the OFF position.
14
Wait, the LED will turn solid RED, then solid BLUE for 1 second, then solid RED.
12
13
ENGINESTARTSTOP
ENGINESTARTTTSTOP
OFF ACC STARTON
ENGINESTARTSTOP
ENGINESTARTTTSTOP
OFF ACC STARTON
ENGINESTARTSTOP
ENGINESTARTTTSTOP
OFF ACC STARTON
INSTALL GUIDEGUIDE ID: NI8_AL-XX70-B_RS-X70_20220131 Page 13 of 36
MODEL: OL-HRN-RS-NI8
AL-XX70-B Programming/Vehicle Learn V1.6 (see installation guide for older versions)
Before You Begin:- Make sure all wires/harnesses are connected.- Program the BLADE to the vehicle per the instructions on the previous pages.- Connect any additional accessories/modules to the data ports.- MANUAL TRANSMISSION VEHICLES ONLY: Set the parking brake. The BLACK/WHITE wire must be connected to the parking brake wire.
Within 5 seconds of step 1 press the Valet button 3x or send remote start command (by remote, Linkr, activa-tion input wire etc.).
- The system will chirp & fl ash lights to indicate crankdelay (Default: 1 chirp/fl ash = 1.5 sec)
- Press valet button to change crank delay- Chirps: 1=1.5 sec, 2=15 sec, 3=20 sec, 4=30 sec
2
Programming complete.8
MANUAL TRANSMISSIONS: Release the parking brake.
AUTOMATIC TRANSMISSIONS: Turn the ignition key OFF.
- The system will chirp & fl ash the lights equal the #of IGN/ACC/START circuits detected (Max: 4).
MANUAL - Proceed to step 5.AUTOMATIC - Skip to step 6.
4
ENGINESTARTSTOP
ENGINESTARTTTSTOP
OFF ACC STARTON
ENGINESTARTSTOP
ENGINESTARTTTSTOP
OFF ACC STARTON Turn ignition to ON position (do not start).1
ENGINESTARTSTOP
ENGINESTARTTTSTOP
OFF ACC STARTON Start the engine with the key and let the engine reach normal idle.
3
TO SAVE SETTINGS/FINISH VEHICLE LEARN: Press the BRAKE pedal (will shut down RS).
- This disables VEHICLE LEARN (to enable again, programinstaller feature #2 (bank 10) to “Enabled”.
TO CANCEL/START OVER: Press the valet button once.
7
5 MANUAL TRANSMISSIONS: Set the parking brake again to enter Manual Transmission Reservation Mode option selection. (installer feature #11)
- The system will chirp & fl ash the light to indicate currentsetting (default: 2 - Off)
- Set and Release the parking brake to scrool through settingoptions.
- Chirp confi rmation: 1 = ON - Shutdown w/ lock, 2 = OFF,3 = ON - Shutdown w/ door close, 4 = ON - Shutdown 10sec. after door close
- Before turning the key OFF, perform the MT reservationsequence (see operation guide) and exit the vehicle.
6
TroubleShooting
- See system installation guide for remote start diagnostics and troubleshooting.- See OmegaLink module/fi rmware guide at www.wiresheet.com for interface module diagnostics and troubleshooting.
OR
Activate remote start (within 60 sec. of Step 4 or 5). Wait until engine is running and LED fl ashes slowly (10-45 seconds after engine cranks & runs).Push-to-Start vehicles: Ensure the OEM fob is at least 20 ft. away to allow remote start.
- The system will detect data protocols, select the bestavailable engine running detection method, and, learn anyavaialble tach input (data or analog).
3x
2x
2x
INSTALL GUIDEGUIDE ID: NI8_AL-XX70-B_RS-X70_20220131 Page 14 of 36
MODEL: OL-HRN-RS-NI8
C D
AB
GFERS-X70 Layout
E TEMPERATURE SENSOR - DO NOT COVER(For high/low temp auto start and for automatic low temp crank extender)
F ANTENNA / STATUS LIGHT / VALET PORT - Supports compatible plug-in antennas or push-button status light (P/N: AU-LED-PB2)
G GREEN & BLACK DATA PORTS - For Telematics / Data Sensor (Shock, Tilt, etc) / Vehicle Interface Module. (DBI & iDatalink protocols supported on both ports - see ‘Vehicle Learn’ or installer feature #12)
A WHITE 6 PIN HIGH CURRENT POWER HARNESS (P/N: H-RS6E*)
B WHITE 14 PIN MAIN INPUT/OUTPUT HARNESS (P/N: H-RS14A)
C RED 3 PIN DOOR LOCK/UNLOCK HARNESS (P/N: DLP-N3)
D RED 3 PIN REMOTE START HARNESS (P/N: RS-OUTPUT)
RS-X70 Installation Steps
INSTALLATION STEPS:1) Go to www.OmegaWeblink.com or use WebLink Mobile to fl ash the bypass module with the fi rmware matching the vehicle.
NOTE: iDatalink 2-way protocol is recommended for full functionality.NOTE: If OEM remote is being used to activate the remote start be sure “Factory keyless RS sequence” is set to “Lock + Lock + Lock” OR “Lock + Unlock + Lock”
2) Make all the connections shown in the diagram on the following pages.3) Connect any optional hardware as needed.4) Select Data Mode and program the bypass module to the vehicle (see module programming instructions).5) Perform Vehicle Learn to confi gure the remote start to match the vehicle.
NOTE: If Vehicle Learn is not performed remote start operation could fail.6) Test the system for all desired functions.
NOTE: Any features NOT supported by the interface module must be hard wired from the remote start to the vehicle. Refer to the remote start install guide and vehicle wiring info at www.wiresheet.com (only available for authorized dealers) for instructions.
INSTALL GUIDEGUIDE ID: NI8_AL-XX70-B_RS-X70_20220131 Page 15 of 36
MODEL: OL-HRN-RS-NI8Wire Location Chart Diagram #1
Nissan Rogue Push-to-Start 4 Cyl. Automatic 2014 - 2016
Body Control Module - - - - - Under Driver Side Dash
Horn WHITE 100 35 TAN (-) Driver Kick Panel
Lift Gate GREEN 8 6 LT.GREEN (-) At Switch On Lower Dash
Nissan Rogue Std. Key 4 Cyl. Automatic 2014 - 2016
Body Control Module - - - - - Under Driver Side Dash
Horn WHITE 100 35 TAN (-) Driver Kick Panel
Lift Gate GREEN 8 6 LT.GREEN (-) At Switch On Lower Dash
Make Model Trim Year Item Connector Color
Connector Pins Pin # Wire Color Polarity Location
INSTALL GUIDEGUIDE ID: NI8_AL-XX70-B_RS-X70_20220131 Page 16 of 36
MODEL: OL-HRN-RS-NI8
DATA CABLE
RS-X70 Diagram #1
G
DPIN COLOR
1 BLUE2 RED3 GREEN3
1
N/CN/CN/C
C
B
PIN COLOR1 ORANGE2 WHITE/BLACK3 RED/WHITE4 LT. GREEN/BLACK5 GRAY6 VIOLET/WHITE7 BLACK/WHITE8 WHITE/BLUE9 YELLOW
10 LT. GREEN/RED11 BLACK12 BROWN13 BROWN/RED14 WHITE
18
714
N/C
N/C
N/CN/CN/CN/CN/C
N/CN/C
N/C
A
OL-H
RN-R
S-NI
8(B)
Connect PINK wires when using OL-HRN-RS-NI8(B) harness
BROWN - OEM Horn (-) Output
Door Lock Option A
Door Lock Option B
CAN Option A
CAN Option B
OPTIONALOEM Horn
GRAY - Connect to supplied hood pin IF no OEM hood pin is present
A
CB
BCM HARNESS (BLACK CONN)
BCM HARNESS (GRAY CONN)
BCM HARNESS (BLACK CONN)
OL-HRN-RS-NI8(A)
OL-HRN-RS-NI8(D)DL-NI8/9
DO NOT CONNECT
BLACK - Ground
Body Control Module
DO NOT CONNECT
DO NOT CONNECT
VEHICLE’S OBDII
CONNECTOR
RED/WHITE - Trunk Release (-) OutputPower Liftgate
OPTIONAL
DE
HJ
FGK L
INSTALL GUIDEGUIDE ID: NI8_AL-XX70-B_RS-X70_20220131 Page 17 of 36
MODEL: OL-HRN-RS-NI8Wire Location Chart Diagram #2
Nissan Altima Push-to-Start Sedan Automatic 2019 - 2021
Body Control Module - - - - - Under Driver Side Dash
Horn BLACK 16 10 VIOLET (-) Horn Switch On Column
Trunk Release GRAY 4 2 BROWN (-) At Liftgate Switch Lower Dash Panel
Nissan Qashqai Push-to-Start 4 Cyl. Automatic 2017 - 2020
Body Control Module - - - - - Under Driver Side Dash
Horn WHITE 14 14 WHITE (-) At Horn Switch On Column
Lift Gate GREEN 8 6 LT.GREEN (-) At Liftgate Switch Lower Dash Panel
Nissan Qashqai Std. Key 4 Cyl. Automatic 2017 - 2018
Body Control Module - - - - - Under Driver Side Dash
Horn WHITE 14 14 WHITE (-) At Horn Switch On Column
Lift Gate GREEN 8 6 LT.GREEN (-) At Liftgate Switch Lower Dash Panel
Nissan Rogue Push-to-Start 4 Cyl. Automatic 2017 - 2020
Body Control Module - - - - - Under Driver Side Dash
Horn WHITE 100 35 TAN (-) Driver Kick Panel
Lift Gate GREEN 8 6 LT.GREEN (-) At Liftgate Switch Lower Dash Panel
Nissan Rogue Std. Key 4 Cyl. Automatic 2017 - 2017
Body Control Module - - - - - Under Driver Side Dash
Horn WHITE 100 35 TAN (-) Driver Kick Panel
Lift Gate GREEN 8 6 LT.GREEN (-) At Liftgate Switch Lower Dash Panel
Nissan Rogue Sport Push-to-Start 4 Cyl. Automatic 2017 - 2020
Body Control Module - - - - - Under Driver Side Dash
Horn WHITE 100 79 PINK (-) Driver Kick Panel
Lift Gate GREEN 8 6 LT.GREEN (-) At Liftgate Switch Lower Dash Panel
Nissan Rogue Sport Std. Key 4 Cyl. Automatic 2017 - 2018
Body Control Module - - - - - Under Driver Side Dash
Horn WHITE 100 79 PINK (-) Driver Kick Panel
Lift Gate GREEN 8 6 LT. GREEN (-) At Liftgate Switch Lower Dash Panel
Make Model Trim Year Item Connector Color
Connector Pins Pin # Wire Color Polarity Location
INSTALL GUIDEGUIDE ID: NI8_AL-XX70-B_RS-X70_20220131 Page 18 of 36
MODEL: OL-HRN-RS-NI8
DATA CABLE
RS-X70 Diagram #2
G
DPIN COLOR
1 BLUE2 RED3 GREEN3
1
N/CN/CN/C
C
B
PIN COLOR1 ORANGE2 WHITE/BLACK3 RED/WHITE4 LT. GREEN/BLACK5 GRAY6 VIOLET/WHITE7 BLACK/WHITE8 WHITE/BLUE9 YELLOW
10 LT. GREEN/RED11 BLACK12 BROWN13 BROWN/RED14 WHITE
18
714
N/C
N/C
N/CN/CN/CN/CN/C
N/CN/C
N/C
A
Door Lock Option A
Door Lock Option B
CAN Option B
CAN Option A
OL-H
RN-R
S-NI
8(B)
Connect PINK wires when using OL-HRN-RS-NI8(B) harness
BROWN - OEM Horn (-) OutputOPTIONAL
OEM Horn
GRAY - Connect to supplied hood pin IF no OEM hood pin is present
A
OL-HRN-RS-NI8(A)
OL-HRN-RS-NI8(D)DL-NI8/9
DO NOT CONNECT
BLACK - Ground
VEHICLE’S OBDII
CONNECTOR
RED/WHITE - Trunk Release (-) OutputOPTIONAL
CB
BCM HARNESS (BLACK CONN)
BCM HARNESS (GRAY CONN)
BCM HARNESS (BLACK CONN)
BCM HARNESS (GREEN CONN)
Body Control Module
Power Liftgate/Trunk Release
DE
HJ
FGK L
INSTALL GUIDEGUIDE ID: NI8_AL-XX70-B_RS-X70_20220131 Page 19 of 36
MODEL: OL-HRN-RS-NI8Wire Location Chart Diagram #3
Nissan Qashqai Std. Key 4 Cyl. Automatic 2019 - 2020
Body Control Module - - - - - Under Driver Side Dash
Horn WHITE 14 14 WHITE (-) At Horn Switch On Column
Lift Gate GREEN 8 6 LT.GREEN (-) At Liftgate Switch Lower Dash Panel
Nissan Rogue Std. Key 4 Cyl. Automatic 2018 - 2020
Body Control Module - - - - - Under Driver Side Dash
Horn WHITE 100 35 TAN (-) Driver Kick Panel
Lift Gate GREEN 8 6 LT.GREEN (-) At Liftgate Switch Lower Dash Panel
Nissan Rogue Sport Std. Key 4 Cyl. Automatic 2019 - 2020
Body Control Module - - - - - Under Driver Side Dash
Horn WHITE 100 79 PINK (-) Driver Kick Panel
Lift Gate GREEN 8 6 LT.GREEN (-) At Liftgate Switch Lower Dash Panel
Make Model Trim Year Item Connector Color
Connector Pins Pin # Wire Color Polarity Location
INSTALL GUIDEGUIDE ID: NI8_AL-XX70-B_RS-X70_20220131 Page 20 of 36
MODEL: OL-HRN-RS-NI8
DATA CABLE
RS-X70 Diagram #3
G
DPIN COLOR
1 BLUE2 RED3 GREEN3
1
N/CN/CN/C
C
B
PIN COLOR1 ORANGE2 WHITE/BLACK3 RED/WHITE4 LT. GREEN/BLACK5 GRAY6 VIOLET/WHITE7 BLACK/WHITE8 WHITE/BLUE9 YELLOW
10 LT. GREEN/RED11 BLACK12 BROWN13 BROWN/RED14 WHITE
18
714
N/C
N/C
N/CN/CN/CN/CN/C
N/CN/C
N/C
A
Door Lock Option A
Door Lock Option B
CAN Option B
CAN Option A
CONNECT
CB
BCM HARNESS (BLACK CONN)
BCM HARNESS (GRAY CONN)
BCM HARNESS (BLACK CONN)
BCM HARNESS (GREEN CONN)
Body Control Module
OL-H
RN-R
S-NI
8(B)
Connect PINK wires when using OL-HRN-RS-NI8(B) harness
BROWN - OEM Horn (-) OutputOPTIONAL
OEM Horn
GRAY - Connect to supplied hood pin IF no OEM hood pin is present
A
OL-HRN-RS-NI8(A)
OL-HRN-RS-NI8(D)DL-NI8/9BLACK -
Ground
VEHICLE’S OBDII
CONNECTOR
RED/WHITE - Trunk Release (-) OutputPower Liftgate
OPTIONAL
DE
HJ
FGK L
INSTALL GUIDEGUIDE ID: NI8_AL-XX70-B_RS-X70_20220131 Page 21 of 36
MODEL: OL-HRN-RS-NI8Wire Location Chart Diagram #4
Infiniti QX50 Push-to-Start Automatic 2019 - 2020
Body Control Module - - - - - Under Driver Side Dash
Horn WHITE 100 18 GRAY (-) Driver Kick Panel
Lift Gate WHITE 16 4 WHITE (-) At Liftgate Switch Lower Dash Panel
Make Model Trim Year Item Connector Color
Connector Pins Pin # Wire Color Polarity Location
INSTALL GUIDEGUIDE ID: NI8_AL-XX70-B_RS-X70_20220131 Page 22 of 36
MODEL: OL-HRN-RS-NI8
DATA CABLE
RS-X70 Diagram #4
G
DPIN COLOR
1 BLUE2 RED3 GREEN3
1
N/CN/CN/C
C
B
PIN COLOR1 ORANGE2 WHITE/BLACK3 RED/WHITE4 LT. GREEN/BLACK5 GRAY6 VIOLET/WHITE7 BLACK/WHITE8 WHITE/BLUE9 YELLOW
10 LT. GREEN/RED11 BLACK12 BROWN13 BROWN/RED14 WHITE
18
714
N/C
N/C
N/C
N/CN/CN/C
N/CN/C
N/C
A
CONNECT
Door Lock Option B
Door Lock Option A
CAN Option B
CAN Option A
CB
BCM HARNESS (BLACK CONN)
BCM HARNESS (GRAY CONN)
BCM HARNESS (BLACK CONN)
BCM HARNESS (GREEN CONN)
Body Control Module
OL-H
RN-R
S-NI
8(B)
Connect PINK wires when using OL-HRN-RS-NI8(B) harness
BROWN - OEM Horn (-) OutputOPTIONAL
OEM Horn
GRAY - Connect to supplied hood pin IF no OEM hood pin is present
A
OL-HRN-RS-NI8(A)
OL-HRN-RS-NI8(D)DL-NI8/9BLACK -
Ground
VEHICLE’S OBDII
CONNECTOR
RED/WHITE - Trunk Release (-) OutputTrunk Release
OPTIONAL
DE
HJ
FGK L
INSTALL GUIDEGUIDE ID: NI8_AL-XX70-B_RS-X70_20220131 Page 23 of 36
MODEL: OL-HRN-RS-NI8RS-X70 Optional Accessories
YELLOW - Alarm notifi cation input (+/-)
Antenna Cable
Push-Button LED Cable
F Antenna/LED Cable OR
Mod
el: L
INKR
-LT
ww
w.o
meg
alin
kr.c
om
G
G OL-ADAPTOR-B2G DATA CABLE
DATA CABLE
OR
G SENSOR CABLE
BLACK
GREEN
Data ShockSensorBLACK
RS-X70 MUST have V1.4 or newer fi rmware for Linkr-LT compatibility.
INSTALL GUIDEGUIDE ID: NI8_AL-XX70-B_RS-X70_20220131 Page 24 of 36
MODEL: OL-HRN-RS-NI8Installation Mode Selection
Module Programming
Press & hold programming button until LED turns solid GREEN to register selection.
2Press & release programming button to select installation mode.
LED flash (1x) once = Data Mode (Recommended)LED flashes (2x) twice = Hardwire Mode
1
Module Programming (cont.)
OR
Wait, the LED will turn OFF.
Turn the ignition to the ON position.1
Turn the ignition to the OFF position.
4
Wait, the LED will turn solid RED, then solid GREEN for 1 second, then solid RED.
3
ENGINESTARTSTOP
ENGINESTARTTTSTOP
OFF ACC STARTON
ENGINESTARTSTOP
ENGINESTARTTTSTOP
OFF ACC STARTON
5 Turn the ignition to the ON position.
ENGINESTARTSTOP
ENGINESTARTTTSTOP
OFF ACC STARTON
If LED flashes GREEN rapidly proceed with step 7. If LED turns solid GREEN for 2 seconds proceed to step 13.
WARNING:Disconnect power lastDisconnect module from vehicle.
WARNING: Do not press module programming button. Connect power first.Connect all other module connectors
10
Connect module to computer and proceed with extended programming.9
8
Turn the ignition to the OFF position.7
Proceed to RS-X70 Programming/Vehicle Learn.
Turn the ignition to the ON position.11
Turn the ignition to the OFF position.
14
Wait, the LED will turn solid GREEN for 2 second.
12
13
ENGINESTARTSTOP
ENGINESTARTTTSTOP
OFF ACC STARTON
ENGINESTARTSTOP
ENGINESTARTTTSTOP
OFF ACC STARTON
ENGINESTARTSTOP
ENGINESTARTTTSTOP
OFF ACC STARTON
6
2
INSTALL GUIDEGUIDE ID: NI8_AL-XX70-B_RS-X70_20220131 Page 25 of 36
MODEL: OL-HRN-RS-NI8
RS-X70 Programming/Vehicle Learn V1.6 (see installation guide for older versions)
Before You Begin:- Make sure all wires/harnesses are connected.- Program the bypass module to the vehicle per the instructions on the previous pages.- Connect any additional accessories/modules to the data ports.- MANUAL TRANSMISSION VEHICLES ONLY: Set the parking brake. The BLACK/WHITE wire must be connected to the parking brake wire.
Within 5 seconds of step 1 press the Valet button 3x or send remote start command (by remote, Linkr, activa-tion input wire etc.).
- The system will chirp & fl ash lights to indicate crankdelay (Default: 1 chirp/fl ash = 1.5 sec)
- Press valet button to change crank delay- Chirps: 1=1.5 sec, 2=15 sec, 3=20 sec, 4=30 sec
2
Programming complete.8
MANUAL TRANSMISSIONS: Release the parking brake.
AUTOMATIC TRANSMISSIONS: Turn the ignition key OFF.
- The system will chirp & fl ash the lights equal the #of IGN/ACC/START circuits detected (Max: 4).
MANUAL - Proceed to step 5.AUTOMATIC - Skip to step 6.
4
ENGINESTARTSTOP
ENGINESTARTTTSTOP
OFF ACC STARTON
ENGINESTARTSTOP
ENGINESTARTTTSTOP
OFF ACC STARTON Turn ignition to ON position (do not start).1
ENGINESTARTSTOP
ENGINESTARTTTSTOP
OFF ACC STARTON Start the engine with the key and let the engine reach normal idle.
3
TO SAVE SETTINGS/FINISH VEHICLE LEARN: Press the BRAKE pedal (will shut down RS).
- This disables VEHICLE LEARN (to enable again, programinstaller feature #2 (bank 10) to “Enabled”.
TO CANCEL/START OVER: Press the valet button once.
7
5 MANUAL TRANSMISSIONS: Set the parking brake again to enter Manual Transmission Reservation Mode option selection. (installer feature #11)
- The system will chirp & fl ash the light to indicate currentsetting (default: 2 - Off)
- Set and Release the parking brake to scrool through settingoptions.
- Chirp confi rmation: 1 = ON - Shutdown w/ lock, 2 = OFF,3 = ON - Shutdown w/ door close, 4 = ON - Shutdown 10sec. after door close
- Before turning the key OFF, perform the MT reservationsequence (see operation guide) and exit the vehicle.
6
TroubleShooting
- See system installation guide for remote start diagnostics and troubleshooting.- See OmegaLink module/fi rmware guide at www.wiresheet.com for interface module diagnostics and troubleshooting.
OR
Activate remote start (within 60 sec. of Step 4 or 5). Wait until engine is running and LED fl ashes slowly (10-45 seconds after engine cranks & runs).Push-to-Start vehicles: Ensure the OEM fob is at least 20 ft. away to allow remote start.
- The system will detect data protocols, select the bestavailable engine running detection method, and, learn anyavaialble tach input (data or analog).
3x
2x
2x
INSTALL GUIDEGUIDE ID: NI8_AL-XX70-B_RS-X70_20220131 Page 26 of 36
MODEL: OL-HRN-RS-NI8OL-MDB-ALL as Stand-Alone Layout
A B
E F G H
C D
INSTALLATION STEPS:1) Go to OmegaWeblink.com or use WebLink Mobile to flash the OL-MDB-ALL with the firmware matching the vehicle.
NOTE: If OEM remote is being used to activate the remote start be sure to enable “Factory keyless RS sequence” as “Lock + Lock + Lock” OR “Lock + Unlock + Lock”2) Make all the connections shown in the diagram on the following pages.3) Connect any optional RF kit or telematics device as needed.4) Program the OL-MDB-ALL to the vehicle (see “Module Programming” on the following pages).
NOTE: If an Omegalink RF (OL-RF-XX-SST) is used you will need to program the remotes at this time, Excalibur RF (RFK-XX-SST) kits will be pre-programmed from the factory.5) Test the system for all desired functions.
F WHITE 3 PIN
G WHITE 7 PIN
H WHITE 6 PIN
A BLACK 4 PIN DATA PORT
B BLACK 10 PIN
C PROGRAMMING/STATUS LED
D PROGRAMMING/RESET BUTTON
E BLUE 3 PIN
OL-MDB-ALL as Stand-Alone Installation Steps
INSTALL GUIDEGUIDE ID: NI8_AL-XX70-B_RS-X70_20220131 Page 27 of 36
MODEL: OL-HRN-RS-NI8Wire Location Chart Diagram #1
Nissan Rogue Push-to-Start 4 Cyl. Automatic 2014 - 2016Body Control Module - - - - - Under Driver Side Dash
Lift Gate GREEN 8 6 LT.GREEN (-) At Switch On Lower Dash
Nissan Rogue Std. Key 4 Cyl. Automatic 2014 - 2016Body Control Module - - - - - Under Driver Side Dash
Lift Gate GREEN 8 6 LT.GREEN (-) At Switch On Lower Dash
Make Model Trim Year Item Connector Color
Connector Pins Pin # Wire Color Polarity Location
INSTALL GUIDEGUIDE ID: NI8_AL-XX70-B_RS-X70_20220131 Page 28 of 36
MODEL: OL-HRN-RS-NI8OL-MDB-ALL as Stand-Alone Diagram #1
PIN COLOR1 GREEN/BLACK2 BLUE/BLACK3 RED/WHITE4 BROWN5 VIOLET/YELLOW6 VIOLET/BLACK7 WHITE8 BLACK/WHITE9 GREEN
10 VIOLET/WHITE N/C
N/CN/CN/CN/CN/CN/CN/C
1
10
B
Optional RF Kit/Telematics Port
DO NOT CONNECT
HOOD PIN Note: If vehicle is NOT equipped with a factory hood pin connect GREEN/BLACK wire to installed hood pin
OL-HRN-RS-NI8(C)RS-NI8/9
Door Lock Option A
Door Lock Option B
CAN Option A
CAN Option B
CB
BCM HARNESS (BLACK CONN)
BCM HARNESS (GRAY CONN)
BCM HARNESS (BLACK CONN)
OL-HRN-RS-NI8(A) Body Control Module
DO NOT CONNECT
DO NOT CONNECT
VEHICLE’S OBDII
CONNECTOR
ORANGE/WHITE - Trunk Release (-) OutputPower Liftgate
OPTIONAL
DE
HJ
FGK L
INSTALL GUIDEGUIDE ID: NI8_AL-XX70-B_RS-X70_20220131 Page 29 of 36
MODEL: OL-HRN-RS-NI8Wire Location Chart Diagram #2
Nissan Altima Push-to-Start Sedan Automatic 2019 - 2021Body Control Module - - - - - Under Driver Side Dash
Trunk Release GRAY 4 2 BROWN (-) At Liftgate Switch Lower Dash Panel
Nissan Qashqai Push-to-Start 4 Cyl. Automatic 2017 - 2020Body Control Module - - - - - Under Driver Side Dash
Lift Gate GREEN 8 6 LT.GREEN (-) At Liftgate Switch Lower Dash Panel
Nissan Qashqai Std. Key 4 Cyl. Automatic 2017 - 2018Body Control Module - - - - - Under Driver Side Dash
Lift Gate GREEN 8 6 LT.GREEN (-) At Liftgate Switch Lower Dash Panel
Nissan Rogue Push-to-Start 4 Cyl. Automatic 2017 - 2020Body Control Module - - - - - Under Driver Side Dash
Lift Gate GREEN 8 6 LT.GREEN (-) At Liftgate Switch Lower Dash Panel
Nissan Rogue Std. Key 4 Cyl. Automatic 2017 - 2017Body Control Module - - - - - Under Driver Side Dash
Lift Gate GREEN 8 6 LT.GREEN (-) At Liftgate Switch Lower Dash Panel
Nissan Rogue Sport Push-to-Start 4 Cyl. Automatic 2017 - 2020Body Control Module - - - - - Under Driver Side Dash
Lift Gate GREEN 8 6 LT.GREEN (-) At Liftgate Switch Lower Dash Panel
Nissan Rogue Sport Std. Key 4 Cyl. Automatic 2017 - 2018Body Control Module - - - - - Under Driver Side Dash
Lift Gate GREEN 8 6 LT. GREEN (-) At Liftgate Switch Lower Dash Panel
Make Model Trim Year Item Connector Color
Connector Pins Pin # Wire Color Polarity Location
INSTALL GUIDEGUIDE ID: NI8_AL-XX70-B_RS-X70_20220131 Page 30 of 36
MODEL: OL-HRN-RS-NI8OL-MDB-ALL as Stand-Alone Diagram #2
PIN COLOR1 GREEN/BLACK2 BLUE/BLACK3 RED/WHITE4 BROWN5 VIOLET/YELLOW6 VIOLET/BLACK7 WHITE8 BLACK/WHITE9 GREEN
10 VIOLET/WHITE N/C
N/CN/CN/CN/CN/CN/CN/C
1
10
B
Optional RF Kit/Telematics Port
DO NOT CONNECT
HOOD PIN Note: If vehicle is NOT equipped with a factory hood pin connect GREEN/BLACK wire to installed hood pin
OL-HRN-RS-NI8(C)RS-NI8/9
Door Lock Option A
Door Lock Option B
CAN Option B
CAN Option A
OL-HRN-RS-NI8(A)
VEHICLE’S OBDII
CONNECTOR
ORANGE/WHITE - Trunk Release (-) OutputOPTIONAL
CB
BCM HARNESS (BLACK CONN)
BCM HARNESS (GRAY CONN)
BCM HARNESS (BLACK CONN)
BCM HARNESS (GREEN CONN)
Body Control Module
Power Liftgate/Trunk Release
DE
HJ
FGK L
INSTALL GUIDEGUIDE ID: NI8_AL-XX70-B_RS-X70_20220131 Page 31 of 36
MODEL: OL-HRN-RS-NI8Wire Location Chart Diagram #3
Nissan Qashqai Std. Key 4 Cyl. Automatic 2019 - 2020Body Control Module - - - - - Under Driver Side Dash
Lift Gate GREEN 8 6 LT.GREEN (-) At Liftgate Switch Lower Dash Panel
Nissan Rogue Std. Key 4 Cyl. Automatic 2018 - 2020Body Control Module - - - - - Under Driver Side Dash
Lift Gate GREEN 8 6 LT.GREEN (-) At Liftgate Switch Lower Dash Panel
Nissan Rogue Sport Std. Key 4 Cyl. Automatic 2019 - 2020Body Control Module - - - - - Under Driver Side Dash
Lift Gate GREEN 8 6 LT.GREEN (-) At Liftgate Switch Lower Dash Panel
Make Model Trim Year Item Connector Color
Connector Pins Pin # Wire Color Polarity Location
INSTALL GUIDEGUIDE ID: NI8_AL-XX70-B_RS-X70_20220131 Page 32 of 36
MODEL: OL-HRN-RS-NI8
PIN COLOR1 GREEN/BLACK2 BLUE/BLACK3 RED/WHITE4 BROWN5 VIOLET/YELLOW6 VIOLET/BLACK7 WHITE8 BLACK/WHITE9 GREEN
10 VIOLET/WHITE N/C
N/CN/CN/CN/CN/CN/CN/C
1
10
B
Optional RF Kit/Telematics Port
OL-MDB-ALL as Stand-Alone Diagram #3
CONNECT
HOOD PIN Note: If vehicle is NOT equipped with a factory hood pin connect GREEN/BLACK wire to installed hood pin
OL-HRN-RS-NI8(C)RS-NI8/9
Door Lock Option A
Door Lock Option B
CAN Option B
CAN Option A
OL-HRN-RS-NI8(A)
VEHICLE’S OBDII
CONNECTOR
ORANGE/WHITE - Trunk Release (-) OutputPower Liftgate
OPTIONAL
CB
BCM HARNESS (BLACK CONN)
BCM HARNESS (GRAY CONN)
BCM HARNESS (BLACK CONN)
BCM HARNESS (GREEN CONN)
Body Control Module
DE
HJ
FGK L
INSTALL GUIDEGUIDE ID: NI8_AL-XX70-B_RS-X70_20220131 Page 33 of 36
MODEL: OL-HRN-RS-NI8Wire Location Chart Diagram #4
Infiniti QX50 Push-to-Start Automatic 2019 - 2020Body Control Module - - - - - Under Driver Side Dash
Lift Gate WHITE 16 4 WHITE (-) At Liftgate Switch Lower Dash Panel
Make Model Trim Year Item Connector Color
Connector Pins Pin # Wire Color Polarity Location
INSTALL GUIDEGUIDE ID: NI8_AL-XX70-B_RS-X70_20220131 Page 34 of 36
MODEL: OL-HRN-RS-NI8
PIN COLOR1 GREEN/BLACK2 BLUE/BLACK3 RED/WHITE4 BROWN5 VIOLET/YELLOW6 VIOLET/BLACK7 WHITE8 BLACK/WHITE9 GREEN
10 VIOLET/WHITE N/C
N/CN/CN/CN/CN/CN/CN/C
1
10
B
Optional RF Kit/Telematics Port
OL-MDB-ALL as Stand-Alone Diagram #4
CONNECT
HOOD PIN Note: If vehicle is NOT equipped with a factory hood pin connect GREEN/BLACK wire to installed hood pin
OL-HRN-RS-NI8(C)RS-NI8/9
Door Lock Option B
Door Lock Option A
CAN Option B
CAN Option A
CB
BCM HARNESS (BLACK CONN)
BCM HARNESS (GRAY CONN)
BCM HARNESS (BLACK CONN)
BCM HARNESS (GREEN CONN)
Body Control Module
OL-HRN-RS-NI8(A)
VEHICLE’S OBDII
CONNECTOR
Trunk Release
DE
HJ
FGK L
INSTALL GUIDEGUIDE ID: NI8_AL-XX70-B_RS-X70_20220131 Page 35 of 36
MODEL: OL-HRN-RS-NI8OL-MDB-ALL as Stand-Alone Optional Accessories
YELLOW - Alarm notification input (+/-) Mod
el: L
INKR
-LT
ww
w.o
meg
alin
kr.c
om
DATA CABLE
OL-MDB-ALL MUST have be flashed for Linkr compatibility
ADAPTOR Antenna Cable
OL-MDB-ALL MUST have be flashed for Excalibur RF Kit compatibility
Optional RF Kit/Telematics Port
Optional RF Kit/Telematics Port
H-OLRF4B Antenna Cable
OL-MDB-ALL MUST have be flashed for Omegalink RF Kit compatibility
Optional RF Kit/Telematics Port RED & BLACK - Not Used
RED & BLACK - Not Used
Not Used
OL-HRN-LINKR-ALL
INSTALL GUIDEGUIDE ID: NI8_AL-XX70-B_RS-X70_20220131 Page 36 of 36
MODEL: OL-HRN-RS-NI8OL-MDB-ALL as Stand-Alone Module Programming
OR
Wait, the LED will turn OFF.
Turn the ignition to the ON position.1
Turn the ignition to the OFF position.
4
Wait, the LED will turn solid RED, then solid GREEN for 1 second, then solid RED.
3
ENGINESTARTSTOP
ENGINESTARTTTSTOP
OFF ACC STARTON
ENGINESTARTSTOP
ENGINESTARTTTSTOP
OFF ACC STARTON
5 Turn the ignition to the ON position.
ENGINESTARTSTOP
ENGINESTARTTTSTOP
OFF ACC STARTON
If LED flashes GREEN rapidly proceed with step 7. If LED turns solid GREEN for 2 seconds proceed to step 13.
WARNING:Disconnect power lastDisconnect module from vehicle.
WARNING: Do not press module programming button. Connect power first.Connect all other module connectors
10
Connect module to computer and proceed with extended programming.9
8
Turn the ignition to the OFF position.7 Proceed to RS-X70 Programming/Vehicle Learn.
Turn the ignition to the ON position.11
Turn the ignition to the OFF position.
14
Wait, the LED will turn solid GREEN for 2 second.
12
13
ENGINESTARTSTOP
ENGINESTARTTTSTOP
OFF ACC STARTON
ENGINESTARTSTOP
ENGINESTARTTTSTOP
OFF ACC STARTON
ENGINESTARTSTOP
ENGINESTARTTTSTOP
OFF ACC STARTON
6
2