mount bulletin vertical antenna mount for 2 4 m 8 ft and 3 m 10 ft parabolic antennas
TRANSCRIPT
8/4/2019 Mount Bulletin Vertical Antenna Mount for 2 4 m 8 Ft and 3 m 10 Ft Parabolic Antennas
http://slidepdf.com/reader/full/mount-bulletin-vertical-antenna-mount-for-2-4-m-8-ft-and-3-m-10-ft-parabolic 1/4
Bulletin 237391
Revision 'D'
Vertical Antenna Mountfor 2.4m (8ft) and 3m (10ft) Parabolic Antennas
Installation Instructions
DescriptionInstructions given in this bulletin apply to the mount assemblyfor shielded and unshielded antennas with diameters of 2.4 m(8ft) and 3 m (10ft). The mount attaches to the reflector at 3 pointsand is offset from the center of the reflector to accomodate thefeed. The mount may be offset from either side of the feed centerby 200mm (8”) and attaches to the antenna mounting pipe of thetower with 4 U-bolts. Inverting the mount position on the reflectorprovides the alternate offset from the feed center.
The U-bolts can be loosened for coarse azimuth adjustment. Afine azimuth strut assembly is included for adjustment of azi-muth from -5° to +5°. The mount also includes an elevationassembly for adjustment of elevation from -5° to +5°.
Shielded antennas require a fixed strut and strut bracket at therim of the reflector for greater stability. This strut is located on theopposite side of antenna center from the azimuth adjustmentstrut.
Notice
The installation, maintenance, or removal of antenna systemsrequires qualified, experienced personnel. Andrew installationinstructions have been written for such personnel. Antennasystems should be inspected once a year by qualified person-nel to verify proper installation, maintenance, and condition ofequipment.Andrew disclaims any liability or responsibility for the results ofimproper or unsafe installation practices
ECO 5093889 INDEX
ToolsStandard hand tools can be used for this installation. A ratchetand deep well wrench sockets are recommended. However,combination wrenches, box or open-end type, may be used.Wrench sizes for the furnished bolt hardware are as follows:
Wrench size Bolt size
10 mm M6
16-17 mm M10
18-19 mm M1224 mm M16
30 mm M20
Antennamounting
ring Reflector
Elevationadjustmentassembly
Mountassembly
Antennamountingpipe ontower
Fixed strut
Azimuthstrut
Supportcollar
Reflector Mount Feed
Shield Radome
Radome
Sequence of Antenna Assembly
8/4/2019 Mount Bulletin Vertical Antenna Mount for 2 4 m 8 Ft and 3 m 10 Ft Parabolic Antennas
http://slidepdf.com/reader/full/mount-bulletin-vertical-antenna-mount-for-2-4-m-8-ft-and-3-m-10-ft-parabolic 2/4
21
M20X45galvanised
AzimuthU-bracket
Lockwasher
Nut
3
4
5
M20X45galvanised
Lockwasher
Nut
Hinge
Jam nut,stainless steel
Concave nut,brass
Convex washerstainless steel
M20 elevationeyebolt
Offset left -standard
M12X45galvanised
Lock
washer
Nut
Feed location
Offset right -inverted
Red stripehere marks
top of reflector
Reflector Top
8/4/2019 Mount Bulletin Vertical Antenna Mount for 2 4 m 8 Ft and 3 m 10 Ft Parabolic Antennas
http://slidepdf.com/reader/full/mount-bulletin-vertical-antenna-mount-for-2-4-m-8-ft-and-3-m-10-ft-parabolic 3/4
M12 U-bolts
Nut
Lockwasher
M12-38N-m(28-Ib-ft)
U-bolts (2)
U-bolts (2)
Support collar
6 7Hinge
Antennamounting ring
Lockwasher
Nut
M20X45galvanised
8
9
2
2
2
M12 - 38 N-m(136 Ib ft)
M20 - 95 N-m(70 Ib ft)
3
4
U-bracket
M20x90,galvanised
Azimuthstrut
Lockwasher
Nut
Mount
M12 - 38Nm (28 Ib-ft)M16 - 95Nm (70 Ib-ft)M20 - 185Nm (136 Ib-ft)
M20 - 185 n-M(136 Ib ft) 1
1
M12x45 carriagebolt, galvanised
Flat washer
SupportC o l l a r
M10 U-Bolt
Azimuthadjustment
rod
Nut, M16, Brass
Flat washer,stainless steel
LockWasher,SS
Nut, BrassMax Torque
11.5Nm (8.5lb-ft)
M16x45 setscrew,40N-m, and lock
nut, SSlock
washerNut M16x55bolt,
galvanized
Antenna mounting pipeon tower
Nut
Plainwasher
8/4/2019 Mount Bulletin Vertical Antenna Mount for 2 4 m 8 Ft and 3 m 10 Ft Parabolic Antennas
http://slidepdf.com/reader/full/mount-bulletin-vertical-antenna-mount-for-2-4-m-8-ft-and-3-m-10-ft-parabolic 4/4
5
Azimuth
strut
Fixed
strut
25º
25º
25º
Telephone: 708/349-3300
FAX (U.S.A.): 1-800/349-5444 TELEX: 25-3897
Customer Service, 24 hours: U.S.A. • Canada • Mexico: 1-800/255-1479
U.K.: 0800 250055 • Republic of Ireland: 1 800 535358 Other Europe: +44 592 782 612 Printed in E.C. Apr'06
Copyright © 1994 by Andrew Corporation
Andrew Corporation
10500 West 153rd Street Orland Park, IL U.S. A. 60462
10
11
12Limits of strut
position forattachment to
tower member
Lockwasher
M6 x 30
Flatwasher
Nut
M6 - 8Nm (6 Ib-ft)
Fixed strut
M20x45galvanised
Lockwasher
Nut
M16 - 95Nm (70 Ib-ft)M20 - 185Nm (136 Ib-ft)
Hereby ANDREW, a Commscope Company, declares that this antenna is in compliance with the essentialrequirements of EU Directive 1999/5/EC. A copy of the declaration is available at www.ANDREW.com
Ø22.5(7/8") Mounting hole.NOTE: HOLES SHOULD NOT BE DRILLED
WITHOUT PRIOR APPROVAL OF THE TOWERMANUFACTURER