monolithic isolating joints · is a true monolithic isolating joint which effectively and...
TRANSCRIPT
Monolithic Isolating Joints
OTHER PRODUCTS AVAILABLE• Kleerband® Flange Protectors• Radolid® Nut Protective Caps• Casing Insulators and End Seals• Innerlynx® - Modular Mechanical Seals• Cathodic Isolating Gaskets• Foreman Night Caps• Safety Spray Shields• U-Bolt Cote® - Coated U-bolts
TO ORDER PLEASE SPECIFY THE FOLLOWING:1. Diameter of pipe 2. ANSI rating3. Grade of pipe material4. Wall thickness5. Product to be transported6. Temperature of transported material (160°F is standard. Higher temperature materials available upon request.)7. Additional X-ray, Non-destructive testing. Electrical and hydrostatic testing is standard. (Please state requirements)
Distributed by:
PO Box 60399 • Lafayette, Louisiana 70596-0399800-315-6009 • 337-233-6116 • FAX 337-232-3860E-Mail: [email protected] • Website: www.apsonline.com
Advance Products & Systems, LLC is not responsible for errors printed in this brochure.
BSI TM
ISO 9001FM 537405
Advance Products & Systems, LLC shall repair or replace (within the limitations of such applicable express written warranty as may be issued by it) any product or portions thereof, which prove to be defective in workmanship or material for a period of 12 months from shipment date. The foregoing in lieu of all warranties, express or implied, and all other obligations or liabilities on the part of APS, on account of the product which it may sell. In no event shall APS be liable for consequential or special damages: nor except as it may otherwise specifically agree in writing, installation, or other work which may be done upon or in connection with the product by APS/ the distribution / dealer or others. THE LIMITED WARRANTIES PROVIDED IN THIS AGREEMENT AND THE OBLIGATIONS AND LIABILITIES OF APS ARE THE ONLY WARRANTIES MADE BY APS AS TO THE PRODUCT. APS MAKES NO EXPRESS OR OTHER IMPLIED WARRANTIES, BY COURSE OF DEALING, USAGE OF TRADE, MERCHANTABILITY, FITNESS FOR A PARTICULAR USE (WHETHER GENERAL OR SPECIFIC), OR OTHERWISE.
I S O - 9 0 0 1 C e r t i f i e d C o m p a n y - F M 5 3 7 4 0 5
072516
Isojoint® Benefits & Advantages -see pages 4-5
Isojoint® Design -see page 3
IsoJoInt® MonolIthIc IsolatIon JoInts
one piece units, field problems are virtually non-existent and the integrity of the isolation is kept intact.
Furthermore, once installed, IsoJoInt® can be buried and forgotten ending your maintenance worries. In contrast, inspection pits and vaults must be used to monitor below ground isolation gaskets. And constant visual inspections of above ground isolation gaskets are necessary to check for shorts in the gaskets. This requires a continuing maintenance program during the entire life of the pipeline.
90” Diameter IsoJoInt® Monolithic Isolation Joint
IsoJoInt® For superIor CathodIC proteCtIonIsoJoInt® is a true monolithic isolating joint which effectively and efficiently stops short circuits and stray currents from damaging pipelines and equipment. IsoJoInt® employs one or more, preassembled pressure seals and isolating ring. Unlike isolating gasket kits, IsoJoInt® does not depend on an installer fitting gasket, sleeves and washers into a flange on location. Any one of these parts could be damaged causing a complete breakdown of the isolated flange, thus loosing cathodic isolation. Because IsoJoInts® are welded into place as
1520253240506580
100125150200250300350400450500600700800900
10001050110012001400
1/2”3/4”
1”5/4”6/4”
2”2 1/2”
3”4”5”6”8”
10”12”14”16”18”20”24”28”32”36”40”42”44”48”56”
21,326,933,742,448,360,376,188,9
108,0/114,3133,0
159,0/168,3219,1273,0323,9355,9406,4457,0508,0610.0711,0813.0914,0
1016,01067,01118,01219,01422,0
3,23,23,23,63,65,55,05,66,36,37,18,08,88,8
10,011,011,012,012,514,214,216,018,018,020,022,024,0
60,365,076,188,988,9
101,6133,0139,7177,8193,7273,0323,9355,6457,0457,0508,0610,0660,0810,0865,0975,0
1118,01225,01321,01321,01422,01710,0
120120120120120141161161204204237237267244247342342332332300300500500500700
10001000
120120120120120145157157208208237237277254251336336313313300300500500500700
10001000
60606060606482828888
126126156202202222222355355400400400400400400500500
300300300300300350400400500500600600700700700900900
1000100010001000140014001400180025002500
1,41,62,02,73,54,08,0
10,019,035,053,071,093,0
180,0180,0224,0340,0480,0710,0950,0
1250,02270,02240,02428,02680,03800,04500,0
in
DN ANSI 600 (PN 100)
1520253240506580
100125150200250300350400450500600700800900
10001050110012001400
1/2”3/4”
1”5/4”6/4”
2”2 1/2”
3”4”5”6”8”
10”12”14”16”18”20”24”28”32”36”40”42”44”48”56”
21,326,933,742,448,360,376,188,9
108,0/114,3133,0
159,0/168.3219,1273,0323,9355,9406,4457,0508,0610,0711,0813,0914,0
1016,01067,01118,01219,01422,0
3,23,23,23,63,65,55,05,66,36,37,17,17,18,08,08,08,88,8
10,012,514,214,216,016,018,020,020,0
60,365,076,188,988,9
101,6133,0139,7177,8193,7273,0323,9355,6457,0457,0508,0610,0660,0810,0865,0975,0
1118,01225,01321,01321,01422,01710,0
120120120120120141161161204204237237287284284282337387387342342500500500700
10001000
120120120120120145157157208208237237287284284256340390390345345500500500700
10001000
60606060606482828888
126126126132132162223223223313313400400400400500500
300300300300300350400400500500600600700700700700900
1000100010001000140014001400180025002500
1,41,62,02,73,54,08,0
10,019,035,053,083,085,0
120,0140,0165,0300,0350,0600,0750,0910,0937,0
1702,01680,01820,02010,02850,0
ANSI 300 (PN 65)
mm
.125
.125
.125
.141
.141
.216
.196
.220
.248
.248
.279
.314
.346
.346
.393
.433
.433
.472
.492
.559
.559
.629
.708
.708
.787
.866
.944
2.3742.5592.9963.5003.5004.0005.2365.5007.0007.625
10.74812.75014.00017.99217.99220.00024.01525.98431.88934.05538.38544.00048.22852.00052.00055.98467.322
gn min BB A B C L WeightAAmm in kglbs
.9171.0591.3261.6691.9012.3742.9963.500
4.250/4.5005.236
6.259/6.6258.625
10.74812.75114.011
1617.992
2024.01527.992
3235.984
404244
47.99255.984
mm in mm in mm in
4.7244.7244.7244.7244.7245.5516.3386.3388.0318.0319.3309.330
10.5119.6069.724
13.46413.46413.07013.07011.81111.81119.68519.68519.68527.55939.37039.370
4.7244.7244.7244.7244.7245.7006.1816.1818.1888.1889.3309.330
10.90510.0009.881
13.22813.22812.33212.33211.81111.81119.68519.68519.68527.55939.37039.370
2.3622.3622.3622.3622.3622.5193.2283.2283.4643.4644.9604.9606.1417.9527.9528.7408.740
13.97613.97615.74815.74815.74815.74815.74815.74819.68519.685
11.81111.81111.81111.81111.81113.77915.74815.74819.68519.68523.62223.62227.55927.55927.55935.43335.43339.37039.37039.37039.37055.11855.11855.11870.86698.42598.425
33.54.5689
18224277
117156205397397494749
1058156520942756500449385353590883779921
mm inmm inmm in
in
DN
mmgn min BB A B C L WeightAA
mm in kglbsmm in mm in mm inmm inmm inmm in
.9171.0591.3261.6691.9012.3742.9963.500
4.250/4.5005.236
6.259/6.6258.625
10.74812.75114.011
1617.992
2024.01527.992
3235.984
404244
47.99255.984
2.3742.5592.9963.5003.5004.0005.2365.5007.0007.625
10.74812.75014.00017.99217.99220.00024.01525.98431.88934.05538.38544.00048.22852.00052.00055.98467.322
.125
.125
.125
.141
.141
.216
.196
.220
.248
.248
.279
.279
.279
.314
.314
.314
.346
.346
.393
.492
.559
.559
.629
.629
.708
.787
.787
4.7244.7244.7244.7244.7245.5516.3386.3388.0318.0319.3309.330
11.29911.18111.18111.10213.26715.23615.23613.46413.46419.68519.68519.68527.55939.37039.370
4.7244.7244.7244.7244.7245.7006.1816.1818.1888.1889.3309.330
11.29911.18111.18110.07813.38515.35415.35413.58213.58219.68519.68519.68527.55939.37039.370
2.3622.3622.3622.3622.3622.5193.2283.2283.4643.4644.9604.9604.9605.1965.1966.3778.7798.7798.779
12.32212.32215.74815.74815.74815.74819.68519.685
11.81111.81111.81111.81111.81113.77915.74815.74819.68519.68523.62223.62227.55927.55927.55927.55935.43339.37039.37039.37039.37055.11855.11855.11870.86698.42598.425
33.54.5689
18224277
117183187265309364661772
132316532006206637523704401244316283
1 6
IsoJoInt® MonolIthIc IsolatIon JoInts
IsoJoInt® provides for current control by separating pipe work into distinct zones and effectively eliminating long-line currents. This assures increased plant and equipment life by reducing or eliminating corrosion damage. Effective control can be attained where a branch is connected to the mainline, where two pipelines of different material connect or where well-coated pipe meets a poorly coated system.
Advance Products and Systems, LLC, is the exclusive provider of the
IsoJoInt® monolithic weld end isolating joints. The IsoJoInt® is manufactured in sizes ranging from 1/2” diameter to 150” diameter with an ANSI rating of 150# to 2500# and up to API 10,000#. All types of carbon and stainless steel are used in their manufacturing.
For truly superior cathodic isolation, Advance Products and Systems offers an IsoJoInt® manufactured according to ASME VIII Division 1 standards and certified by ISO 9001 Quality Assurance making it the supreme monolithic joint on the market today.
G-10 Isolating RingG-10 Isolating Ring
Isolating Filling Material
Zone A
Zone B
Insulating Coating
Isolating Filling Material
This cutaway illustrates the typical isolating properties of IsoJoInt®
Double Seal Gasket System
1520253240506580
100125150200250300350400450500600700800900
10001050110012001400
1/2”3/4”
1”5/4”6/4”
2”2 1/2”
3”4”5”6”8”
10”12’’14”16”18”20”24”28”32”36”40”42”44’’48’’56”
21,326,933,742,448,360,376,188,9
108,0/114,3133,0
159,0/168,3219,1273,0323,9355,9406,4457,0508,0610,0711,0813,0914,0
1016,01067,01118,01219,01422,0
3,23,23,23,23,63,64,04,55,05,05,66,36,37,17,18,08,08,08,88,8
10,010,011,011,012,512,514,2
33,733,742,451,060,376,1
101,6108,0133,0159,0193,7244,5298,5355,6406,4445,0508,0545,0655,0758,0860,0965,0
1070,01125,01175,01275,01480,0
200200200200200200220220240250250300320300300300300350350350400400450450550500700
205205205205205210215215235240240300320300300300300350350350400400450450550500700
454545454560
115115125160160200260300300300300300300300300300400400400500500
450450450450450470550550600650650800900900900900900
1000100010001100110013001300150015001900
0,51,01,31,82,13,04,56,0
10,025,028,060,065,0
110,0120,0200,0210,0215,0225,0304,0387,0437,0705,0730,0824,0
1100,01558,0
in
mmgn min BB A B C L Weight
DN ANSI 150 (PN 25)
mm
AA
BB
gn
B
C
A
L + 5
ANSI 150 (PN 25) ANSI 300 (PN 65) & ANSI 600 (PN 100)
L + 5
B
C
A
BBAA
gn
Basic Parameters of Insulating Joints
ANSI 150 (PN 25)• Maximum Operating Pressure, bar - 25,0 (363 psi)• Pressure of Strength Test, PT, bar - 37,5 (544 psi)• Working Temperature Range TS, °F - -4° to 158°• Electrical voltage AC 5kV(50Hz) in 1 min. time (in dry condition) • Resistance at voltage DC 1kV (in dry condition) R,MΩ - 10,0
ANSI 300 (PN 65)• Maximum Operating Pressure, bar - 63,0 (914 psi)• Pressure of Strength Test, PT, bar - 94,5 (1370 psi)• Working Temperature Range TS, °F - -4° to 212°• Electrical voltage AC 5kV(50Hz) in 1 min. time (in dry condition)• Resistance at voltage DC 1kV (in dry condition) R,MΩ - 10,0
ANSI 600 (PN 100)• Maximum Operating Pressure, bar - 100,0 (1450 psi)• Pressure of Strength Test, PT, bar - 150,5 (2183 psi)• Working Temperature Range TS, °F - -4° to 212°• Electrical voltage AC 5kV(50Hz) in 1 min. time (in dry condition)• Resistance at voltage DC 1kV (in dry condition) R,MΩ - 10,0
AA in
.9171.0591.3261.6691.9012.3742.9963.500
4.250/4.5005.236
6.259/6.6258.625
10.74812.75114.011
1617.992
2024.01527.992
3235.984
404244
47.99255.984
mm
in
.125
.125
.125
.125
.141
.141
.157
.177
.196
.196
.220
.248
.248
.279
.279
.314
.314
.314
.346
.346
.393
.393
.433
.433
.492
.492
.559
mm
in
1.3261.3261.6692.0072.3742.9964.0004.2505.2366.2597.6259.625
11.75114.00016.00017.51920.00021.45625.78729.84233.85837.39242.12544.29146.25950.19658.267
mm
in
7.8747.8747.8747.8747.8747.8748.6618.6619.4489.8429.842
11.81112.59811.81111.81111.81111.81113.77913.77913.77915.74815.74817.71617.71621.65319.68527.559
8.0708.0708.0708.0708.0708.2678.4648.4649.2519.4489.448
11.81112.59811.81111.81111.81111.81113.77913.77913.77915.74815.74817.71617.71621.65319.68527.559
mm
in
mm
in
1.7711.7711.7711.7711.7712.3624.5274.5274.9216.2996.2997.874
10.23611.81111.81111.81111.81111.81111.81111.81111.81111.81115.74815.74815.74819.68519.685
mm
in
17.71617.71617.71617.71617.71618.50321.65321.65323.62225.59025.59031.49635.43335.43335.43335.43335.43339.37039.37039.37043.30743.30751.18151.18159.05559.05574.803
kglbs
1234
4.56.51013225562
132143243265441463474496670853963
15541609181724253435
5 2
4
• No loss of integrity due to thermal expansion or ground stress as is common with flange isolation gasket kits
• In-factory tested hydrostatically and electrically, to 1 1/2 times their working pressure. Non-destructive testing is also available.
• Maintenance-free, reliable cathodic isolation of equipment in required isolation applications such as compressor stations
The notion that flange isolating gasket kits are more cost efficient than monolithic joints is not well supported when figuring in all the variables.
Materials, labor intensive installation, pre-online inspection and continuous maintenance as well as possible and probable replacement of deteriorated gasket kits all add up, ultimately making the IsoJoInt® a very effective and cost efficient method of cathodic isolation.
BeneFIts & advantages advantage In savIngs
• No labor intensive, complicated installation procedure required as with isolation gasket kits
• No inspection pits, vaults or maintenance needed - weld into place and direct bury - reliable, worry-free cathodic isolation
• Non-conductive epoxy coatings help prevent shorts, both externally and internally
• Isolates stray currents impressed on the pipe from exterior forces such as electrical transmission systems, earth currents and currents flowing from point to point
• Excellent bending and torsional resistance
• Earthquake resistant - Acts as a thrust block or joint
Advance Products and Systems has IsoJoints® ranging in sizes from 1/2” to 150” diameter.
IsoJoInt® MonolIthIc IsolatIon JoInts IsoJoInt® MonolIthIc IsolatIon JoInts
summary
Applications• On existing and new construction• On gas, oil, liquid petrochemical and water lines• Before and from gas distribution stations• On gas or liquid fuel tanks• Under or overground usage
Mechanical Properties• Bodies of monolithic joints are made as rolled and welded construction of steel sheet or forged bodies• All test results are available
Electrical Properties• Highest quality isolating materials• Spark gaps available for extra isolation• No sparking breakdown during 1 minute hydrostatic testing• Isolating resistance above 10MΩ at voltage DC 1kV in dry conditions - standard, higher voltage resistance available• No breakdown during pressured leak testing
Weld end or flanged end typeIsoJoints® are available.
3
4
• No loss of integrity due to thermal expansion or ground stress as is common with flange isolation gasket kits
• In-factory tested hydrostatically and electrically, to 1 1/2 times their working pressure. Non-destructive testing is also available.
• Maintenance-free, reliable cathodic isolation of equipment in required isolation applications such as compressor stations
The notion that flange isolating gasket kits are more cost efficient than monolithic joints is not well supported when figuring in all the variables.
Materials, labor intensive installation, pre-online inspection and continuous maintenance as well as possible and probable replacement of deteriorated gasket kits all add up, ultimately making the IsoJoInt® a very effective and cost efficient method of cathodic isolation.
BeneFIts & advantages advantage In savIngs
• No labor intensive, complicated installation procedure required as with isolation gasket kits
• No inspection pits, vaults or maintenance needed - weld into place and direct bury - reliable, worry-free cathodic isolation
• Non-conductive epoxy coatings help prevent shorts, both externally and internally
• Isolates stray currents impressed on the pipe from exterior forces such as electrical transmission systems, earth currents and currents flowing from point to point
• Excellent bending and torsional resistance
• Earthquake resistant - Acts as a thrust block or joint
Advance Products and Systems has IsoJoints® ranging in sizes from 1/2” to 150” diameter.
IsoJoInt® MonolIthIc IsolatIon JoInts IsoJoInt® MonolIthIc IsolatIon JoInts
summary
Applications• On existing and new construction• On gas, oil, liquid petrochemical and water lines• Before and from gas distribution stations• On gas or liquid fuel tanks• Under or overground usage
Mechanical Properties• Bodies of monolithic joints are made as rolled and welded construction of steel sheet or forged bodies• All test results are available
Electrical Properties• Highest quality isolating materials• Spark gaps available for extra isolation• No sparking breakdown during 1 minute hydrostatic testing• Isolating resistance above 10MΩ at voltage DC 1kV in dry conditions - standard, higher voltage resistance available• No breakdown during pressured leak testing
Weld end or flanged end typeIsoJoints® are available.
3
IsoJoInt® MonolIthIc IsolatIon JoInts
IsoJoInt® provides for current control by separating pipe work into distinct zones and effectively eliminating long-line currents. This assures increased plant and equipment life by reducing or eliminating corrosion damage. Effective control can be attained where a branch is connected to the mainline, where two pipelines of different material connect or where well-coated pipe meets a poorly coated system.
Advance Products and Systems, LLC, is the exclusive provider of the
IsoJoInt® monolithic weld end isolating joints. The IsoJoInt® is manufactured in sizes ranging from 1/2” diameter to 150” diameter with an ANSI rating of 150# to 2500# and up to API 10,000#. All types of carbon and stainless steel are used in their manufacturing.
For truly superior cathodic isolation, Advance Products and Systems offers an IsoJoInt® manufactured according to ASME VIII Division 1 standards and certified by ISO 9001 Quality Assurance making it the supreme monolithic joint on the market today.
G-10 Isolating RingG-10 Isolating Ring
Isolating Filling Material
Zone A
Zone B
Insulating Coating
Isolating Filling Material
This cutaway illustrates the typical isolating properties of IsoJoInt®
Double Seal Gasket System
1520253240506580
100125150200250300350400450500600700800900
10001050110012001400
1/2”3/4”
1”5/4”6/4”
2”2 1/2”
3”4”5”6”8”
10”12’’14”16”18”20”24”28”32”36”40”42”44’’48’’56”
21,326,933,742,448,360,376,188,9
108,0/114,3133,0
159,0/168,3219,1273,0323,9355,9406,4457,0508,0610,0711,0813,0914,0
1016,01067,01118,01219,01422,0
3,23,23,23,23,63,64,04,55,05,05,66,36,37,17,18,08,08,08,88,8
10,010,011,011,012,512,514,2
33,733,742,451,060,376,1
101,6108,0133,0159,0193,7244,5298,5355,6406,4445,0508,0545,0655,0758,0860,0965,0
1070,01125,01175,01275,01480,0
200200200200200200220220240250250300320300300300300350350350400400450450550500700
205205205205205210215215235240240300320300300300300350350350400400450450550500700
454545454560
115115125160160200260300300300300300300300300300400400400500500
450450450450450470550550600650650800900900900900900
1000100010001100110013001300150015001900
0,51,01,31,82,13,04,56,0
10,025,028,060,065,0
110,0120,0200,0210,0215,0225,0304,0387,0437,0705,0730,0824,0
1100,01558,0
in
mmgn min BB A B C L Weight
DN ANSI 150 (PN 25)
mm
AA
BB
gn
B
C
A
L + 5
ANSI 150 (PN 25) ANSI 300 (PN 65) & ANSI 600 (PN 100)
L + 5
B
C
A
BBAA
gn
Basic Parameters of Insulating Joints
ANSI 150 (PN 25)• Maximum Operating Pressure, bar - 25,0 (363 psi)• Pressure of Strength Test, PT, bar - 37,5 (544 psi)• Working Temperature Range TS, °F - -4° to 158°• Electrical voltage AC 5kV(50Hz) in 1 min. time (in dry condition) • Resistance at voltage DC 1kV (in dry condition) R,MΩ - 10,0
ANSI 300 (PN 65)• Maximum Operating Pressure, bar - 63,0 (914 psi)• Pressure of Strength Test, PT, bar - 94,5 (1370 psi)• Working Temperature Range TS, °F - -4° to 212°• Electrical voltage AC 5kV(50Hz) in 1 min. time (in dry condition)• Resistance at voltage DC 1kV (in dry condition) R,MΩ - 10,0
ANSI 600 (PN 100)• Maximum Operating Pressure, bar - 100,0 (1450 psi)• Pressure of Strength Test, PT, bar - 150,5 (2183 psi)• Working Temperature Range TS, °F - -4° to 212°• Electrical voltage AC 5kV(50Hz) in 1 min. time (in dry condition)• Resistance at voltage DC 1kV (in dry condition) R,MΩ - 10,0
AA in
.9171.0591.3261.6691.9012.3742.9963.500
4.250/4.5005.236
6.259/6.6258.625
10.74812.75114.011
1617.992
2024.01527.992
3235.984
404244
47.99255.984
mm
in
.125
.125
.125
.125
.141
.141
.157
.177
.196
.196
.220
.248
.248
.279
.279
.314
.314
.314
.346
.346
.393
.393
.433
.433
.492
.492
.559
mm
in
1.3261.3261.6692.0072.3742.9964.0004.2505.2366.2597.6259.625
11.75114.00016.00017.51920.00021.45625.78729.84233.85837.39242.12544.29146.25950.19658.267
mm
in
7.8747.8747.8747.8747.8747.8748.6618.6619.4489.8429.842
11.81112.59811.81111.81111.81111.81113.77913.77913.77915.74815.74817.71617.71621.65319.68527.559
8.0708.0708.0708.0708.0708.2678.4648.4649.2519.4489.448
11.81112.59811.81111.81111.81111.81113.77913.77913.77915.74815.74817.71617.71621.65319.68527.559
mm
in
mm
in
1.7711.7711.7711.7711.7712.3624.5274.5274.9216.2996.2997.874
10.23611.81111.81111.81111.81111.81111.81111.81111.81111.81115.74815.74815.74819.68519.685
mm
in
17.71617.71617.71617.71617.71618.50321.65321.65323.62225.59025.59031.49635.43335.43335.43335.43335.43339.37039.37039.37043.30743.30751.18151.18159.05559.05574.803
kglbs
1234
4.56.51013225562
132143243265441463474496670853963
15541609181724253435
5 2
IsoJoInt® MonolIthIc IsolatIon JoInts
one piece units, field problems are virtually non-existent and the integrity of the isolation is kept intact.
Furthermore, once installed, IsoJoInt® can be buried and forgotten ending your maintenance worries. In contrast, inspection pits and vaults must be used to monitor below ground isolation gaskets. And constant visual inspections of above ground isolation gaskets are necessary to check for shorts in the gaskets. This requires a continuing maintenance program during the entire life of the pipeline.
90” Diameter IsoJoInt® Monolithic Isolation Joint
IsoJoInt® For superIor CathodIC proteCtIonIsoJoInt® is a true monolithic isolating joint which effectively and efficiently stops short circuits and stray currents from damaging pipelines and equipment. IsoJoInt® employs one or more, preassembled pressure seals and isolating ring. Unlike isolating gasket kits, IsoJoInt® does not depend on an installer fitting gasket, sleeves and washers into a flange on location. Any one of these parts could be damaged causing a complete breakdown of the isolated flange, thus loosing cathodic isolation. Because IsoJoInts® are welded into place as
1520253240506580
100125150200250300350400450500600700800900
10001050110012001400
1/2”3/4”
1”5/4”6/4”
2”2 1/2”
3”4”5”6”8”
10”12”14”16”18”20”24”28”32”36”40”42”44”48”56”
21,326,933,742,448,360,376,188,9
108,0/114,3133,0
159,0/168,3219,1273,0323,9355,9406,4457,0508,0610.0711,0813.0914,0
1016,01067,01118,01219,01422,0
3,23,23,23,63,65,55,05,66,36,37,18,08,88,8
10,011,011,012,012,514,214,216,018,018,020,022,024,0
60,365,076,188,988,9
101,6133,0139,7177,8193,7273,0323,9355,6457,0457,0508,0610,0660,0810,0865,0975,0
1118,01225,01321,01321,01422,01710,0
120120120120120141161161204204237237267244247342342332332300300500500500700
10001000
120120120120120145157157208208237237277254251336336313313300300500500500700
10001000
60606060606482828888
126126156202202222222355355400400400400400400500500
300300300300300350400400500500600600700700700900900
1000100010001000140014001400180025002500
1,41,62,02,73,54,08,0
10,019,035,053,071,093,0
180,0180,0224,0340,0480,0710,0950,0
1250,02270,02240,02428,02680,03800,04500,0
in
DN ANSI 600 (PN 100)
1520253240506580
100125150200250300350400450500600700800900
10001050110012001400
1/2”3/4”
1”5/4”6/4”
2”2 1/2”
3”4”5”6”8”
10”12”14”16”18”20”24”28”32”36”40”42”44”48”56”
21,326,933,742,448,360,376,188,9
108,0/114,3133,0
159,0/168.3219,1273,0323,9355,9406,4457,0508,0610,0711,0813,0914,0
1016,01067,01118,01219,01422,0
3,23,23,23,63,65,55,05,66,36,37,17,17,18,08,08,08,88,8
10,012,514,214,216,016,018,020,020,0
60,365,076,188,988,9
101,6133,0139,7177,8193,7273,0323,9355,6457,0457,0508,0610,0660,0810,0865,0975,0
1118,01225,01321,01321,01422,01710,0
120120120120120141161161204204237237287284284282337387387342342500500500700
10001000
120120120120120145157157208208237237287284284256340390390345345500500500700
10001000
60606060606482828888
126126126132132162223223223313313400400400400500500
300300300300300350400400500500600600700700700700900
1000100010001000140014001400180025002500
1,41,62,02,73,54,08,0
10,019,035,053,083,085,0
120,0140,0165,0300,0350,0600,0750,0910,0937,0
1702,01680,01820,02010,02850,0
ANSI 300 (PN 65)
mm
.125
.125
.125
.141
.141
.216
.196
.220
.248
.248
.279
.314
.346
.346
.393
.433
.433
.472
.492
.559
.559
.629
.708
.708
.787
.866
.944
2.3742.5592.9963.5003.5004.0005.2365.5007.0007.625
10.74812.75014.00017.99217.99220.00024.01525.98431.88934.05538.38544.00048.22852.00052.00055.98467.322
gn min BB A B C L WeightAAmm in kglbs
.9171.0591.3261.6691.9012.3742.9963.500
4.250/4.5005.236
6.259/6.6258.625
10.74812.75114.011
1617.992
2024.01527.992
3235.984
404244
47.99255.984
mm in mm in mm in
4.7244.7244.7244.7244.7245.5516.3386.3388.0318.0319.3309.330
10.5119.6069.724
13.46413.46413.07013.07011.81111.81119.68519.68519.68527.55939.37039.370
4.7244.7244.7244.7244.7245.7006.1816.1818.1888.1889.3309.330
10.90510.0009.881
13.22813.22812.33212.33211.81111.81119.68519.68519.68527.55939.37039.370
2.3622.3622.3622.3622.3622.5193.2283.2283.4643.4644.9604.9606.1417.9527.9528.7408.740
13.97613.97615.74815.74815.74815.74815.74815.74819.68519.685
11.81111.81111.81111.81111.81113.77915.74815.74819.68519.68523.62223.62227.55927.55927.55935.43335.43339.37039.37039.37039.37055.11855.11855.11870.86698.42598.425
33.54.5689
18224277
117156205397397494749
1058156520942756500449385353590883779921
mm inmm inmm in
in
DN
mmgn min BB A B C L WeightAA
mm in kglbsmm in mm in mm inmm inmm inmm in
.9171.0591.3261.6691.9012.3742.9963.500
4.250/4.5005.236
6.259/6.6258.625
10.74812.75114.011
1617.992
2024.01527.992
3235.984
404244
47.99255.984
2.3742.5592.9963.5003.5004.0005.2365.5007.0007.625
10.74812.75014.00017.99217.99220.00024.01525.98431.88934.05538.38544.00048.22852.00052.00055.98467.322
.125
.125
.125
.141
.141
.216
.196
.220
.248
.248
.279
.279
.279
.314
.314
.314
.346
.346
.393
.492
.559
.559
.629
.629
.708
.787
.787
4.7244.7244.7244.7244.7245.5516.3386.3388.0318.0319.3309.330
11.29911.18111.18111.10213.26715.23615.23613.46413.46419.68519.68519.68527.55939.37039.370
4.7244.7244.7244.7244.7245.7006.1816.1818.1888.1889.3309.330
11.29911.18111.18110.07813.38515.35415.35413.58213.58219.68519.68519.68527.55939.37039.370
2.3622.3622.3622.3622.3622.5193.2283.2283.4643.4644.9604.9604.9605.1965.1966.3778.7798.7798.779
12.32212.32215.74815.74815.74815.74819.68519.685
11.81111.81111.81111.81111.81113.77915.74815.74819.68519.68523.62223.62227.55927.55927.55927.55935.43339.37039.37039.37039.37055.11855.11855.11870.86698.42598.425
33.54.5689
18224277
117183187265309364661772
132316532006206637523704401244316283
1 6
Monolithic Isolating Joints
OTHER PRODUCTS AVAILABLE• Kleerband® Flange Protectors• Radolid® Nut Protective Caps• Casing Insulators and End Seals• Innerlynx® - Modular Mechanical Seals• Cathodic Isolating Gaskets• Foreman Night Caps• Safety Spray Shields• U-Bolt Cote® - Coated U-bolts
TO ORDER PLEASE SPECIFY THE FOLLOWING:1. Diameter of pipe 2. ANSI rating3. Grade of pipe material4. Wall thickness5. Product to be transported6. Temperature of transported material (160°F is standard. Higher temperature materials available upon request.)7. Additional X-ray, Non-destructive testing. Electrical and hydrostatic testing is standard. (Please state requirements)
Distributed by:
PO Box 60399 • Lafayette, Louisiana 70596-0399800-315-6009 • 337-233-6116 • FAX 337-232-3860E-Mail: [email protected] • Website: www.apsonline.com
Advance Products & Systems, LLC is not responsible for errors printed in this brochure.
BSI TM
ISO 9001FM 537405
Advance Products & Systems, LLC shall repair or replace (within the limitations of such applicable express written warranty as may be issued by it) any product or portions thereof, which prove to be defective in workmanship or material for a period of 12 months from shipment date. The foregoing in lieu of all warranties, express or implied, and all other obligations or liabilities on the part of APS, on account of the product which it may sell. In no event shall APS be liable for consequential or special damages: nor except as it may otherwise specifically agree in writing, installation, or other work which may be done upon or in connection with the product by APS/ the distribution / dealer or others. THE LIMITED WARRANTIES PROVIDED IN THIS AGREEMENT AND THE OBLIGATIONS AND LIABILITIES OF APS ARE THE ONLY WARRANTIES MADE BY APS AS TO THE PRODUCT. APS MAKES NO EXPRESS OR OTHER IMPLIED WARRANTIES, BY COURSE OF DEALING, USAGE OF TRADE, MERCHANTABILITY, FITNESS FOR A PARTICULAR USE (WHETHER GENERAL OR SPECIFIC), OR OTHERWISE.
I S O - 9 0 0 1 C e r t i f i e d C o m p a n y - F M 5 3 7 4 0 5
072516
Isojoint® Benefits & Advantages -see pages 4-5
Isojoint® Design -see page 3