BI-TORQ® Valve Automation • PO Box 309 • 1N050 Linlar Dr. • La Fox, IL 60147 • tel: 630-208-9343 • fax: 630-232-6235 • www.bitorq.com

3

SERIAL NO.MODEL NO.

AVK CARBO-BOND INC.LA FOX IL. 60147

CLOSED

TORQUE OUTPUT 300 INCH POUNDS/35 NEWTON METERS

SUPPLY VOLTAGE 12VAC/DC 24VAC/DC 120VAC 230VAC

MAX INRUSH CURRENT 3.0A 0.8A 1.5A 1.0A

RUNNING CURRENT 0.5A 0.6A 0.5A 0.3A

CYCLE TIME 15 SEC 15 SEC 12 SEC 13 SEC

DUTY CYCLE (ON-OFF) 75% 75% 25%-50% 25%-50%

WEIGHT 5 POUNDS/2 KILOGRAMS

MECHANICAL CONNECTIONS ISO 5211 F03/F05 14MM

ELECTRICAL ENTRY (2) 1/2” NPT

ENCLOSURE RATING NEMA 4/4X

MANUAL OVERRIDE 8MM SOCKET DRIVE

CONTROL ON-OFF/JOG, 4-20MA PROPORTIONAL

ENCLOSURE MATERIAL POWDER COATED ALUMINUM

AMBIENT TEMPERATURE RATING -22°F TO +150°F-30°C TO +65°C

P1 Series Dimensional Data

F03/05 ISO Flange

Easily distinguishable yellow/red position

indicator

Heavy Duty Drive Motor

Easily accessible switch & cam stacks

ModularControlCards

Aluminum Casting4X Protection

Aluminum Casting4X Protection

NEMA 4Cover Seal

On/OffControl

P1 Series Exploded View

(2) 1/2” EMTPorts

14 V

er D

073

008

ProportionalControl

Paladin SerieS

P1 electric actuator SPecificationS

P1 electric actuator dimenSionS

P1 electric actuator exPloded View

BI-TORQ® Valve Automation • PO Box 309 • 1N050 Linlar Dr. • La Fox, IL 60147 • tel: 630-208-9343 • fax: 630-232-6235 • www.bitorq.com

4

SERIAL NO.MODEL NO.

AVK CARBO-BOND INC.LA FOX IL. 60147

CLOSED

Application Notes:1. These actuators are designed to be used in either a horizontal or upright position. Do NOT mount the actuator with the top below a horizontal position. 2. When installing conduit, use proper techniques for entry into the actuator. Use drip loops to prevent conduit condensate from entering the actuator. 3. Both NPT conduit ports MUST use proper equipment to protect the NEMA 4x integrity of the housing. 4. The internal heater is to be used in ALL applications. 5. Do NOT install the actuator outdoors or in humid environments unless it is powered up and the heater is functioning. 6. Use proper wire size to prevent actuator failure (see chart below for proper wire sizing). 7. Mechanical travel stops are factory calibrated for 90 degree operation. These stops are NOT designed to adjust mechanical rotation by more than +/- 3 degrees.

Wire sizing data is provided in the table below to assist in the selection of the proper wire size for P2/3 series actuators using various wire sizes over distance. Please make sure to reference the correct voltage and do not exceed the indicated length of the wire run for each model.

P2/3 Series Dimensional Data

Page 2 of 4 P2/3 HV AC Series

F07 ISO Flange

Switch Logic Map and Switch/Cam Arrangement

}}

3456791012

-5o 0 o 85o5 o 90o 95o

TB1

Term

inal

ID#

SW1 CLOSE Stop(Factory Set - Fixed)

SW2 OPEN Stop(Factory Set - Fixed)

AUX SW3(Factory Set - Adj)

AUX SW4(Factory Set - Adj)}

}

P Series Exploded View

Easily distinguishable yellow/red position

indicator

Worm Drive

Heavy Duty Drive Motor

Easily accessible switch & cam stacks

ModularControlCards

Clutchless OverrideHandwheel

Aluminum Casting4X Protection

Aluminum Casting4X Protection

NEMA 4Cover Seal

(Typical)

Switch sequencing data is provided in the table below to show the change-of-state points during the rotation of the actuator from OPEN to CLOSED and back again. Switches for terminals 3 thru 6 are set at the factory and should NOT be changed. The INCLUDED auxiliary switches SW3 & SW4 are for terminals 7 thru 12 and those setpoints may be modifi ed if need be. When so optioned, SW5 & SW6 auxiliary switches are initially set to function the same as auxiliary switches SW3 & SW4.

SD

08_P

23F0

78P

22 H

V A

C V

er D

121

808

Wire Sizing DataMAX distance between Actuator

and Supply (feet)

P2/3-2301.5A

10561659268141006970

10403

P2/3-1203.0A275433699

107018182714

WireGage18161412108

TORQUE OUTPUT 800 INCH POUNDS/90 NEWTON METERS

SUPPLY VOLTAGE 120VAC 230VAC

MAX INRUSH CURRENT 3.0A 1.5A

RUNNING CURRENT 1.0A 0.5A

CYCLE TIME 15 SEC 17 SEC

DUTY CYCLE (ON-OFF) 25% - 50% 25% - 50%

WEIGHT 25 POUNDS/11 KILOGRAMS

MECHANICAL CONNECTIONS ISO 5211 F07 22MM

ELECTRICAL ENTRY (2) 3/4” NPT

ENCLOSURE RATING NEMA 4/4X

MANUAL OVERRIDE 5” HANDWHEEL

CONTROL ON-OFF/JOG, 4-20MA PROPORTIONAL

ENCLOSURE MATERIAL POWDER COATED ALUMINUM

AMBIENT TEMPERATURE RATING -22°F TO +150°F-30°C TO +65°C

Paladin SerieS

P2 electric actuator SPecificationS

P2 electric actuator dimenSionS

P2 exPloded View