GLUETEC Industrieklebstoffe GmbH & CO.KG · Am Biotop 8a · D-97259 Greußenheim

Tel.: +49 (0) 93 69 / 98 36 0 · Fax: +49 (0) 93 69 / 98 36 10 · www.gluetec.de · info@gluetec.de

HIGH TACK

MS Polymer Adhesives & Sealants

MS Polymer - High Tack white, black

WIKO MS Polymer - High Tack is a high-quality, one-component, elastic adhesive based on MS polymer. A special feature of the product is its extremely high initial adhesive strength.

Trading units Item no. : 290ml cartridge MSPHTW.K290 600ml bag MSPHTW.B600

290ml cartridge MSPHTS.K290 600ml bag MSPHTS.B600

TDB revised on 10/04/2016 V04_0416

Advantages

•  Quick full curing •  Universally applicable •  Resistant to salt water, fresh water and moisture •  Wide adhesion spectrum on many surfaces without primer •  Permanently elastic •  High mechanical resistance •  Almost odourless •  Recoatability wet in wet (due to the high number of systems on the market, pre-testing necessary) •  Free of isocyanate and silicone •  High initial adhesion •  Resistant to water •  Well suited for the absorption of acoustic noise and vibration

Page 1 / 2

TECHNICAL DATA SHEET

Technical Data (25°C, 50% humidity)

Basis: MS polymer (moisture-curing) Density: Approx. 1,57 g/ml Skin formation time: Approx. 10 – 15 minutes Curing: Approx. 3 mm/24 hours Shore hardness A: Approx. 55 (DIN 53505) Elastic modulus 100%: 1,4 N/mm2 (DIN 53504) Tensile strength: 2,2 N/mm2 (DIN 53504) Elongation at break: Approx. 335% (DIN 53504) Processing temperature: minimum + 5 °C to a maximum + 35 °C Temperature resistance: minimum - 40 °C to a maximum + 90 °C

GLUETEC Industrieklebstoffe GmbH & CO.KG · Am Biotop 8a · D-97259 Greußenheim

Tel.: +49 (0) 93 69 / 98 36 0 · Fax: +49 (0) 93 69 / 98 36 10 · www.gluetec.de · info@gluetec.de

HIGH TACK

MS Polymer Adhesives & Sealants

MS Polymer - High Tack white, black

Shelf Life

Shelf life cartridge: 12 months (in unopened original packaging) Shelf life bag: 12 months (in unopened original packaging)

Storage temperature: minimum + 5°C to a maximum of + 25°C Resistance to frost during transportation: - 15°C

Application Areas

Installation and construction adhesive to bond mirrors, natural stones, plaster, PSPU, PVC, diverse plastics, enamel copper, lead, zinc, aluminium, stainless steel, HPL panels, cement "bre panels, colour codes, wood, glass ,etc.

Sealant for bodywork (vehicles) and metal joints (air ducts). Metal adhesive (able to resist vibrations).

Application conditions

The product can be applied with good adhesion on a high number of materials, paint or vanishing systems, metals, glass, mirrors, ceramics and diverse plastics, without priming. The surface needs to be clean and free of grease and dust (use WIKO plastic cleaner respectively WIKO metal cleaner). Please consider our list of pre-treatment possibilities listed in the WIKO – catalogue for potential pre-treatment possibilities. Due to the high number of different surfaces, the adhesion quality should be determined by a performance test.

Apply the material with a suited dispensing system and process the MS Polymer with the counterpart material within the skin formation time. The layer of the material should be adapted to the maximal expected strength and joint movement. A "xing of the bond is recommended until the material is fully cured. The curing depends on the thickness of the layer, the temperature and the humidity.

Clean unmeant impurities of the working equipment immediately after usage with WIKO plastic cleaner (Item no.: AKSR.D500 or WIKO metal cleaner (Item no.: AMTR.D500).

The information contained in this data sheet, especially the suggestions for processing and application of products, is based on our experience and newest expertise. Due to the facts that materials can be very diverse and that we have no in#uence on the working conditions, we recommend to perform sufficient tests to validate the compatibility of the products. Our company shall neither be held liable for this information nor for a verbal or written consultation. Additionally, please consider the information of our safety data sheets.

Restrictions

Not suited for PE, PC, PP, PMMA, PTFE, neoprene, bituminous surfaces and bonding under water.

TDB revised on 10/04/2016 V04_0416

TECHNICAL DATA SHEET

Page 2 / 2