E-14510-7701-01C6856651INSTALLATION MANUALfor Product Code 4040/4041/4042MT-501 Mailbin KitApplied Machine:/ /I. Outline of Installation Procedures for bizhub 200/bizhub 250/bizhub 350 SystemWhen installing the machine and associated options as a system, follow the order shown on the upper.Note: For the detailed installation procedures for each option, follow the instructions given in the correspondingInstallation Manual and perform the procedures correctly.DK-501 PC-102 PC-402 PC-202Dehumidifier Heater 1CDF-605JS-502 FS-508SD-502OT-601MachinePU-501HD-504EM-303/EM-304/EM-305FK-503 SU-501 MT-501ML-502EK-502OC-5024510U027AAE-2II. Accessory parts III. Installation Procedures1. Turn off the machine and unplug the power cordfrom the power outlet.2. RemovetheMailbinKitandotheraccessoriesfromthepackagingboxandpeeloffpiecesofprotective tape.3. Remove the Finisher Exit Tray (two screws).4. RemovetherightandleftExitTrayMountingHolders (one screw each).No. Name Figure Qty1. Mailbin Unit12. Exit Tray43. MountingBracket (Right)14. MountingBracket (Left)15. Misfeed Clearing Lever16. Screw A27. Screw B68. Label19. Installation Manual1 setAfterunpacking,besuretogetridofthepackaging materials and keep them out ofthe reach of children.Putting your head in the wrapper involvesdanger of suffocation.4510U001AA4510U002AA4510IXC012DA4510IXC013DA4510U002AA4510U006AA4510U006AA4980IXC019DA4510U009AC4510U030AA4510IXC010DA4510IXC001DAE-35. Removetherightandleftcovers(twoscrewseach).6. Using nippers, cut out the knockouts.7. Place the Mounting Brackets (Right and Left).Note:Makesurethattheflatsurfacesofthebracketsface inward.8. Using six screw Bs furnished with the Mailbin Kit,securetheMountingBracketsinpositionfollow-ingtheordershownintheillustration(threescrews each).9. Reinstalltherightandleftcovers,whichhavebeen removed in step 5 (two screws each).10.ReinstalltheleftExitTrayMountingHolderthathas been removed in step 4 (one screw).Note:Installtheholderatalevelonesteplowerthanthat, from which it has been removed.4510IXC002DA4510U013AA4510IXC008DA4510U015AA3123124510IXC003DA4510IXC004DAE-411.Usingnippers,cutoutthecrosshatchedportionoftherightExitTrayMountingHolderthathasbeen removed in step 4.12.Reinstall the right Exit Tray Mounting Holder (onescrew).Note:Installtheholderatalevelonesteplowerthanthat, from which it has been removed.13.ReinstalltheFinisherExitTraythathasbeenremoved in step 3 (two screws).14.Loosen the screw shown in the illustration, moveit in the direction of the arrow, and tighten it again.Note:This step should be done securely.If not, any trouble may happen.Do not move the screw by using the Adjust Plate.Be sure to move the screw itself.15.Mount the Mailbin Unit on the Finisher.16.Push the Mailbin Unit in the direction of the arrowso that it locks in position.17.UsingtwoscrewAsfurnishedwiththeMailbinKit, secure the Mailbin Unit.4510U028AA4510IXC005DA4510IXC011DA4510IXC009DAAdjust Plate4510U021AAAlignmentMarkingUsedWhenPlacingthe Mailbin Unit4510U022AAE-518.Remove the connector cover of the Finisher (onescrew).19.Using nippers, cut out the knockout.20.Remove one screw for the ground wire and thensecuretwogroundwirestogetherusingonescrew.21.Connect the connector.22.Fit the snap band.23.Reinstalltheconnectorcoverthathasbeenremoved in step 18 (one screw).24.Install four Exit Trays.25.Open the Misfeed Clearing Cover and install theMisfeed Clearing Lever.26.Affix the Label onto the Finisher.4510IXC006DA4510IXC007DASnap Band4510U025AA4510U026AA4510U029AB