monarch page 1 marley monarch - roof source · monarch page 1 marley monarch description &...
TRANSCRIPT
The classic concrete bold roll tile in the Mediterranean tradition
Monarch page 1
Marley Monarch
Description & Technical data 7 pages
Inland KwaZulu-Natal Western Cape
Tile range, Fittings & Accessories
Nominal tile size: 420 x 332 mm
Nominal hanging length: 390 mm
Nominal tile mass: 5 kg
Nominal cover width 301 mm
Monarch page 3
at lock mid-shuffl e position:
Undertile membrane
Technical data
Minimum roof pitch with 100 mm headlap with 75 mm headlap
The side interlock provides for apractical 2 mm play between the tiles(± 1 mm either way of the nominal cover)which gives fl exibility when setting outthe roof and helps to achieve the correctperpendicular alignment of the courses.
17,5˚ 26˚
Rafter/Trusses As per structural requirements
Rafter centres 760 mm with 38 x 38 mm batten(maximum) 900 mm with 38 x 50 mm batten fi xed fl at 1 000 mm with 38 x 50 mm batten on edge
Note: Above 760 mm the rafter spacing can be increased only withengineer-designed trusses and with 38 x 50 mm batten of the correctgrade. All structural timber must comply with S.A National Standards.
Marley high-quality Undertile Membrane is recommended in all cases.Modern practice has demonstrated that the undertile membrane is a fundamental part of a tiled roof at pitches below 26° and for pitches above 45°, and at all pitches in exposed and coastal areas.
Tiling data at pitches of 17,5° to 25°
Tiling data at pitches of 26° and above
Minimum tile headlapMaximum batten centresBatten per m² (net length)Tiles per m² (net)Mass of tiles per m² ±
100 mm320 mm3,13 m10,4851,9 kg
Minimum tile headlapMaximum batten centresBatten per m² (net length)Tiles per m² (net)Mass of tiles per m² ±
75 mm345 mm2,9 m9,6348,2 kg
Distance from top edge of fi rst battento outside edge of fascia board
Distance from top edge of top batten to rafter apex
Estimating See Eaves and Rafter tables
335 mm
25 mm
All tiling and fi xing to comply with SANS 10062 : 2003 Code of Practice and with Marley standard fi xing specifi cations.
Cutting and drilling of tiles: See Health & Safety instruction
45˚
26˚
17,5˚
1. The minimum pitch and minimum headlap must not be reduced under any circumstance. It is always better to raise the safety factor of the roof by adding a full course of tiles and increasing the tile headlap evenly on the rafter length.2. In exposed areas the tile headlap may be increased, but greater lap is not as effective as a steeper pitch.
Number of tiles on the rafter length at minimum headlap
Roof pitches of:
17,5º to 25º 26º and more 100 mm headlap 75 mm headlap
Rafter length Rafter length
1m
2m
3m
4m
5m
6m
7m
8m
9m
10m
11m
12m
Rafter Table
Eaves Table
The Rafter Table indicates the number of coursesto be allowed on the rafter length to ensure thatthe minimum tile headlap of 100 mm or 75 mmis obtained according to the roof pitch.
The Eaves Table shows the average linearcoverage for Monarch tiles along the eaves length.Calculations are given at lock mid-shuffl e position,subject to standard manufacturing tolerances.
All fi gures are net. Wastage must be added.
© Marley Roofi ng 2010
1
2
3
4
5
6
7
8
9
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
10
11
12
13
14
15
16
17
18
19
1
2
3
4
5
6
7
8
9
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
10
11
12
13
14
15
16
17
18
19
0,360
0,680
1,000
1,320
1,640
1,960
2,280
2,600
2,920
3,240
3,560
3,880
4,200
4,520
4,840
5,160
5,480
5,800
6,120
6,440
6,760
7,080
7,400
7,720
8,040
8,360
8,680
9,000
9,320
9,640
9,960
10,280
10,600
10,920
11,240
11,560
11,880
12,200
0,360
0,705
1,050
1,395
1,740
2,085
2,430
2,775
3,120
3.465
3,810
4,155
4,500
4,845
5,190
5,535
5,880
6,225
6,570
6,915
7,260
7,605
7,950
8,295
8,640
8,985
9,330
9,675
10,020
10,365
10,710
11,055
11,400
11,745
12,090
Above 45º pitchconsult themanufacturer
11,77
0
12,07
1
12,37
2
12,67
3
12,97
4
13,27
5
13,57
6
13,87
7
14,17
8
14,47
9
14,78
0
15,08
1
15,38
2
15,68
3
15,98
4
16,28
5
16,58
6
16,88
7
17,18
8
17,48
9
17,79
0
18,09
1
18,39
2
18,69
3
18,99
4
19,29
5
19,59
6
19,89
7
20,19
8
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67
12m 13m 14m 15m 16m 17m 18m 19m 20m
300
.
32 300
332
332. . . .300
. . ...
.
75
..
.
30
.
....
420
.
.
Monarch M22-coated
Monarch Designer Range
The superior performance proven M22-coated tile provides guaranteed long-lastingcolour uniformity on the roof. Acid-rain tested, formulated to prevent algal and fungalgrowth, it is recommended for all applications − Highly suitable for humid coastal regions
The Monarch Designer Range enables architects and developers to create strikinglybeautiful roofs in the classic mediterranean tradition with standard or special blends.
Monarch page 5
For beautiful roofs in the classic Mediterranean tradition
Monarch page 7
Next...
Tuscany special Blend
MONARCH INLAND — FITTINGS and ACCESSORIES
Quality corrosion-resistant integrated stormclipsmanufactured from ZIAL
‘SOLO-FIX’ stormclips
®
Monarch tile: Code 85-48 S
Packaging: 500 clips per box
It is important to use the correct clip for the tile
profile.
Undertile membrane
Colour: White traditionalNet coverage per roll 45 m²Printed 150 mm headlap dotted line
Monarch tile minimum length 90 mm
M22 touch-up coatingfor mortarbedding, flashings, fascia boards
etc. per 1, 2 and 5 litre
2 ply 400 micron polypropylene laminate
Mortar pigment in all colours per kg
Tile nails
Agrément Certificate 2008/341
All tile accessories, undertile membrane, tiling nails, stormclips, pigment,
M22 touch up coating etc.are available ex-factory.
2 ply 400 micron polypropylene laminatewith insulation foil
Agrément Certificate 2007/333
Printed 150 mm headlap dotted line
• HEAVY INDUSTRIAL — Reinforced two sided foil
Agrément Certificate 2009/353
Agrément Certificate 2009/353
• RESIDENTIAL — One sided foil
• RESIDENTIAL/COMMERCIAL — Two sided foil
Net coverage per roll 45 m²
Net coverage per roll 45 m²
Net coverage per roll 50 m²
Marley ‘Radiant Barrier’
97% heat reflective
Energy saving
Serrated nails for rake verge tiles 75 mm
Next... KwaZulu-Natal Range
Overlapping fittings
Taper ridge tile2,7 per m
Ventilated ridge tile Rake verge tile3,2 per m
Taper hip starter120º capped
ridge tile 2,3 per m
Butt joint fittings
120º ridge tile 2,2 per m
MarleyUniversalRidge Tile System
MarleyUniversal
RakeVerge TileSystem
Monoridge tile2,7 per m
MONARCH KWAZULU-NATAL FITTINGS and ACCESSORIES
Quality corrosion-resistant integrated stormclipsmanufactured from ZIAL
‘SOLO-FIX’ stormclips
®
Monarch tile: Code 85-48 S
Packaging: 500 clips per box
It is important to use the correct clip for the tile
profile.
Undertile membrane
Colour: White traditionalNet coverage per roll 45 m²Printed 150 mm headlap dotted line
Minimum length for Monarch tile 90 mm
M22 touch-up coatingfor mortarbedding, flashings, fascia boards
etc. per 1, 2 and 5 litre
2 ply 400 micron polypropylene laminate
Mortar pigment in all colours per kg
Tile nails
Agrément Certificate 2008/341
All tile accessories, undertile membrane, tiling nails, stormclips, pigment,
M22 touch up coating etc.are available ex-factory.
2 ply 400 micron polypropylene laminatewith insulation foil
Agrément Certificate 2007/333
Printed 150 mm headlap dotted line
• HEAVY INDUSTRIAL — Reinforced two sided foil
Agrément Certificate 2009/353
Agrément Certificate 2009/353
• RESIDENTIAL — One sided foil
• RESIDENTIAL/COMMERCIAL — Two sided foil
Net coverage per roll 45 m²
Net coverage per roll 45 m²
Net coverage per roll 50 m²
Marley ‘Radiant Barrier’
97% heat reflective
Energy saving
Serrated nails for rake verge tiles 75 mm
Next... Western Cape Range
Overlapping fittings
Taper ridge tile2,5 per m
Ventilated ridge tileRake verge tile3,2 per m
Taper terminal ridge tile
Taperhip starter
120ºcapped ridge tile2,3 per m
Halfround capped ridge tile1,9 per m
Butt joint fittings
120ºridge tile2,2 per m
Ventilated ridge tile
Shellhip starter
120ºterminalridge tile
90ºridge tile 2,2 per m
Monoridge tile 2,2 per m
MarleyUniversalRidge Tile System
MarleyUniversal
RakeVerge TileSystem
MONARCH WESTERN CAPE FITTINGS and ACCESSORIES
Quality corrosion-resistant integrated stormclipsmanufactured from ZIAL
‘SOLO-FIX’ stormclips
®
Monarch tile: Code 85-48 S
Packaging: 500 clips per box
It is important to use the correct clip for the tile
profile.
Undertile membrane
Colour: White traditionalNet coverage per roll 45 m²Printed 150 mm headlap dotted line
Monarch tile 100 mm
M22 touch-up coatingfor mortarbedding, flashings, fascia boards
etc. per 1, 2 and 5 litre
2 ply 400 micron polypropylene laminate
Mortar pigment in all colours per kg
Agrément Certificate 2008/341
All tile accessories, undertile membrane, tiling nails, stormclips, pigment,
M22 touch up coating,DPC, birdcomb etc.
are available ex-factory.
2 ply 400 micron polypropylene laminatewith insulation foil
Agrément Certificate 2007/333
Printed 150 mm headlap dotted line
• HEAVY INDUSTRIAL — Reinforced two sided foil
Agrément Certificate 2009/353
Agrément Certificate 2009/353
• RESIDENTIAL — One sided foil
• RESIDENTIAL/COMMERCIAL — Two sided foil
Net coverage per roll 45 m²
Net coverage per roll 45 m²
Net coverage per roll 50 m²
Marley ‘Radiant Barrier’
97% heat reflective
Energy saving
Serrated nails
Rake verge tiles 75 mm
Back to Quickfinder
Overlapping fittings
Taper ridge tile 2,5 per m Rake verge tile 3,2 per m
Taperhip starter
Butt joint fittings
120º ridge tile 2,2 per m
Monoridge tile 2,7 per m
Butt joint hip starter
MarleyUniversalRidge Tile System
MarleyUniversal
RakeVerge TileSystem
Use only serrated nails in Western Cape coastal regions