module 3 ac generators transformers ac motors

8/10/2019 Module 3 AC Generators Transformers AC Motors

1/57

Energy Systems Engineering Technology

AC Generators, Transformers, and AC Motors Module Page 1

College of Technology

Motors and Controls

Module # 3 AC Generators, Transformers, and AC Motors

Document Intent:

The intent of this document is to provide an example of how a subject matter expert might teach

AC Generators, Transformers, and AC Motors. This approach is what Idaho State University

College of Technology is using to teach its Energy Systems Instrumentation and Control

curriculum for AC Generators, Transformers, and AC Motors. The approach is based on a

Systematic Approach to Training where training is developed and delivered in a two step

process. This document depicts the two step approach with knowledge objectives being

presented first followed by skill objectives. Step one teaches essential knowledge objectives to

prepare students for the application of that knowledge. Step two is to let students apply what

they have learned with actual hands on experiences in a controlled laboratory setting.

Examples used are equivalent to equipment and resources available to instructional staff

members at Idaho State University.

Fundamentals of AC Generators, Transformers, and AC Motors Introduction:

This module covers fundamental aspects of AC Generators, Transformers, and AC Motors as

essential knowledge necessary to perform work safely according to national and local standards

on or around electrical power sources that are associated with motors and controls. Students will

be taught the fundamentals of AC Generators, Transformers, and AC Motors using classroom

instruction, demonstration, and laboratory exercises to demonstrate knowledge and skill mastery

of AC Generators, Transformers, and AC Motors. Completion of this module will allow students


2/57



to demonstrate mastery of knowledge and skill objectives by completing a series of tasks

demonstrating safe work practices on or around electrical power sources.

References

This document includes knowledge and skill sections with objectives, information, and examples

of how Motors and Control could be taught in a vocational or industry setting. This document

has been developed by Idaho State Universitys College of Technology. Reference material used

includes information from:

American Technical Publication Electrical Motor Controls for Integrated Systems, Third

Edition, by Gary J. Rockis and Glen A. Mazur, ISBN 0-8269-1207-9 (Chapter 7)

National Electrical Code International Electrical Code Series, NFPA 70TM

, NEC 2008,

ISBN-13: 978-087765790-3


3/57



STEP ONE

AC Generators, Transformers, and AC Motors Course Knowledge

Objectives

Knowledge Terminal Objective (KTO)

KTO 3. 1. ANALYZE AC Generators, Transformers, andAC Motors to compare

advantages and disadvantages to ensure they are correctly selected for applications

according to manufacturing specifications and electrical requirements

Knowledge Enabling Objectives (KEO)

KEO 3. 1. DESCRIBEwhat an AC GENERATORconsists of and its principle of

operation.

KEO 3. 2. DESCRIBEhow a SINGLE-PHASE AC GENERATORprovides AC Power.

KEO 3. 3. EXPLAINhow a three phase AC GENERATOR provides AC Power to

include operational characteristics and how they are connected to power AC

loads.

KEO 3. 4. Place Holder for Lawrence Beaty AC Generator Objective on how it is

taught and differs from Text Book.

KEO 3. 5. EXPLAIN three classifications of VOLTAGE CHANGES to include how they

occur, and how they are compensated.

KEO 3. 6. DESCRIBE a TRANSIENT VOLTAGEis and how devices can be protected

from H igh-L evel Transients.


4/57



KEO 3. 7. DESCRIBEwhat a TRANSFORMERis and how it effects Voltage.

KEO 3. 8. EXPLAINwhat TRANSFORMER LOSSESare and how they can be

minimized.

KEO 3. 9.

EXPLAINhow SINGLE-PHASEand THREE PHASE TRANSFORMER

CONNECTIONS are made to include both Primaryand Secondary Taps.

KEO 3. 10. EXPLAINwhat a CONTROL TRANSFORMERis and how they provide

control voltage lower than the Primary Voltageapplied.

KEO 3. 11. DESCRIBE two methods used to TROUBLESHOOT TRANSFORMERS.

KEO 3. 12. DESCRIBEwhat a SINGLE PHASEAC MOTORconsists of, its construction,

and principle of operation to include advantages they have over DC MOTORS.

KEO 3. 13. DESCRIBEthree types of SINGLE PHASEAC MOTORS to include: Shaded-

Pole, Split-Phase,and Capacitor motors.

KEO 3. 14. DESCRIBEwhat a THREE PHASEAC MOTORis to include operational

uses, and advantages they have over both DC Motorsand AC SINGLE PHASE

Motors.

KEO 3. 15. DESCRIBE SINGLE VOLTAGE and DUAL VOLTAGE THREE PHASE

MOTORapplications to include WYE and DELTAConnections.

KEO 3. 16. DESCRIBE AC MOTOR TROUBLESHOOTING TECHNIQUES to include:

TroubleshootingSingle Phase Shaded-Pole, Split -Phase, and Capacitor M otors,

andThree Phase Motors.


5/57



AC Generators, Transformers, and AC Motors

KEO 3. 1. DESCRIBEwhat an AC GENERATORconsists of, its components, and its

principle of operation.

AC GENERATORSconvert mechanical energy into electrical energy (the same way a DC

Generator does) by means of electromagnetic induction. AC GENERATORSare actually

referred to as ALTERNATORSbecause they convert mechanical energy into AC Vol tageand

Current(Al ternating Curr ent) They are similar to DC Generators in that both generators have

Field Winding and an Armature that rotates in a magnetic field.

AC GENERATORS consists of a F ield Winding, an Armature (Coil), Slip Ringsand Brushes

as depicted in the below picture:

Figure 7-1 page 141

F ield Windingsare magnets used to produce the magnetic field in a generator. The

magnetic field can be provided by permanent magnets or by Electromagnets. Most AC


6/57



Generators have their magnetic field generated by Electromagnets. Electromagnetsare

supplied with an external current to keep the magnetic field at its desired magnetic

strength.

An Armature (Coil) is the movable coil of wire that rotates through the magnetic field.

An Armature (Coil) may consist of many coils (similar to the armature in a DC

generator). The difference between the DC Generator and the AC Generator is:

o In a DC Generators Armature the ends of the coil(s) are attached to a

commutator.

o In n AC Generators Armature the ends of thecoil(s) are attached to slip r ings.

Slip Ringsare metallic rings connected to the ends of the armature coils(s) and are used

to connect the induced voltage to the generator s brushes. When the armature is rotated inthe magnetic field, a voltage is generated in each half of the armature coil. This voltage is

illustrated in the below sine wave of one revolution:

An AC Generator uses slip rings, which will allow the output current and voltage to

oscillate through positive and negative values. This oscillation of voltage and currenttakes the shape of a sine wave. This is typical of the AC Voltage we have in our homes

and industry throughout the world.


7/57



In DC Generators, a commutatoris used to provide an output whose current always

flowed in the positive direction as illustrated in the below figure:

Brushesin an AC Generatorare the sliding contact that rides against the slip rings and is

used to connect the armatureto the external AC Circuit. As the armature is rotated, each

half cuts across the magnetic lines of force at the same speed. Thus the strength of the

voltage induced in one side of the armature is always the same strength of the voltage

induced in the other side of the armature. Each half of the armature cuts the magnetic

lines of force in a different direction. As the armature rotates in the clockwise direction,

the lower half of the coil cuts the magnetic lines of force from the bottom up to the to the

left, while the top half of the coil cuts the magnetic lines of force from the top down to

the right. The voltage induced in one side of the coil, therefore, is opposite to the voltage

induced in the other side of the coil. The voltage in the lower left half of the coil enables

current flow in one direction, and the voltage in the upper half enables current flow in the

opposite direction. This means the voltage and current alternates in both directions as is

why it is called ALTERNATING CURRENT VOLTAGE (AC Voltage).

Since the two halves of the coil(s) are connected in a closed loop, the voltages add to

each other. The result is that the total of a full rotation of the armature is twice the voltage

of each coil(s) half. This total voltageis obtained at the brushesconnected to the slip

rings, and is applied to an external ci rcuit.


8/57



KEO 3. 2. DESCRIBEhow a SINGLE-PHASE AC GENERATORprovides AC Power.

A SINGLE-PHASE AC GENERATORprovides power through each complete rotation of its

armature within its magnetic field coils and produces one complete alternating current cycle. The

following picture depicts how the armature rotates 3600as it generates continuously changing

AC Sine Wave:

Figure 7-2 page 143


9/57



In the above picture, in position A, before the armature begins to rotate in a clockwise

direction, there is no voltage and no current in the external load circuit because the armature is

not cutting across any magnetic lines of force (O0

of rotation).

As the armature rotates from position Ato position B, each half of the armature cuts

across the magnetic lines of force, producing current in the external circuit. The current

increases from zero to maximum value in one direction. This changing value of current is

represented by the first quarter (900of rotation) of the sine wave.

As the armature rotates from position B to position C, the current continues inthe

same direction. The current decreases from its maximum positive value back to zero.

This changing value of current is represented by the second quarter (910- 180

0of

rotation) of the sine wave.

As the armature continues to rotate to position D, each half of the coil cuts across the

magnetic lines of force in the opposite direction. This changes the direction of current.

During this time, the current increases from its maximum negative value. This changing

value of current is shown by the third quarter (1810270

0of rotation) of the sine wave.

As the armature completes its rotation to position E (position A), the current is

deceased to zero, thus completing one 3600cycle of the sine wave.

KEO 3. 3. EXPLAINhow a three phase AC GENERATOR provides AC Power to

include operational characteristics and how they are connected to power AC

loads.

The same principles of a single phase AC Generator are the same for the three phase AC

Generatorexcept that there are there equally spaced armature windings 1200out of phase with

each other.


10/57



The below picture illustrates the differences between a single and a three phase generator

showing how three equally spaced armature windings 1200out of phase will create three output

voltages 1200out of phase with each other:

Figure 7-3 page 144

A Singl e Phase Generatorhas two leads providing power to the intended load. It is alternating

current that flow in both a positive and negative relationship to the (above and below) the 0 volt

reference point. Because a Thr ee Phase Generatorhas three separate armature windings so there

are six leads providing power to the intended load.


11/57



When the six leads are brought out from the Three Phase Generator, they are connected so that

only three leads appear for connection to the three different armature circuits. There are two

connections: Delta and Wye; the manner in which they are connected determines the electrical

characteristics of the generators output. The following picture depicts both the Delta and Wye

connections of a three phase generator:

Figure 7-4 page 145


12/57



A Delta Connectionis a connection that has each coil end connected end-to-end to form

a closed loop. In a Delta Connection, the three windings are all connected in series and

form a closed circuit. A Delta Connectionappears like the Greek Letter Delta ().

A Wye Connectionis a connection that has one end of each coil connected together and

the other end of each coil left open for external connections. A Wye Connectionappears

as the letter Y.

NOTE

The reasoning for the Delta and Wye Connections will be addressed later in this

curriculum as it has to do with AC Power distribution systems and AC Power connections

to three phase motors.

SUMMARY:

AC GENERATORSconvert mechanical energy into electrical energy (the same way aDC Generator does) by means of electromagnetic induction.

AC GENERATORS consists of a F ield Winding, an Armature (Coil), Slip Ringsand

Brushes.

F ield Windingsare magnets used to produce the magnetic field in a generator.

An Armature (Coil) is the movable coil of wire that rotates through the magnetic field.

Slip Ringsare metallic rings connected to the ends of the armature coils(s) and are usedto connect the induced voltage to the generator s brushes.

Brushesin an AC Generatorare the sliding contact that rides against the slip rings and isused to connect the armatureto the external AC Circuit.

A SINGLE-PHASE AC GENERATORprovides power through each complete rotation

of its armature within its magnetic field coils and produces one complete alternating

current cycle.

The same principles of a single phase AC Generator are the same for thethree phaseAC Generatorexcept that there are there equally spaced armature windings 120

0out of

phase with each other.

A Singl e Phase Generatorhas two leads providing power to the intended load.

A Three Phase Generatorhas three separate armature windings so there are six leadsproviding power to the intended load.

There are two connections: Delta and Wye; the manner in which they are connecteddetermines the electrical characteristics of the generators output.

A Delta Connectionis a connection that has each coil end connected end-to-end to forma closed loop

A Wye Connectionis a connection that has one end of each coil connected together and

the other end of each coil left open for external connections.


13/57



KEO 3. 4. Place Holder for Lawrence Beaty AC Generator Objective on how it is

taught and differs from Text Book.

KEO 3. 5. EXPLAIN three classifications of VOLTAGE CHANGES to include how they

occur, and how they are compensated.

VOLTAGE CHANGES need to be monitored and controlled. AC Generators are designed to

produce an out voltage. In addition, all electrical and electronic equipment is rated for operation

at a Specif ic Voltage. The standard rated voltage is a voltage that equipment can operate safely

can vary in a range of +5% to -10%of the equipments voltage requirements. This voltage range

is used because an Over-Voltageis generally more damaging than an Under-Voltagecondition.

Equipment Manufacturers, Utility Companies, and regulating agencies must routinely

compensate for changes in system voltage.

Backup Generatorsare used to compensate for voltage changes. A Backup Generatorcan bepowered by diesel, gasoline, natural gas, or propane engines connected to the generator.

If there is any power interruption in the time period between the loss of main utility power and

when the generator starts providing power, the generator is usually classified as a standby

(emergency) power supply. VOLTAGE CHANGESin a system may be categorized as:

Momentary, Temporar y, orSustainedas depicted in the below picture:

Figure 7-5 page 146


14/57



A Momentary Power I nterr uption is a decrease to 0 Volts on one or more of the three

phase power lines lasting from .5 cycles up to 3 seconds. All power distribution systems

have momentary power interruptions during normal operation. The interruptions can be

caused when L ightn ing Stri kes Nearby, Util ity Grid Switching dur ing a problem(short

on one line, or during Open Cir cuit Tr ansiti on Switching(a process in which power is

momentarily disconnected when switching a circuit from one voltage supply or level to

another).

A Temporary Power I nterr uptionis a decrease to 0 Volts on one or more power lines

lasting more than 3 seconds up to 1 minute. Automatic circuit breakers and other circuit

protection equipment protect all power distribution systems. Circuit protection equipment

is designed to remove faults and to restore power. Automatic circuit breakers normally

take 20 cycles to about 5 seconds to close. If the power is restored, the power interruption

is only temporary. A Temporary Power I nterr uptioncan also be caused by a time gapbetween power interruptions and when a back-up power supply (generator) takes over, or

if someone accidently opens the circuit by switching the wrong circuit breaker and then

turns it back on.

A Sustained Power I nterruptionis a sustained power interruption when the power

decreases to 0 Volts on all power lines for a period of longer than one minute. All power

distribution systems have a complete loss of power at some time. They are caused as a

result of Storms, Tripped Circuit Breakers,Bl own F uses,and orDamaged Equipment.

The effect of a power interruption on a load depends on the load and the application. If a power

interruption could cause equipment, production, and or security problems that are not acceptable,

an Unin terr uptable Power System/Supply (UPS)can be utilized. An Uninterr uptable Power

System/Suppl y (UPS)is a power supply that provides constant power needs when the main

power supply is interrupted. This is accomplished by a network of electronics and batteries such

that the incoming AC power from the main utility is used to convert the AC to DC to keep the

batteries charged and then it inverts the DC back to clean uninterrupted and filtered AC power to

which the facility that utilizes this UPS will not experience a power interruption upon loss of the

main utility power source. A large facility will also have a backup generator with a UPS to pick

up the emergency designated power in the event the UPS main battery(s) lose their ability to

keep their charge. For long power interruption protection (sustained), a combination of a

generator and a UPS are used. For short power interruptions (temporary), a UPS is used. UPS

batteries are generally sealed lead acid batteri es.


15/57



Uninterruptable Power System/Suppl ies (UPS)are also used to keep loads like important

business computing systems and medical equipment powered up at all times in the event of a

power loss. These UPS units have the load running directly from them and are constantly being

kept charged by the facilities main power source. An example of a Common UPSis the power

supply provided to a laptop computer. When the laptop is plugged into a power source, it keeps

the internal battery charged. When the laptop is not plugged into a power source, it is running off

the internal battery. The internal battery provides power to the laptop with or without an outside

power supply as long as the battery can last without being charged.

There are also Portable AC Generators of various sizes used to provide power during temporary

power interruptions as depicted below:

Picture at bottom of page 146

These generators are utilized in Recreational Vehicles to provide AC power when they are not

connected to a power supply in and on construction sites where power has not yet been

established, and in residences for temporary power outages.

NOTE:

Portable generators SHOULD NEVER be connected to a residence or utility power source

to back-feed AC power when the utility power has been lost. This is because the portable

generator and utility power are not synchronized and this could cause a fire and or

explosion, which can cause death or injury as well as serious equipment damage.

AC Backup Generators are designed for temporary or sustained power interruptions. They

are provided with an automatic transfer switch that senses loss of power, starts the

generator, and picks up essential or emergency power loads.


16/57



When the power is restored, the transfer switch automatically resets and allows only the

utility power to be available without a second power loss (this transfer is instantaneous).

When power is initially lost, there is a short interruption of incoming power until the

generator comes up to speed and assumes the load. There is no interruption upon return of

the incoming utility power. The following two pictures are of a backup generator:

Backup 120/240 VAC Natural Gas Generator

Backup Generator Transfer Switch connected to

a residential 120/240 VAC Main Power Panel.


17/57



SUMMARY:

VOLTAGE CHANGES need to be monitored and controlled.

An Over-Voltageis generally more damaging than an Under-Voltagecondition. Equipment Manufacturers, Utility Companies, and regulating agencies must routinely

compensate for changes in system voltage.

Backup Generatorsare used to compensate for voltage changes and can be powered bydiesel, gasoline, natural gas, or propane engines connected to the generator.

VOLTAGE CHANGESin a system may be categorized as: Momentary, Temporary, orSustained.

A Momentary Power I nterr uption is a decrease to 0 Volts on one or more of the three

phase power lines lasting from .5 cycles up to 3 seconds.

A Temporary Power I nterr uptionis a decrease to 0 Volts on one or more power lines

lasting more than 3 seconds up to 1 minute.

A Sustained Power I nterruptionis a sustained power interruption when the powerdecreases to 0 Volts on all power lines for a period of longer than one minute.

Unin terruptable Power System/Suppl ies (UPS)are also used to keep loads likeimportant business computing systems and medical equipment powered up at all times in

the event of a power loss.

UPS units have the load running directly from them and are constantly being kept

charged by the facilities main power source.

Portable generators SHOULD NEVERbe connected to a residence or utility powersource to back-feed AC power when the utility power has been lost. This is because the

portable generator and utility power are not synchronized and this could cause a fire and

or explosion, which can cause death or injury as well as serious equipment damage.

Portable generatorscan be used to provide temporary power to essential loads by theuse of extension cords plugged directly to an essential load like a heater or refrigerator

that has been unplugged from the utility powered receptacle.


18/57



KEO 3. 6. DESCRIBE a TRANSIENT VOLTAGEis and how devices can be protected

from H igh-L evel Transients.

A TRANSIENT VOLTAGEis a temporary, unwanted voltage in an electrical circuit.

Transient Voltages are normally erratic, large voltages or spikes that have a short duration and a

shout rise time. Devices like Computers, Electronic Circui ts (TVsMicro Wave Ovens

Sound Systems etc)require protection against Transient Vol tages. Protection methods usually

include proper wiring to National Electrical Code Requirements, to include grounding, shielding

of the power lines, and use of Surge Protectors.

A Surge Protectoris an electrical device that provides protection from high-level

transient voltages by limiting the level of voltage allowed downstream from the Surge

Protector/Suppressor (more commonly called a Surge Suppressor). Surge

Protector/Suppressorscan be installed at service entrance panels and individual loads as

depicted in the below picture:

Figure 7-6 page 147


19/57



Surge Suppressorspower strips as shown above generally will have and on off switch and areset button. When they trip the power is removed from the loads and the device needs to be

manually reset to restore power to the loads. If the power surge was high enough, it could

actually damage the Suppressor and it will not reset.

Surge Suppressors are under a UL listing and requirements (IEC 61643-1,EN 61643-11and 21 ,Telcordia Technologies Technical ReferenceTR-NWT-001011,ANSI /IEEE

C62.xx, orUL)and mandated that all units manufactured after August 17, 1998 must pass

all test procedures outlined in the second edition of UL1449 to continue to be listed and

labeled as UL1449.

SUMMARY:

Transient Voltages are normally erratic, large voltages or spikes that have a short

duration and a shout rise time.

Devices like Computers, Electronic Circits (TVs

M ir cro Wave Ovens

SoundSystems etc)require protection against Transient Vol tages.

Protection methods usually include proper wiring to National Electrical CodeRequirements, to include grounding, shielding of the power lines, and use of Surge

Protectors.

A Surge Protectoris an electrical device that provides protection from high-level

transient voltages by limiting the level of voltage allowed downstream from the Surge

Protector/Suppressor (more commonly called a Surge Suppressor).

Surge Suppressorspower strips generally have and on off switch and a reset button.

When Surge Suppressorstrip the power is removed from the loads and the device needsto be manually reset to restore power to the loads.

If the Power Surgewas high enough, it could actually damage the Suppressor and it willnot reset.

KEO 3. 7. DESCRIBEwhat a TRANSFORMERis and how it effects Voltage.

A TRANSFORMERis an electrical device that uses electromagnetism to change voltage from

one level to another. In other words, the Voltage is Stepped Up orStepped Down. Transformers

are used in electrical distribution systems to increase or decrease the voltage and current safely

and efficiently.

They are used to increase voltage to a H igh Level for Transmissionacross the country and then

to decrease that voltage to a Low Level for useto a variety of electrical loads (residential,

commercial, and industrial).
http://en.wikipedia.org/wiki/International_Electrotechnical_Commissionhttp://en.wikipedia.org/wiki/CENELEChttp://en.wikipedia.org/wiki/Telcordia_Technologieshttp://telecom-info.telcordia.com/site-cgi/ido/docs.cgi?ID=SEARCH&DOCUMENT=TR-NWT-001011&http://en.wikipedia.org/wiki/American_National_Standards_Institutehttp://en.wikipedia.org/wiki/Institute_of_Electrical_and_Electronics_Engineershttp://en.wikipedia.org/wiki/Underwriters_Laboratorieshttp://en.wikipedia.org/wiki/Underwriters_Laboratorieshttp://en.wikipedia.org/wiki/Institute_of_Electrical_and_Electronics_Engineershttp://en.wikipedia.org/wiki/American_National_Standards_Institutehttp://telecom-info.telcordia.com/site-cgi/ido/docs.cgi?ID=SEARCH&DOCUMENT=TR-NWT-001011&http://en.wikipedia.org/wiki/Telcordia_Technologieshttp://en.wikipedia.org/wiki/CENELEChttp://en.wikipedia.org/wiki/International_Electrotechnical_Commission


20/57



An example of how Transformers accomplish this is depicted in the below picture:

Figure 7-7 page 148

Transformers allow power utility companies to distribute large amounts or power at a

reasonable cost. Large Transformers are used for power distribution along city streets and in

large manufacturing or commercial buildings. These distributions are done both above and below

ground locally and mostly overhead for long distances.

The larger transformers are maintained by qualified workers specially trained in H igh Voltage

Transformer Operation and Maintenance. Technicians will often work with small transformers.

Control Transformers are used to isolate the power circuit from the control circuit, providingadditional safety for the circuit operator or technician. Transformersare also used in power

suppliesof most electron ic equipment to Step-Up or Step-Down the l ine voltageto provide the

required operating voltage for the equipment.


21/57



Transformershave a Primary Windingand a Secondary Windingwound around an I ron Core

as depicted in the below picture:

Figure 7-8 page 148

The Primary Windingis the coil that draws the power from its source and the Secondary

Winding is the coil of the transformer that delivers the energy at the transformed or changed

voltage. A Transformer Transfers AC Energyfrom one circuit to another. This transfer is made

magnetically through the iron core as the magnetic field builds up around a wire when AC is

passed through the wire. The magnetic field builds up and collapses each half cycle because the

wire is carrying AC as depicted below:

Figure 7-9 page 149


22/57


23/57



The following picture depicts a H igh-Voltage Transmission Stationwhere thousands of volts

are received via overhead transmission lines and then transformed to a lower voltage for local

distribution:

Picture page 150


24/57



SUMMARY:

A TRANSFORMERis an electrical device that uses electromagnetism to changevoltage from one level to another (the Voltage is Stepped Up orStepped Down).

TRANSFORMERS are used to increase voltage to a H igh Level for Transmission

across the country and then to decrease that voltage to a Low Level for useto a variety ofelectrical loads (residential, commercial, and industrial).

KEO 3. 8. EXPLAINwhat TRANSFORMER LOSSESare and how they can be

minimized.

Many TRANSFORMERShave a secondary coil that has an extr a lead (tap)attached to it. A

Tapis a connection brought out of a winding at a point between its endpoints to allow changingthe voltage or current ratio.

Although Transformersare very efficient, they are not perfect. Not all energy delivered to the

primary side by the source is transferred to the secondary load circuit. There is a majority of

energy lost as heat in the transformer. There are three types of TRANSFORMER LOSSES in

an iron core transformer: Resistive Losses, Eddy Current Loses, and Hysteresis Losses.

Resistive Lossescome from the resistance of the coil winding. When current passes

through the winding, the winding will heat up and lose energy that could have been

transferred to the secondary. These losses are inherent and cannot be minimized.

Eddy Cur rent Losses come because iron i s a fair conductor of electricity.This is due to

the varying magnetic field which induces a voltage in the secondary winding that also

induces small voltages in the iron core of the transformer. The small voltages produce

Eddy Cur rents, which in turn produce heat. This heat also represents a loss because it

does not useful work.

o Eddy Cur rent L osses are minimized either by making the core of thin sheets

(laminations) which are insulated from each other, or by powered-iron coresinstead of solid blocks of iron.

o The insulation between the laminationsof a laminated core break up current

paths within the core and reduces Eddy Cur rents. This same technique is used to


25/57



reduce Eddy Cur rents in Solenoids and was addressed in: Module # 2 Solenoids

DC Generators and DC Motors.

Hysteresis Losesoccur each time the magnetizing force produced by the primary side of

a transformer changes, the atoms of the core realign themselves in the direction of the

force. This energy required to realign the iron atoms must be supplied by the input power

and is not transferred to secondary load current.

o Hysteresis Loses are minimized by using H igh Sil icon Steel and other alloys in

the construction of the core.

All three of these TRANSFORMER LOSSESmake the typical iron core transformer hot when

operating under full load. The transformer may be too hot to touch based on its size and load, but

there shoul d be no odor of bur ri ng insulation or varni sh, or sings of discoloration or smoke.

Any one of these conditions indi cates the transformer is either over loaded or defective andservice is necessary to correct and reduce damage, safety, or fir e hazards.

SUMMARY:

A


26/57



KEO 3. 9. EXPLAINhow SINGLE-PHASEand THREE PHASE TRANSFORMER

CONNECTIONS are made to include both Primaryand Secondary Taps.

SINGLE-PHASE CONNECTIONSutilize only one of the three phases of power distributed by

the electrical utility. This Single Phase power is utilized throughout the world in residential

applications and smaller businesses that do not require three phase power. The following picture

depicts how Residential Electrical Power is provided by overhead 3-phase or lateral (under-

ground) service as required by the National Electrical Code:

Figure 7-11 page 151


27/57



THREE-PHASE CONNECTIONSutilize all three phases of power in the same manner where

each phase is Stepped-Down like it is with a single phase using three separate identical

transformers.

The following pictures depict: Transformer Secondary Tap, Centered-Tap, configurations to

obtain a variety of different voltages:




28/57



KEO 3. 10. EXPLAINwhat a CONTROL TRANSFORMERis and how they provide

control voltage lower than the Primary Voltageapplied.

A CONTROL TRANSFORMERis a transformer that is used to Step-Down the voltageto the

control circuit for a system or machine. The most common Control Transformers have two

primary coils and one secondary coil as illustrated in the following three pictures:

Figure 7-14 page 152 Figure 7-15 page 153



29/57



As depicted above, control vol tage can be reduced from 480 VAC to 240 VAC and down to 120

VAC. Control Transformers are also designed to drop a control voltage down to 24 VAC as

well , which is a much safer less hazardous voltage for technicians to work on and

troubleshoot contr ol cir cui ts. I n all cases the Stepped-Down voltage reduces the amount of

voltage used to control a circuit operating on higher voltages.

Transformer specification sheets are used to obtain required information when selecting

the proper transformer for an application as depicted below:



30/57



Picture Page 153 Control Transformers

Picture Page 154 Autotransformers


31/57


32/57



The following picture depicts how using a DMM can be used to test transformers:



33/57



SUMMARY:

L

l

KEO 3. 12. DESCRIBEwhat a SINGLE PHASEAC MOTORconsists of, its construction,

and principle of operation to include advantages they have over DC MOTORS.

A SINGLE PHASEAC MOTORis an AC motor that uses Al ternating Cur rent (AC) to

produce rotati on. The main parts of an AC motor are the Rotor, and a Stator. The Rotoris the

rotating part of the motor and the Statoris the stationary part of an AC motor. A typical AC

motor is used in industry because of their Simplicity, Ruggedness, and Reliabilityand can be

Single Phase, Singl e Phase Two Speed Single Voltage, and Three Phase Single or Dual

Voltageas depicted below also illustrating typical construction characteristics:



34/57



AC motors have several advantages over DC motors in that there are only two bearings that can

wear, and there are No Brushesbecause the motor does not have a Commutatorwhich reduces

the need for extra maintenance associated with DC Motors.

Single Phase Motors are commonly used in residential applications for AC Motor

Driven appliances such as:Forced Ai r Furnace Fans, Ai r Conditioners, Washing

Machines, etc.Single Phase Motors include: Shaded-Pole, Spli t-Phase,and Capacitor

motors.

KEO 3. 13. DESCRIBEthree types of SINGLE PHASEAC MOTORS to include: Shaded-

Pole, Split-Phase,and Capacitor motors.

Shaded-Polemotors are a Single Phase AC Motorthat uses a shaded stator pose for

starting the motor as depicted in the picture below:

[ Insert Figure 7-20 page 157 Rockis Book) ]


35/57



Shaded-Polemotors utilize the simplest method to start a Single Phase AC Motor. They

are commonly rated at horsepower or less and have low starting torque. Common

applications include small cooling fans found in computers and home entertainment

centers. The Shaded-Poleis normally a solid single turn of copper wire placed around a

portion of the main pole laminations as indicated in the above picture.

o This shaded pole delays the magnetic field in the area of the pole that is shaded.

This shading causes the magnetic field at the pole area to be positioned

approximately 900from the magnetic field of the main Stator F ield Pole. This

movement determines the starting direction of a shaded pole motor.

o A shaded-pole motor is a type ofACsingle-phaseinduction motor.It is basically

a smallsquirrel cage motor in which the auxiliary winding is composed of a

copper ring surrounding a portion of each pole. This auxiliary winding is called ashading coil. Currents in this coil delay thephase ofmagnetic flux in that part of

the pole enough to provide arotating magnetic field.The direction of rotation isfrom the unshaded side to the shaded (ring) side of the pole. The effect produces

only a low startingtorque compared to other classes of single-phase motors.

o These motors only have one winding, no capacitor nor starting switch, making

them economical and reliable. Because their starting torque is low they are bestsuited to driving fans or other loads that are easily started. Moreover, they are

compatible withTRIAC-based variable-speed controls, which often are used with

fans. They are built in power sizes up to about 1/6 hp or 125 watts output. Forlarger motors, other designs offer better characteristics.

Split-Phasemotors are Single Phase AC M otorsthat include a Running (main winding)and a Starting Winding (auxiliary winding). Split-Phasemotors are AC motors of a

fractional horsepower, usually1/20 to

1/3HP. They are commonly used to operate washing

machines, oil burners, and small pumps and blowers.

o A Split-Phasemotor has a rotating part (rotor), a stationary part consisting of the

running and starting winding (stator), and a centrifugal switch that is located

inside the motor to disconnect the start winding at 60% to 80% of designed full

speed.
http://en.wikipedia.org/wiki/Alternating_currenthttp://en.wikipedia.org/wiki/Single-phase_electric_powerhttp://en.wikipedia.org/wiki/Induction_motorhttp://en.wikipedia.org/wiki/Squirrel_cage_motorhttp://en.wikipedia.org/wiki/Phase_(waves)http://en.wikipedia.org/wiki/Magnetic_fluxhttp://en.wikipedia.org/wiki/Rotating_magnetic_fieldhttp://en.wikipedia.org/wiki/Torquehttp://en.wikipedia.org/wiki/TRIAChttp://en.wikipedia.org/wiki/TRIAChttp://en.wikipedia.org/wiki/Torquehttp://en.wikipedia.org/wiki/Rotating_magnetic_fieldhttp://en.wikipedia.org/wiki/Magnetic_fluxhttp://en.wikipedia.org/wiki/Phase_(waves)http://en.wikipedia.org/wiki/Squirrel_cage_motorhttp://en.wikipedia.org/wiki/Induction_motorhttp://en.wikipedia.org/wiki/Single-phase_electric_powerhttp://en.wikipedia.org/wiki/Alternating_current


36/57



o A Split-Phasemotor is depicted in the below picture:


When the Split-Phasestarts, both the Runningand Start Windingsare connected in

parallel. The Start Windingis used to jump start the motor and then is disconnected by

the centrifugal switch at 60% to 80% of full speed. When the motor is turned off, the

centrifugal switch returns to its normally closed position (at approximately 40% of its full

speed), ready to be used for starting the motor again.

A Capacitor Motor is also a Spli t-Phase AC M otorthat includes a capacitor in addition to

the running and starting windings. Capacitor Motorsrange in sizes ranging from1

/8to 10HP. Capacitor Motors are used to operate Refr igerators, Compressors, Washing Machines,

and Air Conditioners.


37/57



o The Capacitor is wired in ser ies with the Start Winding and provides a Capacitor

Start Motor with the benefi t of H igh Starting Torque. The Capacitor adds an extra

jump start to get the motor to start with loads requiring High Starting Torque. A

Capacitor Start Motoris depicted below:


A Capacitor -Run Motoris aSpli t-Phase AC M otorwith the start winding and the capacitor

connected in series at all times which does not have a centrifugal switch, giving this motormedium staring torque and somewhat higher running torque than a capacitor start motor as

the capacitor continually charges and discharges while the motor is running.


38/57



o A Capacitor-Run Motoris depicted in the below picture:


A Capacitor Start-and-Run motor (used to run refrigerators and compressors) uses two

capacitors with one used to start the motor, and the other one used as a capacitor to allow the

motor to continue operating as a Capacitor Run Motor.This motor uses a larger capacitor tostart the motor and a smaller one to run it.


39/57



o A Capacitor Start-and-Run motordepicted below with a centrifugal switch cutting

out the start capacitor and allowing the run capacitor to stay in the start winding:


A Capacitor Start-and-Run motor has the same starting torque as a capacitor

start motor.

A Capacitor Start-and-Run motor has more running torque that a capacitor-

start motor or a capacitor-run motor.

SUMMARY:

.


40/57



KEO 3. 14. DESCRIBEwhat a THREE PHASEAC MOTORis to include operational

uses, and advantages they have over both DC Motorsand AC SINGLE PHASE

Motors.

THREE PHASEAC MOTORS are the most commonly used motors in industrial applications.

Three PhaseAc Motorsare used in applications ranging from fractional horsepower to over 500

HP. Three PhaseAc Motorsare used in most applications because they are simple in

construction, require little maintenance, and cost less to operate than Single Phase or DC

Motors. The most common Three PhaseAc Motoris the I nduction Motor.

The I nduction Motoris a motor that has three sets of Rotor Coils with each connected a

different phase of the three phase power. These composite windings are the Phase A, B,

and C of the three phase power. An Induction Three Phase Motor is illustrated below

with different colors per phase in the Rotor and in the Voltage Sine Wave:

Figure 7-25page 161


41/57



o Three Phase Motorsare like having three single phase motors connected together to

do more work more efficiently. Each phase is 1200from the other phases and the

magnetic field is produced in the stator because each phase reaches its peak magnetic

strength 1200from the other phases. They are self starting and do not require an

additional starting method because of the rotating magnetic field in the motor.

o Three Phase Motorsare designed as either Single-Voltage Motorsor Dual-Voltage

Motors.


42/57



KEO 3. 15. DESCRIBE SINGLE VOLTAGE and DUAL VOLTAGE THREE PHASE

MOTORapplications to include WYE and DELTAConnections.

SINGLE VOLTAGE THREE PHASE MOTORSis a motor that operates at only one

voltage level. They are less expensive to manufacture than Dual Voltage Motors, but are

limited to locations having the same voltage as the motor.

o Common Single Voltage Three Phase Motors ratings are 230, 460, and 575 VAC.

Other ratings include 200, 208, and 220 VAC.

o All Single Voltage Three Phase Motorsare wired so that the phases are connected in

either a (Y) or a () configuration as illustrated in the following two pictures:

Three Phase Wye-Connected Motor



43/57



o A Wye-Connected Motor has one end of each coil internally connected to the other

phases.

Three Phase Delta-Connected Motor


o A Delta-Connected Motor has each phase coil wired end-to-end to form a

completely closed loop.

A DUAL VOLTAGE THREE PHASE MOTOR is manufactured so that they may beconnected for either of two voltages. Making motors for two voltages enables the same

motor to be used with two different three phase power supplies.


44/57



o The normal dual-voltage rating for three phase motors is 230/460 VAC. In either case

the motor uses the same amount of power and gives the same horsepower output for

either voltage, but as the voltage doubles from 230 VAC to 460 VAC, the current is

cut in half.

o Using a reduced current enables the use of a smaller gauge wire, thus reducing the

cost of installation. Like Single Voltage motors, Dual Voltage motors can also be

connected in either a (Y) or a () configuration as illustrated in the following two

pictures:


45/57



Dual Voltage Three Phase Wye-Connected Motor


A Dual Voltage Wye-Connected Motor has each phase coil divided into two equal

parts.


46/57



Three Phase Delta-Connected Motor


A Dual Voltage Delta-Connected Motor has each phase coil divided into two equal

parts.

KEO 3. 16. DESCRIBE AC MOTOR TROUBLESHOOTING TECHNIQUES to include:

TroubleshootingSingle Phase Shaded-Pole, Split -Phase, and Capacitor M otors,

andThree Phase Motors.

Most problemswith AC Motors are related to Single Phase AC M otors dealing with the

Centr if ugal Switch, Thermal Switch, or Capacitors. These motors are usually serviced and

repaired if the problem is related to the centrifugal switch, thermal switch, or capacitors. If a

motor is less than1/8HP it is usually replaced as the cost to repair can exceed the replacement

cost. As for Three Phase AC Motors, they usually operate for many years without anyproblems as they have fewer components that may malfunction than Single Phase AC or DC

Motors.

AC Motor Maintenance is extremely important and if maintained properly, many motor

failures can be minimized or in some cases prevented. In general, electrical motors are very

dependable and will provide good service under the conditions in which the motor was designed

to operate within. To provide the safest service possible, a technician should check a motor name

plate prior to putting it in service to ensure that the proper voltage and current are being used.

The below picture depicts the type of information found on a motors name plate:



47/57



Any standard motor should not be operated in very damp locations or where water may enter the

motor frame. There are specially designed motors for such locations with enclosures are

available to totally enclose a motor from damp or wet locations.

The frame of a motor should be grounded to prevent anyone receiving an electrical shock in the

event the motor has developed a short. Motors in damp locations are at a greater risk of causing ashock hazard. The reason for grounding motors is that it is common practice for a technician to

feel the motor to see if it has overheated and using a bare hand to feel a motor is done. Using a

temperature indicating device or infrared temperature detector should also be used to check for a

motor that may be overheated.

To prevent an ordinary motor from becoming overheated, keep the air openings on its frame

clear at all times. When oiling motor bearings, be sue not to use excessive oil as it could damage

the motor winding resistance and could cause the motor to collect an excessive amount of dirt

and dust.

When inspecting or replacing a motor, a technician should ensure the enclosure meets the proper

specifications as detailed in the below picture:


48/57




An open motor enclosure allows the air to flow through the motor to cool the windings to

prevent overheating. A totally enclosed motor prevents air from entering the motor and cooling

is provided by other means.

If a motor does not start rotation after the switch has been turned ON, TURN OFF THE MOTOR

and UNPLUG it to prevent any permanent damage to the motors windings from becoming

overheated.

The above methods discussed are preventive maintenance activi tiesthat a facility should have

in place to keep its motors operating safely and efficiently. If done properly, all motors will

provide longer service life and continue to operate efficiently.

Troubleshooting Shaded-Pole Single Phase AC M otorswhen they fail are usually replaced.

The reason for the motor failure needs to be investigated to ensure the replacement motor not

subject due to an overload situation or environmental conditions that may have caused its

failure. To Troubleshoot a Shaded-Pole Motor the following picture illustrates a two step

process:


49/57




To Troubleshoot a Shaded-Pole Single Phase AC Motor, the following procedure may

be used:

1.

Visually Inspectthe motor after turning power off (lock-out and tag-out).

a. Replace the motor if you see any discoloration showing it has been too hot.

b. Replace the motor if the shaft if jammed or lock as the bearings have seized.

c. Replace the motor if there is any sign of damage to the motor.

2. Check Stator Winding as it is the only electrical circuit that may be tested without

taking the motor apart.

a. Measure the resistance of the stator winding at the lowest DMM scale to

verify an infinity reading.

b. Replace the motor if the DMM indicates a zero reading (continuity) even

though the winding may still be good.

c. A final check can also be performed on the coil using a MEGOHMEETER to

verify the coil does not break down with voltage applied.

Troubleshooting Split-Phase Single Phase AC M otorsgenerally looking at a thermal switch

that automatically turns OFF the motor when it has overheated. These thermal switches may

have a manual reset or an automatic reset when the motor has cooled down. Caution must be

taken with any motor that has an automatic reset because the motor may automaticallyrestart at any time. The following picture illustrates how to Troubleshoot Spli t-Phase Single

Phase AC Motors:


50/57




To Troubleshoot a Split-Phase AC Motor, the following procedure may be used:

1. Visually Inspectthe motor after turning OFF the power (lock-out tag-out)

a. Replace the motor if you see any discoloration showing it has been too hot.

b. Replace the motor if the shaft if jammed or lock as the bearings have seized.

c. Replace the motor if there is any sign of damage to the motor.

2. Check for Thermal Switch.

a. With the motor power ON, check to see if a thermal switch exists, if it does,

Reset the switch and turn the motor on if it is a manual reset switch. If it

starts, observe it for normal operation.


51/57



3. If it does not start, Checkfor voltage at the motor terminals using a DMM set to

measure voltage. The voltage should be within 10% of the motor listed voltage. If

voltage in not present or incorrect, continue troubleshooting the voltage problem.

4. If the motor voltage is good, turnOFF the motor (lock-out tag-out) to continue

testing the motor.

5. With power removed, connect a DMM set to resistance to the same motor leads

receiving the power (disconnect the motor leads from the incoming power leads to

ensure accurate measurement of motor leads). A short circuit is present if the

DMM reads Zero and an open circuit is present if the meter reads infinity. In

either case, the motor will need to be replaced and in most cases they are normally

too small for repair to be cost efficient.

6.

Check for Centrifugal Switch if present look for signs of burning or brokensprings.

a. Service or replace the switch if any obvious signs of problems exist.

b. Check the resistance of the switch. If the switch does not indicate it is open,

manually operate the switch with the DMM still connected to verify proper

operation (open and closed). To do this the end-bell on the switch may have to

be removed. The resistance on the DMM decreases if the motor is good. If

problem exists, the resistance will not change.

Troubleshooting Capacitor Motorsis similar to troubleshooting Split-Phase Motors. The

only additional device to be tested is the Capacitor.Capacitorshave a limited life and are

often the problem with Capacitor Motors. They may develop short circuit internally, or

become an open circuit. In either case they need to be tested and replaced as necessary

and they eventually deteriorate to the point when then must be replaced.

Deterioration may also change the value of a Capacitor, which will cause additional

problems. When it shorts out, the winding in the motor could actually burn out and need

to be replaced. When it deteriorates or opens, the motor will have poor starting torque,

which can prevent the motor from starting or more often usually trips the motor overload

devices (interlock switches).

Capacitorsdesigned to be connected to AC Power do not have an established polarity

like in a DC Power circuit. The following picture illustrates the steps on how to

troubleshoot a capacitor motor:


52/57




To Troubleshoot Capacitor Single-Phase AC Motors, the following procedure may be

used:

1. Lock-Out and Tag-Out the handle of the safety switch or combination starter

in the OFF positon.

2. Measure the Voltage at the terminals to ensure the power is off (Zero

Voltage Check)

3. Remove Cover from Capacitorwhich are usually located on the outside of

the motor frame. CAUTION: A good capacitor will hold a charge even

when the power is removed.

4. Visually Inspect Capacitorfor any signs of leakage, cracks, or bulges. If any

of these conditions are present, the capacitor will need to be replaced.


53/57


54/57




To Troubleshoot a Three Phase motor, the following procedure may be used:

1. Measure Voltage at Motor Terminalsto verify voltage if present and at the

correct value on all three phases. If all the voltage is not present for all three

phases, the power supply voltage must be checked and restored. If the voltage ispresent and correct but the motor will still not start, proceed to the next step.

2. Lock-Out and Tag-Out the incoming power to the motor and its controls per

proper procedures.


55/57



3. Disconnect the Load from the Motorto see if the motor in not locked by the

load.

4. Restore Power by removing the Lock-Out Tag-Out Tag per proper

procedure and try restarting the motor. If the motor starts, the load needs to be

checked for problems that have caused the motor not to rotate. If the motor does

not start with the load removed, proceed to the next step.

5. Lock-Out and Tag-Out the incoming power to the motor and its controls per

proper procedures.

6. Check the Motor Windings with DMM to measure resistance for any opens, or

short circuits for all coils. This is can be a check across all coils, or to check

indivudal coils, they will need to be isolated as indicated in the above pictureillustrating how to Troubleshoot Three Phase Motors.

a. If checking one coil first to determine its resistance, the basic laws of

series and parallel circuits are applied for series or parallel connected

coils. This can be used to check all coils together and if a problem exists,

then each coil will have to be checked to determine where the problem

may exist.

TECHNICAL FACTS ON 3 PHASE MOTORS:


56/57




57/57

module 3 ac generators transformers ac motors

Documents